Sharp NOTEVISION PG-M20X User Manual

OPERATION MANUAL
MODEL
PG-M20X
Introduction
Setup and Connections
Basic Operation
DIGITAL MULTIMEDIA PROJECTOR
Appendix
IMPORTANT
For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 14.
This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC.
Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG.
Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.
Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.
Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.
Model No.: PG-M20X
Serial No.:
εγκατάσταση αυτή αντα οκρίνεται στις α αιτήσεις των οδηγιών της ∂ υρω αϊκής ∂ νωσης 89/336/ ∂√∫ και 73/23/∂√∫ ,  ως οι κανονισµοί αυτοί συµ ληρώθηκαν α  την οδηγία 93/68/∂√∫ .
Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.
Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som kompletteras av 93/68/ EEC.
Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.
Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/EEC.
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live As the colours of the wires in the mains lead of this product may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug. Before replacing the plug cover make sure that:
If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
or and of the same rating as
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (Traditional Chinese and Simplified Chinese), Korean and Arabic. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Schwedisch, Spanisch, Italienisch, Niederländisch, Portugiesisch, Chinese (Traditionelles Chinesisch und einfaches Chinesisch), Koreanisch und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, suédois, espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et chinois simplifié), coréen et arabe. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska (traditionell kinesiska och förenklad kinesiska), koreanska och arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, sueco, español, italiano, holandés, portugués, chino (chino tradicional y chino simplificado), coreano y árabe. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, svedese, spagnolo, italiano, olandese, portoghese, cinese (cinese tradizionale e cinese semplificato), coreano e arabo. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds, Spaans, Italiaans, Nederlands, Portugees, Chinees (Traditioneel Chinees en Vereenvoudigd Chinees), Koreaans en Arabisch. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Sueco, Espanhol, Italiano, Holandês, Português, Chinês, Chinês (Tradicional e Chinês Simplificado), Coreano e Árabe. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING:
See bottom of actual set.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
The lightning flash with arrowhead symbol,
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREWS.
DO NOT REMOVE COVER.
PERSONNEL.
within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Introduction
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip­ment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
-1
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the POWER button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning the Lamp Replacement
See Replacing the Lamp” on page 71.
LAMP REPLACEMENT CAUTION
BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-PGM20X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS
PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.
PRECAUTIONS A OBSERVER LORS DU REMPLACEMENT DE LA LAMPE.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE
AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-PGM20X//1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
-2

Outstanding Features

1. Image Quality
Superior image quality with Fujinon™ optical lens system
Newly developed DDR (Double Data Rate) chip eliminates Color Break-
ing phenomena common with previous generation DLP™ projectors.
Newly developed 12° DMD™ chip provides significantly improved opti-
cal efficiency and excellent contrast ratio.
2. Light, Compact, and Unique Slim Design
A new optical engine creates a unique slim design and compact size (4.2 liters, 5.8 lbs. (2.6 kg)).
3. Superior PC Compatibility
Supports a refresh rate (vertical frequency) of up to 200 Hz and a wide range of synchronous signals.
Using Advanced Intelligent Compression Technology, computer screens of UXGA (1,600 # 1,200) resolution can be displayed with minimal dis­tortion.
Introduction
4. Advanced Computer & Video lntegrated Composer Technology
Realizes vivid images using the latest high image quality circuitry.
New I/P conversion algorithm enhances the performance of the motion detect I/P
conversion.
Extensive improvements on the jagged edges or slanted lines in moving images.
Contrast Control Dynamic Gamma
Improved contrast and natural color gradation by minimizing hue change.
Color Management Function
Supports sRGB (color management).
Noise Reduction
Allows for a clear image even with noisy source signals.
New Edge Up-Scaling
Reduces jaggies and flickering when up-scaling edges of slanted lines, enabling sharper quality images.
-3

Contents

Introduction
Outstanding Features ......................................... 3
Contents............................................................... 4
IMPORTANT SAFEGUARDS ............................... 6
How to Access the PDF Operation Manuals..... 9
Part Names ........................................................ 10
Projector (Front and Top View) ................................10
Projector (Side View) .............................................. 11
Remote Control ....................................................... 12
Using the Remote Control ................................ 13
Available Range of the Remote Control ................. 13
Inserting the Batteries .............................................13
Accessories ....................................................... 14
Setup and Connections
Setup .................................................................. 16
Using the Adjustment Feet ..................................... 16
Setting up the Screen ..............................................17
Screen Size and Projection Distance ......................18
Projecting a Reversed/Inverted Image ................... 19
Connecting the Projector to Other Devices.... 20
Before Connecting.................................................. 20
This projector can be connected to: .......................20
Connecting the Power Cord ................................... 20
Connecting the Projector to a Computer .......... 21
Connecting to Video Equipment ....................... 23
Connecting to a Monitor ................................... 25
Using the Wireless Presentation Function
of the Remote Control ................................ 26
Basic Operation
Setting with the Buttons
Image Projection ............................................... 28
Basic Procedure ......................................................28
Selecting the On-screen Display Language ...........30
Adjusting the Lens .................................................. 31
Correcting the Trapezoidal Distortion
(Keystone Correction)................................. 32
Setting with the Menus
Menu Bar Items ................................................. 34
Using the Menu Screen .................................... 36
Basic Operations (Adjustments) ............................ 36
Basic Operations (Settings).....................................38
Adjusting the Picture ........................................ 40
Adjusting Image Preferences ..................................40
Selecting the Signal Type ....................................... 40
Progressive Mode....................................................41
Adjusting Computer Images ............................ 42
When Auto Sync is OFF...........................................42
Saving Adjustment Settings.....................................42
Selecting Adjustment Settings ................................43
Special Mode settings .............................................43
Checking the Input Signal .......................................43
Auto Sync Adjustment .............................................44
Auto Sync Display Function ................................... 44
Easy to Use Functions
Selecting the Picture Display Mode ................ 46
Displaying a Still Image .................................... 48
Enlarging a Specific Portion of an Image ....... 49
Gamma Correction Function............................ 50
Displaying Dual Pictures (Pict in Pict) ............ 51
Selecting the Power Save Mode ...................... 52
Setting the Power Save Mode .................................52
Automatic Power Shutoff Function.......................... 52
Activating the sRGB Color Management
Function ....................................................... 53
Auto Search Function ....................................... 53
Video Digital Noise Reduction (DNR) System ...
Setting the On-screen Display ......................... 54
Setting the Video Signal ................................... 55
Saving Projected Images.................................. 56
Capturing the Image .............................................. 56
Deleting the Captured Image ..................................56
Setting a Background Image............................ 57
Selecting a Startup Image ................................ 57
Using an RGB Monitor Loop-out Adaptor ...... 58
Displaying the Lamp Usage Time .................... 58
Displaying the Break Timer .............................. 59
Reversing/Inverting Projected Images ............ 60
Locking the Operation
Buttons on the Projector ............................ 60
Setting up the Keylock ............................................60
Canceling the Keylock Setting ................................61
Setting up a Password...................................... 61
Entering the Password.............................................61
Changing the Password ......................................... 62
If You Forget Your Password................................... 62
54
-4
Setting the Anti-Theft........................................ 63
Entering the Keycode ..............................................63
Changing the Keycode ...........................................64
Initializing the Settings ..................................... 65
Displaying the Adjustment Settings................ 66
Appendix
Carrying the Projector ...................................... 68
Maintenance ...................................................... 69
Maintenance Indicators .................................... 70
Regarding the Lamp ......................................... 71
Lamp ...................................................................... 71
Caution Concerning the Lamp ................................71
Replacing the Lamp ................................................71
Removing and Installing the Lamp Unit ................. 72
Resetting the Lamp Timer .......................................73
Connecting Pin Assignments .......................... 74
Computer Compatibility Chart ......................... 75
Troubleshooting ................................................ 76
For SHARP Assistance ..................................... 78
Specifications .................................................... 79
Dimensions ........................................................ 80
Glossary ............................................................. 81
Index ................................................................... 82
Introduction
-5

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product and save these
instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10.Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a book­case or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with a
grounding terminal. This plug will only fit into a grounding type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to qualified service personnel.
-6
Introduction
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen
into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions, as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the product to normal operation. e. If the product has been dropped or damaged in
any way. f. When the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
INTELLECTUAL PROPERTY RIGHTS
IMPORTANT
READ BEFORE USING THE PRODUCT
You have acquired a product that includes software licensed to SHARP Corporation by Lineo, Inc. (“Lineo”). The Software is protected by copyright laws, international copyright treaties, and other intellectual prop­erty laws and treaties. Lineo and its suppliers retain all ownership of, and intellectual property rights in (including copyright), the Software components and all copies thereof, provided however, that certain components of the Software are components licensed under the GNU General Public License (version
2), which Lineo supports. You may obtain a copy of the GNU General Public License at http://www.fsf.org/ copyleft/gpl.html. Lineo will provide source code for any of the components of the Software licensed under the GNU General Public License. To obtain such source code, send email to embedix­support@lineo.com.
OS: Embedix (Embedded Linux) Embedix (TM) is a registered trademark of
U.S.A. LINEO, Inc.
DLP™ (Digital Light Processing) and DMD™ (Digital Micromirror Device) are trademarks of Texas Instru­ments, Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation, in the United States and/or other countries.
PC/AT is a registered trademark of International Business Machines Corporation in the United States.
Adobe Acrobat is a trademark of Adobe Systems Incorporated.
Macintosh is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.
All other company or product names are trademarks or registered trademarks of their respective compa-
nies.
Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru­ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse as­semble or discompile the contents thereof.
-7
IMPORTANT SAFEGUARDS (cont.)
Be sure to read the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp ruptures. In case of lamp rup­ture, contact your nearest Sharp Au­thorized Projector Dealer or Service Center for a replacement. See Replacing the Lamp on page 71.
CAUTION
PRECAUCI
CAUTION
PR
BQC-PGM20X//1
Cautions concerning the setup of the projector
For minimal servicing and to maintain high image qual­ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environ­ments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Do not set up the projector in places exposed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the cur­tains and dim the lights when setting up the screen in a sunny or bright room.
Tilt the projector so that it does not go over an angle of 10 degrees when setting it.
The placement range (the horizontal angle) should be within ±10 degrees.
Be sure that the intake vent and the exhaust vent are not obstructed.
If the cooling fan becomes obstructed, a protection cir­cuit will automatically turn off the projector. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait more than 10 min-
N
utes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
Cautions regarding the transportation of the pro­jector
When transporting the projector, be sure not to subject it to hard impact and/or vibration, as this can result in damage. Take extra caution with the lens. Before mov­ing the projector, be sure to unplug the power cord from the wall outlet, and disconnect any other cables con­nected to it.
Other connected equipment
When connecting a computer or other audio-visual equipment to the projector, make the connections AF­TER turning off the projector and the equipment to be connected.
Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.
Using the projector in other Countries
The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector over­seas, be sure to use the appropriate power cord for the country you are in.
Do not subject the projector to hard impact and/ or vibration.
Take care with the lens so as not to hit or damage the surface of the lens.
Rest your eyes occasionally.
Continuously watching the screen for long hours will make your eyes tired. Be sure to occasionally rest your eyes.
Avoid locations with high or low temperature.
The operating temperature for the projector is from 41°F to 95°F (+5°C to +35°C)
The storage temperature for the projector is from –4°F to 140°F (–20°C to +60°C)
Do not block the exhaust and intake vents.
Allow at least 11.8 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction.
-8
Temperature monitor function
If the projector starts to overheat due to setup problems or block­age of the air vents, and will blink in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the TEMPERATURE WARN­ING indicator on the projector will blink, and after a 90­second cooling-off period the power will shut off. Refer to Maintenance Indicators on page 70 for details.
Info
The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.
Do not unplug the power cord during projection or cool­ing fan operation. This can create damage due to the rise in internal temperature, as the cooling fan also stops.

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet, you can download it from the Internet (http:// www.adobe.com) or install it from the CD-ROM.
To install Acrobat Reader from the CD-ROM
For Windows:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click on the My Computer icon. 3 Double click on the CD-ROM drive. 4 Double click on the acrobat folder. 5 Double click on the windows folder. 6 Double click on the desired installation program
and follow the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for languages other than those included in the CD-ROM, please download the appropriate version from the Internet.
Accessing the PDF Manuals
For Windows:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click on the My Computer icon. 3 Double click on the CD-ROM drive. 4 Double click on the manuals folder. 5 Double click on the pgm20x folder. 6 Double click on the language (name of the
folder) that you want to view.
7 Double click on the pdf file.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click on the CD-ROM icon. 3 Double click on the acrobat folder. 4 Double click on the mac folder. 5 Double click on the desired installation
program and follow the instructions on the screen.
For Macintosh:
1 Insert the CD-ROM in the CD-ROM drive. 2 Double click on the CD-ROM icon. 3 Double click on the manuals folder. 4 Double click on the pgm20x folder. 5 Double click on the language (name of the
folder) that you want to view.
6 Double click on the pdf file.
Introduction
Note
If the desired PDF file cannot be opened by double clicking the mouse, start Acrobat Reader first, then specify the desired file using the “File”, “Open menu.
See the “readme.txt file on the CD-ROM for important information on the CD-ROM not included in this operation manual.
-9

Part Names

Projector (Front and Top View)

LAMP REPLACEMENT indicator
Illuminates in green normally. Replace the lamp when the indicator illuminates in red.
POWER indicator
Illuminates in red, when the projector is in standby. When the power is turned on, this indicator will illuminate in green.
POWER button
Turns the power on or off.
70
28
28
70
TEMPERATURE WARNING indicator
Illuminates in green normally. When the internal temperature rises, this indicator will illuminate in red.
29
INPUT button
For switching input mode 1, 2 or 3.
36
MENU button
For displaying adjustment and setting screens.
LENS button
For adjusting Keystone or Digital Shift setting.
Adjustment buttons ( )
For selecting menu items.
ENTER button
For setting items selected or adjusted on the menu.
AV MUTE button
For temporarily turning off the sound and picture.
Zoom knob
Foot releases/Adjustment feet
For adjusting the projector’s height.
32
36
36
30
31
16
Attaching the terminal cover
Attach the terminal cover by placing it on the side panel of the projector and pressing it into
place, as shown in the illustration.
29
VOLUME buttons
For adjusting the speaker sound level.
33
UNDO button
For undoing an operation or returning to the default settings.
44
AUTO SYNC button
For automatically adjusting images when connected to a computer.
31
Focus ring
10
Terminal cover
29
Speaker
13
Remote control sensor
-10
Projector (Side View)
Introduction
INPUT 1 terminal
Port for DVI digital, computer RGB, and COMPONENT signals.
INPUT 2 terminal
Terminal for connecting video equipment with an S-VIDEO terminal.
AC socket
Exhaust vent
Kensington Security Standard connector
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
69
21
24
20
11
26
USB terminal
For connecting a compu­ter using a USB cable.
INPUT AUDIO terminal
21
Shared audio terminal for INPUT 1, INPUT 2, and INPUT 3.
24
INPUT 3 terminal
For connecting video equipment.
Attaching the lens cap
After putting the lens cap strap on the lens cap, pass the other end of the strap through the hole under the projector, next to the lens, as shown in the illustration.
Bottom View
-11
Part Names (cont.)

Remote Control

Remote control signal transmitter
FORWARD/BACK button
Moves forward or backwards when connected to a computer using a USB cable. Same as the [Page Down] and [Page Up] keys on a computer keyboard.
AV MUTE button
For temporarily turning off the sound and picture.
VOLUME buttons
For adjusting the speaker sound level.
INPUT 2 button
For switching the input mode to INPUT 2.
INPUT 1 button
For switching the input mode to INPUT 1.
AUTO SYNC button
For automatically adjusting images when connected to a computer.
LENS button
For adjusting Keystone or Digital Shift setting.
ENTER button
For setting items selected or adjusted on the menu.
26
30
29
29
29
44
32
36
POWER button
28
Turns the power on or off.
ENLARGE (Enlarge/Reduce)
49
buttons
For enlarging or reducing part of the image.
FREEZE button
48
For freezing images.
29
INPUT 3 button
For switching the input mode to INPUT 3.
RESIZE button
46
For switching the screen size (NORMAL, BORDER, etc).
50
GAMMA button
For correcting the brightness of an image, when the images displayed are hard to see because of the brightness of the room. Four gamma modes are available to choose from.
36
MENU button
For displaying adjustment and setting screens.
36
Adjustment buttons ( )
For selecting menu items.
33
UNDO button
For undoing an operation or returning to the default settings.
-12

Using the Remote Control

Available Range of the Remote Control

The remote control can be used to control the projector
within the ranges shown in the illustration.
Introduction
Note
The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ due to the screen material.
When using the remote control:
Be sure not to drop, expose to moisture or high temperature.
The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo­rescent lamp.

Inserting the Batteries

The batteries (two R-03 batteries (“AAA” size, UM/SUM-4, HP-16 or similar)) are included in the package.
1 Slide the cover in the direction
of the arrow to open it.
2 Insert the included batteries.
Insert the batteries making sure the polarities correctly match the
marks inside the battery compart-
ment.
and
Signal transmitter
30°
30°
Remote control
45°
23' (7 m)
Remote control sensor
3 Slide the cover in the direction
of the arrow to close it.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
Insert the batteries making sure the polarities correctly match the and marks inside the battery compart- ment.
Batteries of different types have different properties, therefore do not mix batteries of different types.
Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak. Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth.
The batteries included with this projector may be used up over a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.
Remove the batteries from the remote control if you will not be using the remote control for a long time.
-13

Accessories

Supplied accessories
Remote control RRMCGA013WJSA
Power cord (6' (1.8m)) (1)
Two R-03 batteries (AAA size, UM/SUM-4, HP-16 or similar)
(2) (3)
(4)
For U.S., Canada, etc. QACCDA007WJPZ
For Europe, except U.K. QACCV4002CEZZ
For U.K., Hong Kong and Singapore QACCB5024CENA
For Australia, New Zealand and Oceania QACCL3022CEZZ
Note
Depending on the region, projectors only ship with one power cord (see above). Use the power cord that
corresponds to the wall outlet in your country.
DVI to 15-pin D-sub cable (6' (1.8m)) QCNWGA010WJZZ
Lens cap (attached) CCAPHA001WJ01
USB cable (6' (1.8 m)) QCNWG0001WJPZ
Lens cap strap UBNDT0013CEZZ
Terminal cover (attached) GCOVD0103CESA
Carrying case GCASN0005CESA
CD-ROM UDSKA0058CEN2
Operation manual (this manual)
Quick reference guides
Optional accessories
DVI cable (9'10'' (3.0 m)) AN-C3DV 3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3CP Computer RGB cable (32'10'' (10.0 m)) AN-C10BM
5 BNC to 15-pin D-sub cable (9'10'' (3.0 m)) AN-C3BN RGB monitor loop-out adaptor (7.9'' (20 cm)) AN-A1MY DVI to 15-pin D-sub adaptor (7.9'' (20 cm)) AN-A1DV
If you cannot connect after changing computer ports, be sure to check you computer’s specifications.
If you are still having difficulty connecting, a conversion connector (commercially available) may be necessary.
<for IBM-PC, PC9821, and PC98NX systems> AN-C10PC <for PC98 systems (Except PC9821 and PC98NX systems)>
-14
Note
All cables may not be available in all regions. Please check with your nearest Sharp Authorized
Projector Dealer or Service Center.

Setup and Connections

Setup and Connections

Setup

Using the Adjustment Feet

The height of the projector can be adjusted using the adjustment feet when the surface of the projector is placed on is uneven or when the screen is slanted. The projection of the image can be made higher by adjusting the projector when it is in a location lower than the screen.
1 Press the foot releases.
Foot releases
Adjustment feet
2 Lift the projector to adjust its
height and remove your hands from the foot releases.
3 Rotate the adjustment feet to
make minor changes.
Note
When returning the projector to its origi­nal position, hold the projector firmly, press the foot releases and then lower it.
The projector is adjustable up to approxi­mately 5.5 degrees from the standard po­sition.
Info
Do not press the foot releases when the feet are extended without firmly holding the projector.
Do not hold the lens when lifting or lower­ing the projector. When lowering the projector, be careful not
to get your fingers caught in the area be­tween the adjustment feet and the projector.
Up Down
-16

Setting up the Screen

Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image.
Note
The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
For optimal image, position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
A polarizing screen cannot be used with this projector.
Standard Setup (Front Projection)
Place the projector at the required distance from the screen
according to the desired picture size. (See page 18.)
Example of Standard Setup
Setup and Connections
Side View
90°
Top View
90°
The distance from the screen to the projec-
tor may vary depending on the size of the screen. P.18
The default setting can be used, when plac-
ing the projector in front of the screen. If the
Audi­ence
projected image is reversed or inverted, re­adjust the setting to “Front” in “PRJ Mode”.
Place the projector so that the horizontal line
that passes through the center of the lens is perpendicular to the screen.
P.60
-17
Setup (cont.)

Screen Size and Projection Distance

Screen
Base line: Horizontal line passing through the lens center.
90°
Lens center
H
L:Projection distance
NORMAL Mode (4:3)
Picture (Screen) size Projection distance (L)
Diag. (X) Width Height Maximum (L1) Minimum (L2)
300"(762 cm) 240" (610 cm) 180" (457 cm) – 39' 5" (12.0 m) 0" (0.0 cm)
250"(635 cm) 200" (508 cm) 150" (381 cm) 39' 8" (12.1 m) 32' 10" (10.0 m) 0" (0.0 cm)
200"(508 cm) 160" (406 cm) 120" (305 cm) 31' 9" (9.7 m) 26' 3" (8.0 m) 0" (0.0 cm)
150"(381 cm) 120" (305 cm) 90" (229 cm) 23' 9" (7.2 m) 19' 8" (6.0 m) 0" (0.0 cm)
100"(254 cm) 80" (203 cm) 60" (152 cm) 15' 10" (4.8 m) 13' 1" (4.0 m) 0" (0.0 cm)
84" (213 cm) 67" (170 cm) 50" (127 cm) 13' 3" (4.0 m) 10' 11"(3.3 m) 0" (0.0 cm)
72" (183 cm) 58" (147 cm) 43" (109 cm) 11' 4" (3.5 m) 9' 4" (2.9 m) 0" (0.0 cm)
60" (152 cm) 48" (122 cm) 36" (91 cm) 9' 5" (2.9 m) 7' 9" (2.4 m) 0" (0.0 cm)
40" (102 cm) 32" (81 cm) 24" (61 cm) 6' 3" (1.9 m) 5' 2" (1.6 m) 0" (0.0 cm)
Distance from the lens
center to the bottom
of the image (H)
STRETCH Mode (16:9)
Picture (Screen) size Projection distance (L)
Diag. (X) Width Height Maximum (L1) Minimum (L2)
250" (635 cm) 218" (554 cm) 123" (312 cm) – 35'9" (10.9 m) –20 27 / 64" (–51.9 cm)
225" (572 cm) 196" (498 cm) 110" (279 cm) 38' 11" (11.9 m) 32' 2" (9.8 m) –18 25 / 64" (–46.7 cm)
200" (508 cm) 174" (442 cm) 98" (249 cm) 34' 7" (10.5 m) 28' 7" (8.7 m) –16 22 / 64" (–41.5 cm)
150" (381 cm) 131" (333 cm) 74" (188 cm) 25' 11" (7.9 m) 21' 5" (6.5 m) –12 16 / 64" (–31.1 cm)
133" (338 cm) 116" (295 cm) 65" (165 cm) 22' 11" (7.0 m) 18' 12"(5.8 m) –10 56 / 64" (–27.6 cm)
106" (269 cm) 92" (234 cm) 52" (132 cm) 18' 3" (5.6 m) 15' 1" (4.6 m) –8 42 / 64" (–22.0 cm)
100" (254 cm) 87" (221 cm) 49" (124 cm) 17' 3" (5.3 m) 14' 3" (4.3 m) –8 11 / 64" (–20.8 cm)
92" (234 cm) 80" (203 cm) 45" (114 cm) 15' 10" (4.8 m) 13' 1" (4.0 m) –7 33 / 64" (–19.1 cm)
84" (213 cm) 73" (185 cm) 41" (104 cm) 14' 5" (4.4 m) 11' 11" (3.6 m) –6 55 / 64" (–17.4 cm)
72" (183 cm) 63" (160 cm) 35" (89 cm) 12' 4" (3.8 m) 10' 3" (3.1 m) –5 57 / 64" (–14.9 cm)
60" (152 cm) 52" (132 cm) 29" (74 cm) 10' 3" (3.1 m) 8' 6" (2.6 m) –4 58 / 64" (–12.5 cm)
40" (102 cm) 35" (89 cm) 20" (51 cm) 6' 10" (2.1 m) 5' 7" (1.7 m) –3 17 / 64" (–8.3 cm)
Distance from the lens
center to the bottom
of the image (H)
The formula for picture size and projection distance L1 (ft)
= (0.048539X – 0.037278) / 0.3048
L2 (ft)
= (0.040172X – 0.037561) / 0.3048
H (in) = 0
X: Picture size (diag.) (in) L: Projection distance (m) L1: Maximum projection distance (ft) L2: Minimum projection distance (ft) H: Distance from the lens center to
the bottom of the image (in)
The formula for picture size and projection distance L1 (ft)
= (0.052882X – 0.037278) / 0.3048
L2 (ft)
= (0.043766X – 0.037561) / 0.3048
H (in) = –0.08171X
BORDER Mode (4:3)
Picture (Screen) size Projection distance (L)
Diag. (X) Width Height Maximum (L1) Minimum (L2)
200" (508 cm) 160" (406 cm) 120" (305 cm) – 35' 0" (10.7 m) –20" (50.8 cm)
180" (457 cm) 144" (366 cm) 108" (274 cm) 38' 1" (11.6 m) 31' 6" (9.6 m) –18" (45.7 cm)
150" (381 cm) 120" (305 cm) 90" (229 cm) 31' 9" (9.7 m) 26' 3" (8.0 m) –15" (38.1 cm)
100" (254 cm) 80" (203 cm) 60" (152 cm) 21' 1" (6.4 m) 17' 5" (5.3 m) –10" (25.4 cm)
84" (213 cm) 67" (170 cm) 50" (127 cm) 17' 9" (5.4 m) 14' 8" (4.5 m) –8 26 / 64" (–21.3 cm)
72" (183 cm) 58" (147 cm) 43" (109 cm) 15' 2" (4.6 m) 12' 6" (3.8 m) –7 13 / 64" (–18.3 cm)
60" (152 cm) 48" (122 cm) 36" (91 cm) 12' 7" (3.8 m) 10' 5" (3.2 m) –6" (–15.2 cm)
40" (102 cm) 32" (81 cm) 24" (61 cm) 8' 4" (2.6 m) 6' 11"(2.1 m) –4
Distance from the lens
center to the bottom
of the image (H)
" (–10.2 cm)
The formula for picture size and projection distance L1 (ft)
= (0.064719X – 0.037278) / 0.3048
L2 (ft)
= (0.053563X – 0.037561) / 0.3048
H (in) = 0.100X
Note
There is an error of ± 3% in the formula above.
Values with a minus (–) sign indicate the distance of the lens center below the bottom of the image.
-18

Projecting a Reversed/Inverted Image

Projection from behind the screen
Place a translucent screen between the projector and the
audience.
Reverse the image by setting Rear in PRJ Mode. See
page 60 for use of this function.
When using the default setting.
On-screen Display
Setup and Connections
Projection using a mirror
Place a mirror (normal flat type) in front of the lens.
Reverse the image by setting Rear in PRJ Mode, when the
mirror is placed on the audience side. See page 60 for use of this function.
Info
When using a mirror, be sure to carefully position both the pro­jector and the mirror so the light does not shine into the eyes of the audience.
Ceiling-mount setup
It is recommended that you use the optional Sharp ceiling-mount
bracket for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount bracket (sold separately.) (AN­PGCM90 ceiling-mount bracket, its AN-EP101B extension tube and AN-JT200 universal bracket, adaptor for non-level ceiling installation (for U.S.A.), BB-M20T ceiling adaptor, its BB­NVHOLDER280, BB-NVHOLDER550, BB-NVHOLDER900 ceiling mount systems (for GERMANY), or AN-60KT ceiling­mount bracket, its AN-TK301/AN-TK201 and AN-TK302/AN­TK202 extension tubes (for countries other than the U.S.A. and GERMANY))
Be sure to adjust the position of the pro-
jector to match the distance (H) from the lens center position (see page 18) to the lower edge of the image, when mounting the projector on the ceiling.
Invert the image by
setting Ceiling + Front in PRJ Mode”.
The image is reversed.
When using the default setting.
On-screen Display
The image is reversed.
When using the default setting.
On-screen Display
The image is inverted.
-19

Connecting the Projector to Other Devices

Before Connecting

Note
Before connecting, be sure to turn off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connections are made.
Be sure to read the operation manuals of the devices to be connected before making connections.

This projector can be connected to:

A computer using:
A DVI to 15-pin D-sub cable (See page 21.)
A DVI cable (type AN-C3DV) (sold separately)
(See page 22.)
Component video or audio-visual equipment:
A DVD player or DTV* decoder (See page 23.)
A VCR, Laser disc player or other audio-visual equipment
(See page 24.)
*DTV is the umbrella term used to describe the new digital television system in the United States.
A monitor using:
An RGB monitor loop-out adaptor (AN-A1MY) (sold sepa­rately) and an RGB cable (commercially available). (See page 25.)
Connecting the Power
Supplied accessory
Cord
1 Plug in the supplied power
cord into the AC socket on the rear of the projector.
Power cord
-20

Connecting the Projector to a Computer

Connecting to a Computer Using the DVI to 15-pin D-sub Cable
1 Connect the projector to the
computer using the supplied DVI to 15-pin D-sub cable.
Secure the connectors by tightening the thumbscrews.
2 To input audio signal, connect
the projector to the computer using a ø3.5 mm stereo audio cable (commercially available or available as Sharp service part QCNW-4870CEZZ).
Note
See page 75 Computer Compatibility Chart for a list of computer signals com­patible with the projector. Use with com­puter signals other than those listed may cause some of the functions not to work.
When connecting the projector to a com­puter in this way, select RGB for “Signal Type in the Picture menu. See page 40.
A Macintosh adaptor may be required for use with some Macintosh computers. Con­tact your nearest Sharp Authorized Projector Dealer or Service Center.
Supplied accessory
To RGB Output port
To Audio Output port
Notebook computer
DVI to 15-pin D-sub cable
ø3.5 mm stereo audio cable
2
(commercially available or available as Sharp service part QCNW-4870CEZZ)
DVI to 15-pin D-sub cable
1
Setup and Connections
Connecting the thumbscrew cables
Connect the thumbscrew cable making sure that it
fits correctly into the port. Then, firmly secure the connectors by tightening the screws on both sides of the plug.
Do not remove the ferrite core attached to the D VI
to 15-pin D-sub cable.
Ferrite core
-21
Connecting the Projector to Other Devices (cont.)
Connecting to a Computer Using a DVI Cable (Sold Separately)
This projector comes installed with a DVI digi­tal input terminal in which computer digital im­age signals can be directly input.
1 Connect the projector to the
computer using the DVI cable.
2 To input audio signal, connect
the projector to the computer using a ø3.5 mm stereo audio cable (commercially available or available as Sharp service part QCNW-4870CEZZ).
Note
This DVI port is DVI version 1.0 compat­ible. Therefore when the signal is input from copy guard system compatible (DVI version 2.0) equipment, no signal will be received.
Optional accessory
To DVI Digital Output port
To Audio Output port
Desktop computer
DVI cable
1
(sold separately)
DVI cable Type: AN-C3DV (9'10" (3.0 m))
ø3.5 mm stereo
2
audio cable (commercially available or available as Sharp service part QCNW-4870CEZZ)
Plug and Play function (when connecting to a 15-pin terminal)
This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
Before using the “Plug and Play function, be sure to turn on the projector first and the connected
computer last.
Note
The DDC “Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible computer.
-22

Connecting to Video Equipment

Connecting to Component Video Equipment
Use a 3 RCA to 15-pin D-sub cable and DVI to 15-pin D-sub adaptor when connecting to the INPUT 1 terminal, component video equipment such as DVD players and DTV* decoders.
*DTV is the umbrella term used to describe the new digital television system in the United States.
1 Connect the 3 RCA to 15-pin D-
sub cable using the DVI to 15­pin D-sub adaptor.
2 Use the above cables to con-
nect the projector and the video equipment.
3 Connect the projector and the
video equipment using an au­dio cable (commercially avail­able).
Optional accessories
Audio cable
3
(commercially available)
To audio output terminal
DVD player or DTV* decoder
DVI to 15-pin
1
D-sub adaptor (sold separately)
3RCA to 15-pin D-sub cable Type: AN-C3CP (9'10" (3.0 m))
DVI to 15-pin D-sub adaptor Model: AN-A1DV (7.9" (20 cm))
To analog component output terminal
3 RCA to 15-pin
2
D-sub cable (sold separately)
Setup and Connections
Note
When connecting the projector to the video equipment in this way, select Com­ponent for “Signal Type in the Picture menu. See page 40.
A ø3.5 mm stereo minijack to RCA audio cable (commercially available) is recom­mended for audio input.
-23
Connecting the Projector to Other Devices (cont.)
Connecting to Video Equipment Using an S-VIDEO, a Composite Video or an Audio Cable
Using an S-VIDEO, video, or audio cable, a VCR, laser disc player or other audio-visual equipment can be connected to INPUT 2, IN­PUT 3 and AUDIO terminals.
VCR or other audio-visual equipment
To S-VIDEO output terminal
To video output terminal
To audio output terminal
1 Connect the projector to the
video equipment using an S­VIDEO cable or a composite video cable (both commercially available).
2 Connect the projector to the
video equipment using an au­dio cable (commercially avail­able).
1
Audio cable (commercially available)
2
Composite video cable
1
(commercially available)
S-VIDEO cable (commercially available)
Note
The S-VIDEO INPUT terminal uses a video signal system in which the picture is separated into color and luminance sig­nals to realize a higher-quality image. For realizing a higher-quality image, use a commercially available S-VIDEO cable to connect the S-VIDEO terminal on the pro­jector and the S-VIDEO output terminal on the video equipment.
A ø3.5 mm minijack to RCA audio cable (commercially available) is recommended for audio input.
-24

Connecting to a Monitor

Watching Images on Both the Projector and a Monitor
You can display computer images on both the projector and a separate monitor using an RGB monitor loop-out adaptor and an RGB cable.
1 Connect the projector to the
computer and monitor using an RGB monitor loop-out adap­tor (sold separately) and an RGB cable (commercially avail­able).
2 In the “Options(1)” menu, se-
lect Monitor Out and then Yes (Y cable)”.
If “Disable is selected, the projected image will be dimmer. This does not indicate a malfunction. For details, see page 58.
Note
When using an RGB monitor loop-out adaptor (sold separately), make sure that the cable is connected to the monitor.
Analog RGB signals as well as Component signals can be output to the monitor.
Optional accessory
To RGB input port
RGB cable (commercially available)
RGB monitor loop-out adaptor
1
(sold separately)
Black: to the monitor Blue: to the computer
RGB monitor loop-out adaptor Type: AN-A1MY (7.9" (20 cm))
Setup and Connections
Monitor
Notebook computer
To RGB output port
Info
Only analog RGB/Component signals entered into the DVI port can be output. Signals from equipment connected to the DVI digital port cannot be output.
Using INPUT 1 Terminal with the Terminal Cover Attached to the Projector
The INPUT 1 terminal can be used with the ter­minal cover folded as shown in the illustra­tion.
-25
Connecting the Projector to Other Devices (cont.)

Using the Wireless Presentation Function of the Remote Control

The Wireless Presentation function on the projector works the same as the [Page Up] and [Page Down] keys on a computer keyboard. It can also be used to move forward or backward when viewing images of presentation software such as Power PointTM.
Using the Wireless Pre­sentation Function
1 Connect the projector to the
computer using the supplied USB cable.
Note
This function only works with Microsoft Windows OS and Mac OS. However, this function does not work with the following operating systems that do not support USB.
Versions earlier than Windows 95.
Versions earlier than Windows NT 4.0.
Versions earlier than Mac OS 8.5.
Supplied accessory
USB cable
USB port
Notebook computer
USB cable
2 Press while using
presentation software on your computer.
Press FORWARD to move the page down.
Press BACK to move the page up.
-26
FORWARD/BACK button

Basic Operation

Basic Operation

Image Projection

Basic Procedure

Connect the required external equipment to the projector before operating the following procedures. The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language ac­cording to the procedure on page 30.
1 Plug the power cord into the
wall outlet.
The POWER indicator illuminates up in red, and the projector enters standby mode.
Projector indicators
LAMP REPLACEMENT indicator
POWER indicator
2 Press
on the projector or
on the remote control.
The POWER indicator illuminates in green. After the LAMP REPLACEMENT indicator illuminates, the projector is ready to start operation.
Note
The LAMP REPLACEMENT indica­tor illuminates, indicating the status of the lamp.
Green: The lamp is ready. Green blinking: The lamp is
warming up.
The lamp should be replaced.
Red:
If the power is turned off and on right after again, the LAMP REPLACEMENT indicator may take time to
illuminate
When “Anti-Theft” is set, the keycode input box will appear.
Enter the keycode.
Note
When entering the keycode, press the buttons previously set on the projector or the remote control.
Info
When “Anti-Theft” is set, enter the keycode or the input display will not appear. Even when the signal is in­put, the display cannot appear.
POWER button
INPUT button
MENU button
buttons ENTER
button
.
POWER button
INPUT 1/2/3 buttons
MENU button
buttons
ENTER button
Keycode input box
-28
3 Press , or on the
remote control to select the INPUT Mode.
Pressing on the projector switches the inputs in the following order:
"On-screen Display (Example)
INPUT 1 Mode
Using
DVI digital
INPUT 1 INPUT 2 INPUT 3
Note
When no signal is received, “NO SIGNAL will be displayed. When a signal that the projector is not pre­set to receive is received, NOT REG. will be displayed.
About the INPUT Modes
INPUT 1 (RGB/ Component)
INPUT 2 (S-Video)
INPUT 3 (Video)
Used for projecting im­ages from equipment that sends RGB signals or Component signals con­nected to the DVI-DIGI­TAL/ANALOG input port.
Used for projecting im­ages from equipment connected to the S­VIDEO input terminal.
Used for ages connected to the VIDEO input terminal.
projecting
from equipment
Using Analog RGB
Using Component
➝➝
INPUT 2 Mode
Using S-Video
INPUT 3 Mode
Using Video
Basic Operation
im-
4 Press or on the remote
control to adjust the volume of the speaker.
Note
Pressing will raise the volume.
Pressing
On the projector, the volume can be
adjusted by pressing or .
, on the projector operate
as cursor buttons (
selecting setup or adjustment functions while adjusting menus or the lens.
will lower the volume.
, ) when
VOLUME buttons
-29
Image Projection (cont.)
5 Press to temporarily turn off
the picture and sound.
Note
Pressing again will turn the pic- ture and the sound back on.
6 Press , then press again
while the confirmation message is displayed, to turn off the pro­jector.
Note
If you accidentally pressed and do not want to turn off the power, wait until the confirmation message disappears.
AV MUTE button
POWER button
Info
Do not unplug the power cord dur­ing projection or cooling fan opera­tion. This can cause damage due to the rise in internal temperature, as the cooling fan also stops.
When connected to equipment such as an amplifier, be sure to turn off the power to the equipment con­nected first and then to the projec­tor.

Selecting the On-screen Display Language

The on-screen display language of the projector can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japa­nese.
1 Press .
The menu will be displayed.
2 Press or to select Lan-
guage”.
-30
3 Press or to select the
desired language, and then press
.
4 Press .
The desired language will be set as the on-screen display.

Adjusting the Lens

The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector.
Zoom knob
Basic Operation
1 The focus is adjusted by rotat-
ing the focus ring.
2 Zooming is adjusted by mov-
ing the zoom knob.
Focus ring
t
u
o
m
o
o
Z
in
Zoom
-31

Correcting the Trapezoidal Distortion (Keystone Correction)

Correcting the Trap­ezoidal Distortion
This function allows for Keystone (On-screen Trapezoidal Distortion) Correction.
Note
Keystone Correction is the correction for trapezoidal distortion that occurs when the image is positioned away from the center axis of the screen.
The trapezoidal distortion can be corrected up to an angle of approximately ±35 de­grees.
LENS button
ENTER button
Normal screen
buttons
UNDO button
Keystone Correction screen
1 Press
Pressing
DER, STRETCH or SMART STRETCH screen is displayed will start the Digital Shift function. See page 33.
2 Press
.
again while the BOR-
or
just the Keystone correction.
If you want to make more detailed cor­rections, press pattern, and then press
to make the adjustments.
Note
Since the trapezoidal distortion of the image can be corrected up to an angle of approximately ±35 de­grees, the actual screen can be di­agonally set up to that angle as well. (For more details on the settings, see page 8.)
Press
rection.
to cancel Keystone Cor-
to display the test
to ad-
or
Compresses upper side.
Compresses lower side.
Test pattern
3 Press
You can use the same settings used in NORMAL mode 4:3 for 16:9.
Straight lines or the edges of images may appear jagged while adjusting the image.
-32
.
Note
Digital Shift Setting
For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television
system in the United States.
Press to move the projected image upwards.
Press to reset the image.
UNDO button
The Digital Shift function works with BORDER, STRETCH or SMART STRETCH screen. For details, see page 47.
Press to move the projected image downwards.
Press to reset the image.
Basic Operation
Easy to Use Functions
Setting the Video Signal......................................................................................page 55
Displaying Dual Pictures (Pict in Pict) ..............................................................page 51
Video Digital Noise Reduction (DNR) System ..................................................page 54
For details, see the explanation of each setting on the respective page.
-33

Menu Bar Items

This list shows the items that can be set in the projector.
INPUT 1 Mode
Main menu Sub menu Main menu Sub menu
Picture
Page 40
Fine Sync Clock
Page 42
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Signal Type
Progressive Mode
Phase
H-Pos
V-Po s
Reset
Save Setting
Select Setting
Special Modes
Signal Info
Auto Sync
Auto Sync Disp [ON/OFF]
150
150
30
60
+30
-30
-30
+30
+30
-30
+30-30
+30-30
-30
+30
+30
-30
-3
+3
+150
+30
+150
+60
RGB Component
2D Progressive 3D Progressive Film Mode
Resolution Vert Freq
Resolution
×
1
1024
768
×
2
600
800
7
Resolution Vert Freq
Resolution
×
1
768
1024
2
800 × 600
7
Resolution
×
480
640
1
720 × 480
2
480p
3
7
Resolution Hor Freq Vert Freq
OFF Normal High Speed
640 × 480
31.5 KHz 60 Hz
Vert Freq
60 Hz 75 Hz
Vert Freq
60 Hz 75 Hz
Options (1)
Page 51
Options (2)
Page 58
Language
Page 31
Pict in Pict [ON/OFF]
Power Save [ON/OFF]
sRGB [ON/OFF]
Auto Search [ON/OFF]
DNR
OSD Display
Image Capture
Background
Startup Image
Auto Power Off [ON/OFF]
Monitor Out
Lamp Timer
Break Timer
PRJ Mode
Keylock Level
Password
Anti-Theft
All Reset
English Deutsch Español Nederlands Français Italiano Svenska Português
OFF Level 1 Level 3
Normal Level A Level B
Save Image Delete
Sharp Custom Blue None
Sharp Custom None
Disable Yes (Y Cable)
Front Ceiling + Front Rear Ceiling + Rear
Normal Level A Level B
Old Password New Password Reconfirm
Old Code New Code Reconfirm
Status
Page 66
Note
The resolution, vertical frequency and horizontal frequency figures displayed above are for example purposes only.
When DVI digital signals have been entered into INPUT 1, in “Picture only CLR Temp”, Red and Blue can be adjusted and in Fine Sync only Signal Info, Auto Sync and Auto Sync Disp can be used.
When the signal type is set as “Component, in the Picture menu of INPUT 1 Color, Tint” and Sharp are displayed. Some items cannot be reset, even when All Reset in Options (2) has been selected. For details see page
65.
-34
INPUT 2 / 3 Mode
Main menu Sub menu Main menu Sub menu
Picture
Page 40 Page 58
Options (1)
Page 52
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
Reset
Progressive Mode
Power Save [ON/OFF]
Auto Search [ON/OFF]
DNR
OSD Display
Video System
Background
Startup Image
Auto Power Off [ON/OFF]
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+30–30
+3–3
2D Progressive 3D Progressive Film Mode
OFF Level 1 Level 3
Normal Level A Level B
Auto PAL (50/60Hz) SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N
Sharp Custom Blue None
Sharp Custom None
Options (2) Lamp Timer
Break Timer
PRJ Mode
Keylock Level
Password
Anti-Theft
All Reset
Language
Page 31
Status
English Deutsch Español Nederlands Français Italiano Svenska Português
Page 66
Front Ceiling + Front Rear Ceiling + Rear
Normal Level A Level B
Old Password New Password Reconfirm
Old Code New Code Reconfirm
Basic Operation
-35

Using the Menu Screen

This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following proce­dure.
On-screen menu for INPUT 1 RGB mode
On-screen menu for INPUT 2 or INPUT 3 Mode
Menu Bar (Main Menu)

Basic Operations (Adjustments)

1 Press .
Note
The “Picture” menu screen for the selected input mode is displayed.
The on-screen display shown on the right is displayed when the INPUT 1 mode is selected.
Menu Bar (Main Menu)
MENU button
buttons
ENTER button
MENU button
-36
""
"On-screen Display
""
buttons
ENTER button
2 Press
or
to select the
menu you want to adjust.
Note
For details on the menus, see the tree charts on pages 34 and 35.
3 Press
or
to select the
item you want to adjust.
Note
To display a single adjustment item, press Only the menu bar and the selected adjustment item will be displayed. Then if you press
lowing item (Phase is after Clock”) will be displayed.
Press
screen.
after selecting the item.
||
|
||
to return to the previous
or
, the fol-
Basic Operation
4 Press
or
to adjust the
item selected.
When you release
adjustement is stored.
5 Press
The on-screen display is cleared.
.
or
the
-37
Using the Menu Screen (cont.)
MENU button

Basic Operations (Settings)

1 Press
The “Picture menu screen for the selected input mode is displayed.
The on-screen display shown on the right is displayed when the INPUT 1 mode is selected.
2 Press
menu you want to adjust.
For details on the menus, see the tree charts on pages 34 and 35.
3 Press
item you want to set.
Note
Note
.
or
or
to select the
to select the
buttons
ENTER button
MENU button
buttons
ENTER button
On-screen Display
-38
Note
Press
screen.
In some menus, select the icon us­ing ”.
to return to the previous
Sub menu
4 Press .
The cursor shifts to the sub menu.
5 Press or to select the
setting of the item displayed in the sub menu.
6 Press .
The item selected is set.
Sub menu
Basic Operation
Note
Some adjustment items will display a confirmation message. When setting an item, press or
to select “Ye s ” or OK and then
press
.
7 Press .
The menu will disappear.
-39

Adjusting the Picture

You can adjust the projector’s picture to your preferences with the following picture settings.
Selected Item Description
Contrast
Bright
Color
Tint
Sharp
Red
Blue
CLR Temp
For adjusting the contrast level
For adjusting the brightness of an image
For adjusting the color intensity of the image
For adjusting the tones of an image
For making sharper or softer the contour of an image
For adjusting the redness level
For adjusting the blue level
For adjusting the color temperature of an image

Adjusting Image Preferences

Adjust the Picture menu For adjustments, see page 36.
Note
“Color, Tint and Sharp are not dis- played when selecting INPUT 1 and the Signal Type is RGB .
The picture adjustments can be stored separately in each input mode.
When the signal type in INPUT 1 has been set to Component, Sharp can be adjusted when 480I, 480P, 720P or 1080I signals are entered.
To reset all adjustment items, select Re- set and press
.
button
For less contrast
For less brightness
For less color intensity
Skin tones become purplish
For less sharpness
For weaker red
For weaker blue Decreases color
temperature for warmer, reddish, incandescent­like images.
For more contrast
For more brightness
For more color intensity
Skin tones become greenish
For more sharpness
For stronger red
For stronger blue Increases color
temperature for cooler, bluish, fluorescent-like images.
button

Selecting the Signal Type

This function allows you to select the input signal type RGB or Component for INPUT1.
Select “Signal Type” in the “Picture” menu For settings, see page 38.
Note
RGB Set when RGB signals are received.
Component Set when Component signals are received.
-40

Progressive Mode

This function allows you to select the pro­gressive display of a video signal. The pro­gressive display projects a smoother video image.
Select Progressive Mode in the Pic­ture menu For settings, see page 38.
Note
2D Progressive This function is useful to display fast­moving images such as sports and ac­tion films. This mode optimizes the im­age in a displayed frame.
3D Progressive
This function is useful to display relatively slow-moving images such as drama and documentary more clearly. This mode optimizes the image by esti­mating the movement of a number of pre­ceding and succeeding frames.
Film Mode
Reproduces the image of film source clearly. Displays the optimized image of film transformed with three-two pull down (NTSC and PAL60Hz) or two-two pull down (PAL50Hz and SECAM) enhance­ment to progressive mode images. * The film source is a digital video record-
ing with the original encoded as is at 24 frames/second. The projector can con­vert this film source to progressive video at 60 frames/second with NTSC and PAL60Hz or at 50 frames/second with PAL50Hz and SECAM to play back a high-definition image.
Basic Operation
When using progressive inputs, these inputs are directly displayed therefore 2D Progressive, 3D Progressive and Film Mode cannot be selected. These modes can be selected in interlace signals other than 1080
In NTSC or PAL60Hz, even if the 3D Pro­gressive mode has been set, the three­two pull down enhancement will be en­abled automatically, when the film source has been entered.
In PAL50Hz or SECAM, the two-two pull down enhancement will be enabled only in the Film Mode, when the film source has been entered.
I.
-41

Adjusting Computer Images

Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen.
Selected Item Description
Clock
Phase
H-Pos
V-Pos

When Auto Sync is OFF

When Auto Sync is OFF, interference such as flickering or vertical stripes may oc­cur if displaying tilings or vertical stripes. Should this occur, adjust “Clock”, “Phase”, H-Pos and “V-Po s for obtaining an opti- mum image.
Adjusts vertical noise.
Adjusts horizontal noise (similar to tracking on your VCR).
Centers the on-screen image by moving it to the left or right.
Centers the on-screen image by moving it up or down.
Select “Clock”, “Phase”, “H-Pos or “V- Pos in the Fine Sync menu For adjustments, see page 36.
Note
Computer image adjustments can be made easily by pressing
details.
. See page 44 for

Saving Adjustment Settings

This projector allows you to store up to seven adjustment settings for use with various com­puters.
Select “Save Setting” in the “Fine Sync” menu For saving, see page 38.
-42

Selecting Adjustment Settings

Adjustment settings stored in the projector can be easily accessed.
Select Select Setting in the “Fine Sync menu For details, see page 38.
Note
If a memory position has not been set, a resolution and frequency setting will not be displayed.
When selecting a stored adjustment set­ting with Select Setting, you can set the projector in the stored adjustments.

Special Mode Settings

Ordinarily, the type of input signal is detected and the correct resolution mode is automati­cally selected. However, for some signals, the optimal resolution mode in Special Modes on the Fine Sync menu screen may need to be selected to match the computer display mode.
Set the resolution by selecting Special Modes in the Fine Sync menu For details, see page 38.
Basic Operation
Note
Avoid displaying computer patterns which repeat every other line (horizontal stripes). (Flickering may occur, making the image hard to see.)
When a DVD player or Digital Video is connected, select 480P as the input sig­nal. See Checking the Input Signal below for
information on the currently selected input signal.

Checking the Input Signal

This function allows you to check the current input signal information.
Select Signal Info in the Fine Sync menu For confirmation, see page 36.
Note
The projector will display the number of scanned lines available input from audio­visual equipment such as a DVD player or Digital Video.
-43
Adjusting Computer Images (cont.)

Auto Sync Adjustment

Used to automatically adjust a computer im­age.
Select Auto Sync in the Fine Sync menu For settings, see page 38.
Note
When setting to Normal or
High Speed”:
Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a com­puter.
Manual adjustments should be per­formed:
When the optimum image cannot be achieved with Auto Sync adjustment. See page 42.
Auto Sync adjustment may take some time to complete, depending on the im­age of the computer connected to the pro­jector.
When setting Auto Sync to OFF orHigh Speed, and if
Sync will be executed in High Speed mode. If the button is pressed again within one minute, Auto Sync will be ex­ecuted in “Normal” mode.
is pressed Auto
Screen display during Auto Sync
AUTO SYNC button

Auto Sync Display Function

Used to set the screen displayed during Auto Sync.
Select Auto Sync Disp in the Fine Sync menu For settings, see page 36.
Note
.....The image set as a background
image is projected.
..... The computer image being ad-
justed is displayed.
-44

Easy to Use Functions

Easy to Use Functions

Selecting the Picture Display Mode

This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “FULL”, “DOT BY DOT”, “BORDER”, “STRETCH” or “SMART STRETCH” image.
Switching the Picture Display Using Different Input Signals
1 Press
Each time
changes as shown on page 47.
Note
In the Dot by Dot Mode, images are dis­played in the original resolution, therefore they will not be enlarged.
To return to the standard image, press
while “RESIZE” is displayed on the screen.
.
is pressed, the display
RESIZE button
Screen display of the picture display mode
46
-46
COMPUTER
SVGA (800 × 600)
4:3 aspect ratio
Other aspect ratios
NORMAL” is fixed when XGA (1024 × 768) signals are entered.
Resolution lower than
XGA
XGA
Resolution higher than
XGA
XGA (1024 × 768)
SXGA (1280 × 960)
UXGA (1600 × 1200)
SXGA (1280 × 1024)
Input Signal
4:3 aspect ratio
4:3 aspect ratio
4:3 aspect ratio
NORMAL
1024 × 768
1024 × 768
1024 × 768
1024 × 768
960 × 768
NORMAL
Projects a full screen image
while maintaining the aspect ratio.
FULL
1024 × 768
Output screen image
FULL
Projects a full screen image
while ignoring the aspect ratio.
DOT BY DOT
800 × 600
1280 × 960
1600 × 1200
1280 × 1024
DOT BY DOT
Projects the original resolution
signal of the image.
SXGA (1280 × 1024)
VIDEO
480I, 480P, NTSC
PAL, SECAM
720P, 1080I
4:3 aspect ratio.
Letter box, squeeze
16:9 aspect ratio
STRETCH is fixed when 720P or 1080 * The Digital Shift function can be used with these images.
Input Signal
4:3 aspect ratio
480I, 480P, NTSC,
PAL, SECAM
Letter box
NORMAL
1024 × 768
I signals are entered.
NORMAL
Projects a full screen image.
BORDER
768 × 576*
STRETCH
1024 × 576*
SMART STRETCH
1024 × 576*
Easy to Use Functions
Output screen image
BORDER
Projects 4:3 image fully in
STRETCH (the following
column) image.
STRETCH
Projects 16:9 image evenly
over entire screen
(top/bottom black bands).
SMART STRETCH
Projects the image fully in a
16:9 screen by enlarging only
the surrounding areas while
keeping the aspect ratio in
the middle part of the image
at 4:3.
720P, 1080I
Squeeze
16:9 aspect ratio
-47

Displaying a Still Image

This function allows you to instantly freeze a moving image. This is useful when you want to display a still image from a computer or video, giving you more time to explain the image to the audience.
Storing an Image in Still Image Format
1 Press .
The projected image is frozen.
FREEZE button
2 Press again to return to the
moving image from the cur­rently connected device.
"On-screen Display
48
-48

Enlarging a Specific Portion of an Image

This function allows you to enlarge a specific portion of an image. This is useful when you want to display a detailed portion of the image.
Displaying an Enlarged Portion of an Image
1 Press
Enlarges the image.
Pressing
duces the projected image.
.
or enlarges or re-
Note
To enlarge
×1 ×4 ×9 ×16 ×36 ×64×2 ×3
To reduce
You can change the location of the enlarged image using
or
When an SXGA displayed, ×2 and ×3 cannot be selected.
2 Press
.
to cancel the opera-
+
or UXGA image is
tion, then the magnification returns to ×1.
ENLARGE (Enlarge/ Reduce) buttons
buttons
,
,
"On-screen Display
Easy to Use Functions
Note
In the following cases, the image will return to the normal size (×1).
When the input mode is changed.
When
When the input signal is changed.
When the input signal resolution
and refresh rate (vertical frequency) change.
has been pressed.
-49

Gamma Correction Function

Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. When you are displaying images with frequent dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the impression of greater depth in the image.
Selected Mode
STANDARD
PRESENTATION
CINEMA
GAME
For Standard picture
Brightens darker portions of image for more enhanced presentations.
Gives greater depth to darker portions of image for a more exciting theater experience.
Natural color gradation for playing a game, etc.
Adjusting Gamma Correction
1 Press .
Each time is pressed, the gamma level toggles between the different types of gamma modes.
2 Depending on the input mode
and signal, pressing GAMMA is displayed will re­turn you to the respective gamma mode.
while
Description
GAMMA button
UNDO button
STANDARD GAME
INPUT mode
INPUT1
INPUT2 S-Video STANDARD INPUT3 Video STANDARD
50
-50
INPUT signal GAMMA mode
RGB
Component
PRESENTATION
CINEMA
PRESENTATION CINEMA

Displaying Dual Pictures (Pict in Pict)

Picture in Picture function allows you to display two pictures on the same screen. You can display the image input from INPUT 2 or 3 as an inset picture overlapping the main picture from INPUT 1. (This function can only be set in the RGB menu.)
Displaying the Inset Picture
Select “Pict in Pict” in the “Options (1)” menu For displaying, see page 36.
1 Press
Select to clear the Pict in Pict mode.
to select .
2 Press or on the remote
control or
to switch the image in the inset picture.
3 Press
the position of the inset picture.
Press
ing or to make the frame disappear.
4 Press
ture.
The inset picture will be moved to the inset picture frame.
Note
The inset picture can only be displayed with composite video (NTSC/PAL/ SECAM) or S-Video signal.
The Freeze function works only with the inset picture, when the Pict in Pict mode is in operation.
When the signal entered into INPUT 1 is as follows, Pict in Pict does not work:
With a resolution that overexceeds
SXGA.
When the input signal is 480
720P or 1080I.
When the input signal has changed to
the Interlace mode using RGB signals.
When the picture display mode is set to
DOT BY DOT”.
When no signals are sent to INPUT 1,
or when the resolution or refresh rate (vertical frequency) is changed.
Press
in the inset picture.
or
on the projector to switch the image
on the projector
,
,
or
to stop the frame from mov-
to set
to move the inset pic-
I, 480P,
on the remote control or
Easy to Use Functions
-51

Selecting the Power Save Mode

The Power Save Mode or the Automatic Power Shutoff function allows you to reduce the power consumption of the projector.

Setting the Power Save Mode

Function to control the quantity of projected light. Select “ON” or “OFF” to decrease or increase brightness and power consumption.
Description of Power Save Modes
ON
OFF
Select “Power Save” in the “Options (1)” menu For settings, see page 36.
Quantity of light is 80%. Power consumption is 250W.
Quantity of light is 100%. Power consumption is 290W.
Note
Power Save mode is factory preset toOFF”.

Automatic Power Shutoff Function

When no input signal is detected for more than 15 minutes, the projector will automatically shut off if set to The Auto Power Off function will be disabled when it has been set to
Select “Auto Power Off” in the Options (1) menu For settings, see page 36.
Note
When the Auto Power Off function is set to
(On), 5 minutes before the power turns off, the message Power OFF in X min.” will appear on the screen to indicate the remaining minutes.
(On)”.
(Off)”.
52
-52

Activating the sRGB Color Management Function

This function calibrates the projector’s output to conform to sRGB standard (6,500K).
Setting the Color Manage­ment Function (sRGB)
Select “sRGB” in the “Options (1)” menu For settings, see page 36.
Note
When setting sRGB to “ON, the pro- jected image may become dark; however, this does not indicate a malfunction. For additional information about sRGB
function, please visit http://www.srgb.com/”.
Info
When sRGB is set to “ON”;
The gamma correction cannot be set.
Red”, “Blue or CLR Temp in Picture
cannot be adjusted.

Auto Search Function

This function automatically searches for and switches to the input mode in which signals are being received, when the projector is turned on, or when the INPUT button is pressed.
Using Auto Search
Select Auto Search” in the Options (1)” menu For settings, see page 36.
Note
ON Automatically switches to the input mode in which signals are being received, when turning on the projector or pressing
on the projector.
OFF For switching input modes manually in order by pressing
To stop searching for the input mode, press
Info
Even while this function is searching for input signals, whenever
mote control is pressed, the input mode is switched to the respective one.
Even while the function is searching for input signals, pressing any buttons besides
and
on the projector, or ,
on the remote control.
returns to the previous input mode.
on the projector.
,
or
on the re-
or
,
Easy to Use Functions
-53

Video Digital Noise Reduction (DNR) System

Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Reducing Image Noise (DNR)
Select “DNR” in the “Options (1)” menu For settings, see page 38.
Note
Set a level so as to view a clearer picture.
Make sure to set DNR to “OFF” in the fol­lowing cases:
When the image is blurry.
When the contours and colors of moving
images drag.
When TV broadcasts with weak signals are projected.
Info
This function is available with INPUT 1 (480
I and 480P signals) and INPUT 2, 3
(all signals).
Setting the On-screen Display
This function allows you to turn on or off the on-screen messages. When setting Level A” or Level B” in “OSD Display”, the input mode display (e.g. INPUT 1) will not appear, even if the INPUT button is pressed.
Selected Item
Normal
Level A
Level B
All On-screen Displays are displayed.
Input/Freeze/Enlarge/Auto Sync/Volume/AV Mute are not displayed.
All On-screen Displays are not displayed. (except Menu, On-screen displays displayed when the LENS button is pressed and warning displays (Power off/Temp./Lamp, etc.))
Turning Off the On-screen Display
Description
Select OSD Display in the “Options (1)” menu For settings, see page 38.
54
-54

Setting the Video Signal

The video input system mode is preset to “Auto”; however, a clear picture from the con- nected audio-visual equipment may not be received, depending on the video signal differ­ence. In that case, switch the video signal.
Setting the Video Signal
Select Video System” in the Options (1)” menu For settings, see page 38.
Note
The video signal can only be set in IN­PUT 2 or INPUT 3 mode.
In “Auto, images are displayed in PAL even if PAL-N or PAL-M input signals are received.
PA L SECAM
NTSC4.43
NTSC3.58
When connected to PAL video equipment. When connected to SECAM video
equipment. When reproducing NTSC signals in
PAL video equipment. When connected to NTSC video equipment.
Easy to Use Functions
-55

Saving Projected Images

This projector allows you to capture projected images (RGB signals) and set them as a startup image, or background image when no signals are being received.
You can capture the images that are input using analog RGB signals and Digital DVI XGA signals.

Capturing the Image

Select “Image Capture” in the “Options (1)” menu For details, see page 38.
1 Press
Save Image” and press
The projected image is captured. It may take some time for capturing.
11
2
1 Press
11
Yes”.
22
2 Press
22
Note
This function only works in 1024 x 768 (XGA) with the exception of 43 Hz vertical which is a interlaced signal.
The saved image is reduced to 256 col­ors.
Images from equipment connected to IN­PUT 2 or INPUT 3 cannot be captured.
or
or
.
to select
to select

Deleting the Captured Image

.
1 Select Delete” and press
.
11
2
56
-56
1 Press
11
OK”.
22
2 Press
22
or
.
to select

Setting a Background Image

This function allows you to select the image displayed when no signal is being sent to the projector.
Selected Item
Sharp
Custom
Blue
None
*1 You can set a captured image as a background image in Image Capture”. *2 If the input signal has interference, the screen will be displayed with the interference.
*1
SHARP default image
User customized image (i.e. company logo)
Blue screen
Black screen
*2
Description
Selecting a Background Image
Select Background” in the Options (1)” menu For settings, see page 38.
Note
When “Custom is selected, an image saved using Image Capture” can be dis- played as a background image. A “Custom” image is preset as a black screen.
Selecting a Startup Image
This function allows you to specify the image to be displayed upon the projector’s startup.
Selected Item
Sharp
Custom *
None
* You can set a captured image as a startup image by selecting "Custom".
SHARP default image
User customized image (i.e. company logo)
Black screen

Selecting a Startup Image

Select Startup Image” in the Options (1)” menu For settings, see page 38.
Note
When “Custom is selected, an image saved using Image Capture” can be dis- played as a startup image. A “Custom” image is preset as a black screen.
Description
Easy to Use Functions
-57

Using an RGB Monitor Loop-out Adaptor

Using an RGB monitor loop-out adaptor (sold separately) and an RGB cable (commercially available), be sure to set to Yes (Y Cable)” when you want to display computer images both on the projector and on a monitor.
Using a RGB Monitor Loop-out Adaptor
Select “Monitor Out” in the “Options (1)” menu For settings, see page 38.
Note
Be sure to set to Disable when not using an RGB monitor loop-out adaptor.
If the setting is not correct, the image may be dark, too bright or whitish. This does not indicate malfunction.
Make sure to set to when using the RGB monitor loop-out adaptor.
Yes (Y Cable)

Displaying the Lamp Usage Time

Confirming the Lamp Usage Time
This function allows you to check the lamp us­age time.
Select Options (2) menu to see the lamp usage time.
Note
It is recommended that the lamp be changed after approximately 1,900 cumu­lative hours of use. For lamp replacement, contact your near­est Sharp Authorized Projector Dealer or Service Center.
58
-58
Lamp Usage Time

Displaying the Break Timer

Displaying and Setting the Break Timer
Select “Break Timer” from the “Options (2)” menu For details, see page 36.
1 When
or
is displayed, press
to set the Break
Timer.
You can set anywhere between 1 and 60 minutes (in 1 minute units).
2 Press
to cancel the Break
Timer.
Note
Auto Power Off will be temporarily dis­abled during the Break Timer. If no signal transmission occurs for more than 15 minutes after the Break Timer has completed, the projector will turn off.
The Break Timer will be displayed on the startup image. To change the screen dis­played during the Break Timer, change the setting of “Startup Image” (see page
57).
"On-screen Display
Easy to Use Functions
-59

Reversing/Inverting Projected Images

This projector is equipped with a reserve/invert image function that allows you to reverse or invert the projected image for various applications.
Selected Item
Front
Ceiling + Front
Rear
Ceiling + Rear
Normal image
Inverted image
Reversed image
Reversed and inverted image
Setting the Projection Mode
Select PRJ Mode in the Options (2) menu For settings, see page 38.
Note
If a password has been set, the password input box will be displayed when select­ing the PRJ Mode”.
This function is used for the reversed im­age and ceiling-mount setups. See page
19 for these setups.
Description
Front Ceiling+Front Rear Ceiling+Rear

Locking the Operation Buttons on the Projector

This function can be used to lock the use of certain operation buttons on the projector. The following are the three keylock levels.
Keylock Level
Normal
Level A
Level B
All operation buttons are functional.
Only INPUT/VOLUME/AV MUTE buttons on the projector are available.
All operation buttons on the projector are unavailable.

Setting up the Keylock

Select Keylock Level in the Options (2) menu For settings, see page 38.
Note
If a password has been set, the password input box will be displayed when select­ing the Keylock Level”.
-60
Description

Canceling the Keylock Setting

When the Keylock Level is set to Normal”, all buttons are functional.
Select Keylock Level” in the Options (2) menu and set settings, see page 38.
Note
When a password has been set, and Keylock Level is selected, the password input box will be displayed.
If both a password and the Keylock Level have been set at the same time, the pass­word will be necessary before changing the Keylock Level.
Normal
. For

Setting up a Password

A password can be set by the user to prevent adjustments to certain settings on the Options (2) menu. Using a password together with the Keylock Level (page 60) is more effective.

Entering the Password

Select Password” in the Options (2) menu For details, see page 38.
1 Press
or
to select the
desired number and then press
.
2 Enter the 3 remaining digits
and press
.
3 Enter the password again in
Reconfirm and press
Note
When a password is set, you need to enter the password to change PRJ Mode, Keylock Level, “Anti- Theft and All Reset settings.
.
Easy to Use Functions
-61

Setting the Anti-Theft

The anti-theft function prevents unauthorized use of the projector. You can choose to use this function or not. If you do not want to use this function, just do not enter the keycode. Once the theft-deterrent function is activated, users will need to enter the correct keycode each time the projector is started. Failure to enter the correct keycode will prevent images from being projected. The following procedures explain how to use this function.
Entering the Keycode
Anti-Theft cannot be selected unlessPassword is set. (See page 61.)
When “Anti-Theft is selected, the password input box will appear. Enter the keycode af­ter the right password is entered.
Select Anti-Theft in the Options (2) menu For details, see page 38.
1 Press any button you like on
the remote control or projec­tor to set the first digit in “New Code”.
Note
The following buttons on the remote control and projector cannot be set as keycodes:
POWER button
ENTER button
UNDO button
MENU button
FORWARD button
BACK button
2 Enter the remaining 3 digits by
pressing any buttons you like.
3 Enter the same keycode once
more in “Reconfirm”.
Easy to Use Functions
Note
The Keylock function will become temporarily disabled.
-63
Setting the Anti-Theft (cont.)
When Anti-Theft is set, the keycode inputting section appears after the power is turned on. At that time, enter the right keycode.
Press the buttons on the remote control if the buttons on the remote control are used for setting the keycode. In the same manner, press the buttons on the projector if the buttons on the projector are used for setting the keycode.
Info
Once the function is activated, you must
remember the correct keycode. We suggest you record the keycode in a safe place where only authorized users will have access. If you lose or forget your keycode, you will need to contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 78). You may need to bring your projector to them to restore the projector to original factory condition (password and keycode reset).

Changing the Keycode

When “Anti-Theft is selected, the password input box is displayed. After the password has been entered, you can change the keycode.
Select “Anti-Theft” in the “Options (2)” menu For details, see page 38.
1 Press the buttons on the
remote control or the projector to enter the preset 4-digit keycode in “Old Code”.
2
Press any button you like on the remote control or the projector to enter the new keycode.
3 Enter the same 4-digit keycode
in “Reconfirm”.
Note
If you do not want to set a keycode, leave
the keycode field blank in steps 2 and 3 and press
.
-64

Initializing the Settings

This function allows you to initialize the settings you have made in the projector.
Returning to the Default Settings
Select All Reset in the Options (2) menu For resetting, see page 36.
Note
If a password has been set, the pass-
word input box will be displayed when selecting All Reset”.
The following items cannot be initialized.
Fine Sync
Special Modes
Signal Info
Options
Lamp Timer
Anti-Theft
Language
Image stored using Image Capture
Easy to Use Functions
-65

Displaying the Adjustment Settings

This function can be used to display all the adjusted settings as a list on the screen.
Checking the Adjustment Settings on a List
Select the “Status” menu and press
For details, see page 36.
-66

Appendix

Appendix

Carrying the Projector

How to Use the Carrying Case
When carrying the projector, attach the lens cap to the lens, and place it in the included carrying case.
1 Open the cover of the carrying
case.
2 Remove the inner padding
from the carrying case, and fold it in the direction of the arrows.
3 Reinsert the inner padding into
the carrying case.
Info
Be sure to insert the inner padding to protect the lens and the projector.
4 Place the projector and the ac-
cessories in the carrying case.
Info
Be sure to attach the lens cap to protect the lens.
Be sure the projector has cooled down enough before placing it in the case.
Info
This carrying case is only for storing and carrying the projector.
Sending the projector in the carrying case as a parcel may cause damage to the projector. If you send the projector in the carrying case as a parcel, be sure to place it in a sturdy case and with enough shock absorbing material to avoid any damage.
Do not expose the carrying case or pro­jector to direct sunlight, near heat sources, or leave them in a car. The car­rying case or projector may change color or become deformed.
Lens cap
Adjust the shoulder strap.
-68

Maintenance

Cleaning the projector
Be sure to unplug the power cord before clean­ing the projector.
The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items on the pro­jector for long time.
The effects of some of the agents in the plastic
may cause damage to the quality or finish of the projector.
Thinner
Wax
Wipe off dirt gently with a soft flannel cloth.
N
e
u
tra
l d
e
te
rg
e
n
t
Cleaning the lens
Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coat­ing film on the surface of the lens.
As the surface of the lens can easily get dam­aged, be sure not to scrape or hit the lens.
Cleaning
Paper
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Projector’s Rear View
Neutral detergent diluted with water
When the dirt is hard to remove, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before using.
Appendix
-69

Maintenance Indicators

The warning lights on the projector indicate problems inside the projector.
If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT
indicator will illuminate red, and the power will turn off. After the power has been turned off, follow the procedures given below.
POWER
indicator
About the TEMPERATURE WARNING indicator
If the temperature inside the projector in­creases, due to blockage of the air vents, or the setting location, will blink in the lower left corner of the picture. If the tem­perature keeps on rising, the lamp will turn off and the TEMPERATURE WARNING in­dicator will blink, the cooling fan will run for further 90 seconds, then the power will be shut off. After perform the following measures.
Maintenance indicator Condition Problem Possible Solution
Normal Abnormal
TEMPERA-
TURE
WARNING
indicator
Green on
LAMP
REPLACE-
MENT
indicator
Green
blinks
when the
lamp is
active.
appears, be sure to
Abnormal
Off
Red on/ Power off
Red blinks
Red on/ Power off
The internal temperature is abnormally high.
Time to change the lamp
The lamp does not illuminate.
TEMPERATURE WARNING indicator
LAMP REPLACEMENT indicator
Blocked air intake
Cooling fan break-
down
Internal circuit failure
Clogged air intake
Lamp usage time
exceeded 1,900 hours
Burnt-out lamp
Lamp circuit failure
About the LAMP REPLACEMENT indicator
When the lamp exceeds 1,900 cumulative hours of use, will be displayed on the screen in yellow. When the cumulative hours of use reach 2,000, change to red, the lamp will au­tomatically turn off and then the projector as well. At this time, the LAMP REPLACEMENT indica­tor will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
Relocate the projector to an area with proper ventilation.
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 78) for repair.
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 78) for repair or lamp replacement.
Please exercise care when replacing the lamp.
will
Info
If the TEMPERATURE WARNING indicator illuminates, and the power turns off, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.)
If the power is turned off and then turned on again, as during a brief test, the LAMP REPLACEMENT indica­tor may be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and plug it back in again.
If you want to clean the air vents during projector operation, be sure to first press
and after the power has
turned off and the cooling fan has stopped, then clean the vents.
Do not unplug the power cord after the power has been turned off and while the cooling fan is running. The cooling fan runs for about 90 seconds.
-70

Regarding the Lamp

Lamp

It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative
hours of use or when you notice a significant deterioration of the picture and color quality. The lamp usage time can be checked with the on-screen display. See page 58.
For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service
Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho­rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Caution Concerning the Lamp

This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.
When the LAMP REPLACEMENT indicator and on-screen display icon are illuminated or flash, it is
recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult with a doctor as soon as possible.
Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to remove the damaged lamp and assure safe operation.
U.S.A. ONLY

Replacing the Lamp

Caution
Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury.
Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.
If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho-
rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC­PGM20X//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully change the lamp by following the instructions described in this section. If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.
Appendix
-71
Regarding the Lamp (cont.)
Removing and Install­ing the Lamp Unit
Info
Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector.
To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
Do not remove other screws except for the lamp cover screws.
Please refer to the installation manual included with the lamp unit.
1 Press on the projector to
turn off the power.
Wait until the cooling fan stops.
Lamp unit
BQC-PGM20X//1
POWER button
2 Disconnect the power cord.
Unplug the power cord from the AC socket.
Leave the lamp until it has fully cooled down (about 1 hour).
3 Remove the lamp unit cover.
Turn over the projector, and loosen the user service screw that secures the lamp unit cover. Then slide the cover in the direction of the arrow.
-72
AC socket
User service screw
4 Remove the lamp unit.
Remove the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow.
5 Insert the new lamp unit.
Press the lamp unit firmly into the lamp unit compartment. Fasten the secur­ing screws.
6 Attach the lamp unit cover.
Slide the lamp unit cover in the direc­tion of the arrow. Then tighten the user service screw.
Info
If the lamp unit is not correctly installed, the power will not turn on, even if the power cord is connected to the projector.
Securing screw

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.
1 Connect the power cord.
Plug the power cord into the AC socket of the projector.
2 Reset the lamp timer.
While pressing simultaneously
, , and on the projec-
tor, press
“LAMP 0000H is displayed, indicating that the lamp timer is reset.
Info
Make sure to reset the lamp timer only when replacing the lamp. Otherwise, this may cause the lamp to become damaged or explode.
on the projector.
User service screw
AC socket
POWER button
buttons
Appendix
ENTER button
-73

Connecting Pin Assignments

DVI Digital / Analog INPUT 1 port : 29 pin connector
DVI Digital INPUT
•••••••••
9
••••
21
17
••••
18 23
~
~
~
•••••••••
••••
••••
16
87
C1 C2
C4
C5 C3
24
Pin No. Signal Pin No. Signal
1 T.M.D.S data 2– 16 Hot plug detection 2 T.M.D.S data 2+ 17 T.M.D.S data 0– 3 T.M.D.S data 2 shield 18 T.M.D.S data 0+ 4 Not connected 19 T.M.D.S data 0 shield 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 T.M.D.S clock shield 8 Not connected 23 T.M.D.S clock+
9 T.M.D.S data 1– 24 T.M.D.S clock– 10 T.M.D.S data 1+ C1 Not connected 11 T.M.D.S data 1 shield C2 Not connected 12 Not connected C3 Not connected 13 Not connected C4 Not connected 14 +5V power C5 Ground 15 Ground
DVI Analog RGB Input
Pin No. Signal Pin No. Signal
1 Not connected 16 Hot plug detection 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 DDC clock 21 Not connected 7 DDC data 22 Not connected 8 Vertical sync 23 Not connected
9 Not connected 24 Not connected 10 Not connected C1 Analog input Red 11 Not connected C2 Analog input Green 12 Not connected C3 Analog input Blue 13 Not connected C4 Horizontal sync 14 +5V power C5 Ground 15 Ground
4-pin USB connector
12
USB connector: 4 pin B-type USB connector
Pin no. Signal Name
1 VCC USB power 2 USB– USB data– 3 USB+ USB data+ 4 SG Signal Ground
DVI Analog Component Input
Pin No. Signal Pin No. Signal
1 Not connected 16 Not connected 2 Not connected 17 Not connected 3 Not connected 18 Not connected 4 Not connected 19 Not connected 5 Not connected 20 Not connected 6 Not connected 21 Not connected 7 Not connected 22 Not connected 8 Not connected 23 Not connected
9 Not connected 24 Not connected 10 Not connected C1 Analog input Pr/Cr 11 Not connected C2 Analog input Y 12 Not connected C3 Analog input Pb/Cb 13 Not connected C4 Not connected 14 Not connected C5 Ground 15 Ground
-74
43

Computer Compatibility Chart

Multiple signal support Horizontal Frequency: 15–126 kHz Vertical Frequency: 43–200 Hz* Pixel Clock: 12–230 MHz
Compatible with sync on green and composite sync signals
UXGA and SXGA compatible in advanced intelligent compression
AICS (Advanced Intelligent Compression and Expansion System) resizing technology
The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
PC/ MAC/ WS
PC
VGA
SVGA
XGA
Resolution
640 × 350
720 × 350
640 × 400
720 × 400
640 × 480
800 × 600
1,024 × 768
Horizontal
Frequency
(kHz)
27.0 60
31.5
37.9
27.0
31.5
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
47.9
53.0
61.8
78.5
80.9
100.4
31.4
35.1
37.9
44.5
48.1
46.9
53.7
56.8
64.0
77.2
98.3
102.1
125.6
35.5
40.3
48.4
56.5
58.1
60.0
68.7
73.5
77.2
80.6
98.8
113.2
Vertical
Frequency
(Hz)
70 85 60 70 60 70 85 60
70 85 50 60 70 72 75 85 90
100 120 150 160 200
50 56 60 70 72 75 85 90
100 120 150 160 200
43 50 60 70 72 75 85 90 96
100 120 140
DVI
VESA
Supp-
Stan-
ort
dard
✔ ✔ ✔
✔ ✔ ✔
✔✔ ✔
✔ ✔✔
Display
Upscale
Tr ue
PC/ MAC/ WS
PC
PC/
MAC 13
PC/
MAC 19
PC/
MAC 21
MAC
16 MAC 21 HP (WS) PC (WS)
WS
SGI (WS)
SUN (WS)
Resolution
1,152 × 864
SXGA
1,152 × 882
1,280
×
1,024
+
SXGA
1,400 ×1,050
UXGA
SXGA
SVGA
SXGA
SXGA
1,600
×
1,200
VGA
640 × 480 34.9 67
XGA
1,024 × 768
1,280×1,024
832
×
624
1,152
×
870
1,280×1,024
1,280
×
960
1,280×1,024
1,152
×
900
Horizontal
Frequency
Vertical
Frequency
(kHz)
54.3
64.0
64.1
67.5
75.7 80
77.3
90.2
54.8
65.9
67.4
64.0
74.6
78.1 74
80.0 75
91.1 85
108.4 100
64.0 60
74.7 52
75.0 60
81.3 65
87.5 70
90.1 72
93.8 75
106.3 85
48.4 60 ✔✔
60.0 75 ✔✔
80.0 75
46.8 75
49.6 75
68.5 75
78.1 72
60.0 60
85.9 85
53.5 50
76.8 72
60.9 66
71.9 76
(Hz)
100
60 70 72 75
85
60 72 74 60 70
VESA Stan­dard
✔ ✔
DVI Supp­ort
Compression
Compression
Compression
Compression
Display
Advanced Intelligent
Intelligent
Upscale
Tr u e
Advanced
Intelligent
Upscale
Advanced Intelligent
* Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated.
Note
This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual.
When this projector receives 640 × 350 VESA format VGA signals, 640 × 400 appears on the screen.
When receiving 1,600 × 1,200 VESA format signals, sampling occurs and part of the image may be cut as the image is
displayed in 1,024 lines.
Appendix
-75

Troubleshooting

Problem
No picture and no sound
Sound is heard but no
picture appears
Color is faded or poor
Picture is blurred;
noise appears
Check
Projector power cord is not plugged into the wall outlet.
Power to the external connected devices is off.
The selected input mode is wrong.
Cables incorrectly connected to side panel of the projector.
Remote control batteries have run out.
External output has not been set when connecting notebook computer.
The AV MUTE display appears.
Cables incorrectly connected to the side panel of the projector.
“Bright” is set to minimum position.
Picture adjustments are incorrectly set.
(Video Input only)
Video input system is incorrectly set. (INPUT 1 only)
Input signal type RGB/Component is incorrectly set.
Adjust the focus.
The projection distance exceeds the focus range.
(Computer Input only)
Perform “Fine Sync” Adjustments (“Clock” Adjustment)
Perform “Fine Sync” Adjustments (“Phase” Adjustment)
Noise will appear depending on the computer.
The “DNR” (Digital Noise Reduction) setting is not correct.
Cables incorrectly connected to side panel of projector.
Volume is set to minimum.
Page
20
29
21–26
13
30
21–26
40
40
55
40
31
17–18
42·44
42
54
21–26
29
Picture appears but no
sound is heard
An unusual sound is
occasionally heard
from the cabinet
Maintenance
indicator illuminates
Image cannot be
captured
Pict in Pict does not
work
-76
If the picture is normal, the sound is due to cabinet shrinkage caused by a room temperature changes. This will not affect operation or performance.
See “Maintenance Indicators”.
The signal in INPUT 1 is not an analog RGB/Digital RGB XGA
(1024 × 768) signal. Images cannot be captured if the signals are different from the above.
The signal in INPUT 1 is set to a resolution that exceeds SXGA.
The signal in INPUT 1 is sending Component signals 480I,
480P, 720P, or 1080I.
The signal in INPUT 1 is set to interlace mode using RGB signals.
70
56
51
Power cannot be turned
on or off using the
POWER button on the
projector
Picture is green on
INPUT 1 COMPONENT
Picture is pink (no green)
on INPUT 1 RGB
Picture is dark
Picture is too bright and
whitish
The VOLUME buttons
on the projector do not
work
CheckProblem Page
The Keylock level is set. If the Keylock level is set to Level B, all the buttons are locked. If the Keylock level is set to Level A, only the INPUT, VOLUME and AV MUTE buttons work.
Change the input signal type setting.
The LAMP REPLACEMENT indicator is blinking in red. Replace
the lamp.
“Monitor Out is set to Disable when the RGB monitor loop-out adaptor is connected to Monitor Out.
“Monitor Out is set to “Yes (Y Cable) when the RGB monitor loop-out adaptor is not connected to Monitor Out.
Picture adjustments are incorrectly set.
The VOLUME buttons do not work when: (try the VOL+/– on the remote control)
when the menu is displayed
when the lens menu is displayed
when Pict in Pict is working
during Enlarge (More than double size)
a dot by dot screen resolution larger the panel resolution.
60
40
72·73
58
58
40
-77
Appendix

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 76 and 77. If this operation manual does not answer your question, please contact the SHARP Service departments listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharplcd.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140 http://www.sharp.ca
Mexico Sharp Electronics Corporation Mexico Branch
(525) 716-9000 http://www.sharp.com.mx
Germany Sharp Electronics (Europe) GMBH
01805-234675 http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
0161-205-2333 custinfo@sharp-uk.co.uk http://www.sharp.co.uk
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1 http://www.sharp.it
Australia Sharp Corporation of Australia Pty. Ltd.
1300-135-022 http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972 http://www.sharpnz.co.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311 helpdesk@smef.global.sharp.co.jp
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com
Korea Sharp Electronics Incorporated of Korea
(82) 2-3660-2002 webmaster@sharp-korea.co.kr http://www.sharp-korea.co.kr
-78

Specifications

Product type
Video system
Display method
DMD panel
Projection lamp
Component input signal
(INPUT1)
Horizontal resolution
Computer RGB input signal
(INPUT 1)
S-video input signal
(INPUT 2)
Video input signal
(INPUT 3)
Pixel clock
Vertical frequency
Horizontal frequency
Audio input signal
Audio output
Speaker system
Rated voltage
Input current
Rated frequency
Power consumption
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
* Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated.
Digital Multimedia Projector PG-M20X
Model
NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/ DTV480I/DTV480P/DTV720P/DTV1080I Single Chip Digital Micromirror Device™ (DMD™) by Texas Instruments Panel size: 0.7" (17.8 mm), 1 chip XGA DMD No. of dots: 786,432 dots (1,024 [H] × 768 [V]) 1–1.2 × zoom lens, F1.75–2.04, f = 28.0–33.5 mm
Lens
High Intensity Discharge Lamp (HID Lamp), DC 210 W 29-pin connector DVI input signal: Digital 250–1,000 mV 50
Y: 1.0 Vp-p, sync negative, 75 terminated PB: 0.7 Vp-p, 75 terminated PR: 0.7 Vp-p, 75 terminated 700 TV lines (DTV720P) 29-pin connector RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. SIGNAL: Same as above 4-pin Mini DIN connector Y (luminance signal): 1.0 Vp-p, sync negative, 75 terminated C (chrominance signal): Burst 0.286 Vp-p, 75 terminated RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 terminated 12–230 MHz 43–200 Hz* 15–126 kHz ø3.5 mm MINIJACK: AUDIO, 0.5 Vrms, more than 47 k (stereo)
2.0 W (monaural) 4 cm × 3 cm AC 100–240 V
3.2 A 50/60 Hz 290 W 1,090 BTU/hour 41°F to 95°F (+5°C to +35°C) –4°F to 140°F (–20°C to +60°C) Plastic 38 kHz 8 5⁄8" × 3" × 11 15⁄16" (219 (W) × 76 (H) × 303 (D) mm) (main body only) 8 3⁄4" × 3 1⁄4" × 12 1⁄2" (223 (W) × 83 (H) × 318 (D) mm) (including adjustment feet and projecting parts)
5.8 lbs. (2.6 kg) Remote control, Two R-03 batteries, Power cord for U.S., Canada etc. (6', 1.8 m), Power cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong and Singapore (6',
1.8 m), Power cord for Australia, New Zealand and Oceania (6', 1.8 m), DVI to 15-pin D-sub cable (6', 1.8 m), USB cable (6', 1.8 m), Carrying case, Lens cap (attached), Lens cap strap, Terminal cover (attached), CD-ROM, Operation manual, Quick reference guides Lamp unit (Lamp/cage module) (BQC-PGM20X//1), Remote control (RRMCGA013WJSA), Two R-03 batteries (AAA size, UM/SUM-4, HP-16, or similar), Power cord for U.S., Canada etc. (QACCDA007WJPZ), Power cord for Europe, except U.K. (QACCV4002CEZZ), Power cord for U.K., Hong Kong and Singapore (QACCB5024CENA), Power cord for Australia, New Zealand and Oceania (QACCL3022CEZZ), DVI to 15-pin D-sub cable (QCNWGA010WJZZ), USB cable (QCNWG0001WJPZ), Carrying case (GCASN0005CESA), Lens cap (CCAPHA001WJ01), Lens cap strap (UBNDT0013CEZZ), Terminal cover (GCOVD0103CESA), CD-ROM (UDSKA0058CEN2), Operation manual (TINS-7609CEN1), Quick reference guides
Analog 0.7 Vp-p 75
Appendix
This SHARP projector uses a DMD panel. This very sophis­ticated panel contains 786,432 pixels. As with any high tech­nology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.
Specifications are subject to change without notice.
This unit has some inactive pixels within acceptable toler­ances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
-79

Dimensions

Units: inches (mm)
Side View Side ViewTop View
9
12
(318.3)
Rear View
11 15/
/
16
3
/4 (223)
8
5
8
/8 (219)
1
/16 (128)
5
(302.5)
16
Bottom View
Front View
1
/
8
3 (80)
1
(34.2)
5
/
(7.5)
1
4
(104)
1
1
/
2
3
/
8
9
4
/16 (115.5)
11
7
/16 (195)
1
3
/4 (82.5)
3
2
2 3/16 (55.5)
16
/
8
(60)
/8
(38.7)
10 (261.5)
5
/
16
3
(76.1)
1
3
(82.9)
/
4
-80

Glossary

Advanced intelligent compression
High quality resizing of lower and higher resolu­tion images to fit the projectors native resolution.
Anti-theft
In case the projector is stolen, this function dis­ables projection of images if the correct keycode is not entered.
Aspect Ratio
Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9.
Auto Sync
Optimizes projected computer images by auto­matically adjusting certain characteristics.
Background
Initial setting image projected when no signal is being output.
Border
Projects a 4:3 image fully within a 16:9 screen by keeping the aspect ratio at 4:3.
Clock
Clock adjustment is used to adjust vertical noise when clock level is incorrect.
CLR Temp (Color temperature)
Function that can be used to adjust the color tem­perature to suit the type of image input to the pro­jector. Decrease the color temperature to create warmer, reddish images for natural flesh tones, or increase to create cooler, bluish images for a brighter picture.
Digital Shift
Shifts image up or down easily by
tons when RESIZE mode of input image is BOR­DER, STRETCH or SMART STRETCH of the video or the DTV signals.
,
Dot by dot
Mode that projects images in their native resolution.
DVI (Digital Visual Interface)
Display digital interface that also supports Ana­log interfaces.
Freeze
Temporarily freezes a moving image.
GAMMA
Image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. You can select four different modes: STANDARD, PRESENTATION, CINEMA and GAME.
Keylock Level
Mode that can lock the operation of projector but­tons to prevent mischief.
but-
Keystone correction
Function to digitally correct a distorted image when the projector is set up at an angle, smoothens out jaggies on keystone images and compresses the image not only horizontally but vertically keeping the 4:3 aspect ratio.
Password
A password is set so that changes cannot be made in the settings of the Options (2) menu.
Phase
Phase shift is a timing shift between isomorphic signals with the same resolution. When phase level is incorrect, the projected image typically displays horizontal flicker.
Picture in Picture
Allows you to add video images onto a data screen image, providing you with even more effective pre­sentations.
Progressive Mode
The progressive display projects a smoother video image. You can select three different modes: 2D Progressive, 3D Progressive and Film Mode.
RESIZE
Allows you to modify or customize the picture dis­play mode to enhance the input image. You can select six different modes: NORMAL, FULL, DOT BY DOT, BORDER, STRETCH and SMART STRETCH.
Smart Stretch
Projects the image fully in a 16:9 screen by en­larging only the surrounding areas while keeping the aspect ratio in the middle part of the image at 4:3.
sRGB
An international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the color changes according to DLP features, so that the images are displayed in a natural tint based on an original image, when switching to the sRGB mode.
Startup Image
The image displayed when the projector is turned on.
Status function
Displays the settings of each adjustment item.
Stretch
Mode that stretches the 4:3 image horizontally to display it fully on a 16:9 screen.
Appendix
-81

Index

2D Progressive .................................................... 41
3D Progressive .................................................... 41
AC socket ............................................................ 20
Adjustment buttons .............................................. 36
Adjustment feet .................................................... 16
All Reset .............................................................. 65
Anti-Theft ............................................................. 63
Aspect ratio .......................................................... 47
Auto Power Off .................................................... 52
Auto Search ......................................................... 53
Auto Sync adjustment.......................................... 44
AUTO SYNC button ............................................. 44
Auto Sync Display ............................................... 44
AV MUTE button .................................................. 30
BACK button ........................................................ 26
Background image............................................... 57
Batteries............................................................... 13
BORDER.............................................................. 47
Carrying case....................................................... 68
Ceiling-mount....................................................... 19
Clock .................................................................... 42
CLR Temp (Color Temperature) .......................... 40
Component input ................................................. 23
Computer images adjustment ............................. 42
Digital Shift........................................................... 33
DNR ..................................................................... 54
DOT BY DOT ....................................................... 47
DVI to 15-pin D-sub cable ................................... 21
ENLARGE buttons............................................... 49
ENTER button...................................................... 36
Exhaust vent ........................................................ 69
Film Mode ............................................................ 41
Fine Sync ............................................................. 42
Focus ring ............................................................ 31
Foot releases ....................................................... 16
FORWARD button ............................................... 26
FREEZE button.................................................... 48
FULL .................................................................... 47
GAMMA button .................................................... 50
Image Capture ..................................................... 56
INPUT 1 terminal ................................................. 21
INPUT 1 – 3 modes ............................................. 29
INPUT 2 terminal ................................................. 24
INPUT 3 terminal ................................................. 24
INPUT AUDIO terminal ........................................ 21
INPUT button ....................................................... 29
Intake vent ........................................................... 69
Kensington Security Standard connector............ 11
Keylock level ........................................................ 60
Keystone correction (adjustment) ....................... 32
Lamp .................................................................... 71
LAMP REPLACEMENT indicator ........................ 70
Lamp Timer .......................................................... 58
Language selection ............................................. 30
Lens adjustment .................................................. 31
LENS button ........................................................ 32
Lens cap .............................................................. 68
Lens cap strap ..................................................... 11
MENU button ....................................................... 36
Monitor Out .......................................................... 58
NORMAL.............................................................. 47
Optional accessories ........................................... 14
OSD Display (On-screen display) ....................... 54
Password ............................................................. 61
PDF ........................................................................ 9
Phase ................................................................... 42
Pict in Pict ............................................................ 51
Picture adjustments ............................................. 40
POWER button .................................................... 28
Power cord........................................................... 20
POWER indicator................................................. 28
Power Save Mode ............................................... 52
PRJ mode ............................................................ 60
Progressive Mode................................................ 41
Remote control .................................................... 12
Remote control sensor ........................................ 13
Remote control signal transmitter ....................... 12
Replacing the lamp .............................................. 71
RESIZE button ..................................................... 46
Reversing/Inverting Images................................. 60
Save Setting ........................................................ 42
Select Setting....................................................... 43
Signal Info ............................................................ 43
Signal Type .......................................................... 40
SMART STRETCH .............................................. 47
Speaker................................................................ 29
Special Mode adjustment .................................... 43
sRGB ................................................................... 53
Startup image ...................................................... 57
Status ................................................................... 66
STRETCH ............................................................ 47
Supplied accessories........................................... 14
TEMPERATURE WARNING indicator................. 70
Terminal cover ..................................................... 10
UNDO button ....................................................... 33
USB cable ............................................................ 26
USB port .............................................................. 26
Video System....................................................... 55
VOLUME buttons ................................................. 29
Wireless Presentation.......................................... 26
Zoom knob ........................................................... 31
-82
SHARP CORPORATION
Loading...