Sharp PC357N1T, PC357N2T, PC357N4T, PC357N5T, PC357N6T Datasheet

PREPARED By: DATE:

SPEC. No. ED-97136

SHARP

ISSUE

September 8, 1997

ch-\ ,w J&&/.-i /ti,,99c

PAGE 14 Pages

APPROVED BY: DATE: ELECTRONIC COMPONENTS

,‘$‘..

GROUP SHARP CORPORATION REPRESENTATIVE DIVISION

“: :y

i. 1

r^ i

- ,/

‘3 5 ILMZ~~

>3p ’

i

SPECIFICATION

OPTO-ELECTRONIC DEVICES DIV

f DEVICE SPECIFICATION FOR

Business dealing name

PHOTOCOUPLER

MODEL No.

1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”). Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.

2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets, and the precautions mentioned below.

(Precautions)

(1) This product is designed for use in the following application areas ;

[

l

OA equipment

l

Audio visual equipment l Home appliances

l

Telecommunication equipment (Terminal)

* Measuring equipment

l

Tooling machines

l

Computers

1

If the use of the product in the above application areas is for equipment listed in paragraphs (2) or (31, please be sure to observe the precautions given in those respective paragraphs.

(21 Appropriate measures, such as fail-safe design and redundant design considering

the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as ;

[

* Transportation control and safety equipment (aircraft, train, automobile etc.) * Traffic signals - Gas leakage sensor breakers * Rescue and security equipment

* Other safety equipment

1

(3) Please do not use this product for equipment which require extremely high reliability

and safety in function and precision, such as ;

[

* Space equipment * Telecommunication equipment (for trunk lines) * Nuclear power control equipment m Medical equipment

1

(4) Please contact and consult with a Sharp sales representative if there are any questions

regarding interpretation of the above three paragraphs _

3. Please contact and consult with a Sharp sales representative for any questions about this product. DATE

CUSTOMER’S APPROVAL

PRESENTED BY

~gj?/

T. Matsumura,

DATE

Department General Manager of Engineering Dept. ,I1 Opto-Electronic Devices Div.

BY

ELECOM Group SHARP CORPORATION

SHARP CORPORATION

1. Application This specitication applies to the outline and characteristics of photocoupler

Model No. PC357.

2. Outline Refer to the attached drawing No. CY9269KO2.

3. Ratings and characteristics Refer to the attached sheet, page 5 to 7.

4. Reliability Refer to the attached sheet, page 8.

5. Incoming inspection Refer to the attached sheet, page 9.

6. Supplement

6.1 Isolation voltage shall be measured in the following method. (1) Short between anode and cathode on the primary side and between

collector and emitter on the secondary side. (2) The dielectric withstand tester with zero-cross circuit shall be used. (3) The wave form of applied voltage shall be a sine wave.

6.2 Packaging specifications

Refer to the attached sheet, page 10 to 12.

SHARP CORPORATION

ED-97136

1 September 8, 1997

MODEL No. PAGE

PC357NT 2/ 12

6.3 Business dealing name (“0” mark indicates business dealing name of ordered product)

Rank mark

Ic blA)

Test conditions

I

PC357NIT 1 A

I

4.0 to 8.0

I

PC357N2T 1 B

I

6.5 to 13

I

PC357N3T 1 C

I

10 to20

I

1,=5mA

I

PC357N4T 1 D

I

15to30

I

PC357N5T 1 A or B

I

4.0 to 13

I

0

PC357N6T PC357N7T

PC357N8T PC357N9T PC357NOT PC357NT

B or C C or D

A, B or C

B, CorD

A, B, C or D

A, B, C, D or no mark

6.5 to 20 10to30

4.0 to 20

6.5 to 30

4.0 to 30

2.5 to 30

vc,=5v

Ta=25%

6.4 The following selection shall be made as to the collector-emitter breakdown voltage (BVceo) in parameter 3.2.

(Applied to lot No. “J5” [May 19971 or later]

Parameter Symbol Conditions MIN. TYP. MAX. unit

Collector-emitter

BVCEO

Ic=O. 1mA 70 - -

V

breakdown voltage Ir=O

6.5 This Model is approved by UL. Approved Model No. : PC357 UL iile No. : E64380

6.6 This product is not designed against irradiation. This product is assembled with electrical input and output.

This product incorporates non-coherent light emitting diode.

SHARP CORPORATION

6.7 ODS materials This device. component shall not contain the following materials.

Also, the following materials shall not be used in the production process for this device * component.

Materials for ODS :

CFC!,, Halon, Carbon tetrachloride,

1.1.1 -Trichloroethane (Methylchloroform)

6.8 Brominated flame retardants Specific brominated flame retardants such as the PBBO, and PBB, are not used

in this device component at all.

7. Notes Refer to the attached sheet- l-l, 2.

SHARP CORPORFlTl ON

ED-97136

1 September 8, 1997

MODEL No.

PAGE

PC357NT

4/

12

<

3. 6+0. 3

CD (3

k 2.54kO.254

*

Epoxy resin

Pin Nos. and

internal

connection diagram

Date code ‘1

0

Anode

0

Cathode

\ Rank mark Factory identification mark l 2

.-

22

.

z

cx d

+I

;

@

Collector

3

Emitter

I I

Product mass : Approx. 0.1 Og

*l) 2-digit number shall be marked according to DIN standard.

*2) Factory identification mark shall be or shall not be marked.

*31 Marking is laser marking

I

UNIT: l/l mm