Sharp Notevision PG-D2870W, Notevision PG-D3050W, Notevision PG-D3550W Operation Manual

Page 1
Introduction
Easy Start
Setup
Connections
Basic
Operation
Useful
Appendix
OPERATION MANUAL
DATA PROJECTOR
MODEL
PG-D3550W PG-D3050W PG-D2870W
PG-D3550W/PG-D3050W
Page 2
ii
IMPORTANT
• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information.
• Before recycling the packag ing, please ensure that you have checked the con­tents of the carton thoroughly against the list of “Supplied accessories” on page
11.
Model No.:
Serial No.:
Page 3
iii
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fi tted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked
or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refi t the fuse cover after replacing the fuse. Never use the plug without the fuse cover fi tted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fi t an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi­ately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious electric shock may occur. To fi t an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth Blue : Neutral
Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
x
The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol
or coloured green
or green-and-yellow.
x
The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black.
x
The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
Page 4
iv
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese, Korean and Arabic. Carefully read through the operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch, Koreanisch und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, espagnol, italien, néerlandais, suédois, portugais, chinois, coréen et arabe. Veuillez lire at­tentivement ces instructions avant de faire fonctionner le projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español, italiano, holandés, sueco, portugués, chino, coreano y árabe. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano, olandese, svedese, portoghese, cinese, coreano e arabo. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans, Italiaans, Nederlands, Zweeds, Portugees, Chinees, Koreaans en Arabisch. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska, koreanska och arabiska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano, Holandês, Sueco, Português, Chinês, Coreano e Árabe. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.
Page 5
1
Introduction
Before using the projector, please read this operation manual carefully.
Introduction
ENGLISH
There are two important reasons for prompt warranty registration of your new SHARP Projec tor, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefi t of the parts, service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notifi cation of inspection, modifi cation, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verifi cation.
U.S.A. ONLY
WARNING:
FCC Regulations state that any unauthorized changes or modifi cations to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equip ment.
U.S.A. ONLY
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
The lightning fl ash with arrowhead sym­bol, within an equilateral triangle, is in­tended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of suffi cient magnitude to constitute a risk or electric shock to persons.
The exclamation point within a triangle is intended to alert the user to the pres­ence of important operating and main­tenance (servicing) instructions in the literature accompanying the product.
See bottom of projector.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
WARNING:
To reduce the risk of fi re or electric shock, do not expose this product to rain or mois ture.
WARNING:
High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.
Page 6
2
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit. Do not touch the glass surface of the lamp unit or the inside of the projector. Do not loosen other screws except for the lamp unit cover and lamp unit. Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.
Carefully change the lamp by following the instructions described on pages
60 to 62.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
Page 7
3
Introduction
How to Read this Operation Manual
The specifi cations are slightly different, depending on the model. However, you can connect and operate all models in the same manner.
In this operation manual, the illustration and the screen display are simplifi ed for explanation, and may differ slightly from the actual display. The examples used throughout this manual are based on the PG-D3550W/PG-D3050W model.
39
Useful
Features
Adjustment buttons (P/R/O/Q)
ENTER button
RETURN button
Press RETURN to return to the previou s screen when the menu is displayed.
MENU button
Adjustment buttons (P/R/O/Q)
MENU button
ENTER button
Menu Selections (Quick Start Menu)
This operation can also be performed by using the buttons on the projector.
1
Press MENU.
The “Quick Start Menu” scre en for the selected Input mode is displayed.
2
Press P or R to selec t the
desired item, then p ress ENTER.
3
Press P/R/O/Q to adjust the
item selected, then press ENTER.
Info
To display the advanced settings and adjustments, select “Go To Complete Menu”. Press ENTER to display the Complete Menu screen. If you do not want to display the Quick Start Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
- “Quick Start Menu” to “Off ”. (See page
52.)
2
Example
SEL./ADJ. ENTER END
Input Search Start Resolution Resize
0 Eco+Quiet Language
Keystone
Information
1024×768 Normal
English
Off
Quick Start Menu
Go To Complete Menu…
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used functions, or the Complete Menu, which enables advanced settings and adjustments.
Buttons used in this operation
On-screen display
Button used in this step
Info
.........Indicates safeguards for using the projector.
Note
.......
Indicates additional information for setting up and operating the projector.
For Future Reference
Maintenance
P. 57
Troubleshooting
PP. 65 and 66
Index
P. 70
Page 8
4
Contents
Preparing
Introduction
How to Read this Operation Manual ......3
Contents .................................................4
IMPORTANT SAFEGUARDS ..................6
How to Access the PDF Operation
Manuals..............................................10
Accessories ..........................................11
Part Names and Functions ...................12
Front View .............................................. 12
Top View ................................................ 12
Rear View (Terminals) .............................. 13
Inserting the Batteries ............................. 15
Usable Range ......................................... 15
Easy Start
Easy Start .............................................16
Setup and Projection .............................. 16
Setup
Setting Up the Projector .......................18
Video Setup............................................ 18
Setting Up the Projector ......................... 18
Standard Setup (Front Projection) ........... 18
Screen Size and Projection Distance ...... 19
Projection (PRJ) Mode ............................ 20
Ceiling-Mount Setup ............................... 20
Connections
Connecting the Projector to
Other Equipment ................................21
Controlling the Projector by
a Computer ........................................24
Connecting the Power Cord .................25
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 30
Resize Mode .......................................... 31
Useful Features
Operating with the Remote Control......33
Displaying and Setting the
Break Timer ......................................... 33
Displaying the Pointer ............................. 33
Using the Spot Function ......................... 33
Switching the Eco+Quiet Mode .............. 33
Auto Sync (Auto Sync Adjustment) ......... 34
Freezing a Moving Image ........................ 34
Selecting the Picture Mode ..................... 34
Displaying an Enlarged Portion of
an Image ............................................. 34
Using the Remote Control as the
Wireless Computer Mouse ................... 35
Menu Items ...........................................36
Using the Menu Screen ........................39
Menu Selections (Quick Start Menu) .........39
Quick Start Menu .....................................40
Menu Selections (Complete Menu) ...........40
Picture Adjustment (“Picture” Menu) ....42
Selecting the Picture Mode ..................... 42
Adjusting the Image ................................ 43
Adjusting the Color Temperature ............. 43
Adjusting the Colors ............................... 43
Selecting the Film Mode ......................... 44
Reducing Image Noise (DNR) ................. 44
Eco+Quiet .............................................. 44
Signal Adjustment (“SIG-ADJ” Menu) ..45
Adjusting the Computer Image ............... 45
Resolution Setting .................................. 45
Signal Type Setting ................................. 45
Selecting the Dynamic Range ................. 45
EDID Selection ....................................... 46
Setting the Video System ....................... 46
Setting the Video Setup .......................... 46
Checking the Input Signal ....................... 46
Adjusting the Projected Image
(“SCR - ADJ” Menu) ...........................47
Setting the Resize Mode ......................... 47
Adjusting the Image Position .................. 47
Keystone Correction ............................... 47
Setting the Overscan .............................. 48
Setting the On-screen Display ................ 48
Closed Caption ...................................... 48
Selecting the Background Image ............ 49
Selecting the Setup Guide ...................... 49
Reversing/Inverting Projected Images ..... 49
Selecting the Wall Color .......................... 49
Selecting the On-screen Display Language
... 49
Using
Basic Operation
Turning the Projector On/Off ................26
Turning the Projector On ......................... 26
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 26
Image Projection ..................................27
About the Setup Guide ........................... 27
Adjusting the Projected Image ................ 27
Correcting Trapezoidal Distortion ............ 29
Switching the Input Mode ....................... 30
Adjusting the Volume .............................. 30
Page 9
5
Introduction
Adjusting the Projector Function
(“PRJ - ADJ1/2” Menu) ......................50
Auto Sync (Auto Sync Adjustment) ......... 50
Auto Power Off Function ........................ 50
Auto Restart Function ............................. 50
Speaker Setting ...................................... 50
Selecting the Transmission Speed
(RS-232C) ........................................... 50
Fan Mode Setting ................................... 51
System Lock Function ............................ 51
Keylock Function .................................... 52
Selecting the Quick Start Menu .............. 52
COMPUTER2 Select .............................. 52
Setting the FUNCTION Button Operation
.. 53
STANDBY Mode ..................................... 53
STANDBY Audio Out .............................. 53
DLP
®
LinkTM ............................................ 53
DLP
®
LinkTM Invert .................................. 53
Returning to the Default Settings ............ 53
Checking the Lamp Life Status ............... 53
Setting Up the Projector Network
Environment (“Network” Menu)..........54
Setting a Password ................................ 54
DHCP Client Setting ............................... 55
TCP/IP Setting ........................................ 55
Returning to Default Settings (Network) .. 55
Restart Network Function ....................... 55
Confi rming the Projector Information ....... 56
Reference
Appendix
Maintenance .........................................57
Maintenance Indicators ........................58
Regarding the Lamp .............................60
Lamp...................................................... 60
Caution Concerning the Lamp ................ 60
Replacing the Lamp ............................... 60
Removing and Installing the
Lamp Unit ............................................ 61
Resetting the Lamp Timer ...................... 62
Storing the Projector ............................63
How to Use the Storage Case ................ 63
Compatibility Chart ..............................64
Troubleshooting ....................................65
For SHARP Assistance .........................67
Specifi cations .......................................68
Dimensions ...........................................69
Index .....................................................70
Page 10
6
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recom mended by the manufacturer.
9. Transportation
A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The open ings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This prod uct should not be placed in a built-in installation such as a book case or rack unless proper ventilation is provided or the manufacturer's instruc tions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following types of plugs. If the plug should fail to fi t into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug. a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug
with a grounding terminal.
This plug will only fi t into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will pre vent damage to the product due to lightning and power-line surges.
Page 11
7
Introduction
15. Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fi re or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fi re or electric shock. Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dan ger ous voltage or other hazards. Refer all servicing to qualifi ed service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualifi ed service personnel under the following conditions: a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions. Adjust only those con trols that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualifi ed technician to restore the product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service technician has used replace ment parts specifi ed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fi re, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to per form safety checks to determine that the product is in proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifi ers) that produce heat.
DLP® and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor
TM
and DLP® LinkTM are trademarks of Texas Instruments.
Microsoft
®
and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other countries. PC/AT is a registered trademark of International Business Machines Corporation in the United States. Adobe
®
Reader® is a trademark of Adobe Systems Incorporated.
Macintosh
®
is a registered trademark of Apple Computer, Inc. in the United States and/or other countries. HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. PJLink is a registered trademark or an application trademark in Japan, the United States, Canada, E.U., China and/or other countries/regions. All other company or product names are trademarks or registered trademarks of their respective companies. Some IC chips in this product include confi dential and/or trade secret property belonging to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse assemble or discompile the contents thereof.
Page 12
8
Observe the following safeguards when setting up your projector.
Caution concerning the lamp unit
Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Regarding the Lamp” on page
60.
Caution concerning the setup of the projector
For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.
Rest your eyes occasionally.
Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.
Do not set up the projector in places exposed to direct sunlight or bright light.
Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing diffi cult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.
Caution regarding placing of the projector
Place the projector on a level site within the adjustment range (9 degrees) of the adjustment foot.
After the projector is purchased, a faint smell from the vent may appear when the power is fi rst turned on. This is normal and is not a malfunction. It will disappear after the projector is used for a while.
When using the projector in high­altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)
When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system. Use the projector at altitudes of 2,300 meters (7,500 feet) or less.
Warning about placing the projector in a high position
When placing the projector in a high position, make certain it is carefully secure to avoid personal injury caused by the projector falling down.
Do not subject the projector to hard impact and/or vibration.
Protect the lens so as not to hit or damage the surface of the lens.
Avoid locations with extremes of temperature.
The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C). The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake vents.
Allow at least 11 13/16 inches (30 cm) of space between the exhaust vent and the nearest wall or obstruction. Ensure that the intake vent and the exhaust vent are not obstructed. If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into Standby mode to prevent overheat damage. This does not indicate a malfunction. (See pages 58 and 59.) Remove the projector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.
Page 13
9
Introduction
Caution regarding usage of the projector
If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it. Do not carry the projector by holding the lens. When storing the projector, ensure that you close the lens shutter. Do not expose the projector to direct sunlight or place next to heat sources. Doing so may affect the cabinet color or cause deformation of the plastic cover.
Other connected equipment
When connecting a computer or other audio-visual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected. Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.
Using the projector in other countries
The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.
Temperature monitor function
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “ ” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. Refer to “Maintenance Indicators” on pages 58 and 59 for details.
Info
The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this license (“Fonts”) and associated documentation fi les (the “Font Software”), to reproduce and distribute the Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one or more of the Font Software typefaces.
The Font Software may be modifi ed, altered, or added to, and in particular the designs of glyphs or characters in the Fonts may be modifi ed and additional glyphs or characters may be added to the Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been modifi ed and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILIT Y, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further information, contact: fonts at gnome dot org.
Page 14
10
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe® Reader® on your computer (Windows
®
or Macintosh®).
Please download Adobe
®
Reader® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals
For Windows®:
Insert the CD-ROM in the CD-ROM drive. Double click the “My Computer” icon. Double click the “CD-ROM” drive.When you want to view the operation
manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the projector manuals.
When you want to view the SETUP MANUAL
1) Double click the “SETUP” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the SETUP MANUAL.
For Macintosh®:
Insert the CD-ROM in the CD-ROM drive. Double click the “CD-ROM” icon.When you want to view the operation
manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the projector manuals.
When you want to view the SETUP MANUAL
1) Double click the “SETUP” folder.
2) Double click the language (name of the folder) that you want to view.
3) Double click the pdf fi le to access the SETUP MANUAL.
If the desired pdf fi le cannot be opened by double clicking the mouse, start Adobe® Reader® fi r s t , then specify the desired fi le using the “File”, “Open” menu.
Note
SETUP MANUAL
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Connecting Pin Assignments ······················································· 2 RS-232C Specifi cations and Commands ····································· 4 Operating the Projector Using the PJLinkTM Protocol ·················· 10 Setting up the Projector Network Environment ·························· 11 Controlling the Projector via LAN ··············································· 17 Resetting the Lamp Timer of the Projector via LAN····················22 Troubleshooting ·········································································· 24
Page 15
11
Introduction
Accessories
Supplied accessories
Power cord*
For U.S. and Canada, etc.
(6' (1.8 m))
<QACCDA007WJPZ>
For Europe, except U.K.
(6' (1.8 m))
<QACCVA011WJPZ>
For U.K. and
Singapore (6' (1.8 m))
<QACCBA036WJPZ>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA018WJPZ>
(1) (2) (3) (4)
* Which power cords are supplied along with your projector depends on the region. Use the power
cord that corresponds to the wall outlet in your country. Operation manuals (this manual <TINS-E588WJZZ>, OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION <TINS-E643WJZZ> and CD-ROM <UDSKAA127WJZZ>)
Remote control
<RRMCGA837WJSA>
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
RGB cable
(10' (3.0 m))
<QCNWGA086WJPZ>
DIN-D -sub RS-232C adapto r
(557/64" (15 cm))
<QCNWGA091WJPZ>
Storage case
<GCASNA024WJSA>
Codes in “< >” are Replacement parts codes.
Note
Optional accessories
Lamp unit
Ceiling-mount adaptor
Ceiling-mount bracket
Ceiling-mount unit
Ceiling-mount extension tube
Remote receiver
3 RCA to mini D-sub 15 pin cable (10n (3.0 m))
AN-D350LP AN-60KT AN-XRCM30 (for U.S.A. only) AN-TK201 <for AN-60KT> AN-TK202 <for AN-60KT> AN-EP101B <for AN-XRCM30> (for U.S.A. only) AN-MR2 AN-C3CP2
Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.
Note
Page 16
12
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the topic is explained.
2
45 6
3
7 8
9
1
11
12
13
15
14
10
16
17
18
19
PG-D2870W
3
2
45 6
3
7 8
9
1
11
12
13
15
14
10
16
17
18
19
PG-D2870W
3
Front View
1 Exhaust vent
57
2 Zoom ring (except PG-D2870W)
28
For enlarging/reducing the picture.
3 Focus ring
27
For adjusting the focus.
4 Lens shutter
26, 30
5 HEIGHT ADJUST lever
28
6 Adjustment foot
28
7 Remote control sensor
15
8 Speaker
50
9 Intake vent
57
Top Vie w
10 Temperature warning indicator
58
11 Lamp indicator
58
12 Power indicator
58
13 STANDBY/ON button
26
For turning the power on and putting the
projector into Standby mode.
14 INPUT buttons (P/R)
30
For switching Input mode.
15 AUTO SYNC button
34
For automatically adjusting images when
connected to a computer.
16 Adjustment buttons (P/R/O/Q)
39
For selecting menu items.
17 ENTER button
39
For setting items selected or adjusted on
the menu.
18 MENU button
39
For displaying adjustment and setting
screens.
19 VOL (Volume) buttons (–O/Q+)
30
For adjusting the speaker sound level.
Page 17
13
Introduction
15
10
141312
123 5
46789
11
15
10
141312
123 5
46789
11
Rear View (Terminals)
1 LAN terminal
25
Terminal for controlling the projector using a
computer via network.
2 RS-232C terminal
24
Terminal for controlling the projector using a
computer.
3 USB terminal
35
Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.
4 HDMI terminal
21, 22, 23
Terminal for HDMI input.
5 AUDIO OUT terminal
23
Audio output terminal of equipment connected to the audio input terminal.
6 MONITOR OUT* terminal
23
(Output terminal for computer RGB and component signals)
Terminal for connecting a monitor.
COMPUTER/COMPONENT 2* input terminal
21, 22
Terminal for computer RGB and component signals.
* You must switch the setting depending on
whether you are using the terminal for MONITOR OUT or COMPUTER/COMPONENT 2 input.
7 AUDIO 1 input terminal
23
8 COMPUTER/COMPONENT 1 input
terminal
21, 22
Terminal for computer RGB and component signals.
9 S-VIDEO input terminal
22
Terminal for connecting video equipment with an S-video terminal.
10 VIDEO input terminal
22
Terminal for connecting video equipment.
11 AUDIO 2 input terminal
23
12 AC socket
25
Connect the supplied power cord.
13 Kensington Security Standard
connector
14 Rear adjustment foot
28
15 Security bar
Using the Kensington Lock
This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.
Page 18
14
2
3
4
7 8
10
6
1
9
11 12
13
14
15
16
18
20 21 22
23
19
17
5
MOUSE/Adjustment buttons (P/R/O/Q)
35, 39
For moving the computer cursor when with the USB connection (using a USB cable or the optional remote receiver). For selecting and adjusting menu items.
8
L-CLICK/EFFECT button
35, 33
For the Left click when with the USB connection (using a USB cable or the optional remote receiver). For changing the pointer or spot area.
9
KEYSTONE button
29
For entering the Keystone Correction mode.
10
AUTO SYNC button
34, 50
For automatically adjusting images when connected to a computer.
11
FUNCTION button
53
For operating and executing a function assigned to “FUNCTION Button”.
12
ECO+QUIET button
33
For lowering the noise of the cooling fan and extending the lamp life.
13
FREEZE button
34
For freezing images.
14
AV MUTE button
30
For temporarily displaying a black screen and turning off the sound.
15
VOL +/– (Volume) buttons
30
For adjusting the speaker sound level.
16
SPOT button
33
For displaying the spotlight.
17
ENTER button
39
For setting items selected or adjusted on the menu.
18
R-CLICK/RETURN button
35, 39
For the Right click when with the USB connection (using a USB cable or the optional remote receiver). For returning to the previous menu screen during menu operations.
19
MENU button
39
For displaying adjustment and setting screens.
20
RESIZE button
31
For switching the picture size (NORMAL, 16:9, etc.).
21
3D MODE button
See the OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION provided separately.
22
PICTURE MODE button
34
For selecting the appropriate picture.
23
ON button
26
For turning the power on.
1
STANDBY button
26
For putting the projector into the Standby mode.
2
BREAK TIMER button
33
For displaying the break time.
4
MAGNIFY buttons
34
For enlarging/reducing part of the image.
5
PAGE UP/PAGE DOWN buttons
35
Same as the [Page Up] and [Page Down] keys on a computer keyboard, when with the USB connection (using a USB cable or the optional remote receiver).
6
POINTER button
33
For displaying the pointer.
7
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic is explained.
INPUT buttons ( /)
30
For switching Input mode.
3
Page 19
15
Introduction
Inserting the Batteries
1
Pull down the tab on the cover and remove the
cover towards the direction of the arrow.
2
Insert the batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment.
3
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below
Caution
Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.
Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. Batteries of different types have different properties, therefore do not mix batteries of different types. Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fl uid from leaked batteries is harmful to skin, therefore ensure you wipe them fi rst and then remove them using a cloth.
The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries. Remove the batteries from the remote control if you will not be using the remote control for a long time. Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
1
Usable Range
The remote control can be used to control the projector within the ranges shown in the illustration.
The signal from the remote control can be refl ected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.
Note
When using the remote control
Ensure that you do not drop it or expose it to moisture or high temperature. The remote control may malfunction under a fl uorescent lamp. In this case, move the projector away from the fl uorescent lamp.
Remote control sensor
Remote control signal transmitters
Remote control
33n (10 m)
30°
30°
Remote control sensor
Remote control signal transmitters
Remote control
33n (10 m)
30°
30°
Page 20
16
Easy Start
This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
STANDBY button
8
KEYSTONE button
5
3
ON button
6
INPUT buttons
5
Adjustment buttons (P/R/O/Q)
6
INPUT buttons
6
STANDBY/ON button
3 8
Focus ring
4
HEIGHT ADJUST lever
4
Zoom ring (except PG-2870W)
4
6
O/Q buttons
1. Place the projector facing a wall or a screen
B
P. 18
When connecting equipment other than a computer, see pages
22 and 23.
2. Connect the projector to the computer and plug the power cord into the AC socket of the projector
BPP. 21, 25
On the projector On the remote control
3. Open the lens shutter fully and then turn the projector on
BP. 2 6
Page 21
17
Easy Start
1 After the projector turns on, the Setup Guide appears.
(When “Setup Guide” is set to “On”. See page
49.)
2
Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size.
3 After adjusting the focus, height (angle) and picture size, press ENTER to fi nish the
Setup Guide.
4. Adjust the projected image with the Setup Guide
BP. 2 7
Correcting trapezoidal distortion using Keystone Correction.
On the remote control
Shrinks
upper side.
Shrinks
lower side.
5. Correct trapezoidal distortion
BP. 2 9
Press INPUT P/R to display the INPUT list. Use INPUT P/R to select the Input mode, and use O/Q to select the audio input terminal.
On the
projector
On the remote
control
INPUT list
1 COMPUTER1
INPUT Audio
2 MONITOR OUT
HDMI
H
On the
projector
On the remote
control
6. Select the Input mode
BP. 3 0
7. Turn the computer on
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press the button again while the confi rmation message is displayed to put the projector into Standby mode.
On-screen display
On the
projector
On the remote
control
8. Turn the power off
BP. 2 6
Page 22
18
Setting Up the Projector
Video Setup
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See page 46.)
Setting Up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's feet fl at and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 29.)
Standard Setup (Front Projection)
Place the projector at the required distance from the screen according to the desired picture size. (See page 19.)
300" (762 cm)
200" (508 cm)
100" (254 cm)
40" (102 cm)
3'10
"–
4'8
"
(1.2 m – 1.4 m)
9'8
"–
11'8
"
(2.9 m – 3.6 m)
19'4
"–
23'5
"
(5.9 m – 7.1 m)
28'11
"–
35'1
"
(8.8 m – 10.7 m)
[PG-D3550W/PG-D3050W]
Picutre Size
Projection Distance
254"
×159"
(646 cm ×
404 cm)
170"
×
106"
(431 cm
×
269 cm)
85"
×
53"
(215 cm
×
135 cm)
34"
×
21"
(86 cm
×
54 cm)
Indication of the Projection Image Size and Projection Distance
Example: 16:10 Signal Input (Normal Mode)
150" (381 cm)
[PG-D2870W]
Picutre Size
100" (254 cm)
60" (152 cm)
3'1
"
(0.9 m)
5'1
"
(1.5 m)
7'7
"
(2.3 m )
Projection Distance
127"
×
79"
(323 cm
×
202 cm)
85"
×
53"
(215 cm
×
135 cm)
51"
×
32"
(129 cm
×
81 cm)
Page 23
19
Setup
Screen Size and Projection Distance
Screen
Lens center
H
L
16:10 Signal Input (Normal Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
PG-D3550W/PG-D3050W
PG-D2870W
PG-D3550W/ PG-D3050W
PG-D2870W
Diagonal [F]
Width Height Minimum [L1] Maximum [L2]
300"(762 cm) 646 cm (254") 404 cm (159") 8.8 m (28' 11") 10.7 m (35' 1") 8 cm
(3")
250"(635 cm) 538 cm (212") 337 cm (132") 7.4 m (24' 2") 8.9 m (29' 3") 6 cm
(21/2")
200"(508 cm) 431 cm (170") 269 cm (106") 5.9 m (19' 4") 7.1 m (23' 5") 5 cm
(2")
150"(381 cm) 323 cm (127") 202 cm (79") 4.4 m (14' 6") 5.4 m (17' 7") 2.3 m (7' 7") 4 cm
(1 1/2")
8 cm
(3 1/32")
120"(305 cm) 258 cm (102") 162 cm (64") 3.5 m (11' 7") 4.3 m (14' 1") 1.9 m (6' 1") 3 cm
(1 13/64")
6 cm
(227/64")
100"(254 cm) 215 cm (85") 135 cm (53") 2.9 m (9' 8") 3.6 m (11' 8") 1.5 m (5' 1") 3 cm
(1")
5 cm
(21/32")
80"(203 cm) 172 cm (68") 108 cm (42") 2.4 m (7' 9") 2.9 m (9' 4") 1.2 m (4' 1") 2 cm
(51/64")
4 cm
(1 5/8")
60"(152 cm) 129 cm (51") 81 cm (32") 1.8 m (5' 9") 2.1 m (7' 0") 0.9 m (3' 1") 2 cm
(19/32")
3 cm
(1 7/32")
40"(102 cm) 86 cm (34") 54 cm (21") 1.2 m (3' 10") 1.4 m (4' 8") 1 cm
(13/32")
4:3 Signal Input (Normal Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens center
to the bottom of the image [H]
PG-D3550W/PG-D3050W
PG-D2870W
PG-D3550W/ PG-D3050W
PG-D2870W
Diagonal [F]
Width Height Minimum [L1] Maximum [L2]
300"(762 cm) 610 cm (240") 457 cm (180")
10.0 m
(32' 9") 12.1 m (39' 9") 9 cm
(3 13/32")
250"(635 cm) 508 cm (200") 381 cm (150") 8.3 m (27' 4") 10.1 m (33' 2") 7 cm
(253/64")
200"(508 cm) 406 cm (160") 305 cm (120") 6.7 m (21' 10") 8.1 m (26' 6") 6 cm
(217/64")
150"(381 cm) 305 cm (120") 229 cm (90") 5.0 m (16' 5") 6.1 m (19' 11") 4 cm
(1 45/64")
120"(305 cm) 244 cm (96") 183 cm (72") 4.0 m (13' 1") 4.8 m (15' 11") 2.1 m (6' 11") 3 cm
(1 23/64")
7 cm
(23/4")
100"(254 cm) 203 cm (80") 152 cm (60") 3.3 m (10' 11") 4.0 m (13' 3") 1.8 m (5' 9") 3 cm
(1 9/64")
6 cm
(219/64")
80"(203 cm) 163 cm (64") 122 cm (48") 2.7 m (8' 9") 3.2 m (10' 7") 1.4 m (4' 7") 2 cm
(29/32")
5 cm
(1 53/64")
70"(178 cm) 142 cm (56") 107 cm (42") 2.3 m (7' 8") 2.8 m (9' 3") 1.2 m (4' 0") 2 cm
(51/64")
4 cm
(1 39/64")
60"(152 cm) 122 cm (48") 91 cm (36") 2.0 m (6' 7") 2.4 m (7' 11") 1.1 m (3' 5") 2 cm
(11/16")
3 cm
(1 3/8")
40"(102 cm) 81 cm (32") 61 cm (24") 1.3 m (4' 4") 1.6 m (5' 4") 1 cm
(29/64")
When using the projector with screen sizes not listed in the above charts, calculate the values according to the formulas.
16:10 Signal 4:3 Signal
[m/cm] [Feet/inches] [m/cm] [Feet/inches]
PG-D3550W/ PG-D3050W
L1: Minimum projection distance (m/ft) 0.02942F0.02942F / 0.3048 0.03331F0.03331F / 0.3048 L2: Maximum projection distance (m/ft) 0.03568
F
0.03568F / 0.3048 0.04039F0.04039F / 0.3048
H: Distance from the lens center to the bottom of the
image (cm/in)
0.02545
F
0.02545F / 2.54 0.02881F0.02881F / 2.54
PG-D2870W
L: Projection distance (m/ft) 0.01549F0.01549F / 0.3048 0.01754F0.01754F / 0.3048 H: Distance from the lens center to the bottom of the
image (cm/in)
0.05142F0.05142F / 2.54 0.05821F0.05821F / 2.54
F
: Picture diagonal size : 40
''
-300'' (PG-D3550W/PG-D3050W)
60
''
-150'' (16:10)/60''-120'' (4:3) (PG-D2870W)
Allow a margin of error in the values in the diagrams below.
Note
Page 24
20
Setting Up the Projector (Continued)
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR­ADJ” menu. See page 49.)
Table mounted, front projection
[Menu item ➞ “Front”]
Table mounted, rear projection (with a translucent screen)
[Menu item “Rear”]
Ceiling mounted, front projection
[Menu item “Ceiling + Front”]
Ceiling mounted, rear projection (with a translucent screen)
[Menu item “Ceiling + Rear”]
a
Ceiling-Mount Setup
It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold separately).
Page 25
21
Connections
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the equipment to be connected. After making all connections, turn on the projector and then the other pieces of equipment. When connecting a computer, ensure that it is the last equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.
For more details of connection and cables, refer to the operation manual of the connecting equipment. You may need other cables or connectors not listed below.
Terminals on the Projector
Equipment
Terminal on
connected equipment
Cable
Terminal on the
projector
Computer
RGB
output
terminal
RGB cable (supplied) COMPUTER/
COMPONENT 1, 2
HDMI output
terminal
HDMI cable (commercially available) HDMI
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission may not work property. (The HDMI specifi cation does not support all connections to equipment that has digital output terminal using a DVIÙHDMI digital cable.) You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external equipment. (See page
52.)
See page
64 “Compatibility Chart” for a list of computer signals compatible with the projector. Use
with computer signals other than those listed may cause some of the functions to not work. A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.
Depending on the computer you are using, an image may not be projected unless the computer's external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specifi c instructions in
your computer's operation manual to enable your computer's external output port.
Note
Page 26
22
Connecting the Projector to Other Equipment (Continued)
Equipment
Terminal on
connected equipment
Cable
Terminal on the
projector
Video equipment
HDMI output
terminal
HDMI cable (commercially available) HDMI
Component
video output
terminal
3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)
COMPUTER/ COMPONENT 1, 2
S-video
output
terminal
S-video cable (commercially available) S-VIDEO
Video output
terminal
Video cable (commercially available) VIDEO
Camera/Video game
Component
video
output
terminal
Cables for a camera or a video game/3 RCA to mini D-sub 15 pin cable (optional, AN-C3CP2)
RCA adaptor plug (commercially available)
COMPUTER/ COMPONENT 1, 2
S-video
output
terminal
Cables for a camera or a video game
S-VIDEO
Video
output
terminal
Cables for a camera or a video game
VIDEO
Depending on specifi cations of equipment or the DVIÙHDMI digital cable, the signal transmission may not work property. (The HDMI specifi cation does not support all connections to equipment that has digital output terminal using a DVIÙHDMI digital cable.) HDMI (High-Defi nition Multimedia Interface) is a digital AV interface that can deliver a high-defi nition video signal, multi-channel audio signal, and bi-directional control signal all in just one cable. Because it is compatible with the HDCP (High-bandwidth Digital Content Protection) system, the digital video signal does not degrade when transmitted, and a high-quality image with a simple connection can be enjoyed. The HDMI terminal does not support the CEC signal. You can also use the COMPUTER/COMPONENT 2 terminal as the MONITOR OUT terminal. To use this terminal as an input terminal, set “COMPUTER2 Select” to “Input” before connecting the external equipment. (See page
52.)
When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a commercially available cable that fi ts in the projector terminal you want to connect. The projector does not support RGBC signals via the Euro-scart.
Note
Page 27
23
Connections
Equipment
Terminal on
connected equipment
Cable
Terminal on the
projector
Audio equipment
ø3.5 mm
audio output
terminal
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp ser vice part QCNWGA038WJPZ)
AUDIO 1
RCA audio
output
terminal
RCA audio cable (commercially available)
AUDIO 2
Audio
output
terminal
Cables for a camera or a video game
HDMI output
terminal
HDMI cable (commercially available) HDMI
Monitor RGB
input
terminal
RGB cable (supplied or commercially available)
MONITOR OUT
Amplifi er
ø3.5 mm
audio input
terminal
ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp ser vice part QCNWGA038WJPZ)
AUDIO OUT
RCA audio
input
terminal
ø3.5 mm stereo minijack to RCA audio cable (commercially available)
You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. To use this terminal as an output terminal, set “COMPUTER2 Select” to “Monitor Output” before connecting the external equipment. (See page
52.)
When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable. You can select AUDIO 1, AUDIO 2 or HDMI in the INPUT list. (See page
30.)
RGB signals and Component signals can be output to the monitor. HDMI input video signal would not be output.
Note
This projector is able to process the following signals when connected to HDMI equipment:
Video signal: For details, see “Digital Support” in the list of “Compatibility Chart” on page 64. Audio signal: Linear PCM audio Sampling frequency: 48kHz/44.1kHz/32kHz
Page 28
24
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS­232C adaptor (supplied) and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifi cations and Commands”.
When connecting to a computer using a DIN-D-sub RS-232C adaptor (supplied) and an RS-232C serial control cable
RS-232C serial control cable (cross type, commercially available)
Computer
DIN-D-sub RS-232C adaptor (supplied)
To RS-232C terminal
To RS-232C terminal
The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details. Refer to pages 2 to 9 of the “SETUP MANUAL” contained on the supplied CD-ROM for “Connecting Pin Assignments” and “RS-232C Specifi cations and Commands”.
Note
Info
Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector. Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.
Page 29
25
Connections
When connecting to the LAN terminal using a LAN cable
LINK LED (green) Illuminates when linked.
TX/RX LED (yellow) Illuminates when transmitting/receiving data.
* To ensure safety, do not connect the LAN terminal
with any cables that may cause excessive voltage such as a telephone line.
Hub
or
Computer
LAN cable (Category 5 type, commercially available)
To LAN terminal
When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially available). When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially available).
Note
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.
AC socket
To AC outlet Power cord (supplied)
AC socket
To AC outlet Power cord (supplied)
Page 30
26
Turning the Projector On/Off
Turning the Projector On
Note that the connections to external equipment and power outlet should be done before performing the operations written below. (See pages
21 to 25.)
Open the lens shutter fully and press STANDBY/ON on the projector or ON on the remote control.
The power indicator illuminates green. After the lamp indicator illuminates, the projector is ready to start operation.
About the Lamp Indicator
The lamp indicator illuminates to indicate the status of the lamp.
Green: The lamp is on. Blinking in green: The lamp is warming up. Red: The lamp is shut down
abnormally or the lamp should be replaced.
When switching on the projector, a slight fl ickering of the image may be experienced within the fi rst minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation. If the projector is put into Standby mode and immediately turned on again, the lamp may take some time to start projection. When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page
51 for details.
Note
Turning the Power Off (Putting the Projector into Standby Mode)
Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confi rmation message is displayed, to put the projector into Standby mode.
The projector cannot be turned on while cooling.
Info
When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page
50.)
English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page
49.
STANDBY/ON button
Lamp indicator
Power indicator
STANDBY button
ON button
On-screen display (confi rmation message)
Info
Direct Power Off function:
You can unplug the power cord from the AC outlet even if the cooling fan is still running.
Page 31
27
Basic
Operation
Image Projection
About the Setup Guide
After turning on the projector, the Setup Guide screen appears to assist you with projector setup.
Guidance items
1 FOCUS 2 HEIGHT ADJUST 3 ZOOM*
Press ENTER to exit the Setup Guide screen.
The Setup Guide screen automatically highlights the items in the following order:
1 FOCUS
3 ZOOM*4 ENTER
2 HEIGHT ADJUST
However, you can adjust the focus, height (angle) or zoom* regardless of the highlighted item. If you do not want to display the Setup Guide for the next time, set “Menu” - “SCR - ADJ” ­“Setup Guide” to “Off”. (See page
49.)
Note
* The PG-D2870W model is not equipped with
the ZOOM function.
Adjusting the Projected Image
1 Adjusting the Focus
You can adjust the focus with the focus ring on the projector.
Rotate the focus ring to adjust the focus while watching the projected image.
Using the knob on the focus ring will make the adjustments easier.
Setup Guide screen (e.g. PG-D3550W/PG-D3050W)
PG-D2870W
ENTER button
Focus ring
Page 32
28
Image Projection (Continued)
2 Adjusting the Height
The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector.
When the screen is above the projector, the projection image can be made higher by adjusting the projector.
1
Lift the projector to adjust its
height while lifting the HEIGHT ADJUST lever.
2
Remove your hands from the
HEIGHT ADJUST lever of the projector after its height has been fi nely adjusted.
The angle of projection is adjustable up to 9 degrees from the surface on which the projector is placed.
3
Use the rear adjustment foot to
make the projector level.
The projector is adjustable ±2 degrees from the standard position.
When adjusting the height of the projector, trapezoidal distortion occurs. Follow the procedures in Keystone Correction to correct the distortion. (See pages
29 and 47.)
Note
3 Adjusting the Picture Size (except PG-D2870W)
You can adjust the picture size using the zoom ring on the projector.
Rotate the zoom ring to enlarge or shrink the picture size.
Using the knob on the zoom ring will make the adjustments easier.
Zoom ringZoom ring
Rear adjustment footRear adjustment foot
HEIGHT ADJUST lever
Make small adjustments.
Info
Do not apply too much pressure on the projector when the front adjustment foot comes out. When lowering the projector, be careful not to get your fi ngers caught in the area between the adjustment foot and the projector. Hold the projector fi rmly while lifting or carrying. Do not hold by the lens area.
Page 33
29
Basic
Operation
Correcting Trapezoidal Distortion
When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
The Keystone Correction can be adjusted up to an angle of approximately ±40 (PG-D3550W/ D3050W)/±XX (PG-D2870W) degrees and the screen can also be set up to an angle of approximately ±40 (PG-D3550W/D3050W)/ ±XX (PG-D2870W) degrees (When the Resize mode is set to “NORMAL” (see page
31))
.
Note
1
Press KEYSTONE to enter the
Keystone Correction mode.
2
Press P/Q or O/R to adjust the
Keystone Correction.
To return to the default setting, press RETURN while the on-screen display of the Keystone Correction mode is on the screen.
Note
3
Press KEYSTONE.
The on-screen display of the Keystone Correction mode will disappear.
KEYSTONE button
Adjustment buttons (P/R/O/Q)
RETURN button
On-screen display (Keystone Correction mode)
0KEYSTONE
ADJUST END
Shrinks upper side. (Move the slide bar in the + direction.)
Shrinks lower side. (Move the slide bar in the - direction.)
Info
While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged.
Page 34
30
Switching the Input Mode
Select the appropriate Input mode for the connected equipment.
Press INPUT
/ to display the INPUT list. Use INPUT
/ to select the Input
mode, and use O/Q to select the audio input terminal.
Adjusting the Volume
Press VOL +/– on the remote control or –O/Q+ on the projector to adjust the volume.
Pressing VOL–/–O will lower the volume. Pressing VOL+/Q+ will raise the volume. When the projector is connected to external equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector's volume to the lowest level when turning the projector on/off or when changing the input signal. When you do not want to output the sound from the projector's speaker while the projector is connected to external equipment, set “Speaker” in the “PRJ-ADJ1” menu to “Off”. (See page
50.)
Note
Displaying the Black Screen and Turning Off the Sound
Temporarily
Press AV MUTE on the remote control or close the lens shutter to temporarily display a black screen and turn off the sound.
Pressing AV MUTE again will turn the projected image back on. When you close the lens shutter, the projector will be set to AV Mute mode and then the projector will be turned off automatically after about 30 minutes.
Note
VOL +/– (Volume) buttons
INPUT buttons
AV MUTE button
O/Q buttons
VOL +/– (Volume) buttons
INPUT buttons
AV MUTE button
O/Q buttons
On-screen displayOn-screen display
On-screen displayOn-screen display
Image Projection (Continued)
Page 35
31
Basic
Operation
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
See page 47 for setting on menu screen.
COMPUTER
NORMAL FULL NATIVE 16:9
4:3 aspect ratio
SVGA (800 × 600)
1068 × 800
1280u 800
800 × 600
1280 × 720
XGA (1024 × 768) 1024 × 768
SXGA (1152 × 864) 1152 × 864
SXGA+ (1400 × 1050) 1400 × 1050
Other aspect ratios
SXGA (1280 × 1024) 1000 × 800 1280 × 1024
1280 × 720 1280 × 720
1360 × 768 1280 × 722 1360 × 768 1366 × 768 1280 × 720 1366 × 768 1280 × 768 1280 × 768
1280 × 720
1280 × 800 1280 × 800
Input signal Output screen image
Computer Image type NORMAL FULL NATIVE 16:9
Resolution
XGA and below
4:3 aspect ratio
*1
Resolution
higher than
XGA
*3
SXGA
(1280 × 10 24)
5:4 aspect ratio
*1
1280 × 720
16:9 aspect ratio
*1
*2
*2
1360 × 768 1366 × 768
16:9 aspect ratio
1280 × 768
15:9 aspect ratio
*1
*2
*1
1280 × 800
16:10 aspect ratio
*2
*1
: Cutout area on which images cannot be projected
: Area where the signals are off screen *1 The Image Shift function can be used for these images. *2 Same as NORMAL mode. *3 In case SXGA+ input.
RESIZE button
RESIZE button
Page 36
32
VIDEO/DTV
Input signal Output screen image
Video/DTV Image type NORMAL AREA ZOOM V-STRETCH 16:9
480I, 480P, 576I, 576P,
NTSC, PAL,
SECAM
4:3 aspect ratio
*1
Squeeze
*1
Letter box
*1
720P, 1035I,
1080I, 1080P
16:9 aspect ratio
*1
*2
16:9 aspect ratio
*1
540P
16:9 aspect ratio
*1
16:9 aspect ratio
(4:3 aspect ratio in 16:9)
*1
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals *1 The Image Shift function can be used for these images. *2 Same as NORMAL mode.
About Copyrights
When using the Resize function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size. The use of the Resize or Keystone Correction function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.
Image Projection (Continued)
Page 37
33
Useful
Operating with the Remote Control
POINTER button
ECO+QUIET button
Adjustment buttons (P/R/O/Q)
BREAK TIMER button
SPOT button
AUTO SYNC button
FREEZE button
PICTURE MODE button
MAGNIFY buttons
EFFECT button
Displaying and Setting the Break Timer
1
Press BREAK TIMER.
The timer starts to count down from 5 minutes.
On-screen display
2
Press P/R/O/Q to adjust the
length of the break time.
Increases with P or Q
5 minutes 6 minutes 60 minutes
Shortens with O or R
4 minutes 3 minutes ➞1 minute The break time can be set in units of one minute (up to 60 minutes).
Canceling the break timer display function
Press BREAK TIMER.
The Break Timer is not available while the projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute
- Input Search
Note
1
Displaying the Pointer
1
Press POINTER and press P/R/
O/Q on the remote control to move the pointer.
Press EFFECT to change the pointer icon (5 types).
Star
Finger1 Finger2 Heart Underline
2
Press POINTER again.
The pointer will disappear.
Using the Spot Function
1
Press SPOT and press P/R/O/Q
on the remote control to move the spot area.
Press EFFECT to change the spot area size (3 types).
1/9 1/25 1/8
2
Press SPOT again.
The spot area will disappear.
Switching the Eco+Quiet Mode
Press ECO+QUIET to switch the Eco+Quiet mode between on and off.
When the Eco+Quiet Mode is set to “ON”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.
Refer to “Eco+Quiet” on page 44 for details.
Note
1
Page 38
34
Operating with the Remote Control (Continued)
Auto Sync (Auto Sync Adjustment)
Auto Sync function works when detecting input signal after the projector turns on.
Press AUTO SYNC to manually adjust with Auto Sync function.
When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page
45.)
Note
Freezing a Moving Image
1
Press FREEZE.
The projected image is frozen.
2
Press FREEZE again to return to
the moving image from the currently connected device.
Selecting the Picture Mode
You can select the appropriate Picture mode for the projected image, such as movie or video game.
Press PICTURE MODE.
When pressing PICTURE MODE, the Picture mode changes in the following order:
STANDARD PRESENTATION MOVIE GAME sRGB
*
See page 42 for details on the Picture mode.
Note
* “sRGB” is displayed only when RGB signal is input.
Displaying an Enlarged Portion of an Image
Graphs, tables and other portions of projected images can be enlarged. This is helpful when providing more detailed explanations.
1
Press MAGNIFY on the
remote control.
Enlarges the image. Pressing
or MAGNIFY enlarges
or reduces the projected image.
×1 ×2 ×3 ×4
Press
.
Press
.
You can change the location of the enlarged image using P, R, O and Q.
Note
2
Press RETURN on the remote
control to cancel the operation.
The magnifi cation then returns to u1.
The selectable magnifi cations differ depending on the input signal. In the following cases, the image will return to the normal size (u1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and refresh rate (vertical frequency) change.
- When the Resize mode is changed.
Note
Page 39
35
Useful
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the USB cable, the remote receiver (optional, AN-MR2) makes it possible to operate the projector with the remote control. For details, see the operation manual of the receiver.
Connecting with a USB cable
or
R
emote receiver
(optional, AN-MR2)
To USB terminal
USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)
To USB terminal
Computer
The mouse pointer can be operated in the following way after it is connected.
When moving the cursor
Press MOUSE/Adjustment buttons (P/R/O/Q).
When left-clicking
Press L-CLICK.
When right-clicking
Press R-CLICK.
When your computer supports only a one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK. L-CLICK and R-CLICK have common function.
When using [Page Up] or [Page Down]
MOUSE/Adjustment buttons (//?/_)
R-CLICK button
L-CLICK button
PAGE UP/ PAGE DOWN button
s
MOUSE/Adjustment buttons (//?/_)
R-CLICK button
L-CLICK button
PAGE UP/ PAGE DOWN button
s
Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE DOWN.
This function only works with the Microsoft® Windows® OS and Mac OS® that support USB. You cannot use this function when displaying the menu screen. Confi rm that the computer recognizes the USB connection.
Note
Page 40
36
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
Main menu Sub menu
Picture
Page 42 Page 42
Page 43
Page 43
Page 43
Page 43
Page 43
Page 44
Page 44
+30-30
Contrast
+30-30
+30-30
+30-30
1-1
20
+30-30
+30-30
+30-30
Tint
Color
Sharp
Bright
Film Mode
Eco+Quiet
[On/Off]
Reset
Auto Off
CLR Temp
BrilliantColor™
C.M.S. Setting [On/Off]
C.M.S.
Standard Presentation Movie Game sRGB *3
Picture Mode
*4
*4
*4
Red
Blue
*4
Page 44
DNR Level 1
Level 2 Level 3
C.M.S.-Hue
C.M.S.-Saturation
C.M.S.-Value
Page 43
Page 43
Page 43
Reset
Return
+30-30
R
+30-30
+30-30
+30-30
+30-30
+30-30
C
G
B
Y
M
Reset
*3 Item when inputting RGB signal through
COMPUTER 1/2 or HDMI.
*4 Items when inputting component signal through
COMPUTER 1/2 or HDMI, or when selecting S-VIDEO or VIDEO.
“Quick Start Menu”
Main menu
Normal Full Native Area Zoom V-Stretch 16:9
Quick Start Menu
Input Search Start
Resolution
Eco + Quiet
[On/Off]
Resize
Information
Go To Complete Menu
Keystone
-80 +80 *1
-XX +XX *2
Language
Sub menu
Page 40
Page 40
Page 40
Page 40
Page 40
Page 40
Page 40
Page 40
English Deutsch Español Nederlands Français Italiano Svenska Português
polski Magyar Türkçe
*1 Adjustment range for PG-D3550W/D3050W. *2 Adjustment range for PG-D2870W.
Page 41
37
Useful
“Screen adjustment (SCR-ADJ)” menu
Main menu Sub menu
SCR - ADJ
Page 47
Language
Image Shift
Resize
Page 47
Page 47
Page 47
Page 48
Page 49
Page 49
Page 49
OSD Display [On/Off]
Page 48
Closed Caption
Page 48
Overscan [On/Off]
Background
PRJ Mode
Logo Blue None
Page 49
Wall Color Off
Blackboard Whiteboard
Page 49
Setup Guide [On/Off]
Off CC1 CC2
Front Ceiling + Front Rear Ceiling + Rear
+96-96
Normal Full Native Area Zoom V-Stretch 16:9
Keystone
-80 +80 *1
-XX +XX *2
English Deutsch Español Nederlands Français Italiano Svenska Português
polski Magyar Türkçe
“Signal adjustment (SIG-ADJ)” menu
Main menu Sub menu
SIG-ADJ
Page 45
Page 45
Page 45
Page 45
Page 45
Page 46
Signal Type
Video Setup
Signal Info
Auto RGB YPbPr
Resolution
0 IRE
7.5 IRE
EDID Selection
Standard Enhanced
Page 46
Page 46
Video System Auto
PAL SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60
+30-30
+60-60
+150-150
+150-150
Clock
Phase
H-Pos
V-Pos
Reset
*5
*5
*6
*6
*6
*7
Dynamic Range Auto
Standard Enhanced
*8
*10
*9
*5 Items when inputting RGB signal through
COMPUTER/COMPONENT 1 or 2.
*6
Items when inputting COMPUTER/COMPONENT 1, 2 or HDMI.
*7
Item when selecting COMPUTER/COMPONENT 1, 2 or HDMI
. *8 Item when selecting HDMI. *9 Item when selecting COMPUTER/COMPONENT 1
or 2.
*10 Item when selecting S-VIDEO or VIDEO.
Page 42
38
“Projector adjustment (PRJ-ADJ1/2)” menu
Main menu Sub menu
PRJ-ADJ1
Page 50
Speaker [On/Off]
System Lock [Enable/Disable]
Keylock [On/Off]
Auto Restart [On/Off]
Page 50
Auto Power Off [On/Off]
Page 50
Page 50
Page 51
Page 52
Fan Mode
Page 51
Normal High
RS-232C
Page 50
9600bps 38400bps 115200bps
Auto Sync [On/Off]
Page 50
Main menu Sub menu
Page 53
Page 52
Page 53
Page 53
Page 53
Page 53
Page 53
Page 52
PRJ-ADJ2
COMPUTER2 Select
Input Monitor Output
FUNCTION Button
Input Search Audio Mute Image Shift Signal Info
STANDBY Mode
Quick Start Eco
All Reset
Lamp Timer (Life)
Page 53
DLP® LinkTM [On/Off]
STANDBY Audio Out [On/Off]
DLP® LinkTM Invert
Quick Start Menu [On/Off]
Page 50
“Network” menu
Main menu
Network
Page 54
Password [Enable/Disable]
DHCP Client
[On/Off]
TCP/IP
Projector
Link
Page 54
Page 55
Page 55
Reset Network Setting
Restart Network
IP Address
Page 55
Page 55
Page 56
Page 56
MAC Address
Page 56
Page 56
Main menu
Menu Items
(Continued)
Page 43
39
Useful
Adjustment buttons (P/R/O/Q)
ENTER button
RETURN button
Press RETURN to return to the previous screen when the menu is displayed.
MENU button
Adjustment buttons (P/R/O/Q)
MENU button
ENTER button
Menu Selections (Quick Start Menu)
This operation can also be performed by using the buttons on the projector.
1
Press MENU.
The “Quick Start Menu” screen for the selected Input mode is displayed.
2
Press P or R to select the
desired item, then press ENTER.
3
Press P/R/O/Q to adjust the
item selected, then press ENTER.
Info
To display the advanced settings and adjustments, select “Go To Complete Menu”. Press ENTER to display the Complete Menu screen. If you do not want to display the Quick Start Menu, set “Go To Complete Menu” - “PRJ-ADJ2”
- “Quick Start Menu” to “Off”. (See page
52.)
2
Example
SEL./ADJ. ENTER END
Input Search Start Resolution Resize
0 Eco+Quiet Language
Keystone
Information
1024×768 Normal
English
Off
Quick Start Menu
Go To Complete Menu…
Using the Menu Screen
Select from the Quick Start Menu, which is a collection of the most frequently used functions, or the Complete Menu, which enables advanced settings and adjustments.
Page 44
40
Using the Menu Screen
(Continued)
Quick Start Menu
The following items can be confi gured on the Quick Start Menu.
Selectable items Description
Input Search Start Automatically searches for and switches to the appropriate Input mode.
Pressing an operation button during input searching cancels the search.
Resolution Manually change the resolution.
Use this function when the image and screen size do not match with the resolution selected automatically. (See page
45.)
Resize Changes the Resize mode.
Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen. (See page
47.)
Keystone Corrects the keystone distortion of projected images.
Use this function to correct the trapezoidal distortion of images caused when projecting images at an angle to the screen. (See page
47.)
Eco+Quiet When set to “On”, this function reduces the cooling fan noise and power
consumption, thereby prolonging the operating life of the lamp. (See page
44.)
Language Selects the language displayed on the screen. (See page 49.) Information Displays the input signal, lamp use time, remaining lamp life, etc. Go To Complete Menu Displays the Complete Menu for advanced settings and adjustments.
The setting of Resize mode will be made independently for each Input mode. The setting of Eco+Quiet mode will be made independently for each Input mode and each Picture mode.
Note
Menu Selections (Complete Menu)
Example: Adjusting “Bright”.
This operation can also be performed by using the buttons on the projector.
1
Press MENU.
The “Quick Start Menu” screen is displayed.
2
Press P or R to select “Go To
Complete Menu”.
3
Press Q or O and select
“Picture” to adjust.
Info
When “PRJ-ADJ2” - “Quick Start Menu” is set to “On”, pressing MENU displays the Quick Start Menu screen.
Example: “Picture” screen menu for COMPUTER (RGB) input
Menu item
Picture Mode
Contrast 0
0 0
Bright
Standard
SEL./ADJ. ENTER END
0 0
Red Blue CLR Temp BrilliantColor
TM
C.M.S. Setting C.M.S.
Eco+Quiet
0 1
On
Off
DNR
Level 2
Reset
SIG SCR PRJ1 PRJ2 Net.Picture
Page 45
41
Useful
4
Press P or R and select “Bright”
to adjust.
The selected item is highlighted.
To adjust the projected image while watching it
Press ENTER.
The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen. When pressing P or R, the following item (“Red” after “Bright”) will be displayed.
Press ENTER again to return to the previous screen.
Note
5
Press O or Q to adjust the item
selected.
The adjustment is stored.
6
Press MENU.
The menu screen will disappear.
0Bright
Picture
SEL./ADJ. Rtn. Menu END
Picture Mode
Standard
SEL./ADJ. Single ADJ END
Resize Image Shift 0
0
Keystone
Normal
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. END
0 0
Red Blue CLR Temp BrilliantColor
TM
C.M.S. Setting C.M.S.
Eco+Quiet
0 1
On
Off
Reset
Bright 0
DNR
Level 2
Picture Net.
Pict. SCR-ADJ Net.
SIG
PRJ1 PRJ2
SIG SCR PRJ1 PRJ2Picture
Items to be adjusted
The item displayed by itself
Press ENTER.
0Bright
Picture
SEL./ADJ. Rtn. Menu END
Picture Mode
Standard
SEL./ADJ. Single ADJ END
Resize Image Shift 0
0
Keystone
Normal
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. END
0 0
Red Blue CLR Temp BrilliantColor
TM
C.M.S. Setting C.M.S.
Eco+Quiet
0 1
On
Off
Reset
Bright 0
DNR
Level 2
Picture Net.
Pict. SCR-ADJ Net.
SIG
PRJ1 PRJ2
SIG SCR PRJ1 PRJ2Picture
Items to be adjusted
The item displayed by itself
Press ENTER.
5
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. Single ADJ END
0 0
Red Blue
CLR Temp BrilliantColor
TM
C.M.S. Setting C.M.S.
Eco+Quiet
0 1
On
Off
Reset
15Bright
DNR
Level 2
Picture SIG SCR PRJ1 PRJ2 Net.
Picture Mode
Contrast 0
0
Standard
SEL./ADJ. Single ADJ END
0 0
Red Blue
CLR Temp BrilliantColor
TM
C.M.S. Setting C.M.S.
Eco+Quiet
0 1
On
Off
Reset
15Bright
DNR
Level 2
Picture SIG SCR PRJ1 PRJ2 Net.
The MENU button is not available while the projector is operating:
- Auto Sync/Break Timer/Freeze/AV Mute/Input Search
Note
Page 46
42
Picture Adjustment (“Picture” Menu)
Menu operation n Page 40
Q PAGE1 Q PAGE2
Picture Mode
Contrast 0
0 0 0
Bright Color Tint
0Sharp
Standard
SEL./ADJ. ENTER END
0 0
Red Blue
Picture SIG SCR PRJ1 PRJ2 Net.
1
2
Picture Mode
CLR Temp BrilliantColor
TM
C.M.S. Setting C.M.S.
Standard
SEL./ADJ. ENTER END
Film Mode
Eco+Quiet
0 1
On
Auto
Off
DNR
Level 2
Reset
7
6
5
4
2
3
Picture SIG SCR PRJ1 PRJ2 Net.
1
Selecting the Picture Mode
Selectable
items
Description
The default settings of each item when selecting Picture Mode
CLR Temp BrilliantColor
TM
Eco+Quiet Standard For standard image 0 1 Off Presentation Brightens portions of image for
more enhanced presentations.
02Off
Movie Gives natural tint to the
projected image.
–1 0 On
Game Gives sharpness to the
projected image.
01Off
*sRGB For high fi delity reproduction of
images from a computer.
––Off
“sRGB” is displayed only when RGB signal is input. You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are retained in memory.
You can also press PICTURE MODE on the remote control to select the Picture mode. (See page 34.) *sRGB is an international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fi xed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when “sRGB” is selected. You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColor
TM
”, when “sRGB” is selected.
Note
Info
When “sRGB” is selected, the projected image may become dark, but this does not indicate a malfunction.
Page 47
43
Useful
Menu operation n Page 40
2
Adjusting the Image
Adjustment
items
O button Q button
Contrast For less
contrast.
For more contrast.
Bright For less
brightness.
For more brightness.
Color*
1
For less color intensity.
For more color intensity.
Tint*
1
For making skin tones purplish.
For making skin tones greenish.
Sharp*
1
For less sharpness.
For more sharpness.
Red*
2
For weaker red. For stronger
red.
Blue*
2
For weaker blue.
For stronger blue.
BrilliantColor™*2*3For making the
effect weaker.
For making the effect stronger.
*1 Not displayed in the RGB input mode. *2 Not adjustable/selectable when selecting “sRGB”. *3 BrilliantColor™ uses Texas Instruments'
BrilliantColor™ technology. As the BrilliantColor™ level is increased, the image becomes brighter while the color reproduction is kept at a high level.
“Red”, “Blue”, “BrilliantColorTM” and “CLR Temp” cannot be set when “sRGB” is selected. To reset all adjustment items, select “Reset” and press ENTER.
Note

Adjusting the Color
Temperature
Selectable
items
Description
–1
0
1
For lower color temperature for warmer, reddish incandescent-like images.
For higher color temperature for cooler, bluish, fl uorescent-like images.
Values on “CLR Temp” are only for general standard purposes.
Note
4
Adjusting the Colors
This function adjusts each of the six main colors that comprise the color wheel, altering their “Hue”, “Saturation”, or “Value”.
Selectable items Description
C.M.S.-Hue Sets the hue of the main colors. C.M.S.-Saturation Sets the saturation of the main
colors
C.M.S.-Value Sets the brightness of the main
colors.
Reset The adjustments of “Hue”,
“Saturation” and “Value” of all colors are reset to the default setting.
Return Returns to the “Picture” menu
screen.
Adjusting “Hue”, “Saturation”, or “Value”.
1 Select “On” for “C.M.S. Setting” in the “Picture”
menu and then press ENTER.
2 Select “C.M.S.” in the “Picture” menu and then
press ENTER.
3 Press P or R to select either “Hue”, “Saturation”, or
“Value” and then press ENTER.
4 Select the color to be adjusted with P or R and
adjust it with O or Q.
Example of adjusting the “Hue”
Main colors O button Q button
R (Red)
Closer to magenta
Closer to yellow Y (Yellow) Closer to red Closer to green G (Green) Closer to yellow Closer to cyan C (Cyan) Closer to green Closer to blue B (Blue) Closer to cyan
Closer to magenta M (Magenta) Closer to blue Closer to red
When “Saturation” is selected, the selected color becomes O: lighter. Q: thicker. When “Value” is selected, the selected color becomes O: darker. Q: brighter. To reset the adjustment values of each color to the default settings, select “Reset” and press ENTER.
Page 48
44
5
Selecting the Film Mode
This function provides high-quality playback of images originally projected at 24 fps, such as movies on DVDs.
Selectable
items
Description
Auto Films are detected automatically. Off Films are not detected.
This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:
- 480I
- 576I
- 1035I
- 1080I With S-VIDEO or VIDEO input:
- All signals
Note
6
Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.
Selectable
items
Description
Level 1
Sets the DNR level for viewing a clearer picture.
Level 2 Level 3
This function is not available for some signals.
Note
Picture Adjustment (“Picture” Menu) (Continued)
Menu operation n Page 40
7
Eco+Quiet
Selectable
items
Brightness and Power consumption
On Approx. 65% Off 100%
When “Eco+Quiet” is set to “On”, the fan sound and power consumption are lower than they are when “Off” is selected. (Projection brightness decreases as shown in the chart.)
Note
Page 49
45
Useful
Signal Adjustment (“SIG-ADJ” Menu)
Menu operation n Page 40
0 0 0 0
Phase
Clock
H-Pos V-Pos
Reset
Auto
1024 x 768
0 IRE
Resolution Signal Type
Video Setup
Standard
EDID Selection
Standard
Dynamic Range
Signal Info 1024 x 768
H 48.3 kHz / V 60.0 Hz
Auto
Video System
SEL./ADJ. ENTER END
Pict. SIG-ADJ SCR PRJ1 PRJ2 Net.
 
-2
-1
1
Adjusting the Computer Image
If the optimum image cannot be obtained with Auto Sync adjustment, use the SIG-ADJ function.
Selectable
items
Description
Clock Adjusts vertical noise. Phase Adjusts horizontal noise (similar to
tracking on your VCR).
H-Pos Centers the on-screen image by
moving it to the left or right.
V-Pos Centers the on-screen image by
moving it up or down.
To reset all adjustment items, select “Reset” and press ENTER. The adjustable range of “H-Pos” (H-Position) and “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.
Note
2
Resolution Setting
Ordinarily, the type of input signal is detected and the correct Resolution mode is automatically selected. However, for some signals, the optimal Resolution mode in “Resolution” may need to be selected to match the computer display mode.
See “Checking the Input Signal” on page 46 for information on the currently selected input signal.
Note
3
Signal Type Setting
This function allows you to select the input signal type RGB or Component for COMPUTER/ COMPONENT 1 or 2.
Selectable
items
Description
Auto Input signals are automatically
recognized as RGB or component. RGB Set when RGB signals are received. YPbPr Set when Component signals are
received.
4
Selecting the Dynamic Range
An optimum picture may not be displayed if an HDMI-capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch “Dynamic Range”.
Selectable
items
Description
Auto In most circumstances, “Auto” should
be selected. Standard When the black levels of the image
show banding or appear faded, select
the item that results in the best picture
quality.
Enhanced
The Dynamic Range can be selected only when “HDMI” input mode is selected.
Note
Page 50
46
5
-1 EDID Selection
EDID (Extended Display Identifi cation Data) is data that enables a computer to make proper display settings. When you cannot fi nd the desired resolution on your computer, switch EDID selection. If still unsuccessful, reboot the computer.
Selectable
items
Description
Standard Standard setting. Enhanced When the desired resolution cannot
be found in standard setting.
5
-2
Setting the Video System
The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the Video signal difference. In that case, switch the Video signal.
Selectable items
Auto PAL SECAM *NTSC4.43 NTSC3.58 PAL-M PAL-N PAL -60
* When reproducing NTSC signals in PAL
video equipment.
The Video signal can only be set in S-VIDEO or VIDEO mode. When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.
Note
Signal Adjustment (“SIG-ADJ” Menu) (Continued)
Menu operation n Page 40
6
Setting the Video Setup
Selectable
items
Description
0 IRE Sets the black level to 0 IRE.
7.5 IRE Sets the black level to 7.5 IRE.
This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:
- 480I With S-VIDEO or VIDEO input:
- NTSC3.58
Note
7
Checking the Input Signal
This function allows you to check the current input signal information.
Page 51
47
Useful
Adjusting the Projected Image (“SCR-ADJ” Menu)
Menu operation n Page 40
SEL./ADJ. ENTER END
Resize Image Shift 0
0
Keystone
OSD Display Closed Caption
Overscan
Background Setup Guide PRJ Mode
On
Front Wall Color Language
Off
English
On
Off
Logo
On
Normal
Pict. PRJ1 PRJ2 Net.SIG
SCR-ADJ
9
8
0
5 6
4
3
2
1
7
1
Setting the Resize Mode
Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen.
For details of the Resize mode, see pages
31 and 32.
You can also press RESIZE on the remote control to set the Resize mode. (See page
31.)
Note
2
Adjusting the Image
Position
You can move the projected image vertically.
Q buttonO button
This function only works in some Resize modes. (See pages
31 and 32.)
Note
3
Keystone Correction
When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.
Select “Keystone” on the “SCR-ADJ” menu and adjust with the slide bar.
See page 29 for details of Keystone Correction.
O buttonQ button
The Keystone Correction can be adjusted up to an angle of approximately ±40 (PG-D3550W/ D3050W)/±XX (PG-D2870W) degrees (When the Resize mode is set to “NORMAL”). You can also press KEYSTONE on the remote control to adjust Keystone Correction.
Note
Page 52
48
4
Setting the Overscan
This function allows you to set the overscan area (display area).
Selectable
items
Description
On The input area is displayed without the
screen edges.
Off The whole input area is displayed.
This function is available for the following signals. With COMPUTER/COMPONENT 1 or 2 input:
- 480P
- 540P
- 576P
- 720P
- 1035I
- 1080I/1080P If noise appears at the screen edges when “Off” is selected, set the function to “On”. Also see “About Copyrights” on page
32.
Note
5
Setting the On-screen
Display
Selectable
items
Description
On All on-screen displays are displayed. Off VOLUME/AV MUTE/FREEZE/AUTO
SYNC/RESIZE/PICTURE MODE/ ECO+QUIET/MAGNIFY/Input Search/ Audio Mute/“An invalid button has been pressed.” are not displayed.
6
Closed Caption
<For Americas only>
Info
This function is available for NTSC3.58 signal. This function is available in the following cases only:
Resize
mode
Keystone Correction
PG-D3550W/
D3050W
PG-D2870W
Normal Area Zoom V-Stretch
-40 − +40 -XX − +XX
16:9 -12 − +12 -XX − +XX
“Closed Caption” is a system which allows conversations, narration, and sound effects in TV programs (Limited regions) and home videos to be viewed as captions on the screen. Not all programs and videos will offer closed captioning. Please look for the symbol to ensure that captions will be shown. Two channels are available: CC1 and CC2.
Selectable
items
Description
Off — CC1 Closed Caption mode for CH1 data CC2 Closed Caption mode for CH2 data
Closed Caption may malfunction (white blocks, strange characters, etc.) if signal conditions are poor or if there are problems at the broadcast source. This does not necessarily indicate a problem with the projector. If any button is pressed to call up the on­screen display while viewing a Closed Caption broadcast, the closed captions will disappear.
Note
Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued)
Menu operation n Page 40
Page 53
49
Useful
7
Selecting the Background
Image
Selectable items Description
Logo Sharp logo screen Blue Blue screen None
8
Selecting the Setup Guide
Selectable items Description
On Displaying the Setup Guide
when turning the projector on.
Off Not displaying the Setup Guide.
9
Reversing/Inverting
Projected Images
Selectable items Description
Front Normal image (Projected from
the front of the screen)
Ceiling + Front Inverted image (Projected from
the front of the screen with an inverted projector)
Rear Reversed image (Projected from
the rear of the screen or with a mirror)
Ceiling + Rear Reversed and inverted image
(Projected with a mirror)
See page
20 for details of Projection (PRJ) Mode.
Menu operation n Page 40
0
Selecting the Wall Color
This function allows you to project the image to a colored (white or dark green) surface or wall without using a screen.
Selectable items Description
Off The Wall Color function is not
activated.
Blackboard Projects images onto a
blackboard (dark green).
Whiteboard Projects images onto a
whiteboard.
Selecting the On-screen
Display Language
The projector can switch the on-screen display language among 17 languages.
English Deutsch Español Nederlands Français Italiano Svenska Português
Türkçe
polski Magyar
Page 54
50
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu)
Menu operation n Page 40
Q PRJ-ADJ1
SEL./ADJ. ENTER END
Auto Power Off On Auto Restart On Speaker On
OffKeylock
9600bps
System Lock
RS-232C Fan Mode Normal
Disable
Auto Sync On
Pict. SCR PRJ-ADJ1SIG PRJ2 Net.
1 2 3 4 5
7
6
8
1
Auto Sync (Auto Sync
Adjustment)
Selectable
items
Description
On Auto Sync adjustment will occur when
the projector is turned on or when the input signals are switched, when connected to a computer.
Off Auto Sync adjustment is not
automatically performed.
Auto Sync adjustment is also performed by pressing AUTO SYNC. The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector. When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page
45.)
Note
2
Auto Power Off Function
Selectable
items
Description
On When no input signal is detected for
more than 15 minutes, the projector will automatically enter Standby mode.
Off The Auto Power Off function will be
disabled.
When the Auto Power Off function is set to “On”, 5 minutes before the projector enters Standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.
Note
Q PRJ-ADJ2
Pict. SCR PRJ-ADJ2SIG Net.
SEL./ADJ. ENTER END
COMPUTER2 Select
DLP
®
Link
TM
h
Off
Monitor Output FUNCTION Button Input Search STANDBY Mode Quick Start
STANDBY Audio Out On
0 min0Lamp Timer(Life) 100%
DLP
®
Link TM Invert
Quick Start Menu On
PRJ1
All Reset
 
3
Auto Restart Function
Selectable
items
Description
On
If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on.
Off The projector does not turn on
automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.
4
Speaker Setting
Selectable
items
Description
On The audio signal is output from the
internal speaker.
Off The audio signal is not output from the
internal speaker.
5
Selecting the Transmission
Speed (RS-
232C)
Make sure that both the projector and computer are set for the same baud rate.
Selectable
items
Description
9600bps
38400bps
115 20 0bps
Transmission speed is slow.
Transmission speed is rapid.
Page 55
51
Useful
6
Fan Mode Setting
This function changes the fan rotation speed.
Selectable
items
Description
Normal Suitable for normal environments. High Set when using the projector at
altitudes of approximately 1,500 meters (4,900 feet) or more.
When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.
7
System Lock Function
This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest
you record the keycode in a safe place where only authorized users have access.
Info
If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page
67). Even
if the product warranty is valid, the keycode reset will incur a charge.
a
Setting/Changing the Keycode
1
Select “System Lock”, then press
ENTER or Q.
2
Select “Next”, then press ENTER.
The screen for entering the keycode appears.
3
Press the 4 buttons on the remote control or on the projector to enter the preset keycode in “Old Code”.
When setting the keycode for the fi rst time, press R on the projector for four times.
Setting the System Lock
PRJ - ADJ1
Old Code
New Code Reconfirm
––––
–––– ––––
Menu operation n Page 40
If you input a wrong keycode, the cursor returns to the fi rst point of the “Old Code”. The preset keycode is 4 R buttons on the projector. When you press the R button four times, the keycord input screen disappears.
Note
4
Press the 4 buttons on the remote
control or on the projector to enter the new keycode in “New Code”.
You cannot use the following buttons for keycode: STANDBY/ON, ON,
STANDBY, ENTER, L-CLICK, R­CLICK/RETURN and MENU System Lock function recognizes each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.
Note
Setting the System Lock
Old Code
New Code
Reconfirm
****
––– ––––
PRJ - ADJ1
5
Enter the same keycode in “Re­confi rm”.
To cancel the keycode that you have already set
Press R on the projector for four times in steps 4 and 5 above.
When the System Lock is set
When System Lock is set, the keycode input screen appears after the power is turned on. When it appears, enter the right keycode to start projection.
Input screen for keycode
System Lock
––––
Note
Page 56
52
8
Keylock Function
Use this function to lock the operation buttons on the projector. This function can be set using either the menu screen or ENTER on the projector.
a
Setting with the menu screen
Selectable
items
Description
On All buttons on the projector, except
STANDBY/ON, are locked.
Off Turns off the Keylock function.
a
Setting with the projector buttons
Locking the Operation Buttons
1
Hold down ENTER on the
projector for about 5 seconds while the projector is being turned on.
The Keylock function screen is displayed.
Use this function to lock the operation buttons on the projector. (Except STANDBY/ON button)
Note: You can release the keylock by holding down ENTER on the projector for about 5 seconds.
PRJ - ADJ1
Return
On
SEL. ENTER END
2
Select “On”, then press
ENTER
.
On-screen display
The Keylock function does not affect the operation with the remote control buttons. You cannot use the Keylock function while the projector is warming up.
Taking the Keylock Off
Hold down ENTER on the projector for about 5 seconds.
On-screen display
Info
Even when Keylock function is set to “On”, STANDBY/ON on the projector can be used to turn on and off the power. Keylock cannot be set while the projector is: displaying the “Setup Guide” or “Menu” screens, in Standby mode, warming up, changing input signals, operating the Auto Sync or Input Search function, in Freeze mode or on the “System Lock” screen during warming up.
9
Selecting the Quick
Start Menu
Selectable items Description
On Pressing MENU displays the
Quick Start Menu screen.
Off Pressing MENU displays the
Complete Menu screen.
0
COMPUTER2 Select
You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. Select whether to use the terminal as an input terminal or output terminal.
Selectable items Description
Input The terminal can be used as an
input terminal (COMPUTER/ COMPONENT 2).
Monitor Output
The terminal can be used as an output terminal (MONITOR OUT).
Set this before connecting the external equipment. The setting cannot be changed when Input mode is “COMPUTER 2”.
Note
Adjusting the Projector Function (“PRJ-ADJ1/2” Menu) (Continued)
Menu operation n Page 40
Page 57
53
Useful
Setting the FUNCTION
Button Operation
You can assign one of the following functions to the FUNCTION button on the remote con­trol. The assigned function can be performed by just pressing FUNCTION.
Selectable items Description
Input Search Automatically searches for and
switches to the appropriate Input mode.
Audio Mute For temporarily turning off the
sound. Press FUNCTION again to turn on the sound
Image Shift For moving the projected image
vertically. (See page
47.)
Signal Info
Input signal information is displayed.
STANDBY Mode
When set to “Eco”, power consumption is reduced in Standby mode.
Selectable
items
Description
Eco The monitor output, RS-232C and
Network functions are switched off in Standby mode.
Quick Start The monitor output, RS-232C and
Network functions are activated even if the projector is in Standby mode.
STANDBY Audio Out
You can set audio output from the AUDIO OUTPUT terminal of the projector that is in Standby mode.
Selectable
items
Description
On The audio signal is output from the
AUDIO OUTPUT terminal in Standby mode.
Off The audio signal is not output from the
AUDIO OUTPUT terminal in Standby mode.
When “Eco” is selected for “STANDBY Mode”, “STANDBY Audio Out” is set to “Off” automatically and you cannot change the setting. The HDMI audio will not output from the AUDIO OUTPUT terminal when the projector is in Standby mode.
Note
Menu operation n Page 40
DLP® Link
TM
See the OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION provided separately.
DLP® LinkTM Invert
See the OPERATION MANUAL FOR STEREOSCOPIC 3D PROJECTION provided separately.
Returning to the Default
Settings
This function allows you to initialize the settings you have made in the projector.
The following items or menu cannot be initialized.
- Resolution
- Language
- Lamp Timer (Life)
- System Lock
- COMPUTER2 Select
Note
Checking the Lamp
Life Status
You can confi rm the cumulative lamp usage time and the remaining lamp life (percentage).
Lamp usage condition Remaining lamp life
“Life” 100% 5%
Operated exclusively with “Eco+Quiet” set to “On”
Approx. 4,000 hours
Approx. 200 hours
Operated exclusively with “Eco+Quiet” set to “Off”
Approx. 2,000 hours
Approx. 100 hours
It is recommended that the lamp be changed when the remaining lamp life becomes 5%. The lamp life may vary depending on the usage condition.
Note
Page 58
54
Setting Up the Projector Network Environment (“Network” Menu)
Menu operation n Page 40
SCRSIG PRJ1 PRJ2
SEL./ADJ. ENTER END
Pict. Network
Password Disable
DHCP Client Off
Restart Network
Reset Network Setting
TCP/IP
IP Address
XXX.XXX.XXX.XXX
MAC Address
XX : XX : XX : XX : XX : XX
Projector
XX-XXXX
Link
Disconnected
6
4
2 3
1
5
1
Setting a Password
If you do not want others to change the setting for the “Network” menu, set a password.
a
Setting a Password
1
Select “Password”, then press
ENTER or Q.
The screen for entering the password appears.
Setting the Password
Old Password
New Password
Reconfirm
–––
–––
––––
Network
2
Press P or R to set the fi rst digit in “New Password”, then press Q.
3
Enter the remaining 3 digits, then
press ENTER.
To return to the previous digit, press O.
4
Enter the same password in
“Reconfi rm”, then press ENTER.
The status for “Password” changes to “Enable”.
Once the password is set, you must enter the password to change the “Network” menu settings.
Note
a
Changing the Password
1
Select “Password”, then press
ENTER or Q.
The screen for entering the password appears.
2
Enter the password in “Old
Password” using P, R, Q and O , then press ENTER.
3
Enter the password in “New
Password” using P, R, Q and O, then press ENTER.
4
Enter the same password again
in “Reconfi rm” using P, R, Q and O, then press ENTER.
If you do not need the password protection for the “Network” menu settings anymore, press ENTER without entering the new password in steps 3 and 4. To cancel the password settings, press RETURN.
Note
If you forget the password
If you forget the password, perform the following procedure to delete it, then set a new password.
On the projector, press
.
If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page
52.)
You cannot use the buttons on the remote control to delete the password.
Note
3
Page 59
55
Useful
2
DHCP Client Setting
Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work.
Selectable items Description
On Obtains confi guration
parameters for TCP/IP network automatically.
Off Sets the TCP/IP manually.
Select “On” for “DHCP Client”. “Obtaining IP Address...” appears, then the menu screen appears. Confi rm the parameters of IP Address, Subnet Mask and Gateway on the TCP/IP screen.
If the DHCP server is not available, “Could not obtain IP Address.” appears.
In this case, set the TCP/IP manually. (See the item 3.)
3
TCP/IP Setting
Set the TCP/IP manually.
1
Select “Off” for “DHCP Client”,
then press ENTER.
2
Select “TCP/IP”, then press
ENTER.
3
Enter “IP Address” using P, R, Q
and O, then press ENTER.
Network
Setting the TCP/IP
Subnet Mask
IP Address
Gateway
1
55 .2
92 .
000 .
1
55 .2
68 .
000 .
1
55 .2
50 .
000 .
0
000
02
000
4
Enter “Subnet Mask” using P, R,
Q and O, then press ENTER.
5
Enter “Gateway” using P, R, Q
and O, then press ENTER.
1
4
Selectable items Description
IP Address Factory default setting:
192.168.150.002 Enter an IP address appropriate for the network.
Subnet Mask Factory default setting:
255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network.
Gateway Factory default setting:
000. 000. 000. 000 * When not in use, set to “000.
000. 000. 000”.
Confi rm the existing network's segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If “192.168.150.002” is not used in a network with an IP address of “192.168.150.XXX”, you don't have to change the projector IP address. For details about each setting, consult your network administrator.
Note
4
Returning to Default
Settings (Network)
This function allows you to initialize the Network settings you have made in the projector.
If the values for IP Address, Subnet Mask or Gateway of the projector have been returned to the default settings, the computer cannot be connected to the projector depending on the computer’s network settings.
Note
5
Restart Network Function
Restarts the network function. Perform this function when the projector cannot be controlled via the network.
Menu operation n Page 40
Page 60
56
6
Confi rming the
Projector Information
You can confi rm the following items.
Selectable
items
Description
IP Address The IP address of the projector is
displayed.
MAC Address The MAC address of the projector is
displayed. Projector The projector name is displayed. Link Displays the network connection
status.
Connected Connected to the
network.
Disconnected Disconnected from
the network.
For information on how to change the projector name, see “SETUP MANUAL” contained in the supplied CD-ROM.
Note
Setting Up the Projector Network Environment (“Network” Menu) (Continued)
Menu operation n Page 40
Page 61
57
Appendix
Maintenance
Cleaning the projector
Ensure that you have unplugged the power cord before cleaning the projector. The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the fi nish on the cabinet. Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or fi nish of the projector. Wipe off dirt gently with a soft fl annel cloth. Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the cabinet or cause cracking. Wiping with a hard cloth or using strong force may scratch the cabinet surface. When the dirt is hard to remove, soak a cloth in a mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.
Mild deterge
nt
Mild detergent diluted
with water
Thinner
Wax
Cleaning the lens
Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating fi lm on the surface of the lens. As the surface of the lens can easily get damaged, be careful not to scrape or hit the lens.
[PG-D2870W Only]
Use a commercially available blower to remove dust. If necessary, gently wipe the lens surface with lens cleaning paper (for plastic lens only). Do not use any liquid type cleaning agents, as they may wear off the coating fi lm on the surface of the lens.
Caution
Do not use any glass cleaner to clean the lens. Avoid touching the lens with your hands to prevent fi ngerprints on or damage to the lens surface.
Cleaning the exhaust and intake vents
Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.
Info
If you want to clean the air vents during projector operation, ensure you press
STANDBY/ON on the projector or STANDBY on the remote control and put the
projector into Standby mode. After the cooling fan has stopped, clean the vents.
Page 62
58
Maintenance Indicators
The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector. If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.
Top View
Lamp indicator
Temperature warning indicator
Power indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location, the temperature warning indicator will blink. And if the temperature keeps on rising, “ ” will illuminate in the lower left corner of the picture with the temperature warning indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then the projector will enter Standby mode. When you fi nd the temperature warning indicator blinking, be sure to perform the measures described on page 59.
About the lamp indicator
When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will automatically turn off and then the projector will automatically enter Standby mode. At this time, the lamp indicator will illuminate in red.
If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.
Indicators on the Projector
Power indicator Red on Normal (Standby)
Green on Normal (Power on) Red blinks Abnormal (See page
59.)
Green blinks Normal (Cooling) Green and orange
blink alternately
The lens shutter is closed. (See page
30.)
Lamp indicator Green on Normal
Green blinks The lamp is warming up. Red on The lamp is shut down abnormally or requires to be
changed. (See page
59.)
Tempe rature warning indicator
Off Normal Red on/Red blinks The internal temperature is abnormally high. (See page
59.)
Page 63
59
Appendix
Maintenance indicator
Problem Cause Possible Solution
Normal Abnormal
Temperature
warning
indicator
Off Red blinks
(On)/
Red on
(Standby)
The internal temperature is abnormally high.
Temperatures around the projector are high. Blocked air intake
Use the projector in an area with a temperature of lower than 95°F (+35ºC). Relocate the projector to an area with proper ventilation. (See page
8.)
Cooling fan breakdown Internal circuit failure Clogged air intake
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page
67) for
repair.
Lamp
indicator
Green on
(Green
blinks
when the
lamp is
warming
up.)
Red on The lamp does
not illuminate.
The lamp is shut down abnormally.
Disconnect the power cord from the AC outlet, and then connect it again.
Time to change the lamp.
Remaining lamp life becomes 5% or less.
Carefully replace the lamp. (See page
60.)
Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page
67) for
repair. Please exercise care when replacing the lamp. Securely install the cover.
Red on
(Standby)
The lamp does not illuminate.
Burnt-out lamp Lamp circuit failure
Power
indicator
Green on/
Red on
Green blinks
(Cooling)
Red blinks The power
indicator blinks in red when the projector is on.
The lamp unit cover is open.
If the power indicator blinks in red even when the lamp unit cover are securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page
67) for
advice.
Info
If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.) If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.
Page 64
60
Regarding the Lamp
Lamp
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. (See page
53.)
Purchase a replacement lamp of type AN-D350LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP
U.S.A ONLY
Caution Concerning the Lamp
This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking. When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally. Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation. Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burns or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.
Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
Page 65
61
Appendix
Removing and Installing the Lamp Unit
Warning!
Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.
Info
Do not touch the glass surface of the lamp unit or the inside of the projector. To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. Do not loosen other screws except for the lamp unit cover and lamp unit.
1
Press STANDBY/ON on the
projector or STANDBY on the remote control to put the projector into Standby mode.
2
Disconnect the power cord.
Unplug the power cord from the AC socket. Leave the lamp until it has fully cooled down (about 1 hour).
3
Remove the lamp unit cover.
Close the lens shutter and turn the projector over. Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover (2).
Lamp unit AN-D350LP
Optional
accessory
Lamp unit AN-D350LP
Optional
accessory
1
STANDBY/ON button
AC socket
STANDBY/ON button
AC socket
User service screw (for lamp unit cover)
User service screw (for lamp unit cover)
Page 66
62
4
Remove the lamp unit.
Loosen the securing screw from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.
5
Insert the new lamp unit.
Press the lamp unit fi rmly into the lamp unit compartment. Fasten the securing screw.
6
Replace the lamp unit cover.
Align the tab on the lamp unit cover (1) and close it (2). Then tighten the user service screw (3) to secure the lamp unit cover.
Info
If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.
1
Connect the power cord and
open the lens shutter fully.
Plug the power cord into the AC socket of the projector.
2
Reset the lamp timer.
While simultaneously holding down MENU, ENTER and
R on the projector,
press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green. “LAMP 0000H” is displayed, indicating that the lamp timer is reset.
4
Securing screw
Securing screw
AC socketAC socket
ENTER button
MENU button
R button
STANDBY/ON button
ENTER button
MENU button
R button
STANDBY/ON button
Regarding the Lamp (Continued)
Page 67
63
Appendix
Storing the Projector
How to Use the Storage Case
When storing the projector, close the lens shutter, and place it in the supplied storage case.
1
Open the cover of the storage
case.
Fold out the inner padding.
2
Place the projector into the
storage case.
Info
Ensure the projector has cooled down suffi ciently before placing it in the case. Ensure the lens shutter is closed for protection.
Place the projector into the storage case with the lens facing the direction indicated in the illustration.
Ensure the projector is held in place by using the fi xing band. Do not expose the storage case to direct sunlight or near heat sources. The storage case may change color or become deformed.
3
Close the cover of the storage
case.
4
Place the accessories in the front
pocket of the storage case.
1
Lens shutter
Fixing band
Supplied accessories (Remote control, etc.)
Page 68
64
Compatibility Chart
Computer
• Multiple signal support Horizontal Frequency: 15-110 kHz, Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-165 MHz Sync signal: Compatible with TTL level
• Compatible with sync on green signal
PC/MAC Mode Resolution
Horizontal frequency
[kHz]
Vertical
frequency[Hz]
Analog
Support
Digital
Support
Display
PC
VGA 6 40 × 480
26.2 50
Upscale
31.5 60
✔✔
34.7 70
37.9 72
✔✔
37.5 75
✔✔
43.3 85
SVGA 800 × 600
31.3 50
35.2 56
✔✔
37.9 60
✔✔
46.6 70
48.1 72
✔✔
46.9 75
✔✔
53.7 85
XGA 1024 × 768
40.3 50
48.4 60
✔✔
56.5 70
✔✔
60.0 75
✔✔
68.7 85
WXGA
1280 × 720 45.0 60
✔✔
TRUE
1280 × 768 47.8 60
✔✔
1280 × 800
49.7 60
✔✔
62.8 75
1360 × 768 47.7 60
✔✔
Intelligent
Compression
1366 × 768 47.8 60
✔✔
WXGA+ 1440 × 900 55.9 60
SXGA
1152 × 864
55.0 60
66.2 70
67.5 75
1280 × 960
60.0 60
✔✔
75.0 75
1280 × 1024
64.0 60
✔✔
80.0 75
✔✔
SXGA+ 1400 × 1050
64.0 60
✔✔
65.3 60
✔✔
WSXGA+ 1680 × 1050 6 5.3 60
UXGA 1600 × 1200 75.0 6 0
MAC 13” VGA 640 × 48 0 3 4.9 67
UpscaleMAC 16” SVG A 832 × 624 49.7 75
MAC 19” XGA 1024 × 768 60.2 75
MAC 21” SXGA 1152 × 870 6 8.7 75
Intelligent
Compression
Optimum image quality will be achieved by matching your computer's output resolution to the resolution that corresponds to “TRUE” in the “Display” column shown above. When “Screen resolution” of the computer is different from the resolution displayed on the projected image, follow the procedures shown below. – Refer to “Resolution” on the “SIG-ADJ” menu and select the same resolution as the resolution in
“Screen resolution” of the computer.
Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution” adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.
Note
DTV
Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
Signal
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Analog
Support
Digital
Support
480
I
15.7 60
1080I
28.1 50
✔✔
480P 31.5 60
✔✔
1080
I
33.8 60
✔✔
540P 33.8 60
1080P 27.0 24
576
I
15.6 50
1080P 28.1 25
576P 31.3 50
✔✔
1080P 33.8 30
720P 37.5 50
✔✔
1080P 56.3 50
✔✔
720P 45.0 60
✔✔
1080P 67.5 60
✔✔
1035
I
33.8 60
Page 69
65
Appendix
Troubleshooting
Problem Check Page
No picture and no sound
or projector does not
start.
Projector power cord is not plugged into the wall outlet.
25
Power to the external connected devices is off. – The lens shutter is closed.
26, 30
The selected Input mode is wrong. 30 The AV Mute function is working. 30 Cables are incorrectly connected to the projector. 21–25 Remote control battery has run out. 15 External output has not been set when connecting a notebook computer.
21 The lamp unit cover is not installed correctly. 61, 62
Sound is heard but no
picture appears
(or picture is dark).
Cables are incorrectly connected to the projector.
21–25
“Bright” is set to minimum position. 43 Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is switched to the external output. Refer to the computer's operation manual for how to switch its signal output settings. Is “On” selected in “DLP
®
LinkTM”?
53
Dark or bluish image
Check that “Wall Color” is confi gured correctly.
49
Color is faded or poor.
Image adjustments are incorrectly set. Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the “BrilliantColor
TM
” value.
43
(S-Video, Video Input only)
Video input system is incorrectly set.
(COMPUTER/COMPONENT 1, 2 Input only)
Input signal type (RGB/Component) is incorrectly set.
46
45
Picture is blurred;
noise appears.
Adjust the focus.
27
The projection distance exceeds the focus range. 19 There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.
(Computer Input only)
Perform “SIG-ADJ” Adjustments (“Clock” and “Phase” Adjustment) Noise may appear depending on the computer.
45
Picture appears but no
sound is heard.
Cables are incorrectly connected to the projector.
21–25
Volume is set to minimum. When the projector is connected to an external device and the volume is set to minimum, the sound is not output even if you turn up the volume of the external device.
30
“Speaker” is set to “Off”. The Audio Mute function is working.
50 53
Data image is not
centered.
Make the necessary adjustments of each item in the “SIG-ADJ” menu.
45
Depending on the computer you are using, the output resolution signal may be different from the one you have set. For details, refer to the operation manual of the computer.
An unusual sound is
occasionally heard from
the cabinet.
If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.
Page 70
66
Problem Check Page
Maintenance indicator on
the projector illuminates
or blinks in red.
See “Maintenance Indicators”.
58
Picture is green on
COMPUTER (YPbPr)/
HDMI (YPbPr)
Change the input signal type setting.
45
Picture is pink
(no green) on
COMPUTER (RGB)/
HDMI (RGB)
Picture is too bright and
whitish.
Image adjustments are incorrectly set.
43
The cooling fan becomes
noisy.
When temperature inside the projector increases, the cooling fan runs faster.
8, 9 57, 58, 5
9
The lamp does not light
up even after the
projector turns on.
The lamp indicator is illuminating in red. Replace the lamp. The lens shutter is closed.
58, 61, 62
26, 30
The lamp suddenly turns
off during projection.
The image sometimes
fl i c k e r s .
Cables are incorrectly connected to the projector or the connected equipment works improperly. If this happens frequently, replace the lamp.
21–25
61
The lamp needs much
time to turn on.
The lamp will eventually need to be changed. While the remaining lamp life draws to a close, replace the lamp.
61
Picture is dark.
The remote control
cannot be used.
Operate the remote control while pointing it at the projector's remote control sensor. The remote control may be too far away from the projector. If direct sunlight or a strong fl uorescent lamp is shining on the projector's remote control sensor, place the projector where it will not be affected by strong light.
15
The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.
15
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
Troubleshooting (Continued)
Page 71
67
Appendix
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
lcdsupport@sharpsec.com
http://www.sharpusa.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico Sharp Electronics Corporation
Mexico Branch
(525) 716-9000 http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin
American Group
(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com
Germany Sharp Electronics (Europe) GMBH
01805-234675 http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
08705 274277
http://www.sharp.co.uk/customersupport
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1 http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr
Spain Sharp Electronica Espana, S.A.
93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se
Austria Sharp Electronics (Europe) GMBH
Branch Offi ce Austria
0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at
Benelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland 9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu
Australia Sharp Corporation of Australia Pty.
Ltd.
1300-135-022 http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
Phone: (09) 573-0111 Fax: (09) 573-0112 http://www.sharp.net.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk
Taiwan Sharp Corporation (Taiwan)
0800-025111 http://www.sharp-scot.com.tw
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E. Sharp Middle East Fze
971-4-81-5311 helpdesk@smef.global.sharp.co.jp
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002 lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr
India Sharp Business Systems (India)
Limited
(91) 11- 6431313 service@sharp-oa.com
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, fi rst refer to the “Troubleshooting” section on pages
65 and 66. If this operation
manual does not answer your question, please contact the SHARP Service departments listed below.
Page 72
68
Specifi cations
Model PG-D3550W/PG-D3050W PG-D2870W Display devices 0.65" DLP
®
Chip ×1 Resolution WXGA (1280 × 800) Lens F number F 2.4 – 2.6 F 2.8
Zoom Manual, ×1.20 — Focus Manual
f = 19.0 – 22.7 mm f = 10.2 mm
Input terminals HDMI ×1
Computer/Component (mini D-sub 15 pin)
×2
S-Video (mini DIN 4 pin) ×1 Video (RCA) ×1 Audio (ø3.5 mm stereo minijack) ×1 Audio (RCA) ×1 (L/R)
Output terminals
Computer/Component (mini D-sub 15 pin)
×1 (Shared with COMPUTER/COMPONENT 2; switchable)
Audio (ø3.5 mm stereo minijack) ×1 (variable audio output)
Control and communication terminals
LAN (RJ-45) ×1 USB (Type B) ×1
RS-232C (mini DIN 9 pin) ×1 Speaker 7W (Mono) Projection lamp 250 W Rated voltage AC 100 – 240 V Rated frequency 50/60 Hz Input current 3.2 A Power consumption Eco+Quiet
Off
AC 100 V 322 W AC 240 V 309 W
Eco+Quiet OnAC 100 V 215 W
AC 240 V 210 W
Power consumption (STANDBY Mode)
Quick Start AC 100 V 4.4 W
AC 240 V 5.2 W
Eco AC 100 V 0.32 W
AC 240 V 0.77 W Operation temperature 41ºF to 95ºF (+5ºC to +35ºC) Cabinet Plastic Dimensions (main body only) [W × H × D] 11
52
/64" × 3 1/8" × 9 19/64"
(300 × 79 × 236 mm)
Weight (approx.) 6.2 lbs. (2.8 kg) 6.4 lbs. (2.9 kg)
As a part of policy of continuous improvement, SHARP reserves the right to make design and specifi cation changes for product improvement without prior notice. The performance specifi cation fi gures indicated are nominal values of production units. There may be some deviations from these values in individual units.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 1,024,000 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Page 73
69
Appendix
Dimensions
Units: inches (mm)
9
19
/64 (236)
13
/32 (10)
13
/32 (10)
3
1
/8 (79)
1152/64 (300)
2
61
/64 (75)
1
21
/32
(41.7)
2
5
/16 (58.5)
1
15
/32
(37.3)
1
1
/2 (38)
131/32 (50)
1
9
/32 (32.5)
M4
4
7
/64 (104)
8
19
/32 (218)
1
15
/16 (49)
21
/32
(16.5)
261/64 (75)
4
21
/32 (118)527/64 (137.5)
M4
M4 M4
Page 74
70
16:9·············································································31, 32 3D MODE button ······························································14
Accessories ······································································11 AC socket ·········································································25 Adjustment buttons ····················································39, 40 Adjustment foot ································································28 All Reset ···········································································53 AREA ZOOM ····································································32 Aspect ratio ······································································31 Audio input ·······································································30 AUDIO 1, 2 terminals ························································23 Audio Mute ·······································································53 AUDIO OUT terminal ························································23 Auto Power Off ·································································50 Auto Restart ·····································································50 Auto Sync (Auto Sync adjustment) ····························34, 50 AUTO SYNC button··························································34 AV MUTE button ·······························································30
Background ······································································49 Batteries ···········································································15 Blue ··················································································49 BREAK TIMER button ······················································33 Bright ················································································43 BrilliantColor
TM
·································································43
Clock ················································································45 Closed Caption ·································································48 CLR Temp (Color Temperature) ········································43 C.M.S. ··············································································43 Color ·················································································43 Complete Menu ································································40 COMPUTER2 Select ························································52 COMPUTER/
COMPONENT1, 2 input terminals
·········21, 22
Contrast ············································································43 DHCP Client ·····································································55
DIN-D-sub RS-232C adaptor ···········································11 DLP
®
LinkTM ······································································53
DLP
®
LinkTM Invert ····························································53 DNR ··················································································44 Dynamic Range ································································45
Eco+Quiet···································································33, 44 ECO+QUIET button ··························································33 EDID Selection ·································································46 ENTER button ···································································39 Exhaust vent ·······························································12, 57
Fan Mode ·········································································51 Film Mode ·········································································44 Focus ring ·········································································27 FREEZE button ·································································34 FULL ·················································································31 FUNCTION button ····························································14 FUNCTION Button setting ················································53
HDMI terminal·····························································21, 22 HEIGHT ADJUST lever ·····················································28 H-Pos ···············································································45
Image shift ········································································47 Information ·······································································40 INPUT modes ···································································30 Input Search Start ····························································40 Intake vent ··································································12, 57 IP Address ········································································56
Kensington Security Standard connector ························13 Keycode ··········································································51 Keylock ············································································52 KEYSTONE button ··························································29 Keystone Correction ···················································29, 47
Lamp ················································································60 Lamp indicator ·································································58 Lamp Timer (Life) ······························································53 Lamp unit ·········································································61 Language (on-screen display language) ··························49 LAN terminal ·····································································25
L-CLICK/EFFECT button ············································33, 35 Lens shutter ································································26, 30 Link ···················································································56
MAC Address ···································································56 MAGNIFY buttons ····························································34 MENU button ····································································39 MONITOR OUT terminal ···················································23 MOUSE/Adjustment buttons ······································35, 39
NATIVE ··············································································31 Network ············································································54 NORMAL ····································································31, 32
ON button ·········································································26 Optional accessories ························································11 OSD Display ····································································48 Overscan ··········································································48
PAGE DOWN button ·························································35 PAGE UP button ·······························································35 Password ··········································································54 PDF···················································································10 Phase················································································45 Picture Adjustment ··························································42 Picture Mode ······························································34, 42 PICTURE MODE button ···················································34 POINTER button ·······························································33 Power cord ·······································································25 Power indicator ································································58 PRJ-ADJ1/2······································································50 PRJ Mode ···································································20, 49
Quick Start Menu ·····························································40 R-CLICK/RETURN button ··········································35, 39
Red ···················································································43 Remote control ·································································14 Remote control sensor ·····················································15 Replacing the lamp·····················································60, 61 Reset Network Setting ·····················································55 Resize ·········································································31, 47 RESIZE button ··································································31 Resolution·········································································45 Restart Network ·······························································55 RGB cable ········································································21 RS-232C terminal ·····························································24
SCR-ADJ ··········································································47 Screen Size and Projection Distance ·······························19 Security bar ······································································13 Setup Guide ·······························································27, 49 Sharp ················································································43 SIG-ADJ ···········································································45 Signal Info ·········································································46 Signal Type ·······································································45 Speaker ············································································50 SPOT button ·····································································33 STANDBY Audio Out ························································53 STANDBY button ······························································26 STANDBY Mode ·······························································53 STANDBY/ON button ·······················································26 Storage case ····································································63 Supplied accessories ·······················································11 S-VIDEO terminal ·····························································22 System Lock ·····································································51
TCP/IP ··············································································55 Temperature warning indicator ·········································58 Tint····················································································43
USB terminal ····································································35 Video Setup ······································································46
Video System ···································································46 VIDEO terminal ·································································22 VOL (Volume) buttons ·······················································30 V-Pos ················································································45 V-STRETCH ······································································32
Wall Color ·········································································49 Zoom ring ·········································································28
Index
Page 75
Loading...