Sharp PC-MM1 User Manual

NOTEBOOK COMPUTER
 
 
6 6
1 1

Notice for Users in the USA

FCC Statement
WARNING - FCC Regulations state that any unauthorized changes or modifications to these equipments not expressly approved by the manufacturer could void the user’s authority to operate these equipments.
Note: These equipments have been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. These equipments generate, use and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If these equipments do cause harmful interference to radio or television reception, which can be determined by turning the equipments off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
A shielded I/F cable is required to insure compliance with FCC regulation for Class B computing equipment.
* As an ENERGY STAR
the ENERGY STAR
Declaration of Conformity
SHARP PERSONAL COMPUTER, PC-MM Series This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 TEL: 1-800-BE-SHARP
®
Partner, SHARP has determined that this product meets
®
guidelines for energy efficiency.
i
For Wireless LAN Bundled Model
Wireless LAN Model Name: T60H42400 FCC ID: MCLT60H42400
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org
Copyright
It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
Product Information and Customer Assistance
For Product Information and Customer Assistance: Call: 1-800-BE-SHARP (237-4277) Sharp Systems of America 5901 Bolsa Avenue, Huntington Beach, CA 92647 Home Page: http://www.sharpsystems.com
E-mail address: support@sharpsystems.com
ii
CAUTION:
TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING.
CAUTION:
FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY.
VORSICHT:
UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN.
ATTENTION:
POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE.
VARNING:
FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH TA UR BATTERIET.
PRECAUCION:
PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED Y LA BATERIA.
iii

Safety Precautions

General
Follow all cautions and instructions, which may be marked, on the computer.
Except as described elsewhere in this manual, refer all servicing to qualified
personnel. Immediately shut off the computer and seek servicing under the following conditions:
when the power cord or plug is damaged or frayed
when liquid has been spilled on the computer
when the computer has been dropped or the cabinet has been damaged
Location
Do not expose the computer to direct sunlight.
Try to avoid dusty environments.
Keep the computer away from any magnetic devices and TVs.
Keep the computer away from excessive humidity or fluids such as rain, snow,
water spray, juice, coffee, steam, etc.
Do not move the computer from an extremely cold place to an extremely warm
place. A temperature difference of more than 10°C (18°F) will cause condensation inside the unit, which may cause damage.
Do not block or cover slots or openings on the cabinet. These protect the computer
from overheating.
Do not place the computer on unstable or uneven work surfaces.
Do not use the computer on your lap or any part of your body for an extended
period during operation or charging to avoid injury from heat exposure.
Usage
Never push any objects of any kind into cabinet openings. They may touch
dangerous voltage points or short parts that could result in fire or electrical shock.
Turn off the computer before installing or removing peripheral devices (except
when connecting USB devices and PC cards, etc.).
Check the AC power cord and power connectors periodically for damage. Replace
the power cord immediately if damage is found.
Never subject your computer to sudden shocks or extreme vibration.
iv
Do not drop the computer nor hit it with other equipment.
Do not scratch the surface of the LCD screen.
Turn off the computer and disconnect the AC power cord before cleaning.
Battery Precautions
CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
Handling
Never put the battery pack in a fire, as it could explode and cause injury.
Do not attempt to open or alter the battery pack.
Do not place the battery where it might get hotter than 60°C (140°F).
Do not allow metal objects such as jewelry to short across the battery terminals, as
it could heat up and explode.
Do not allow liquids to come in contact with the battery pack.
Avoid dropping the pack or other violent shock.
Do not solder anything to the battery terminals.
v
Charging
Charge the battery pack only with the AC adapter included with your computer.
Discharging
Do not use the battery pack for any purpose other than powering your computer.
Storage
Store the battery pack in a cool and dry place. Never allow the temperature to
exceed 60°C (140°F) during storage.
Recharge the stored battery pack after storage, before use.
Wireless LAN Precautions
Disable the integrated antenna and do not communicate with wireless LAN in
specific environment where radio-susceptible equipment is nearby such as on airplanes, in hospitals, etc.
Do not communicate with wireless LAN in the following environment:
where radio-frequency generating devices are nearby such as microwaves,
wireless applications, etc.
where metallic materials are nearby such as steel cabinets, etc.
vi
Caution
Your computer is integrated with a magnet on the right side of the display. Be sure to keep the magnetic cards or floppy disks away from the right side of your computer. Otherwise the data on the cards or floppy disks may be erased. This computer has a sensor on the right side of the keyboard which responses to the magnet. If you bring the magnet near the right side of the keyboard, the backlight is turned off, and the system may enter the standby or the hibernate mode depending on the setting. (See Chapter 3.)
Magnet
vii

About This Manual

Notice
Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation and its sales subsidiaries.
SHARP Corporation and its sales subsidiaries shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other causes.
SHARP assumes no responsibility directly or indirectly, for financial losses or claims from third persons resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss of or alteration of stored data, etc.
Edition
1st Edition, March 2003.
Copyright
© 2003 SHARP Corporation This document contains or refers to proprietary information which is protected by copyright. All rights are reserved. Copying or other reproduction of this document is prohibited without the prior written permission of SHARP Corporation.
Trademarks
Crusoe is a trademark of Transmeta Corporation. IBM is a trademark of International Business Machines Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries.
Power Quest is a registered trademark and EasyRestore is a trademark of PowerQuest Corporation.
BAPCo is a registered trademark of the Business Applications Performance Corporation. MobileMark is a trademark of the Business Applications Performance Corporation.
All other brand and product names are trademarks or registered trademarks of their respective holders.
viii

Recording Important Information

For future reference, please record the following information in the spaces provided below.
Model Number:
Serial Number:
Date of purchase:
Dealer’s Name:
Place of purchase:
Password:
The serial number is printed on a sticker located on the bottom of the computer.
ix

Manual Conventions

This manual uses a set of style conventions described below.
Notes and Cautions are italicized with icons:
A note icon informs you of a special technique or information that may help you perform a task or better understand a process.
A caution icon alerts you to something that may cause problems or damage to hardware, software or data.
Key Labels on the Keyboard, when referred to in the instructions, are shown in boldface: Press Enter to continue.
When two or more keys are pressed simultaneously, the key labels are separated by a plus (+) sign: Run Task Manager by pressing Ctrl+Alt+Delete.
Sample Entries are shown in lower cases of different typeface.
c:\windows\system
Words/Texts on Screen, such as window titles or possible parameters, are italicized:
Double-click this icon to display the Power Options Properties dialog box. Set the item to Enabled.
Screens reproduced in this manual may differ slightly from the screens you see on your computer.
Section Titles in other parts of this manual are italicized:
Refer to Installing Battery Pack section of Chapter 1.
x

Table of Contents

Notice for Users in the USA....................................................................................... i
Safety Precautions ....................................................................................................iv
About This Manual.................................................................................................viii
Recording Important Information.............................................................................ix
Manual Conventions.................................................................................................. x
Table of Contents .....................................................................................................xi
Overview of Computer ........................................................................................... xiv
Quick Setup
Installing Battery Pack............................................................................................1-1
Connecting to AC Power Source............................................................................1-4
Setting Up Windows...............................................................................................1-6
Turning Off Your Computer ..................................................................................1-8
Basic Operations
Choosing Power Source .........................................................................................2-1
Resetting System ....................................................................................................2-3
Using Glide Pad......................................................................................................2-4
Using Keyboard......................................................................................................2-6
Controlling Volume................................................................................................2-7
Adjusting Display...................................................................................................2-8
Sharing Your Computer .......................................................................................2-11
Battery and Power Management
Battery Pack............................................................................................................3-1
Power Management ................................................................................................3-7
xi
Peripherals
Using Peripherals ...................................................................................................4-1
Optional External Floppy Disk Drive Unit ............................................................4-3
Optional External CD-ROM Drive Unit ................................................................4-6
Display .................................................................................................................4-11
Audio System....................................................................................................... 4-14
USB Device.......................................................................................................... 4-16
PC Card ................................................................................................................ 4-17
Printer...................................................................................................................4-21
Communication Functions
LAN Unit ...............................................................................................................5-1
Wireless LAN.........................................................................................................5-4
Network Setup Utility ............................................................................................5-8
Modem Card (may not be available in some countries) ...................................... 5-10
Setup Utility
Running Setup Utility ............................................................................................6-1
Main Menu ............................................................................................................. 6-3
Advanced Menu .....................................................................................................6-4
Security Menu ........................................................................................................6-4
Boot Menu.............................................................................................................. 6-6
Exit Menu............................................................................................................... 6-6
Connection Cradle
Setting Up Connection Cradle................................................................................7-3
Overview of Connection Cradle ............................................................................ 7-4
Using MM Series as External Hard Disk ...............................................................7-6
Connecting to Host Computer................................................................................ 7-7
Stopping Connection from Host Computer.......................................................... 7-11
Removing from Connection Cradle .....................................................................7-12
Setting Password ..................................................................................................7-13
xii
Appendixes
Maintenance and Care ...........................................................................................A-1
Troubleshooting
Index
xiii

Overview of Computer

Each number after an arrow indicates the page referring to the part. Actual appearance of your computer may be slightly different depending on the model.
Front
Wireless LAN Antenna 5-4
Power Button 1-5
LCD Screen 2-8
xiv
Keyboard 2-6
Status Indicators xv
Glide Pad 2-4
Status Indicators
Hard Disk Indicator
Antenna Indicator
Battery Indicator
Power Indicator
Never turn off the computer when the hard disk indicator is on. This may damage the data on the hard disk.
Right
AC Adapter Jack→1-4
LAN Jack →5-2
PC Card Slot→4-17
Left
Headphone/Audio Output Jack →4-14
USB Port 4-3,7,16,21
Connection Cradle Connector 7-5
USB port4-3,7,16, 21
xv
Rear
→2-3
play
Bottom
Dis
Connector →4-12
Battery Pack→3-1
Reset Switch
Speaker
RESET
Ventilation Openings iv
xvi
CHAPTER 1

Quick Setup

Your computer is designed and pre-configured for easy setup and use. This chapter describes the steps to set up your computer and operate it as quickly as possible. Read this chapter first.

Installing Battery Pack

Your computer is powered with either the battery pack or AC power source. See the next chapter for more information on the power sources. Before using your computer for the first time:
1. Place your computer upside down.
2. Slide the battery stopper on the battery pack to the unlocked position(
).
1
Battery Stopper
1-1
3. Insert the battery pack into your computer by matching the notched parts of the battery to the projected parts on your computer.
Projected Part
1
Notched Part
4. Push the battery pack all the way until you hear the clicking sound.
Projected Part
Notched Part
1-2
5. Slide the battery stopper to the locked position ( ).
6. Turn over your computer and go to the next section.
1
1-3

Connecting to AC Power Source

1. Plug the AC adapter cable into the AC adapter jack on the right side of your computer.
2. Plug the AC power cord into the AC adapter.
3. Plug the AC power cord into a wall outlet.
1
AC Adapter Jack
AC Power Cord
AC Adapter
Always use the AC adapter and the AC power cord included with your computer or the optional one (may not be available in some countries). Using other AC adapters and AC power cords may damage your computer.
Always hold the AC power cord by its plug when removing it from the wall outlet. Never pull on the cord.
When using your computer for the first time, be sure to operate it on AC power. If on battery power instead, you may not be able to complete the Windows setup if the battery does not have enough power.
To Wall Outlet
1-4
4. Slide the display cover lock lever to the right until the display cover releases, and raise the cover.
5. Press the power button to turn on your computer.
Display Cover Lock Lever
Power Button
1
Power Indicator
When you turn on your computer, the power indicator ( computer goes through a self test to detect any problems, and Windows setup process starts. See the next page.
) turns green, your
1-5

Setting Up Windows

The steps in the setup process are as follows:
Configuring your location, language and keyboard type
Configuring your time zone
1
Accepting license agreement
Naming your computer
Creating an account
Completing configuration
To setup Windows, follow the instructions on the screen. See also the Windows manual. It takes approximately 10-15 minutes to complete the entire setup process.
Do not turn off your computer until completing Windows setup. If you
turn it off, you cannot set up Windows later.
Be sure to connect your computer to AC power source. An undercharged battery may not be able to complete the Windows XP setup .
Do not connect any peripheral devices to your computer until
Windows setup completes. Otherwise your computer may malfunction.
If the display turns off, some power management may function. In this case, press any key to resume your computer from the power management.
If you cannot operate the keyboard or the touch pad, press the power button for more than four seconds to turn off your computer. Be sure that the power indicator turns off; then, after more than 10 seconds, press the power button to turn it on again.
After completing Windows setup:
Confirm Time Zone is correctly selected and set the date and time by double- clicking the time appearing on the right of the taskbar to open Date and Time Properties dialog box
Press Fn + F1 ( communication.
) keys to activate the integrated antenna for Wireless LAN
1-6
Properties Dialog Box in Windows
In this manual, you will often see the expression “XXX Properties dialog box.” A dialog box is a window containing text boxes, check boxes, buttons, etc., with which you can send commands to Windows or other application programs. To open the properties dialog boxes, click start - Control Panel. The Control Panel has two types of views: Category view and Classic view. The Category view allows you to choose the category that may be related to what you want to do, then, choose the task by clicking it. The Classic view gives you the icons representing their components or features. Double-click one of the icons to open their dialog box or windows. Some of the dialog boxes you will use often are:
Display
Phone and Modem Options
Mouse
Power Options
System
Clicking Switch to XXX View string appearing at the upper left of the Control Panel window allows you to toggle between the two views.
1
1-7

Turning Off Your Computer

When you’ve finished using your computer, turn it off with one of the following ways:
From the start menu
1. Click start – Turn Off Computer.
1
2. In the Turn off computer dialog box, click Turn Off.
With the power button
Before using this step, confirm that Shut down is selected in When I press the power button on my computer in Advanced tab of Power Options Properties dialog
box.
Close the cover to keep the screen and keyboard clean and protected.
If you have not saved a file, a dialog box will appear asking whether you want to save it.
Do not turn off or reset your computer while the hard disk indicator or the indicator on the optional external floppy disk drive unit or the external CD-ROM drive unit is lit. Doing so may damage or even wipe out the data.
Before turning it back on, wait at least ten seconds after turning off your computer. Turning the power off and on in rapid succession can damage your computer’s electrical circuitry.
1-8
CHAPTER 2

Basic Operations

This chapter describes the basic operations of your computer.

Choosing Power Source

You can use your computer with one of the following power sources:
AC power from a wall outlet
Use AC power whenever possible; rely on the battery only when AC power is not available.
Rechargeable battery
Your computer is equipped with a standard battery pack. You can also use an optional high capacity battery. See Chapter 3 for the battery information.
About Power Indicators
The following indicators show the power status of your computer.
Indicator Light Meaning
Power
Battery
The battery indicator is always off when your computer is turned off and not connected to AC power source.
On (green) Operating Blinking (green) In System Standby Off Powered off or in System Hibernate Connected to AC Power Source
Powered by Battery
On (green) Fully charged On (orange) Being charged
Blinking (orange) Off Has power Blinking (red) Almost completely discharged
In abnormal state (Remove the battery pack and install it again.)
(The warning beep sounds.)
2
2-1
Using AC Adapter
When connected to a wall outlet, the AC adapter provides power for operation and charges the battery. The AC input voltage can range from 100 to 240 volts so that you can use your computer with the appropriate plug adapter.
2
When the battery is hot, the battery indicator may turn off and stay off until the battery becomes cool.
For more information on System standby/hibernate, see Chapter 3.
The AC power cord included with your computer is appropriate for the voltage used in the area in which you purchased your computer. If you attempt to connect your computer to a wall outlet other than in this area, check the voltage of the outlet and use an AC power cord appropriate for the outlet. Consult local service staff if you are not sure.
2-2

Resetting System

RESET
You may need to restart the system if your computer hangs up or a new hardware or software is installed. When a message appears after the installation, click OK, Yes, etc. to restart Windows. You can also restart Windows by clicking start - Turn Off Computer; then, Restart.
Warm Boot (Software Reset)
If the system is locked up because of a software problem, you can reset or reboot the system by pressing the Ctrl+Alt+Del keys simultaneously and select Applications tab of Windows Task Manager dialog box. Click the program name which hangs up, then,
End Task. If this does not solve the problem, click Disconnect or Logoff of Windows Task Manager dialog box, then Yes.
Resetting may cause data loss. Use the resetting process only if the normal Windows Shut Down does not work because of software malfunction. Although resetting will not damage the system, you may lose the data you are processing.
Power Switch
You can turn off your computer with the power button if you encounter hardware or software problems which lock up the system. In this case, press the power button for more than four seconds.
Reset Switch
If you cannot turn off your computer by pressing the power button, you can use the reset switch on the bottom of your computer. To reset the system, insert a narrow object into the small hole to press the switch.
Reset Switch
2
RESET
2-3

Using Glide Pad

Your computer is equipped with an integrated pointing device called a glide pad. Using the glide pad, you can move the pointer, select an item from a menu, and perform other tasks in the same way you would with a mouse.
2
Do not hit or scratch the surface of the glide pad with pointed objects (such as a ballpoint pen).
Do not operate the glide pad with a moist finger. This may cause the glide pad to operate incorrectly.
Using Glide Pad
Take a moment to become familiar with how the glide pad works.
Place Your Fingertip
Place your left or right hand next to the glide pad, resting your wrist naturally in a relaxed manner. Place your thumb or finger on the glide pad.
Move Your Fingertip
The rectangular pad of the glide pad is used to move the pointer around the display. As you slide your fingertip across the pad, the pointer on the screen moves in the same direction across the screen. The glide pad is very sensitive, so you do not have to exert much pressure on the pad. The glide pad will respond to a light touch from your fingertip.
Glide Pad
2-4
+ 93 hidden pages