Sharp PC123A, PC123B, PC123C, PC123S, PC123Y Datasheet

...

PREPARED BY: DATE:

)4/

,(- :-,, < ‘. h

&&-‘/,L ’

.%’ 2

APPROVED BY: DATE:

- ,.

I- 1 -. ,dC,

SPEC. No. ED-94040E

SHARP

ISSUE March 5, 1998

PAGE 14

Pages

ELECTRONIC COMPONENTS GROUP SHARP CORPORATION REPRESENTAm

DMSION

A 1 lUi\1

OPTO-ELECTRONIC DEVICES Dn!

’ DEVICE SPECIFICATION FOR

PHOTOCOUPLER

MODEL No.

PC123

business dealing name

These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”). Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.

When using this product, please observe the absolute maximum ratings and the instructions for use outlined

in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings

and the instructions included in these specification sheets, and the precautions mentioned below.

(Precautions)

ill This product is designed for use in the following application areas :

[

* OA equipment

* Audio visual equipment

* Home appliances

* Telecommunication equipment (Terminal)

* Measuring equipment

* Tooling machines

+ Computers

If the use of the product in the above application areas is for equipment listed in paragraphs (2) or (31, please be sure to observe the precautions given in those respective paragraphs.

(21 Appropriate measures, such as fail-safe design and redundant design considering

the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as ;

[

. Transportation control and safety equipment (aircraft, train, automobile etc.1

- Trafhc signals

* Gas leakage sensor breakers

. Rescue and security equipment

* Other safety equipment

(31 Please do not use this product for equipment which require extremely high reliability

and safety in function and precision, such as :

[

. Space equipment . Telecommunication equipment (for trunk lines)

* Nuclear power control equipment * Medical equipment

(41 Please contact and consult with a Sharp sales representative if there are any questions

regarding interpretation of the above three paragraphs.

. Please contact and consult with a Sharp sales representative for any questions about this product.

CUSTOMER’S APPROVAL

DATE PRESENTED BY

DATE

T. Matsumura,

Department General Manager of Engineering

Dept.,11

Opto-Electronic Devices Div. ELECOM Group

SHARP CORPORATION

PC 123

l/8

1. Application This specification applies to the outline and characteristics of photocoupler

Model No. PC123.

2. Outline Refer to the attached drawing No. CY725 lKO2.

3. Ratings and characteristics

Refer to the attached sheet, page 4 to 6.

4. Reliability Refer to the attached sheet, page 7.

5. Incoming inspection Refer to the attached sheet, page 8.

6. Supplement

6.1 Isolation voltage shaIl be measured in the following method. (1 I Short between anode to cathode on the primary side and between collector

to emitter on the secondary side.

(2) The dielectric withstand tester with zero-cross circuit shall be used. (3) The wave form of applied voltage shall be a sine wave.

(It is recommended that the isolation voltage be measured in insulation oil.1

6.2 Collector current (Ic) Delivery rank table (”

0”

mark indicates business dealing name of ordered product)

Rank at Business Rank at

* Business

delivery dealing name delivery dealing name

Rank mark Ic (mAI

Test

conditions PC123 PC123A

PC123B

PC123C

PC123Y A, B, S or no mark 2.5 to 20

1,=5mA

PC123Yl A

2.5 to 7.5 vc,=5v

PC 123Y2 B

5.0 to 12.5 . Ta=25”C

PC123Y5 no mark

10.0 to 20.0

PC123S PC 123YS S

5.0 to 10.0

* Applied to products as an option (Attach sheet 2-l to 2-4)

ED-94040E

MODEL No.

1 March 5, 1998

1 PAGE

SHARP CORPORATION

ED-94040E

1 March 5, 1998

MODEL No.

PAGE

PC 123

2/8

6.3 This Model is approved by UL. Approved Model No. : PC123 UL tile No. : E64380

6.4 This Model is approved by CSA. Approved Model No. : PC123 CSA file No. : CA95323 CSA approved mark ”

sp: shall be indicated on minimame unit package.

6.5 This product is approved by BSI. (BS415, BS7002) Approved Model No. : PC123 Certificate No. : 7087/7409

6.6 This product is approved by SEMKO, DEMKO, NEMKO and EI.

6.7 This product is not designed against irradiation. This product is assembled with electrical input and output. This product incorporates non-coherent light emitting diode.

6.8 ODS materials This product shall not contain the following materials.

Also, the following materials shall not be used in the production process for this product. Materials for ODS :

CFC,, Halon, Carbon tetrachloride,

1.1.1 -Trichloroethane (Methylchloroform)

6.9 Brominated flame retardants Specific brominated flame retardants such as the PBBO, and PBB, are not used

in this device at all.

Notes Refer to the attached sheet- 1 - 1, 2.

SHARP CORPORflTI ON

PC 123

3/B

2. Outline

Rank mark

mark l 2

7.62’0-3

1: Anode

2: Cathode

Emitter

Collector

*l) a-digit number sha.lI be marked according to DIN standard. *2) Factory identification mark shall be or shall not be marked. *3) Marking is laser marking

Pin Nos. and

internal

connection diagram

4. 58

‘0.3

ED-94040E

MODEL No.

1 March 5, 1998

1 PAGE

Product ‘mass : Approx. 0. 18g

UNIT:l/lmm

SHARP CORPORflTION

PC 123

3. Ratings and characteristics

3.1 Absolute maximum ratings Ta=25”C

*l The derating factors of absolute maximum ratings due to ambient temperature

are shown in Fig. 1 to 4. *2 Pulse widths100 pus, Duty ratio : 0.001 (Refer to Fig. 5) *3 AC for 1 min. 40 to 6O%RH *4 For 10s

*2 Peak forward current

+ 10 hidden pages