LCD PROJECTOR
MODEL
XG-C58X
XG-C68X
OPERATION MANUAL
Introduction
Connections and Setup
Basic Operation
Easy to Use Functions
Appendix
IMPORTANT
• For your assistance in reporting the loss or theft of
your Projector, please record the Serial Number
located on the bottom of the projector and retain this
information.
• Before recycling the packaging, please be sure that
you have checked the contents of the carton
thoroughly against the list of “Supplied accessories”
on page 14.
Model No.:
Serial No.:
ii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or and of the same rating as
above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug proceed as follows:
• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by
the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured
black.
• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured
red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
iii
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian,
Dutch, Portuguese, Chinese (Simplified Chinese) and Korean. Carefully read through the operation instructions
before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch,
Italienisch, Niederländisch, Portugiesisch, Chinesisch (Einfaches Chinesisch) und Koreanisch. Bitte lesen Sie die
Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois,
espagnol, italien, néerlandais, portugais, chinois (chinois simplifié) et coréen. Veuillez lire attentivement ces
instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska,
italienska, holländska, portugisiska, kinesiska (förenklad kinesiska) och koreanska. Läs noga igenom
bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español,
italiano, holandés, portugués, chino (chino simplificado) y coreano. Lea cuidadosamente las instrucciones de
operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano,
olandese, portoghese, cinese (cinese semplificato) e coreano. Leggere attentamente le istruzioni per l’uso
prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans,
Nederlands, Portugees, Chinees (Vereenvoudigd Chinees) en Koreaans. Lees de handleiding zorgvuldig door
voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano,
Holandês, Português, Chinês, (Chinês Simplificado) e Coreano. Leia cuidadosamente todas as instruções de
operação antes de operar o projetor.
iv
Introduction
-1
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
Introduction
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference
at his own expense.
See bottom of actual set.
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
-2
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode.
During normal operation, when putting the projector into the standby mode always use the STANDBY button on the
projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution Concerning the Lamp Replacement
See “Replacing the Lamp” on page 85.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations. For disposal or recycling information,
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries
Alliance: www.eiae.org .
When Attaching the “QUICK GUIDE” Label
“QUICK GUIDE” Label
Attaching the “QUICK GUIDE” Label (supplied) on the
projector will help you check the setup procedure. When
you attach the “QUICK GUIDE” Label on the projector,
be sure to align the label bottom and the upper part of
the “Notevision” logo on the top cabinet of the projector
as shown in the drawing on the right.
This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 786,432
pixels (× RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen
TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen.
This will not affect the picture quality or the life expectancy of the unit.
Introduction
-3
Outstanding Features
1. Ultra High Brightness from a Compact Projector
••
••
• 310W SHP Lamp
Use 310W SHP lamp for excellent color uniformity and ultra high brightness.
••
••
• Power Save mode function enables lower noise levels, reduced power
consumption and longer lamp life.
2. Simple & Easy Operation
••
••
• Color coded terminals, automatic signal search and graphical menu sys-
tem insure easy set-up and configuration.
••
••
• Frequently used connections and controls are strategically placed for
easy access.
••
••
• Simple lens replacement
Using an easy access lens cover and a new bayonet mount configuration, the optional lens can be
easily installed.
3. Superior PC Compatibility
••
••
• Compatible with up to 200 Hz vertical refresh rate, Sync on Green and
Composite Sync signals for use with a wide variety of high-end PCs and
Workstations.
••
••
•
Using Advanced Intelligent Compression Technology, computer screens
of UXGA (1,600 # 1,200) resolution can be displayed with minimal distortion.
4. Advanced Computer & Video lntegrated Composer Technology
••
••
• Realizes vivid images using the latest image quality circuitry.
••
••
• New I/P conversion algorithm enhances the performance of the motion detect I/P
conversion.
Extensive improvements on the jagged edges or slanted
lines in moving images.
••
••
• Color Management System
Supports sRGB.
Enables individual settings of lightness, chromatic value
and hue for six target colors.
••
••
• Noise Reduction
Allows for a clear image even with noisy source signals.
••
••
• New Edge Up-Scaling
Reduces jaggies and flickering when up-scaling edges
of slanted lines, enabling sharper quality images.
5. Theft Deterrent and Security
••
••
• Anti-theft
This feature will render the projector useless if a keycode is not entered.
••
••
• Notevision Lock Down
A secure installation is achieved by tethering one of the projector’s
mounting points to the optical block. This added measure makes it extremely difficult to pull the projector off of its ceiling mount thus minimizing the chance of injury from horseplay or unauthorized removal of
the projector.
-4
Contents
Adjusting the Picture ........................................ 46
Adjusting Image Preferences ..................................46
Selecting the Signal Type ....................................... 46
Progressive Mode.................................................... 47
Adjusting Computer Images ............................ 48
Computer Image Adjustment .................................. 48
Saving Adjustment Settings..................................... 48
Selecting Adjustment Settings ................................49
Special Mode Settings ............................................49
Checking the Input Signal ....................................... 49
Auto Sync Adjustment .............................................50
Auto Sync Display Function ................................... 50
Easy to Use Functions
Selecting the Picture Display Mode ................ 52
Displaying a Still Image .................................... 54
Enlarging a Specific Portion of an Image ....... 55
Gamma Correction Function............................ 56
Displaying Dual Pictures (Pict in Pict) ............ 57
Black Screen Function ..................................... 58
Displaying the Break Timer .............................. 59
Color Management System (C. M. S.) .............. 60
Selecting the Color Reproduction Mode ................. 60
Selecting the Target Color ....................................... 60
Setting the Brightness of the Target Color ............... 61
Setting the Chromatic Value of the Target Color......61
Setting the Hue of the Target Color ........................ 61
Resetting User-Defined Color Settings................... 62
Overview of All Color Settings ................................. 62
Setting the Audio Output Type ......................... 63
Setting on/off the Internal Speaker.................. 63
Auto Search Function ....................................... 64
Video Digital Noise Reduction
(DNR) System .............................................. 65
Setting On-screen Display ............................... 65
Setting the Video System ................................. 66
Saving Projected Images.................................. 67
Capturing the Image .............................................. 67
Deleting the Captured Image ..................................67
Setting a Background Image............................ 68
Selecting a Startup Image ................................ 68
Selecting the Economy Mode .......................... 69
Setting the Power Save Mode ................................. 69
Monitor Out/RS-232C Off Function ..........................69
Auto Power Off Function ......................................... 70
Displaying the Remaining Lamp Life
(Percentage) ................................................. 70
Reversing/Inverting Projected Images ............ 71
Selecting the Fan Mode .................................... 71
Setting the Fan Mode .............................................. 71
Introduction
Outstanding Features ......................................... 3
Contents............................................................... 4
IMPORTANT SAFEGUARDS ............................... 6
How to Access the PDF Operation Manuals..... 9
Part Names ........................................................ 10
Projector (Front and Top View) ................................ 10
Projector (Rear View) .............................................. 11
Remote Control (Front View) ................................... 12
Remote Control (Top View) ..................................... 12
Using the Remote Control ................................ 13
Available Range of the Remote Control ................. 13
Inserting the Batteries ............................................. 13
Accessories ....................................................... 14
Connections and Setup
Connecting the Projector to Other Devices.... 16
Before Connecting.................................................. 16
This projector can be connected to: ....................... 16
Connecting the Power Cord ................................... 17
Connecting the Projector to a Computer ............. 17
Connecting to Video Equipment.......................... 19
Connecting to an Amplifier .................................. 21
Controlling the Projector by a Computer ............. 22
Connecting to a Monitor ...................................... 23
Using as a Wired Remote Control....................... 23
Using the Wireless Presentation Function of the
Remote Control ............................................. 24
Setup .................................................................. 25
Using the Adjustment Feet ..................................... 25
Adjusting the Lens .................................................. 26
Setting up the Screen ..............................................27
Screen Size and Projection Distance ...................... 28
Projecting a Reversed/Inverted Image ................... 32
Basic Operation
Setting with the Buttons
Image Projection ............................................... 34
Basic Procedure ......................................................34
Selecting the On-screen Display Language ........... 36
Turning the Power off .............................................. 37
Correcting Trapezoidal Distortion
(Keystone Correction) ................................. 38
Setting with the Menus
Menu Bar Items ................................................. 40
Using the Menu Screen .................................... 42
Menu Selections (Adjustments) .............................. 42
Menu Selections (Settings) ..................................... 44
Introduction
-5
Locking the Operation Buttons
on the Projector ........................................... 72
Setting up the Keylock ............................................ 72
Canceling the Keylock Setting ................................ 72
Selecting the Transmission Speed
(RS-232C) ..................................................... 73
Setting up a Password ...................................... 73
Entering the Password............................................. 73
Changing the Password ......................................... 74
If You Forget Your Password................................... 74
Setting the Anti-Theft........................................ 75
Entering the Keycode ..............................................75
Changing the Keycode ........................................... 76
Initializing the Settings ..................................... 77
Displaying the Adjustment Settings................ 78
Appendix
Maintenance ...................................................... 80
Replacing the Air Filter ..................................... 81
Maintenance Indicators .................................... 83
Regarding the Lamp ......................................... 85
Lamp ...................................................................... 85
Caution Concerning the Lamp ................................ 85
Replacing the Lamp ................................................ 85
Removing and Installing the Lamp Unit ................. 86
Resetting the Lamp Timer ....................................... 87
Connecting Pin Assignments .......................... 88
(RS-232C) Specifications and
Command Settings ...................................... 89
Wired Remote Control Terminal
Specifications .............................................. 92
Computer Compatibility Chart ......................... 93
Troubleshooting ................................................ 94
For SHARP Assistance ..................................... 96
Specifications .................................................... 97
Dimensions ........................................................ 98
Glossary ............................................................. 99
Index ................................................................. 100
-6
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near
a bath tub, wash bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage
to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer,
or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by
the manufacturer.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
10.Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product
and to protect it from overheating, and these openings
must not be blocked or covered. The openings should
never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
IMPORTANT SAFEGUARDS
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you
are not sure of the type of power supply to your home,
consult your product dealer or local power company.
For products intended to operate from battery power,
or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types
of plugs. If the plug should fail to fit into the power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with a
grounding terminal.
This plug will only fit into a grounding type power
outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point
where they exit from the product.
14. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of
fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric
shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to
assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR
FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic
rules for its installation, use and servicing.
Introduction
-7
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation.
e. If the product has been dropped or damaged in
any way.
f. When the product exhibits a distinct change in
performance, this indicates a need for service.
INTELLECTUAL PROPERTY RIGHTS
IMPORTANT
READ BEFORE USING THE PRODUCT
• You have acquired a product that includes software licensed to SHARP Corporation by Lineo, Inc. (“Lineo”).
The Software is protected by copyright laws, international copyright treaties, and other intellectual property laws and treaties. Lineo and its suppliers retain all ownership of, and intellectual property rights in
(including copyright), the Software components and all copies thereof, provided however, that certain
components of the Software are components licensed under the GNU General Public License (version
2), which Lineo supports. You may obtain a copy of the GNU General Public License at http://www.fsf.org/
copyleft/gpl.html. Lineo will provide source code for any of the components of the Software licensed
under the GNU General Public License. To obtain such source code, send email to embedixsupport@lineo.com.
• OS: Embedix (Embedded Linux) Embedix (TM) is a registered trademark of
U.S.A. LINEO, Inc.
• Microsoft®, Windows® and PowerPoint® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the United States.
• Adobe
®
Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh
®
is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
• This software is based in part on the work of the Independent JPEG Group.
• All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
19. Replacement Parts
When replacement parts are required, be sure that the
service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform safety
checks to determine that the product is in proper
operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling
only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
-8
IMPORTANT SAFEGUARDS
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if
lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service
Center for replacement.
See “Replacing the Lamp” on page 85.
Cautions concerning the setup of
the projector
■ For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens must be cleaned more often. As long as the
projector is regularly cleaned, use in these environments will not reduce the overall operation life of the
unit. Internal cleaning should only be performed by a
Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places exposed to
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in
a sunny or bright room.
When using the projector in high-altitude areas
such as mountains (at altitudes of approximately
4,900 feet (1,500 meters) or more)
■ When you use the projector in high-altitude areas with
thin air, set “Fan Mode” to “High”. Neglecting this can
affect the longevity of the optical system.
The projector may safely be tilted to a maximum
angle of 12 degrees.
■ Placement should be within ±12 degrees.
Do not subject the projector to hard impact and/
or vibration.
■ Protect the lens so as not to hit or damage the surface
of the lens.
Rest your eyes occasionally.
■
Continuously watching the screen for long hours will make
your eyes tired. Be sure to occasionally rest your eyes.
Avoid locations with high or low temperature.
■ The operating temperature for the projector is from 41°F
to 95°F (+5°C to +35°C).
■ The storage temperature for the projector is from
–4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
■ Allow at least 7.9 inches (20 cm) of space between the
exhaust vent and the nearest wall or obstruction.
■ Be sure that the intake vent and the exhaust vent are
not obstructed.
■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into the standby
mode. This does not indicate a malfunction. Remove
the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power
cord back in and turn on the projector. This will return
the projector to the normal operating condition.
Cautions regarding the transportation of the projector
■ When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra caution with the lens. Before moving the projector, be sure to unplug the power cord from
the wall outlet, and disconnect any other cables connected to it.
Other connected equipment
■
When connecting a computer or other audio-visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC
outlet and turning off the equipment to be connected.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of the plug
may vary depending on the region or country you are
using the projector in. When using the projector overseas, be sure to use the appropriate power cord for
the country you are in.
Temperature monitor function
■ If the projector starts to overheat
due to setup problems or blockage of the air vents, “ ” and
“ ” will blink in the lower left
corner of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter the
standby mode. Refer to “Maintenance Indicators” on
page 83 for details.
Info
• The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
• Do not unplug the power cord during projection or cooling fan operation. This can create damage due to the
rise in internal temperature, as the cooling fan also stops.
Introduction
-9
PDF operation manuals in several languages are included in the CD-ROM, so that you can
work with the projector, even if you do not have this manual. To utilize these manuals, you
need to install Adobe® Reader® on your computer (Windows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals for Windows® (For Mac®, skip step 2).
1 Insert the CD-ROM in the CD-ROM drive.
2 Double click the “My Computer” icon.
3 Double click the “CD-ROM” drive.
4 Double click the language (name of the folder) that you want to view.
5 Double click the “58_68_” pdf file to access the projector manuals.
Note
• If the desired PDF file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then
specify the desired file using the “File”, “Open” menu.
How to Access the PDF Operation Manuals
-10
Projector (Front and Top View)
Part Names
34
34
83
83
39
42
35
38
50
42
35
42
25
25
ON button
For turning the power on.
37
STANDBY button
For putting the projector into
the standby mode.
Power indicator
Illuminates red, when the
projector is in standby.
When the power is turned
on, this indicator will
illuminate green.
Lamp indicator
Illuminates green indicating
normal function. Replace
the lamp when the indicator
illuminates red.
Temperature warning
indicator
When the internal
temperature rises, this
indicator will illuminate red.
UNDO button
For undoing an operation
or returning to the default
settings.
ENTER button
For setting items selected
or adjusted on the menu.
13
Remote control
sensor
81
INPUT button
For switching input mode
1, 2, 3 or 4.
KEYSTONE button
For adjusting Keystone or
Digital Shift setting.
AUTO SYNC button
For automatically
adjusting images when
connected to a computer.
Adjustment buttons
(', ", \, |)
For selecting menu items.
VOLUME buttons
For adjusting the speaker
sound level.
MENU button
For displaying adjustment
and setting screens.
26
Zoom knob
26
Focus ring
80
Intake vent
HEIGHT ADJUST
button
Adjustment foot
Carrying handle
Air filter/cooling
fan (Intake vent)
(on the bottom of
the projector)
STANDBY
Numbers in refer to the main pages in this operation manual where the topic is explained.
Attaching and removing the lens cap
• Press on the two buttons of the lens cap
and attach it on the lens. Then release
the buttons to lock it in place.
• Press on the two buttons of the lens cap
and remove it from the lens.
In this operation manual, the illustration and
the screen display are simplified for explanation, and may differ slightly from actual display.
Introduction
-11
Projector (Rear View)
Using the Kensington Lock
•
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the
projector.
17
80
AC socket
Exhaust vent
25
17
17
Kensington Security
Standard connector
Adjustment Feet
INPUT 2 terminal
Terminal for
computer RGB and
component signals.
INPUT 1 terminal
Terminal for
computer RGB and
component signals.
23
OUTPUT (INPUT 1, 2)
terminal
Shared computer
RGB and component
signals output
terminal
for INPUT 1 and 2.
AUDIO OUTPUT
terminal
Shared audio
output terminal for
INPUT 1, 2, 3 and 4.
22
24
RS-232C terminal
For controlling
projector using a
computer.
21
17
AUDIO INPUT 1, 2
terminal
Shared audio input
terminal for INPUT 1
and 2.
19
INPUT 4 terminal
Terminal for
connecting video
equipment with an
S-video terminal.
19
AUDIO (L/R)
INPUT 3, 4
terminals
Shared audio input
terminals for INPUT 3
and 4.
19
INPUT 3 terminal
For connecting
video equipment.
23
WIRED REMOTE
control input
terminal
USB terminal
Terminal for
connecting a
computer using a
USB cable.
Carrying the projector
Before carrying the projector, fully
extend the carrying handle.
-12
Remote Control (Front View)
Part Names
38
KEYSTONE button
For adjusting Keystone or Digital
Shift setting.
23
WIRED R/C JACK
For controlling the projector by
connecting the remote control to the
projector.
34
ON button
For turning the power on.
42
MENU button
For displaying adjustment and
setting screens.
42
Adjustment buttons
(', ", \, |)
For selecting menu items.
42
ENTER button
For setting items selected or
adjusted on the menu.
39
UNDO button
For undoing an operation or
returning to the default settings.
55
ENLARGE (Enlarge/Reduce)
buttons
For enlarging or reducing part of
the image.
50
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
35
INPUT buttons
For switching to the respective
input modes.
56
GAMMA button
For correcting the brightness of an
image, when the images displayed
are hard to see because of the
brightness of the room. Four
gamma modes are available to
choose from.
35
VOLUME buttons
For adjusting the speaker sound
level.
13
Remote control signal transmitters
57
24
PinP button
For displaying dual pictures.
FORWARD/BACK buttons
Moves forward or backwards when
connected to a computer using a
USB cable. Same as the [Page
Down] and [Page Up] keys on a
computer keyboard.
54
FREEZE button
For freezing images.
58
BLACK SCREEN button
For superimposing a black screen.
52
RESIZE button
For switching the screen size
(NORMAL, BORDER, etc).
36
MUTE button
For temporarily turning off the
sound.
59
BREAK TIMER button
For displaying the break timer.
37
STANDBY button
For putting the projector into the
standby mode.
Remote Control (Top View)
Introduction
-13
23' (7 m)
30°
30°
45°
Using the Remote Control
■ The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
• The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
When using the remote control:
• Ensure that you do not drop the remote control or expose it to
moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluorescent lamp.
Inserting the Batteries
The batteries (two R-6 batteries (“AA” size,
UM/SUM-3, HP-7 or similar)) are included in
the package.
1 Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
2 Insert the included batteries.
• Insert the batteries making sure the
polarities correctly match the
and
marks inside the battery
compartment.
3 Insert the lower tab of the
cover into the opening, and
lower the cover until it clicks
in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Insert the batteries making sure the polarities correctly match the
and marks inside the battery compart-
ment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.
Battery fluid from leaked batteries is harmful to your skin, therefore ensure that you first wipe them and then
remove them using a cloth.
• The batteries included with this projector may exhaust over a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
Remote
control
sensor
Remote control
signal transmitters
Remote control
Available Range of the Remote Control
-14
Accessories
Remote control
RRMCGA176WJSA
Tw o R-6 batteries
(“AA” size, UM/SUM-3, HP-7 or similar)
Power cord
For U.S., Canada, etc.
(6' (1.8 m))
QACCDA007WJPZ
For Europe, except U.K.
(6' (1.8 m))
QACCVA011WJPZ
For U.K. and Singapore
(6' (1.8 m))
QACCBA036WJPZ
Note
• Use the power cord that corresponds to the wall outlet in your country.
■ 3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP2
Projector manual and
technical reference
CD-ROM
UDSKAA066WJZZ
(1)
(2) (3)
Supplied accessories
Optional cable
RGB cable
(9'10" (3 m))
QCNWGA045WJPZ
DIN-D-sub RS-232C
adaptor (5
57
/64'' (15 cm))
QCNWGA015WJPZ
Lens cap (attached)
PCAPHA003WJSA
Extra air filter
PFILDA017WJZZ
Quick guide label
TLABZA364WJZZ
Note
• This cable may not be available depending on the region. Please check with your nearest Sharp
Authorized Projector Dealer or Service Center.
USB cable (9'10" (3 m))
QCNWGA014WJPZ
Operation manual
(this manual)
Connections and Setup
Connections and Setup
-16
Connecting the Projector to Other Devices
Before Connecting
Note
• Before connecting, make sure the power cord of the projector from the AC outlet is unplugged, and that the
devices to be connected are turned off. After making all connections, turn on the projector and then the other
devices.
When connecting a computer, ensure that it is the last device to be turned on after all the connections are
made.
• Ensure that you have read the operation manuals of the devices to be connected before making connections.
This projector can be connected to:
A computer using:
■ An RGB cable and a computer audio cable (commercially available) (See page 17.)
■ A DIN-D-sub RS-232C adaptor and an RS-232C serial control
cable (commercially available) (See page 22.)
Component video or audio-visual equipment:
■ A VCR, Laser disc player or other audio-visual equipment
(See page 19.)
■ A DVD player or DTV* decoder (See page 20.)
*DTV is the umbrella term used to describe the new digital television
system in the United States.
An amplifier or audio components using:
■ An audio cable (commercially available) (See page 21.)
A monitor using:
■ An RGB cable (See page 23.)
■ A computer RGB cable (commercially available)
(See page 23.)
Connections and Setup
-17
Connecting the Power
Cord
Plug in the supplied power cord into
the AC socket on the rear of the projector.
Power code
Supplied
accessory
Connecting the Projector to a Computer
Connecting to a Computer
Using the RGB Cable
1 Connect the projector to the
computer using the supplied
RGB cable.
• Secure the connectors by tightening
the thumbscrews.
2
To input audio signal, connect
the projector to the computer
using the computer audio cable
(commercially available or available as Sharp service part
QCNWGA038WJPZ).
Note
• See page 93 “Computer Compatibility
Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may
cause some of the functions not to work.
• When connecting the projector to a computer in this way, select “RGB” for “Signal
Type” in the “Picture” menu. See page 46.
• A Macintosh
®
adaptor may be required for
use with some Macintosh
®
computers.
Contact your nearest Macintosh
®
Dealer.
•
Depending on the computer you are using,
an image may not be projected unless the
computer’s external output port is switched
on. (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP
notebook computer). Refer to the specific
instructions in your computer’s operation
manual to enable your computer’s external
output port.
Supplied
accessory
RGB cable
2
Computer audio cable (commercially
available or available as Sharp service
part QCNWGA038WJPZ)
To RGB output terminal
To audio output terminal
1
RGB cable
Notebook computer
-18
Connecting the thumbscrew cables
■ Connect the thumbscrew cable making sure that it
fits correctly into the terminal. Then, firmly secure
the connectors by tightening the screws on both
sides of the plug.
■ Do not remove the ferrite core attached to the RGB
cable.
Ferrite core
Connecting the Projector to Other Devices
“Plug and Play” function (when connecting to a 15-pin terminal)
■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
■ Before using the “Plug and Play” function, be sure to turn on the projector first and the connected
computer last.
Note
• The DDC “Plug and Play” function of this projector operates only when used in conjunction with a VESA
DDC compatible computer.
Connections and Setup
-19
Connecting to Video Equipment
1
S-video cable (commercially available)
Connecting to Video
Equipment Using an
S-video, a Composite
Video or an Audio Cable
Using an S-video, video, or audio cable, a VCR,
laser disc player or other audio-visual equipment can be connected to INPUT 3, INPUT 4
and AUDIO (L/R) input terminals.
1 Connect the projector to the
video equipment using an Svideo cable or a composite
video cable (both commercially
available).
2 Connect the projector to the
video equipment using an audio cable (commercially available).
Note
• The INPUT 4 (S-VIDEO) terminal uses a
video signal system in which the picture
is separated into color and luminance signals to realize a higher-quality image. To
view a higher-quality image, use a commercially available S-video cable to connect the INPUT 4 terminal on the projector and the S-video output terminal on the
video equipment.
To S-video output terminal
To video output terminal
To audio output terminal
2
Audio cable (commercially
available)
1
Composite video cable
(commercially available)
VCR or other audio-visual equipment
To analog component
output terminal
To audio output terminal
2
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
1
3 RCA to 15-pin
D-sub cable (sold separately)
DVD player or
DTV* decoder
Connecting to
Component Video
Equipment
Use a 3 RCA to 15-pin D-sub cable when connecting to the INPUT 1 or 2 terminal, component video equipment such as DVD players
and DTV* decoders.
*DTV is the umbrella term used to describe
the new digital television system in the United
States.
1 Connect the projector to the
video equipment using the 3
RCA to 15-pin D-sub cable
(sold separately).
2 Connect the projector to the
video equipment using a ø3.5
mm stereo minijack to RCA audio cable (commercially available).
Note
• When connecting the projector to the
video equipment in this way, select “Component” for “Signal Type” in the “Picture”
menu. See page 46.
• A ø3.5 mm stereo minijack to RCA audio
cable (commercially available) is required
for audio input.
-20
Connecting the Projector to Other Devices
Optional
cable
3RCA to 15-pin D-sub cable
AN-C3CP2
(9'10" (3.0 m))
Connections and Setup
-21
Connecting to an Amplifier
Connecting to an
Amplifier or Other Audio
Components
Using a ø3.5 mm stereo minijack to RCA audio cable, an amplifier or other audio components can be connected to the AUDIO OUTPUT terminal.
Connect the projector to the
amplifier
using a ø3.5 mm
stereo minijack
to
RCA
audio cable (commercially
available).
Info
• By using external audio components, the
volume can be amplified for better sound.
• The AUDIO OUTPUT terminal allows you
to output audio to audio components from
the selected AUDIO input terminal (for
INPUT 1 and 2) or AUDIO (L/R) input terminals (for INPUT 3 and 4) connected to
audiovisual equipment.
• For details on Variable Audio Output
(VAO) and Fixed Audio Output (FAO), see
page 63.
• A ø3.5 mm stereo minijack to RCA audio
cable (commercially available) is required
for audio input.
Amplifier
Audio input terminal
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Connecting the Projector to Other Devices
Controlling the Projector by a Computer
Connecting to a
Computer Using a DIND-sub RS-232C Adaptor
and an RS-232C Serial
Control Cable
When the RS-232C terminal on the projector
is connected to a computer with a DIN-D-sub
RS-232C adaptor and an RS-232C serial control cable (cross type, commercially available),
the computer can be used to control the projector and check the status of the projector.
See page 89 for details.
1 Connect the supplied DIN-D-
sub RS-232C adaptor to an RS232C serial control cable (commercially available).
2 Use the above cables to con-
nect the projector and the computer.
Supplied
accessory
Optional
cable
DIN-D-sub
RS-232C adaptor
RS-232C terminal
Desktop computer
DIN-D-sub
RS-232C adaptor
RS-232C serial control cable
(commercially available)
Note
• Do not connect or disconnect an RS-232C
serial control cable to or from the computer while it is on. This may damage your
computer.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
• See page 88 for connection of an RS232C serial control cable.
-22
Connections and Setup
-23
Optional
cable
Connecting to a Monitor
Watching Images on
Both the Projector and
a Monitor
You can display computer images on both the
projector and a separate monitor using two
sets of an RGB cable. An RGB cable is supplied with this projector. You need to buy another RGB cable for connecting the projector
to a monitor.
1
Connect the projector to the
computer and monitor using
RGB cables (one is supplied, the
other is commercially available).
2 In the “Options(1)” menu, se-
lect “Economy Mode”, “Mntr.
out/RS232” and then “ON”.
(see page 69.)
Note
• Analog RGB signals as well as Component
signals can be output to the monitor.
To RGB input terminal
Monitor
RGB cable
(commercially available)
RGB cable
(supplied)
Desktop computer
To RGB output terminal
Supplied
accessory
RGB cable
Connecting the Remote
Control to the Projector
When the remote control cannot be used due to
the range or positioning of the projector (rear projection, etc.), connect a ø3.5 mm stereo or mono
minijack cable (commercially available or available
as Sharp service part QCNWGA038WJPZ) from the
WIRED R/C JACK on the top of the remote control
to the WIRED REMOTE control input terminal.
Note
•
FORWARD/BACK presentation control cannot be used when the remote control is wired
to the projector. To utilize this feature, disconnect the cable from the remote control.
Using as a Wired Remote Control
ø3.5 mm stereo or mono
minijack cable
(commercially available or
available as Sharp service
part QCNWGA038WJPZ)
To WIRED R/C JACK
WIRED REMOTE control input terminal
-24
Using the Wireless Presentation Function of the
Remote Control
The Wireless Presentation function on the projector works the same as the [Page Up] and
[Page Down] keys on a computer keyboard. It can also be used to move forward or backward
when viewing images of presentation software such as Microsoft® PowerPoint®.
Using the Wireless Presentation Function
1 Connect the projector to the
computer using the supplied
USB cable.
Note
• This function only works with the
Microsoft® Windows® OS and Mac
®
OS. However, this function does not
work with the following operation
systems that do not support USB.
• Versions earlier than Windows
®
95.
• Versions earlier than Windows
®
NT4.0.
• Versions earlier than Mac® OS 8.5.
2 Press
or
while using
presentation software on your
computer.
• Press
to move the page up.
• Press
to move the page down.
USB cable
Computer
USB cable
USB terminal
FORWARD
button
BACK
button
-24
Connecting the Projector to Other Devices
Supplied
accessory
Connections and Setup
-25
Up
Down
Setup
Using the Adjustment
Feet
The height of the projector can be adjusted
using the adjustment feet at the front and back
of the projector when the surface the projector is placed on is uneven or when the screen
is slanted.
The projection of the image can be made
higher by adjusting the projector when it is in
a location lower than the screen.
1 Press HEIGHT ADJUST.
2 Lift the projector to adjust its
height and remove your finger
from HEIGHT ADJUST.
3 Rotate the adjustment feet at
the back of the projector for
fine adjustment.
Note
•
When returning the projector to its original
position, hold the projector firmly, press
HEIGHT ADJUST and then gently lower it.
• The projector is adjustable up to approximately 12 degrees on the front and 3
degrees on the back from the standard position.
Info
• Do not press HEIGHT ADJUST when the
adjustment foot is extended without firmly
holding the projector.
• Do not hold the lens when lifting or lowering the projector.
• When lowering the projector, be careful
not to get your finger caught in the area
between the adjustment foot and the
projector.
HEIGHT ADJUST
button
Adjustment feet
Adjustment foot
Zoom in
Zoom out
Zoom knob
Focus ring
Adjusting the Lens
The image is focused and adjusted to the
desired size using the focus ring or zoom
knob on the projector.
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by mov-
ing the zoom knob.
-26
Setup
Loading...