Sharp PC-A810 User Manual

NOTEBOOK COMPUTER
PC-A810 Series
OPERATION MANUAL
â

Notice for Users in the USA

FCC Statement
WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide r easonable pr otection ag ainst harmf ul interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no gua rantee tha t interfer ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the distance between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
A shielded I/F cable and included cables with ferrite cores are required to insure compliance with FCC regulation for Class B computing equipment.
* As an ENERGY STAR® Partner, SHARP has determined that this
product meets the ENERGY STAR efficiency.
®
guidelines for energy
i
Declaration of Conformity
SHARP PERSONAL COMPUTER, PC-A810 Series This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:( 1)this device may not cause harmful interference, an d (2) this device must accept any interference received, including interference that may cause undesired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135 TEL: 1-800-BE-SHARP
About the Modem
This equipment complies with Part 68 of FCC rules. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
The modem jack of this equipment complies with Sub-part F of Part 68 of FCC rules.
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs contact the telephone company to determine the maximum REN for the calling areas.
If the terminal equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the
ii
equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact Sharp Electronics Corp. for repair and (or) warranty information (Refer to the end of this section). If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
The equipment cannot be used on public coin service provided by the telephone company. Connection to Party Line Service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.)
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) To program this information, refer to the manual of the communication software.
CAUTION: DISCONNECT TELEPHONE LINES BEFORE ACCESSING THE MODEM CARD.
Copyright
It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.
Product Information and Customer Assistance
For Product Information and Customer Assistance: Call: 1-800-BE-SHARP (237-4277)
iii
Sharp Electronics Corp. Sharp Plaza, Mahwah, NJ 07430-2135 Home Page: http://www.sharp-usa.com E-mail address: pcsupport@sharpsec.com
iv

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.
Η εγκατασταση αυτη ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ συµπληρωθηκαν απó την οδηγια
89/336/EOK
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av 93/68/EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
κατ
73/23/EOK, ó
93/68/EOK.
πωζ οι κανονισµοι αυτοι
v
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.
vi
CAUTION:
TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING.
CAUTION:
FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY.
VORSICHT:
UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN.
ATTENTION:
POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE.
VARNING:
FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH TA UR BATTERIET.
PRECAUCION:
PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED Y LA BATERIA.
vii

Safety Precautions

General
Follow all cautions and instructions which may be marked on the computer.
Except as described elsewhere in this manual, refer all servicing to qualified personnel. Immediately shut off the computer and seek servicing under the following conditions:
when the power cord or plug is damaged or frayed
if liquid has been spilled on the computer
if the computer has been dropped or the cabinet has been damaged
Location
Do not expose the computer to direct sunlight.
Try to avoid dusty environments.
Keep the computer away from any magnetic devices and TVs.
Keep the computer away from excessive humidity or fluids such as rain, snow, water spray, juice, coffee, steam, etc.
Do not move the computer from an extremely cold place to an extremely warm place. A temperature difference of more than 10°C (18°F) will cause condensation inside the unit, which may cause damage.
Do not block or cover slots or openings on the cabinet. These protect the computer from overheating.
Care should be exercised when using on heat sensitive surfaces or your lap as the base of this computer will get hot.
Do not smoke near your computer.
Usage
Never push any objects of any kind into cabinet openings. They may touch dangerous voltage points or short parts that could result in fire or electrical shock.
viii
Turn off the computer before installing or removing a peripheral device (except when connecting USB devices and PC cards).
Check the AC power cord and power connectors periodically for damage. Replace the power cord immediately if damage is found.
Never subject your computer to sudden shocks or extreme vibration.
Do not drop the computer nor hit it with other equipment.
Do not scratch the surface of the LCD screen.
Turn off the computer and disconnect the AC power cord before cleaning.
Battery Pack Precautions
Handling
Never put the battery pack in a fire, as it could explode and cause injury.
Do not attempt to open or alter the battery pack.
Do not place the battery where it might get hotter than 60°C (140°F).
Do not allow metal objects such as jewelry to short across the battery terminals, as it could heat up and explode.
Do not allow liquids to come in contact with the battery pack.
Avoid dropping the pack or other violent shock.
Do not solder anything to the battery terminals.
Charging
ix
Charge the battery pack only with the AC adapter included with your computer or an optional one.
Discharging
Do not use the battery pack for any purpose other than powering the computer.
Storage
Store the battery pack in a cool and dry place. Never allow the temperature to exceed 60°C (140°F) during storage.
Recharge the battery pack after storage, before use.
Modem Precautions
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
Use caution when installing or modifying telephone lines.
Avoid using the telephone during a lightning storm. There may be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak while in the vicinity of the leak.
x
About This Manual
Notice
Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation.
SHARP Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.
SHARP strongly recommends that separate permanent written records be kept of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other causes.
SHARP assumes no responsibility directly or indirectly, for financial losses or claims from third persons resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss of or alteration of stored data, etc.
Edition
1st Edition, February 2000.
Copyright
© 2000 SHARP Corporation This document contains or refers t o proprieta ry information which i s protected b y copyright. All rights are reserved. Copying or other reproduction of this document is prohibited without the prior written permission of SHARP Corporation.
Trademarks
Pentium is a registered trademark, and Celeron is a trademark, of Intel Corporation. IBM and PS/2 are trademarks of International Business Machines Corporation. Microsoft, MS-DOS, Windows, a nd the Windows Logo are registered trademarks of Micros oft Corporation. Sound Blaster is a trademark of Creative Technology Ltd. All other brand and product names are trademarks or register ed trademarks of their respective holders.
xi

Recording Important Information

For future reference, please record the following information in the spaces provided below.
Model Number:
Serial Number:
Date of
purchase:
Dealer’s Name:
Place of
purchase:
Password:
The serial number is printed on a sticker located on the bottom of the computer.
xii

Manual Conventions

This manual uses a set of style conventions described below. Notes and Cautions are italicized with icons:
A note icon informs you of a special technique or information that may help you perform a task or better understand a process.
A caution icon alerts you to something that may cause problems or damage to hardware, software or data.
Key Labels on the Keyboard, when referred to in the instructions, are shown in boldface: Press Enter to continue.
When two or more keys are pressed simultaneously, the key labels are separated by a plus (+) sign: Restart your computer by pressing Ctrl+Alt+Delete.
When necessary, important key combinations are shown in graphics:
Sample Entries are shown in upper cases of different typeface. In the following case, press the Enter key after you type the command: C:\>DIR A: Enter
Words/Texts on Screen, such as window titles or possible parameters, are italicized: Double-click this icon to display the Power Properties window. Set the item to Enabled.
Screens reproduced in this manual may differ slightly from the screens you see on your computer.
Section Titles in other parts of this manual are italicized:
xiii
Refer to Infrared Communication section in Chapter 5.
xiv

Table of Contents

Notice for Users in the USA .................................................................i
Notice for Users in Europe...................................................................v
Safety Precautions............................................................................ viii
About This Manual .............................................................................xi
Recording Important Information ..................................................... xii
Manual Conventions ........................................................................ xiii
Table of Contents...............................................................................xv
Overview of Computer................................................................... xviii
Fast Start 1-1
Connecting AC Power...................................................................... 1-1
Setting Up Windows 98................................................................... 1-3
Turning Off Your Computer............................................................ 1-4
Basic Operations 2-1
Powering the Computer.................................................................... 2-1
Resetting the System........................................................................ 2-3
Using the Keyboard.......................................................................... 2-4
Using the Glide Pad ......................................................................... 2-7
Reading the Status Indicators........................................................... 2-8
Adjusting the Display....................................................................... 2-9
Controlling Audio .......................................................................... 2-11
Using the Drives............................................................................. 2-12
Installing a Drive in the Drive Bay................................................. 2-14
Using the CD-ROM Drive............................................................. 2-15
Using the Floppy Disk Drive Externally........................................ 2-16
Battery and Power Management 3-1
Battery Pack..................................................................................... 3-1
Battery Low Warnings ..................................................................... 3-3
Battery Conditioning........................................................................ 3-4
Changing a Battery Pack.................................................................. 3-5
Programmable Power Management................................................. 3-6
Power Management Hot-keys........................................................ 3-10
xv
Connecting Peripherals 4-1
Using Peripheral Devices..................................................................4-1
Connecting Peripherals Overview....................................................4-2
Using PC Cards.................................................................................4-3
Connecting an External Monitor ......................................................4-6
Connecting Headphones.................................................................4-10
Connecting USB Devices...............................................................4-10
Connecting a Printer.......................................................................4-11
Communication Functions 5-1
Infrared Communication...................................................................5-1
Built-in Modem(may not available in some countries)....................5-4
Changing or Adding Options 6-1
Using the Recovery CD....................................................................6-1
Adding a Memory Module ...............................................................6-3
Using the Optional Port Replicator...................................................6-5
Security Features 7-1
Passwords .........................................................................................7-1
Using a Security Cable .....................................................................7-4
Setup Utility 8-1
Running the Setup Utility.................................................................8-1
Main Page.........................................................................................8-3
Advanced Page .................................................................................8-4
Security Page....................................................................................8-5
Power Page .......................................................................................8-6
Boot Page..........................................................................................8-7
Exit Page...........................................................................................8-7
xvi
Appendices
Appendix 1: Troubleshooting ..........................................................A-1
Appendix 2: Care & Maintenance....................................................A-8
Appendix 3: Specifications............................................................A-10
Index
Index.......................................................................................... Index-1
xvii
Overview of Computer
In the following diagram, the labels in italics refer to the chapter and page number in this manual where you can find more information. The actual appearance of your computer may be slightly different depending on the model.
Front View
LCD screen
See 2-9
Microphone
See 2-11
Keyboard
See 2-4
Glide pad
See 2-7
Glide pad buttons
See 2-7
Speaker
See 2-11
Front View Markings
System status indicators
See 2-8
Release latch for floppy disk drive
Battery & power indicators
See 2-2
Power button
Floppy disk drive in floppy disk drive box
See 2-13, 2-16
Battery
Power
Indicator
CD or
Hard disk
activity
Floppy
disk
activity
Num
lock
Caps
lock
Scroll
lock
indicator
xviii
Right Side View
PC card slot
See 4-3
PC card eject button
See 4-4
Left Side View
Drive bay with CD-ROM drive installed
See 2-15
Drive activity indicator
Manual tray eject button (recessed)
Eject tray button
Slot for security cable
See 7-4
K
Battery lock button
AC adapter jack
See 1-1
xix
Rear View
(may not be available in some countries)
Bottom View
Port replicator docking connector
See 6-6
Drive bay lock latch
Modem jack
See 5-4
Parallel/FDD port
See 4-11
Memory module compartment
See 6-4
Monitor port
See 4-6
Infrared port
See 5-1
USB port
See 4-10
Headphone jack
See 4-10
Reset switch (recessed)
See 2-3
CD-ROM drive installed in drive bay
See 2-14
xx
Battery
See 3-1, 3-5
xxi
CHAPTER 1

Fast Start

Your new computer is ready to use as soon as you unpack it from the box. If you’re familiar with computers, follow the instructions in this chapter to get your system up and running in just a few minutes. If this is your first computer, you should read through the entire Operation M anual before starting the system.

Connecting AC Power

Run your computer the first time using AC power, rather than battery power. This ensures that you will not lo se power while you complete the Windows setup operation.
Use only the AC adapter that was supplied with your computer,
or supplied by your computer vendor. You can damage your
Place your computer on a flat working surface and follow the steps below.
1. On the front edge of the computer, slide the cover latch to the right and raise the cover.
computer if you try to use an AC adapter that is not approved for use with this system.
When removing the AC power cord from a wall ou tlet, grip the
plug and pull it from the socket. Never remove the power cord from the outlet by pulling on the cord. Always grip the plug.
1
Cover latch
1-1
1
2. Plug the cable from the AC adapter into the AC adapter jack on the left side of the computer.
3. Connect the power cord to the AC adapter.
4. Plug the power cord into a suitable power outlet. The orange battery charge indicator turns on when you connect AC power.
Battery charge and power indicators
AC adapter jack
To power outlet
5. Press the power button located just above the Pause button on the keyboard. The green power indicator turns on when the power is turned on.
6. After a logo screen and several seconds of power-on testing, the computer loads the Windows 98 operating system.
7. As this is the first time you have used your computer, Windows begins by running the
Windows 98 Setup Wizard
.
Power button
AC adapter
1-2

Setting Up Windows 98

Windows 98 is pre-installed on your computer, including the special drivers and software used by built-in components such as the audio and video system, the modem, and the PC card slot. The Windows Setup program lets you enter personal data such as your name, the date and time in your location, and so on. It takes just a few minutes to complete. The setup process has four steps:
Getting started This section asks for your name.
Registration This section configures your mode m
Windows License This section asks you to accept the Windows License Agreement and to enter the
Windows Product Key
Final Settings This section checks the date and time in your location, and then completes the
configuration of your system
Once you start the system for the first time, be sure to comp lete the setup program. Windows does not display the Setup Wizard the next time you turn on the computer.
About Windows Properties Dialog Boxes
In this manual you are o ften asked to open a
Modem Properties
as the dialog boxes let you make changes to the configuration and operation of the component by clicking check boxes or selecting radio buttons. To open a Property dialog box, click the
Settings
Select icon to display a Properties dialog box, or similar window, for the component or feature represented by that icon. Some of the Properties dialog boxes that are used to configure components in your computer include:
Display
Control Panel
-
dialog box, or the
Start
button in the taskbar at the foot of the Windows display.
. In the Control Panel window, double-click on an
Component Properties
Display Properties
dialog box. These
dialog box, such
1
Modem
Mouse
1-3
PC Card
Power Management
1
System

Turning Off Your Computer

When you’re finished using your computer, turn it off with the following steps:
1. Click the menu.
2. In the the OK button. The power indicator turns off.
3. Close the cover to keep the screen and keyboard clean and protected.
You can shut down the computer with the power button using the steps below:
1. From the
Power Management
2. In the
3. Select
my computer”
Since this is your first session using the computer, it’s a good idea to leave the AC adapter connected to the computer until the internal battery is fully charged. The orange battery charge indicator changes to green when the battery is fully charged.
Start
button in the taskbar and click on
Shut Down Windows
Start
menu, select
Power Management Properties
Shutdown
in the drop down menu for
, and then click
If you have not saved a file, a dialog box appears prompting you to save the file.
Don’t turn off your computer if status indicators show that the
computer is still accessing data on the hard disk drive, the floppy disk drive or the CD-ROM drive. Data may be lost or damaged.
After turning off the computer wait at least five seconds before
turning the computer back on. Turning the computer off and on without a pause can damage the system.
dialog box, check the
Settings – Control Panel
icon.
Apply
Shut Down
Shut down
and double-click the
dialog box, click the
“When I press the power button on
and OK.
from the Start
item and then click
Advanced
tab.
1-4
CHAPTER 2

Basic Operations

This chapter describes some of the basic operations of your computer such as using the keyboard, adjusting the display, and so on.

Powering the Computer

You can operate your computer by using the AC adapter to connect to a suitable power outlet. You can also power the computer by the internal Lithium-Ion battery.
Whenever you use the AC adapter to power the computer, the internal battery automatically begins recharging. Recharging continues whether the computer is turned on or off.
Refer to charging and related information.
Chapter 3 Battery and Power Management
for a full description of battery
2
2-1
Power and Battery Indicators
For proper operations it is important to understand the operation of the power and battery indicators located beside the right-side hinge of the upper cover.
2
Indicator Meanings
Green Power Indicator Icon Lamp State Status
Turned on Computer is turned on Turned off Computer is turned off
Slow blinking
Tri-color (green/red/orange) Battery Indicator Icon Lamp State Status
Turned on orange Battery is charging Turned on green Battery is fully charged Turned on red Battery low warning Flashing red Critical battery warning
Flashing orange
Computer is in Standby mode
Abnormal condition – for example the battery may be installed incorrectly
2-2

Resetting the System

You may need to reset the system after adding hardware or software so that your computer recognizes newly installed devices or software. When the message appears after the installation, click You can also restart Windows 98 from the
Restart
.
Warm Boot (Software Reset)
If the system is locked up because of a software problem, you can reset or reboot the system by pressing the keys again to restart the computer.
Resetting may cause data loss. Use the software reset o nly if the normal Windows 98 Shut Down does not work because of software malfunction. Although resetting does not damage the system, you may lose the data you are processing.
Power Switch
You can turn off the computer with the power switch if the system has hardware or software problems so that you can’t use the Windows software reset. In this case, you need to hold the power button down for more than four seconds.
Reset Switch
If all other methods fail, you can reset the computer by pressing the hardware reset switch. The hardware reset switch is in a recessed location on the base of the computer. Activate the switch with a straightened paper clip or similar implement.
OK, Yes,
Ctrl+Alt+Del
etc., to restart Windows 98.
Start
menu. Select
keys simultaneously. Press the
Shut Down
Shut Down
, then
Ctrl+Alt+Del
command or the
2
Reset switch (recessed)
2-3
_

Using the Keyboard

The built-in keyboard includes all the functions that you find on a full-sized
2
keyboard. In addition, the keyboard has built-in hot keys that you can use to control some of the functions of the computer.
The illustration below shows the location of some important keys on your keyboard.
F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
Esc
#
@
!
~ `
Caps Lock
1
Tab
Shift
Fn
Ctrl
3
2
E
W
Q
A
SJ
D
Z
X
Alt
FN Key
Windows Key
Function Keys
On their own, the operation of the function keys is usually determined by the software appli cation that you are running. In combination with the Fn key they create hot-keys that you can use to control some of the computer functions. Icons embossed on the func tion key keycaps indica te the hot-key function.
Embedded Keypad
The numeric keypad is embedded in some of the right-side alphanumeric keys. The keypad functions are embossed in the upper right corner of the keypad keycaps. You activate the embedded numeric keypad by pressing the
Fn+Insert
). Repeat the keystroke to turn off the embedded keypad.
Function Keys
$ 4
R
F
Pause Break
P -
: + ;-
+
-
= { [
"
' ? / /
Fn
^
%
6
5
T
Y
G
VC
B
*
8
7
&
8
7
I
U
4
H
1
M
0
N
*
9
0
9
O
6
5
K
2
L
3
> .
<
.
,
Alt
)
(
Delete
Insert
ScrLk
NumLk
Backspace
}
| \
]
Enter
Pg Up
Shift
Home
Pg Dn
End
FN Key
Keypad Area
Windows Keys
Num Lk
key (press
2-4
Loading...
+ 75 hidden pages