Sharp NOTEVISION XG-NV6XU User Manual
Quick Reference for XG-NV6X
LCD Projector
A. Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the
projector .
B. Connecting a Computer
1 Slide the 15 pin/BNC switch on the rear terminals to the 15 pin
position.
2 Plug one end of the supplied computer cable into the INPUT 1
or 2 port on the projector and the other end into the monitor
output port on the computer, and secur e the plugs by tightening
the thumb screws.
3 Plug one end of the supplied computer audio cable into AUDIO
INPUT 1 or 2 terminal on the projector and the other end into
the audio output port on the computer.
C. Connecting the Remote Mouse Receiver
IBM or IBM compatible PC
1 Connect one end of the supplied mouse control cable to the
corresponding terminal on the PC.
2 Connect the other end to the remote mouse receiver.
Macintosh
1 Connect the mouse control serial cable to the remote mouse
receiver.
2 Connect the mouse control cable for Mac to the Mac ADB
port on the Mac.
3 Connect the other end of the mouse control cable for Mac to
the mouse control serial cable.
• Make sure that your computer is turned off while making any mouse control cable
connections.
• When using the wireless mouse with an IBM or IBM compatible PC, you can use
either a PS/2 or serial cable connection. (See diagram below.)
• Use the supplied mouse control cable for Mac when using the remote mouse receiver
with a Macintosh computer.
Remote mouse receiver
Mouse control cable for IBM PS/2
Mouse control
cable for Mac
Use this terminal to connect the
supplied mouse control cable
to the remote mouse receiver.
Mouse control
serial cable
4 Press POWER ON.
POWER ON
button
5 Turn on the computer.
6 Press AUTO SYNC to adjust the image.
AUTO SYNC
button
D. Connecting a DVD Player, DTV Decoder
and Other Component Video Equipment
1 Slide the 15 pin/BNC switch on the rear terminals to the BNC
position.
2 Plug the supplied BNC-RCA adaptors to INPUT 1 terminals
3 Connect a component cable and an audio cable to the
Three BNC-RCA adaptors
While this projector can input COMPUTER/RGB and
COMPONENT signals through the 15-pin D-sub terminals (INPUT
1 and 2 ports) and BNC terminals (INPUT 1 terminals), the
projector cannot distinguish between the two types of signals.
When inputting these signals through the aforementioned
terminals, you must indicate the input signal type. (See “Selecting
the Signal Type” in the operation manual.)
R), G/G sync(Y), B(PB)).
(R(P
corresponding terminals on the projector and video source.
Audio cable
(sold separately)
To analog component
output terminals
To audio output terminal
Component cable
(sold separately)
DTV decoder
or
DVD player
XG-NV6XU/QR (E) 99.11.8, 2:05 PM1
E. Connecting a VCR, Laser Disc Pla yer and
Other Audiovisual Equipment
1 Connect the yellow (Video) RCA connector to the corresponding
yellow terminals on the projector and video source.
2 Connect the red and white (Audio) RCA connectors to the
corresponding red and white terminals on the projector and
video source.
Audio cable
(sold separately)
To audio output terminals
g
g
g
VCR
or
Laser disc player
Video cable (sold separately)
S-video cable (sold separately)
Use this terminal when the
audio-visual equipment to be
connected has an S-VIDEO
output terminal.
To video output terminal
To S-video output terminal
F. Selecting and Checking the Input Mode
1 Press INPUT to select the desired input mode.
INPUT button
2 Press INPUT again to change the mode.
EXAMPLE
INPUT 1 Mode
INPUT 2 Mode
VIDEO Mode
g
2 Press ENTER to display test pattern.
3 Press ∂/ƒ/ß/© to make adjustments.
4a.Press LENS until normal screen appears.
4b.To reset the KEYSTONE setting, press UNDO.
• Straight lines and the edges of the displayed image may appear jagged, when
adjusting the KEYSTONE setting.
• Do not touch the lens when adjusting the focus or zoom.
H. Turning the Projector Power off
1 Press PO WER OFF.
Power OFF
button
G. Adjusting the Lens
1, 4a
3
2
4b
1 Press LENS to select mode. Each time LENS is pressed, the
screen changes in the following order.
PDF operation manuals in several languages are included in the CD-R OM. See “How to Access the
PDF Operation Manuals” in the operation manual of the projector for more details.
XG-NV6XU/QR (E) 99.11.8, 2:05 PM2
2 Press POWER OFF again while the message is displayed.
Printed in Japan
TINS-6738CEZZ
9P06-JWG
Loading...