Sharp PC-GP2 User Manual

 

 

 

Notice for Users in the UK and Ireland

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked indicated on the pin face of the plug must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut-off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral Brown: Live

As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

•

The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.

or and of the same rating as above; which is also

•

The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.

Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three pin plug.

Before replacing the plug cover, make sure that:

•

If the new fitted plug contains a fuse, Its value is the same as that removed from the cut-off plug.

•

The cord grip is clamped over the sheath of the mains lead and not simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

Recording and playback of any material may require consent, which SHARP is unable to give. Please refer particularly to the provisions of the Copyright Act 1956, the Dramatic and Musical Performers Protection Act 1958, the Performers Protection Acts 1963 and 1972 and to any subsequent statutory enactments and orders.

Notice for Users in Europe

About the Modem

Your Sharp PC-GP series with integral modem has been designed to work with the analogue PSTN’s in the following countries:

United Kingdom

•

Ireland

•

Italy

•

Germany

•

Switzerland

•

If you wish to connect the equipment to the PSTN in a country not listed above, you should contact your equipment supplier for further details.

The modem is not designed for use on a shared service line or a line equipped with a call waiting facility. If you attempt to use the modem on a telephone line with call waiting, you may experience communication errors.

To maintain CTR21 network compatibility when used in the countries listed above the following setting should be observed:

Pulse dial may not be available in some countries.

Modem Model Name: V1456VQL-P1(INT)

Intended Use

This is a Personal Computer with Modem for the analogue PSTN network which operates in all UK, Irish, Italian, German, Swiss networks which follow the CTR21 Standard. If you are in doubt whether your network follows the CTR21, please contact your dealer or network operator.

iii

This equipment complies with the requirements of the Directive 1999/5/EC.

Dieses Gerät entspricht den Anforderungen der EU-Richtlinie 1999/5/EG.

Cet appareil est conforme aux exigences de la directive 1999/5/CE.

Este aparato satisface las exigencias de las Directiva 1999/5/CE.

Quest'apparecchio è conforme ai requisiti delle direttiva 1999/5/CE.

Dit apparaat voldoet aan de eisen van de richtlijn 1999/5/EG.

Este equipamento obedece às exigências da directiva 1999/5/CE.

Η συσκευη αυτη ανταττοκρινεται στιζ ατταιτησειζ των οδηγια

Denna utrustning uppfyller kraven enligt direktiv 1999/5/EC.

Dette udstyr overholder kravene i direktiv 1999/5/EF.

Dette produktet oppfyller kravene i direktiv 1999/5/EC.

Tämä laite täyttää direktiivi 1999/5/EY.

1999/5/EK .

CAUTION:

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING.

CAUTION:

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY.

VORSICHT:

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN.

ATTENTION:

POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE.

VARNING:

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH TA UR BATTERIET.

PRECAUCION:

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED Y LA BATERIA.

Safety Precautions

General

Follow all cautions and instructions, which may be marked, on the computer.

•

Except as described elsewhere in this manual, refer all servicing to qualified

•

personnel. Immediately shut off the computer and seek servicing under the following conditions:

when the power cord or plug is damaged or frayed

•

if liquid has been spilled on the computer

•

if the computer has been dropped or the cabinet has been damaged

•

Location

•

Do not expose the computer to direct sunlight. Try to avoid dusty environments. Keep the computer away from any magnetic devices and TVs. Keep the computer away from excessive humidity or fluids such as rain, snow,

water spray, juice, coffee, steam, etc. Do not move the computer from an extremely cold place to an extremely warm

place. A temperature difference of more than 10°C (18°F) will cause condensation inside the unit, which may cause damage.

Do not block or cover slots or openings on the cabinet. These protect the computer

•

from overheating. Care should be exercised when using on heat sensitive surfaces or your lap as the

•

base of this computer will get hot.

Usage

Never push any objects of any kind into cabinet openings. They may touch

•

dangerous voltage points or short parts that could result in fire or electrical shock. Turn off the computer before installing or removing any peripheral devices except

•

when connecting USB devices, IEEE 1394 devices, and PC cards. (Also, you do not have to turn off the computer before inserting/ejecting SD cards and smart media cards).

Check the AC power cord and power connectors periodically for damage. Replace

•

the power cord immediately if damage is found.

Never subject your computer to sudden shocks or extreme vibration.

•

Do not drop the computer nor hit it with other equipment.

•

Do not scratch the surface of the LCD screen.

•

Turn off the computer and disconnect the AC power cord before cleaning.

•

Battery Pack Precautions

CAUTION

DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.

Handling

Never put the battery pack in a fire, as it could explode and cause injury.

•

Do not attempt to open or alter the battery pack.

•

Do not place the battery where it might get hotter than 60°C (140°F).

•

Do not allow metal objects such as jewelry to short across the battery terminals, as

•

it could heat up and explode. Do not allow liquids to come in contact with the battery pack.

•

Avoid dropping the pack or other violent shock.

•

Do not solder anything to the battery terminals.

•

Charging

Charge the battery pack only with the AC adapter included with your computer.

•

vii

Discharging

Do not use the battery pack for any purpose other than powering the computer.

•

Storage

Store the battery pack in a cool and dry place. Never allow the temperature to

•

exceed 60°C (140°F) during storage. Recharge the battery pack after storage, before use.

•

Modem Precautions

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

Do not use this product near water, for example, near a bath tub, wash bowl,

•

kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm.

•

There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak.

•

Never install telephone wiring during a lightning storm.

•

Never install telephone jacks in wet locations unless the jack is specifically

•

designed for wet locations. Never touch uninsulated telephone wires or terminals unless the telephone line has

•

been disconnected at the network interface. Use caution when installing or modifying telephone lines.

•

viii

About This Manual

Notice

Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation.

SHARP Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.

SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other causes.

SHARP assumes no responsibility directly or indirectly, for financial losses or claims from third persons resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss of or alteration of stored data, etc.

Edition

1st Edition, July 2002.

© 2002 SHARP Corporation This document contains or refers to proprietary information which is protected by copyright. All rights are reserved. Copying or other reproduction of this document is prohibited without the prior written permission of SHARP Corporation.

Trademarks

Intel and Pentium are registered trade mark of Intel Corporation. IBM is a trademark of International Business Machines Corporation. SD logo is a trademark. SmartMedia is a registered trademark of Toshiba Corporation. Microsoft, MS-DOS, Windows, and the Windows Logo are registered trademarks of Microsoft Corporation.

WinDVDTM is a trademark of InterVideo,Inc.

All other brand and product names are trademarks or registered trademarks of their respective holders.

Recording Important Information

For future reference, please record the following information in the spaces provided below.

Model Number:

Serial Number:

Date of purchase:

Dealer’s Name:

Place of purchase:

Password:

The serial number is printed on a sticker located on the bottom of the computer.

Manual Conventions

This manual uses a set of style conventions described below.

Notes and Cautions

A note icon informs you of a special technique or information that may help you perform a task or better understand a process.

A caution icon alerts you to something that may cause problems or damage to hardware, software or data.

Key Labels on the Keyboard

boldface: Press

When two or more keys are pressed simultaneously, the key labels are separated by a plus (+) sign: Restart your computer by pressing

Enter

are italicized with icons:

, when referred to in the instructions, are shown in

to continue.

Ctrl+Alt+Delete

Sample Entries

c:/windows/system

Words/Texts on Screen

Double-click this icon to display the Power Properties window. Set the item to Enabled.

Screens

your computer.

Section Titles

Refer to Installing Battery Pack section of Chapter 1.

reproduced in this manual may differ slightly from the screens you see on

are shown in lower cases of different typeface.

, such as window titles or possible parameters, are italicized:

in other parts of this manual are italicized:

Notice for Users in the UK and Ireland ......................................................................i

Notice for Users in Europe....................................................................................... iii

Safety Precautions.....................................................................................................vi

About This Manual...................................................................................................ix

Recording Important Information ..............................................................................x

Manual Conventions .................................................................................................xi

Table of Contents.....................................................................................................xii

Overview of Computer ...........................................................................................xiv

Quick Setup

Installing Battery Pack........................................................................................... 1-1

Connecting AC Power ........................................................................................... 1-3

Setting Up Windows XP........................................................................................ 1-5

Turning Off Your Computer .................................................................................. 1-6

Basic Operations

Choosing Power Source......................................................................................... 2-1

Resetting the System.............................................................................................. 2-3

Using the Glide Pad............................................................................................... 2-4

Using the Keyboard ............................................................................................... 2-6

Using the Floppy Disk Drive ................................................................................. 2-8

Using the SD Card Slot........................................................................................ 2-10

Using the Smart Media Card Slot ........................................................................ 2-12

Using the Optical Drive ....................................................................................... 2-15

Writing Data to CD-R/RW .................................................................................. 2-17

Watching DVD-ROM Video ............................................................................... 2-18

Controlling Audio ................................................................................................ 2-21

Adjusting the Display .......................................................................................... 2-22

Sharing the Computer .......................................................................................... 2-24

Battery and Power Management

Battery Pack........................................................................................................... 3-1

Power Management ............................................................................................... 3-7

xii

Peripherals

Using Peripherals................................................................................................... 4-1

Display................................................................................................................... 4-3

Audio System......................................................................................................... 4-5

USB Device ........................................................................................................... 4-8

PC Card.................................................................................................................. 4-9

Printer .................................................................................................................. 4-11

Using IEEE 1394 Devices ................................................................................... 4-12

Communication Functions

Built-in Modem...................................................................................................... 5-1

LAN unit................................................................................................................ 5-4

Setup Utility

Running the Setup Utility ...................................................................................... 6-1

Main Menu............................................................................................................. 6-3

Advanced Menu..................................................................................................... 6-4

Security Menu........................................................................................................ 6-5

Exit Menu .............................................................................................................. 6-7

Appendixes

Memory Module ....................................................................................................A-1

Maintenance and Care............................................................................................A-4

Troubleshooting

Index

xiii

Overview of Computer

Each number after an arrow indicates the page referring to the part. Actual appearance of your computer may be slightly different depending on the model.

Front

Power/ Battery Status Indicators

→

2-2

Speaker

Microphone

LCD Screen

→

2-22

Antenna Indicator

(See the supplement for Wireless LAN model)

Power Button

xiv

Glide Pad

→

2-4

Optical Drive

Hard Disk Drive

Floppy Disk Drive

Status Indicators

Caps Lock

Num Lock

Scroll Lock

Keyboard

→

2-6

Right

Smart Media Card Slot

→

2-12

Left

SD Card Slot

→

2-10

Ventilation Openings → vi

PC Card Slot

→

4-9

Optical Drive

→

2-15

Floppy Disk Drive

→

2-8

Rear

Microphone Jack

→

4-7

IEEE1394 Connector

→

4-12

LAN Jack

→

5-4

S Video Output Jack

→

2-20

AC Adapter Jack

→

1-3

Audio Output Jack (S/PDIF compliant)

→

Bottom

4-5

Modem Jack

→

5-2

USB Ports

→

4-8

Memory Slot Cover→A-2

Battery Pack →3-1

Parallel Port

→

4-11

Security Slot

→

A-8

External Monitor Port

→

4-3

Reset Switch →2-3

xvi

CHAPTER 1

Quick Setup

Your computer is designed and pre-configured for easy setup and use. This chapter describes the steps to set your computer up and running as quickly as possible. Read this chapter first.

Installing Battery Pack

Your computer is powered with either the rechargeable battery pack or AC power. See the next chapter for more information on power sources. Before using the computer for the first time:

1. Place the computer upside down.

2. Slide the battery lock lever to the unlocked position(

Battery Lock Lever

1-1

3. Insert the battery pack into the computer.

4. Push the battery pack until you hear the clicking sound.

5. Slide the battery lock lever to the locked position ( ).

6. Turn over the computer and go to the next section.

1-2

Connecting AC Power

1. Plug the AC adapter cable into the AC adapter jack on the rear side of your computer.

2. Plug the AC power cord into the AC adapter.

3. Plug the AC power cord into a wall outlet.

AC Adapter

AC Adapter Jack

AC Power Cord

•

Always use the AC adapter included with the computer. Using other AC adapters may damage the computer.

•

Always hold the AC power cord by its plug when removing it from the wall outlet. Never pull on the cord.

•

When using the computer for the first time, be sure to connect it to AC power. When using the battery instead, you may not be able to complete the Windows XP setup if the battery does not have enough power.

4. Slide the display cover lock lever to the right until the display cover releases, and raise the cover.

Display Cover Lock Lever

To Wall Outlet

1-3

5. Press the power button to turn on your computer.

Power Indicator

Power Button

When you turn on the computer, the power indicator ( computer goes through a self test to detect any problems, and

starts. See the next page.

Wizard

) turns green, the

Windows XP Setup

1-4

Setting Up Windows XP

The steps in the setup process are as follows:

Configuring your location, language and keyboard

•

Configuring your time zone (for U.S. Users)

•

Accepting license agreement

•

Naming your computer

•

Creating an account

•

Completing configuration

•

To set up Windows XP, follow the instructions on the screen. See also the Windows XP quick start guide. It takes approximately 5-10 minutes to complete the entire setup process.

Do not turn off the computer while completing the Windows XP setup.

•

Be sure to connect the computer to AC power. If the battery is used and

•

it does not have enough power, you may not be able to complete the Windows XP setup.

Do not connect any peripheral devices to your computer until the

•

Windows XP setup completes. Otherwise your computer may malfunction.

If the display turns off, some power management may function. In this

•

case, press any key to resume your computer from the power management. If you cannot operate the keyboard or the glide pad, press the power

•

button for more than four seconds to turn off the computer. Be sure that the power indicator turns off; then, after more than 10 seconds, press the power button to turn it on again.

After completing the Windows XP setup, set your date and time. Double-click the time appearing on the right of the taskbar to open box. Confirm

Properties Dialog Box in Windows

In this manual, you will often see the expression “XXX Properties dialog box.” The dialog box is a window containing text boxes, check boxes, buttons, etc., with which you can send commands to Windows or other applications. To open the properties

Time Zone

Date and Time Properties

is correctly selected, and set date and time.

dialog

1-5

dialog boxes, click

. One is

Panel

, you can choose the category which may be related to what you want to do, then,

View

choose your task by clicking it. If simultaneously. You can open a property dialog box, or a similar window, for the component or feature represented by that icon, by double-clicking it. Some of the dialog boxes you will use often are:

Display

•

Phone and Modem Options

•

Mouse

•

Power Options

•

System

•

Category View

start

Control Panel.

, and the other is

Classic View

Turning Off Your Computer

When you’ve finished using your computer, turn it off using one of the following steps:

•

From the

1. Click

2. In the

•

With the power button Before using this step, confirm that

power button on my computer

dialog box (found in the

start

Turn Off Computer

Turn off computer

Control Panel

dialog box, select

Advanced

There are two types of views for the

Classic View

Shut down

tab of

is selected, all the icons appear

Turn Off

is selected in

. If you select

When I press the

Power Options Properties

Control

Basic Operations

This chapter describes the basic operations of your computer.

Choosing Power Source

You can use the computer with one of the following power sources:

AC power from a wall outlet

•

Use AC power whenever possible; rely on the battery only when AC power is not available.

Rechargeable battery

•

Your computer is equipped with a battery pack. See Chapter 3 for battery information.

2-1

About the Power Indicators

The following indicators show the power status of your computer.

Indicator Light Meaning

Power

Battery Status

Battery status indicator is always off when the computer is turned off and not connected to AC power.

On (green) Operating (powered by AC power) Blinking (green) In System Standby (when powered by AC

Off Powered off / in System Hibernate/

When Connected to AC Power

When Powered by Battery

•

When the battery is hot, the battery status indicator may turn off and stay off until the battery becomes cool. (See section of Chapter 3 for more information.)

•

For more information on System standby/hibernate, see Chapter 3.

Using the AC Adapter

When connected to a wall outlet, the AC adapter provides power for operation and charges the battery. The AC input voltage can range from 100 to 240 volts so that you can use the computer with the appropriate plug adapter.

The AC power cord included with the computer is appropriate for the voltage used in the area in which you purchased your computer. If you attempt to connect the computer to a wall outlet other than in this area, check the voltage of the outlet and use an AC power cord appropriate for the outlet. Consult local service staff if you are not sure.

power)

powered by a battery pack On (green) Fully charged On (orange) Being charged Blinking (orange) Off Has power Blinking (red)

In abnormal state. Remove the battery

pack and install it again. (See Chapter 3)

Almost completely discharged

(The warning beep sounds)

Charging the Battery Pack

2-2

Resetting the System

You may need to restart the system if the computer becomes inoperable or after adding a new hardware or software.

Warm Boot (Software Reset)

If the system is locked up because of a software problem, you can reset or reboot the system by pressing the instructions on the screen.

Resetting may cause data loss. Use the resetting process only if the normal Windows XP Shut Down does not work because of software malfunction. Although resetting will not damage the system, you may lose the data you are processing.

Ctrl + Alt + Del

Power Switch

You can turn off the computer with the power button if you encounter hardware or software problems, which lock up the system. In this case, press the power button for more than four seconds.

Reset Switch

If you cannot turn off the computer by pressing the power button, you can use the reset switch on the bottom of your computer. To reset the system, insert a narrow object into the small hole to press the switch.

keys simultaneously and follow the

Reset Switch

2-3

Using the Glide Pad

Your computer is equipped with an integrated pointing device called glide pad. By moving the pointer with the glide pad, you can select an item from a menu, and perform other tasks in the same way you would with a mouse.

•

Do not hit or scratch the surface of the glide pad with pointed objects (such as a ballpoint pen).

•

Do not operate the glide pad with a moist finger. This may cause the glide pad to operate incorrectly.

Using the Glide Pad

Glide Pad

Take a moment to become familiar with how the glide pad works.

Place Your Fingertip

Place your left or right hand next to the glide pad, resting your wrist naturally in a relaxed manner. Place your thumb or finger on the glide pad.

Move Your Fingertip

The rectangular pad of the glide pad acts like a miniature duplicate of the display. As you slide your fingertip across the pad, the pointer on the screen moves in the same direction across the screen. The glide pad is very sensitive, so you do not have to exert much pressure on the pad. The glide pad responds to a light touch from your fingertip.

2-4

Click, Double-click, and Right-click

To click or double-click, you can use the left button just like that of a mouse. Instead of clicking the left button, you can also just tap gently anywhere on the rectangular pad. For right-clicking, you must use the right button.

Drag and Drop

You can move icons or windows by using “drag and drop” below:

1. Position the pointer over the object.

2. Press the left button; do not release it.

3. Holding down the button, move the pointer. The object moves together with the pointer.

4. Release the button when the object reaches its destination.

Or you can tap the pad twice instead of pressing the left button in step 2.

Scroll

You can scroll through information in a list or in a document by using the glide pad. To view information vertically, place your finger on the most right part of the glide pad and slide your finger up and down. To view horizontally, place your finger on the bottom part of the glide pad and slide your finger to the left or the right. This procedure works only in limited applications.

Changing the Configuration

In the

Mouse Properties

pad, such as swapping left and right buttons, changing the pointer size, etc. Doubleclick

icon on the taskbar to open the

dialog box, you can change the configuration of the glide

Mouse Properties

dialog box.

2-5

Using the Keyboard

Your computer, equipped with the Windows Enhanced Keyboard, provides all the functionality of a full-sized desktop keyboard.

Special Keys

Windows Key

Application Key

System Function Keys

When pressed together with the Fn key, function keys set specific system parameters. This combination is sometimes referred to as “hot keys”.

Fn + F1

Fn + F3

Fn + F4

Fn + F5

Fn + F6

Fn + F7

Fn + F8

Fn + F10

Fn + F11

Turns the wireless LAN connection on and off (This combination functions for built-in wireless LAN model only and when to

Enabled.

Decreases the audio volume

Increases the audio volume

Rotates display mode between LCD only, CRT only, and simultaneously display (when connecting a CRT monitor)

Decreases the LCD screen brightness

Increases the LCD screen brightness

Maximizes the LCD screen brightness Returns to the previous status by pressing them again

Stops the battery warning beep (This key combination does not work for Windows battery warning beep)

Turns the LCD screen on and off

Opens the Windows start menu.

Opens an application-specific short-cut menu equivalent to right-clicking.

Wireless LAN

)

Security

menu in the Setup Utility is set

2-6

Fn + F12

Forces the computer into System standby/System hibernate/ Shut down (See

Power Management

of Chapter 3 for more information.)

2-7

Using the Floppy Disk Drive

You can use a double-density (2DD) 720KB or high-density (2HD) 1.44MB floppy disk.

Handling Floppy Disks

Do not open the shutter and touch the disk inside; otherwise, you will not be able to

•

read or write data from/to the disk.

Do not place floppy disks near magnets or heat source, in direct sunlight or in a

•

dusty place, etc.

Never subject floppy disks to sudden shocks or extreme vibration. Do not drop or

•

bend them, or place heavy objects on them.

Do not spill liquid onto floppy disks.

•

Inserting and Removing a Floppy Disk

Inserting

Hold the floppy disk with the arrow facing up and towards the drive. Slide the disk into the drive until it locks into place. When the disk is correctly inserted, the eject button pops out.

Label Facing Up

2-8

Always insert a floppy disk straight into the floppy disk drive.

•

When inserting a disk, make sure it is not upside down.

•

Do not use excessive force when inserting a floppy disk. If you have

•

difficulty inserting or removing it, seek the assistance of an authorized service technician. Do not touch the disk while reading/writing data. It may cause

•

malfunction of the computer and the drive.

Removing

Before removing the floppy disk, make sure the floppy disk drive indicator is not lit.

Press the eject button firmly. The disk pops out slightly. Remove it and store it properly.

Eject Button

Floppy Disk Drive Indicator

Formatting a Floppy Disk

1. Make sure the floppy disk is not write-protected, and insert it into the floppy disk drive.

2. Click

3. Right-click

4. Select the appropriate formatting options.

5. Click

start - My Computer

3 ½ Floppy (A:)

to start formatting.

Start

icon; then, click

Format….

from the pop-up menu.

•

When you format a floppy disk, all data previously stored on the disk is lost.

•

You cannot format a double-density (2DD) 720KB floppy disk.

2-9

Using the SD Card Slot

Your computer is equipped with a SD card slot. You can insert/eject a SD memory card without turning off the computer. Before inserting a SD memory card into the slot, refer to its manual.

•

You cannot read/write any copy-protected data from/into a SD memory card with built-in the copyright protection technology

Inserting a SD Memory Card

Insert a SD memory card into the slot with the SD logo face up and the notched part backward until it locks into place. When the card inserted correctly, the on the taskbar turns to red; then, green when it is ready for reading or writing.

compliant with the SDMI specification.

•

Make sure to log on the computer as a member of the Computer administrators group. Otherwise, you do not have the the taskbar and cannot remove the card safely and correctly.

Make sure to unlock the write protect switch on the SD memory card when you write data into the card. Refer to the manual of the SD memory card for more information about the write protect switch.

indicator on

indicator

2-10

Notched Part

SD Logo Facing Up

SD Card Slot

Make sure to insert the card with the SD logo face up and the notched part backward. Otherwise, the card and the computer may be damaged.

If the dialog box asking you task you want.

The color of the

: no card in the slot or able to eject the card

Gray

Ejecting a SD Memory Card

: able to access the card

Green

: reading or writing the data from/into the card

Red

•

1. Click

2. Right-click turns to gray from green.

Make sure to right-click

3. Push the SD memory card into the computer until you hear the clicking sound. The card pops out slightly.

indicator means:

Do not remove the card nor turn off the computer when the on the taskbar is green or red. Otherwise, the SD memory card or the data may be damaged. Be sure to follow the instructions below when ejecting a SD memory card. Otherwise, the system may not work properly.

start – My computer

Removable Disk(E:)

What do you want Windows to do?

; then,

Removable Disk (E:)

Eject

. The

appears, select the

indicator

indicator on the taskbar

Removable Disk (F:)

, not

2-11

4. Gently pull out the card.

Using the Smart Media Card Slot

Your computer is equipped with a smart media card slot accommodating a 3.3V smart media card. You can insert/eject the card without turning off the computer. Before inserting the card into the slot, refer to its manual.

•

Only a 3.3V smart media card is supported by your computer. You cannot use a 5V card with your computer.

•

Make sure to log on the computer as a member of the Computer administrators group. Otherwise, you do not have the the taskbar and cannot remove the card safely and correctly.

Inserting a Smart Media Card

Insert a smart media card into the slot with the notched part set frontward. When the card is inserted correctly, the when it is ready for reading or writing.

indicator on the taskbar turns to red; then, green

indicator on

2-12

Smart Media Card Slot

Notched Part

Make sure to insert the card with the notched part forward. Otherwise, the card and the computer may be damaged.

If the dialog box asking you task you want.

The color of the

: no card in the slot

Gray

Ejecting a Smart Media Card

: able to access the card or able to eject the card

Green

: reading or writing the data from/into the card

Red

•

indicator means:

Do not remove the card nor turn off the computer when the on the taskbar is red. Otherwise, the smart media card or the data stored on it may be damaged. Be sure to follow the instructions below when ejecting a smart media card. Otherwise, the system may not work properly.

What do you want Windows to do?

appears, select the

indicator

1. Click

2. Right-click

3. Push the smart media card into the computer. The card slightly pops out. The

start – My computer

Removable Disk(F:)

Make sure to right-click

indicator on the taskbar turns to gray from green.

; then,

Eject

Removable Disk (F:)

Removable Disk (E:).

, not

2-13

4. Gently pull out the card.

2-14

Using the Optical Drive

With the optical drive, you can read data from CD and write data into CD-R/RW. Furthermore, you can enjoy a movie etc, with the DVD-ROM disk.

CAUTION FOR LASER

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Maximum output and wavelength of the laser: 85mW, 795nm(CD-R/RW) 6mW,668nm(DVD-ROM)

CLASS1LASER PRODUCT

LASERKLASSE1

Handling Disks

Do not write on either side of the disk, particularly the non-label side. Data is read

•

from the non-label side. Do not mark this surface.

Keep your disks away from direct sunlight, heat and excessive moisture.

•

Always hold the disks by the edges. Fingerprints, dirt or water on the disks can

•

cause noise or mistracking. If a disk is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the center, along the radius.

Inserting a Disk

1. Make sure the optical drive indicator is not lit on; then, press the eject button. The drive tray opens slightly.

Optical drive Indicator

Eject Button

2-15

2. Gently pull out the tray.

3. Place your disk, label side up, onto the tray and slightly press the center of the disk until it locks into place.

4. Gently push the tray back into the computer.

2-16

•

Do not leave the tray pulled out. Also, avoid touching the lens in the tray. If the lens becomes dirty, the disk may malfunction.

•

Do not wipe the lens with materials with rough surface (such as paper towels). Instead, use a cotton swab to gently wipe the lens.

Removing a Disk

1. Make sure the optical drive indicator is not lit and press the eject button. The optical drive tray opens slightly.

2. Gently pull out the tray.

3. Remove the disk from the tray by holding its edge.

4. Gently push the tray back into the computer.

Make sure the optical drive indicator is not lit or blinking before pressing the eject button.

Writing Data to CD-R/RW

You can use a CD-R or a CD-RW disk to write data on. CD-RW is an erasable disk onto which you can write data and from which you can erase data. CD-R is nonerasable disk onto which you can write data only once. If free space remains, you can add data until the disk is full.

To write data, run the application called computer. See the online help of

Before writing to CD-R/RW, follow the instructions below:

•

Connect the AC adapter. If the battery is discharged, writing to the disk will be stopped and the write process will fail.

•

Disable the power management. See Chapter 3.

•

Close any applications which are unnecessary for writing, or will start automatically when the computer is turned on.

•

Disable the screen saver.

Drag’n Drop CD

installed with your

for the details.

Power Management

2-17

Watching DVD-ROM Video

You can enjoy watching DVD-ROM video on your computer using the application called

Win DVD

Changing Region Code

A DVD-ROM disk has a region code which prevents playback of the disk in certain regions. The region code appears on the top of the disk. When shipped from the factory, your DVD-ROM drive is set to a region code applicable to your area. (may not be available in some areas)

. See online help of

•

Before watching DVD-ROM video, follow the instructions below:

•

Connect the AC adapter. If the battery is discharged, the operation will stop.

•

Disable the power management. See Chapter 3.

•

Close any applications that are unnecessary.

•

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. (Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216;,

4,819,098 and 4,907,093 licensed for limited viewing uses only.) Make sure to remove the DVD-ROM disk from the drive when you finish watching it. If you turn off the computer with the disk left in the drive, the drive may not be recognized when the computer is turned on again.

Win DVD

for more details.

Power Management

Available region codes are:

Region Code Area

1 U.S.A, Canada, U.S. Territo ries 2 Europe, South Africa, Middle East, Japan 3 Southeast Asia, East Asia(including Hong Kong)

4 Australia, New Zealand, Pacific Islands, Central

America, Mexico, South America

5 Former Soviet Union, Indian Subcont inent, Africa 6 China

2-18

To change the region code:

1. Insert a DVD-ROM disk into the drive. If the region code of your disk is different from that of your DVD-ROM drive, the message “

2. Click OK.

3. The region code currently selected is checked in the left box. Region code of your disk is checked in the right box. If you want to change the code and play your disk, click

On some DVD-ROM disks, plural region codes are selectable in the right box of code.

Playback of content from this region is not permitted

Confirm Region

OK.

Confirm Region

dialog box appears.

dialog box. Carefully choose an appropriate

” appears.

Use Parental Control

If you want to set the parental control to prevent your children from watching an inappropriate movie, click and select want. See online help of

Parental Control

icon of

tab. Select the control level and set your password if you

WinDVD

for more details.

to open the

Properties…

dialog box,

Disabling LCD Optimization

Your computer optimizes the screen visibility automatically when you play a DVD video. When the screen is not appropriate for you, disable the LCD optimization function. Click

Display

tab; then, uncheck

icon of

WinDVD

LCD Optimization

to open the

Properties…

dialog box, and select

Displaying Video on Your TV Set

You can connect a television set with S-Video input to your computer and enjoy DVD video on a big display.

•

Before connecting the television set, disconnect the external monitor.

•

Connect the computer and the television set directly. Otherwise, the screen may be distorted.

1. Turn off the computer and the television set.

2-19

2. Connect the television set to your computer.

Audio Output Jack

Stereo Mini Plug

3. Turn on the computer and the television set.

4. Right-click somewhere on the Windows desktop and click pop-up menu.

5. Click

6. Set

7. If you can see the screen image on the television set, click

8. Click OK and close

Settings t

Mode Settings

Primary

Display Properties

ab -

icon.

Driver mode

S Video Output Jack

To S Video Input Jack

To Audio Input Jacks:

White Plug to Left

Red Plug to Right

dialog box opens.

Advanced

Display Properties

button -

Utility Manager

and click OK twice.

dialog box.

tab; then, select

Properties

Yes

from the

Driver

•

Before disconnecting the television set, be sure to turn off the computer and the television set.

•

After disconnecting the television set, set back the display property following the steps 4 to 6 and set the appropriate resolution.

Enjoying Dolby Digital Audio

Your computer is Dolby Digital compliant. If you connect Dolby Digital compliant audio equipment or headphones, you will have an audio output similar to a big theater. For connection, refer to

WinDVD

enjoy Dolby sound just by connecting normal headphones. To set this function, click

Headphone

DVD-ROM disk. Refer to the online help of

2-20

Audio System

is equipped with

icon and select

properties page is available only while you are playing a

of Chapter 4.

Dolby Headphone

properties.. You can

tab. The

WinDVD

for more details.

Dolby

Controlling Audio

You can control the output volume of your computer with the following steps.

With the keyboard

Press Fn and F3 keys simultaneously to decrease the output volume. Press Fn and F4 keys simultaneously to increase the output volume.

This operation also adjusts the Windows volume control below. For example, if you press Fn + F3 keys, the volume level in Windows will decrease, too.

In Windows

1. Click

2. Click

3. In

4. Click OK and close the dialog box; then the

If you want to control the output volume of each source individually:

1. Click

2. Click

3. In

4. Slide the lever of the source that you want to control.

5. Close the dialog box, then; click

If you control:

Wave

SW Synth

CD Player

start - Control Panel

Sounds, Speech, and Audio Devices

Classic view is selected, double-click

Sounds and Audio Devices Properties

output volume.

Check the box of above. Next time you find the speaker icon on the taskbar, and it is easy to control the volume.

start - Control Panel

Sounds, Speech, and Audio Devices

Classic view is selected, double-click

Sounds and Audio Devices Properties

Device volume

section.

Controlling the volume of CD/DVD or WAVE file



Controlling the volume of MIDI file



Controlling the volume of CD/DVD if the application selects



analog playback.

; then,

Sounds and Audio Devices

dialog box, slide the lever to control the

Control Panel

Place volume icon in the taskbar

; then,

Sounds and Audio Devices

dialog box, click

and close the

Control Panel

icon.

window.

on the step 3 of the

icon.

Advanced

… button of

window.

. If

2-21

Adjusting the Display

You can adjust the brightness, resolution, and number of colors of the internal LCD display.

Changing Brightness of Display

Press Fn and F6 keys simultaneously to decrease the brightness of the display. Press Fn and F7 keys simultaneously to increase the brightness of the display. Press Fn and F8 keys simultaneously to maximize the brightness of the display.

To return the previous brightness, press them again.

Changing Resolution and Number of Colors

When shipped, your computer is set to the default resolution and color. The default resolution is 1024 x 768 at 64k colors. To change the resolution and the number of colors, follow the instructions below:

1. Right-click anywhere on the Windows desktop, except icons or folders.

2. Select

3. In the

Properties

Display Properties

4. Select the number of the colors in

Screen resolution

5. Click OK. If the

Resolutions and Colors you can choose

Resolution

800 x 600 64K

1024 x 768 64K

1280 x 1024

1600 x 1200

1920 x 1440

2048 x 1536

(*1)

On the internal LCD screen, the number of colors in this mode is made using a Dithering algorithm.

from the pop-up menu.

dialog box, select

Color quality

. Refer to the table below for possible resolution and colors.

Monitor Setting

Number of Colors

16M

(*2)

64K

16M

(*2)

64K

16M

(*2)

64K

16M

(*2)

64K

16M

dialog box appears, click

(*1)

Settings

tab.

, and select the resolution in

Yes

2-22

(*2)

Can be chosen for an external monitor only when it is capable of the listed

resolution modes. Cannot be set when displaying only on the LCD monitor and on both of LCD and an external monitor simultaneously.

•

You cannot switch to a display resolution and number of colors that are not available.

•

In the

Highest(32 bit)

•

If you select

Color quality, Medium (16 bit)

means about 16,770,000 (16M) colors.

Highest

, drawing speed may be delayed.

means 65,536 (64K) colors, and

Changing Wallpaper and Setting Screen Saver

You can enjoy various desktop patterns or screen savers.

Changing Wallpaper

1. Follow the steps 1 and 2 on the previous page.

2. In the

3. Select an appropriate wallpaper in

4. Click OK.

Setting Screen Saver

1. Follow the steps 1 and 2 on the previous page.

2. In the

3. Select an appropriate screen saver in

4. Click OK.

Display Properties

saver starts.

dialog box, select

Background

dialog box, select

Screen saver

Desktop.

Screen Saver

and set time when screen

2-23

Sharing the Computer

If you are sharing the computer with your colleagues or family members, set a user account for each person. Every user can choose his/her favorite desktop setting, web site lists, or make his/her own account. When you turn on the computer, select your user account.

Set a New User Account

1. Click

2. Click icon.

3. Click

4. Type a name for the new account and click

5. Select the account type; then, click

Limited Help and Support Center

6. Close the

If more than one user accounts are set to the computer, you must select which user account you will log in when you turn on the computer.

Log off the Computer

“Log off” is useful because you do not have to turn off the computer when you finish your task and pass the computer to another person. There are two ways to log off the computer;

If you select closing your current applications. For example, if you are viewing a Web site, and your colleague needs to open a program on the computer, use then view the same Web site by just switching users after your colleague finishes with the computer.

If you select files before logging off the computer.

start

Control Panel

User Accounts.

Create a new account

account, then that user account has limits for using the computer. See

User Accounts

Switch User

Log Off

If Classic view is selected, double-click

and

Log Off

, you can pass the computer to another person without

, the system will close all your session and you need to save your

My Documents

for more details.

dialog box; then, the

folder etc., and save them to his/her user

Create Account

User Accounts

. If you have selected a

Control Panel

window.

Switch User

. You can

2-24

1. Click

2. Select you to save your data may appear.

3. Select another account to start Windows XP again.

start

Log Off

Switch User

If you cannot see

Change the way users log on or off

Use Fast User Switching

check

Log Off

Switch User

. If you select

Log Off Windows

and click

Log Off

User Accounts

Apply Options

, the dialog box, which asks

dialog box, click

dialog box, and

Set Password to User Account

You can set a password to each user account to avoid unauthorized use of your computer. Once you set the password, you need to enter it when you log on to your account. If you loose the password, you cannot start the computer with that user account, so unnecessary password setting can cause trouble in starting the system.

Setting Password

1. Click

2. Click icon.

3. Select the account you want to set a password to. You will only have this option if you log onto the computer as a member of the Computer administrators group. If you log on the computer with a limited user account, skip this step. (You cannot set a password to another user account.)

4. Select

5. Type a new password.

6. Type the new password again to confirm it.

7. If necessary, type a password hint word to remember the password you set.

8. Click

9. Close the

start

Control Panel

User Accounts.

Create a password

•

If the password has been already set, appear.

•

Only the members of the Computer administrators group can set a password to another user account.

Create Password.

User Accounts

If Classic view is selected, double-click

Create a password

dialog box; then, the

Control Panel

User Accounts

will not

window.

2-25

Changing Password

1. Follow the steps 1-2 on

2. Select the account you want to change, if you log on to the computer as a member of the Computer administrators group. If you log on the computer with a limited account, skip this step. (You cannot change the password for another user account.)

3. Select

4. Type a new password.

5. Type the new password again to confirm it.

6. If necessary, type a password hint word to remember the password you set.

7. Click

8. Close the

Deleting Password

1. Follow the steps 1-2 on

2. Select the account you want to delete, if you log on to the computer as a member

3. Select

4. Type your password and click

5. Close the

Change my password or Change the password

•

If the password has not been set yet,

the password

•

Only the members of the Computer administrators group can change the password of another user account.

Change Password.

User Accounts

of the Computer administrators group. If you log on the computer with a limited account, skip this step. (You cannot delete the password of another user account.)

Remove my password or Remove the password

•

If the password has not been set yet,

the password

•

Only a member of the Computer administrators group can delete the password of another user account.

a member of the Computer administrators group and want to delete the password of another user account, just click

User Accounts

Setting Password

will not appear.

dialog box; then, the

Setting Password

will not appear.

Remove Password

dialog box; then, the

section.

Change my password or Change

Control Panel

Remove my password

. If you log on the computer as

Control Panel

window.

Remove

2-26

CHAPTER 3

Battery and Power Management

This chapter explains how to manage the computer’s power effectively and use the battery pack.

In this section, you often see the expression “ dialog box”. To open the dialog box:

1. Click

start

Control Panel.

Performance and Maintenance

Click Category view or double-click view.

Battery Pack

When not connected to an external power source, your computer operates with the rechargeable battery pack. The duration of the battery life may be longer if the computer’s Power Management is active. See the next section for power management.

To keep the battery life long:

Condition (see “

•

the actual remaining power in your battery is less than what Windows Power Meter indicates.

Conditioning the Battery Pack”

Power Options Properties

Power Options

in this chapter) the battery pack if

icon in Classic

Turn off your computer when you are not using it.

•

The duration of the battery depends on the computer usage. Using

•

applications, which heavily use the optical drive or external peripherals, will result in shorter battery life. When using the computer for several hours with battery packs, enable

•

power management and set

Management

section in this chapter.

System hibernate

. Refer to the

Power

3-1

•

When the battery has not been charged, your computer may not operate properly. Connect the AC power to charge the battery.

Charging the Battery Pack

1. Connect the AC adapter to the computer. While the battery is being charged, the battery status indicator turns orange.

2. When the battery is fully charged, the battery status indicator turns green. Charging time may vary according to the status of the computer.

•

Battery status indicator may turn off even while the battery pack is being charged. This is either because the battery pack is hot or else the system power consumption is very high due to using the optical drive or CPU-intensive application, and the charging stops temporarily.

When the battery becomes cool, the charging will start and the battery status indicator will turn on again.

•

The battery pack may not be installed correctly if the battery status indicator blinks orange. In this case, turn off the computer, remove the AC adapter and the battery pack; then, install the battery pack and connect the AC adapter again. If the battery status indicator still blinks orange, ask your local dealer for assistance.

•

When the battery pack is hot (for example, after a long usage), it may take longer to be fully charged.

Checking the Battery Level

You can check the battery level by pointing to the battery or AC plug icon on the taskbar, or double-clicking the icon to open the is fully charged, remaining capacity level will not appear even if you point the icon.

If you cannot see the battery or AC plug icon, follow the instructions below:

1. In the

2. Check

3. Close the

Power Options Properties

Always show icon on the taskbar

Control Panel

•

The remaining operating time depends on the power you are consuming. If you are using the audio system, hard disk drive, any of the PC, SD and smart media card slots, any peripherals, floppy disk or optical disk, your computer may consume more battery life.

•

If the actual remaining power in your battery is less than what Windows Power Meter indicates, you should condition the battery pack as per the procedure on

window.

Power Meter

dialog box, select

and click OK.

Conditioning the Battery Pack

dialog box. If the battery

Advanced

tab.

section.

3-2

Low Battery Indication

When the battery power becomes significantly low (under 10%), the battery status indicator computer, or connect the computer to AC power immediately. Otherwise, the computer will be shut down and the data may be lost. To stop the warning beep sound, press Fn +

In Windows XP, the alarm will tell you when the battery drops to the specified level by sounding an alarm or displaying a message, and let your computer go on

standby/hibernate

To set Windows battery alarm:

1. In the

2. Set the battery level at which the alarms are activated. We recommend you set

Critical battery alarm Critical battery alarm

3. Set the

4. Click OK twice.

5. Close the

blinks red, the warning beep sounds. Save your data and turn off the

(

)

F10

Battery Status Indicator

or shut down automatically.

Power Options Properties

to 5 % or more and .

Alarm Action…

Control Panel

to the appropriate settings.

window.

dialog box, select

Low battery alarm

Alarms

tab.

to more than that of

System

3-3

Conditioning the Battery Pack

You need to condition the battery pack when the actual remaining power in your battery is less than what Windows Power Meter indicates, or you buy a new battery pack.

1. Make sure the computer is turned off. Connect the computer to AC power and wait until the battery is fully charged. The battery status indicator turns orange first; then, turns to green when the battery pack is fully charged.

2. Turn on the computer.

3. When the message to open the Setup Utility.

4. Disconnect the AC adapter, and leave the computer on until the battery is

completely discharged and the system shuts down automatically.

5. Connect the computer to AC power and let the battery fully charged again.

6. Turn on the computer and follow the steps 3 to 5 again.

7. Restart the computer. The conditioning process is complete.

Do not connect the computer to a wall outlet while discharging the battery. The conditioning will be cancelled.

Changing the Battery Pack

The capacity of a battery pack gradually decreases when used repeatedly (the deterioration rate depends on the operating environment). If the battery life becomes extremely short even after the conditioning, you should buy a new battery pack. Ask your local dealer for a new battery pack.

When you replace the battery pack with a new one:

1. Turn off the computer and disconnect the AC adapter from the computer.

2. Close the display cover and turn over the computer on a flat place.

<F2> to enter System Configuration Utility

appears, press F2

3-4

3. Slide the battery lock lever to the unlocked position ( ).

Battery Lock Lever

4. Slide the battery release lever to the unlocked position ( ) and hold it; then, pull out the battery pack slightly.

5. Lift up the battery pack and remove it from the computer.

6. Insert a new battery pack into the computer.

Battery Release Lever

3-5

7. Push the battery pack until you hear the clicking sound.

8. Set the battery lock lever to the locked position (

Battery Lock Lever

9. Turn over the computer and it’s ready to use.

3-6

Power Management

Power management saves electricity and extends battery life by controlling power supply to built-in devices. You can set the following power management properties in Windows XP.

Stopping power supply to the hard disk

•

Stopping power supply to the display

•

Using System standby/hibernate

•

To open

Performance and Maintenance

double-click

Power Options Properties

Power Options

Note that the power management may not seem to function when you are using an application program that accesses the hard disk periodically.

dialog box, click

; then,

icon.

Power Options.

Stopping Power Supply to the Hard Disk

1. In the

2. Set

3. Close the

Power Options Properties

Turn off hard disks

Control Panel

to an appropriate value, and click OK.

window.

dialog box, select

Stopping Power Supply to the Display

This procedure is also effective for a connected external monitor complying with power management.

1. In the

2. Set

3. Close the

Turn off monitor

Power Options Properties

to an appropriate value, and click OK.

Control Panel

window.

dialog box, select

–

start

Control Panel

If Classic view is selected,

Power Schemes

, and click

tab.

3-7

Using System Standby/Hibernate

System standby/hibernate

your computer has entered quickly when compared to a restart, after a normal shutdown operation. When your computer resumes from state of the computer. In Windows XP, you can define

hibernate

•

the system enters under what conditions.

System standby

power supply to all but a few essential components. Your system enters and resumes from

standby

from

System standby

, the Power indicator or the battery power indicator blinks green. To resume

is a very useful power management tool. For example, after

System standby

System standby/hibernate

stores the current condition of the computer in RAM and stops

per the conditions mentioned later. In

, operate the computer again.

mode, you can restart your computer more

, the system restores the exact last

System standby or System

System

System hibernate

•

disk and turns off the computer. Your system enters and resumes from

hibernate

indicator or the battery power indicator turns off. To resume from

hibernate

saves the current condition of the computer in an area of the hard

per the conditions mentioned later. In

, press the power button.

System hibernate

When entering/resuming from instructions below:

Finish communications, printing, and playing music or video before

•

entering Do not operate the computer or peripheral devices, or

•

connect/disconnect peripheral devices, while entering/resuming from

System standby/hibernate.

While operating with a battery, the computer may not resume from

•

System standby/hibernate

case, connect the AC adapter to your computer. Save your data before your computer enters

•

power supply to the computer is stopped, the RAM contents will be lost. Select your user account if Windows requires when the computer has

•

resumed from

System standby/hibernate

if the battery capacity is not enough. In this

System standby

System

, the power

System

, follow the

. If the

3-8

Supporting System Hibernate

If your battery becomes completely discharged during you will lose unsaved data and will need to reboot your computer. Therefore, if you are planning to leave your computer powered by battery for long periods of time, we recommend

Confirm that

1. In the

2. Confirm

3. Click OK.

4. Close the

Set Timer to Enter System Standby/Hibernate Automatically

Your computer will enter System standby/hibernate automatically when the specified time has passed without any operation. To set the time:

1. In the

2. Set the time after which the computer will enter System standby/hibernate in

System standby

3. Click

4. Close the

Entering System Standby/Hibernate

Your computer enters

You select

•

Turn off computer Computer

System hibernate

Power Options Properties

Enable hibernation

Control Panel

Power Options Properties

OK.

Control Panel

System standby/hibernate

Stand By or Hibernate(

dialog box. To open the dialog box, click

is supported with the following steps.

dialog box, select

is checked.

window.

dialog box, select

System hibernates

window.

which will appear if you press

System hibernate.

Hibernate

Power Schemes

in one of the following cases:

System standby

tab.

key) in the

Shift

start – Turn Off

The specified time in

•

Power Options Properties

previous section.)

The screen cover is closed

•

The above functions if you perform the following:

1. In

2. Select

3. Click OK.

the Power Options Properties

Hibernate

System standby or System hibernates

dialog box has passed without any operation. (See the

dialog box, select

Stand by

When I close the lid of my portable computer

Power Schemes

Advanced

tab.

tab

3-9

4. Close the

You press the power button.

•

The above functions if you perform the following:

1. In the

2. Select

computer

3. Click OK.

4. Close the

Control Panel

Power Options Properties

Hibernate

Control Panel

Stand by

window.

When I press the power button on my

window.

dialog box, select

Advanced

tab.

You press Fn +

•

The above functions if you perform the following:

1. In the

2. Select

3. Click OK.

4. Close the

The battery level is low.

•

The above functions if you set the alarm in Windows XP. See

Indication

Power Options Properties

Hibernate

computer

Ask me what to do

button

appear when you press the power button or Fn + You can select System standby or System hibernate at that timing.

in this chapter.

F12

Control Panel

You press Fn +

Disabling Power Management

1. In the

2. Set

3. Close the

Power Options Properties

Turn off monitor, Turn off hard disks, System standby

, and click OK.

Never

Control Panel

dialog box, select

Stand by

window.

When I press the sleep button on my

window.

is selected in the step 2 of

the

F12

dialog box, select

Advanced

You press the power

Turn off computer

F12

Power Schemes

tab.

dialog box will

key combination.

Low Battery

tab.

, and

System hibernates

3-10

CHAPTER 4

Peripherals

This chapter describes how to use peripheral devices with your computer. You can connect a printer, external monitor, or other devices to your computer. To ensure proper use, be sure to read the instructions for each peripheral device before connecting it to your computer.

Using Peripherals

You can use the peripheral devices shown on the next page. For the details, refer to the section explaining each device, or contact your dealer.

•

Be sure to turn off the computer and the peripheral device before connecting them (except when connecting USB devices, IEEE1394 devices or inserting a PC card).

•

Confirm the peripheral device you will connect is Windows XP compatible.

•

Some devices have to be turned on after the computer is turned on.

•

Some devices require that you install drivers before use.

4-1

Audio Equipment (S/PDIF compliant)

Peripheral Connection Overview

PC Card

Microphone

IEEE 1394

USB Devices

Device

External Monitor

Printer

Video Equipment with S Video connector

4-2

Display

You can use an external monitor with your computer. To display images on both displays simultaneously, use the 1024x768 resolution.

•

Some monitors, which are not compatible with your computer, may not display correctly.

•

In this section, you often see the expression “ box.” To open the dialog box, right-click somewhere on the Windows desktop and select

Connecting External Monitor

1. Turn off the computer and the external monitor.

2. Connect the computer and the external monitor. If the cable has screws, be sure to tighten them.

Properties

External Monitor Port

from the pop-up menu.

Display Properties

dialog

Screw

3. Turn on the external monitor; then, the computer.

Be sure to turn off the computer and the external monitor before disconnecting them.

4-3

Displaying the Screen on an External Monitor

To display the screen on an external monitor, you may need to install the driver for your external monitor. Before using the external monitor, refer to the manual included with your external monitor.

Switching the Display

1. In the

2. Select

3. Select the appropriate mode in

4. Click OK twice; then,

5. Click

Display Properties

button.

Utility Manager

•

When displaying on the LCD monitor: Set

•

When displaying on the external monitor:

Set

•

When displaying on both monitors simultaneously:

Set

twice.

•

You can also switch the display with

•

While playing video or animation, you may not be able to switch the display.

•

When displaying on both of the LCD monitor and the external monitor simultaneously, the external monitor should be capable for displaying in 1024 images on the external monitor properly.

•

To change the resolution and colors, refer to Chapter 2.

Driver mode

Driver mode to Single

Driver mode

dialog box, select

tab; then,

Yes

768 resolution or more. Otherwise, you may not display

Driver Mode Settings

Driver mode

Single

Mirror.

Primary

and

Primary to VGA.

and

Settings

section.

Fn+F5

tab; then, click

icon.

LCD.

Adjusting the Display

Advanced

4-4

Audio System

You can output sound to speakers, audio equipment or a headphone.

Connecting Speakers

You can connect stereo speakers with an amplifier to the audio output jack on the rear side of the computer.

Audio Output Jack

Speakers with an Amplifier

Connecting Digital Audio Equipment

The audio output jack of the computer is compliant with S/PDIF (Sony/Philips Digital Interface). You can connect a S/PDIF compliant audio equipment to the computer and output/record the sound.

Audio Output Jack

S/PDIF Compliant Optical Audio Cable

When recording sound with an audio equipment:

•

Use AC adapter for the computer and the digital audio equipment.

•

Exit other application programs.

•

Disable Windows power management.

S/PDIF Compliant Audio Equipment

4-5

•

(R)

Do not enter System standby/hibernate.

•

Do not operate the computer.

•

Use the digital audio equipment compliant with sampling rate of 48kHz.

•

Sound may not be recorded correctly if you use the synchronized recording system of the digital audio equipment.

Connecting Analog Audio Equipment

Audio Output Jack

You can adjust the output volume in Windows XP by double-clicking the speaker icon on the taskbar or use Fn + F3 or F4 keys combination.

Connecting Headphone

Use headphones with an impedance of more than 8Ω (32Ω is recommended).

Audio Out

ut Jack

White

(L)

Red

4-6

Connecting a Microphone

You can input sound using an external microphone connected to the microphone jack. Use an electret condenser microphone with an impedance of 2.2kΩ and an allowable voltage of 2.5V.

Microphone Jack

To record sound:

1. Click

2. Click

3. See

; then, point

start

Sound Recorder

for

Help

Sound Recorder

All Programs – Accessories – Entertainment.

for more details.

4-7

USB Device

Your computer has an interface called Universal Serial Bus (USB). With a USB connection, you can connect/disconnect peripherals without turning off the computer. Generally, when you connect a device to the computer, the necessary driver will be installed automatically. See also the manuals of peripheral devices supporting USB.

When a new device is correctly connected to the computer, the appropriate driver is automatically installed. If the driver is not installed correctly, you will see the message in the lower right of the screen. In this case, install the driver by following the instructions on the screen.

USB Ports

To remove USB devices, you may need to perform the following before you remove them:

1. Click

2. Click

3. Remove the USB cable from the computer.

Safely Remove Hardware

icon, click Step 3.

To Remove Hardware

to show all kinds of icons. If the icon does not appear, go to

Safely remove xxxxxxx

dialog appears.

icon (

. (

xxxxxxx is the name of the USB device)

) on the taskbar. If you cannot find the

; then,

Safe

4-8

PC Card

Your computer is equipped with a PC card (PCMCIA) slot, which can accommodate a Type II or a CardBus compliant card. You can insert/eject a PC card without turning off the computer. Before inserting a PC card into your computer, refer to its manual.

Inserting a PC Card

When a new card is correctly inserted, the appropriate driver is automatically installed. If the driver is not installed correctly, you will see the message in the lower right of the screen. In this case, install the PC card driver by following the instructions on the screen.

1. Confirm the PC card eject button is inside the computer cabinet. If the button is not inside the computer cabinet, push it back into the computer.

Eject Button

2. Insert a PC card into the slot with the label face up until it locks into place.

Label Face Up

4-9

If the dialog box asking you task you want.

What do you want Windows to do?

appears, select the

Ejecting PC Card

•

Some PC cards may become hot after long use

•

Be sure to follow the instructions below when ejecting a PC card. Otherwise, the system may not work properly

1. Click the the icon, click

2. Click

Remove Hardware

3. Push the PC card eject button so that it pops out from the side of the computer.

Safely Remove Hardware

to show all kinds of icons.

Safely remove xxxxx

dialog appears.

. (xxxxx is the name of your PC card); then,

icon (

) on the taskbar. If you cannot find

Safe To

Eject Button

4. Push the eject button and remove the PC card.

5. Push the PC card eject button all the way inside the cabinet for safekeeping.

4-10

Printer

You can connect a printer to the parallel port or the USB port.

Before using a printer, read the printer manual and install the printer driver.

Connecting to Parallel Port

1. Turn off the computer and the printer.

2. Connect the computer and the printer with the printer cable. If the connector has screws, tighten them.

Parallel Port

Screw

3. Turn on the printer; then, computer.

Printer Cable

Connecting to USB Port

Be sure to read the printer manual before connecting the USB printer to the computer. Some printer may not use install the printer driver.

You can connect the USB printer to the computer without turning off the computer.

New Hardware Find

wizard to

4-11

Using IEEE1394 Devices

You can connect the IEEE 1394 devices to the IEEE1394 port on the rear side of the computer. The IEEE 1394 is a digital interface for handling digital video, digital audio and other data in two directions between devices, and for controlling other equipments.

When two or more IEEE 1394 compatible devices are connected to the computer in a daisy chain, operations and data transactions are possible with not only the equipment that is directly connected, but also with other devices via the directly connected device.

•

Confirm the IEEE 1394 device you will connect is Windows XP compatible.

•

Use AC power for the computer and the IEEE 1394 device especially

Connecting IEEE 1394 Device

1. Attach the provided core to one end of your DV (IEEE1394) cable. Insert the cable into the core and put the cable around the core; then, close the core until it clicks.

when reading/writing the data.

•

Some IEEE 1394 devices require that you install drivers before use.

•

Attach the provided core to the DV(IEEE1394) cable to insure compliance with requirements of EMC regulations for computing equipment.

•

You need not turn off the computer before connecting the device.

•

Be sure to read the manuals of the IEEE 1394 device before connecting it to the computer.

4-12

Core

2. Connect the core end of the DV cable into the IEEE 1394 connector of the computer and the other end into the DV connector of the IEEE 1394 device.

IEEE 1394 connector

To IEEE 1394 Compliant Device

DV Cable

3. Install the driver according to the instructions on the screen. Generally when you connect the device to the computer, the necessary driver will be installed automatically.

4. Start the appropriate application for handling your data.

Disconnecting IEEE 1394 Device

1. Click the the icon, click Step 3.

2. If the name of your device appears, click of your IEEE 1394 device.); then,

3. Remove the DV cable from the computer.

Safely Remove Hardware

to show all kinds of icons. If the icon does not appear, go to

icon ( ) on the taskbar. If you cannot find

Safely remove xxxxx

Safe To Remove Hardware

(xxxx is the name

dialog appears.

4-13

4-14

CHAPTER 5

Communication Functions

This chapter explains how to use the built-in modem and the LAN unit.

Built-in Modem

You can use the built-in modem for data transfer and fax communication.

•

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

•

The built-in modem on your computer is designed only for regular analog telephone lines. The modem may be damaged when connected to a digital ISDN terminal or a digital PBX.

•

Use TA (terminal adapter) to connect the built-in modem to a digital telephone line.

•

If an unusual device is attached to the line you are connecting to, the modem may not function properly. Remove the device or contact the dealer of the device.

•

Before connecting to a PBX, consult the PBX maintenance staff or its service company. If the electric characteristics of your PBX are different from those of a regular analog line, the modem will not function properly. If you connect the modem to a digital PBX, both the modem and the PBX may be damaged.

5-1

Connecting the Modem to a Telephone Line

1. Turn off your computer.

2. Connect the core end of the included modem cable to the modem jack (with mark) on the rear side of the computer. Connect the other end of the modem cable to the telephone line.

Core

To Telephone Line

Modem Jack

Modem Cable

Be sure not to insert into the LAN jack (with both the modem cable and the LAN jack.

3. Turn on the computer.

Connect the modem to the telephone line directly. Do not use a distributor or allotter.

mark

It may damage

Configuring the Modem

You may have already configured your modem during Windows XP Setup process. Otherwise, make the necessary adjustments as shown below.

Modem Configuration

When you use the modem first time, you must type your location’s information.

1. Click

2. Click

view is selected, double-click

5-2

start

Control Panel

Printers and Other Hardware

Phone and Modem Options

; then,

Phone and Modem Options.

If Classic

icon.

3. In

Location Information

and select your dial type; then, click

4. Close the

Next time you click or double-click

Options

previous page by double-clicking the location name of You can change the settings or make a new location by clicking

Internet Connection

Windows XP has a special Internet Connection Wizard to help you to connect to the Internet with ease. Click

Connections Network Connections connection

follow the instructions on the screen. If you plan on connecting to the Internet by using the modem to dial an Internet Service Provider (ISP), have your account information and dial-up number ready before you begin the wizard. Once you set your connection, you can see or edit the connection status by double-clicking the icon appearing on

Power Management

To use the communication software, you may have to disable power management. See

Disabling Power Management

Control Panel

dialog box appears. You can find the information you set in the steps on the

; then,

Network Connections.

Network Tasks

Dial-up

•

See also the manual or online help of the software you are using

•

Within the communications software you are using, set the COM port of the built-in modem to COM3.

•

Do not enter software.

•

The communication speed may vary depending on the traffic, local telecommunications infrastructure, and ISP (Internet Service Provider) infrastructure.

•

Before commencing with fax communication, it is recommended that you exit other application programs.

dialog box, select your country, type your area code, etc.,

twice.

window.

Phone and Modem Options, Phone and Modem

tab.

Edit …

Create a new

dialog box appears,

–

start

Control Panel

icon. In

Network Connections

. When the

Network Connections

of Chapter 3.

System standby/hibernate

Dialing Rules

. Click

Network and Internet

If Classic view is selected, double-click

dialog box, click

New Connection Wizard

dialog box.

while using communication

New

….

5-3

LAN unit

You can connect to a LAN (Local Area Network) with the 100 Base-TX/10 Base-T LAN unit on your computer. To activate the LAN unit, perform the following steps.

Use a category 3 or a category 5 LAN cable when connecting to 10 BASE-T LAN, and the category 5 when connecting to 100 BASE-TX LAN.

Connect your computer to LAN

1. Turn off the computer.

2. Attach the provided core to one end of your LAN cable. Insert the cable into the core and put the core around your LAN cable; then, close the core until it clicks.

3. Remove the cover of the LAN jack on the rear side of your computer.

Core

LAN Jack

5-4

4. Connect the core end of the LAN cable into the LAN jack (with connect the other end of the LAN cable into the network hub.

LAN Jack

LAN Cable

Do not insert into the LAN cable to the modem jack (with will damage the LAN cable and the modem jack.

5. Turn on the computer.

6. Click

7. Click

If you cannot access the network,

1. Click

2. Click

3. Click

4. Double-click

5. Click

6. Click OK and close the

7. Click OK.

8. Close the

start - Control Panel

Network and Internet Connections

view is selected, double-click according to the instruction of your network administrator.

Attach the provided core to your LAN cable to insure compliance with requirements of EMC regulations for computing equipment.

start - Control Panel

Performance and Maintenance

double-click

value in

System

Hardware

Network adapters

Advanced

Value

Control Panel

tab; then,

tab, and select

Network Connections

icon.

Device Manager

window.

; then,

System.

button.

, then,

SiS 900-Based PCI Fast Ethernet Adapter

Media Type

window.

To Network Hub

Network Connections.

icon. Set the network setting

If Classic view is selected,

Property

and select an appropriate

mark) and

mark). It

If Classic

5-5

5-6

CHAPTER 6

Setup Utility

This chapter describes how to run the Setup Utility to change settings on your computer.

Running the Setup Utility

With the Setup Utility, you can customize the system configuration information, such as time and date, port assignments, or passwords. The information you have specified is saved in a special area called CMOS RAM, which the system reads every time you turn on the computer. Your computer is shipped from the factory with the appropriate setting of the Setup Utility. Leave it as default in normal use.

Contents of the Setup Utility

The Setup Utility consists of four menu pages, as follows:

Main: Configures basic setting

•

Advanced: Configures device interface (I/O ports, etc.)

•

Security: Sets Passwords

•

Exit: Exits the Setup Utility or returns to the default values

•

6-1

Entering and Exiting the Setup Utility

1. Turn on the computer.

2. When

3. Set the settings to the appropriate ones. Refer to the next section.

4. Select

5. Select one of the exit methods, and press

6. Confirm the message and press

<F2> to enter System Configuration Utility

Utility opens.

menu; then press

Exit

Enter

Changing the setting of the Setup Utility

To change the settings:

1. Use → or ← key to select the menu; then press

2. Use ↑or ↓ key to select the item.

If the item has or :

Press enabled. Mark means disabled.

If the item has no mark (except of

Security

1. Press

2. Use Tab key to highlight the value; then use ↑ or ↓ key to select the value. The value with • is being selected.

3. Use Tab key to highlight OK; then press

To set

Date and Time

1. Press

2. Use arrow keys to highlight the value; then use minus key or space bar to change the value.

3. Use arrow keys to highlight OK; then press

To set

Set Password

3. Close the Setup Utility according to the steps above.

When the Setup Utility is opened, power management does not work. Do not close the display cover.

to enable or disable the item.

Enter

Date and Time

menu):

to open the sub menu.

Enter

: see

Security Menu

appears, press F2. The Setup

Enter

again. The system restarts.

Enter

mark means the item is

Enter

in this chapter.

Main

Enter

menu and

Set Password

6-2

Main Menu

Date and Time

and minus key or space bar to change value.

Hard Disk Type

show the details. Leave it as default in normal use.

Boot Sequence

menu. The system boots from the drive selected in cannot find the drive, it will boot from the drive selected in drive selected in

Internal Numlock

not. If you will use the keypad area of the external keyboard only, set it to

Hot Key Beep

simultaneously pressed.

defines the system date and time. Use arrow keys to select the value,

shows the type of the hard disk of your computer. Press

specifies where the system boots from. Press

1st Boot Device.

2nd Boot Device

3rd Boot Device

defines whether Fn +

defines whether the beep sounds when Fn +F5-F8,

NumLk

key combination always works or

to open the sub

Enter

If the system

F10-F12

Enter

; then, the

Disabled.

keys

6-3

Advanced Menu

LPT Port

means that you cannot use the port. (Extended Capabilities Port mode),

Only

Internal Pointing Device

Shared Video Memory

with the extended memory.

TV SYSTEM

Battery Low Warning Beep

remaining capacity becomes extremely low (this item does not work for Windows battery alarm).

LAN Boot

LAN is activated.

Wake On LAN

LAN unit of the computer becomes active.

Wake On Ring

built-in modem receives a call.

sets the printer port, selecting the base I/O address and IRQ.

can be selected from

Mode

(Enhanced Parallel Port mode) or

EPP

enables or disables the built-in glide pad.

defines the size for the video memory which will be shared

switches TV type between PAL and NTSC.

enables or disables the beep sound when the battery

defines whether the system boots from the PXE server when the integrated

defines whether the system resumes from System Standby when the

Bi-Directional, ECP

Disabled

Output

6-4

Security Menu

Set Password

about the password setting.

Hard Disk Virus Protect

protected. When formatting the hard disk or reinstalling software, set it to disabled.

Password

Setting a password will protect your computer against unauthorized access. When a password is set, the system requires the password when entering the Setup Utility. And if

Password On Boot

computer is turned on. Refer to the next section.

Setting the Password

1. In the

2. Type your password (up to eight characters), and press

3. Type the same password again, and press

defines the password (up to eight characters). See the next section

If you lose your password, you will be unable to access the computer or change the configuration. Make sure to select a password you will never forget, or write it down and protect it in a secure place. Otherwise, you will have to contact your dealer for assistance.

defines whether the boot sector of the hard disk is write-

is enabled, the system will require a password when the

If you enter a wrong password three times, the message “

incorrect. System will be shut down”

the computer, and after 10 seconds, press the power button to turn it on again.

Security

menu of the Setup Utility, select

appears. Press

Set Password

Enter

The password is

to shut down

Enter

and press

Enter

4. If you want the password required when booting, confirm

marked with

5. Use Tab key to highlight OK and press

6. Select

7. Confirm OK is highlighted and press

Enter

Exit

menu and confirm

Enter

Exit Saving Changes

. The system restarts.

Enter

is highlighted; then press

Password On Boot

6-5

Changing the Password

1. In the

2. Type your current password, and press

3. Type your new password, and press

4. Type your new password again, and press

Security

menu of the Setup Utility, select

Enter

Set Password

and press

Enter

5. If you want the password required when booting, confirm

marked with

6. Use Tab key to highlight OK and press

7. Select

8. Confirm OK is highlighted and press

Enter

Exit

Deleting the Password

1. In the

2. Type your current password, and press

3. Without typing any characters, press

4. Press

5. Select

6. Confirm OK is highlighted and press

Enter

Security

Enter

Exit

menu and confirm

menu of the Setup Utility, select

twice.

menu and confirm

Exit Saving Changes

Enter

Exit Saving Changes

Enter

is highlighted; then press

. The system restarts.

Set Password

Enter

is highlighted; then press

. The system restarts.

Password On Boot

and press

Enter

6-6

Exit Menu

Exit Saving Changes

Exit Discarding Changes

changed.

Load Setup Defaults

of the above items.

Discard Changes

select one of the above two items.

Save Changes

two items.

saves the settings you have changed and exits the Setup Utility.

exits the Setup Utility without saving the settings you have

returns the values of all items to the default. To exit, select one

returns the values of all items to the values you last saved. To exit,

saves the settings you have changed. To exit, select one of the above

6-7

6-8

Appendixes

The appendixes contain additional information on the use and care of your computer.

Memory Module

You can expand the memory size up to 512MB by installing a memory module(s) of 128MB or/and 256MB. For an available memory module, ask your local dealer. A 512MB model is not memory expandable. See the specification on the provided Supplement for the memory size of your computer.

Installing a Memory Module

•

Do not handle the memory module where static electricity is easily generated such as on the carpet.

•

Before installing the memory module, carefully discharge static electricity from your body by touching an unpainted metal area.

•

Avoid touching the integrated circuits on a memory module. Handle all components by the edges.

•

Keep the memory module in the anti-static wrapping until you are ready to install it.

1. Turn off the computer, and disconnect the AC adapter and remove the battery pack and peripheral devices. See Chapter 3 for removing the battery.

•

Make sure to turn off your computer and remove the AC adapter. Otherwise you may get an electrical shock.

•

After a long usage of the computer, the temperature inside the computer may be hot. Wait until it becomes cool.

Appendixes

A-1

2. Loosen two screws and remove the memory slot cover.

Screw

Memory Slot Cover

3. Turn over the sheet and align the memory module as shown below, matching the notched part of the module with the projected part of the memory socket of the computer.

Sheet

Appendixes

Notched Part

Projected Part

Memory Module

20°

Memory Socket

4. Press the memory module softly to place it into the memory socket, matching the notched parts of the module with the projected parts of the memory socket, until you hear the clicking sound.

Projected Part

A-2

Notched Part

5. Replace the sheet and the memory slot cover to the computer matching the

projected parts of the cover with the notched parts of the computer.

Pro

6. Tighten the screws.

ected Part

Notched Part

7. Replace the battery pack, turn over the computer and connect the AC adapter.

8. Turn on the computer and check the memory size by clicking

computer – View system information of System Tasks

appear at the bottom of the sentence. Share video memory size will not be included with the value.

Screws

start – My

. Your memory size will

Appendixes

A-3

Uninstalling the Memory Module

1. Follow steps 1-2 of

2. Slightly bend the two latches outward until the memory module is released.

3. Remove the memory module and follow steps 5-8 of

Module

Installing the Memory Module

and turn over the sheet.

Installing the Memory

Maintenance and Care

This section provides you with information on how to maintain the computer in excellent working condition.

Replacing Backup Battery

Appendixes

•

Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type recommended by the equipment manufacturer.

•

Discard used batteries according to manufacturer’s instructions.

Your computer is equipped with a backup battery, which will keep the information of the Setup Utility, etc safe. If you see the message

CMOS default

be purchased from your local dealer.

1. Turn off the computer, and remove the AC adapter, the battery pack and peripheral devices. See Chapter 3 for removing the battery.

, replace the backup battery with a new one. A new backup battery can

Make sure to turn off your computer and remove the AC adapter and the battery pack. Otherwise the computer may malfunction.

Press F1 to Continue, Del to Load

A-4

2. Loosen the screw and remove it.

3. Lift up the cover softly and place it next to the socket.

Screw

Cover

Make sure to gently remove the cover, not with great force. The backup battery connected with the computer by the cable is attached to the back of the cover.

4. Unplug the cable pulling in a straight line from the computer.

Make sure to hold the part as near to the connector of the cable as possible when pulling out the cable.

Connector

Appendixes

A-5

5. Remove the backup battery out of the cover by pulling it out in the arrow direction.

6. Set a new backup battery into the cover.

7. Connect the cables of the battery to the computer.

Appendixes

A-6

Projected Part

Make sure to connect the cables with the projected part and the notched part of the cable connector face up. Otherwise, the computer and the battery may be damaged.

Notched Part

Black Cable

Connector

Red Cable

Cables

8. Replace the backup battery box cover to the computer.

9. Tighten the screw.

Screw

10. Insert the battery pack and turn over the computer.

11. Connect the AC adapter and turn on the computer.

12. If you see the message

Delete

key. The system starts.

13. Double-click the time appearing on the right of the taskbar.

14. Set the time and date in

15. Close the dialog box.

Press F1 to Continue, Del to Load CMOS defaults

Date and Time Properties

dialog box and click

Cover

, press

OK.

Appendixes

A-7

Using a Security Cable

You can connect a security cable to the security slot on the rear side of your computer to prevent theft.

Security Cable

Appendixes

Security Slot

Cleaning the Computer

Cabinet

Apply a small amount of mild cleaning solution to a dry, lint-free cloth and wipe the cabinet with the cloth.

•

A-8

Never clean the computer while it is powered on.

•

Do not use alcohol, benzene, thinner or other strong chemical agents that may damage the cabinet.

Screen

The surface of the screen may become smeared and accumulate dust during use. Avoid touching the screen with your fingers when using the system. Gently wipe the surface of the screen with a soft cloth that has been dipped in a mild detergent solution and squeezed dry.

Glide Pad

Wipe the glide pad with a soft, dry cloth.

Ventilation Openings

Dust on the ventilation openings may cause overheating of the computer. Wipe the ventilation openings with a soft, dry cloth.

Traveling with the Computer

This computer is designed for portability. For safety and convenience when traveling, please follow these guidelines.

•

Before traveling, back up your data on external media.

•

Do not carry the computer powered on. This may result in loss of data and/or damage to the hard disk drive.

•

Make sure the display cover is closed before traveling.

•

Disconnect the AC adapter from the computer.

•

Fully charge the standard battery pack and bring the AC adapter and the AC power cord with the computer.

•

Avoid sudden shocks or extreme vibration.

A-9

Appendixes

A-10

Troubleshooting

This chapter describes how to troubleshoot computer problems.

Common Problems

Problems with your computer can be caused by something as minor as an unplugged power cord or as major as a damaged hard disk drive. The information in this troubleshooting section is designed to help you find and solve minor problems. If you still have a problem after trying all the suggested remedies in this chapter, contact your dealer.

The problems that you might encounter can be divided into two basic categories: hardware and software. Hardware problems can be further divided into being of an electrical or a mechanical nature. You will know you have a hardware problem if, for example, the screen is blank, or the computer cannot recognize the disk drives.

Software problems can occur at several levels. Both your operating system and your software application programs are capable of generating errors and error messages. If you encounter a software error, try to determine if the error message is from your operating system or from an application program, and refer to the appropriate manual for possible remedies.

You can also refer to the Windows XP manual or Windows Help program to solve the problem. To access the Help program, Click start – Help and Support. It also gives you Troubleshooting tips and an Index.

Successful troubleshooting is the result of careful observation, deductive reasoning, and an organized approach to solving the problem. If you encounter a problem, begin by performing a careful visual inspection. Check the exterior of the computer first. If no lights are displayed, check the battery charge or power outlet, the plug and power cord, and any power switches that may affect your computer. If the computer has been connected to any peripheral devices, look for loose or disconnected cables. You may also need to check the fuses and breakers in your electric box. A few common problems and suggested solutions are presented in the examples which follow.

Troubleshooting

T-1

Trouble when Starting

Question: Why doesn't the power indicator or the battery status indicator turn on?

Make sure the AC adapter is correctly connected to the AC adapter jack of your

•

computer.

Make sure the AC power cable is correctly connected to a live wall outlet.

•

Connect another electric equipment to the wall outlet and check whether it is live or not.

Make sure the battery pack is correctly installed and charged.

•

If the battery pack is discharged, connect the AC adapter.

•

If all the steps above failed, follow the instructions on Why doesn't the keyboard

•

or the glide pad function?

Question: Why do I get the message

You may have inserted a non-bootable disk in the floppy disk drive (either a

•

defective disk or one without an installed operating system). Remove the disk.

Invalid system disk

Question: Why can’t I boot from the floppy disk?

Check whether the floppy disk set to the floppy disk drive contains a system disk.

•

Troubleshooting

Check whether Floppy Disk Drive is selected in 1st Boot Device in Boot Sequence

•

of the Main menu of the Setup Utility.

Question: Why do I get the message

CMOS defaults

Press<F1> to continue, Del to load

The setting of the Setup Utility is deleted. Press

•

time and date correctly.

If you often see the message, the backup battery has no capacity left. Replace the

•

backup battery referring to the steps in Replacing Backup Battery of Appendixes.

to start the system and set

Delete

T-2

Question: Why do I get the message

key for floppy

If you cancel the re-installation on the way, you will see the message above.

•

Restart re-installation form the beginning of Re-installation Instructions procedures of the provided Supplement and format the entire hard disk (both C: and D: drives) this time.

Press ‘H’ to retry Hard Disk, any other

Trouble with Display

See also the Display section of Chapter 2 and 4.

Question: Why is the screen blank?

Press any key to see if any power management feature has turned off the screen

•

to save power.

See the power indicator to check whether the computer is turned on.

•

If you are using a battery pack, make sure it is correctly installed and has a charge

•

remaining.

Make sure the LCD screen is selected as the display by pressing

•

Check whether the display is on by pressing

•

If you still have the problem after trying the above, follow the steps in Why

•

doesn't the keyboard or the glide pad function?

Question: Why does the external monitor display nothing or the image on it distorted?

Confirm the monitor is turned on.

•

Confirm the monitor is connected correctly.

•

If the television set is connected to the computer, disconnect it.

•

Make sure the external monitor is selected as the display by pressing

•

Fn+F11

Fn+F5

Troubleshooting

If you use Fn+F5 to change the display, the image may be distorted. Press Fn+F5

•

again to return the previous display and use Display Properties dialog box to change it again.

Make sure the value of the Screen resolution in the Settings tab of the Display

•

Properties is as same as that of the external monitor resolution or lower.

Make sure the external monitor is not near any electric devices having strong

•

magnetic fields such as a TV set or radio.

Do not share an outlet with a TV set or radio.

•

T-3

Sharp PC-GP2 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Notice for Users in the UK and Ireland

Notice for Users in Europe

Safety Precautions

About This Manual

Recording Important Information

Manual Conventions

Table of Contents

Overview of Computer

Quick Setup

Installing Battery Pack

Connecting AC Power

Setting Up Windows XP

Turning Off Your Computer

Basic Operations

Resetting the System

Using the Glide Pad

Using the Keyboard

Using the Floppy Disk Drive

Using the SD Card Slot

Using the Smart Media Card Slot

Using the Optical Drive

Controlling Audio

Adjusting the Display

Sharing the Computer

Battery and Power Management

Battery Pack

Power Management

Peripherals

Using Peripherals

Display

USB Device

PC Card

Printer

Using IEEE1394 Devices

Communication Functions

Built-in Modem

LAN unit

Setup Utility

Running the Setup Utility

Main Menu

Advanced Menu

Security Menu

Exit Menu

Appendixes

Memory Module

Maintenance and Care

Troubleshooting