Sharp PC-9300 User Manual
How to Use this Manual
This manual describes your new notebook and contains all the information you
need to set up and use the notebook. Whether you are a new or an experienced
user, you will benefit more from this manual if you are familiar with its
organization. This manual describes the PC-9300T and PC-9300D notebooks.
Unless otherwise specified, the descriptions in this manual apply to both models.
Illustrations are based on the PC-9300T notebook.
The manual is divided into five chapters, plus appendixes.
Chapter 1 Introducing the System gives a general introduction to the notebook,
explaining the main functions such as the keyboard, the indicator lamps, etc.
Chapter 2 Using the Notebook for the First Time gives the basic steps for
getting your notebook up and running.
Chapter 3 Setup Utility shows how you can make changes to the operation and
power management of the notebook by using the Setup utility.
Chapter 4 Using the Notebook describes how to carry out typical operations on
the notebook such as using the disk drives, using the GlidePoint, changing the
display, and so on.
Chapter 5 System Expansion describes how you can use the notebook’s built-in
ports and connectors to add peripheral components to your system.
Appendixes provide advice on the routine care and maintenance of the notebook,
a guide to troubleshooting problems that may arise in the use of the notebook, and
detailed specifications on your notebook and the built-in ports. For your
convenience, an index is provided at the end of this manual.
In addition to this manual, you may want to consult the Windows 95 manual, and the
manuals for your software applications. The Sharp Online Manual, accessible from
the Windows 95 Start Menu, will also help your computing.
i
Manual Conventions
This manual uses different text styles to help identify different operations and
functions of your notebook.
Keyboard Keys
When referring to specific keys on the keyboard, the key label appears in boldface
as shown below:
Press Enter to execute the installation.
When referring to a combination of keys that are pressed simultaneously, the key
labels are separated by a plus sign (+) as shown below:
Pressing Ctrl + Alt + Del lets you reset your notebook.
Sample Entries/Prompts/Screens
This manual contains sample screens that might appear during the operation of
your notebook, including prompts (text generated by the system) and entries (text
you type on the keyboard). These are printed in a typeface like the one below:
Re-enter your password for verification.
In the following case, press the Enter key after you type the command.
C:\>FORMAT A: Enter
The screens reproduced in this manual may differ slightly from the screens you
see on your notebook.
File Names
References to commands, utilities, device drivers, directory and file names in this
manual are printed in upper case.
The CONFIG.SYS file contains the specifications for configuring the
system.
ii
Section Titles/Possible Parameters
In a section of text, words which represent selectable parameters, or words which
refer to other sections in the manual are italicized.
Select Disabled to disable the floppy disk drive. See the section Making
Changes in the Main Page for more details.
Notes and Cautions
Icons and italic text are used for notes and cautions, to make important
information stand out.
Notes: Notes give you helpful hints or suggestions on ways of performing
certain operations.
Cautions: Cautions alert you that damage to equipment or loss of data
may occur if certain procedures are not follo wed carefully.
iii
Recording Information
For future reference, please record the following information in the spaces
provided below.
Model Number:
Serial Number:
BIOS Version
Number:
Date of purchase:
Dealer’s Name:
Place of purchase:
Password:
The serial number is printed on a sticker located on the bottom of the notebook.
You will see the BIOS Version number on the LCD screen when you turn on the
notebook.
iv
Unpacking the Notebook
Please check that all the accessories listed below have been included with your
computer.
Main Unit AC Adapter Power Cord Modem Cable (US
& Canada only)
(PC-9300T only)
•
Windows 95 Manual Pack (CD-ROM and Manual)
•
Backup CD-ROM
•
CD-ROM Setup Boot Disk
•
Operatio n Manual
•
Re-installation Instructions
•
TranXit Quick Reference Guide
•
Sharp Import/Export User’s Guide
•
SuperVoice Manual (US & Canada only) (PC-9300T only)
•
AT Command Reference Manual (US & Canada only) (PC-9300T only)
In addition, your notebook package includes various software license agreements,
warranty cards, and so on. If any of the listed accessories are missing, or if the
main unit or accessories are damaged, please consult your dealer (or in case of
US, a Sharp Customer Service Center at 1-800-BE-SHARP).
Note: Only the PC-9300T is equipped with a fax/modem. The fax/modem
is available only in the USA and Canada.
v
About the System Documentation
The manuals included with your notebook are used as follows:
Operation Manual (this manual)
This manual gives instruc tions on how to operate your computer suc cessfully. It
also explains how you can use some of the software that is pre-installed on the
hard disk drive, and how you can add extra devices to your notebook, either
internally or externally.
Re-installation Instructions
This manual explains how to re-install the Windows 95 operating system and the
utility programs that are pre-installed on your notebook's hard disk drive.
Windows 95 Manual & License
This manual explains the basic procedures for using Windows 95.
TranXit Quick Reference Guide
This guide is an introduction to the TranXit infrared communications program
and basic instructions.
Sharp Import/Export User's Guide
This guide is an introduction to the Import/Export infrared communications
program.
SuperVoice Manual (US & Canada only) (PC-9300T only)
This manual expla ins how to use the fax/modem software.
AT Command Reference Manual (US & Canada only) (PC-9300T only)
This manual explains the AT command set, S-registers and result codes of the
built-in fax/modem.
Note: All the programs supplied with this notebook have already been
installed on the hard disk, so please disregard all installation instructions
mentioned in the manuals. If you need to reinstall the software, please
refer to the Re-installation Instructions and to each software manual.
vi
Table of Contents
Preface
How to Use this Manual.........................................................................................i
Manual Conventions.............................................................................................ii
Recording Information......................................................................................... iv
Unpacking the Notebook....................................................................................... v
About System Documentation..............................................................................vi
Chapter 1: Introducing the System
Introduction .......................................................................................................1-1
A Brief Tour of the System.................................................................................1-3
Opening the Unit ........................................................................................... .. 1-3
Inside the Main Unit ..........................................................................................1-4
Right-side Components......................................................................................1-7
Left-side Components.........................................................................................1-7
Rear-Edge Ports.................................................................................................1-9
Components in the Unit Base...........................................................................1-10
Chapter 2: Using the Notebook for the First Time
Connecting the AC Adapter...............................................................................2-1
System Start-up and Shut-down.........................................................................2-2
Personal Windows Installation...................................................................... .. 2-2
System Shut Down......................................................................................... .. 2-3
Using The Keyboard..........................................................................................2-4
About the Keyboard....................................................................................... .. 2-4
Key Legends.................................................................................................. .. 2-5
Special Key Combinations............................................................................. .. 2-5
Special Windows 95 Keys............................................................................. .. 2-7
Chapter 3: Setup Utility
About the Setup Utility.......................................................................................3-1
Starting the Setup Utility............................................................................... .. 3-1
Using the Setup Utility.................................................................................. .. 3-2
Leaving the Setup Utility............................................................................... ..3-2
Making Changes to the Main Page....................................................................3-4
Making Changes to the Advanced Page ............................................................3-6
Making Changes to the Security Page...............................................................3-8
About Passwords..............................................................................................3-10
Setting and Changing the Password............................................................... 3-11
a
Making Changes to the Power Page...............................................................3-12
System Power Management.............................................................................3-13
Windows Power Management....................................................................... 3-14
User-selectable Power Management.............................................................. 3-14
Making Changes to the Boot Page.................................................................. 3-17
Chapter 4: Using the Notebook
Power Supply.....................................................................................................4-1
Using the AC Adapter.................................................................................... .. 4-1
Using the Battery Pack................................................................................... .. 4-2
Battery Low Indications................................................................................. ..4-2
Initializing the Battery................................................................................... ..4-3
Battery Condition........................................................................................... .. 4-4
Storing and Retrieving Data..............................................................................4-4
Using the Fax/modem (US & Canada only)(PC-9300T only)...........................4-7
GlidePoint .........................................................................................................4-8
PC Card Slots..................................................................................................4-10
Inserting and Removing PC Cards................................................................. 4-11
Installing PC Card Drivers............................................................................. 4-12
Setting the COM Port.................................................................................... 4-13
Infrared Communications................................................................................4-14
Positioning and Preparing the Notebook and the Target Device ................... 4-14
Chapter 5: System Expansion
Installation Safety Precautions..........................................................................5-1
Installing a Memory Module............................................................................. 5-2
Changing the Battery.........................................................................................5-3
Using the Parallel Port .....................................................................................5-4
Using the External Monitor Port.......................................................................5-5
Switching the Video Display......................................................................... .. 5-5
Resolution and Number of Colors Displayed................................................ .. 5-7
Using the Serial Port.........................................................................................5-8
Using the PS/2 Port...........................................................................................5-8
Using the Video Out Jack..................................................................................5-9
Using the Audio Ports .....................................................................................5-11
Using the Game/MIDI Port............................................................................. 5-11
Appendixes
Appendix A: System Maintenance..................................................................... A-1
Taking the Notebook on the Road................................................................. ..A-1
Cleaning the Notebook.................................................................................. ..A-2
Appendix B: Notes on Software ........................................................................B-1
About the Suspend-to-disk Partition.............................................................. ..B-1
Memory Management Software..................................................................... ..B-4
Appendix C: Troubleshooting...........................................................................C-1
Appendix D: System Mapping...........................................................................D-1
Memory Map................................................................................................. . D-1
DMA Channels.............................................................................................. . D-1
System Interrupts ........................................................................................... . D-2
I/O Address Map............................................................................................ . D-3
Appendix E: Connector Pin Assignments .........................................................D-1
Printer (Parallel) Port..................................................................................... ..E-1
PS/2 Port........................................................................................................ ..E-1
Serial (RS-232C) Port.................................................................................... ..E-2
External Monitor (SVGA) Port...................................................................... ..E-2
Joystick/MIDI Port........................................................................................ ..E-2
Appendix F: Specifications...............................................................................F-1
Main Unit....................................................................................................... .. F-1
Memory Modules........................................................................................... ..F-2
Spare Battery Pack: CE-M50EB.................................................................... .. F-2
c
CHAPTER 1
Introducing the System
This compact-size notebook computer is packed with a full range of multimedia
and communications features found on a full-size desktop computer. This chapter
gives general information on the system components and functions.
Introduction
This lightweight compact-size notebook computer has the following features.
•
150 MHz Pentium processor with internal cache memory, and 256K of level 2
cache memory.
•
16 MB EDO memory (upgradable to a maximum of 48 MB).
•
Built-in hard disk drive and 1.44 MB floppy disk drive.
•
Color display using either a dual scan 12.1" diagonal screen or an active
matrix 11.3" diagonal screen. Screen sizes are measured diagonally.
•
Built-in 10X CD-ROM drive (average speed).
1-1
•
Built-in 33.6 Kbps fax/modem with software support for voice mail,
speakerphone, and telephone answering (US & Canada only) (PC-9300T only).
•
Two Type-II or one Type-III compatible PC card slots, with Zoomed-Video
support on the lower slot.
•
Removable Nickel-Metal Hydride battery pack.
•
A 64-bit display controller, which operates over a high-speed PCI bus and
includes a video accelerator and 2 MB of video memory. Display output is
Super VGA 800 x 600 dots.
•
Fast infrared communication, and I/O (input/output) ports for serial and
parallel devices, external PS/2 keyboard or mouse, a joystick or a MIDI
device, analog monitor and video-out (NTSC/PAL).
•
Latest graphical user interface, and an easy-to-use GlidePoint touchpad.
•
16-bit stereo sound system compatible with the Sound Blaster Pro and
Windows Sound System standards. Built-in microphone, speakers, and jacks
for external microphone and stereo line in and out.
•
Automatic power down of peripheral devices and system components, to save
battery power, controlled by an advanced power management function.
•
Security feature which allows password protection on start-up and restricts
access to the floppy disk drive.
•
Pre-installed Windows 95 and applications software.
1-2
A Brief Tour of the System
In this section, you will learn how to locate and use the primary components of
the notebook.
Opening the Unit
Open the display as follows.
1. The screen locking latch is located in the center of the front edge of the
notebook. Slide the latch to the right and then raise the screen cover.
2. Set the display to the best viewing angle.
Screen
1-3
Inside the Main Unit
Power Indica tors
Activity Indicators
Stereo Speakers
Keyboard
GlidePoint
Color Display
Power
Switch
Microphone
Color Display
The PC-9300T uses an active matrix color display which has a diagonal length of
11.3".
The PC-9300D uses a dual scan color display which has a diagonal length of
12.1".
Power Sw itch
This switch turns on the power to the system. To turn the power on, press this
switch. When the notebook has been suspended to disk, the power switch is used
to resume it.
1-4
Keyboard
The keyboard has 87 keys (US English) or 88 keys (others). Many functions of
the notebook can be controlled by pressing special key combinations (hot keys).
Stereo Speakers
The speakers will output the sound that your notebook's software generates, or the
sound that you input through the sound ports.
Caution:
top of the speakers. The magnet inside the speakers may damage the data
on the disk.
Avoid placing floppy disks, or other magnetic storage media on
GlidePoint
The GlidePoint is located just in front of the keyboard. The left and right selection
buttons are placed just in front of the GlidePoint surface. The GlidePoint
functions just like a mouse or trackball.
Power Indicators
The three power indicator lamps are located between the hinges of the screen
cover. Fro m left to right, the power indicators have the following functions.
AC Power
Battery Power
When the notebook is operating using power supplied
through the AC adap ter, this indica t or turns on with a green
color when the notebook is on, or blinks when the notebook
is in the suspend to RAM mode.
When the notebook is operating using power supplied
through the internal battery, this indicator turns on with a
green color when the notebook is on, or blinks when the
notebook is in the suspend to RAM mode.
Battery Charge
This indicator shows the status of the battery. When the
battery is charging it turns on with an amber color. When the
battery is fully charged, it changes to green. When the
battery is low on charge, it flashes with a red color.
1-5
Activity Indicators
The six activity indicators are located just above the center of the keyboard. The
lamps turn on when the function that they represent is active. From left to right,
the activity indicators have the following functions.
CD-ROM
Hard Disk Drive
Floppy Disk Drive
Num Lock
Caps Lock
Scroll Lock
This indicator turns on whenever the system is reading from
a disc in the CD-ROM drive.
This indicator turns on whenever the system is reading from,
or writing to the hard disk drive.
This indicator turns on whenever the system is reading from,
or writing to a diskette in the floppy disk drive.
This indicator turns on when the keyboard is in Num Lock
mode. In this mode, the numeric keypad embedded in the
keyboard becomes active.
This indicator turns on when the keyboard is in Caps Lock
mode. In this mode, all typed text uses capital letters.
This indicator turns on when the keyboard is in Scroll Lock
mode. In this mode, text will scroll onscreen without
changing the position of the cursor.
Microphone
The microphone is located near the front right edge of the notebook. The
microphone can be used to record sounds, or it can act as a telephone mouthpiece
when you are using the built-in fax/modem as a speakerphone (US and Canada
only) (PC-9300T only).
1-6
Right-side Components
Infrared PortCD-ROM Drive
CD-ROM Drive
The CD-ROM drive can be used to read from CD-ROM data discs, video discs,
and audio discs. Your notebook identifies the CD-ROM drive as drive R.
Infrared Port
The infrared port supports the ASK infrared standard, and also the IrDA infrared
standard. Your notebook identifies the infrared port as COM2.
Left-side Components
Security
Cable Anchor
Audio Ports
PC Card Slots
Telephone
(RJ11) Socket
Floppy Disk
Eject Button
Floppy Disk
Drive
Security Cable Anchor
This recta ngular hole can be used as an anchor point for a computer security
cable. You can use this cable to lock your notebook to a desk or some other
secure location, and so prevent theft.
PC Card Slots
1-7
There are two Type-II PC card slots. You can also use a Type-III PC card in the
lower slot. The lower slot has an integrated Zoomed Video port so that you can
use PC cards that support the Zoomed Video standard (ZV cards) in the lower
slot. Eject buttons for both slots are placed at the right side of the slots. The
buttons are folded down when not in use. Your notebook identifies the PC card
slots as drives D and E, when you are using PC cards that store data.
Audio Ports
The three audio ports are located below the PC card slots. From left to right the
audio ports are:
Audio Input Jack You can use this jack to input stereo sound from other devices,
such as a radio or a tape recorder, into your notebook.
External
Microphone Jack
Audio Output
Jack
You can use this jack to input the sound from an external
microphone into your notebook. When an external microphone
is connected to this jack, the built-in microphone is
automatically disabled.
You can use this jack to output the sounds generated by your
notebook to an external device such as stereo loudspeakers or
headphones. When an external device is connected, the built-in
speakers are automatically disabled.
Telephone (RJ11) Socket (US and Canada only) (PC-9300T only)
The telephone socket is used to connect the internal fax/modem to a telephone
cable that terminates in an RJ11 connector.
Floppy Disk Drive
The floppy disk drive can be used to read and write to 3.5" floppy disks with
capacities of 720K or 1.44 MB. Your notebook identifies the floppy disk drive as
drive A.
Hard Disk Drive
The hard disk drive is an internal component. It operates using an Enhanced IDE
(Integrated Drive Electronics) interface. Your notebook identifies the hard disk
drive as drive C.
1-8
Rear-Edge Ports
J
P
Expansion
Connector
External
Monitor
Video Out Jack
ort
AC Adapter
ack
The rear-edge of the notebook has two connector compartments and an AC
adapter jack. You can access the connector compartments by pulling the
compartment covers open.
RS-232C
Serial Port
PS/2 Por t
Printer Port
Game /
MIDI
Port
Expansion Connector
The expansion connector is in a separate compartment. The expansion connector
is used to connect your notebook to an optional port replicator (CE-M50PR). For
information on the port replicator, see the manual supplied with the CE-M50PR
port replicator.
AC Adapter Jack
You can plug the cable from the AC adapter into the AC adapter jack in order to
power your notebook from the AC adapter.
External Monitor Port
You can use the external monitor port to connect your notebook to an external
monitor that supports Super VGA and extended SVGA resolutions.
RS-232C Serial Port
You can use this port to connect your notebook to a serial device such as a serial
printer or a serial mouse. Your notebook identifies this port as COM1.
Video Out Jack
Use the video out jack to connect your notebook to a PAL or NTSC format TV
receiver.
1-9
PS/2 Port
Use this port to connect your notebook to a PS/2 device such as an external
keyboard or an external pointing device.
Printer (Parallel) Port
Use this port to establish parallel communications with another device such as a
printer. Your notebook identifies the printer port as LPT1.
Game/MIDI Port
You can use this port to connect the notebook to a joystick or a MIDI device.
Components in the Unit Base
Battery Pack
Floppy Disk
Drive
Memory
Compartment
Battery Pack
The battery pack is removable. To remove the battery, slide the two latches open
and then remove the battery from the compartment.
Memory Compartment
The memory compartment can be used to install an optional memory module (CEA311B, CE-A312B, or CE-A323B) in order to add extra memory to your
notebook.
Floppy Disk Drive
The floppy disk drive can be easily removed for service. We recommend not to
remove the floppy disk drive module under normal operation.
1-10
CHAPTER 2
Using the Notebook for the
First Time
This chapter explains the procedures that you should follow the first time that you
use the notebook.
Connecting the AC Adapter
Your notebook can be powered by the internal, removable, rechargeable battery
pack, or it can be connected to a wall power outlet using the supplied AC adapter.
More information on the notebook's power requirements can be found in the topic
Power Supply in Chapter 4.
Note: Use the AC adapter to connect your computer to a power source
before turning on your notebook for the first time.
To start using your notebook, follow the steps below:
1. Make sure the notebook is turned off.
2. Connect the cable from the AC adapter to the AC adapter jack.
3. Connect the power cord to the AC adapter.
Caution: Only use the approved AC adapter (EA-905V) that is supplied
with the system. Do not use any other adapter than the one supplied with
the system. The AC adapter can be connected to a power outlet using a
voltage level of from AC 100 - 250 volts. The voltage rating of the power
cord is, however, variable from country to country. Please consult your
vendor for more information.
4. Insert the AC power cord plug into a wall outlet.
To Wall
Outlet
AC Adapter
2-1
System Start-up and Shut-down
1. After you have connected the AC adapter, open up the screen cover by
sliding the screen locking latch to the right.
2. Press the power switch to turn on the notebook.
Note: If you see the following message at the boot time, press F2, then
Enter to run the Setup utility with the d e fault values.
System battery is dead - Replace and run SETUP
Real time clock error
Mouse initialized
Press <F1> to resume, <F2> to Setup
In the Setup utility, set time, date and other fields appropriately. Then
press Esc, then Enter to save the values and restart the notebook. For
information on the Setup utility, see Chapter 3.
3. Your notebook will execute a brief Power On Self Test. This test initializes
all the major components of the system and verifies that they are operating
correctly. The notebook will then load the Windows 95 operating system.
Note: If you press the F8 key while your notebook displays the message
“Starting Windows 95....”, you can select an alternate start-up than
Windows 95. See the Windows online help for more information.
4. After the notebook has loaded Windows, you can click on the Start menu to
begin computing in the Windows environment.
Note: Access to Electronic Services like America Online and
CompuServe, as offered by this version of Windows 95, may not be
available in all countries of purchase of this notebook.
Personal Windows Installation
Windows 95 has been partially installed on your notebook. The first time you use
your notebook, Windows will automatically complete the installation by asking
for personal details such as your name, your time zone and so on. Follow the
onscreen prompts to complete the Windows installation.
2-2
Note: Some machines may show a Safe Recovery message when they are
turned on. This message is created because the notebook has been turned
on and then off again without the Windows 95 final installation. For
example, the system vendor may have turned the notebook on and off in
order to verify that it was operating correctly. You can ignore the Safe
Recovery message and continue with the Windows installation.
Setting the SHARP Original Wallpaper
After setting up Windows 95, set the SHARP original wallpaper in the following
procedure.
1. Double-click the “Click me to set up SHARP Wallpaper” icon on the
Windows desktop.
2. When the message appears, click OK. The SHARP original wallpaper is
displayed on the screen as a default.
System Shut Down
1. Press the Alt + F4 keys, or click on Shut Down from the Start menu.
2. In the Shut Down Windows dialog box, select which method of shut down
you prefer, and then press the Enter key or click on the Yes button.
3. Your notebook will automatically shut down.
Note: Do not turn the power off or reboot while the system is accessing
any of the disk drives. This may result in damage to the drive or disk, or
loss of data. After the notebook is turned off, wait at least five seconds
before turning the notebook back on. Turning the power on and off too
quickly can damage the notebook.
When the notebook is turned off, we recommend that you keep the screen cover
closed to protect the screen from dust and/or damage.
2-3
Using The Keyboard
F
N
Fn (
y
The built-in keyboard has 87 keys (US English) or 88 keys (Others).
About the Keyboard
The layout of your notebook's keyboard is similar to a normal keyboard. In
addition, there are twelve function keys, cursor control keys, and other special
function keys such as Ctrl, Alt, Esc, Prt Sc, Pause, Pg Up, Pg Dn, Home and
End.
unction Keys
Function) Ke
The Numeric Keypad is embedded in the right-of-center alphanumeric keys. The
keypad is activated and deactivated by pressing the Num Lock key. The Num
Lock indicator turns on when in Num Lock mode.
Alphanumeric Keys
umeric Keypad
Cursor Arrow Keys
2-4
Key Legends
The keycaps are engraved with different legends to indicate the function of the
key.
Large Light-Gray Legends
These represent the standard function of the key.
Small Blue Legends
These represent the function of the key if the Num Lock key has been pressed
and the keyboard is in Num Lock mode.
Function Key Icons
These represent special functions that are embedded into the Function Keys of the
keyboard. They are activated by holding down the Fn Function key and then
pressing the appropriate key.
Special Key Combinations
Special key combinations allow you to use various functions of the notebook
easily.
With the Ctrl and Alt Keys
Ctrl + Alt + Del
Pressing the Ctrl + Alt + Del key combination halts all operation of your
notebook and displays the message on the screen. Pressing this key combination
again will restart the notebook. This is known as a “warm boot”. This key
combination may be useful if you e ncounter hardware or software pro blems which
“lock up” your notebook.
Caution: The use of the Ctrl + Alt + Del key combination will result in
the loss of all data in memory.
With the Fn Key
The Fn key, in combination with other special keys, controls some of the
notebook's features. Symbols are printed on the keyboard to show the functions.
2-5
Fn + F3
This key combination decreases the volume of the audio
system. Hold down the keys until the volume is correct.
Fn + F4
This key combination increases the volume of the audio
system. Hold down the keys until the volume is correct.
Fn + F5
Each press of this key combination changes the video output
of the notebook. The operation of this key combination
changes depending on which display devices are connected
to your notebook on start-up. See the table below:
Ext. Monitor (LCD
+ CRT)
Start-up Display
First Press
Second Press
Third Press
Fourth Press
(Return to First)
* This display only occurs i f you have
Setup utility.
Note 1:
If the field
Enabled
, the display on the external monitor will change to the resolution of a TV display.
LCD + CRT LCD LCD + CRT
LCD No Display LCD
CRT *TV CRT
Note 1
CRT
LCD + CRT LCD LCD + CRT
Display to TV
Disabled
is
Note: When using both the LCD and an external monitor at the same
time, the external monitor should have the capability to display 800 x 600
resolution. Some external monitors which support only 640 x 480
resolution do not work properly.
TV Receiver
(LCD + TV)
LCD TV (& CRT)
Enabled
the field
, this key press is omitted. If the field
Ext. Monitor & TV Receiver
(LCD + CRT + TV)
Display to TV
Note 1
in the Advanced page of the
Display to TV
is
Fn + F6
Fn + F7
2-6
This key combination darkens the built-in screen.
This key combination brightens the built-in screen.
Fn + F8
This key combination decreases the contrast of the built-in
screen. Hold down the keys until the display is correct. This
function only operates if you have a DSTN (dual-scan)
color display.
Fn + F9
Fn + F10
Fn + F11
Fn + F12
This key combination increases the contrast of the built-in
screen. Hold down the keys until the display is correct. This
function only operates if you have a DSTN (dual-scan)
color display.
This key combination switches the Battery Low beep on
and off. Note that this combination disables the beep
temporarily but does not change the data in the Setup utility.
This key combination turns off the backlight on the built-in
screen. Press the keys again to turn the backlight back on
again.
This key combination puts your notebook into suspend
mode (either to disk or to RAM depending on the settings
of the Power page in the Setup utility).
Special Windows 95 Keys
This key can be used to open up the St art menu on the
Windows 95 Taskbar.
This key can be used as an alternative to the right mouse
button. For example, it opens a configuration menu fo r objects
on the Windows desktop.
2-7
Loading...