Sharp PN-525U User Manual

PN-525U
LCD MONITOR
MONITEUR LCD
ENGLISH FRANÇAIS
OPERATION MANUAL
MODE D’EMPLOI
ENGLISH ...... E1
FRANÇAIS .... F1
PN-525U
LCD MONITOR
ENGLISH
IMPORTANT: To aid reporting in case of loss or theft, please record the product’s model and serial numbers in the space provided. The numbers are located in the rear of the product.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING:
CAUTION: TO REDUCE THE RISK OF ELECTRIC
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
U.S.A. ONLY
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CAUTION:
The AC outlet shall be installed near the equipment and shall be easily accessible.
1
E
IMPORTANT INFORMATION (Continued)
WARNING:
U.S.A. ONLY
CAUTION:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Use the supplied power cord as it is.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. U.S.A. ONLY
This product utilizes fluorescent tubes containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eia.org
E
2
DEAR SHARP CUSTOMER
Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.
SAFETY PRECAUTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.
1. Read instructions — All operating instructions must be read and understood before the product is operated.
2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future reference.
3. Observe warnings — All warnings on the product and in the instructions must be observed closely.
4. Follow instructions — All operating instructions must be followed.
5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.
6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.
7. Water and moisture — Do not use the product near water.
8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.
Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life
of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings. Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.
9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from resting on them.
10. The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts.
For the same reason, do not spill water or liquid on the product.
13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.
14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs. a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions. Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls
not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified
technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product
needs servicing.
3
E
SAFETY PRECAUTIONS (Continued)
15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement
parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.
16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.
17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method
recommended by the manufacturer.
18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).
19. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate counter measures.
E
4
TIPS AND SAFETY INSTRUCTIONS
- The TFT color LCD panel used in this monitor is made with
the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.
- Do not display a still picture for a long period, as this could
cause a residual image.
- Never rub or tap the monitor with hard objects.
- Please understand that Sharp Corporation bears no
responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.
- This monitor and its accessories may be upgraded without
advance notice.
- Do not use the monitor where there is a lot of dust, where
humidity is high, or where the monitor may come into contact with oil or steam, as this could lead to fire.
- Ensure that the monitor does not come into contact with
water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock.
- Do not place the monitor on top of unstable objects or in
unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.
- Do not use the monitor near heating equipment or in places
where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.
The Power Cord
- Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords. Damage to the cord may result in fire or electric shock.
- Use only the power cord supplied with the monitor.
- Insert the power plug directly into the AC outlet. Adding an extension cord may lead to fire as a result of overheating.
- Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.
Manual Scope
- Microsoft and Windows are registered trademarks of Microsoft Corporation.
- This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.
- All other brand and product names are trademarks or registered trademarks of their respective holders.
- Language of OSD menu used in this manual is English by way of example.
- Illustrations in this manual may not exactly represent the actual product or display.
- This manual assumes use in horizontal orientation, except where specifically noted.
Fluorescent Tubes
● The fluorescent tubes in this product have a limited lifetime. * If the screen gets dark, flashes, or does not turn on,
change the fluorescent tubes with new exclusive ones.
* For more information, please contact your product
dealer.
● Because of the property of fluorescent tubes, the screen may flash during the initial period of use. If this happens, please turn off the main power switch of the monitor and turn on again to confirm operation.
5
E
Contents
Introduction
IMPORTANT INFORMATION ............................................1
DEAR SHARP CUSTOMER ..............................................
SAFETY PRECAUTIONS ..................................................
TIPS AND SAFETY INSTRUCTIONS ...............................
Supplied Accessories ......................................................
Part Names .......................................................................7
Front view .....................................................................7
Rear view .....................................................................8
Remote control unit ......................................................8
Connection and Installation
How to Install the Monitor ...............................................9
Mounting precautions ...................................................9
Connecting Peripheral Equipment ...............................10
Connection with a PC .................................................10
Connection with AV equipment ..................................
Other terminals ...........................................................11
Connecting external speakers ....................................11
Connecting multiple monitors ..................................... 11
Connecting the Power Cord .........................................12
Mounting the Temporary Stands ..................................
Binding Cables ...............................................................13
Preparing the Remote Control Unit ..............................13
Installing the batteries ................................................13
Remote control operation range .................................13
Basic Operation
Turning Power On/Off ....................................................14
3 3 5 7
Turning on the main power ........................................
Turning power on/off ..................................................
Disabling power on/off operations ..............................14
Basic Operation .............................................................15
Menu Items .....................................................................17
Displaying the menu screen .......................................17
Menu item details .......................................................18
Adjustments for PC screen display ............................22
Initialization (Reset)/
Functional Restriction Setting ..................................23
PC Operation
Controlling the Monitor with a PC ................................24
PC connection ............................................................24
10
Communication conditions .........................................24
Communication procedure .........................................24
RS-232C command table ...........................................28
Troubleshooting and Specifications
12
Troubleshooting .............................................................32
Specifications ................................................................
14 14
33
E
6
Supplied Accessories
INPUT
Liquid Crystal Display: 1
Remote control
unit: 1
Cable clamp: 2� Temporary stand: 2 � Power cord
clamp:
1
Power cord (Approx. 13.1 feet [4 m]): 1“AA” size battery: 2CD-ROM (Utility Disk for Windows): 1Operation manual: 1Blank sticker: 1
Place a blank sticker onto the SHARP logo to cover the logo
.
Vertical logo
sticker: 2
IN
P
U
T
1
2 3
4
5
If any component should be missing, please contact your dealer.
* Sharp Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission. * For environmental protection! Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
Front view
Part Names
1. LCD panel
2. Remote control sensor (See page 13.)
3. Input switch (See page 15.)
4. Power switch (See page 14.)
5. Power LED (See page 14.)
TIPS
• Use a pointed object such as a pen tip to press the switches at the front of the monitor.
7
E
Part Names
1 6 8 9 11 14
2 3 4 5 7 10 12 1
3
15
16
1
2
3
4
5
6
9
8
7
Rear view
1. Main power switch (See page 14.)
2. AC input terminal (See page 12.)
3. PC/AV output terminal (DVI-D) (See page 11.)
4. PC1 input terminal (DVI-D) (See page 10.) AV1 input terminal
5. PC2 input terminal (Mini D-sub 15 pin) (See page 10.)
6. PC3 input terminals (BNC) (See page 10.)
7. AV2 input terminals (BNC) (See page 10.)
8. AV3 input terminal (BNC) (See page 10.)
9. RS-232C output terminal (D-sub 9 pin) (See page 24.)
10. RS-232C input terminal (D-sub 9 pin) (See page 24.)
11. External speaker terminals (See page 11.)
12. PC/AV audio output terminals (See page 11.)
13. AV audio input terminals (See page 10.)
14. PC audio input terminal (See page 10.)
15. Handles
16. Vents
(DVI-D) (See page 10.)
Remote control unit
1. Signal transmitter
2. POWER button (See page 14.)
3. MUTE button (See page 15.)
4. VOL +/- buttons (See page 15.)
BRIGHT +/- buttons (See page 15.) Cursor control ( / / / ) buttons
5. DISPLAY button (See page 15.)
6. MODE button (See page 15.)
7. INPUT button (See page 15.)
8. MENU button (See page 17.)
9. SIZE button (See page 15.)
E
8E8
How to Install the Monitor
For the monitor in horizontal orientation
7-7/8 [20]
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
For the monitor in vertical orientation
Unit: inch [cm]
2 [5]
2
[5]
2
[5]
7-7/8 [20]
*
*
*
INPUT
Mounting precautions
• Since the monitor is heavy, consult your dealer before installation.
• When installing or moving the monitor, ensure that this is carried out by at least 2 people.
• A stand and mounting bracket compliant with VESA specifications is required. Do not use any screw holes other than VESA holes for installation.
• When moving the monitor, be sure to hold it with the handles both on the rear and the unit bottom. Do not hold the LCD panel. This may cause product damage, failure, or injury.
• Install the monitor with the surface perpendicular to a level surface. If necessary, limit the tilt between 0 and 20 degrees downward.
• Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling.
• This monitor should be used at an ambient temperature between 32°F (0°C) and 104°F (40°C). Provide enough space around the monitor to prevent heat from accumulating inside.
If it is difficult to provide such space because the monitor is
installed inside a housing or for other reasons, take other measures to keep the ambient temperature between 32°F (0°C) and 104°F (40°C) such as installing a fan in the housing.
• Adhere to the following when installing the monitor in the vertical orientation. Failing to adhere to the following may cause malfunctions.
- Install the monitor such that the power LED is located on
the downside.
- Set the MONITOR on the SETUP menu to PORTRAIT.
(See page 19.)
• Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction.
• After mounting, it is recommended to take some measures to prevent the monitor from falling down.
• Do not place the monitor on a device which generates heat.
• Be sure to use a stand or a wall-mount/ceiling-mount bracket designed or designated for mounting the monitor.
• This monitor is designed to be installed on a concrete wall/ ceiling or pillar. Reinforced work might be necessary for some materials such as plaster / thin plastic board / wood before starting installation. This monitor and bracket must be installed on a wall which can endure at least 3 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.
• Use the supplied vertical logo sticker when you install the monitor in vertical orientation.
* The monitor can be installed close to a wall, etc.
However, the monitor emits heat during operation. Be aware that heat emitted from the monitor may discolour or alter the wall.
* Do not remove the factory-affixed sticker but affix the logo
sticker over it. Be careful not to cover the remote control sensor or buttons.
9
E
Connecting Peripheral Equipment
PC1 input terminal
PC audio input terminal
PC2 input terminal
PC3 input terminals
HV
R G
B
AV1 input terminal
AV audio input terminals
AV2 input terminals
AV3 input terminal
Cr/Pr Y Cb/Pb
Caution
• Be sure to turn off the main power switch and disconnect the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected.
• Be careful not to mix up the input terminal with the output terminal when connecting cables. Mixing up the input and output terminals may cause malfunctions and the other problems.
Connection with a PC
• Use a commercially available signal cable (DVI-D 24 pin) for the PC1 input terminal. Set DVI SELECT on the OPTION menu to PC (DIGITAL) when using the PC1 input terminal. (See page 19.)
• Use a commercially available signal cable (Mini D-sub 15 pin) for the PC2 input terminal.
• Use a commercially available signal cable (BNC) for the PC3 input terminals. Set BNC SELECT on the OPTION menu to PC (ANALOG) when using the PC3 input terminals. (See page 19.)
• Use a commercially available audio cable (mini stereo jack) for the PC audio input terminal. Use an audio cable without resistance.
TIPS
• Images may not be displayed properly depending on the computer (graphics board) to be connected.
• A screen with 1920 x 1080 resolution may not be displayed correctly on PC3 (BNC). In this case, check the settings of your computer (graphics board) to verify that input signals conform to specifications of this monitor (Hsync: 66.3 kHz, Vsync: 60 Hz, and Dot frequency: 148.5 MHz). (See page
34.)
• If there is a check box to disable EDID in display control panel, check it when using PC3 (BNC).
• Use the automatic screen adjustment when a PC screen is displayed for the first time using PC2 or PC3, or when the setting of the PC is changed. (See page 22.)
• The screen is adjusted automatically when SELF ADJUST in the OPTION menu is set to “ON”. (See page 19.)
Connection with AV equipment
• Use a commercially available signal cable (DVI-D 24 pin) for the AV1 input terminal. Set DVI SELECT on the OPTION menu to AV (DIGITAL) when using the AV1 input terminal. (See page 19.)
• Use a commercially available component cable (BNC) for the AV2 input terminals. Set BNC SELECT on the OPTION menu to AV (COMPONENT) when using the AV2 input terminals. (See page 19.)
• Use a commercially available video cable (BNC) for the AV3 input terminal.
• Use a commercially available audio cable (RCA) for the AV audio input terminals.
• The AV1 input terminal is compatible with the video signals below:
1920 x 1080 p @ 50/59.94/60 Hz 1920 x 1080 i @ 50/59.94/60 Hz 1280 x 720 p @ 50/59.94/60 Hz 720 x 576 p @ 50 Hz 720 x 480 p @ 59.94/60 Hz 640 x 480 p @ 59.94/60 Hz
• The AV2 input terminals are compatible with the video signals below:
1080i(1125i)/50,1080i(1125i)/60,720p(750p)/50, 720p(750p)/60,576p(625p),576i(625i),480p(525p), 480i(525i)
E
10
Connecting Peripheral Equipment
(1) (2)
shows the signal flow
PC/AV output terminal
PC1/AV1 input terminals
Digital signal (DVI) cables (commercially available)
To PC digital RGB output terminal
First monitor Second monitor
Other terminals
PC/AV audio output terminals
• Audio from the equipment connected to the AV audio input terminals or PC audio input terminal is output. Connect to the audio input terminals of the connected equipment using a commercially available audio cable (RCA).
• The audio output varies depending on the input mode selection. (See page 15.)
• The volume level can be adjusted using the volume adjustment. (See page 15.)
• Selecting FIXED of “AUDIO OUTPUT” from the OPTION menu fixes the volume of sound output from the audio output terminals. (See page 19.)
• Audio signals output from the PC/AV audio output terminals cannot be adjusted using the AUDIO menu.
PC/AV output terminals
Video signals from PC1 and AV1 can be output to HDCP-compatible external device. Use this terminal when you connect multiple monitors in a daisy chain via DVI cable (commercially available). (See the description on the right.) Images cannot be output to device that is not HDCP-compatible.
RS-232C input/output terminals
You can control the monitor from a PC by connecting a commercially available RS-232 straight cable between this terminal and the PC. (See page 24.)
Connecting multiple monitors
You can connect multiple monitors (up to 5 monitors) in a daisy chain by using the PC1/AV1 input terminals and PC/AV output terminals of this monitor.
Connection example
Connecting external speakers
Be sure to use external speakers with an impedance of 6 Ω and a rated input of at least 7 W.
1. While pushing the tab, insert the tip of the cable.
2. Release the tab.
TIPS
• Be sure to connect the + and - terminals and the left and right speakers properly.
• Avoid short circuiting the + and - terminals.
TIPS
• The length of the signal cables or surrounding environment may affect the image quality.
• The screen may not display properly when using terminals other than PC1/AV1 for the input mode. In this case, turn off the power to all the monitors connected in a daisy chain and then turn the power on again.
11
E
Connecting the Power Cord
Be sure to use a power outlet of AC 120 V (60 Hz).
Using power supply other than the one specified may cause fire.
Power cord (Supplied)
Power outlet
AC input terminal
3
2
1
Main power switch
Temporary stand
Screws
Caution
• Do not use a power cord other than the one supplied with the monitor.
Mounting the Temporary Stands
Caution
• The monitor is heavy. Make sure to handle the monitor with at least 2 people.
• Please note that the temporary stands are for temporary use only until the monitor is properly mounted.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
Remove the screws from the monitor and mount the temporary stand using the screws.
The temporary stand can be mounted at a position shown in the illustration.
Caution
• After detaching the temporary stand, be sure to re-mount the removed screws on the monitor.
E
12
10°
16.4 feet (5 m)
16.4 feet (5 m)
16.4 feet (5 m)
Remote control sensor
10°
Binding Cables
1 2 3
Hole for the power
cord clamp Fastened part
Band Power cord
clamp
Cable clamp
Insert the cable clamp into a hole. (any hole available)
Cable clamp attachment
Cable clamp positions
Attaching the cable clamp
The cables connected to the terminals on the back of the monitor can be neatly bundled using the supplied cable clamps as shown in the illustration.
Caution
• Verify the position for attaching a cable clamp in advance. A cable clamp cannot be removed once it is attached.
Fastening the power cord
The power cord can be fastened using the supplied power cord clamp. This will prevent the power cord from being disconnected accidentally.
1. Attach the supplied power cord clamp to the power cord, making sure the power cord clamp is circular hole­sidedown.
2. Insert the tip of the band into the hole for the power cord clamp.
3. While holding the tail of the band, slide the fastened part toward the AC input terminal.
Preparing the Remote Control Unit
Installing the batteries
1. Press the cover gently and slide it in the direction of the arrow.
2. See the instructions in the compartment and put in the supplied batteries (2 “AA” size batteries) with their plus (+) and minus (-) sides oriented correctly.
3. Close the cover.
TIPS
• The supplied batteries (2 “AA” size batteries) may become exhausted faster depending on the storage condition. It is recommended that you replace them with new batteries (commercially available) earlier than specified.
• If you will not use the remote control for a long time, remove the batteries.
• Use manganese or alkaline batteries only.
Remote control operation range
The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10° from the center to the top/bottom/right/left of the remote control sensor.
TIPS
• Do not expose the remote control unit to shock by dropping or stepping on it. This could lead to a malfunction.
• Do not expose the remote control unit to liquids, and do not place it in an area with high humidity.
• The remote control unit may not work properly if the remote control sensor is under direct sunlight or strong lighting.
• Objects between the remote control unit and the remote control sensor may prevent proper operation.
• Replace the batteries when they run low as this may shorten the remote control’s operation range.
• If a fluorescent light is illuminated near the remote control unit, it may interfere with proper operation.
• Do not use it with the remote control of other equipment such as air conditioner, stereo components, etc.
13
E
Turning Power On/Off
Main power switch
INPUT
Power LED
DATE/TIME SETTING
SET
CANCEL
07
/ /
OK
[MENU]
20
01/01/00 00
:
: :
MENU
Caution
• Turn on the monitor first before turning on the PC or playback device.
Turning on the main power
When the main power switch is off, the monitor cannot be turned on using the POWER button on the remote control unit.
Turning power on/off
TIPS
• If the monitor is in the input signal standby mode and you press the POWER button on the remote control unit, the monitor enters standby mode.
• You can turn on/off the monitor by pressing the power switch of the monitor.
• Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.
Date/time setting
• If the time has yet to be set when the monitor is first turned on, the date/time setting screen appears. Set the date and time.
Press the POWER button to turn the power ON/OFF.
Status of a power LED Status of the monitor
Green lighting Power “On” Orange lighting Power “Off” (Standby mode)
Green flashing
Caution
• When switching the main power switch or the POWER button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction.
Input signal standby mode (input using a PC)
1. Press , , or to select the date and time, and press or to change the numerical values.
2. Select SET and then press
.
• Be sure to set the date and time.
• The date/time setting screen will close automatically if no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the OPTION menu when the date/time setting screen disappears.
TIPS
• Set the date in “Year/Month/Day” order.
• Set the time on a 24-hour basis.
• The clock stops after the power-off status continues for approximately 1 week.* The date/time setting screen appears at power-on. Be sure to set the date and time. (* This is a guide. The power-off status that stops the clock
depends on the status of the monitor.)
Disabling power on/off operations
Power on/power off operations can be disabled in order to protect the monitor from an accidental power off. Set the ADJUSTMENT LOCK in FUNCTION menu to “2”. (See page
23.)
E
14
Basic Operation
1
2
3
4
5
6
7
8
V O L U M E 15
B R I G H T 15
INPUT MODE
SIZE
COLOR MOD
E
BRIGHT
VOLUM
E
ID No.
MODE
L
S/N
PC2 ANALOG
WIDE
ST
D
15
15
0
PN-525
U
:
:
:
:
:
:
:
:
1 0 2 4 x7 6 8
INFORMATION XXXX/XX/XX XXX XX:XX:X
X
V: 60 Hz H: 48.4 kH
z
1. INPUT (Input mode selection)
The menu is displayed. Press or to select the input mode, and press to enter.
* You can select the input terminal by pressing the input
switch of the monitor.
Input mode Video Audio
PC1 DIGITAL PC2 ANALOG PC3 ANALOG AV1 DIGITAL AV2 COMPONENT AV3 VIDEO AV3 input terminal
*1
*2
*1
PC1 input terminal PC2 input terminal PC3 input terminals AV1 input terminal
*2
AV2 input terminals
PC audio input terminal
AV audio input terminals
5. BRIGHT +/- (Backlight adjustment)
Pressing or displays the BRIGHT menu when the menu screen is not displayed.
Press or to adjust the brightness.
* If you do not press any buttons for about 4 seconds, the
BRIGHT menu automatically disappears.
6. SIZE (Screen size selection)
The menu is displayed. Press or to select the screen size. (See page 16.)
7. DISPLAY
Displays monitor information. The display disappears when this button is pressed again or disappears automatically after approximately 15 seconds.
8. MODE (Color mode selection)
Each time you press this button, the color mode changes in the following order:
STD (Standard) → VIVID → sRGB → STD...
*1 Select the terminal for DVI SELECT. (See page 19.) *2 Select the terminal for BNC SELECT. (See page 19.)
TIPS
With the AUTO INPUT CHANGE function set upon shipping from the factory, the input mode automatically switches over to an input to which a video signal is input. (See page 19.)
2. MUTE
Turns off the volume temporarily. Press the MUTE button again to turn the sound back to the previous level.
3. MENU
Displays and turns off the menu screen (see page 17).
4. VOL +/- (Volume adjustment)
Pressing or displays the VOLUME menu when the menu screen is not displayed.
Press or to adjust the volume of the sound.
* If you do not press any buttons for about 4 seconds, the
VOLUME menu automatically disappears.
• sRGB applies to PC input only.
sRGB is international standard of color representation
specified by IEC (International Electrotechnical Commission). Color conversion is made in taking account of liquid crytal’s characteristics and represents color tone close to its original image.
E
15
Basic Operation
Switching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDE PC input Displays image so it fills the entire screen.
AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen.
ZOOM 1 PC input An image with a 4:3 aspect ratio is enlarged to fill the entire screen
without changing the aspect ratio. The edges of the image may be
AV input
ZOOM 2 PC input Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMAL PC input Displays image so it fills the screen without changing the aspect
cut off.
ratio of the input signals.
AV input
DotbyDot PC input Displays the dots of the signals input from the connected PC as the
AV input
*: With a monitor with a screen resolution of 1600 x 1200, selecting DotbyDot displays the NORMAL screen.
TIPS
• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be careful.
• When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
• When dual-screen display is selected, the screen size cannot be changed.
• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original image (e.g. TV broadcast or video input from external equipment).
• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to “NORMAL”.
• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
• Depending on the original image size, black bands may remain at the edges of the screen.
Displays the entire image of the aspect ratio of 4:3 without changing the aspect ratio.
corresponding dots on the screen. *
Displays the dots of the input signals as the corresponding dots on the screen.
E
16
Menu Items
MENU
1 0 2 4 x7 6 8
V: 60 Hz H: 48.4 kHz
AUTO
CLOCK
PHASE
H-POS
V-POS
RESET
SCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
127
31
150
31
SCREEN PC2 ANALOG1/1
END…[MENU]
AUTO
CONTRAST
BLACK LEVEL
SHARPNESS
30
96
12
PC2 ANALOG1/2
PICTURE
SCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
OK…[MENU]
1 0 2 4 x7 6 8
V:
60 Hz H: 48.4 kHz
AUTO
CONTRAST
BLACK LEVEL
SHARPNESS
40
96
12
PC2 ANALOG1/2
PICTURE
SCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
OK…[MENU]
1 0 2 4 x7 6 8
V:
60 Hz H: 48.4 kHz
MENU
MENU
AUTO
CONTRAST
BLACK LEVEL
SHARPNESS
30
96
12
PC2 ANALOG1/2
PICTURE
SCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
OK…[MENU]
1 0 2 4 x7 6 8
V:
60 Hz H: 48.4 kHz
4
1 3 2
Displaying the menu screen
Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 18 to 20 for details of each menu items.
Example of operation
(Adjusting CONTRAST in the PICTURE menu)
1. Press
2. Press or to select PICTURE, and press .
PICTURE menu is displayed.
3. Press
to display the menu screen.
to select CONTRAST.
or
Menu screen display
1 Name of the menu 2 Input mode 3 An item being selected (highlighted) 4 Screen resolution of input signal, and other data.
TIPS
• Items that cannot be selected appear in gray. (e.g. Function not supported by the current input signal)
4. Press or to adjust the setting.
For items that have , press , make settings and then press
5. Press
TIPS
.
twice to close the menu screen.
• The menu will differ depending on the input mode.
• The menu screen will close automatically if no operation is performed for about 15 seconds. (DATE/TIME SETTING and SCHEDULE screens will close in about 4 minutes.)
17
E
MENU
MENU
MENU
MENU
Menu Items
Menu item details
The menu will differ depending on the input mode.
SCREEN (PC2/PC3)
AUTO
The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted.
Pressing Use this automatic adjustment when you use the PC2 input terminal or PC3 input terminals to display a PC screen for the first time or when you change the setting of the PC. (See page 22.)
CLOCK
Adjusts frequency for sampling clock for applicable video. Adjust when there is flickering in the form of vertical stripes. When using the adjustment pattern (see page 22), make adjustments so that no vertical stripe noise appears in it.
PHASE
Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/ or there are flickers at corners. When using the adjustment pattern (see page 22), make adjustments so that no horizontal stripe noise appears in it.
* Adjustments to PHASE should be made only after CLOCK
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
RESET
Resets the values of the SCREEN menu items to the factory preset values.
Select “ON” and then press
performs adjustment.
has been correctly set.
.
COLOR MODE
Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See page 15.) * sRGB is PC input only. See page 15 for details.
WHITE BALANCE
THRU .............. Displays the input signal level as is.
(for PC1 only)
PRESET ......... Selects the color temperature using PRESET.
USER .............. Used for adjusting R-CONTRAST,
G-CONTRAST, and B-CONTRAST
respectively.
PRESET
Selects the color temperature when the WHITE BALANCE is set to PRESET.
R-CONTRAST
Adjusts red component when the WHITE BALANCE is set to USER.
G-CONTRAST
Adjusts green component when the WHITE BALANCE is set to USER.
B-CONTRAST
Adjusts blue component when the WHITE BALANCE is set to USER.
COPY TO USER
Copies the value set for PRESET to the USER setting. Select “ON” and then press
GAMMA
Select a gamma value.
RESET
Resets the values of the PICTURE menu items to the factory preset values.
Select “ON” and then press
.
.
PICTURE
AUTO (PC2/PC3)
The CONTRAST and BLACK LEVEL are automatically adjusted.
Pressing
CONTRAST
Adjusts the brightness of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT (AV input)
Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.
COLORS (AV input)
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 22.)
performs adjustment.
AUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values. Select “ON” and then press
SETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
.
E
18
PATTERN 1 PATTERN 2
PATTERN 4PATTERN 3
STANDARD MIRROR
ROTATEUPSIDE DOWN
ABC
ABC
ABC
ABC
Menu Items
SCREEN MOTION
Residual images are reduced by moving the screen.
PATTERN 1 ....
PATTERN 2 .... A black screen spreads from the bottom of
PATTERN 3 .... A black bar moves from the left end to the
PATTERN 4 ....
MOTION TIME 1
Specify a time period (operating interval) until SCREEN MOTION starts.
MOTION TIME 2
Specify a time period during which SCREEN MOTION operates (time period during which the screen will move).
MONITOR
Select the installation direction of the monitor.
LANDSCAPE ............Horizontal orientation
PORTRAIT ...............
LANGUAGE
Sets the display language for the menu screen.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain (see page 25), using RS-232 cables. The numbers 1 to 255 are available for ID numbers. If “0” is set, the system regards this as the state where no ID number is set.
PICTURE FLIP
A picture flips to appear.
The whole screen moves vertically and horizontally.
the screen and then shrinks to the bottom of the screen. If the monitor is installed in the vertical orientation, a black screen spreads from the left end of the screen and then shrinks to the left end of the screen.
right end of the screen. If the monitor is installed in the vertical orientation, a black bar moves from the top to the bottom of the screen. Black screens appear from both the top and bottom of the screen, and the displayed image is compressed into the central field. If the monitor is installed in the vertical orientation, the screen is compressed from the left and right ends.
Vertical orientation
POWER ON DELAY
You can delay the screen display after the monitor is turned on. The period can be set up to 60 seconds in units of one second. When this function is activated, the power LED flashes (at approx. 1 second interval) in orange. This function is disabled when 0 is specified.
OPTION
DATE/TIME SETTING
Set the date and time. Press or to select the date and time, and press or to change the numerical values. Set the date in “Year/Month/Day” order.
Set the time on a 24-hour basis.
SCHEDULE (See page 21.)
You can set the time to switch the monitor on and off.
DVI SELECT
Selects equipment that is to be connected to the PC1/AV1 input terminal.
BNC SELECT
Selects equipment that is to be connected to the PC3/AV2 input terminals.
QUICK SHOOT
Reduces the visual lag inherent in fast-motion scenes.
COLOR SYSTEM
Select the color system of the AV equipment which is connected to AV3 input terminal. (AUTO / PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43) When AUTO is selected, the color system is automatically set according to the input signal.
AUDIO OUTPUT
Sets the volume of sound output from the PC/AV audio output terminals.
VARIABLE ..........
FIXED .................Fixes the sounds.
480LINES (PC2/PC3)
If a computer connected to the PC2/PC3 input terminal has a resolution of 640 x 480 or 848 x 480, make a selection according to the resolution.
768LINES (PC2/PC3)
If a computer connected to the PC2/PC3 input terminal has a resolution of 1024 x 768, 1280 x 768 or 1360 x 768, make a selection according to the resolution.
SELF ADJUST
On a PC2/PC3 screen with a resolution of 800 x 600 or higher, specify whether to perform screen adjustment automatically or not. When ON is selected, the screen is automatically adjusted when the timing of input signals varies. “ADJUSTING” appears on the screen during the adjustment.
POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal standby mode when the PC screen is displayed.
AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, AUTO INPUT CHANGE automatically changes the selected mode to another mode where a video signal is present. When video signals exist in multiple input modes, the switching priority is as follows: PC1, PC2, PC3, AV1, AV2 and AV3.
You can adjust the volume using VOLUME.
19
E
Menu Items
Main screen
Sub
screen
Main
screen
Sub
screen
Main screen
Sub
screen
ENLARGE (PC input)
ENLARGE MODE
Sets the number of screen splits used for the enlargement. (See page 21.)
ENLARGE POS
Specify the split screen to be displayed when the enlargement function is used. (See page 21.)
BEZEL H / BEZEL V
Sets the frame width of the display when the enlargement function is used.
H-POS
Adjust the horizontal position of the enlarged screen.
V-POS
Adjust the vertical position of the enlarged screen.
PIP/PbyP
PIP MODES
Sets the display method.
OFF .........Displays one screen.
PIP ...........Displays a sub screen inside a main screen.
PbyP ........Displays a main screen and a sub screen in a line.
PbyP2 ......Displays a main screen which measures 1280
pixels in the longest direction and a sub screen in a line.
PIP SIZE
Sets the size of the sub screen in PIP mode.
PIP H-POS
Adjusts the horizontal position of the sub screen in PIP mode.
PIP V-POS
Adjusts the vertical position of the sub screen in PIP mode.
PIP BLEND
In PIP mode, use this menu item to display the sub screen transparently.
PIP SOURCE
Selects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.
SOUND CHANGE
Sets the sound which is output in PIP, PbyP, or PbyP2 mode. If the main screen is displayed as a full screen by the AUTO OFF function, the sound for the main screen is output even when the sound for the sub screen is specified.
MAIN POS
Sets the position of the main screen in PbyP or PbyP2 mode.
PbyP2 POS
Sets the position of the sub screen in PbyP2 mode.
AUTO OFF
Sets the display method when no signals for the sub screen are input in PIP, PbyP, or PbyP2 mode.
MANUAL ....... Displays a main screen and a black sub
screen.
AUTO ............
Displays the main screen as a full screen.
TIPS
• When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST and GAMMA cannot be set.
• If COLOR MODE is set to sRGB or VIVID, the following items cannot be set. WHITE BALANCE, PRESET, R-/G-/B-CONTRAST, COPY TO USER, and GAMMA
Dual screen display
You can display the screens of the PC input signal and AV input signal simultaneously. Set this function with “PIP MODES” in the PIP/PbyP menu.
PIP
PbyP
PbyP2
* The currently selected input signal is displayed on the main
screen.
* You cannot simultaneously display the screens of signals
of the same type, such as two types of PC input signals or two types of AV input signals.
TIPS
• You might infringe on a copyright of the author which is protected by copyright law when you display the images of the computer screen and television/VCR simultaneously for profit-making or to show the image to the public.
• The screen size for dual-screen display is the same as the screen size for single-screen display. The DotbyDot screen is displayed in NORMAL size except when it is set as the PIP main screen.
• When dual-screen display is selected, the SCREEN MOTION function is disabled.
• When dual-screen display is selected, the AUTO INPUT CHANGE function is disabled.
• When dual-screen display is selected, the screen cannot be enlarged.
• When dual-screen display is selected, the following adjustments of ADVANCED are invalid and adjusting is disabled. 3D-NR, MPEG-NR and 3D-Y/C
A sub screen is displayed inside a main screen.
A main screen and a sub screen are displayed in a line.
Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line.
E
20
Menu Items
1
3
0
2
0
1 2
4 5 6
8
9 10
3
7
11
12
13
14
15
0 1
2
5 6 7
10
11 12
3
8
13
15 16 17 18
20
21
22 23
4
9
14
19
24
1
3
02
0
1
2
4
5
6
8
9
10
3
7
11
12
13
14
15
0
1
2
5
6
7
10
11
12
3813
15
16
17
18
20
21
22
23
491419
24
In horizontal orientation
In vertical orientation
0 1 2
3 4 5
6 7 8
0
1
2
3
4
568
7
Original
image
Original
image
4 monitors 9 monitors
16 monitors 25 monitors
4 monitors
9 monitors
16 monitors
25 monitors
SCHEDULE
No. POWER DAY OF THE WEEK TIME INPUT
XXXX/XX/XX XXX XX:XX:XX
PC2 ANALOG
(2)
OK
[MENU]
1 0 24x7 6 8
V: 60 Hz H: 48.4 kHz
(1)
(3) (4) (5)
MENU
Enlarge
You can align 4, 9, 16, or 25 monitors and integrate them into a single large screen to display. Enlarged views of separated images are displayed in each monitor.
TIPS
• AV input signals cannot be used for the Enlarge function.
• To integrate 9 or more monitors using PC1 signals, a splitter for the video signal (commercially available) is required.
• When connected in PC2/PC3, a splitter for the video signal (commercially available) is required.
• When Enlarge is used, the SCREEN MOTION function is disabled.
• When Enlarge is used, the AUTO INPUT CHANGE function is disabled.
SCHEDULE
You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the OPTION menu. (See page 19.)
1. Press or to select the SCHEDULE number, and press .
2. Set the SCHEDULE. (See the description below.)
Press or to select items, and press or to change the setting.
3. Press
.
SCHEDULE becomes effective.
(1)
●: SCHEDULE effective
-
: SCHEDULE not effective
(2) POWER
ON : Switches the monitor on at the specified time. OFF : Switches the monitor off at the specified time and puts
the monitor in standby mode.
(3) DAY OF THE WEEK
Specifies the day of the week to execute the SCHEDULE. ONLY ONCE:
Executes the SCHEDULE once on the specified day. Specify the day of the week to execute the SCHEDULE.
EVERY WEEK:
Executes the SCHEDULE on the specified day of the week every week. Specify the day of the week to execute the SCHEDULE. Periodic setting such as “Monday through Friday” is also possible.
EVERY DAY:
Executes the SCHEDULE every day regardless of the day of the week.
(4) TIME
Specifies the time to execute the SCHEDULE. Set the time on a 24-hour basis.
(5) INPUT
Specifies the input mode at power-on. When not specifying, the screen at the previous power-off appears. Input modes displayed on “PC1/AV1” depend on DVI SELECT settings. Input modes displayed on “PC3/AV2” depend on BNC SELECT settings.
21
E
Menu Items
MENU
MENU
Caution
• Do not switch off the main power after setting the SCHEDULE.
• Specify the correct date and time. (See pages 14 and 19.) SCHEDULE does not function unless the date and time are specified.
• Check regularly that the set date and time are correct.
TIPS
• Up to 8 SCHEDULE items can be registered.
• Setting the SCHEDULE flashes the power LED alternately in red and orange in standby mode.
• A SCHEDULE that has a large number has precedence over that of a small number when schedules overlap.
ADVANCED items (AV input) (See page 18.)
FLESH TONE
Adjust the hue control.
3D-NR
Reduce the noise of playback images on video. Setting a higher level reduces more noise. However, it may cause blurring on an image.
MPEG-NR
Reduce block noise caused by digital compression.
3D-Y/C (AV3)
Specify whether to perform 3-dimension Y/C separation. If dot interference or cross-color is occurring in fast-motion scenes, selecting “OFF” may improve the image quality.
Adjustments for PC screen display
Automatic adjustment
When you use the PC2 input terminal or PC3 input terminals to display a PC screen for the first time, or when you change the setting of the PC, use the automatic screen adjustment.
1. Switch the input to PC2 or to PC3 and display the
adjustment pattern. (See the description below.)
2. Press menu.
3. Press
4. Press
The automatic adjustment is complete in several seconds.
5. Press
TIPS
• If the screen cannot be adjusted properly with one automatic adjustment, repeat the automatic adjustment two or three times. Try manual adjustment if necessary.
Screen display for adjustment
Before making adjustments in the SCREEN menu or PICTURE menu, display an image to brighten the entire screen. If you are using a Windows PC, use the adjustment pattern on the supplied CD-ROM.
Opening the adjustment pattern
1. Load the supplied CD-ROM into the computer’s CD­ROM drive.
2. Open the CD-ROM in [My Computer].
3. Double-click [Adj_uty.exe].
The adjustment pattern will appear. Adjust the screen automatically or manually.
and use or to display the SCREEN
and select “AUTO”.
.
twice to close the menu screen.
4. When adjustment is finished, press the [Esc] on the computer’s keyboard to quit the adjustment program.
5. Eject the CD-ROM from the CD-ROM drive.
TIPS
• If the display mode on the computer you are using is 65,000 colors, the color levels in the color pattern may appear differently or grayscale may appear to be colored. (This is due to the specifications of the input signal and is not a malfunction.)
E
22
Initialization (Reset)/Functional Restriction Setting
SIZE
OFF
ON
ON
UNLOCKE
D
FUNCTION
1/1
ALL RESET
ADJUSTMENT LOCK
OSD DISPLAY
LED
RS-232C
END…[MENU]
MENU
MENU
You can return the settings to their factory-preset values and restrict operations.
1. After pressing
for about 5 seconds, press ,
, , and in that order.
2. Select and set the items.
ALL RESET
Resets the settings to the factory default settings. Press , select “ON” and then press
.
After initialization, turn the main power switch off and then back on.
ADJUSTMENT LOCK
You can disable operations on the monitor and the remote control unit that use buttons. OFF ...Enables operation.
1 ........Disables all operations other than turning power
on/off and FUNCTION.
2 ........Only the FUNCTION operation is enabled.
Disables all operations other than FUNCTION (not even power on/off).
OSD DISPLAY
Hides/shows menus. The FUNCTION screen cannot be hidden.
ON ...........Displays the menus.
OFF .........Hides the menus.
LED
Specifies whether to light power LEDs.
ON ...........Lights power LEDs.
OFF .........Does not light power LEDs.
RS-232C
Specifies whether to allow control via RS-232C (see page 24).
LOCKED .............Disables control via RS-232C.
UNLOCKED........Enables control via RS-232C.
3. Press
to return to the normal screen.
E
23
Controlling the Monitor with a PC
RS-232 straight cable (commercially available)
To COM port
PC
RS-232C input terminal
RS-232 straight cables (commercially available)
First monitor
Second monitor
PC
To COM port
RS-232C output terminal
RS-232C input terminal
C1 C2 C3 C4 P1 P2 P3 P4
Return code
Command field
(4 prescribed
alphanumerical characters)
Parameter field
(4 character string comprised of:
0-9, +, -, space, ?)
You can control this monitor from a PC via RS-232C (COM port) on the PC. You can also connect multiple monitors via a daisy chain by using a PC. By assigning ID numbers to each monitor (see page 25), you can make input mode selection/adjustment or can check the status of a specific monitor.
PC connection
One-to-one connection with a PC
Connect with RS-232 straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the monitor.
Communication conditions
Set the RS-232C communication settings on the PC to match the monitor’s communication settings as follows:
Baud rate 9600 bps Data length 8 bits Flow control None Parity bit None
Stop bit
1 bit
Communication procedure
Command format
When a command is sent from the PC to the monitor, the monitor operates according to the received command and sends a response message to the PC.
Example: VOLM0030 VOLM
30
Daisy chain connection…
Connect with RS-232 straight cable between the PC’s COM port (RS-232C connector) and the RS-232C input terminal on the first monitor. Next, connect RS-232 straight cable to the first monitor RS-232C output terminal and to the second monitor’s RS-232C input terminal. Connect in the same way to the third and subsequent monitors. Up to 25 monitors can be connected. (Depending on the length of the cable used and the surrounding environment.)
Advanced operation
’s
* Be sure to input 4 characters for the parameter. Pad with
spaces (“ ”) if necessary. (“ ” is a return code (0DH, 0AH or 0DH)) Wrong : VOLM30 Right : VOLM 30
When inputting a negative value, specify a numerical value in three digits.
Example: AUTR-009
Do not use spaces for MPOS, DATE, and SC01 through SC08. Specify parameters using a specified number of characters.
Example: MPOS010097
If a command has “R” listed for “DIRECTION” in the “RS-232C command table” on page 28, the current value can be returned by using “?” as the parameter.
Example:
VOLM ? ? ? ?
30
* If an ID number (see page 25) has been assigned
(For example, ID number = 1)
VOLM ? ← 30 001
From PC to monitor (How much is current volume setting?)
From monitor to PC (Current volume setting: 30)
From PC to monitor From monitor to PC
E
24
O K
Return code (0DH, 0AH)
O K SPC 0 0 1
ID number of responding monitor
Space (20H)
Return code (0DH, 0AH)
R RE
Return code (0DH, 0AH)
R RE SPC 0 0 1
ID number
Space (20H)
Return code (0DH, 0AH)
IW TA
Return code (0DH, 0AH)
EC DKOL
Return code (0DH, 0AH)
VOLM0020 OK
INPS0001 WAIT OK
Interval of 100 ms or more
[Example]
ID number: 1 ID number: 2 ID number: 3 ID number: 4
[Example]
ID number: 3 ID number: 2 ID number: 4 ID number: 1
Controlling the Monitor with a PC
Response code format
When a command has been executed correctly
A response is returned after a command is executed.
* If an ID number has been assigned
When a command has not been executed
* If an ID number has been assigned
TIPS
• “ERR” is returned when there is no relevant command or when the command cannot be used in the current state of the monitor.
• If communication has not been established for reasons such as a bad connection between the PC and monitor, nothing is returned (not even ERR).
• If no monitor has been assigned the designated ID number (e.g. if the command IDSL0002 is used, but no monitor with ID number: 2 is found), no response is returned.
Communication interval
• After OK or ERR is returned, you must send the following commands.
To set a timeout for the command response, specify 10
seconds or longer.
• Provide an interval of 100 ms or more between the command response and the transmission of the next command.
Advanced operation
This section explains commands for daisy chain connection. The basic communication procedure is the same as in the “One-to-one connection with a PC” section.
ID numbers
You can assign a unique ID number to each monitor (see page 19). This allows you to control a particular monitor in a daisy chain of monitors. You can assign ID numbers either from the menu screen (using the remote control) or from the PC using RS-232 cable.
If execution of the command is taking some time
When the following commands are used, “WAIT” is returned. In this case, a value will be returned if you wait a while. Do not send any command during this period. No ID number is attached to WAIT response.
• Commands which return WAIT:
1. When repeater control is used
2. When an IDSL or IDLK command is used
3. When one of the following commands is used: RSET, INPS, ASNC, WIDE, EMAG, EPOS, PXSL, POWR, AGIN, MWIN, MWIP, MWPP, ESTG
When control via RS-232C is locked (to prevent use) using the operation lock function (see page 23)
If monitors are connected as shown above, you can execute commands like “Set the volume of the monitor with ID 4 to 20”.
When controlling monitors linked in a daisy chain by designating ID numbers, you should basically avoid any duplication of ID numbers. ID numbers do not have to be assigned in ascending order starting from the PC. They can also be connected as shown below.
25
E
ID number: 1 ID number: 2 ID number: 3 ID number: 4
[Example]
ID number: 1 ID number: 2 ID number: 3 ID number: 4
Controlling the Monitor with a PC
Commands for ID control
The command examples shown on this page assume the following connection and ID number set up.
IDST ......... A monitor receiving this command sets its own ID
number in the parameter field.
Example:
IDST0001 OK 001 ←
TIPS
The ID number of this monitor is set to 1.
You can automatically assign ID numbers by using the IDST command with the Repeater control (see “Repeater control” on page 27). For example, using the command “IDST001+” automatically sets the ID numbers, as shown below.
IDLK ........
The parameter of this command sets the ID number of the monitor. The monitor is subject to all subsequent commands.
Example:
IDLK0002
WAIT ← OK 002
VOLM0030
WAIT
Following commands are for the monitor with ID number: 2.
Searching for monitor with ID number: 2 Found monitor with ID number: 2
Sets volume of monitor with ID number: 2 to 30.*
Processing
OK 002
VOLM0020
Sets volume of monitor with ID number: 2 to 20.*
WAIT OK 002 IDLK0000 ← WAIT ← OK 002
Canceling fixed ID number setting Canceling IDLK Cancelation complete
VOLM0010
The volume of the monitor with ID number: 1
OK 001
(the one directly connected to the PC) is set to 10. (IDLK is canceled.)
* The IDLK command remains effective until it is
canceled, or power is shut off.
IDST001 +
ID setting command with repeater control
WAIT OK 001 ← OK 002 ← OK 003 ← OK 004
“OK” response from ID number: 1 “OK” response from ID number: 2 “OK” response from ID number: 3 “OK” response from ID number: 4 (End)
IDSL ........The parameter of this command sets the ID number
of the monitor. The monitor is subject to the next command.
Example:
IDSL0002
WAIT ← OK 002
VOLM0030
WAIT
OK 002
VOLM0020
OK 001
The next command is for the monitor with ID number: 2.
Searching for monitor with ID number: 2 Found monitor with ID number: 2
Sets volume of monitor with ID number: 2 to 30.
Processing OK response from monitor with ID
number: 2 Sets volume to 20. The volume of the monitor with ID
number: 1 (the one directly connected to the PC) is set to 20.*
* The IDSL command is effective only once, for the
immediately succeeding command.
IDCK ........Provides screen display of the ID number currently
assigned to a monitor, and the ID number currently set for IDLK (if any).
Example:
(After executing IDLK0002)
IDCK0000
ID : 001 IDLK : 002
IDCK000 + WAIT ID : 001 IDLK : 000 ID : 002 IDLK : 000 ID : 003 IDLK : 000 ID : 004 IDLK : 000
(Parameter has no meaning.)
Returned response. The ID number is also displayed on the
monitor screen. Repeater control (If a command
is used with repeater control, ID designation using IDSL or IDLK is canceled.)
E
26
Controlling the Monitor with a PC
[Example]
Set 1 Set 2 Set 3 Set 4
Repeater control
This system has a function to allow setting of multiple monitors connected in a daisy chain using a single command. This function is called repeater control. You can use Repeater control function without assigning ID numbers.
* If monitors are connected as shown above, you can
execute a command like “Set all monitors’ input settings to PC1 DIGITAL”.
Repeater control command
Repeater control is achieved by setting the FOURTH CHARACTER of the parameter to “+”.
Example:
VOLM030 +
In repeater control, responses are returned by all the connected monitors. If you want to determine that a value has been returned by a specific set, assign ID numbers to each monitor in advance. When some monitors do not return their responses, the probable cause is that the monitors could not receive the command or command processing is not complete. Do not send a new command.
Sets volume of all monitors to 30.
Example: (When 4 monitors are connected, and
assigned ID numbers: 1 through 4)
VOLM030 + WAIT OK 001 OK 002 OK 003 OK 004 ← If 4 monitors are connected in
a chain, reliable operation can be ensured by sending a new command only after a reply has been returned by 4th (last) monitor.
Repeater control can also be used for reading settings.
Example:
VOLM ? ? ? + WAIT 10 001 20 002 30 003 30 004
Volume settings for all monitors are returned.
TIPS
• If repeater control is used during ID designation (IDSL, IDLK), the ID designation is canceled.
• Commands that use parameters consisting of more than four characters can not be controlled by repeater control.
27
E
Controlling the Monitor with a PC
RS-232C command table
How to read the command table
Command: Command field (See page 24.) Direction: W When the “Parameter” is set in the parameter field (see page 24), the command functions as described
under “Control/Response Contents”.
R The returned value indicated under “Reply” can be obtained by setting “????”, “
(repeater control) in the parameter field (see page 24). Parameter: Parameter field (See page 24.) Reply: Response (Returned value) *: “Yes” indicates commands which can be used in power standby mode.
TIPS
• To specify the horizontal/vertical positions for vertical orientation, specify the values for horizontal orientation.
Power control/Input mode selection
Function
POWER CONTROL POWR W 0
INPUT MODE SELECTION
Command Direction
R 0 Standby mode
INPS W 0 Toggle change for input mode
R 1 PC1 DIGITAL
Parameter Reply Control/Response contents *
Switches to standby mode.
1 Returns from standby mode.
1 PC1 DIGITAL
2 PC2 ANALOG 3 AV2 COMPONENT
4 AV3 VIDEO 6 PC3 ANALOG
7 AV1 DIGITAL
1 Normal mode 2 Input signal waiting mode
Terminals not selected in DVI SELECT/BNC SELECT cannot be selected.
“ERR” when AV (DIGITAL) is selected for DVI SELECT.
“ERR” when PC (ANALOG) is selected for BNC SELECT.
“ERR” when AV (COMPONENT) is selected for BNC SELECT.
“ERR” when PC (DIGITAL) is selected for DVI SELECT.
2 PC2 ANALOG 3 AV2 COMPONENT 4 AV3 VIDEO 6 PC3 ANALOG 7 AV1 DIGITAL
?” or “???+”
Yes
Yes
SCREEN menu (PC2/PC3)
Function
AUTO CLOCK CLCK WR 0-255 0-255 PHASE PHSE WR 0-63 0-63 POSITIONING POSITION OF
RESET ARST W 1 No
E
28
THE LONGEST DIRECTION
POSITION OF THE SHORTEST DIRECTION
Command Direction
ASNC W 1 No
HPOS WR 0-500 0-500 A maximum value depends on a resolution.
VPOS WR 0-100 0-100
Parameter Reply Control/Response contents *
No
Controlling the Monitor with a PC
PICTURE menu
Function
AUTO CONTRAST CONT WR 0-60 0-60 0-127 on PC2/PC3. BLACK LEVEL BLVL WR 0-60 0-60 0-127 on PC2/PC3. TINT TINT WR 0-60 0-60 When the input mode is AV. COLORS COLR WR 0-60 0-60 SHARPNESS SHRP WR 0-24 0-24 ADVANCED FLESH TONE
3D-NR TDNR WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH MPEG-NR MPNR WR 0-1 0-1 0: OFF, 1: ON 3D-Y/C YCSP WR 0-1 0-1 0: OFF, 1: ON
COLOR MODE BMOD WR 0 0 STD
WHITE BALANCE THRU CTMP WR 0 0 When the input mode is PC1.
PRESET 1-15 1-15 From 1: approximately 3,000K to 15: approximately 10,000K
USER 99 99 R-CONTRAST CRTR WR 0-512 0-512 “ERR” when CTMP is not set to 99. G-CONTRAST CRTG WR 0-512 0-512
B-CONTRAST CRTB WR 0-512 0-512 GAMMA GAMM WR 0-2 0-2 0: 1.8, 1: 2.2, 2: 2.4 Yes RESET ARST W 2 No
Command Direction
AGIN W 1 When the input mode is PC2, PC3. No
FLES WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH
Parameter Reply Control/Response contents *
2 2 VIVID 3 3 sRGB (When the input mode is PC)
(500K steps)
AUDIO menu
Function
TREBLE AUTR WR
BASS AUBS WR
BALANCE AUBL WR
RESET ARST W 3 No
Command Direction
Parameter Reply Control/Response contents *
-10-10 -10-10
-10-10 -10-10
-10-10 -10-10
Yes
Yes
Yes
Yes
Yes
SETUP menu
Function
SCREEN MOTION SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN 1-4 Yes MOTION TIME 1 MOTION TIME 2 PATTERN 1
PATTERN 2-4 MONITOR LANGUAGE LANG WR 14 14 ENGLISH
ID NUMBER ID NO. SETTING IDST W 0-255 Sets the monitor’s ID number. (“0” means “no ID number”.)
ID NO. SETTING
(ONCE)
ID NO. SETTING
(SUBSEQUENT)
ID CHECK IDCK W 0 ID : xxx
PICTURE FLIP PFIL WR 0-3 0-3 0: OFF, 1: MIRROR, 2: UPSIDE DOWN, 3: ROTATE Yes Power On Delay PWOD WR 0 0 OFF
Command Direction
MTIM WR 0-20 0-20 Yes MINT WR 10-990 10-990 Per 10 seconds MINT WR 5-20 5-20 Per second STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT Yes
R 0-255 Returns the monitor’s ID number.
IDSL W 1-255 Sets a monitor ID number.
IDLK W 1-255 Sets a monitor ID number.
Parameter Reply Control/Response contents *
1 1 DEUTSCH 2 2 FRANÇAIS 3 3 ITALIANO 4 4 ESPAÑOL 5 5 РУССКИЙ 6 6
This ID number is only effective for the command immediately after this command.
0 Clears the ID number if one has been designated.
This ID number is effective for the next and all subsequent commands after this command.
0 Clears the ID number if one has been designated.
IDLK : yyy
1-60 1-60 ON
Displays monitor’s own ID number and the selected ID number on the screen.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
29
E
Controlling the Monitor with a PC
OPTION menu
Function
DATE/TIME SETTING DATE
SCHEDULE SC01-
DVI SELECT DVSL WR 0-1 0-1 0: PC (DIGITAL), 1: AV (DIGITAL) Yes BNC SELECT BNSL WR 0-1 0-1 0: PC (ANALOG), 1: AV (COMPONENT) Yes QUICK SHOOT (PC) QUICK SHOOT (AV) QSAV COLOR SYSTEM CSYS WR 0-5 0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC 3.58, 5: NTSC 4.43 Yes AUDIO OUTPUT AOUT WR 0-1 0-1 0: VARIABLE, 1: FIXED Yes INPUT
RESOLUTION (PC)
INPUT RESOLUTION (AV)
SELF ADJUST AADJ WR 0-1 0-1 0: OFF, 1: ON Yes POWER MANAGEMENT PMNG WR 0-1 0-1 0: OFF, 1: ON Yes AUTO INPUT CHANGE
RESOLUTION CHECK
PIXEL SETTING (PC2, PC3)
RESOLUTION CHECK
Command Direction
WR
SC08
QSPC WR 0-1 0-1 0: OFF, 1: ON Yes
PXCK R - Returns current resolution in the form of hhh, vvv.
PXSL WR 1 1 V: 768) 1360 x 768
RESO R - 480i, 480p, 1080i, 720p, 1080p, VGA, etc.
AINC WR 0-1 0-1 0: OFF, 1: ON Yes
WR ABCDEFFGGH ABCDEFFGGH Schedule of a specified number
WR 0-1 0-1 0: OFF, 1: ON Yes
Parameter Reply Control/Response contents *
AABBCCDDEE AABBCCDDEE
2 2 V: 768) 1280 x 768 3 3 V: 768) 1024 x 768 5 5 V: 480) 848 x 480 6 6 V: 480) 640 x 480
AA: Year, BB: Month, CC: Day, DD: Time, EE: Minute
A: Schedule 0 = Not effective, 1 = Effective B: Power 0 = OFF, 1 = ON C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day D: Day of the week 2 0 = Sunday, 1 = Monday through 6 = Saturday,
E: Day of the week 3 0 = Sunday, 1 = Monday through 6 = Saturday,
00-23
F: Time G: Minute 00-59 H: Input 0 = Not specified, 1 = PC1/AV1, 2 = PC2,
9 = Not exist
9 = Not exist
3 = PC3/AV2, 4 = AV3
Yes
Yes
No
No
ENLARGE menu (When the input mode is PC)
Function
ENLARGE MODE EMAG WR 0-4 0-4 0: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5 BEZEL WIDTH
IMAGE POSITION (2 x 2) EPOS WR 0-3 0-3 See page 21. IMAGE POSITION (3 x 3) EPOS WR 0-8 0-8 IMAGE POSITION (4 x 4) EPOS WR 0-15 0-15 IMAGE POSITION (5 x 5) EPOS WR 0-24 0-24 ENLARGED
SCREEN POSITIONING
ENLARGE/IMAGE POSITION SETTING ESTG WR XXYY XXYY XX: ENLARGE MODE (Same as EMAG), YY: IMAGE POSITION (Same
WIDTH OF THE SHORTER
WIDTH OF THE LONGER SIDE
THE LONGEST DIRECTION
THE SHORTEST DIRECTION
Command Direction
BEZH WR 0-100 0-100
SIDE
BEZV WR 0-100 0-100
EPSH WR -999-999 -999-999 The setting range depends on the ENLARGE MODE setting and the
EPSV WR -999-999 -999-999
Parameter Reply Control/Response contents *
IMAGE POSITION.
as EPOS)
PIP/PbyP menu
Function
PIP MODES PIP SIZE PIP POS THE LONGEST
PIP V/H-POS
PIP BLEND PIP SOURCE
SOUND CHANGE MWAD WR 1-2 1-2 1: MAIN, 2: SUB Yes MAIN POS (Main screen) MWPP WR 0-1 0-1 0: POS1, 1: POS2 Yes PbyP2 POS (Sub screen) MW2P WR 0-2 0-2 0: POS1, 1: POS2, 2: POS3 Yes AUTO OFF
DIRECTION
THE SHORTEST DIRECTION
Command Direction
MWIN WR 0-3 0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2 Yes MPSZ WR 1-12 1-12 Yes MHPS W 0-100 Yes
R 0-100 Yes
MVPS W 0-100 Yes
R 0-100 Yes
MPOS W 0-100,0-100 Specify the position in MPOSxxxyyy format.
R 0-100,0-100 Returns a response in (xxx,yyy) format.
MWBL WR 0-15 0-15 Yes MWIP WR 1 1 PC1 DIGITAL
MOFF WR 0-1 0-1 0: MANUAL, 1: AUTO Yes
Parameter Reply Control/Response contents *
(xxx: Longer side, yyy: Shorter side position)
(xxx: Longer side, yyy: Shorter side position)
2 2 PC2 ANALOG 3 3 AV2 COMPONENT 4 4 AV3 VIDEO 6 6 PC3 ANALOG 7 7 AV1 DIGITAL
No
Yes
Yes
Yes
E
30
Controlling the Monitor with a PC
Initialization/Functional Restriction Setting (FUNCTION) menu
Functio
ALL RESET ADJUSTMENT LOCK OSD DISPLAY LED OFLD WR 0-1 0-1 0: ON, 1: OFF Yes
Command Direction
RSET W 0 No ALCK WR 0-2 0-2 0: OFF Yes LOSD WR 0-1 0-1 0: ON, 1: OFF Yes
Parameter Reply Control/Response contents *
Others
Function
SCREEN SIZE (PC) WIDE WR 1-5 1-5 1: WIDE, 2: NORMAL, 3: DotbyDot, 4: ZOOM1, 5: ZOOM2 Yes SCREEN SIZE (AV) VOLUME VOLM WR 0-31 0-31 Yes MUTE MUTE WR 0-1 0-1 0: OFF, 1: ON No INFORMATION
BRIGHT VLMP WR 0-31 0-31 Brightness Yes TEMPERATURE SENSOR DSTA
TEMPERATURE ACQUISITION ERRT
CAUSE OF LAST STANDBY MODE
MODEL INF1 R Value SERIAL NO
Command Direction
WIDE WR 1-5 1-5 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: DotbyDot Yes
SRNO R Value
R 0 Internal temperature normal
R Value Temperature at temperature sensors 1 through 3 are returned in the
STCA W 0 Initialization
R 0 No detectable error has occurred
Parameter Reply Control/Response contents *
1 Internal temperature abnormal (Standby mode) 2 Internal temperature abnormal (Temperature is normal now, but it was
abnormal during operation.) 3 Internal temperature abnormal (Brightness of the backlight decreases.) 4 Temperature sensor abnormal
following forms:
[Sensor 1], [Sensor 2], [Sensor 3]
1 Standby mode by POWER button 2 Main power “OFF” by the main power switch 3 Standby mode by RS-232C 4 Waiting mode by No Signal (Incl: VESA DPMS/DMPM) 6 Standby mode by abnormal temperature 8 Standby mode by SCHEDULE setting
Yes
Yes
Yes
Yes
31
E
Troubleshooting
Before calling for repair services, make sure following checks for possible remedies to the encountered symptoms.
There is no picture or sound.
• Is the power cord disconnected? (See page 12.)
• Is the main power switch set to “OFF”? (See page 14.)
• Is the monitor in standby mode (the power LED illuminating in orange)? (See page 14.)
• Make sure correct input mode is selected. (See page 15.)
• If any external equipment is connected, make sure the equipment is operating (playing back).
Remote control does not work.
• Are the batteries inserted with polarity (+,-) aligned? (See page 13.)
• Are the batteries exhausted? (See page 13.)
• Point the remote control unit toward the monitor’s remote control sensor. (See page 13.)
• Is the menu display hidden or is operation disabled? (See page 23.)
Sound from left and right speakers is reversed. Sound is heard from only one side.
• Are audio cables connected properly? (See pages 10 and
11.)
• Make sure audio cables for external speakers are connected properly: left and right cables may be reversed or one of the two cables may not be connected. (See page
11.)
• Check the setting of BALANCE for AUDIO menu. (See page 18.)
There is a picture but no sound.
• Is the sound muted? (See page 15.)
• Make sure the volume is not set to minimum. (See page
15.)
• Is the PC audio cable (commercially available) connected? (See page 10.)
• Are audio cables connected properly? (See page 10.)
• Is the audio signal input properly to the audio input terminal corresponding to the selected video input terminal? (See page 15.)
Unstable video.
• The signal may be incompatible. (See pages 10 and 34.)
• Try the automatic screen adjustment when the PC2 input terminal or PC3 input terminals is used. (See page 22.)
PC1 or AV1 does not appear properly.
• Is the setting of DVI SELECT correct? (See page 19.)
• Is the input signal compatible with this monitor? (See pages 10 and 34.)
• Turn off the power to the connected equipment and then turn the power on again.
• If the monitors are connected in a daisy chain, turn off the power to all the monitors connected in a daisy chain and then turn the power on again.
Control buttons do not work. There is no picture.
• Some kind of load noises from outside might interfere with normal operation. Turn off the power and turn it on after waiting at least 5 seconds, and then check the operation.
The input mode changes automatically.
• When the AUTO INPUT CHANGE is ON and no signal is present in a selected input mode, the AUTO INPUT CHANGE automatically changes the selected mode to a mode where a video signal is present. (See page 19.) The input mode may change in the following cases:
- When a computer is in standby mode.
- When video play is stopped with a playback device.
Power LED flashes red. “SERVICE CALL” appears in the corner of the screen.
• Hardware has a problem. Turn off the monitor and request repair from your SHARP dealer.
When “TEMPERATURE” is displayed.
• When the internal temperature of the monitor rises excessively, the brightness of the backlight decreases in order to prevent high-temperature-related problems. Remove the cause of the excessive rise in temperature. (See the description below.)
The monitor sometimes makes a cracking sound.
• You may hear cracking sound from the monitor. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the monitor’s performance.
■ Warning when temperature rises
• When the internal temperature of the monitor rises excessively, the brightness of the backlight decreases automatically in order to prevent high-temperature­related problems. When this occurs, “TEMPERATURE” is displayed on the screen and the Power LED flashes red and green alternately.
• If the internal temperature rises further, the monitor automatically enters standby mode. (The Power LED continues flashing red and green alternately.)
Solution:
• If the monitor enters standby mode due to a rise in temperature, to return to normal display, turn the main power switch off and then back on again. The monitor, however, will enter standby mode again if the cause of the temperature rise is not eliminated. (See page 9.)
• Check whether the monitor is placed at a location where a quick rise in temperature is likely. Internal temperature rises quickly if the vents on the monitor are blocked.
• Internal temperature rises quickly if dust accumulates inside the monitor or around the vents. Remove dust if possible. Ask Sharp dealer about removing internal dust.
PC3 or AV2 does not appear properly.
• Is the setting of BNC SELECT correct? (See page 19.)
• Is the input signal compatible with this monitor? (See page
34.)
E
32
Specifications
Product Specifications
Model PN-525U LCD element 52" wide (132.2 cm diagonal) ASV low-reflection black TFT LCD Max. resolution (pixels) 1920 x 1080 Max. colors 16.77 M colors (8 bits/color) Pixel pitch 0.600 mm (H) x 0.600 mm (V) Vi
ewing angle 176° right/left/up/down (contrast ratio ≥ 10) Screen active area inch (mm) 45-3/8 x 25-1/2 (1152.0 x 648.0) Computer input signal Digital (DVI 1.0 standard-compliant), Analog RGB (0.7Vp-p) [75 ] S Composite sync (TTL: positive/negative) Vi
deo color system PAL, PAL-60, SECAM, NTSC (3.58 MHz), NTSC (4.43 MHz) Plug and play VESA DDC2B Power management VESA DPMS, DVI DMPM Input terminals PC/AV Digital DVI-D 24 pin (HDCP compatible) x 1
AV
Output terminals PC/AV Digital DVI-D 24 pin x 1 Audio RCA pin (L/R) x 1
Power requirement AC 120 V, 60 Hz Operating temperature 32°F to 104°F (0°C to 40°C) Operating humidity 20% to 80% (no condensation) Power consumption 325 W (Input signal waiting mode: 11.5 W*4, Standby mode: 3.5 W) Dimensions inch (mm) Approx. 49-3/8 x 5-7/8 x 29-3/16 (1,254 x 149 x 742) (excluding protrusions) Weight lbs. (kg) Approx. 97.0 (44) (excluding the temporary stand)
ync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green,
PC Analog Mini D-sub 15 pin, 3 rows x 1, BNC Audio 3.5 mm mini stereo jack x 1
Composite video BNC x 1 Component BNC (Y, Cb/Pb, Cr/Pr)*1 x 1 Audio RCA pin (L/R) x 1 Serial (RS-232C) D-sub 9 pin x 1
*3
Serial (RS-232C) D-sub 9 pin x 1 Speaker 7 W + 7 W [6 ]
*1*2
x 1
*1 Cannot be used simultaneously. *2 Does not support plug and play. *3 Connection is allowed with an HDCP-compatible device only. Does not support Repeater control function. *4 When AUTO INPUT CHANGE is ON. 7.5 W when it is OFF.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product imporovement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units
.
33
E
VESA
Wide
US TEXT Sun
Screen resolution Hsync Vsync Dot frequency
Analog signal
640 x 480
800 x 600
848 x 480
1024 x 768
11
52 x 864
1280 x 768
1280 x 960
1280 x 1024
1360 x 768
1600 x 1200
*1
1280 x 720
1920 x 1080
720 x 400
1024 x 768
11
52 x 900
1280 x 1024
1600 x 1000
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
31.0 kHz
48.4 kHz
56.5 kHz
60.0 kHz
67.5 kHz
47.8 kHz
60.3 kHz
60.0 kHz
64.0 kHz
80.0 kHz
47.7 kHz
75.0 kHz
44.7 kHz
66.3 kHz
31.5 kHz
48.3 kHz
53.6 kHz
56.6 kHz
61.8 kHz
71.8 kHz
71.7 kHz
81.1 kHz
68.6 kHz
60 Hz 72 Hz 75 Hz 56 Hz 60 Hz 72 Hz 75 Hz 60 Hz 60 Hz 70 Hz 75 Hz 75 Hz 60 Hz
75 Hz 60 Hz 60 Hz 75 Hz 60 Hz 60 Hz 60 Hz 60 Hz 70 Hz 60 Hz 66 Hz 70 Hz 66 Hz
76.2 Hz
67.2 Hz 76 Hz 66 Hz
25.175 MHz
31.5 MHz
31.5 MHz
36.0 MHz
40.0 MHz
50.0 MHz
49.5 MHz
33.75 MHz
65.0 MHz
75.0 MHz
78.75 MHz
108.0 MHz
79.5 MHz
102.25 MHz
108.0 MHz
108.0 MHz
135.0 MHz
85.5 MHz
162.0 MHz
74.4 MHz
148.5 MHz
28.3 MHz
64.13 MHz
70.4 MHz
74.25 MHz
94.88 MHz
108.23 MHz
117.01 MHz
134.99 MHz
135.76 MHz
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Digital signal
Yes Ye
s
Ye
s
­Yes Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
-
-
-
-
-
-
-
-
*1 Displays a reduced image.
Unit: inch [mm]
49-3/8 [1254]
Opening width (45-9/16 [1157])
34-3/4 [882]
Opening height
(25-11/16 [653])
29-3/16 [742]
7-7/8
[200]
10-11/16
[271]
5-7/8 [149]
3-5/8
[92]
3-3/4 [95] 2-5/8 [66]
7-7/8
[200]
7-7/8
[200]
7-7/8 [200]
VESA holes
Specifications
Dimensional Drawings
Note that the values shown are approximate values.
When mounting the monitor, be sure to use a wall-mount / ceiling-mount bracket they comply with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose holding may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use the bracket which applied UL1678 standard, and which can endure at least 3 times or more the weight of the monitor.
Compatible signal timing (PC)
* All are compliant only with non-interlaced. * Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input. * The frequency values for the Sun are reference values. A separate conversion adapter (commercially available) may be required for
connecting the monitor to the Sun.
E
34
Specifications
No.
1 2 3 4 5 6 7 8
9 10 11 12
Function
TMDS data 2­TMDS data 2+ TMDS data 2/4 shield N.C. N.C. DDC clock DDC data N.C. TMDS data 1­TMDS data 1+ TMDS data 1/3
shield
N.C.
No.
13 14 15 16 17 18 19 20 21 22 23 24
Function
N.C. +5 V GND Hot-plug detection TMDS data 0­TMDS data 0+ TMDS data 0/5 shield N.C. N.C. TMDS clock shield TMDS clock+ TMDS clock-
No.
1
2
3
4
5
Function
N.C. Transmitted data Received data N.C. GND
No.
6 7 8 9
Function
N.C. N.C. N.C. N.C.
No.
1
2
3
4
5
Function
N.C. Received data Transmitted data N.C. GND
No.
6 7 8 9
Function
N.C. N.C. N.C. N.C.
No.
1
2
3
4
5
6
7
8
Function
Red video signal input Green video signal input Blue video signal input N.C. GND GND for red video signal GND for green video signal GND for blue video signal
No.
9 10 11 12 13 14 15
Function
+5 V GND N.C. DDC data Hsync signal input Vsync signal input DDC clock
No.
1 2 3 4 5 6 7 8
9 10 11 12
Function
TMDS data 2­TMDS data 2+ TMDS data 2/4 shield N.C. N.C. DDC clock DDC data N.C. TMDS data 1­TMDS data 1+ TMDS data 1/3
shield
N.C.
No.
13 14 15 16 17 18 19 20 21 22 23 24
Function
N.C. +5 V GND Hot-plug detection TMDS data 0­TMDS data 0+ TMDS data 0/5 shield N.C. N.C. TMDS clock shield TMDS clock+ TMDS clock-
DPMS
ON STATE
STANDBY SUSPEND
OFF STATE
Screen
Display
No
display
Power
consumption
325 W
11
.5 W*
Hsync
Ye
s
No
Ye
s
No
Vsync
Ye
s
Ye
s No No
DMPM
Monitor ON Active OFF
Screen
Display
No display
Power
consumption
325 W
11
.5 W*
Power management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.
DPMS: Display Power Management Signaling DMPM: Digital Monitor Power Management
* When AUTO INPUT CHANGE is ON. 7.5 W when it is
OFF.
DDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect plug-and-play monitors. There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.
PC1/AV1 input terminal pins
(DVI-D24 pin)
PC2 input terminal pins
(Mini D-sub 15 pin)
RS-232C input terminal pins
(D-sub 9 pin)
RS-232C output terminal pins
(D-sub 9 pin)
PC/AV output terminal pins
(DVI-D24 pin)
35
E
M E M O
E
36
Loading...