Sharp Notevision XG-C435X-L, Notevision XG-C465X-L Operation Manual

Page 1
DATA PROJECTOR
MODEL
XG-C465X-L XG-C435X-L
OPERATION MANUAL
Introduction
Quick Start
Setup
Basic Operation
Useful Features
Appendix
Page 2
IMPORTANT
For your assistance in reporting the loss or theft of your
Projector, please record the Model and Serial Numbers located on the bottom of the projector and retain this information.
Before recycling the packaging, please ensure that you
have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10.
Model No.: Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth / Blue : Neutral / Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by
the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch, Koreanisch und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, espagnol, italien, néerlandais, suédois, portugais, chinois, coréen et arabe. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español, italiano, holandés, sueco, portugués, chino, coreano y árabe. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano, olandese, svedese, portoghese, cinese, coreano e arabo. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans, Italiaans, Nederlands, Zweeds, Portugees, Chinees, Koreaans en Arabisch. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska, koreanska och arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano, Holandês, Sueco, Português, Chinês, Coreano e Árabe. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
Page 3
-1
Introduction
Before using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To r educe the risk of fire or electric shock, do not expose this product to
rain or moisture.
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equip­ment.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Introduction
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
See bottom of projector.
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Page 4
-2
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 786,432 pixels (x RGB) TFT’s (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or
other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the United States.
Adobe
®
Reader® is a trademark of Adobe Systems Incorporated.
Macintosh
®
is a registered trademark of Apple Computer , Inc. in the United States and/or other countries.
PJLink is a registered trademark or an application trademark in Japan, the United States and/or other
countries/regions.
All other company or product names are tr ademarks or registered trademarks of their respective compa-
nies.
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 61.
E.U. ONLY
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
Page 5
-3
Introduction
-43
Useful Features
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
This operation can also be performed by using the buttons on the projector.
MENU button
MOUSE/Adjustment buttons ('/"/\/|)
RETURN button
ENTER button
Press RETURN to return to previous screen when the menu is displayed
Adjustment buttons ('/"/\/|)
MENU button
ENTER button
RETURN button
Example: “Picture” screen menu
1
Press MENU.
The “Picture” menu screen for the se­lected input mode is displayed.
2
Press
||
||
| or
\\
\\
\ and select “Pic-
ture” to adjust.
Menu item
Picture Mode
Contrast 0
0 0 0
Bright Color Tint
0Sharp
Standard
7500K 3D Progressive Auto Off Off Off
SEL./ADJ. RETURN
ENTER END
Picture SIG SCR PRJ Net.
0 0
Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode
Reset
How to Read this Operation Manual
••
••
In this operation manual, the illustrations and on-screen displays are simplified for explana-
tion. This may differ from the actual on-screen display.
Info
...........Indicates safeguards when using the projector.
For Future Reference
Maintenance Troubleshooting Index
Page 70
Pages 66 and 67
Page 56
On-screen display
Button used in this step
Note
........Indicates additional information for setting up and operating the projector.
Buttons used in this operation
Buttons used in this operation
Page 6
-4
Contents
Preparing
Useful Features
Menu Items ................................................... 40
Using the Menu Screen ............................... 43
Menu Selections (Adjustments) ......................... 43
Picture Adjustment (“Picture” menu) ........ 45
Selecting the Picture Mode ............................... 45
Adjusting the Image .......................................... 45
Adjusting the Color Temperature ....................... 45
Selecting the Progressive Mode........................ 46
Selecting the Film Mode ....................................46
Reducing Image Noise (DNR) ........................... 46
Mosquito Noise Reduction (MNR) .....................46
Eco+Quiet Mode Setting ................................... 46
Signal Adjustment (“SIG-ADJ” Menu) ........ 47
Adjusting the Computer Image ......................... 47
Resolution Setting .............................................. 47
Auto Sync Adjustment ....................................... 47
Signal Type Setting ............................................ 47
Selecting the Dynamic Range ...........................48
Setting the Video System................................... 48
Checking the Input Signal ................................. 48
Screen Adjustment (“SCR-ADJ” Menu) ..... 49
Setting the Resize Mode ...................................49
Adjusting the Image Position ............................. 49
Keystone Correction ..........................................49
Setting the On-screen Display........................... 50
Selecting a Startup and Background Image .....50
Selecting the Menu Screen Position .................. 50
Reversing/Inverting Projected Images .............. 50
Selecting the On-screen Display Language ..... 50
Helpful Functions Set during Installation
(“PRJ-ADJ” menu) ................................. 51
Auto Power Off Function .................................... 51
Auto Restart Function ........................................ 51
Setting the Confirmation Sound
(System Sound) ........................................... 51
Speaker Setting ................................................. 51
Audio Output Type Setting ................................51
Monitor Output ................................................... 51
LAN/RS232C .....................................................51
Selecting the Transmission Speed (RS-232C) ..52
Fan Mode Setting .............................................. 52
System Lock Function ....................................... 52
Keylock Function ............................................... 53
Returning to the Default Settings ....................... 53
Checking the Lamp Life Status ......................... 53
Setting up the Projector Network
Environment (“Network” menu) ............ 54
Setting a Password ............................................ 54
DHCP Client Setting .......................................... 55
TCP/IP Setting ...................................................55
Confirming the Projector Information ................. 55
Introduction
How to Read this Operation Manual............. 3
Contents.......................................................... 4
How to Access the PDF Operation Manuals ....
6
IMPORTANT SAFEGUARDS .......................... 7
Accessories .................................................. 10
Part Names and Functions .......................... 12
Using the Remote Control ........................... 15
Usable Range .................................................... 15
Inserting the Batteries .......................................15
Quick Start
Quick Start .................................................... 16
Setup
Setting Up the Projector .............................. 18
Setting Up the Projector .................................... 18
Projection (PRJ) Mode ....................................... 19
Connections
Samples of Cables for Connection............. 21
Connecting to a Computer .......................... 23
Connecting to Video Equipment ................. 25
Controlling the Projector by a Computer... 27 Connecting to a Monitor with RGB
Input Terminal ......................................... 28
Connecting to an Amplifier or Other
Audio Equipment .................................... 29
Basic Operation
Turning the Projector On/Off ....................... 30
Connecting the Power Cord .............................. 30
Tur ning the Projector On.................................... 30
Tur ning the Power Off (Putting the Projector into
Standby Mode)............................................ 30
Image Projection .......................................... 31
Using the Adjustment Feet ................................ 31
Correcting Trapezoidal Distortion ...................... 32
Adjusting the Lens ............................................. 33
Switching the Input Mode .................................. 34
Adjusting the Volume......................................... 34
Displaying the Black Screen and Turning off
the Sound Temporarily ................................ 34
Displaying and Setting the Break Timer ............ 35
Switching the Eco+Quiet Mode ......................... 35
Auto Sync (Auto Sync Adjustment) ................... 35
Freezing a Moving Image .................................. 35
Selecting the Picture Mode ............................... 36
Displaying an Enlarged Portion of an Image .... 36
Resize Mode ...................................................... 37
Using the Remote Control as the Wireless
Computer Mouse ........................................ 39
Using
Page 7
-5
Introduction
Reference
Appendix
Maintenance ................................................. 56
Replacing the Air Filter ................................ 57
Replacing the Air Filter ...................................... 57
Maintenance Indicators ............................... 59
Regarding the Lamp .................................... 61
Lamp ................................................................. 61
Caution Concerning the Lamp .......................... 61
Replacing the Lamp .......................................... 61
Removing and Installing the Lamp Unit ............ 62
Resetting the Lamp Timer ................................. 63
Storing the Projector ................................... 64
How to Use the Storage Case ........................... 64
Computer Compatibility Chart .................... 65
Troubleshooting ........................................... 66
For SHARP Assistance................................ 68
Specifications............................................... 69
Index.............................................................. 70
SETUP MANUAL
Refer to the “SETUP MANU AL” contained on the supplied CD­ROM for details.
Setting up the Screen .................................... 2
Screen Size and Projection Distance ........... 3
Changing the Lens......................................... 9
Connecting Pin Assignments ..................... 11
RS-232C Specifications and Commands ... 13 Setting up the Projector Network
Environment............................................ 18
Controlling the Projector via LAN .............. 24
Setting up the Projector Using
RS-232C or Telnet................................... 29
Resetting the Lamp Timer
of the Projector via LAN......................... 39
Troubleshooting ........................................... 41
Wired Remote Control Terminal
Specifications ......................................... 44
Dimensions................................................... 45
Page 8
-6
PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector. To utilize these manuals, you need to install Adobe® Reader® on your computer (Windows® or Macintosh®).
Please download Adobe® Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals
For Windows®:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4
When you want to view the operation manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf file to access the pro­jector manuals.
When you want to view the setup manual
1) Double click the “SETUP” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf file to access the setup manual.
For Macintosh
®
:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “CD-ROM” icon. 3
When you want to view the operation manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf file to access the pro­jector manuals.
When you want to view the setup manual
1) Double click the “SETUP” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf file to access the setup manual.
How to Access the PDF Operation Manuals
Info
If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then specify the desired file using the “File”, “Open” menu.
Page 9
-7
Introduction
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with a
grounding terminal. This plug will only fit into a grounding type power outlet.
IMPORTANT SAFEGUARDS
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into
the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation. e. If the product has been dropped or damaged in any
way. f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, ensure that the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21.Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
Page 10
-8
Ensure that you read the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass par­ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Pro­jector Dealer or Service Cen­ter for replacement. See “Regarding the Lamp” on page 61.
Caution concerning the setup of the pro­jector
For minimal servicing and to maintain high image quality , SHARP recommends that this projector be installed in an area free from hu­midity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places ex­posed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
The projector may be safely tilted to a maximum angle of 9 degrees.
Placement should be within ±9 degrees of horizontal.
When using the projector in high-altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)
When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longe vity of the optical system.
Warning about placing the projector in a high position
When placing the projector in a high posi­tion, make certain it is carefully secured to avoid personal injury caused by the projec­tor falling down.
Do not subject the projector to hard im­pact and/or vibration.
Take care with the lens so as not to hit or damage the surface of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.
Avoid locations with extremes of tem­perature.
The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).
The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).
Do not block the intake and exhaust vents.
Allow at least 7 7/8 inches (20 cm) of space between the exhaust vent and the nearest wall or obstruction.
Ensure that the intake vent and the exhaust vent are not obstructed.
If the cooling fan becomes obstructed, a pro­tection circuit will automatically put the pro­jector into standby mode to prevent overheat damage. This does not indicate a malfunc­tion (see pages 59 and 60). Remove the pro- jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
CAUTION PRECAUCIÓN PRÉCAUTION
IMPORTANT SAFEGUARDS
Page 11
-9
Introduction
Caution regarding usage of the projector
When using the projector, take care not to sub­ject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. If you are not to use the projector for a long time, mak e certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.
Do not carry the projector by holding the lens.
When storing the projector, ensure you attach the lens cap to the projector. (See page 12.)
Do not expose the storage case or projector to direct sunlight or near heat sources. The storage case or projector may change color or become deformed.
Other connected equipment
When connecting a computer or other audio­visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.
Please read the operation manuals of the pro­jector and the equipment to be connected for instructions on how to make the connections.
Using the projector in other countries
The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.
Temperature monitor function
If the projector starts to over­heat due to setup problems or blockage of the air vents, “ ” and “ ” will illumi­nate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cool­ing-off period the projector will enter the standby mode. Refer to “Maintenance Indicators” on page 59 for details.
Info
The cooling fan regulates the internal tem­perature, and its performance is automati­cally controlled. The sound of the f an ma y change during projector operation due to changes in the fan speed. This does not indicate malfunction.
Page 12
-10
Accessories
Remote control <RRMCGA623WJSA>
Two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar)
Power cord
*
For U.S., Canada, etc. (6' (1.8 m)) <QACCDA007WJPZ>
For Europe, except U.K. (6' (1.8 m)) <QACCVA011WJPZ>
*Which power cords are supplied along with your projector depends on the region. Use the power cord
that corresponds to the wall outlet in your country.
Lamp unit AN-C430LP
Ceiling-mount adaptor AN-60KT
Ceiling-mount bracket AN-XGCM55 (for U.S.A. only)
Universal bracket AN-JT200 (for U.S.A. only)
Ceiling-mount unit AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
Ceiling-mount extension tube AN-EP101B <for AN-XGCM55 and AN-JT200> (for U.S.A. only)
Remote receiver AN-MR2
3 RCA to 15-pin D-sub cable (10' (3.0 m)) AN-C3CP2
Note
Some of the optional accessories may not be available depending on the region. Please check with your
nearest Sharp Authorized Projector Dealer or Service Center.
(1)
(2) (3)
(4)
DIN-D-sub RS-232C adaptor (5
57/64" (15 cm))
<QCNWGA091WJPZ>
Lens cap (attached) <PCAPHA026WJSA>
Supplied accessories
RGB cable (10' (3.0 m)) <QCNWGA086WJPZ>
For U.K., Hong Kong and Singapore (6' (1.8 m)) <QACCBA036WJPZ>
For Australia, New Zealand and Oceania (6' (1.8 m)) <QACCLA018WJPZ>
Storage case <GCASNA020WJSA>
Optional accessories
Lens cap strap <UBNDTA017WJZZ>
Operation manual (this manual <TINS-E323WJZZ> and CD-ROM <UDSKAA119WJZZ>)
Note
Codes in “< >” are Replacement parts codes.
Page 13
-11
Introduction
Optional lenses
Lens Projection distance for 100" screen size
Wide-zoom lens (× 1.5 – 1.9) AN-C12MZ 9'11" – 12'5" (3.0 m – 3.8 m) Tele-zoom lens (× 2.2 – 2.8) AN-C18MZ 14'10" – 18'10" (4.5 m – 5.7 m) Tele-zoom lens (× 3.3 – 5.1) AN-C27MZ 22' – 33'11" (6.7 m – 10.3 m) Tele-zoom lens (× 5.2 – 7.2) AN-C41MZ 34'5" – 48'4" (10.5 m – 14.7 m)
The standard zoom lens is attached to the projector. The optional lenses from Sharp are also available for specialized application. Please see your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the SETUP MANUAL on the supplied CD-R OM for details.) Also, be sure to have service person­nel install the optional lenses.
Throw Distance
The graph below is for 100 inches (254 cm) screen with 4:3 normal mode.
Screen
10 20 30 5040 (ft)
3.0 6.0 9.1 15.212.2 (m)
Standard zoom lens
11'9"–14'1" (3.6 m–4.3 m)
Throw distance ratio 1:1.8–2.1
Tele-zoom lens (AN-C18MZ)
14'10"–18'10" (4.5 m–5.7 m)
Throw distance ratio 1:2.2–2.8
Tele-zoom lens (AN-C27MZ)
22'–33'11" (6.7 m–10.3 m)
Throw distance ratio 1:3.3–5.1
Tele-zoom lens (AN-C41MZ)
34'5"–48'4" (10.5 m–14.7 m)
Throw distance ratio 1:5.2–7.2
Wide-zoom lens (AN-C12MZ)
9'11"–12'5" (3.0 m–3.8 m)
Throw distance ratio 1:1.5–1.9
Page 14
-12
43
MENU button
For displaying adjustment and setting screens.
44
35
AUTO SYNC button
For automatically adjusting images when connected to a computer.
ENTER button
For setting items selected or adjusted on the menu.
32
KEYSTONE button
For entering the Keystone
Correction mode.
30
STANDBY/ON button
For turning the power on and
putting the projector into
standby mode.
15
Remote control sensor
43
Adjustment buttons
('/"/\/|)
For selecting and adjusting
on-screen items.
51
Speaker
33
Focus ring
For adjusting the focus.
33
Zoom knob
For enlarging/
reducing the picture.
Air filter/Intake vent
(on the bottom of the projector)
Push both sides of the lens cap to
attach or remove.
RETURN button
For returning to the previous
display.
34
INPUT buttons
For switching input mode.
34
Volume buttons
For adjusting the speaker sound level.
59
Temperature warning indicator
30·59
Lamp indicator
30·59
Power indicator
31
Height Adjustment
button
31
Height Adjustment button
31
Tilt dial
31
Adjustment foot
Adjustment foot
ECO+QUIET button
For lowering the noise of the cooling fan and extending the lamp life.
35
43
56·57
31
Projector
Part Names and Functions
Numbers in refer to the main pages in this operation manual where the topic is explained.
Top View
Front View
Attaching the lens cap
After putting the lens cap strap on the lens cap, pass the other end of the strap through the hole on the front side of the projector, next to the lens, as shown in the illustration.
Page 15
-13
Introduction
Projector (Rear View)
* Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
56
Intake vent
Carrying handle
15
Remote control sensor
56
Exhaust vent
30
AC socket
Connect the supplied power cord.
* Kensington Security
Standard connector
LAN terminal
Terminal for controlling the projector using a computer via network.
28
RS-232C terminal
Terminal for controlling the projector using a computer.
27
USB terminal
Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.
39
COMPUTER/COMPONENT 2 input terminal
Terminal for Computer RGB and Component signals.
23·25
24·25
23·25
23·25
DVI-D input terminal
Terminal for DVI Digital RGB and Digital Component signals.
WIRED REMOTE terminal
For connecting the remote control to the projector when the signals from the remote control cannot reach the remote control sensor.
14
AUDIO input terminal
Shared audio input terminal for COMPUTER/COMPONENT 2 and DVI-D.
25
AUDIO output terminal
29
COMPUTER/COMPONENT 1
input terminal
Terminal for Computer RGB
and Component signals.
AUDIO input terminal
Audio input terminal for
COMPUTER/COMPONENT 1.
S-VIDEO input terminal
26
VIDEO input terminal
26
AUDIO input terminal
for Video
26
AUDIO input terminal
for S-video
26
28
MONITOR output terminal
Output terminal for Computer RGB and
Component signals.
Shared for COMPUTER/COMPONENT 1 and 2.
Terminals
Using the Carrying Handle
When transporting the projector, carry it by the carrying handle on the side.
Always put on the lens cap to prevent damage to the lens when transporting the projector.
Do not lift or carry the projector by the lens or the lens cap as this may damage the lens.
Page 16
-14
Remote Control
30
STANDBY button
For putting the projector into
standby mode.
32
KEYSTONE button
For entering the Keystone
Correction mode.
35
FREEZE button
For freezing images.
36
MAGNIFY (Enlarge/Reduce)
buttons
For enlarging/reducing part of the
image.
44
39
ENTER button
For setting items selected or
adjusted on the menu.
35
BREAK TIMER button
For displaying the break timer.
34
INPUT buttons
For switching to the respective
input modes.
35
AUTO SYNC button
For automatically adjusting images
when connected to a computer.
39
PAGE Up/Down buttons
Same as the [Page Down] and
[Page Up] keys on a computer
keyboard, when with the USB
connection (using a USB cable or
the optional remote receiver).
RESIZE button
For switching the screen size (NORMAL, STRETCH, etc.).
37
PICTURE MODE button
For switching the picture mode.
36
Volume buttons
For adjusting the speaker sound level.
34
AV MUTE button
For temporarily displaying the black screen and turning off the sound.
34
MENU button
For displaying adjustment and setting screens.
43
WIRED R/C JACK
For controlling the projector by connecting the remote control to the projector.
ON button
For turning the power on.
30
L-CLICK button
For the Left click when with the
USB connection (using a USB
cable or the optional
remote receiver).
MOUSE/Adjustment buttons ('/"/\/|)
For moving the computer cursor when with the USB connection (using a USB cable or the optional remote receiver).
For selecting and adjusting on­screen items.
R-CLICK/RETURN button
For the Right click when with the USB connection (using a USB cable or the optional remote receiver).
For returning to the previous display.
ECO+QUIET button
For lowering the noise of the cooling fan and extending the lamp life.
35
39·43
39·43
Part Names and Functions
Using the Remote Control with a Signal Cable
When the signals from the remote control cannot be reached due to the positioning of the projector, use a ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector with the remote control.
Projector
(Rear view)
Remote control
To WIRED R/C JACK
To WIRED REMOTE terminal
ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNWGA038WJPZ)
Note
The wireless remote function is not possible when the ø3.5 mm minijack cab le is connected to the projector. Should the wireless remote operation be required, the ø3.5 mm minijack cable should be disconnected from the projector.
Page 17
-15
Introduction
Using the Remote Control
Inserting the Batteries
1
Pull down the tab on the cover and remove the cover towards the di­rection of the arrow.
2 Insert the batteries.
Insert the batteries making sure the po­larities correctly match the and marks inside the battery compartment.
3 Insert the lower tab of the cover
into the opening, and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the
and marks inside the battery compart-
ment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Usable Range
The remote control can be used to control the projector within the ranges shown in the il­lustration.
Note
The signal from the remote control can be re­flected off a screen for easy operation. How­ever, the effective distance of the signal may differ depending on the screen material.
When using the remote control:
Take care not to drop, expose to moisture or high temperature.
The remote control may malfunction under a fluorescent lamp. In this case, move the pro­jector away from the fluorescent lamp.
Remote control sensor
Remote control signal transmitters
Remote control
23' (7 m)
30°
30°
30°
Front View
Rear View
30°
30°
30°
Remote control sensor
23' (7 m)
Remote control signal transmitters
Remote control
Page 18
-16
Quick Start
7 STANDBY
button
3 ON button
6 COMPUTER 1
button
37 STANDBY/ON button 6 INPUT buttons
6 ENTER button
4 Height Adjustment buttons
5 Zoom knob
5 Focus ring
4 Tilt dial
Page 18
1. Place the projector facing a screen
Pages 23, 30
Page 30
On the remote controlOn the projector
This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
2. Connect the projector to the computer and plug the power
cord into the AC socket of the projector
3. Remove the lens cap and turn the projector on
When connecting equipment other than the computer, see pages 25, 28 and 29.
Page 19
-17
Quick Start
Pages 31, 32
4. Adjust the angle
5. Adjust the focus and the zoom
7. Tu rn the Power off
Page 30
6. Select the INPUT mode
Page 34
••
••
This projector is equipped with an “Auto V-Keystone Correction” function that automatically corrects any trapezoidal distortion within the projected image.
Bring the projected image into focus
••
••
Bring the projected image into focus by
rotating the focus ring.
Adjust the projected image size
••
••
Adjust the projected image size by moving the
zoom knob.
Select the “COMPUTER 1” using the INPUT buttons on the projector or the COMPUTER 1 button on the remote control.
••
••
When you press the INPUT buttons on the projector, the INPUT list appears. Press
''
''
'/
""
""
" to select an item on the list, and press ENTER to switch to the selected INPUT mode.
••
••
When using the remote control, press COMPUTER1/2, DVI, S-VIDEO or VIDEO to
switch the INPUT mode.
On the remote
control
On the
projector
""
""
" INPUT list
Press the STANDBY button, then press that button again while the confirmation message is displayed, to put the projector into standby mode.
••
••
Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.
On the remote controlOn the projector
""
""
" On-screen Display
Adjust the projector angle
••
••
Adjust the projector angle using the Height Adjustment buttons.
••
••
Rotate the Tilt dial to adjust the horizontal tilt of the projector.
Height Adjustment buttons
Tilt dial
Focus ring
Zoom knob
Zoom in
Zoom out
""
""
" On-screen Display (RGB)
RGB 1024 × 768
COMPUTER1
INPUT
COMPUTER1
COMPUTER2 DVI-D Computer
D
Page 33
Page 20
-18
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 32.)
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according
to the desired picture size. (For details, refer to the “SETUP MANUAL” con­tained on the supplied CD-ROM.)
Example of standard setup
Setting Up the Projector
Side View
H
Screen
L: Projection distance
Lens center
Base line: Horizontal line passing through the lens center
Ceiling-mount Setup
It is recommended that you use the optional Sharp ceil-
ing-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Au­thorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold sepa­rately).
Page 21
-19
Setup
Projection (PRJ) Mode
The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appro­priate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 50.)
Table mounted, front projection Ceiling mounted, front projection
[Menu item “Front”] [Menu item “Ceiling + Front”]
Table mounted, rear projection Ceiling mounted, rear projection
(with a translucent screen) (with a translucent screen)
[Menu item ➞ “Rear”] [Menu item ➞ “Ceiling + Rear”]
Indication of the Projection Image Size and Projection Distance
For details, refer to the “SETUP MANUAL” contained on the supplied CD-ROM. Example: NORMAL Mode (4:3) for standard lens
500"
200" 100"
84" 60"
400"×300"
Projection Distance
160"
×
120"
80"
×
60"
67"
×
50"
48"
×
36"
58'7
"
70'4
"
(17.9 m – 21.4 m)
23'5
"–
28'1
"
(7.1 m
8.6 m)
11'9
"–
14'1
"
(3.6 m
4.3 m)
9'10
"–
11'10
"
(3.0 m
3.6 m)
7'0
"–
8'5
"
(2.1 m – 2.6 m)
Picture Size
Page 22
-20
Standard Zoom Lens
F1.7-F1.9, f=28.0-33.6 mm
Setting Up the Projector
Note
Allow a margin of error in the value in the diagrams above.
When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates
that the bottom of the image is below the lens center.
See page 18 about projection distance [L] and distance from the lens center to the bottom of the image [H].
NORMAL Mode (4:3)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.03571
χ
L2 (m) = 0.04286
χ
H (cm) = –0.1524
χ
[Feet/inches]
L1 (ft) = 0.03571χ / 0.3048 L2 (ft) = 0.04286χ / 0.3048 H (in) = –0.1524
χ
/ 2.54
χ
: Picture size (diag.) (in/cm) L: Projection distance(m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture size and projection distance
[m/cm]
L1 (m) = 0.0389
χ
L2 (m) = 0.04669
χ
H (cm) = 0.04151
χ
S (cm) = ±0.20754
χ
[Feet/inches]
L1 (ft) = 0.0389χ / 0.3048 L2 (ft) = 0.04669
χ
/ 0.3048 H (in) = 0.04151χ / 2.54 S (in) = ±0.20754χ / 2.54
χ
: Picture size (diag.) (in/cm) L: Projection distance(m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the lens center to the bottom of the image (cm/in) S: Adjustable range of image position (cm/in)
STRETCH Mode (16:9)
Picture (Screen) size Projection distance [L]
Distance from the lens center to the bottom of the image [H]
500'' (1270 cm) 1016 cm (400'') 762 cm (300'') 17.9 m(58' 7") 21.4 m (70' 4") –76 cm (–30")
300'' (762 cm) 610 cm (240'') 457 cm (180'') 10.7 m (35' 2") 12.9 m (42' 2") –46 cm (–18")
270'' (686 cm) 549 cm (216'') 411 cm (162'') 9.6 m (31' 8") 11.6 m (38') –41 cm (–16
13
/64") 250'' (635 cm) 508 cm (200'') 381 cm (150'') 8.9 m (29' 3") 10.7 m (35' 2" ) –38 cm (–15") 200'' (508 cm) 406 cm (160'') 305 cm (120'') 7.1 m (23' 5") 8.6 m (28' 1") –30 cm (–12") 150'' (381 cm) 305 cm (120'') 229 cm (90'') 5.4 m (17' 7") 6.4 m (21' 1") –23 cm (–9") 100'' (254 cm) 203 cm (80'') 152 cm (60'') 3.6 m (11' 9") 4.3 m (14' 1") –15 cm (–6")
84'' (213 cm) 171 cm (67'') 128 cm (50'' ) 3.0 m (9' 10") 3.6 m (11' 10") –13 cm (–5
3
/64")
80'' (203 cm) 163 cm (64'') 122 cm (48'' ) 2.9 m (9' 4") 3.4 m (11' 3") –12 cm (–4
51
/64")
72'' (183 cm) 146 cm (58'') 110 cm (43'' ) 2.6 m (8' 5") 3.1 m (10' 1") –11 cm (–4
5
/16")
60'' (152 cm) 122 cm (48'') 91 cm (36' ' ) 2.1 m (7') 2.6 m (8' 5" ) –9 cm (–3
19
/32")
40'' (102 cm) 81 cm (32'') 61 cm (24'') 1.4 m ( 4' 8") 1.7 m (5' 7") –6 cm (–2
13
/32")
Diag. [χ]Width Height Minimum [L1] Maximum [L2]
Picture (Screen) size Projection distance [L]
Distance from the lens center to the bottom of the image [H]
Adjustable range of image position [S]
Diag. [χ]Width Height Minimum [L1] Maximum [L2]
450'' (1143 cm) 996 cm (392'') 560 cm (221' ' ) 17.5 m(57' 5") 21.0 m (68' 11") 19 cm (7 23/64") ±93 cm (±36 49/64") 300'' (762 cm) 664 cm (261'') 374 cm (147'') 11.7 m (38' 3") 14.0 m (45' 11") 12 cm (4
29
/32") ±62 cm (±24 33/64")
250'' (635 cm) 553 cm (218'') 311 cm (123'') 9.7 m ( 31' 11" ) 11.7 m (38' 4") 10 cm (4
5
/64") ±52 cm (±20 27/64")
225'' (572 cm) 498 cm (196'') 280 cm (110'') 8.8 m (28' 9") 10.5 m (34' 6") 9 cm (3
43
/64") ±47 cm (±18 25/64")
200'' (508 cm) 443 cm (174'') 249 cm (98'') 7.8 m (25' 6") 9.3 m (30' 8") 8 cm (3
17
/64") ±42 cm (±16 11/32")
150'' (381 cm) 332 cm (131'') 187 cm (74'') 5.8 m (19' 2") 7.0 m (23') 6 cm (2
29
/64") ±31 cm (±12 1/4")
133'' (338 cm) 294 cm (116'') 166 cm (65'') 5.2 m (17') 6.2 m (20' 4") 6 cm (2
11
/64") ±28 cm (±10 7/8")
106'' (269 cm) 235 cm (92'') 132 cm (52'') 4.1 m (13' 6") 4.9 m (16' 3") 4 cm (1
47
/64") ±22 cm (±8 21/32")
100'' (254 cm) 221 cm (87'') 125 cm (49'') 3.9 m (12' 9") 4.7 m (15' 4") 4 cm (1
41
/64") ±21 cm (±8 11/64")
92'' (234 cm) 204 cm (80'') 115 cm (45'') 3.6 m (11' 9") 4.3 m (14' 1") 4 cm (1
1
/2") ±19 cm (±7 33/64")
84'' (213 cm) 186 cm (73'') 105 cm (41'') 3.3 m (10' 9") 3.9 m (12' 10") 3 cm (1
3
/8") ±17 cm (±6 55/64")
80'' (203 cm) 177 cm (70'') 100 cm (39'') 3.1 m (10' 3") 3.7 m (12' 3") 3 cm (1
5
/16") ±17 cm (±6 17/32")
72'' (183 cm) 159 cm (63'') 90 cm (35' ' ) 2.8 m (9' 2") 3.4 m (11') 3 cm (1
11
/64") ±15 cm (±5 57/64")
60'' (152 cm) 133 cm (52'') 75 cm ( 29'') 2. 3 m (7' 8") 2.8 m (9' 2") 2 cm (
63
/64") ±12 cm (±4 29/32")
40'' (102 cm) 89 cm (35'') 50 cm (20'') 1.6 m (5' 1") 1.9 m (6' 2") 2 cm (
21
/32") ±8 cm (±3 17/64")
Page 23
-21
Samples of Cables for Connection
•For more details of connection and cables, refer to the operation manual of the connecting equipment.
•You may need other cables or connectors not listed below.
Terminal on the
projector
COMPUTER/ COMPONENT 1, 2
DVI-D
AUDIO
(for COMPUTER/ COMPONENT 1, 2, DVI-D)
DVI-D
COMPUTER/ COMPONENT 1, 2
S-VIDEO
VIDEO
Equipment
Computer
Audio-visual equipment
Terminal on
connected equipment
RGB
output
terminal
DVI digital
video
output
terminal
Audio
output
terminal
DVI digital
video
output
terminal
Component
video
output
terminal
Terminal
for using
the
dedicated
cable
S-video
output
terminal
Video output
terminal
Cable
RGB cable (supplied)
DVI Digital cable (commercially available)
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ)
DVI Digital cable (commercially available)
3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)
Connect with the cable adaptor, etc.
S-video cable (commercially available)
Video cable (commercially available)
Cable adaptor (commercially available)
3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)
Dedicated cable
Page 24
-22
Terminal on the
projector
AUDIO
(for COMPUTER/ COMPONENT 1, 2, DVI-D)
AUDIO
(for VIDEO, S-VIDEO)
MONITOR OUTPUT
AUDIO
(MONITOR OUT)
Equipment
Audio-visual equipment
Monitor
Amplifier
Terminal on
connected equipment
Audio output
terminal
Terminal
for using
the
dedicated
cable
Audio output
terminal
Terminal
for using
the
dedicated
cable
RGB
input
terminal
Audio
input
terminal
Cable
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
Connect with the cable adaptor, etc.
RCA audio cable (commercially available)
Connect with the cable adaptor, etc.
RGB cable (supplied or commercially available)
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
Cable adaptor (commercially available)
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
Dedicated cable
Cable adaptor (commercially available)
RCA audio cable (commercially available)
Dedicated cable
Samples of Cables for Connection
Page 25
-23
Connecting to a Computer
Before connecting, ensure the power cord of the projector from the AC outlet is unplugged, and that the devices to be connected are turned off. After making all connections, turn on the projector and then the other devices. When connecting a computer, ensure that it is the last device to be turned on after all the connections are made.
Ensure the operation manuals of the devices to be connected have been read before making connections.
When connecting with the RGB cable
(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)
To audio output terminal
To RGB output terminal
*
ø3.5 mm stereo or mono audio cable
(commercially available or available as Sharp service part QCNWGA038WJPZ)
To COMPUTER/ COMPONENT 1 input terminal
Computer
To AUDIO input terminal
RGB cable
*
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
Note
See page 65 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work.
A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the computer’s
external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a
SHARP notebook computer). Refer to the specific instructions in your computer’s operation manual to
enable your computer’s external output port.
RGB cable
Supplied
accessory
Page 26
-24
When connecting with a DVI digital cable
The projector employs the DVI digital input terminal for direct input of Digital Video signals from a computer.
*
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.
Computer
* ø3.5 mm stereo or mono audio cable
(commercially available or available as Sharp service part QCNWGA038WJPZ)
To DVI-D input terminal
DVI Digital cable (commercially available)
To DVI digital output terminal
To audio output terminal
To AUDIO input terminal (for DVI-D)
Connecting to a Computer
Page 27
-25
Connecting to Video Equipment
The image quality is highest in order of the Component signal, the RGB signal, the S-video signal and the Video signal. If y our audio-visual equipment has a component output terminal or RGB output terminal, use the COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection.
When connecting video equipment with a DVI output terminal
Note
Select the input signal type of the video equipment. See page 47.
While the projector is connected to video equipment that has an HDMI output terminal, only the video
signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission may not work property. (The HDMI specification does not support all connections to video equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)
For details on compatibility for connection, see support information on DVI connection provided by the video equipment manufacturer.
When connecting video equipment with component video output terminal
(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)
Note
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a commercially available cable that fits in the projector terminal you want to connect.
The projector does not support RGBC signals via the Euro-scar t.
DVI Digital cable (commercially available)
To audio output terminals
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
To DVI output terminal
Video Equipment
To DVI-D input terminal
To AUDIO input terminal (for COMPUTER/COMPONENT 2, DVI-D)
To audio output terminal
ø3.5 mm minijack to RCA audio cable (commercially available)
3 RCA (Component) to 15-pin D-sub cable (optional: AN-C3CP2)
To component video output terminal
To COMPUTER/COMPONENT 1 input terminal
To AUDIO input terminal
Video Equipment
Page 28
-26
When connecting video equipment with S-video output terminal
When connecting video equipment with video output terminal
Note
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a com­mercially available cable that fits in the projector terminal you want to connect.
RCA audio cable (commercially available)
To audio output terminal
To S-video output terminal
S-video cable (commercially available)
To S-VIDEO input terminal
To AUDIO input terminal
Video Equipment
RCA audio cable (commercially available)
To audio output terminal
To video output terminal
Composite video cable (commercially available)
To VIDEO input terminal
To AUDIO input terminal
Video Equipment
Connecting to Video Equipment
Page 29
-27
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifications and Commands”.
When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor
Note
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.
Info
Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.
Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.
Computer
To RS-232C terminal
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
DIN-D-sub RS-232C adaptor
DIN-D-sub RS232C adaptor
Supplied
accessory
Page 30
-28
To RGB input terminal
RGB cable (commercially available)
RGB cable
To RGB output terminal
To COMPUTER/ COMPONENT 1 input terminal
To MONITOR OUT terminal
Monitor
Computer
When connecting to the LAN terminal using a LAN cable
Note
When connecting to hub, use straight-through Category 5 (CAT.5) type cable (commercially available).
When connecting to computer, use cross-over Category 5 (CAT.5) type cable (commercially available).
TX/RX LED (yellow) Illuminates when transmitting/receiving data. LINK LED (green) Illuminates when linked.
To LAN terminal
LAN cable (Category 5 type, commercially available)
HUB
or
Computer
*To ensure safety , do not connect the
LAN terminal with any cables such as a telephone line that may cause excessive voltage.
RGB cable
Supplied
accessory
Connecting to a Monitor with RGB Input Terminal
You can display computer images on both the projector and a separate monitor using two sets of RGB cables.
Controlling the Projector by a Computer
Page 31
-29
Audio signals input from equipment connected to each audio input terminal of the projector can be output to audio equipment.
Note
Turn off the power of both the projector and audio equipment when connecting.
When turning off the power in the case of connecting an amplifier or other audio equipment, first turn off
the power of the amplifier and then turn off the power of the projector.
By using external audio components, the volume can be amplified for better sound.
For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 52.
Connecting to an Amplifier or Other Audio Equipment
Amplifier
To AUDIO output terminal (MONITOR OUT)
To audio input terminal
ø3.5 mm minijack to RCA audio cable (commercially available)
Page 32
-30
AC socket
To AC outlet
Turning the Projector On/Off
Info
When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 51.)
English is the factory preset language. If you want to change the on-screen display to another language, change the language according to the procedure on page 50.
On-screen Display
Info
Direct Power Off function:
You can unplug the power cord from the AC outlet even if the cooling fan is still running.
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into the AC outlet.
Turning the Projector On
Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 23-29.)
Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.
The power indicator illuminates green.
After the lamp indicator illuminates, the projec-
tor is ready to start operation.
Note
The lamp indicator illuminates or blinks, in­dicating the status of the lamp.
Green: The lamp is on. Blinking green: The lamp is warming up.
Red:
The lamp is shut down abnor­mally or the lamp should be replaced.
When switching on the projector , a slight flic k er­ing of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilizing the lamp output charac­teristics. This does not indicate malfunction.
If the projector is put into standby mode and immediately turned on again, the lamp may take some time to illuminate.
When System Lock is set, the keycode in­put box appears. To cancel the keycode set­ting, input the keycode that you have already set. See page 52 for details.
Turning the Power Off
(Put-
ting the Projector into Standby Mode)
Press STANDBY/ON on the projector or STANDBY on the remote control, then press
that button again while the confirmation mes­sage is displayed, to put the projector into standby mode.
ON button
STANDBY button
Lamp indicator
Power indicator
STANDBY/ON button
Power cord
Supplied accessory
Page 33
-31
Basic Operation
Image Projection
Height Adjustment button
Side View
Lens center
Top View
Using the Adjustment Feet
The height of the projector can be adjusted using the adjustment feet when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpen­dicular to the screen as possible.
1
Press the Height Adjustment but­tons.
The adjustment feet come out.
2
Lift the projector to adjust its height and remove your hands from the
Height Adjustment
but-
tons
.
The projector is adjustable up to approxi­mately 9 degrees.
3 Rotate the Tilt dial to finely ad-
just the horizontal tilt of the pro­jector.
The inclination is adjustable within ap­proximately 2 degrees.
When adjusting the height of the pro­jector, trapezoidal distortion occurs. When “Auto V-Keystone” of the “SCR­ADJ” menu is set to “On” (see page 49), keystone correction functions automati­cally to correct trapezoidal distortion. When you want to adjust the automati­cally corrected image, use the manual keystone correction. (See page 32.)
Info
Do not press the Height Adjustment button when the adjustment feet come out without firmly holding the projector.
Do not hold the lens when lifting or lower­ing the projector.
When lowering the projector, be careful not to get your fingers caught in the area be­tween the adjustment foot and the projector .
Adjustment foot
Tilt dial
Page 34
-32
Image Projection
END TESTPATTERN
ADJUST RESET
H&V KEYSTONE H: 0 V: 0
"On-screen Display (Keystone Correction mode)
KEYSTONE button
MOUSE/Adjustment buttons ('/"/\/|)
RETURN button
Note
Press RETURN to return to the default set- ting.
Straight lines or the edges of images may appear jagged while adjusting the image.
The Manual Keystone Correction can be adjusted up to an angle of approximately ±50 degrees vertically and approximately ±30 degrees horizontally.
Correcting Trapezoidal Distortion
Auto V-Keystone Correction
When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. This projector is equipped with an “Auto V-Key­stone Correction” function that automatically cor­rects any trapezoidal distortion within the pro­jected image. The correction is made automatically provided the vertical incline or decline is within ±12 degrees.
Note
When not using the Auto V-Keystone Cor­rection function, set “Auto V-Keystone” on the “SCR-ADJ” menu to “Off”.
Manual Keystone Correction
When you want to make fine adjustments after the Auto V-Keystone Correction function has been acti­vated, or when you want to make corrections without using the Auto V-Keystone Correction function, you can make corrections manually using the following procedure.
1
Press KEYSTONE on the remote control to enter the Keystone Correc­tion mode.
You can also use KEYSTONE on the projector.
2 Press ' or " to parallelize the
left and right sides, or press \ or | to parallelize the upper and lower sides of the projected image.
You can also adjust the Keystone Cor­rection using the
''
''
'/
""
""
" and
\\
\\
\/
||
||
| buttons
on the projector.
3 Press
KEYSTONE
.
The on-screen display of the Keystone Correction mode will disappear.
You can also use KEYSTONE on the projector.
Vertical Keystone Correction (Adjustment with
' / "
)
Horizontal Keystone Correction (Adjustment with
\ / |
)
Page 35
-33
Basic Operation
Adjusting the Lens
The image is focused and adjusted to the screen size using the focus ring or zoom knob on the projector.
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by moving
the zoom knob.
Focus ring Zoom knob
Zoom in
Zoom out
Page 36
-34
Image Projection
COMPUTER 1, COMPUTER 2, DVI, S-VIDEO, VIDEO buttons
VOL +/– (Volume) buttons
AV MUTE button
Switching the Input Mode
Select the appropriate input mode for the con­nected equipment.
Press COMPUTER1/2, DVI, S-VIDEO or VIDEO on the remote control to se­lect the input mode.
When you press INPUT on the projector or DVI on the remote control, the INPUT list appears. Press
''
''
'/
""
""
" to switch the INPUT mode.
Adjusting the Volume
Press VOL +/– on the remote control or –\/ |+ on the projector to adjust the volume.
Note
Pressing VOL–/–
\\
\\
\ will lower the volume.
Pressing VOL+/
||
||
|+ will raise the volume.
When the projector is connected to exter­nal equipment, the volume level of the ex­ternal equipment changes in accordance with the volume level of the projector. Set the projector’s volume to the lowest level when turning the projector on/off or when changing the input signal.
When you do not want to output the sound from the projector’s speaker while the pro­jector is connected to external equipment, set “Speaker” in “PRJ-ADJ” menu to “Off ”. (See page 51.)
Displaying the Black Screen and Turning off the Sound Temporarily
Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound.
Note
Pressing AV MUTE again will turn the pro- jected image back on.
On-screen display
On-screen display
Page 37
-35
Basic Operation
Displaying and Setting the Break Timer
1 Press BREAK TIMER.
The timer starts to count down from 5 min­utes.
On-screen display
2 Press '/"/\/| to adjust the length
of the break time.
Increases with ' or |
5 minutes s 6 minutes s 60 minutes
Shortens with \ or "
4 minutes s 3 minutes s 1 minute
The break time can be set in units of one minute (up to 60 minutes).
Press BREAK TIMER.
Note
Break Timer does not function while the projec­tor is operating the “Auto Sync”, “FREEZE” or “AV MUTE” functions.
Switching the Eco+Quiet Mode
Press ECO+QUIET to switch the Eco+Quiet mode between on and off.
When the Eco+Quiet Mode is set to “ON”, the sound of the cooling fan will turn down, the power consump­tion will decrease, and the lamp life will extend.
Note
Refer to “Checking the Lamp Life Status” on
page 53 for details of the Eco+Quiet mode.
Auto Sync (Auto Sync Adjustment)
Auto Sync function works when detecting input signal after the projector turns on.
Press AUTO SYNC to manually adjust with Auto Sync function.
Note
When the optimum image cannot be achieved
with Auto Sync adjustment, use manual adjust­ments. (See page 47.)
Freezing a Moving Image
1 Press FREEZE.
The projected image is frozen.
2 Press FREEZE again to return to
the moving image from the cur­rently connected device.
MOUSE/Adjustment buttons ('/"/\/|)
FREEZE button
AUTO SYNC button
BREAK TIMER button
ECO+QUIET button
Canceling the break timer display function
Page 38
-36
Selecting the Picture Mode
You can select the appropriate picture mode for the projected image, such as movie or video game.
Press PICTURE MODE.
When pressing PICTURE MODE, the picture mode changes in the following order:
STANDARD PRESENTATION MOVIE GAME sRGB
Note
See page 45 for details on the picture mode.
* “sRGB” is displayed only when RGB signal is input.
Displaying an Enlarged Portion of an Image
Graphs, tables and other portions of projected images can be enlarged. This is helpful when
providing more detailed explanations.
1 Press MAGNIFY on the remote
control.
Enlarges the image.
Pressing
or MAGNIFY enlarges or
reduces the projected image.
Note
×1 ×2 ×3 ×4 ×9
Press
.
Press
.
You can change the location of the en­larged image using
''
''
',
""
""
",
\\
\\
\ and
||
||
|.
2 Press RETURN on the remote con-
trol to cancel the operation.
The magnification then returns to ×1.
Note
The selectable magnifications differ de­pending on the input signal.
In the following cases, the image will re­turn to the normal size (×1).
- When switching the INPUT mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and re-
fresh rate (vertical frequency) change.
- When the Resize mode is changed.
- When the Picture mode is changed.
Image Projection
MOUSE/Adjustment buttons ('/"/\/|)
RETURN button
PICTURE MODE button
MAGNIFY buttons
Page 39
-37
Basic Operation
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De­pending on the input signal, you can choose a desired image.
Press RESIZE.
See page 49 for setting on menu screen.
RESIZE button
COMPUTER
STRETCH
For 4:3 screen For 16:9 screen
Input signal
Image type
NORMAL FULL BORDER
4:3 aspect ratio
5:4 aspect ratio
16:10 aspect ratio
16:9 aspect ratio
Computer
Resolution lower than
XGA
XGA
Resolution
higher than
XGA
SXGA (1280 ´ 1024)
1280 ´ 720
1280 ´ 768
1280 ´ 800
1360 ´ 768 1366 ´ 768
DOT BY DOT
*2
*2*2
*1 *1
*2
*1 *1*1
*1
: Cutout area on which images cannot be projected : Area where the signals are off screen
*1
The Image Shift function can be used for these images.
*2
Same as NORMAL mode.
4:3 aspect ratio
Other aspect ratios
SVGA (800 × 600) XGA (1024 × 768)
SXGA (1152 × 864)
SXGA+ (1400 × 1050)
SXGA (1280 × 1024)
1280 × 720 1360 × 768 1366 × 768 1280 × 768 1280 × 800
1024 × 768
968 × 768 1024 × 576 1024 × 578 1024 × 576 1024 × 614 1024 × 640
1024 × 768
768 × 576
— —
— 960 × 576 922 × 576
1024 × 576
— — —
1024 × 576
NORMAL
FULL BORDER STRETCHDOT BY DOT
800 × 600 1024 × 768 1152 × 864
1400 × 1050 1280 × 1024
1280 × 720 1360 × 768 1366 × 768 1280 × 768 1280 × 800
Page 40
-38
VIDEO/DTV
Image Projection
About Copyrights
• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance . Keep this in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.
: Cutout area on which images cannot be projected : Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images. *2 Same as NORMAL mode.
4:3 aspect ratio
Squeeze
Letter box
16:9 aspect ratio
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
For 4:3 screen For 16:9 screen
Input signal
Image type NORMALVideo/DTV
480I, 480P, 576I, 576P,
NTSC, PAL,
SECAM
720P, 1035I,
1080I
540P
BORDER STRETCH
AREA ZOOM
V-STRETCH
*1 *1
*1 *1
*1 *1
*2*2
*1
*1
Page 41
-39
Basic Operation
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the separately sold remote receiver (AN-MR2) makes it possible to operate the projector with the remote control. For de-
tails, see the operation manual of the receiver.
Connecting with a USB cable
The mouse pointer can be operated in the following way after it is connected.
When moving the cursor
Press MOUSE/Adjustment buttons ('/"/\/|).
When left-clicking
Press L-CLICK.
When right-clicking
Press R-CLICK.
When your computer supports only a one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function.
Note
This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function does not work with the following operation systems that do not support USB.
Versions earlier than Windows® 95
Versions earlier than Windows
®
NT4.0
Versions earlier than Mac OS
®
8.5
You cannot use this function when displaying the menu screen.
Confirm that the computer recognizes the USB connection.
When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE DOWN.
To USB terminal
USB terminal
or
USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)
Point the remote control at the
USB remote receiver
(AN-MR2, optional)
Computer
MOUSE/Adjustment buttons ('/"/\/|)
R-CLICK button
L-CLICK button
PAGE Up/Down buttons
Page 42
-40
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
+30-30
+30-30
+30-30
+30-30
+30-30 +30-30
Tint
Color
Reset
Sharp
Bright
+30-30
Contrast
Red Blue
Progressive
Picture
Main Menu
Sub Menu
CLR Temp
Page 45
Page 45
Page 45
Page 45
Page 46
Page 45
Picture Mode
Standard Presentation Movie Game sRGB
*1
*2
*2
*2
*3
*3
3D Progressive 2D Progressive
5500K 6500K 7500K 8500K 9300K 10500K
Film Mode
Page 46
Auto Off
Eco+Quiet Mode
Page 46
On Off
DNR
Page 46
Off Level 1 Level 2 Level 3
MNR
Page 46
Off Level 1 Level 2 Level 3
*1 Item when inputting RGB signal through COMPUTER/COMPONENT 1, 2 or DVI-D *2 Items when inputting Component signal through COMPUTER/COMPONENT 1 or 2, or when selecting VIDEO or
S-VIDEO
*3 “Progressive” and “Flim Mode” can be adjusted only when 480I, 576I, 1035I or 1080I signal is input.
Page 43
-41
Useful Features
“Screen adjustment (SCR-ADJ)” menu
On Off
On Off
Main Menu Sub Menu
OSD Display
Background
Logo Blue None
Normal Full Dot By Dot Area Zoom V-Stretch Border Stretch
Center Upper Right Lower Right Upper Left Lower Left
Menu Position
Page 50
Resize
Page 49
Page 50
Page 50
Auto V-Keystone
Page 49
Page 49
Page 49
+96-96
Image Shift
V-Keystone
Page 49
+100-100
H-Keystone
SCR-ADJ
Page 49
Language
Page 50
Front Ceiling + Front Rear Ceiling + Rear
PRJ Mode
Page 50
English Deutsch Español Nederlands Français Italiano Svenska Português
polski Magyar Türkçe
+60-60
“Signal adjustment (SIG-ADJ)” menu
On Off
SIG-ADJ
+30-30
+60-60
+150-150
+150-150
Clock Phase H-Pos V-Pos Reset
Signal Info
Resolution
Main Menu
Auto Sync
Page 47
Page 47
Page 47
Page 47
Page 48
*4
*4
*5
*5
*5
Signal Type
Page 47
Page 48
*6
Auto RGB Component
Dynamic Range
*7
Auto Standard Enhanced
Auto PAL SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60
Video System
Page 48
*8
*4 Item when inputting RGB signal through COMPUTER/COMPONENT 1 or 2 *5 Item when inputting COMPUTER/COMPONENT 1 or 2 *6 Item when selecting COMPUTER/COMPONENT 1, 2 or DVI-D *7 Item when selecting DVI-D *8 Item when selecting VIDEO or S-VIDEO
Page 44
-42
“Network” menu
“Projector adjustment (PRJ-ADJ)” menu
Main Menu
Network
Page 54
On Off
IP Address Subnet Mask Gateway
Page 54
TCP/IP
Page 55
DHCP Client
Page 55
Page 55
Password
Old Password New Password Reconfirm
MAC Address
Page 55
Projector
*2
*1
*2
On Off
Normal High
LAN/RS232C
Monitor Out
RS-232C
PRJ-ADJ
Enable Disable
9600 bps 38400 bps 115200 bps
Enable Disable
Main Menu Sub Menu
Page 51
FAO VAO
Audio Out
Page 51
Page 52
Page 51
Page 51
Speaker
Page 51
Fan Mode
Page 52
All Reset
Page 53
On Off
On Off
Lamp Timer (Life)
Auto Power Off
Old Code New Code Reconfirm
Page 53
System Sound
Page 51
Page 51
System Lock
Pages 52 and 53
On Off
Auto Restart
Page 51
*1 Adjustable only when DHCP Client is set to “Off” *2 Display only
Menu Items
Page 45
-43
Useful Features
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
This operation can also be performed by using the buttons on the projector.
MENU button
MOUSE/Adjustment buttons ('/"/\/|)
RETURN button
ENTER button
Press RETURN to return to previous screen when the menu is displayed
Adjustment buttons ('/"/\/|)
MENU button
ENTER button
RETURN button
Example: “Picture” screen menu
1 Press MENU.
The “Picture” menu screen for the se­lected input mode is displayed.
2 Press
||
||
| or
\\
\\
\ and select “Pic-
ture” to adjust.
Menu item
Picture Mode
Contrast 0
0 0 0
Bright Color Tint
0Sharp
Standard
7500K 3D Progressive Auto Off Off Off
SEL./ADJ. RETURN
ENTER END
Picture SIG SCR PRJ Net.
0 0
Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode
Reset
Page 46
-44
3 Press
''
''
' or
""
""
" and select
“Bright” to adjust.
The selected item is highlighted.
To adjust the pro­jected image while watching it
Press ENTER.
The selected item (e.g. “Bright”) is dis­played by itself at the bottom of the screen.
When pressing
''
''
' or
""
""
", the following
item (“Red” after “Bright”) will be dis­played.
Note
Press ENTER again to return to the previous screen.
4 Press
\\
\\
\ or
||
||
| to adjust the item
selected.
The adjustment is stored.
5 Press MENU.
The menu screen will disappear.
Note
Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”, “FREEZE”, or “AV MUTE” functions.
0Bright
Picture
SEL./ADJ. Rtn. Menu
Rtn. Menu END
Contrast 0
15
0 0
Bright
Color Tint
0Sharp
Standard
7500K 3D Progressive Auto Off Off Off
SEL./ADJ. RETURN
ENTER END
0 0
Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode
Reset
Picture Mode
Picture SIG SCR PRJ Net.
Items to be adjusted
The item displayed by itself
Press ENTER.
Using the Menu Screen
Clock 0
0 0 0
Phase H-Pos V-Pos
Reset
Pict. SIG–ADJ SCR PRJ Net.
Contrast 0
0
0 0
Bright
Color Tint
0Sharp
Standard
7500K 3D Progressive Auto Off Off Off
SEL./ADJ. RETURN
ENTER END
0 0
Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode
Reset
Picture Mode
Picture SIG SCR PRJ Net.
Page 47
-45
Useful Features
Menu operation Page 43
11
11
1
Selecting the Picture Mode
Picture Adjustment (“Picture” menu)
“sRGB” is displayed only when RGB signal is input.
You can set or adjust each item in the “Picture”
menu to your preference. Any changes you make are retained in memory.
Note
You can also press PICTURE MODE on the remote control to select the picture mode. (See page 36.)
*sRGB is an international standard of color re­production regulated by the IEC (International Electrotechnical Commission). As the fix ed color area has been decided by the IEC, the images are displayed in a natural tint based on an origi­nal image, when “sRGB” is selected. For additional information about the sRGB func­tion, visit “http://www.srgb.com/”. You cannot set the items, “Red”, “Blue” and “CLR Temp”, when “sRGB” is selected.
• When “sRGB” is selected, the projected image may be­come dark, but this does not indicate a malfunction.
Info
Description
For standard image Brightens portions of image for more enhanced presentations. Gives natural tint to the projected image. Gives sharpness to the projected image. For high fidelity reproduc­tion of images from a computer.
Selectable items
Standard Presentation
Movie
Game
*sRGB
22
22
2
Adjusting the Image
*1
Not adjustable/selectable in the RGB input mode.
*2
Not adjustable/selectable when selecting “sRGB” in “Picture Mode”.
Note
“Red” and “Blue” cannot be set when selecting “sRGB” in “Picture Mode”.
To reset all adjustment items, select “Reset” and press ENTER.
Adjustment items
button
\\
\\
\
button
||
||
|
Contrast Bright Color
*1
Tint
*1
Sharp
*1
Red
*2
Blue
*2
For less contrast. For less brightness. For less color intensity. For making skin tones purplish. For less sharpness. For weaker red. For weaker blue.
For more contrast. For more brightness. For more color intensity. For making skin tones greenish. For more sharpness. For stronger red. For stronger blue.
Contrast 0
0 0 0
Bright Color Tint
0Sharp
Standard
7500K 3D Progressive Auto Off Off Off
SEL./ADJ. RETURN
ENTER END
0 0
Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode
Reset
Picture Mode
Picture SIG SCR PRJ Net.
1
3 4 5 6
2
7 8
The default
settings of
CLR T emp
7500K 7500K
6500K
7500K
33
33
3
Adjusting the Color Temperature
Note
Values on “CLR Temp” are only for general stan­dard purposes.
“CLR Temp” cannot be set when selecting “sRGB” in “Picture Mode”.
Selectable items 5500K 6500K 7500K 8500K 9300K 10500K
Description For lower color temperature for warmer, reddish incandescent-like images.
For higher color temperature for cooler, bluish, fluorescent-like images.
Page 48
-46
44
44
4
Selecting the Progressive Mode
55
55
5
Selecting the Film Mode
This function provides high-quality playback of images originally projected at 24 fps, such as movies on DVDs.
Description Films are detected automatically. Films are not detected.
Selectable items
Auto Off
Note
When using progressive inputs, “Film Mode” cannot be selected.
The “Film Mode” function does not work when “2D Progressive” is selected in “Progressive Mode”.
66
66
6
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Description DNR does not function. Sets the DNR level.
Selectable items
Off Level 1–3
Note
Set a level so as to view a clearer picture.
Make sure to set “DNR” to “Off” in the following cases:
When the image is blurry.
When the contours and colors of moving im-
ages drag.
When TV broadcasts with w eak signals are pro­jected.
77
77
7
Mosquito Noise Reduction (MNR)
The so-called Mosquito Noise (flickering) can be reduced.
Description MNR does not function. Sets the MNR level for viewing a clearer picture.
Selectable items
Off Level 1-3
Menu operation Page 43
Picture Adjustment (“Picture” menu)
Note
When the image is blurred or noisy, switch to the optimal mode.
When using progressive inputs, inputs are di­rectly displayed so that “2D Progressive” and “3D Progressive” cannot be selected.
Description Useful to display relatively slowmoving images such as drama and documentary more clearly. Useful to display fast-moving images such as sports and action films.
Selectable items
3D Progressive
2D Progressive
Note
You can also use ECO+QUIET on the remote control or on the projector to switch the Eco+Quiet Mode. (See page 35.)
88
88
8
Eco+Quiet Mode Setting
Brightness
Approx. 80%
100%
Selectable
items
On
Off
Fan
Sound
Low
Normal
Lamp life
Approx.
3,000 hours
Approx.
2,000 hours
Info
This function is available for all signals with VIDEO or S-VIDEO.
This function is available for 480I, 480P, 576I and 576P signals with COMPUTER1/2 or D VI.
Info
This function is available for all signals with VIDEO or S-VIDEO.
This function is available for 480I, 480P, 576I and 576P signals with COMPUTER1/2 or D VI.
Page 49
-47
Useful Features
0 0 0 0
Phase
Clock
Pict. SIG–ADJ SCR PRJ Net.
H-Pos V-Pos
Reset
Auto
640 x 480 On
Standard Auto
SEL./ADJ. RETURN
ENTER END
Resolution Auto Sync Signal Type Dynamic Range Video System
Signal Info : 800 x 600
H 60.3 kHz / V 37.8 Hz
1
3 4 5 6
2
7
Signal Adjustment (“SIG-ADJ” Menu)
11
11
1
Adjusting the Computer Image
If the optimum image cannot be obtained with Auto Sync adjustment, use the SIG-ADJ function.
Note
To reset all adjustment items, select “Reset” and press ENTER.
The adjustable range of “H-Pos” (H-Position) and “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.
Selectable items Clock Phase
H-Pos
V-Pos
Description Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right. Centers the on-screen image by moving it up or down.
22
22
2
Resolution Setting
Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. How­ever, for some signals, the optimal resolution mode in “Resolution” on the “SIG-ADJ” menu may need to be selected to match the computer display mode.
Note
See “Checking the Input Signal” on page 48 for information on the currently selected input sig­nal.
33
33
3
Auto Sync Adjustment
Used to automatically adjust a computer image.
Note
Auto Sync adjustment is also performed by pressing AUTO SYNC on the projector or on the remote control.
The Auto Sync adjustment ma y take some time to complete, depending on the image of the computer connected to the projector.
Selectable items
On
Off
Description Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer. Auto Sync adjustment is not automati­cally performed.
Menu operation Page 43
44
44
4
Signal Type Setting
This function allows you to select the input sig­nal type RGB or Component for COMPUTER/ COMPONENT 1, 2 or DVI-D.
Description Input signals are automatically recog­nized as RGB or component. Set when RGB signals are received. Set when Component signals are received.
Selectable items
Auto
RGB Component
Page 50
-48
Menu operation Page 43
77
77
7
Checking the Input Signal
This function allows you to check the current in­put signal information.
Note
The Video signal can only be set in VIDEO or S-VIDEO mode.
When “Video System” is set to “Auto”, you ma y not receive a clear picture due to signal differ­ences. Should this occur, switch to the video system of the source signal.
* When reproducing NTSC signals in PAL video
equipment.
Selectable items Auto PAL SECAM *NTSC4.43 NTSC3.58 PAL-M PAL-N PAL -60
66
66
6
Setting the Video System
The video input system mode is factory preset to “Auto”; however, a clear picture from the con­nected audio-visual equipment may not be re­ceived, depending on the Video signal difference. In that case, switch the Video signal.
Description When the black levels of the image show banding or appear faded, select the item that results in the best picture quality. (In most circumstances, “Standard” should be selected.)
Selectable items Auto Standard Enhanced
55
55
5
Selecting the Dynamic Range
An optimum picture may not be displayed if a DVI-D-capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch “Dynamic Range”.
Note
The Dynamic Range can be selected only when “DVI-D” input mode is selected.
Signal Adjustment (“SIG-ADJ” Menu)
Page 51
-49
Useful Features
Resize
0 0 0
Image Shift H-Keystone V-Keystone Auto V-Keystone
Center
On
On
Normal
Logo
Front English
SEL./ADJ. RETURN
ENTER END
OSD Display Background Menu Position PRJ Mode Language
Pict. SIG SCR-ADJ PRJ Net.
1
3
4 5 6 7 8
2
Screen Adjustment (“SCR-ADJ” Menu)
Menu operation Page 43
11
11
1
Setting the Resize Mode
Note
For details of the Resize mode, see pages 37 and 38.
You can also press RESIZE on the remote con- trol to set the resize mode. (See page 37.)
22
22
2
Adjusting the Image Position
You can move the projected image vertically.
Note
This function only works in some RESIZE modes. (See pages 37 and 38.)
To reset this function, select “0”.
||
||
| button
\ \
\ \
\ button
33
33
3
Keystone Correction
When the image is projected either from the top or from the bottom towards the screen at an angle, the image be­comes distorted trapezoidally. The function for correct­ing trapezoidal distortion is called Keystone Correction.
Auto V-Keystone Correction
Set “Auto V-Keystone” on the “SCR-ADJ” screen menu to “On”.
Manual Keystone Correction
Set “Auto V-Keystone” on the “SCR-ADJ” screen menu to “Off”. Select “V-Keystone”, and then press
\\
\\
\ or
||
||
| to parallelize the left and right sides
of the projected image with the slide bar. To parallelize the upper and lower sides, select “H­Keystone” and press
\\
\\
\ or
||
||
|.
Note
The Keystone Correction can be adjusted up to an angle of approximately ±12 degrees with “Auto V-Keystone” and up to an angle of approximately ±50 degrees with “V-Keystone” and approxi­mately ±30 degrees with “H-Keystone”.
When the screen is slanting or the image is de­teriorated, set “Auto V-Keystone” to “Off”.
Horizontal Keystone Correction
Ver tical Keystone Correction
Page 52
-50
Menu operation Page 43
Selectable items Logo Blue None
Description SHARP default image Blue screen Black screen
55
55
5
Selecting a Startup and Background Image
Description Displayed on the center of the image. Displayed on the upper right of the image. Displayed on the lower right of the image. Displayed on the upper left of the image. Displayed on the lower left of the image.
Selectable items Center Upper Right Lower Right Upper Left Lower Left
66
66
6
Selecting the Menu Screen Position
Select “Menu Position” on the “SCR-ADJ” menu and the desired position for the menu screen.
77
77
7
Reversing/Inverting Pro­jected Images
This projector is equipped with a reverse/invert image function that allows you to reverse or in­vert the projected image for various applications.
Note
This function is used for the reversed image and ceiling-mount setups. (See page 19.)
Description
Normal image (Projected from the front of the screen)
Inverted image (Projected from the front of the screen with an inverted projector)
Reversed image (Projected from the rear of the screen or with a mirror)
Reversed and inverted image (Pro­jected with a mirror)
Selectable items Front
Ceiling + Front
Rear
Ceiling + Rear
88
88
8
Selecting the On-screen
Display Language
The projector can switch the on-screen display language among 17 languages.
Screen Adjustment (“SCR-ADJ” Menu)
Description
All On-screen Displays are displayed. INPUT/VOLUME/AV MUTE/FREEZE/
AUTO SYNC/MAGNIFY/ “An invalid button has been pressed.” are not displayed.
Selectable items On Off
44
44
4
Setting the On-screen Display
This function allows you to turn the on-screen messages on or off.
Page 53
-51
Useful Features
Auto Power Off Auto Restart System Sound Speaker Audio Out
9600bps
Enable
On
On
On FAO
On
Enable
Normal Disable
SEL./ADJ. RETURN
ENTER END
Monitor Out LAN/RS232C RS-232C Fan Mode System Lock
All reset
Lamp Timer (Life) [ 0]h [ 0] min ( 100%)
Pict. SIG SCR PRJ-ADJ Net.
1 2 3 4 5 6 7 8 9 0 q
w
Menu operation Page 43
Description The projector automatically enters the standby mode when no input signal is detected for 15 minutes or longer. The Auto Power Off function will be disabled.
Selectable items On
Off
11
11
1
Auto Power Off Function
Note
When the Auto P ower Off function is set to “On”, 5 minutes before the projector enters the standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.
Description If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. The projector does not turn on auto­matically when the power cord is plugged into the AC outlet or the breaker switch is turned on.
Selectable items On
Off
22
22
2 Auto Restart Function
Description
A confirmation sound is made when the projector turns on/off. No confirmation sound is made.
Selectable items On
Off
33
33
3
Setting the Confirmation Sound (System Sound)
Helpful Functions Set during Installation (“PRJ-ADJ” menu)
44
44
4
Speaker Setting
This function allows you to set the audio output of the internal speaker to “On” or “Off” such as when the projector is connected to an external amplifier.
Selectable items
On
Off
Description The audio signal is output from the internal speaker. The audio signal is not output from the internal speaker.
55
55
5
Audio Output Type Setting
This function determines whether the audio level output from the AUDIO output (MONITOR output) terminal is fixed or variable by linking with VOL­UME.
Info
When “Audio Out” has been set to “V A O”, first make sure to lower the volume of the projector before turning the power on or off and when switching the input.
Description Audio output that does not vary in strength with the volume level of the source projector. Audio output that varies in strength with the volume level of the source projector.
Selectable items FAO (Fixed Audio Output) VAO (Variable Audio Output)
66
66
6
Monitor Output
77
77
7
LAN/RS232C
When set to “Enable”, the function is activated and power is consumed even in the standby mode. It is recommended that the function be set to “Dis­able” when it is not connected. This reduces power consumption when the projector is in the standby mode.
Description The function is activated even if the projector is in standby mode. The function is switched off when the projector is in standby mode.
Selectable items Enable
Disable
Note
When you want to control the projector using the LAN/RS232C function, select “Enable”.
Page 54
-52
Helpful Functions Set during Installation (“PRJ-ADJ” menu)
Menu operation Page 43
Setting/Changing the keycode
1 Select “System Lock”, then press
ENTER or
||
||
|.
2 Select “Next”, then press ENTER.
The screen for entering the keycode appears.
3 Press the 4 buttons on the remote
control or on the projector to enter the preset keycode in “Old Code”.
When setting the keycode for the first time, press " on the projector for four times.
Note
If you input a wrong keycode, the cursor returns to the first point of the “Old Code”.
The preset keycode is 4 " buttons on the projector. When you press the " button four times, the keycord input screen disappears.
4 Press the 4 buttons on the remote
control or on the projector to enter the new keycode in “New Code”.
Note
You cannot use the following buttons for keycode: STANDBY/ON, ON, STANDBY,
ENTER, L-CLICK, R-CLICK/RETURN, MENU, ECO+QUIET and BREAK TIMER
System lock function recognizes each
button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in set­ting your keycode, the keycode cannot be canceled with the remote control.
Setting the System Lock
Old Code
New Code Reconfirm
––––
–––– ––––
PRJ-ADJ
PRJ-ADJ
Setting the System Lock
Old Code
New Code
Reconfirm
****
–––
––––
88
88
8
Selecting the Transmis­sion Speed (RS-232C)
Make sure that both the projector and computer are set for the same baud rate.
Description
Transmission speed is slow.
Transmission speed is rapid.
Selectable items 9600 bps
38400 bps 115200 bps
Note
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for RS-232C Specifica­tions and Command Settings.
Refer to the computer’s operation manual for instructions for setting the computer’s baud r ate.
99
99
9
Fan Mode Setting
This function changes the fan rotation speed.
Description Suitable for normal environments. Select this when using the projector at altitudes of approximately 1,500 meters (4,900 feet) or more.
Selectable items Normal High
When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.
00
00
0
System Lock Function
This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the pro­jector is turned on. We suggest you record the
keycode in a safe place where only autho­rized users have access.
Info
If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Ser­vice Center (see page 68). Even if the product warranty is valid, the keycode reset will incur a charge.
Page 55
-53
Useful Features
Menu operation
Page 43
5
Enter the same keycode in “Reconfirm”.
Note
To cancel the keycode that you have al­ready set
Press " on the projector for four times in steps 4 and 5 above.
When the System Lock is set
When System Lock is set, the keycode input screen appears after the power is turned on. When it ap­pears, enter the right keycode to start projection.
Input screen for keycode
Info
Keylock cannot be set while the projector is: dis­playing the “Menu” screens, in standby mode, warming up, changing input signals, operating “Auto Sync” function or on the “System Lock” screen during warming up.
System Lock
––––
Keylock Function
Locking the Operation Buttons on the Projector
Use this function to lock the operation but­tons on the projector.
Locking the Operation Buttons
Hold down ENTER on the projector for about 5 sec­onds while the projector is being turned on.
On-screen Display
Keylock function ON
The keylock function does not affect the operation with the remote control buttons.
You cannot use the keylock function while the pro­jector is warming up.
Taking the Keylock off
Hold down ENTER on the projector for about 5 seconds.
On-screen Display
Keylock function OFF
When the projector is in standby mode, you can release the keylock by holding down ENTER and STANDBY/ON on the projector simultaneously f or about 5 seconds.
qq
qq
q
Returning to the Default
Settings
This function allows you to initialize the settings you have made in the projector.
Note
The following items or menu cannot be initialized.
“SIG-ADJ” menu Resolution
“SCR-ADJ” menu Language
“PRJ-ADJ” menu Lamp Timer (Life) System Lock
ww
ww
w Checking the Lamp Life
Status
You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).
Note
It is recommended that the lamp be changed when the remaining lamp life becomes 5%.
Remaining lamp life changes within the range of the values shown depending on the frequency at which “Eco+Quiet Mode” is switched to “On”
and “Off”. (See page 46.)
The lamp life may vary depending on the us­age condition.
Lamp usage condition
“Life” Operated exclusively while “Eco+Quiet Mode” is “On”. Operated exclusively while “Eco+Quiet Mode” is “Off”.
Remaining lamp life
100% 5%
Approx. Approx. 3,000 hours 150 hours
Approx. Approx.
2,000 hours 100 hours
Page 56
-54
Setting up the Projector Network Environment (“Network” menu)
11
11
1
Setting a Password
If you do not want others to change the setting for the “Network” menu, set a password.
Setting a Password
1 Select “Password”, then press
||
||
|.
The screen for entering the password ap­pears.
2 Press
''
''
' or
""
""
" to set the first digit in
“New Password”, then press
||
||
|.
3 Enter the remaining 3 digits, then
press ENTER.
To return to the previous digit, press \.
4 Enter the same password in
“Reconfirm”, then press ENTER.
The status for “Password” changes to “En­able”.
Note
Once after the password is set, you must enter the password to change the “Network” menu settings.
Changing the Password
1 Select “Password”, then press
||
||
|.
The screen for entering the password ap­pears.
2 Enter the password in “Old Pass-
word” using
''
''
',
""
""
",
||
||
| and
\\
\\
\, then
press ENTER.
3 Enter the password in “New Pass-
word” using
''
''
',
""
""
",
||
||
| and
\\
\\
\, then
press ENTER.
4 Enter the same password again in
“Reconfirm” using
''
''
',
""
""
",
||
||
| and
\\
\\
\,
then press ENTER.
Note
If you do not need the password protection for the “Network” menu settings anymore, press ENTER without entering new password in steps 3 and 4.
•To cancel the pass word settings, press RETURN.
If you forget the password
If you forget the password, perform the following procedure to delete it, then set a new password.
On the projector, press
Note
If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page 53.)
You cannot use the buttons on the remote control to delete the password.
Menu operation Page 43
Password
DHCP Client
TCP/IP
Off
Disable
SEL./ADJ. RETURN
ENTER END
MAC Address XX:XX:XX:XX:XX:XX
Projector XX-XXXX
Pict. SIG SCR PRJ Network
1
3
4
2
Setting the Password
Old Password
New Password
Reconfirm
–––
–––
––––
Network
Page 57
-55
Useful Features
22
22
2
DHCP Client Setting
Connect the LAN cable before turning the pro­jector on. If not, the DHCP Client function does not work.
Select “On” for “DHCP Client”. “Obtaining IP Address...” appears, then the menu screen appears. Confirm the parameters of IP Address, Subnet Mask and Gateway on the TCP/IP screen. If the DHCP server is not available, “Could not obtain IP Address.” appears. In this case, set the TCP/IP manually . (See the item
3.)
33
33
3
TCP/IP Setting
Set the TCP/IP manually.
1 Select “Off” for “DHCP Client”, then
press ENTER.
2 Select “TCP/IP”, then press ENTER.
3 Enter “IP Address” using
''
''
',
""
""
",
||
||
|
and \, then press ENTER.
4 Enter “Subnet Mask” using
''
''
',
""
""
",
||
||
| and \, then press ENTER.
5 Enter “Gateway” using
''
''
',
""
""
",
||
||
| and
\, then press ENTER.
Selectable items On
Off
Description Obtains configuration parameters for TCP/IP network automatically. Sets the TCP/IP manually.
Setting the TCP/IP
Subnet Mask
IP Address
Gateway
1
55.2
92.
000.
1
55.2
68.
000.
1
55.2
50.
000.
0
000
02
000
Network
Menu operation Page 43
Selectable items IP Address
Subnet Mask
Gateway
Description
Factory default setting:
192.168.150.002 Enter an IP address appropriate for the network. Factory default setting:
255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network. Factory default setting: 000. 000. 000. 000 * When not in use, set to “000. 000.
000. 000”.
Note
Confirm the existing network’s segment (IP ad­dress group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If “192.168.150.002” is not used in a network with an IP address of “192.168.150.XXX”, you don’t have to change the projector IP address.
For details about each setting, consult your network administrator.
44
44
4 Confirming the
Projector Information
You can confirm the MAC address and projector name.
Displayed items
MAC Address
Projector
Description The MAC address of the projector is displayed. The projector name is displayed.
Note
For information on how to change the projector name, see “SETUP MANUAL” contained in the supplied CD-ROM.
Page 58
-56
Cleaning the lens
Use a commercially available blower or lens clean­ing paper (for glasses and camera lenses) for clean­ing the lens. Do not use any liquid type cleaning agents, as they may w ear off the coating film on the surface of the lens.
As the surface of the lens can easily get damaged, be careful not to scrape or hit the lens.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the ex­haust vent and the intake vent.
Info
If you want to clean the air v ents during projec­tor operation, ensure you press STANDBY/ON on the projector or STANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, unplug the power cord from the AC socket and clean the vents.
• The air filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky loca­tion.
Cleaning the projector
Ensure the power cord is unplugged before cleaning the projector.
The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner , as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projec­tor for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Wipe off dirt gently with a soft flannel cloth.
When the dirt is hard to remove, soak a cloth in a
mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projec­tor before use.
Maintenance
Cleaning
Paper
Mild detergent
diluted with water
Mild detergent
Wax
Thinner
Page 59
-57
Appendix
Replacing the Air Filter
• This projector is equipped with air filters
to ensure the optimal operating condition of the projector.
• Ask your nearest Sharp Authorized Pro-
jector Dealer or Service Center to ex­change the filter (PFILDA022WJKZ) when it is no longer possible to clean.
Replacing the Air Filter
1 Press STANDBY/ON on the pro-
jector or STANDBY on the remote control to put the projector into the standby mode.
Wait until the cooling fan stops.
2 Disconnect the power cord.
Unplug the power cord from the AC socket.
3 Remove the filter cover.
Turn over the projector. Pull down the car­rying handle (1), grab the tab (2) and slide open the filter cover (3).
4 Remove the air filter.
Pick the air filter up with your fingers and lift it out of the filter cover.
STANDBY button
AC socket
Tab
2
1
3
STANDBY/ON button
Page 60
-58
5 Place a replacement air filter.
Place the new air filter onto the filter cover.
6 Replace the filter cover.
Slide the filter cover in the direction of the arrow to close it.
Note
Ensure the filter cov er is securely installed. The power will not turn on unless it is correctly in­stalled.
Replacing the Air Filter
Page 61
-59
Appendix
Power indicator Lamp indicator Temperature warning indicator
Maintenance Indicators
Maintenance Indicators
The warning lights on the projector indicate problems inside the projector.
If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and
the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, “ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and then the projector will enter the standby mode. After “
” appears, ensure you perform the measures
described on page 60.
About the lamp indicator
When the remaining lamp life becomes 5% or less, “ ” (yellow) and “Change The Lamp.” will be displayed on the screen. When the percentage becomes 0%, it will change to “
” (red), the lamp will automatically turn off and then the projector will automatically enter the standby mode. At this time, the lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
Page 62
-60
Maintenance indicator
Problem
Cause Possible solution
Temperature
warning
indicator
Normal
Abnormal
Off
Red on (Standby)
The internal temperature is abnormally high.
Abnormal
Blocked air intake
Relocate the projector to an area
with proper ventilation (see page
8).
Cooling fan break­down
Internal circuit failure
Clogged air intake
Take the projector to your nearest
Sharp Authorized Projector Dealer or Service Center (see page 68) for repair.
Clean the exhaust and intake vents. (See page 56.)
Lamp
indicator
Red on (Standby)
The lamp does not illuminate.
Burnt-out lamp
Lamp circuit failure
Carefully replace the lamp. (See
page 62.)
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 68) for repair.
Please exercise care when replacing the lamp.
Securely install the lamp unit cover.
Red on
Time to change the lamp.
Remaining lamp life becomes 5% or less.
Green on
Green blinks
when the lamp
is warming up
Info
If the temperature warning indicator illuminates and the projector enters the standby mode, check whether any of the ventilation holes are bloc ked (see page 8) and then try turning the power back on. W ait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
The lamp does not illuminate.
The lamp is shut down abnormally.
Disconnect the power cord from the AC outlet, and then connect it again.
Power
indicator
Green on/
Red on
Green blinks
(Cooling)
Red blinks
The power indicator blinks in red when the projector is on.
If the power indicator blinks even when the covers are securely installed, or if the cooling fan does not run normally, then contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 68) for advice.
The filter cover, lamp unit cover or lens housing cover is open.
Cooling fan break­down
Maintenance Indicators
Page 63
-61
Appendix
Lamp
It is recommended that the lamp unit (optional: AN-C430LP) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 53.
Purchase a replacement lamp unit of type AN-C430LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho­rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP
Caution Concerning the Lamp
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.
Replacing the Lamp
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn
or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.
Carefully change the lamp by following the instructions described in this section. *If you wish, you
may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
* If the new lamp does not illuminate after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
Regarding the Lamp
U.S.A. ONLY
Page 64
-62
Regarding the Lamp
Securing screws
Optional
accessory
Lamp unit AN-C430LP
Removing and Installing the Lamp Unit
Warning!
Do not remove the lamp unit from the pro­jector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.
Info
Do not touch the glass surface of the lamp unit or the inside of the projector.
To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.
Do not loosen other screws except for the lamp unit cover and lamp unit.
1 Press STANDBY/ON on the
projector or STANDBY on the remote control to put the projec­tor into standby mode.
Wait until the cooling fan stops.
2 Disconnect the power cord.
Unplug the power cord from the AC socket.
Leave the lamp until it has fully cooled down (about 1 hour).
3 Remove the lamp unit cover.
Loosen the user service screw (1) that secures the lamp unit cover . Slide do wn (2) and remove the lamp unit cover (3).
4 Remove the lamp unit.
Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow . At this time, keep the lamp unit horizontal and do not tilt it.
AC socket
1
3
2
User service screw (for lamp unit cover)
STANDBY/ON button
Page 65
-63
Appendix
User service screw (for lamp unit cover)
AC socket
5 Insert the new lamp unit.
Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.
6 Replace the lamp unit cover.
Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit cover.
Info
If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.
You can also reset the lamp timer via the LAN. (Refer to the SETUP MANU AL on the sup­plied CD-ROM for details.)
1 Connect the power cord.
Plug the power cord into the AC socket of the projector.
2 Reset the lamp timer.
While simultaneously holding down ", ENTER and MENU on the projector, press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green.
“LAMP 0000H” is displayed, indicating that the lamp timer is reset.
" button
ENTER button
STANDBY/ON button
Lamp indicator
MENU button
Page 66
-64
Storing the Projector
Lens cap
Fixing band
Info
How to Use the Storage Case
When storing the projector, attach the lens cap to the lens, and place it in the supplied storage case.
1 Open the cover of the storage
case.
2 Place the projector into the stor-
age case.
Ensure the projector has cooled down sufficiently before placing it in the case.
Ensure the lens cap is attached to the lens for protection.
Place the projector into the storage
case with the lens facing the handle.
Ensure the projector is held in place by using the fixing band.
3 Close the cover of the storage
case.
4 Place the accessories in the front
pocket of the storage case.
Supplied accessories (Remote control, etc.)
Page 67
-65
Appendix
Note
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual.
When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.
When projecting the RGB interlace signal using COMPUTER/COMPONENT 1, 2 or D VI-D with “Signal Type”
set to “Auto” or “RGB”, the image may not be projected as desired. In this case, use either Video or S-Video.
When “Screen resolution” of the computer is different from the resolution displayed on the projected image, follow the procedures sho wn belo w.
- Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in “Screen
resolution” of the computer.
- Depending on the computer you are using, the output signal may not be faithful to the “Screen resolu-
tion” adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is recommended that the resolution be set to “1024 × 768”.
Computer Compatibility Chart
Multiple signal support Horizontal Frequency: 15–70 kHz Vertical Frequency: 43–85 Hz
DTV
Computer
Pixel Clock: 12–108 MHz Sync signal: Compatible with TTL level
Compatible with sync on green signal
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
62.8
47.7
47.8
55.0
66.2
67.5
64.0
64.0
34.9
49.7
60.2
68.7
60 70 85 60 70 85 50 60 70 72 75 85 50 56 60 70 72 75 85 50 60 70 75 85 60 60 75 60 60 60 70 75 60 60 67 75 75 75
Upscale
True
True
Intelligent Compression
Upscale
Intelligent Compression
640 × 400
720 × 400
640 × 480
800 × 600
1,024 × 768
1,280 × 720 1,280 × 768 1,280 × 800 1,360 × 768 1,366 × 768
1,152 × 864
1,280 × 1,024 1,400 × 1,050
640 × 480
832 × 624 1,024 × 768 1,152 × 870
MAC 13" MAC 16" MAC 19" MAC 21"
PC
VGA
SVGA
XGA
WXGA
SXGA
SXGA+
VGA
SVGA
XGA
SXGA
✔ ✔ ✔
✔ ✔
✔ ✔ ✔
✔ ✔ ✔ ✔
✔ ✔ ✔
✔ ✔
Display
PC/MAC Resolution VESA Standard
Vertical Frequency
(Hz)
DVI
Support
Horizontal Frequency
(kHz)
15.7
31.5
33.8
15.6
31.3
37.5
45.0
33.8
28.1
33.8
480
I
480P 540P
576
I
576P 720P 720P
1035
I
1080
I
1080
I
60 60 60 50 50 50 60 60 50 60
Signal Vertical Frequency (Hz) DVI SupportHorizontal Frequency (kHz)
✔ ✔
✔ ✔ ✔
✔ ✔
The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
Page 68
-66
Troubleshooting
Check
Projector power cord is not plugged into the wall outlet.
Power to the external connected devices is off.
The selected input mode is wrong.
The AV MUTE function is working.
Cables incorrectly connected to the rear panel of the projector.
Remote control batteries have run out.
External output has not been set when connecting notebook computer.
The filter cover, lamp unit cover or lamp housing cover is not installed correctly.
If the connected DVI digital equipment is turned on before the “DVI-D” input mode is selected on the projector, the image may not be projected properly or may not be displayed at all. Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.
Cables incorrectly connected to the rear panel of the projector.
“Bright” is set to minimum position.
Depending on the computer you are using, an image may not
be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer’s operation manual for how to switch its signal output settings.
Image adjustments are incorrectly set.
(Video, S-Video Input only)
Video input system is incorrectly set.
(COMPUTER/COMPONENT 1, 2, DVI-D only)
Input signal type (RGB/Component) is incorrectly set.
Adjust the focus.
The projection distance exceeds the focus range.
There is fog on the lens. If the projector is carried from a cold
room into a warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Please set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.
(Computer Input only)
Perform “SIG-ADJ” Adjustments. (“Clock” Adjustment)
Perform “SIG-ADJ” Adjustments. (“Phase” Adjustment)
Noise may appear depending on the computer.
Cables incorrectly connected to the rear panel of the projector.
Volume is set to minimum.
When the projector is connected to an external device and the
volume is set to minimum, the sound is not output even if you turn up the volume of the external device.
“Speaker” is set to “Off”.
Make the necessary adjustments of each item in the “SIG-ADJ”
menu.
Depending on the computer you are using, the output resolution signal may be different from the one you have set. For details, refer to the operation manual of the computer.
Problem
Data image is not
centered.
Page
30
34 34
23-29
15 23 60
24
23-29
45
45
48 47
33 19
47 47
23-29
34
51
47
No picture and no sound
or projector does not start.
Color is faded or poor.
Picture is blurred;
noise appears.
Sound is heard but no
picture appears.
Picture appears but no
sound is heard.
Page 69
-67
Appendix
CheckProblem Page
An unusual sound is
occasionally heard
from the cabinet.
Maintenance
indicator illuminates or
blinks in red.
The projector cannot be turned on or put into the standby mode using the
STANDBY/ON button on
the projector.
Picture is green with
component input signals
(COMPUTER/
COMPONENT 1, 2, DVI-D)
.
Picture is pink (no green)
with RGB input signals
(COMPUTER/
COMPONENT 1, 2, DVI-D)
.
Picture is too bright and
whitish.
The black levels of the
image show banding or
appear faded when DVI-
D is selected.
The cooling fan becomes noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp takes a long
time to turn on. Picture is dark.
The remote control
cannot be used.
If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.
See “Maintenance Indicators”.
The keylock is set.
If the keylock is set to ON, all the buttons are locked.
Change the input signal type setting.
Image adjustments are incorrectly set.
Select the Dynamic Range setting (“Standard” or “Enhanced”)
that results in the best picture quality.
When temperature inside the projector increases, the cooling fan runs faster.
The lamp indicator is illuminating in red. Replace the lamp.
Cables incorrectly connected to the projector or the connected equipment works improperly.
If this happens frequently, replace the lamp.
The lamp will eventually need to be changed.
The lamp has reached the end of its life. Replace the lamp.
Operate the remote control while pointing it at the projector’s remote control sensor.
The remote control may be too far away from the projector.
If direct sunlight or a strong fluorescent light is shining on the
projector’s remote control sensor, place the projector where it will not be affected by strong light.
The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.
59
53
47
45
48
59
23-29
62 62
15
15
This projector is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the projector and plug it in again after more than 5 minutes.
Page 70
-68
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 66 and 67. If this operation manual does not answer your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140 http://www.sharp.ca
Mexico Sharp Electronics Corporation Mexico
Branch
(525) 716-9000 http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin American
Group
(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com
Germany Sharp Electronics (Europe) GMBH
01805-234675 http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
08705 274277 http://www.sharp.co.uk/customersupport
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1 http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr
Spain Sharp Electronica Espana, S.A.
93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se
Austria Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at
Benelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723) Nederland 9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu
Australia Sharp Corporation of Australia
Pty. Ltd.
1300-135-022 http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111 Fax: (09) 573-0112 http://www.sharp.net.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk
Taiwan Sharp Corporation (Taiwan)
0800-025111 http://www.sharp-scot.com.tw
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311 helpdesk@smef.global.sharp.co.jp
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002 lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr
India Sharp Business Systems (India)
Limited
(91) 11- 6431313 service@sharp-oa.com
Page 71
-69
Appendix
Specifications
As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
Model Display devices Resolution Lens
Input terminals
Output terminals
Control and communication terminals
Speakers Projection lamp Rated voltage Rated frequency Input current Power consumption (Standby)
Operation temperature Cabinet Dimensions (main body only) [W × H × D]
Weight (approx.)
F number Zoom Focus DVI-D (Compatible with HDCP) Computer/Component
(mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) Computer/Component
(mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) LAN (RJ-45) USB (Type B) RS-232C (mini DIN 9 pin) Wired Remote
(ø3.5 mm stereo minijack)
XG-C465X-L/XG-C435X-L
0.8" LCD panel × 3 XGA (1024 × 768) F 1.7 – 1.9 Manual, ×1.2 (f = 28.0 – 33.6 mm) Manual
×1 ×2
×1 ×1 ×2 ×2 (L/R) ×1
×1 (variable audio output) ×1 ×1 ×1 ×1
2 W (Mono) 275 W AC 100 – 240 V 50/60 Hz
3.6 A 360 W (10.9 W) with AC 100 V
345 W (12.5 W) with AC 240 V 41°F to 95°F (+5°C to +35°C) Plastic 12
27
/32" × 4" × 11 1/64"
(326 × 101.5 × 279.5 mm)
10.8 lbs. (4.9 kg)
Page 72
-70
2D Progressive .........................................................46
3D Progressive .........................................................46
AC socket .................................................................30
Adjustment buttons...................................................43
All Reset ...................................................................53
Area Zoom ................................................................ 38
Aspect ratio.........................................................37, 38
AUDIO input terminal ......................................... 23-26
Audio Output.............................................................51
AUDIO output terminal .............................................29
Auto V-Keystone .................................................32, 49
Auto Power Off .........................................................51
Auto Restart..............................................................51
Auto Sync (Auto Sync adjustment) .......................... 47
AUTO SYNC button.................................................. 35
AV MUTE button.......................................................34
Background...............................................................50
Blue...........................................................................45
Border .......................................................................37
Bright ........................................................................45
Clock .........................................................................47
CLR Temp (Color T emperature) ............................... 45
Color .........................................................................45
COMPUTER/COMPONENT 1 input terminal ....23, 25
COMPUTER/COMPONENT 2 input terminal ....23, 25
Contrast ....................................................................45
DHCP Client .............................................................55
DIN-D-sub RS-232C adaptor ................................... 27
DNR ..........................................................................46
Dot By Dot ................................................................37
Dynamic Range ........................................................48
DVI-D input terminal ...........................................24, 25
ECO+QUIET button..................................................35
Eco+Quiet Mode.......................................................46
ENTER button...........................................................44
Exhaust vent .......................................................13, 56
Fan Mode.................................................................. 52
Film Mode ................................................................. 46
FREEZE button ........................................................35
Full ............................................................................37
Game ........................................................................45
Gateway....................................................................55
Height Adjustment button .........................................31
H-Pos ........................................................................47
Image Shift................................................................49
INPUT buttons ..........................................................34
Intake vent ..........................................................13, 56
IP Address ................................................................55
Kensington Security Standard connector ................13
Keycode....................................................................52
Keylock ..................................................................... 53
KEYSTONE button...................................................32
Keystone Correction ...........................................32, 49
Lamp .........................................................................61
Lamp indicator ....................................................30, 59
Lamp Timer (Life) .....................................................53
LAN terminal .............................................................28
Language (on-screen display language)..................50
LAN/RS232C ............................................................51
L-CLICK button.........................................................39
Lens cap ...................................................................12
Lens cap strap ..........................................................10
MAC Address............................................................ 55
MAGNIFY buttons ....................................................36
MENU button ............................................................43
Menu Position ...........................................................50
MNR..........................................................................46
Monitor Output..........................................................51
MONITOR output terminal........................................28
MOUSE/Adjustment buttons ..............................39, 43
Movie ........................................................................45
Network...............................................................42, 54
Normal ................................................................37, 38
ON button .................................................................30
Optional accessories ................................................10
OSD Display .............................................................50
PAGE Up/Down buttons ........................................... 39
Password ..................................................................54
PDF.............................................................................6
Phase........................................................................47
Picture.................................................................40, 45
Picture Mode.............................................................45
PICTURE MODE button ...........................................36
Power cord................................................................30
Power indicator...................................................30, 59
Presentation..............................................................45
PRJ-ADJ .............................................................42, 51
PRJ mode .................................................................50
Progressive...............................................................46
Projector ...................................................................55
R-CLICK/RETURN button ..................................39, 43
Red ...........................................................................45
Remote control ......................................................... 14
Remote control sensor .............................................15
Remote receiver .......................................................39
Replacing the lamp...................................................61
Reset.........................................................................45
Resize .......................................................................49
RESIZE button..........................................................37
Resolution.................................................................47
RGB cable ................................................................23
RS-232C ...................................................................52
RS-232C terminal ..................................................... 27
SCR-ADJ ............................................................41, 49
Sharp ........................................................................45
SIG-ADJ..............................................................41, 47
Signal Info.................................................................48
Signal Type ............................................................... 47
Speaker ....................................................................51
sRGB ........................................................................45
Standard ...................................................................45
STANDBY button ......................................................30
Storage case.............................................................64
Stretch ................................................................37, 38
Subnet Mask.............................................................55
Supplied accessories ...............................................10
S-VIDEO input terminal ............................................ 26
System Lock .............................................................52
System Sound ..........................................................51
TCP/IP ......................................................................55
Temperature warning indicator.................................59
Tilt dial.......................................................................31
Tint ............................................................................45
USB terminal.............................................................39
VIDEO input terminal................................................26
Video System............................................................48
Volume buttons .........................................................34
V-Pos ........................................................................47
V-Stretch...................................................................38
WIRED REMOTE terminal .......................................14
Index
Page 73
SHARP CORPORATION
Loading...