Sharp PC814X, PC814X1 Datasheet

Dept.,11

Opto-Electronic Devices Div.

ELECOM Group
SHARP CORPORATION

u*

T. Matsumura,
Department General Manager of

Engineering

PL“7

3.

Please contact and consult with a Sharp sales representative for any questions about this product.

CUSTOMER’S APPROVAL

DATE

BY

DATE
PRESENTED
BY

(4)

Please contact and consult with a Sharp sales representative if there are any questions

regarding interpretation of the above three paragraphs.

-

Medical equipment

1

*

Nuclear power control equipment

-

Telecommunication equipment (for trunk lines)

-

Space equipment

[

;

(3)

Please do not use this product for equipment which require extremely high reliability

and safety in function and precision, such as

-

Other safety equipment

1

*

Rescue and security equipment

*

Gas leakage sensor breakers

signals

*

Traffic

-

Transportation control and safety equipment (aircraft, train, automobile etc.)

[

;

*

Computers

1

If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions given in those respective paragraphs.

(2) Appropriate measures, such as fail-safe design and redundant design considering

the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as

-

Tooling machines

*

Measuring equipment

*

Telecommunication equipment (Terminal)

-

Home appliances

*

Audio visual equipment

*

OA equipment

[

:

(1)

This product is designed for use in the following application areas

SPECI:

I

FICATION

I

OPTO-ELECTRONIC DEVICES DIV.

DEVICE SPECIFICATION FOR

PHOTOCOUPLER

Business dealing name

MODEL No.

PC814

.

1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.

2.

When using this product, please observe the absolute maximum ratings and the Instructions for use outlined

in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.

(Precautions)

January23,

1998

PAGE

10 Pages

APPROVED BY:

DATE:

ELECTRONIC COMPONENTS
GROUP SHARP CORPORATION

REPRESENTATIVE DMSION

ISSUE

SW

.

iy$?

A,

g4fi

.q&l,Li

: /I:

PREPARED BY:

DATE:

SPEC. No.

ED-96 197XB

Ta=25%

vc,=5v

I

.

PC814Xl

A

0.5 to 1.5

1mA

I,=+

(mA1

Test

product

dealing name

conditions

PC8 14X

A or no mark

0.2 to 3.0

(“0”

mark indicates business dealing name of ordered product)

Ordered

Business

Rank mark

Ic

(Ic)

Delivery rank table

that

the isolation voltage be measured in insulation oil.1

6.2 Collector current

(21

The dielectric withstand tester with zero-cross circuit shall be used.

(31 The wave form of applied voltage shall be a sine wave.

(It is recommended

(1) Short between anode and cathode on the primary side, and between collector

and emitter on the secondary side.

CY8543K02.

3.

Ratings and characteristics

Refer to the attached sheet, page 4 to 6.

4.

Reliability

Refer to the attached sheet, page 7.

5.

Outgoing inspection

Refer to the attached sheet, page 8.

6.

Supplement

6.1

Isolation voltage shall be measured in the following method.

spectication

applies to the outline and characteristics of photocoupler

Model No. PC8 14X.

2.

Outline

Refer to the attached drawing No.

SHARP CORPORATION

1.

Application

This

PBBO,

and PBB, are not used

in this device at all.

7. Notes
Refer to the attached sheet-l-1.2.

(Methylchloroforml

6.7

Brominated flame retardants
Specific brominated flame retardants such as the

-Trichloroethane

tetracbloride,

1.1.1

Halon,

Carbon CFC,,

:

-

component.

Materials for ODS

shaI.I

not contain the following materials.
Also, the following materials shall not be used in the production process
for this device

-

component

This

photocoupler is designed for AC input..

product is not designed against irradiation.

This product is assembled with electrical input and output.

This product incorporates non-coherent light emitting diode.

6.6

ODS materials

This device

This

:

E64380

6.4

6.5

:

PC8 14X

UL file No.

Z/8

6.3

This Model is approved by UL.

Approved Model No.

PC814X

1

January 23, 1998

MODEL No. PAGE

SHRRP

CORPORATION

ED-96197XB

CY8543K02

PC814X)

Drawing
No.

:

l/l

mm

PC814

Name

Outline Dimensions
(Business dealing
name

shall be

or shall not be marked.

UNIT:

*2)

Factory identification mark

shall be marked according to DIN standard.

0.25g

* 1) 2-digit number

:

Approx.

1-k

l

Z

Pin Nos.

and internal

connection diagram

Product mass

=I-,

Rankmark

Primary side mark

SHARP CORPORATION