Sharp LYNX 3D SH-03C Docomo Instruction Manual

Download

Page 1

‘10.11

Page 2

DOCOMO

W-CDMA and Wireless LAN System

Thank you for purchasing “LYNX 3D SH-03C”. Make sure thoroughly read this manual and the manuals included with optional accessories before and during use to ensure proper operation. If any of the contents in this manual are unclear, please contact number listed in “General Inquiries” on the back of this manual. SH-03C is designed to make your everyday life more convenient. Careful use will ensure a long service life.

Using the FOMA terminal

Because the FOMA terminal relies on radio signals,

it cannot be used in places with no signal (such as tunnels, underground or in buildings), in places with a weak signal or outside the FOMA service area. You may not use the FOMA terminal in the upper floors of a building even with no obstructions in sight. There may also be times when the signal is strong and you are not moving but the call is interrupted.

Make sure not to disturb others when using the

FOMA terminal in public places, places with many people or quiet places.

Because the FOMA terminal uses electrical signals,

it is possible for a third party to listen in on a conversation. However, since the W-CDMA system automatically applies privacy to every call, a third party that tries to listen in only hears static.

The FOMA terminal converts conversations into a

digital signal and sends it to the other party over the radio. If the signal cannot be reconverted properly by such as moving to an area with a weak signal, the voice may not be heard correctly.

Keep a separate memo and note information (e.g.

phonebook, calendar, notepad, voice memo, answering memo) stored in the FOMA terminal. DOCOMO shall not be liable for any loss of content due to a failure, repair, upgrade or other handling of the FOMA terminal.

As with PCs, some use-installed applications may

disrupt the stability of your FOMA terminal performance or unexpectedly transmit information via the Internet causing improper use of your location information and personal information stored in the FOMA terminal. Therefore, verify the supplier and operating conditions of the applications to be used before using them.

It is recommended to save the important data to the

microSD Card.

The FOMA terminal supports the FOMA Plus-Area

and the FOMA HIGH-SPEED area.

The FOMA terminal can be used only via the FOMA

network provided by DOCOMO and DOCOMO’s roaming area.

Download the latest information on this manual from the DOCOMO website.

“User’s Manual (in PDF format)” Download

http://www.nttdocomo.co.jp/english/support/ trouble/manual/download/index.html

※ The URL and contents of this manual are

subject to change without prior notice.

Checking operation method on the FOMA terminal

Select [Manual] in the application screen. Main contents described in this manual can be referred on the special web site (in Japanese only). In this online manual, you can find a description of the function you want to use using table of contents, index, and searching. The latest information on this manual is

described.

Page 3

Viewing/Searching this manual

This manual uses illustrations and icons to explain operations for proper phone use.

The screens and illustrations in this manual are

shown as examples. The actual screens and illustrations may differ.

Searching this manual

You can use the following ways to find explanations in this manual.

Index (nP. 134)

Indexed pages (nCover)

Contents

Application list

Note that “SH-03C” is referred to as “FOMA

terminal” in this manual.

This manual refers to microSD Card as

“microSD Card” or “microSD”.

Reproduction of this manual in part or in whole is

prohibited.

The contents of this manual are subject to

change without prior notice.

Search for function names or service names.

Search this manual using the index on the cover and the sides of pages.

nP. 2

nP. 43

Notation of keys and operation procedure

This manual refers to keys as simplified icons.

Actual key Notation in this manual

The notation and meaning of operation

procedure are shown below.

In the home screen, z/[Settings]/ [Call settings]

This manual describes the touch panel operation

when operation is available with both touch panel and key.

Viewing the display

The explanations in this manual are based on

default settings. The actual screens may differ depending on settings changed after purchase.

z (Refer to “Part names and functions” on P. 24)

Notation Meaning

In the home screen, press z b touch [Settings] b touch [Call settings]

Page 4

Viewing/Searching this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Notes on using SH-03C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Precautions (ALWAYS FOLLOW THESE DIRECTIONS) . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Handling precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Basic package and main optional parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Before Using the Handset P. 23

Call/Network Services P. 49

Various Settings P. 59

Mail/Browser P. 71

Part names and functions, UIM, microSD Card, Battery pack, Charging, Power on/off, Startup Guide application, Initial setting, Screen display/icon, Basic operation, Home screen, Character entry, Reset FOMA terminal

Make/Receive a call, Redial/Incoming History, Phonebook, Network services

Profile, Energy saving setting, Wireless & networks, Call settings, Sound & display, USB connection, Location & security, Applications, Accounts & synchronization, Privacy, microSD & phone storage, Search, Language & keyboard, Accessibility, Text-to-speech, Date & time, About phone

Mail, sp-mode mail, Gmail, SMS, Browser

Contents/Precautions

Page 5

Multimedia P. 75

Convenient Functions P. 83

Overseas Use P. 107

Appendix/Index P. 111

Camera, Gallery (3D), Contents Manager, MusicPlayer

GPS function, Compass, 1Seg, Osaifu-Keitai, Calendar, Alarm/ Timer, Notepad, Voice Recorder, Calculator, Dictionary, Android Market, docomo market, Infrared communication, Cooperation with Blu-ray Disc recorder, DLNA server settings, Bluetooth function, PC connection, OS version upgrade

International roaming (WORLD WING), Available services, Before use, Settings to use, Make/Receive a call

Options and related devices, Troubleshooting (FAQ), Warranty and After-Sales Service, Software Update, Main specifications, Specific Absorption Rate (SAR) of mobile phone, Export Administration Regulations, Intellectual Property Right, Index

Contents/Precautions

Page 6

Notes on using SH-03C

This FOMA terminal does not support i-mode

functions (connection to i-mode site (broadcast), i-appli, etc.).

Google applications and its service contents

are subject to change without prior notice.

This FOMA terminal automatically performs

communication for some functions, for example, to synchronize data, check the latest software version or maintain connection with the server. Also, operations such as watching videos cause a large volume of packet to be transmitted. Subscription to “Pake-hodai double/Pake-hodai simple” or other flat-rate packet transmission services is highly recommended (In subscribing to “Pake-hodai double/Pake-hodai simple”, the maximum charge is reached in a short period of time).

Setting this FOMA terminal to manner mode

does not mute sounds (camera shutter sound, etc.) other than the ring tone, operation sound, and various notification sounds.

For details on checking your phone number

(own number) nP. 60

For details on software version of your FOMA

terminal nP. 70

New functions may be added to this FOMA

terminal and the operation method may change by upgrading the OS version. Check the DOCOMO website for the latest information of additions and changes.

If the OS is upgraded, some applications that

used in the previous OS version may not be available or some unintended bugs may occur.

Read the terms of use of Google Inc. for

details on Google services. Also, read each terms of use for details on other web services.

If your FOMA terminal is lost, change your

each account password using a PC to prevent other persons from using Twitter, mixi, and Google services such as Google Talk, Gmail, Android Market.

The FOMA terminal does not support

providers other than mopera U, Business mopera Internet (URL restriction) and sp-mode.

The FOMA terminal is available without

microSD Card. However, some data such as images shot with camera or voices recorded with Voice Recorder can be saved only to microSD Card. It is recommended that microSD Card be inserted to use the FOMA terminal.

Contents/Precautions

Page 7

Precautions (ALWAYS FOLLOW THESE DIRECTIONS)

Before use, read these “Precautions” carefully

and use your FOMA terminal properly. Keep this manual in a safe place for future reference.

These precautions contain information intended

to prevent bodily injury to the user and to surrounding people, as well as damage to property, and must be observed at all times.

The following symbols indicate the different degrees of injury or damage that may occur if information provided is not observed and the FOMA terminal is used improperly.

This symbol indicates that “death or serious bodily

Danger

Warning

Caution

injury may directly and immediately result from improper use”.

This symbol indicates that “death or serious bodily injury may result from improper use”.

This symbol indicates that “minor injury and/or property damage may result from improper use”.

The following symbols indicate specific directions.

Indicates a prohibited action.

Indicates not to disassemble the device.

Indicates not to handle the device with wet hands.

Indicates not to use the device near water or get it wet.

Indicates that instructions specified are compulsory (must be followed).

Indicates that the power cord must be unplugged from the outlet.

“Precautions” is explained in the following six sections.

Handling the FOMA terminal, battery pack,

adapters, and UIM (general) . . . . . . . . . . . . . P. 6

Handling the FOMA terminal. . . . . . . . . . . . . P. 7

Handling battery pack . . . . . . . . . . . . . . . . . P. 10

Handling adapters. . . . . . . . . . . . . . . . . . . . P. 11

Handling UIM . . . . . . . . . . . . . . . . . . . . . . . P. 13

Handling near electronic medical equipment

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P. 13

Contents/Precautions

Page 8

Handling the FOMA terminal,

Danger

Warning

battery pack, adapters, and UIM (general)

Do not use, store or leave the equipment in locations subject to high temperatures, such as near a fire, in direct sunlight or

May cause fires, burns or bodily injury.

May cause fires, burns, bodily injury or electric shock.

inside a car on a hot day.

Do not place the equipment inside cooking appliances such as microwave ovens or pressure cookers.

Do not attempt to disassemble or modify the equipment.

Do not get the equipment wet with water, drinking water, pet urine, etc.

Use only the battery packs and adapters specified by NTT DOCOMO for use with the FOMA terminal.

Do not subject the equipment to strong impacts or throw it.

May cause fires, burns, bodily injury or electric shock.

Do not allow conductive materials (such as metal objects and pencil lead) to come into contact with the charger terminal, external device terminal or earphone/ microphone terminal. In addition, do not insert such

May cause fires, burns, bodily injury or electric shock.

May cause fires or burns.

May cause a gas explosion or fire. To use Osaifu-Keitai in locations such as gas stations, make sure to turn off the power in advance (If the Osaifu-Keitai lock setting is activated, disable the lock before turning off the power).

objects.

Do not cover or wrap the equipment with bedding, etc. when using or charging.

Make sure to turn off the FOMA terminal and not to charge the battery in locations such as gas stations where flammable gas is generated.

Contents/Precautions

Page 9

If you notice anything unusual,

Caution

Warning

such as an unusual odor, overheating, discoloration or deformation during use, charging or storage, immediately follow the instructions below. Unplug the power cord from

the outlet or cigarette lighter socket.

Turn off the FOMA terminal. Remove the battery pack

May cause fires, burns, bodily injury or electric shock.

May fall and cause injury.

May cause fires, burns or electric shock.

May result in bodily injury.

from the FOMA terminal.

Do not leave the equipment on unstable surfaces, such as on a wobbling table or sloped surface.

Do not store the equipment in locations that are subject to humidity, dust or high temperatures.

If being used by a child, have a guardian teach him/her the proper handling procedures. In addition, check that the child is using the equipment as directed.

Keep the equipment out of the reach of young children.

A young child may swallow the equipment or suffer other bodily injury.

Be very careful when using the FOMA terminal connected to adapters repeatedly or for long

The FOMA terminal, battery pack or adapters may become warm if 1Seg is used for a long time while charging. Touch high temperature areas for a prolonged period of time may cause skin irritations, itchiness or low-temperature burn in some people.

periods of time.

Handling the FOMA terminal

Do not aim the infrared port towards the eyes.

May cause eye injury.

Do not aim the infrared port towards home electric appliances with an infrared device during infrared

May interfere with the operation of infrared devices and cause an accident.

communication.

Contents/Precautions

Page 10

Do not point the illuminated

Picture Light

light directly at someone’s

Do not use Picture Light near people’s faces. Eyesight may be temporarily affected leading to accidents. Precautions: The picture light source used for this product may emit the light over the safety level for eyes when operations such as undirected adjustments are intentionally made. Therefore, do not disassemble the terminal.

eyes.

EN60825-1:1994 A1:2002 & A2:2001

CLASS1 LED Product

CAUTION:

Use of controls, adjustments or performance of procedure other than those specified herein may result in hazardous radiation exposure. As the emission level from Picture Light LED used in this product is harmful to the eyes, do not attempt to disassemble the cabinet. Servicing is limited to qualified servicing station only.

Do not allow water or other liquids, metal, flammable material or other foreign objects to enter the UIM or microSD Card port on the

May cause fires, burns, bodily injury or electric shock.

FOMA terminal.

Contents/Precautions

Do not shine the light at anyone driving a car or other vehicles.

May prevent a driver from driving safely and cause a traffic accident.

Turn off the FOMA terminal in areas where the use of mobile phones is prohibited, such as

May interfere with the operation of electronic devices and electronic medical equipment. Follow the instructions given by the respective medical facilities regarding the use of mobile phones on their premises. In addition, actions such as using on a mobile phone aboard aircraft are prohibited and punishable by law.

in aircraft or hospitals.

Keep the FOMA terminal away from the ears during a call in which hands-free is set or while the ring tone is ringing. When you attach the earphone/ microphone, etc. to the FOMA terminal to play games or music,

Excessive high volume may damage your hearing. Also it may prevent you from hearing the ambient sounds and cause an accident.

Earphone Signal Level

The maximum output voltage for the music player function, measured in accordance with EN 50332-2, is

33.0 mV.

do not make the volume too loud.

Page 11

If you have a weak heart, take

Caution

extra precautions when setting functions such as the vibrator and ring tone volume for

May have harmful effects on your heart.

incoming calls.

If you are using electronic medical equipment, contact the respective manufacturer or vendor to check whether the operation of the equipment is

May interfere with the operation of electronic medical equipment, etc.

affected by signals.

Turn the FOMA terminal off near high-precision electronic devices or devices that use

May interfere with the operation of electronic devices.

weak electronic signals.

Take particular care with the following devices

Hearing aids, implanted cardiac pacemakers, implanted cardioverter-defibrillators or other electronic medical equipment. Fire alarms, automatic doors, and other equipment controlled by electronic signals. If you use an implanted cardiac pacemaker, implanted cardioverter-defibrillator or other electronic medical equipment, contact the respective manufacturer or vendor to check whether the operation of the equipment is affected by signals.

In case that the display part or camera lens is damaged, make sure to pay attention to a broken glass and the exposed

The surface of the display is covered by a protective film or the surface of camera lens are covered by a plastic panel so as to minimize the possibility of glass scattering. However, touching the broken or exposed parts may cause injury.

inside of the FOMA terminal.

Do not swing the FOMA terminal by its antenna, strap,

May hit you or others around you, resulting in bodily injury.

etc.

Do not use the damaged FOMA terminal.

May cause fires, burns, bodily injury or electric shock.

If the display is broken and the liquid crystal then leaks, do not get the liquid on your skin

May result in loss of eyesight and harm to your skin. If the liquid comes into contact with your eyes or mouth, immediately rinse your eyes or mouth with clean water and see a doctor. If the liquid comes into contact with your skin or clothes, immediately wipe it off with alcohol, and wash with water and soap.

(face, hands, etc.).

Contents/Precautions

Page 12

On the surface of the display,

Danger

there is a protective film for securing the safety (for preventing the reinforced glass panel from shattering) in case of the damage caused by a drop, impact, etc. Do not forcibly peel

Using the FOMA terminal with the film removed may cause a bodily injury when the display is damaged.

off or scratch this film.

If you use the FOMA terminal in an automobile, contact the automobile manufacturer or vendor to check whether the operation of the electronic

May interfere with the operation of electronic equipment in some vehicle models. In such cases, stop using the FOMA terminal.

equipment is affected by signals.

Use of the FOMA terminal may cause skin irritations such as itchiness, rashes or eczema in some people. If this occurs, immediately stop using the FOMA terminal and seek

For details on materials of each part n“Material list” on P. 15

medical treatment.

Look at the display in a well-lit place, keeping a certain

Otherwise, eyesight may be decreased.

distance from the screen.

Handling battery pack

Check the type of battery using the information printed on the battery pack label.

Contents/Precautions

Label Battery type

Li-ion00 Lithium-ion

Do not touch terminals with metallic objects such as wires. In addition, do not carry or store the battery pack with

The battery pack may catch fire, explode, overheat or leak.

metallic necklaces, etc.

Check that the battery pack is facing the correct direction before you attach it to the FOMA terminal. If you are having difficulty fitting the battery pack to the FOMA terminal, do not use excessive pressure to force the battery

The battery pack may catch fire, explode, overheat or leak.

into place.

Do not throw the battery pack into a fire.

The battery pack may catch fire, explode, overheat or leak.

Do not puncture, hit with a hammer or step on the battery

The battery pack may catch fire, explode, overheat or leak.

pack.

Page 13

If the battery fluid, etc. comes

Warning

Caution

Warning

into contact with your eyes, do not rub your eyes but immediately rinse your eyes with clean water. Then seek

May result in loss of eyesight.

The battery pack may catch fire, explode, overheat or leak.

The battery fluid is flammable and could ignite, causing a fire or explosion.

The battery pack may catch fire, explode, overheat or leak.

prompt medical treatment.

If any trouble such as a deformation or scratches caused by a drop is found, never use it.

If the battery pack leaks or emits an unusual odor, immediately stop use and move it away from any flame or fire.

Prevent your pet from biting the battery pack.

Do not dispose of used battery packs in ordinary garbage.

May cause fires or damage to the environment. Place tape over the terminals to insulate unnecessary battery packs, and take them to a docomo Shop, retailer or institution that handles used batteries in your area.

Do not use or charge a wet battery pack.

The battery pack may catch fire, explode, overheat or leak.

If the battery fluid, etc. leaks, do not get the liquid on your skin

May result in loss of eyesight and harm to your skin. If the liquid comes into contact with your eyes, mouth, skin or clothes, immediately rinse them with clean water. If the liquid, etc. comes into contact with your eyes or mouth, see a doctor immediately after rinsing your eyes or mouth.

(face, hands, etc.).

Handling adapters

Do not use if the adapter’s cord is damaged.

May cause fires, burns or electric shock.

Contents/Precautions

Page 14

Never use the AC adapter in humid locations such as a

May cause fires, burns or electric shock.

bathroom.

The DC adapter should only be used in negative grounded vehicles. Never use this adapter

May cause fires, burns or electric shock.

in positive grounded vehicles.

Do not touch adapters if you hear thunder.

May cause electric shock.

Take care not to short-circuit the charging terminal when connected to an outlet or cigarette lighter socket. Also, take care not to allow any part of your body (hands, fingers, etc.) to come into contact with

May cause fires, burns or electric shock.

the charging terminal.

Do not place heavy objects on the adapter’s cord.

May cause fires, burns or electric shock.

When plugging/unplugging the AC adapter into/from the outlet, do not allow metallic straps or other metallic objects to come

May cause fires, burns or electric shock.

into contact with the terminal.

Do not handle the cord and plug of the adapters with wet hands.

May cause fires, burns or electric shock.

Always use the specified power supply and voltage. When using overseas, use the AC adapter that is available

Using the incorrect voltage may cause fire, burns or electric shock. AC adapter: 100V AC DC adapter: 12/24V DC (for negative grounded vehicles only) AC adapter available overseas: 100 to 240V AC (Connect only with household AC outlet)

overseas.

If the fuse in the DC adapter blows, always replace it with a

May cause fires, burns or electric shock. Refer to the respective manuals for information on the correct fuse specifications.

fuse of the specified type.

Wipe off any dust on the power plug.

May cause fires, burns or electric shock.

Fully plug the AC adapter into the outlet.

May cause fires, burns or electric shock.

Contents/Precautions

Page 15

Always grasp the power plug

Caution

Warning

when unplugging the adapters from the outlet or cigarette lighter socket. Do not forcibly

May cause fires, burns or electric shock.

pull by the adapter’s cord.

Unplug the power cord from the outlet or cigarette lighter socket

May cause fires, burns or electric shock.

when not using for a long time.

Should water or other liquids enter the adapters, remove the power plug from the outlet or cigarette lighter socket

May cause fires, burns or electric shock.

immediately.

Always unplug the power plug from the outlet or cigarette lighter socket before cleaning

May cause fires, burns or electric shock.

the adapters.

Handling UIM

Be careful with the cutting surface when detaching the

May cause bodily injury.

UIM.

Handling near electronic medical equipment

The precautions detailed here conform to the guidelines drawn up by the Electromagnetic Compatibility Conference Japan, regarding the protection of electronic medical equipment from signals emitted by mobile phones.

Observe the following in hospitals or other medical

Electromagnetic signals may have harmful effects on the operation of implanted cardiac pacemakers and implanted cardioverter-defibrillators.

facilities.

Do not take your FOMA terminal into operating rooms, ICUs (Intensive Care Units) or CCUs (Coronary Care Units). Turn off your FOMA terminal inside hospital wards. Turn off your FOMA terminal even when you are in an area outside hospital wards, such as a hospital lobby, since electronic medical equipment may be in use nearby. Where a medical facility has specific instructions prohibiting the carrying and use of mobile phones, observe those instructions strictly.

Turn off your FOMA terminal in crowded places such as rush-hour trains in case somebody nearby is using an implanted cardiac pacemaker or implanted cardioverter-defibrillator.

Contents/Precautions

Page 16

If you have an implanted cardiac

Caution

pacemaker or an implanted cardioverter-defibrillator, always carry or use your FOMA terminal at least 22 cm away from your

Electromagnetic signals may have harmful effects on the operation of implanted cardiac pacemakers and implanted cardioverter-defibrillators.

implant.

Patients receiving medical treatment away from a hospital or medical facility (e.g. home treatment) who are using electronic medical equipment other than implanted cardiac pacemakers or implanted cardioverter-defibrillators should consult the respective manufacturers for information regarding the effects of signals

Electromagnetic signals may have harmful effects on the operation of electronic medical equipment.

on the equipment.

Viewing 3D images

Do not view 3D images if you have had photosensitivity diseases or have heart diseases or if you are in bad shape, sleep-deprived, tired or

May cause an increase in symptoms.

under the influence of drink.

Contents/Precautions

When you see a double image plainly while viewing 3D images, stop using the FOMA

Viewing for a long time may cause eyestrain.

terminal.

When you feel trouble such as fatigue or discomfort while viewing 3D images, stop using

May cause sick feelings. Take a rest properly. Be extra careful to use in the environment that tends to shake the screen such as a train or a vehicle.

the FOMA terminal.

3D image viewing is intended for use by 6 years or older. When a child views a 3D image, his/her guardian should stay with him/her and take care

When a child views 3D images, he/she may get sick suddenly since it is difficult to notice the reaction for fatigue or discomfort.

whether he/she feels eyestrain.

To protect the growth process of children’s eyes, infants and elementary and junior high school students should refrain from viewing 3D images for a

Healthy growth of eyesight may be affected.

long time.

When you feel eyestrain, headache or sickness that is similar to carsickness after long viewing of 3D images, stop

Concern about avoiding continuous viewing by resting your eyes or seeing faraway.

viewing.

Page 17

Material list

Part

Display side

Surrounding section of display side

Sides

Back cover

Radio frequency preventing sticker

Operation key

1Seg antenna

Metal section of 1Seg antenna

Brace of 1Seg antenna

Earphone/Microphone terminal

Surrounding section of earphone/microphone terminal

External connector terminal

External connector terminal cover

Material/Surface

treatment

Reinforced glass/ Shatterproof sheet of surface

ABS resin/UV clear coating for surface

PA resin/UV coating for surface

ABS resin/UV coating for surface

Magnetic sheet/PET sheet for surface

PC resin/UV coating for surface

PA resin/UV coating for surface

SUS/Ni plating

zinc die-cast/Ni plating

Phosphor bronze/ Gold plating

PA resin

SUS/Ni plating

Elastomer resin/ Urethane coating for surface

Part

Camera/Infrared port panel

Surrounding of camera/ infrared port panel

Shooting LED ABS transparent resin

Picture Light ABS transparent resin

Inside back cover ABS resin

Speaker

FOMA antenna

Metal section of FOMA antenna

Inside microSD Card slot SUS/Ni plating

UIM tray POM resin

Battery storage side

Screw

Battery terminal connector LCP

Battery terminal

Battery pack

Battery pack terminal section

Material/Surface

treatment

PMMA resin/Hard coating

ABS resin/UV coating

Polyester/Surface dyeing

PC resin/Two pack coating

ABS resin/Gold plating, Two pack coating

PET/Glass epoxy board

Steel/Ni plating, Black Ni plating, Trivalent chromate

Copper alloy/Gold plating

PC resin/Spark erosion

Copper alloy/Full surface Ni with plating base, Gold plating

Contents/Precautions

Page 18

Handling precautions

General notes

Do not expose to water.

The FOMA terminal, battery pack, adapter and UIM are not waterproof. Do not use in humid or steamy areas such as bathrooms and avoid exposing to rain and other forms of moisture. If the FOMA terminal is carried close to skin, perspiration may cause internal components to corrode and result in malfunction. Note that if problem is found to be due to moisture, handset and parts are not covered by warranty and in some cases may be irreparable. Even where repairs are possible, repair charges will be incurred since damage is not covered by warranty.

Clean only with a soft and dry cloth (such

as the type used for eyeglasses).

･

Forceful rubbing of LCD with a dry cloth may scratch LCD surface.

･

Note also that LCD coating may stain if moisture or soiling is left on the surface for a long period.

･

Never use chemicals such as alcohol, thinners, benzene or detergents, as these agents may erase the printing on the handset or cause discoloration.

Occasionally clean terminals with a dry

cotton swab, etc.

Unclean terminals may result in poor connections and loss of power. Keep terminal clean with a dry cotton swab, etc. Take care of the terminal while cleaning it.

Do not place the handset near an air

conditioning vent.

Condensation formed due to rapid changes in temperature may cause internal corrosion and lead to malfunction.

Do not apply excessive force to the FOMA

terminal and battery pack when using them.

Carrying the handset in a tightly packed bag or sitting on the handset in your pocket may cause a damage to display, other internal components or battery pack or result in malfunction. Keeping an external connector device plugged into the external connector terminal or earphone/ microphone terminal may cause a damage to the connector or result in malfunction.

Do not rub or scratch the display with

metal, etc.

May scratch the handset and cause malfunction or damage.

Read the respective manuals supplied

with the FOMA terminal and adapters carefully.

Notes about the FOMA terminal

Do not forcefully press a surface of the

touch panel or operate with a pointed object such as a fingernail, ballpoint pen, pin, etc.

May damage the touch panel.

Avoid using the handset in extremely high

or low temperatures.

Use the FOMA terminal within the range of a temperature between 5°C and 35°C and a humidity between 45% and 85%.

Contents/Precautions

Page 19

Using the handset close to landline

phones, TVs or radios may have harmful effects on the operation of such equipment. Move as far away as possible from such items before use.

Keep a separate memo and note

information stored in the FOMA terminal.

DOCOMO shall not be liable for any loss of content.

Do not drop or otherwise subject the

FOMA terminal to severe impact.

May damage the handset and cause malfunction.

When connecting an external connector

device to the external connector terminal or earphone/microphone terminal, do not put it in obliquely or do not pull it while it is plugged in.

May damage the handset and cause malfunction.

The FOMA terminal becomes warm during

using or charging but this is not a malfunction.

Do not leave the camera in direct sunlight.

May cause discoloration or burn-in.

Use the FOMA terminal with the external

connector terminal cover on.

Dust, water and others enter inside and cause a malfunction.

Do not use the FOMA terminal without the

back cover.

May detach the battery pack or cause malfunction or damage.

While using a microSD Card, do not

remove the card or turn off the FOMA terminal.

May cause data loss or malfunction.

Never place a magnetic card near the

FOMA terminal.

The stored magnetic data in cash cards, credit cards, telephone cards, floppy disks, etc. may be erased.

Never place magnetized items near the

FOMA terminal.

Putting highly magnetized items closer may cause an error.

Notes about battery pack

Battery pack is a consumable product.

Though usage time varies with use, change battery if battery level is extremely low even after fully charged. Purchase a specified new battery pack.

Charge battery in areas where ambient

temperature is between 5°C and 35°C.

The usage time for a battery pack

depends on the usage and deterioration of battery pack.

Depending on usage, the battery pack

may swell as it approaches the end of its service life, but this will not cause problems.

Note the following when the battery pack

is stored.



The storage with the battery pack fully charged (immediately after charging is completed)



The storage with no battery level (cannot turn the

FOMA terminal on) May lower the performance or shorten the life of the battery pack. The second level of the battery pack icon or approximately 40% is recommended as the battery level for storage.

Contents/Precautions

Page 20

Notes about adapters

Charge battery in areas where ambient

temperature is between 5°C and 35°C.

Do not charge battery pack in the

following locations.



Areas with high humidity or dust or in areas exposed to strong vibrations



Close to landline phones, TVs, radios, etc.

Adapters may become warm during

charging but this is not a malfunction.

Do not use DC adapter to charge battery

when the car engine is not running.

May cause car battery to run down.

When using an outlet with a feature to

prevent the plug from being removed accidentally, follow instructions in the outlet user’s guide.

Do not subject to strong force or impacts.

Also, do not disfigure the charger terminals.

May cause a malfunction.

Notes about UIM

Do not apply unnecessary force when

inserting/removing the UIM.

Customer is responsible for malfunctions

arising from inserting UIM into a different IC card reader/writer.

Always keep IC area clean. Clean only with a soft and dry cloth (such

as the type used for eyeglasses).

Keep a separate memo and note

information stored in the UIM.

DOCOMO shall not be liable for any loss of content.

To protect the environment, please take

any unnecessary UIMs to a docomo Shop or retailer.

Do not damage, touch haphazardly or

short-circuit the IC.

May cause data loss or malfunction.

Do not drop or otherwise subject the UIM

to severe impact.

May cause a malfunction.

Never bend the UIM or place heavy

objects on it.

May cause a malfunction.

Do not insert the UIM to the FOMA terminal with a label or sticker attached on the card.

May cause a malfunction.

Notes on using Bluetooth function

The FOMA terminal supports the security

function that meets the Bluetooth specification for the security during communication using Bluetooth function. However, the security may not be sufficient depending on the configuration. Take care of the security while making communication using Bluetooth function.

Even if any leak of data or information

occurs while making communication using Bluetooth function, DOCOMO shall not be liable for any loss of content.

With the FOMA terminal, use headset,

hands-free, audio, object push, serial port and phone book access. Also, the audio/ video remote-control may be available depending on the audio (only with compatible Bluetooth devices).

Contents/Precautions

Page 21

Radio frequencies

① ②

③

④

The radio frequencies the Bluetooth function of the FOMA terminal uses are as follows.

①

2.4: This radio equipment uses the 2.4 GHz band.

②

FH: The modulation system is the FH-SS system.

③

1: The estimated coverage distance is 10 m or less.

④

2400 MHz and 2483.5 MHz are used and the frequencies for mobile object identifiers shall not be avoided.

: All radio frequencies between

Cautions on using Bluetooth devices

Bluetooth operates at radio frequencies assigned to the in-house radio stations for a mobile object identifier that have to be licensed and is used in production lines of a factory, specific unlicensed low power radio stations, and amateur radio stations (hereafter, referred to “another radio station”) in addition to industrial, scientific, medical devices or home electric appliances such as microwave ovens.

1. Before using this product, make sure that “another radio station” is not operating nearby.

2. If radio interference between this product and “another radio station” occurs, avoid interference by moving immediately to another place or “turning off the power”.

3. Contact the number listed in “General Inquiries” on the back of this manual for further details.

Notes about wireless LAN (WLAN)

Wireless LAN

Do not use wireless LAN near magnetic devices such as electric appliances or AV/OA devices or in radio waves.

･

Magnetism or radio waves may increase noises or disable communications (especially when using a microwave oven).

･

When used near TV, radio, etc., reception interference may occur or channels on the TV screen may be disturbed.

･

If there are multiple wireless LAN access points nearby and the same channel is used, search may not work correctly.

Radio frequencies

The radio frequencies the WLAN-installed devices use are indicated on the battery storage section. The following are the descriptions:

⑤

③

④

①

②

Contents/Precautions

Page 22

①

2.4: This radio equipment uses the 2400 MHz band.

②

DS: The modulation system is the DS-SS system.

③

OF: The modulation system is the OFDM system.

④

4: The estimated coverage distance is 40 m or less.

⑤

between 2400 MHz and 2483.5 MHz are used and the frequencies for mobile object identifiers

shall not be avoided. Available channels for SH-03C’s wireless LAN are between 1 to 13. Note that other channel access points cannot be connected. Available channels vary depending on the country. For use in an aircraft, contact the airline beforehand. There are restrictions on the use of wireless LAN in some countries or regions such as France. If you intend to use wireless LAN overseas, check the local laws and regulations beforehand.

: All radio frequencies

Cautions on using 2.4 GHz devices

WLAN-installed devices operate at radio frequencies assigned to the in-house radio stations for a mobile object identifier (radio stations requiring a license) used in production lines of a factory, specific unlicensed low power radio stations (radio stations requiring no license), and amateur radio stations (radio stations requiring a license) in addition to industrial, scientific, medical devices or home electric appliances such as microwave ovens.

1. Before using this device, make sure that the in-house radio stations for a mobile object identifier, specific unlicensed low power radio stations and amateur radio stations are not operating nearby.

2. If the device causes harmful radio interference to the in-house radio stations for a mobile object identifier, immediately change the radio frequency or stop use, and contact the number listed in “General Inquiries” on the back of this manual for crosstalk avoidance, etc. (e.g. partition setup).

3. If the device causes radio interference to specific unlicensed low power radio stations for a mobile object identifier or amateur radio stations, contact the number listed in “General Inquiries” on the back of this manual for further details.

FeliCa reader/writer

The FeliCa reader/writer function in the

FOMA terminal uses weak electric waves in the handling of which does not require a license of radio station.

The frequency in use is the 13.56 MHz

band. When another reader/writer is being used nearby, keep enough distance from it. Make sure that there is no radio station using the same frequency band in the nearby area.

Contents/Precautions

Page 23

Viewing 3D images

Keep a display parallel to your eyes when

watching 3D images.

When watching 3D images, hold the

FOMA terminal in front of your face and keep it approximately 30 cm away. The floating image or image which has depth appears.

There are differences in feelings about

stereoscopic effect of a 3D image among individuals.

Caution

Never use the FOMA terminal that is

modified. Using a modified device violates the Radio Law.

The FOMA terminal has acquired the certification of conformity with technical regulations for the specified radio station based on the Radio Law, and the “Technical Conformity Mark ” is printed on the model nameplate of the FOMA terminal as a proof. If the screws of FOMA terminal are removed and a modification is given to the inside, the certification of conformity with technical regulations will become invalid. Never use the FOMA terminal without the valid certification. Doing so violates the Radio Law.

Be careful when using the FOMA terminal

while driving a motor vehicle.

Using a mobile phone in hand while driving is regarded as a punishable act. However, the punishment has no application in some cases such as when rescuing sick and injured people or maintaining public safety.

Use the Bluetooth function only in Japan.

The Bluetooth function in the FOMA terminal conforms to the domestic radio wave standards and is authorized. Using the function overseas may result in punishment.

Use the wireless LAN (WLAN) function

only in Japan.

The wireless LAN function in the FOMA terminal conforms to the domestic radio wave standards and is authorized. Using the function overseas may result in punishment.

Use the FeliCa reader/writer function only

in Japan.

The FeliCa reader/writer function in the FOMA terminal conforms to the domestic radio wave standards. Using the function overseas may result in punishment.

Be careful not to connect the FOMA

terminal to PC using the microUSB cable for PC (sample) in areas where the use of mobile phones is prohibited.

Power may turn on automatically.

Contents/Precautions

Page 24

Basic package and main optional parts

SH-03C terminal

(includes warranty and Back Cover SH46)

■ Basic package

microSD Card (2 GB) (sample)

(includes user’s guide)

Battery Pack SH25

Manual (Japanese version)

FOMA charger micro USB adapter SH01

microUSB cable for PC (sample)

(includes user’s guide)

FOMA AC Adapter 01/02

(includes warranty and user’s guide)

For details on other optional parts nP. 112

microSD Card is inserted to

the FOMA terminal by default.

■ Main optional parts

Contents/Precautions

Manual

Page 25

Before Using the Handset

Part names and functions. . . . . . . . . . . . . . . . . 24

UIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

microSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Turning power on/off. . . . . . . . . . . . . . . . . . . . . 32

Startup Guide application . . . . . . . . . . . . . . . . . 32

Initial setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Viewing screen display/icons . . . . . . . . . . . . . . 37

Basic operation. . . . . . . . . . . . . . . . . . . . . . . . . 38

Home screen . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Character entry. . . . . . . . . . . . . . . . . . . . . . . . . 46

Resetting the FOMA terminal . . . . . . . . . . . . . . 48

Page 26

Part names and functions

1 Proximity sensor/Brightness sensor

Proximity sensor detects the distance to face

and prevents a false operation of touch panel during a call.

Brightness sensor detects brightness of the

surrounding area and adjusts the brightness of backlight. Do not cover the sensor area with your hand or a sticker. The sensor may not work properly.

2 External connector terminal 3 Display/Touch panel

The display for the FOMA terminal is

manufactured using high-precision technology, but it may occasionally contain dots that fail to light or that remain permanently lit. This is not a malfunction.

Depending on an application, the display may

automatically switch to horizontal/vertical view just by tilting the FOMA terminal.

4 Strap hole 5 Earpiece

Before Using the Handset

Page 27

6 Incoming/Charging lamp

Lamp to be illuminated/flashed differs

according to the function being used and situation.

7 z: Menu key

Displays available functions (menus) in a

screen.

8 |: Home key

Displays the center page of the home screen.

9 {: Back key

Returns to the previous screen.

a H: Power key

Use to set/disable the sleep mode, turn the

power on/off, etc.

b 1Seg antenna c x/y: Volume UP/DOWN key

Adjusts the volume in each function.

d }: Search key

Displays the quick search box.

e G: Shutter key

Shoots still pictures or moving pictures.

f FOMA antenna

FOMA antenna is built in. To receive in better

conditions, do not cover the antenna area with your hand.

g Earphone/Microphone terminal

Refer to http://k-tai.sharp.co.jp/peripherals/

earphone_support_sh-03c.html (in Japanese only) for details on the corresponding earphone/microphone.

h microSD Card slot i Speaker j Picture Light k Shooting LED l Camera m Infrared port n a mark

IC card is contained (It cannot be removed).

o Back cover

A radio frequency-preventing sticker is

attached on the back of the back cover. Do not peel off this sticker.

p RESET button

Reset the FOMA terminal.

q Mouthpiece/Microphone

UIM

A UIM is an IC card that records personal information, such as phone numbers.

You cannot make a call and use functions such

as packet transmission, etc. on the FOMA terminal without inserting a UIM.

In Japan, you cannot call to the emergency

number (110, 119 or 118) without inserting a UIM.

Before inserting or removing the UIM, turn off the

power, position the back facing upwards and remove the battery pack. Hold the FOMA terminal securely with your both hands.

■ Inserting UIM

Hook a fingertip on the catch on the

back cover and remove it upward

Catch

Before Using the Handset

Page 28

Hook a finger on the tab and pull

Tray

Ta b

Fit the notch of the UIM to that of the tray.

out the tray (1)

: Pull out the tray straight until it stops.

Hold the UIM with the IC (gold)

turned down and set on the tray (2)

Notch

IC (gold)

Push the tray all the way in (3)

Put the back cover onto the FOMA

terminal in the correct direction and attach it by securely pressing surroundings of the back cover

Before Using the Handset

■ Removing UIM

Hook a finger on the tab, pull the

tray out (1) and remove the UIM (2)

: Do not allow the UIM to fall when removing it.

Note that inserting or removing the UIM forcibly

may damage the UIM or deform the tray.

Refer to the UIM user’s guide for more

information on the UIM.

Do not misplace the UIM once it is taken out.

When the tray falls off, slide the tray in straight

along the guide rail.

Page 29

Securely close the back cover. If not closed

securely, the back cover may come off and the battery pack may fall out due to vibration.

The back cover may be damaged when

attaching or removing it forcibly. Make sure not to use unnecessary force.

microSD Card

You can save data in the FOMA terminal to microSD Card or import data in microSD Card to the FOMA terminal.

The SH-03C is compatible with microSD Card of

up to 2 GB and microSDHC Card of up to 32 GB (as of November 2010). Refer to http://k-tai.sharp .co.jp/peripherals/microsd_support_sh-03c.html (in Japanese only) for the latest information such as the manufacturer, available capacity, etc. of the microSD Card. In addition, some microSD Cards that are not provided in the sites may not operate. Note that the provided information is the information checked for operation. DOCOMO shall not be liable for all operations.

The size of a file that can be used is up to 2 GB. Do not turn off the FOMA terminal immediately

after inserting the microSD Card in the terminal (while writing information needed for FOMA terminal operation) or while editing data on the microSD Card. Data may be damaged and operation may not work properly.

Format unformatted microSD Cards on the

FOMA terminal before use (nP. 68). microSD Cards formatted by PCs or other devices may not be used properly by the FOMA terminal.

Data saved on the microSD Cards from other

devices may not be displayed or played on the FOMA terminal. Some data saved on the microSD Card from the FOMA terminal may not be displayed or played on other devices.

Back up the data saved in a microSD Card and

store in another place. DOCOMO shall not be liable for any loss or change of the saved data.

Before inserting or removing the microSD Card,

turn off the power, position the back facing upwards and remove the battery pack. Hold the FOMA terminal securely with your both hands.

■ Inserting microSD Card

Slowly insert the microSD Card

with the metal terminal side turned down

: Do not force the microSD Card in at an angle

or with the wrong side up. The microSD Card slot may be damaged.

: Push slowly with finger until a click is heard.

Before Using the Handset

Page 30

■ Removing microSD Card

Ta b

Gently push the microSD Card in

(1)

: Push until a click is heard. The microSD

Card springs back. Excessive force may damage the FOMA terminal or microSD Card.

Remove the microSD Card (2)

: Remove the card slowly by pulling it straight

out.

Battery pack

Use the Battery Pack SH25 exclusive to the

FOMA terminal.

For attaching or removing the battery pack, turn

off the power, position the back facing upwards, and hold the FOMA terminal securely with your both hands.

■ Attaching battery pack

Attach the battery pack

: With the recycle mark side turned up, place

the connector terminal of the FOMA terminal to that of the battery pack and attach the battery pack.

Connector terminal

With recycle mark side up

■ Removing battery pack

Remove the battery pack

: The battery pack has a tab that makes it

easy to remove. Hook a finger on the tab to prevent excessive force on it and remove the battery pack upward.

Before Using the Handset

Page 31

Using unnecessary force when attaching or

removing the battery pack may damage the connector terminal for the battery pack (charger terminal) on the FOMA terminal.

Charging

About charging

The battery pack is not fully charged at the time of purchase. Be sure to charge the battery using the FOMA charger micro USB adapter SH01, and the exclusive AC or DC adapter (sold separately) before use.

■ Cautions while charging

Do not charge for a long time with the power left

on. If the FOMA terminal is left on after charging is complete, the battery pack charge decreases. In that case, the AC or DC adapter charges the battery again. However, depending on the time when the FOMA terminal is disconnected from the AC or DC adapter, the battery charge level may be low or the battery may only be usable for a short time.

If the FOMA terminal is left for a long time even

after the charging is completed, the battery level may decrease.

When the battery is empty and terminal is

recharging, charging lamp may not illuminate immediately.

If the battery empty alert is displayed and the

power cannot be turned on, charge the battery for a while.

While charging, terminal may not turn on even

when charging lamp is illuminated in red. Charge longer and try turning power on again.

Frequently recharging the battery when its power

is still remaining enough may shorten the life of the battery pack. It is recommended to use the battery to a certain level before recharging.

■ Estimated charge time and lamp

display

The following figures are estimated times for charging an empty battery pack with the FOMA terminal turned off.

FOMA AC Adapter 01/02 Approx. 210 min

FOMA DC Adapter 01/02 Approx. 210 min

Charging lamp illuminates in red while charging,

and it turns off when charging is completed.

Check that the battery pack has been properly

attached when charging lamp flashes red. The lamp also flashes red when the battery pack has reached the end of its service life.

The battery pack can also be charged with the

FOMA terminal turned on (While charging, the battery icon appears with [w] superimposed).

When the battery becomes warm, charging may

automatically stop even if the battery has not been fully charged. Charging resumes after the temperature lowers to an appropriate temperature.

■ Estimated time of use when fully

charged

Continuous talk time

Continuous stand-by time

1Seg watching time

FOMA/3G

Approx. 270 min

FOMA/3G

When mobile: Approx. 360 hr At rest: Approx. 410 hr

Approx. 330 min

Before Using the Handset

Page 32

For details on time of use nP. 125

■ Battery pack service life

Battery pack is a consumable product. Service

time per charge is gradually reduced every time the battery is charged.

When service time per charge is reduced to

about half of the default time, this means that the battery pack is approaching the end of its service life. In such a case, it is recommended to replace the battery pack as soon as possible. Depending on usage, the battery pack may swell as it approaches the end of its service life, but this will not cause problems.

If 1Seg etc. is used while charging for a long

time, the service life of the battery pack may become shorter than estimated.

To prevent damage to the environment, bring

used battery packs to a docomo service counter, a docomo agent or a recycle center.

■ About AC adapter and DC adapter

Refer to user’s guide of FOMA AC Adapter 01/02

(sold separately), FOMA AC Adapter 01 for Global use (sold separately) or FOMA DC Adapter 01/02 (sold separately).

FOMA AC Adapter 01 covers only 100V AC.

FOMA AC Adapter 02/ FOMA AC Adapter 01 for Global use covers from 100 to 240V AC.

The shape of the plug for the AC adapter is for

100V AC (for domestic use). To use the AC adapter of 100 to 240V AC overseas, a conversion plug adapter that is compatible with the voltage of your country of stay is required. Do not use a transformer for use overseas to charge the battery.

Charging by using AC adapter/ DC adapter

[Read the user’s guides of FOMA AC Adapter 01/02 (sold separately) and FOMA DC Adapter 01/02 (sold separately)]

Insert the AC or DC adapter

connector horizontally into the external connector terminal of the FOMA charger micro USB adapter SH01 (1)

: Check the direction (front or rear) of the

connector, keep it parallel with the FOMA charger micro USB adapter SH01 and securely push all the way in until it clicks.

Open the external connector

terminal cover of the FOMA terminal and insert the microUSB plug of the FOMA charger micro USB adapter SH01 horizontally into the external connector terminal (2)

: Insert the microUSB plug horizontally with

the character side turned up.

Before Using the Handset

Page 33

microUSB plug (with

100V AC outlet

For AC adapter

Cigarette lighter socket

For DC adapter

the character side up) External connector

terminal (with the character side down)

External connector terminal

Connector (with the arrows side up)

: When charging is complete, remove the

microUSB plug horizontally from the FOMA terminal (1).

: When removing the connector from the

FOMA charger micro USB adapter SH01, always hold the release buttons on both sides (2) and unplug it horizontally (3).

When inserting the AC adapter

power plug into an outlet or inserting the DC adapter power plug into a car cigarette lighter socket, charging lamp illuminates and charging starts

When charging lamp turns off,

charging is complete

Release buttons

Do not forcibly insert or remove. May cause

damage to the external connector terminal, the microUSB plug and the connector.

Pull the adapter out of the outlet or cigarette

lighter socket if it will not be used for a long time.

Do not forcibly pull the external connector

terminal cover. May damage the cover.

Do not place objects near the FOMA terminal

when charging. May damage the FOMA terminal.

When using a DC adapter

The DC adapter should only be used in

negative grounded vehicles (12 and 24V DC).

Do not use with the car engine shut off. May

drain the car battery.

The DC adapter fuse (2A) is a consumable. For

replacement, purchase a new fuse at a local automobile supply shop.

Refer to the user’s guide of FOMA DC Adapter

01/02 for details.

Before Using the Handset

Page 34

Charging by using microUSB cable for PC

When the FOMA terminal is turned on, you can charge the FOMA terminal by connecting the FOMA terminal to a PC with the microUSB cable for PC (sample). Install the USB driver to the PC in advance. And

also enable USB battery charge (nP. 63). ･ Refer to “Manual for USB Driver Installation” in

PDF format in http://galapagossquare.com/ ?p=5208 (in Japanese only) for details on installing USB driver.

For details on connecting to a PC nP. 104

Turning power on/off

■ Turning power on

H (for at least 2 seconds)

■ Turning power off

H (for at least 1 second)/[Power

off]/[OK]

■ Sleep mode

The screen is off and the sleep mode is activated when H is pressed or the FOMA terminal is not in use for a set length of time. Press H in the sleep mode to deactivate the sleep mode.

■ Touch panel lock

When the power is turned on or the sleep mode is deactivated, the touch panel is locked. Keep touching [J] and slide it right into [K] to unlock.

Key operation in touch panel unlock screen

To set/disable manner mode: y (for at least 1

second)

To illuminate Picture Light: G (for at least

1 second) ･ Press any key or touch [J] to turn off.

To turn off power: H (for at least 2 seconds)

Startup Guide application

Startup Guide is an application to support beginners to learn operations or initial settings. Basic operation practice, basic setting, and term dictionary are included.

In the application screen, [Startup

Guide]

Before Using the Handset

Page 35

Initial setting

Changing screen display to English

In the home screen, z/[設定]

(Settings)/[言語とキーボード] (Language & keyboard)/[言語 (Language)を選択] (Select

language)/[English]

Setting access point

The access point for Internet connection is registered by default. You can add or change it if necessary. The access points of sp-mode and mopera U are registered by default. At the time of purchase, an access point of sp-mode is set for usual connection.

■ Checking access point in use

In the home screen, z/

[Settings]/[Wireless & networks]/[Mobile networks]/ [Access Point Names]

■ Setting access point additionally

Never set the MCC to other than 440 and the

MNC to other than 10. They do not appear on the screen.

In the home screen, z/

[Settings]/[Wireless & networks]/[Mobile networks]/ [Access Point Names]/z/ [New APN]

[Name]/enter the name of the

network profile to create/[OK] [APN]/enter the access point

name/[OK]

Enter other items required by

telecommunications carriers/ z/[Save]

If the settings of MCC and MNC are changed

and they do not appear on the screen, reset the settings or set the access point manually.

Resetting access point

Reset an access point to default setting.

In the home screen, z/

[Settings]/[Wireless & networks]/[Mobile networks]/ [Access Point Names]/z/ [Reset to default]

When sp-mode is not subscribed or if you failed

to perform automatic setting of access point due to signal status such as outside the service area etc., you are required to set the access point again manually.

Before Using the Handset

Page 36

sp-mode

sp-mode is an ISP owned by NTT DOCOMO for the Smartphone. In addition to the Internet connection, mail service with the same address you use on i-mode (@docomo.ne.jp) is available. sp-mode is a paid service that requires subscription. For details on sp-mode, refer to DOCOMO website.

mopera U

mopera U is an ISP owned by NTT DOCOMO. If you subscribe to mopera U, you can use Internet with easy setting. mopera U is a paid service that requires subscription.

■ Setting mopera U

In the home screen, z/

[Settings]/[Wireless & networks]/[Mobile networks]/ [Access Point Names]/[mopera

U(スマートフォン定額)] (mopera U(Smartphone flat-rate))/[mopera U

設定] (mopera U settings)

“mopera U 設定” (mopera U settings) is an

access point for mopera U settings. When you use the access point for setting mopera U, packet transmission charges are not incurred. Note that you can connect to only the initial setting screen or the change setting screen. For the details on mopera U settings, refer to the mopera U website.

To use “mopera U (Smartphone flat-rate)”,

subscription to “Pake-hodai double/Pake-hodai simple” is required. For details on mopera U (Smartphone flat-rate), refer to DOCOMO website.

Wi-Fi settings

Wi-Fi allows you to access the Internet using wireless LAN function. To use Wi-Fi, you need to connect to the wireless LAN access point (Wireless LAN base unit). Refer to the manual of your wireless LAN base

unit when using the access point at home.

Operate access point registration near the

access point.

Wireless LANs (IEEE 802.11b/g) use the same

frequency band (2.4 GHz) as the Bluetooth device. Therefore, using the wireless LAN device near a Bluetooth device may cause the radio interference, lowering of communication speed, noise or connection fail. In this case, turn off the Bluetooth device or keep the FOMA terminal and the wireless LAN device at least approximately 10 m away from the Bluetooth device.

Enable Wi-Fi function in advance (nP. 61).

In the home screen, z/

[Settings]/[Wireless & networks]/[Wi-Fi settings]

Select an item

Wi-Fi: Enable Wi-Fi function. Network notification: You get notified by the

notification icon when Wi-Fi network is detected.

Before Using the Handset

Page 37

Easy Wi-Fi registration: Register AOSS/

WPS-compatible access point with each method.

Auto login settings: You can set the handset

to log in DOCOMO Public Wireless LAN Service automatically when you come within its service area.

Add Wi-Fi network: Register access points

which are not compatible with AOSS/WPS manually.

: Available access points are displayed as

items in “Wi-Fi networks”. To connect, select an access point to be used/[Connect].

[Easy Wi-Fi registration]

The registration process takes a few minutes.

After completion of the registration of the access point, check that the proper connection to the access point is acquired.

[Auto login settings]

Separate subscription is required to use

DOCOMO Public Wireless LAN Service.

In some service areas, automatic login function

may be unavailable.

If you set the automatic login to [ON], the

handset logs in automatically when coming within the service area. Note that high charges may be incurred if your subscription is Mzone daily plan and you set the automatic login to [ON].

This function may become unavailable

according to change of the log-in page contents of DOCOMO Public Wireless LAN Service. In this case, log in via the browser.

■ Disconnecting

In the home screen, z/

[Settings]/[Wireless & networks]/[Wi-Fi settings]

Select the connected access

point/[Forget]

: Disconnect retaining the password.

When you terminated the connection with Wi-Fi

function disabled, enable Wi-Fi function to connect automatically if the previously connected access point is available.

Setting up mail account

In the application screen, [Email]

: Only when an account is not set, the account

setting screen appears.

Enter mail address and password/

[Next]

: Provider information is preset for some mail

accounts, and a receiving mail server and a sending mail server are automatically set.

: When you use an account whose provider

information is not preset, it is necessary to set a receiving mail server and a sending mail server manually. For details on those settings, contact the internet service provider you use.

Enter an account name and your

name/[Done]

Before Using the Handset

Page 38

The account which is registered first is

automatically given priority to normal use. To change the priority, set priority account for creating mail.

When you delete an account, all mails delivered

to that account are deleted. When there is any protected mail, the account cannot be deleted.

When the account type is Exchange, entering

“¥UsernameDomain” in the “Domain¥Username” area is required to set a receiving mail server manually depending on the provider to use. Contact the administrator of the server for details.

Setting up Google account, etc.

In the home screen, z/

[Settings]/[Accounts & sync]/ [Add account]

Select the account type

Set up an account

When activating the application that requires an

account without setting the account, the account setup screen appears.

When an account is set, Background data and

Auto-synchronization of Accounts & synchronization are enabled (nP. 67).

Keep a separate memo of the set account and

password.

■ Resetting your Google account

password

If you forget your Google account password, retrieve it.

In the application screen, [Browser]

Before Using the Handset

Enter “http://www.google.com/” in

the URL entry field/[Go]/[Sign in]/[Can’t access your account?]/follow the instructions on the screen

Using PhoneBookCopy

You can copy phonebook data to/from other FOMA terminals using microSD Card. Also, you can copy phonebook data stored in Google account to docomo account.

In the application screen,

[PhoneBookCopy]

: When you use this for the first time, you must

agree with “license agreement”.

■ Exporting phonebook to microSD Card

Insert microSD Card in advance.

In the PhoneBookCopy screen, [エ

クスポート] (Export)/[開始] (Start)/[OK]

: Phonebook data stored in docomo account

are saved to microSD Card.

■ Importing phonebook from microSD

Card

Insert microSD Card with phonebook data in

advance.

In the PhoneBookCopy screen, [イ

ンポート] (Import)

Page 39

Select a phonebook to import/[上

Status bar

Status icon

Notification icon

書き] (Overwrite)/[追加] (Add)/[OK]

: Imported phonebook data are saved in

docomo account.

■ Copying contact information stored in

Google account to docomo account

In the PhoneBookCopy screen,

[docomoアカウントへコピー] (Copy to docomo account)

Select a Google account to copy/

[上書き] (Overwrite)/[追加] (Add)/ [OK]

: Copied phonebook data are saved in

docomo account.

: You can copy phonebook data stored in the

FOMA terminal to docomo account in the same way as Google account.

When phonebook item names (phone number

etc.) stored in other FOMA terminals are different from those of this FOMA terminal, the item names may be changed or deleted. Also, the characters that can be registered in contact information are different in each FOMA terminal, so they may be deleted in copy destination.

Group information cannot be imported.

When you export phonebook to microSD Card,

you cannot copy phonebook data without name.

When you import phonebook from microSD

Card, you cannot read file which backed up collectively.

Viewing screen display/ icons

Viewing icons

Icons displayed on the status bar at the top of the screen give you various kinds of information, such as the status of the FOMA terminal or the presence of missed calls. You can check the detailed information by displaying the status panel. Two kinds of icons are displayed.

Notification icon

Status icon Displayed at the right side of the

Displayed at the left side of the status bar and notifying you of missed calls or new mails, etc.

status bar and notifying you of the status of the FOMA terminal such as current time or the battery level.

Before Using the Handset

Page 40

Using status panel

Touch the status bar

: Alternatively, keep touching the status bar

and slide down.

1 Details of notification icon

When there is a corresponding application,

touch the detailed information to activate the application.

2 Details of status icon

When there is a corresponding application,

touch the detailed information to activate the application.

3 Close bar

Touch or keep touching and slide up to close

the status panel.

4 Manner mode

Set manner mode.

5 VeilView

Set VeilView.

6 Running application

Display functions being activated as a list.

Basic operation

Operation of touch panel

You can operate by touching the touch panel (display) directly with your finger. Operations differ depending on the function and

screen in use.

Cautions when using the touch panel

The touch panel is designed to lightly touch

with your finger. Do not forcefully press with your finger or press with a pointed object (fingernail, ballpoint pen, pin, etc.).

In the following cases, the touch panel may

not work even if you touch it. May cause a malfunction.

Operation with a gloved finger Operation with a fingernail Operation with foreign objects placed on

the operation pad

Operation on the touch panel on which a

protective sheet or a sticker is put

■ Touch

Touch a key or an item displayed on the screen to select or set it.

Put your finger on the touch panel

and put it off

Before Using the Handset

Page 41

■ Touch for a while

When you touch the screen for a while, a menu may appear depending on the function and screen in use.

Keep your finger on the touch panel

■ Slide

Slide up/down while a menu is displayed etc. to scroll the screen. When you touch a menu or item by mistake, slide away from the menu or item to cancel the selection.

Keep your finger on the touch panel

and slide it

■ Quickly slide

Quickly slide to the left/right in the home screen etc. to switch pages.

Quickly slide your finger and put it

off

Put two fingers on the touch panel

and slide them with putting a distance between two fingers apart/ closer

Operation while using function

■ Switching the settings

When a check box is displayed beside the setting item, you can set it enabled/disabled or [ON]/[OFF] by touching it.

Example: Sound & display setting screen,

[0]: Enabled, [1]: Disabled

Alarm setting contents screen

■ Put a distance between two fingers

apart/closer

Put a distance between two fingers apart/closer while displaying an image etc. to zoom in/out.

■ Retrieving menu

When you press z or touch the screen for a while, functions (in a menu) available in that screen appear.

Before Using the Handset

Page 42

Example: Phonebook screen

Set item list

Home screen

Viewing home screen

The home screen appears when the FOMA terminal power is turned on. You can paste widget or activate applications by selecting shortcuts or application icons. Home screen has two statuses.

Desktop display

Application screen display

Quick menu, shortcut, widget or a folder is superimposed on wallpaper image. Desktop display has five

pages, and you can place shortcuts, widgets or folders in each page.

Application screen is displayed.

You can retrieve various functions from home

screen using following menu or shortcut.

Application screen

Quick menu Place a shortcut of application to

Shortcut Create a shortcut in the home

Widget Place widget in the home screen

Folder Place a folder in the home

You can move application icons/shortcuts/

widgets/folders by touching them for a while and slide it to the destination.

Loaded applications are displayed as icons in the application screen. Select an icon to activate an application. If you install a new

application, an icon is added to the application screen.

If you uninstall an application,

an icon is deleted. If an icon is deleted, other icons are moved over and aligned on the screen. However, icons in the next page are not moved.

quick menu to quickly activate an application.

screen to quickly activate a frequently used function.

to use easy functions such as calendar or compass in the home screen. The FOMA terminal supports

Droidget besides Android standard widget.

screen to display a data in the folder quickly and to store shortcuts into the folder.

Before Using the Handset

Page 43

･ If you keep touching them and slide to the left/

Desktop display

Application screen display

right edge of the page and stop, the previous/ next page is displayed and you can move them to another page.

If you delete the applications and widgets

installed by default, you can download them from the site (http://galapagossquare.com/) (in Japanese only).

4 Shortcut 5 Indicator

Indicates the page of the displayed desktop/

application screen.

You can display miniatures of all the screens

on the desktop by touching the indicator. Select a miniature to move to the page.

6 Quick menu 7 Application screen

Creating quick menu/shortcut by moving application icon

You can create up to three quick menus. If there

are already three, move or delete created quick menu and then create new quick menu.

In the application screen, touch an

icon for a while

Keep touching the icon and slide it

to the destination

: You can create a quick menu by sliding it to

the quick menu.

: You can create a shortcut by sliding it to

wallpaper.

1 Folder 2 Display/Hide application screen

Touch to display/hide an application screen.

3 Widget

Pasting shortcut/widget/folder

In the desktop, z/[Add]/

[Shortcuts]/[Widgets]/[Folders]

Select a type

: For Droidget compatible widget, [N] ([O]

when widget is pasted on the home screen) appears.

Before Using the Handset

Page 44

Deleting quick menu/shortcut/ widget/folder

In the home screen, touch quick

menu/shortcut/widget/folder for a while

Keep touching quick menu/

shortcut/widget/folder and slide it to [X]

Multi Assistant (Multitask)

If you cancel the use of function by pressing | etc., the function does not end and remains activated in background. Display running functions as a list and switch functions to use by using Multi Assistant (Multitask).

In the home screen, [W]

: Alternatively, | (for at least 1 second).

Select a function to be used

: To terminate a function: [Y]

The functions being activated in background

may end depending on the memory usage or application. Also, the display of running function on the Multi Assistant (Multitask) screen may change depending on the memory usage.

Searching information in the FOMA terminal and sites

In the home screen, }

: Quick search box appears.

Enter the keyword

: Search applications and data that start with

the entered character and display a list of them.

Select the search result

: Select a search result to activate the

corresponding application.

■ Searching sites by voice

In the quick search box, [!]

: Alternatively, [Voice Search] in the

application screen.

Enter the keyword by voice

: Browser is activated.

When voice is not recognized properly, touch

the keyword entry field in the quick search box to display a list of sound-alike keywords.

Using 3D menu

Applications compatible with 3D are displayed as a list. Various 3D functions are available with displayed applications. Enable Orientation of Sound & display in

advance (nP. 62). Also, set the 3D menu setting of the home screen menu to [ON].

Before Using the Handset

Page 45

If you play games and 3D images or watch for a

long time, the FOMA terminal becomes warm and the screen becomes dark. This is not a malfunction. The screen becomes bright again if you disable 3D display.

Video Camera does not support 3D moving

picture shooting.

Using 3D conversion function

When you convert an image whose copyright is owned by another person, such as recorded one with the FOMA terminal or acquired from another media, enjoy it by yourself and use it only within the range of your private purpose. Note that the use of it over the range can be violation of the copyright.

In the home screen, tilt the FOMA

terminal horizontally

Select an application

Application list

Application Description

Manual Main contents described in this

Startup Guide

manual can be referred on the special web site (in Japanese only). In this online manual, you can find a description of the function you want to use using table of contents, index, and searching.

An application to support beginners to learn operations or initial settings (nP. 32).

Application Description

PhoneBookCopy

Voice Search Search information of sites by

Phone Use Phone (nP. 50).

Address Book

Settings Set each item of the FOMA

Email Use Email (nP. 72). spモード

メール (sp-mode mail)

Gmail Use Gmail (nP. 74). Messaging Use SMS (nP. 74).

Browser Display a web site using packet

Camera Shoot still pictures (nP. 78).

Camera (3D photos)

Video Camera

Barcode reader

Business card reader

Information reader

Text reader Scan text using camera (nP. 81). Gallery(3D) Display images (nP. 81).

Transmit all contact information data between the FOMA terminal and another terminal (nP. 36).

voice (nP. 42).

Use Address Book (nP. 52).

terminal (nP. 60).

Send and receive mail using mail address of i-mode (nP. 73).

transmission or wireless LAN (nP. 74).

Shoot 3D still pictures (nP. 78).

Shoot moving pictures (nP. 79).

Scan bar codes using camera (nP. 79).

Scan business card using camera (nP. 80).

Scan information using camera (nP. 80).

Before Using the Handset

Page 46

Application Description

Contents Manager

MusicPlayer Play music (nP. 82).

Compass Checking present location and

One-Seg Watch 1Seg (nP. 86).

おサイフケータイ

(Osaifu-Keitai)

ToruCa

Calendar Manage the schedule (nP. 93).

Alarm/Timer Use Alarm, StopWatch, and Timer

Notepad Save a note (nP. 94).

Voice Recorder

Calculator Use a calculator (nP. 95). Dictionary Use a dictionary (nP. 95). Market Use Android Market (nP. 96).

docomo market

Receive by Infrared

メーカーサイト (Maker

site)

Built-in 3D Play pre-installed 3D images in the

Last 3D Play the latest played 3D image.

Manage data stored to the microSD Card (nP. 82).

azimuth (nP. 85).

Osaifu-Keitai can be used (nP. 91).

Display, search or update ToruCa (nP. 92).

(nP. 93).

Use Voice Recorder (nP. 94).

Use docomo market (nP. 97).

Receive data by infrared (nP. 99).

Connect to SHARP website (in Japanese only).

FOMA terminal.

Application Description

Latitude Use Google Latitude.

Maps Use Google Maps.

Navigation Use Google Maps Navigation.

Places Use Google Places.

Talk Use Google Talk.

millmo SH

Book store

You can check where a friend is on the map and share status messages by using it.

You can measure your present location, display road conditions in real time, and use the navigation function to check how to get to your destination in detail by using it.

You can search for a route from the present location to the destination by using it.

You can search for facilities near your present location according to genre by using it.

Google Talk is an instant message service provided by Google. You can communicate with other users in real time with FOMA terminal or on the website by using Google Talk.

Use millmo. millmo is an application that enables you to use various contents in sites such as music and video.

Use millmo Book Player for SH. You can purchase e-books such as comics and photo collections by connecting to commercial site of e-books and manage/view purchased e-books.

Before Using the Handset

Page 47

Application Description

Music Use millmo Media Player for SH.

Evernote Evernote is a service to save

Documents To Go

mixi for SH Use mixi. You can use mixi to

Twitter Use Twitter. You can use Twitter to

You can manage/play moving pictures in the FOMA terminal or play movie contents on web sites.

various information such as contents of web site, pictures you shot or note of ideas in the sever and to retrieve/view them when you need. You can save and view the information not only from the FOMA terminal but from a PC or other devices. To use this application, you

need to create an Evernote account.

When you use this application

for the first time, you must agree with “terms of service” and download Evernote application.

Packet transmission charge may

be incurred for downloading the application.

Display files such as Microsoft Word, Microsoft Excel, and Microsoft PowerPoint.

communicate with your friends through various services such as posting diary, uploading pictures, posting voice.

communicate with other people by sharing short messages on sites.

Application Description

UkiUkiView*Use UkiUkiView. UkiUki balloons

YouTube Use YouTube. YouTube is a free

Promise Mail (Trial)

3D SAKANA+

golfriend

(comments) and store information are registered to location information of place. They allow you to see information of the place shot in the camera mode or displayed in the map mode. Also, you can post UkiUki balloon to register information to location information.

online video streaming service. You can play, search, and upload videos.

Use promise mail. Scan the date

and time written in the message of the mail on sending it and automatically register a schedule to Google Calendar. You are required to satisfy the

following conditions to automatically register schedules to Google Calendar with Promise Mail. Put a comma (、) after entering

characters or numbers to specify the date and time.

Enter “<以上>。(<Period>.)” at

the end of a sentence.

A game in which you can view inside an aquarium displayed in 3D freely.

A 3D golf game.

Before Using the Handset

Page 48

Application Description

QWERTY keyboard

12 keyboard

ショットナビX 体験版

(Shot Navi X (Trial))

EDF3D mobile

Happy Decoration 3D for SH

* This is provided in Japanese.

GPS golf navigation application covering golf courses all over Japan.

A 3D action shooting game.

A game to make a fancy cake on the screen.

Character entry

Keyboard layouts

Switching keyboards

You can use the following two types of the

keyboards.

QWERTY keyboard

12 keyboard Several characters are assigned

In the character entry screen, [T]/

[Change keyboard(Portrait)]/ [Change keyboard(Landscape)]

Before Using the Handset

You can enter a displayed character by touching the character entry key. Use romaji for entry.

to one character entry key. Characters are switched every time the key pressed. You can enter characters

quickly by keeping touching a character entry key and slide up/down or to the left/right.

1 Character entry keys

Use to enter characters or numbers. The display of character entry keys changes

corresponding to the input mode or the setting of upper/lower case.

2 Alphabet/Shift key

Touch to enter half-width alphabet in

Hiragana-Kanji entry mode.

Touch to switch between upper/lower case

letters. Symbols that can be entered changes when switching.

3 Character key

Touch to change input modes.

4 Symbol key

Use to display the pictogram/symbol/emoticon

list.

5 Setting/Conversion key

Display setting menu. Convert input characters.

6 Cursor keys

Use to move the cursor or to change the

range of characters to be converted.

Page 49

7 Delete key

Conversion candidates field

Use to delete a character on the left side of

the cursor. When the cursor is on the beginning, delete a character on the right side of the cursor. When the cursor is on a character, delete the character.

8 Enter key

Use to confirm the entered characters or

insert a line break.

9 Riverse toggle/Undo key

Use to display characters assigned to the

same key in the inverse order.

Use to undo previous operation.

Entering characters

Example: When entering “文字”

In the character entry screen, enter

“もじ”

: To enter a displayed conversion candidate:

Touch the conversion candidate

: To confirm characters in hiragana: [OK]

[変換] (conversion)

: To broaden/restore the conversion

candidates field: [Q]/[P]

■ Wildcard Prediction

Conversion candidates are predicted by the number of the entered characters and appear. Enable Wildcard Prediction of iWnn IME - SH

edition in advance (nP. 68).

This function is available in the Hiragana-Kanji

entry mode and the Half-width alphabet entry mode.

Example: When entering “アナウンス”

In the character entry screen, enter

“あな” [S]/[S]/[S]

: Each time you touch [S], [*] is entered and

the predictive conversion candidates appear according to the number of characters.

In the conversion candidates field,

select “アナウンス”

■ Switching input modes

Switch input modes according to types of characters to enter.

In the character entry screen, touch

character key for a while

: Touch character key to switch input modes in

the order of Hiragana-Kanji b Half-width alphabet b Half-width numeric.

Select input mode

Select “文字”

Before Using the Handset

Page 50

■ Entering pictograms/symbols/

emoticons

Unavailable characters cannot be entered

depending on applications.

In the character entry screen,

symbol key

Select a pictogram/symbol/

emoticon

■ Inputting kuten codes

You can use four-digit kuten codes assigned to each character for entering kanji, hiragana, katakana, symbol or alphanumeric characters. Refer to “Kuten Code List” in PDF format in

DOCOMO website for details on “Kuten Code List”.

In the character entry screen, touch

character key for a while/ [Character code]

Input a kuten code

: After the fourth digit is entered, the

corresponding character appears.

: After the fourth digit is entered, the entry

mode is switched to the previous entry mode.

■ Convenient functions in character

entry

You can cut, copy or paste the entered characters.

Touch the character entry field for a

while

Select a function to be used

Resetting the FOMA terminal

Reset the FOMA terminal when an error occurs such as that data is not displayed properly or that operation does not work properly.

Remove the back cover

Press the RESET button with a thin

stick etc. for at least 2 seconds

: The FOMA terminal is restart.

Do not reset while using a microSD Card or

saving data.

Before Using the Handset

Page 51

Call/Network Services

Making/Receiving a call . . . . . . . . . . . . . . . . . . 50

Redials/Incoming call history . . . . . . . . . . . . . . 52

Phonebook . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Network services . . . . . . . . . . . . . . . . . . . . . . . 53

Page 52

Making/Receiving a call

Making a call

In the application screen, [Phone]

Enter a phone number

: Always dial the area code, even when the

number is in the same area.

: You can set to notify/not to notify the other

party of your phone number for each call by adding “186”/“184” to the head of the phone number.

[Call]

: To adjust the in-call volume: x/y

[Disconnect] to end the call

Note the following when using hands-free.

･ Speak approximately 20 to 40 cm away from

the mouthpiece. When the surroundings are noisy, the sound may break up and the call may not be satisfactory.

･ When calling outdoors, in a location where

surroundings are noisy and where the sound echoes loudly, use the earphone.

･ If the sound breaks up during a hands-free

call, lower the in-call volume.

Emergency call

Emergency calls Phone number

Emergency call to police 110

Emergency call to fire station/medical assistance

Emergency call at sea 118

This FOMA terminal supports “Location

notification of emergency call”. When dialing an emergency number such as 110, 119, and 118, the information of your location (location information) is automatically notified to the agency that receive the emergency call (e.g. the police station). Depending on your location and the reception status of the signal, the agency that received the emergency call may not be able to confirm the exact location. If you are not sending your caller ID by calling with “184” added or other means, your location information and phone number are not notified. However, if the agency that received the emergency call considers your location information and phone number necessary for important purposes, such as life saving, the agency can retrieve them regardless of your settings. In addition, the area/timing to introduce “Location notification of emergency call” depends on the state of preparation in each agency that receives emergency calls.

119

Call/Network Services

Page 53

When calling 110, 119, and 118 from your

FOMA terminal, the police or fire stations may return your call for verification purposes. State that you are calling from a mobile phone, and give your phone number and exact location. Remain stationary to ensure that you are not disconnected while making an emergency call, and keep handset turned on to receive calls for approximately 10 minutes afterwards.

Depending on the region, calls to the police or

fire station may not be connected.

Making an international call (WORLD CALL)

WORLD CALL is an international calling service available from DOCOMO mobile phones. WORLD CALL is registered when FOMA services are registered (excluding users who did not apply for WORLD CALL).

[Calling Method] 010/Country code/Area code (city code)/Other party’s phone number/[Call]

Alternatively, call with 009130/010/Country

code/Area code (city code)/Other party’s phone number/[Call].

Or, “+” (touch “0” for a while) /Country code/

Area code (city code)/Other party’s phone number/[Call].

For area codes (city codes) that begin with “0”,

omit the “0” when entering (Include the “0” when making a call to some countries or regions such as Italy).

Call to about 240 countries and regions

worldwide.

WORLD CALL charges are billed with the

monthly mobile phone charges.

Commission and monthly usage fees are free. Contact “General Inquiries” on the back of this

manual for WORLD CALL.

To make an international call through a company

other than DOCOMO, contact the representative companies directly for instructions.

This service is not available for some payment

plans.

Receiving a call

When a call is received, the ring

tone sounds and the incoming lamp flashes

Keep touching [2] and slide to the

right

: To place a call on hold: Keep touching [4]

and slide to the left

[Disconnect] to end the call

Call/Network Services

Page 54

Redials/Incoming call

Redials list screen Incoming calls history

list screen

history

The FOMA terminal keeps a record of the 20 most recent phone numbers to which calls were made.

When “186” or “184” is added to a phone

number, the call is recorded as a separate redial.

In the application screen, [Phone]/

[Redial]/[Incoming History]

1 Outgoing call icon

Touch to make a call.

2 The other party’s name/phone number 3 Outgoing and incoming call status icon

Outgoing voice calls

F(red)

Calls that were answered

(green)

Calls that were not answered within 3 seconds ring time

Incoming calls that were

rejected

Calls that were not answered, calls that were forwarded or

calls with a recorded message left

4 Image

Appears when the other party’s image is

added to phonebook.

5 Called/Received date and time 6 Incoming call ring time

Select a history

Phonebook

Adding entries to phonebook

In the application screen, [Address

Book]/z/[Add New Item]

: When multiple accounts are set, select the

account to register.

Set each item/[Save]/[Yes]

Image: Save an image to display when

making and receiving a call or confirming the phonebook.

Family name, Given name: Enter a name.

You can edit a reading.

Phone number: Save phone numbers. Mail: Save mail addresses. Chat: Save chat addresses. Group setting: Save a group. Other: Save other information. Information

which can be saved differs depending on the account type.

Call/Network Services

Page 55

Checking phonebook

You can retrieve phone numbers from the phonebook to make calls and send mail.

In the application screen, [Address

Book]

1 Account

A retrieved phonebook account is

displayed.

2 Tab

The tabs of Japanese syllabary row,

alphanumeric characters and symbols are displayed for the search by reading and the tabs of the saved group names for the search by group.

3 Image

Touch image to display icons of available

applications depending on registration information. Select an icon to activate a compatible application.

4 Icon for switching accounts

Specify the phonebook account to

retrieve.

5 Icon for sorting

Switch the methods of retrieving

phonebook (search by reading/search by group).

6 Icon for searching

Enter characters one by one to display

the closest entries each time.

Select a name

Network services

Available network services

You can use the following network services on

the FOMA terminal.

Service name

Voice Mail Service

Call Waiting Service

Call Forwarding Service

Nuisance Call Blocking Service

Caller ID Notification Service

Public mode (Power off)

“Deactivate” does not mean that the Voice Mail

Service, Call Forwarding Service or other subscriptions are canceled.

Network services are not available outside the

service area or in a place with no signal.

Subscription

Necessary Fees apply

Necessary Free

necessary

Not

Monthly fee

Free

Call/Network Services

Page 56

This manual explains the outline of each network

service based on the operation using the FOMA terminal menu. Refer to “Mobile Phone User’s Guide [Network Services]” for details.

For subscription and inquiries, contact “General

Inquiries” on the back of this manual.

Voice Mail Service

Voice Mail Service is a service for answering incoming voice calls with a reply message and recording callers’ messages when the handset is outside the service area or turned off or when you cannot answer calls. This FOMA terminal does not support

videophone call. However, messages are stored if videophone call of Voice Mail Service is enabled. Make a voice call to “1412” to disable it.

To prioritize Voice Mail Service when Answering

Memo (nP. 61) is also set, set the ringing time for Voice Mail Service shorter than the answering duration for Answering Memo.

If a voice call is not answered when Voice Mail

Service is set to “Activate”, the call is saved as “Missed Call” in “Incoming History” and the notification icon [+] appears.

Basic flow

STEP 1 Activate Voice Mail Service. STEP 2 Voice call is received. STEP 3 Call is connected to Voice Mail Service

center if not answered.

STEP 4 Caller records a message.

To record a message immediately

without hearing a reply message when you are in a hurry, press “#” when a

STEP 5 Play message.

reply message is played.

Call/Network Services

In the home screen, z/

[Settings]/[Call settings]/ [NWService]/[Voice mail service]

Select the service

Activate: Start Voice Mail Service. Ring time: Set time to connect to Voice Mail

Service.

Deactivate: Stop Voice Mail Service. Check setting: Check current settings. Play messages: Play new message. Setting: Set Voice Mail Service. Check messages: Check new message. Notification setting: Set to notify when a

message is stored.

Missed call notification: If a call is received

while the handset is outside the service area, in Offline mode or turned off, SMS notifies the missed calls received after the handset is turned on again or returns to the service area.

You can record up to 20 messages respectively

for calls with approximately 3 minutes of recording time per message. Messages are saved for up to approximately 72 hours.

When Call Forwarding Service is set to

“Activate”, Voice Mail Service is stopped automatically.

Page 57

Call Waiting Service

Call Waiting Service is a service for placing the current call on hold and answering a new incoming call when the handset beeps during a call to notify you of another call. In addition, place the current call on hold and make a new call. When receiving another call during a call, a

beeping is heard twice and stopped but calling is continued.

In the home screen, z/

[Settings]/[Call settings]/ [NWService]/[Call waiting]

Select the service

Activate: Start Call Waiting Service. Deactivate: Stop Call Waiting Service. Check setting: Check current settings.

Charges are incurred by a caller even when the

call is on hold.

Placing the current voice call on hold and

making a voice call to another party are possible even when Call Waiting Service is deactivated.

Call Forwarding Service

Call Forwarding Service is a service for forwarding voice calls when the handset is outside the service area or turned off or when calls are not answered within set ringing time. To prioritize Call Forwarding Service when

Answering Memo (nP. 61) is also set, set the ringing time for Call Forwarding Service shorter than the answering duration for Answering Memo.

If a voice call is not answered when Call

Forwarding Service is set to “Activate”, the call is saved as “Missed Call” in “Incoming History” and the notification icon [+] appears.

Some payment plans are not available.

Basic flow

STEP 1 Register forwarding destination. STEP 2 Activate Call Forwarding Service. STEP 3 Voice call is received. STEP 4 Call is automatically forwarded to the

registered destination if not answered.

Call Forwarding Service fees

Caller

Charged to caller.

Call Forwarding Service

subscriber

Charged to Call Forwarding

Forwarding destination

Service subscriber.

Call/Network Services

Page 58

In the home screen, z/

[Settings]/[Call settings]/ [NWService]/[Call Forwarding]

Select the service

Activate: Start or set Call Forwarding

Service.

Deactivate: Stop Call Forwarding Service. Register number: Change phone number to

forward to.

Forwarding number busy: Set whether to

connect to Voice Mail Service center when the forwarding destination is busy.

Check setting: Check current settings.

When Voice Mail Service is set to “Activate”,

Call Forwarding Service is stopped automatically.

■ Setting Call Forwarding guidance

In the application screen, [Phone]/

enter “1429”/[Call]

: Set according to the voice guidance.

Nuisance Call Blocking Service

You can register phone numbers for “nuisance calls” such as prank calls. When numbers are registered for the Nuisance Call Blocking Service, calls are automatically rejected and a guidance answers them. A ring tone does not sound when calls are

received from registered numbers. In addition, the calls are not saved in the incoming call history.

You can reject callers with no caller ID. International calls may not be rejected.

In the home screen, z/

[Settings]/[Call settings]/ [NWService]/[Nuisance call blocking service]

Select the service

Register nuisance caller: Register the last

caller.

Register selected No.: Register specified

caller.

Delete all entries: Delete all registered

numbers.

Delete last entry: Delete the last registered

number.

Check the number of entries: Check the

number of registered entries.

Call/Network Services

Page 59

Caller ID Notification Service Additional service

You can display your number (caller ID) on the other party’s phone (display) when you make a call. Caller ID is important personal information. Be

very careful about your caller ID setting.

The caller ID notification function is available

only on compatible phone devices.

If you hear a message asking you to notify caller

ID, enable the caller ID notification function or add “186” and call again.

In the home screen, z/

[Settings]/[Call settings]/ [NWService]/[Caller ID notification]

Select the service

Check setting: Check current settings. Setting: Activate/Deactivate Caller ID

Notification Service.

Save and use new DOCOMO network services when they are added. You can save command of new services to the

FOMA terminal. When there is a command, it is saved as a “USSD” to the FOMA terminal.

In the home screen, z/

[Settings]/[Call settings]/ [NWService]/[Additional service]

Select the service

USSD: Register additional services.

･ You can register up to ten new network

services.

Reply message: Register reply message.

･ You can register up to ten reply messages.

Call/Network Services

Page 60

Public mode (Power off)

Public mode (Power off) is an automatic answering service used to ensure the manner in public places. Set Public mode (Power off) to play a message for the caller stating that the power is off and you are unable to speak (in a hospital, on the airplane, near the priority seats on the train, etc.), and the call is disconnected. Voice Mail Service* and Call Forwarding

Service* are activated in priority to Public mode (Power off). * For voice calls whose ringing time is other

than 0 seconds, the service is activated after the Public mode (Power off) guidance.

For calls from callers rejected by Nuisance Call

Blocking Service, Public mode (Power off) is not activated.

In the application screen, [Phone]

Enter “b25251”/[Call]

: Public mode (Power off) is set (Nothing

changes in the home screen).

: When a call is received while Public mode

(Power off) is set and the handset is turned off, a message stating that you are currently in a place that does not allow the use of mobile phone is played.

Disabling Public mode (Power off)

: In the application screen, [Phone]/enter

“b25250”/[Call] ･ Public mode (Power off) is disabled.

Checking Public mode (Power off) setting

: In the application screen, [Phone]/enter

“b25259”/[Call]

･ Check the current setting.

■ When Public mode (Power off) is set

Public mode (Power off) remains set until disabled. The setting is not canceled just by turning on the power. Public mode (Power off) message is played when the handset is outside the service area or in a place with no signal. When a call is received, a message stating that you are in a place that does not allow the use of mobile phone is played and the call is disconnected.

Call/Network Services

Page 61

Various Settings

Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Energy saving setting . . . . . . . . . . . . . . . . . . . . 60

Wireless & networks . . . . . . . . . . . . . . . . . . . . . 61

Call settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Sound & display . . . . . . . . . . . . . . . . . . . . . . . . 62

USB connection . . . . . . . . . . . . . . . . . . . . . . . . 63

Location & security . . . . . . . . . . . . . . . . . . . . . . 64

Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Accounts & synchronization . . . . . . . . . . . . . . . 67

Privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

microSD & phone storage . . . . . . . . . . . . . . . . 68

Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Language & keyboard . . . . . . . . . . . . . . . . . . . 68

Accessibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Text-to-speech . . . . . . . . . . . . . . . . . . . . . . . . . 69

Date & time. . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

About phone . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Page 62

Profile Energy saving setting

You can check the phone number of the inserted UIM and register a name or mail address.

In the home screen, z/

[Settings]/[Profile] z/[Edit]/set each item/

z/[Save]/[Yes]

: For details on each item which can be set

nP. 52

Set to conserve the battery power.

In the home screen, z/

[Settings]/[Energy saving setting]

Select an item

Anyway energy saving: Set all the items

displayed in Energy saving setting to conserve the battery power.

Wi-Fi, Bluetooth: For details nP. 61 Pulse notification light, Audible touch tones,

Audible selection, microSD notifications, Orientation, Brightness, Screen light on time: For details nP. 62

Use GPS satellites: For details nP. 64 Background data: For details nP. 67

Various Settings

Page 63

Wireless & networks

Set communication such as Wi-Fi and Bluetooth function.

In the home screen, z/

[Settings]/[Wireless & networks]

Select an item

Offline mode: Restrict the use of all functions

using communication such as call/mail function.

Wi-Fi: Enable Wi-Fi function. Wi-Fi settings: For details nP. 34 DLNA server settings: For details nP. 100 Bluetooth: Activate Bluetooth function. Bluetooth settings: For details nP. 103 VPN settings: Set and manage VPN. Mobile networks: For details nP. 109

[Offline mode]

When the SIM card lock setting is enabled, you

cannot call to the emergency number (110, 119 or 118). When the SIM card lock setting is disabled, you can call to the emergency number (110, 119 or 118) in Offline mode. If you call to the emergency number, Offline mode is disabled and the call is made.

Call settings

Set call such as voice mail, reject calls, etc.

In the home screen, z/

[Settings]/[Call settings]

Select an item

Any-key answer: Set an action when you

press a key on receiving a call.

Call/Message: Play or set Call/Answer

Memo. If you set Answering Memo, the FOMA terminal answers a call and records the caller’s message when you cannot answer.

Auto answer: Set to answer a call

automatically when an earphone is connected.

Call blocking: Set Call blocking. NWService: For details nP. 53

■ Key operation for receiving a call with

Any-key answer setting

Answer

To answer: x, y, G To open the menu: z To display quick search box: }

Quick silent

To stop ring tone and vibration: |, {, H,

x, y, }, G

To stop ring tone and vibration and open the

menu: z

OFF

To stop ring tone and vibration: x, y To open the menu: z To display quick search box: }

Various Settings

Page 64

Sound & display

Set ring tone, operation sound, screen display, etc.

In the home screen, z/

[Settings]/[Sound & display]

Select an item

Manner mode: Set to avoid disturbing others

when in public. ･ Alternatively, in the home screen, H (for

at least 1 second)/[Manner mode].

Incoming voice call: Set an action for

receiving. ･ You can also change the volume of

incoming voice call by pressing x/y. You can also set Manner mode.

Reminder settings: Set an action for

receiving notification.

Media volume: Set the volume of media play

sound.

Phone vibe: Set whether to enable the

vibrator for receiving a call.

Pulse notification light: Set whether to flash a

lamp for receiving a notification.

Audible touch tones: Set whether to enable

dial sound.

Audible selection: Set whether to enable

operation sound for selecting items.

Haptic feedback: Set whether to enable the

vibrator for specific key operation.

microSD notifications: Set whether to enable

operation sound for performing Unmount microSD or microSD Card being broken.

Earphone type: Set the type of connected

earphone.

Wallpaper: Set an image of wall screen.

Incoming call screen: Set the screen for

receiving.

Orientation: Set whether to automatically

switch the vertical/ horizontal view according to the direction of the FOMA terminal.

Animation: Express screen switch with

animation.

Brightness: Set the brightness of backlight. Screen light on time: Set the light duration of

backlight.

Veil view: Prevent others from seeing

display.

Text font: Set the text font. 3D parallax: Set the 3D parallax.

Note that if the vibrator is set to be enabled and

the FOMA terminal is left on a table, it may fall due to vibration.

[Manner mode]

The following is not silenced even while Manner

mode is set.

Shutter sound of camera Record start/end sound of camera Start/end sound of voice recorder

Various Settings

Page 65

The following manner mode can be set.

Standard manner mode: The ring tone and

operation sound are silenced, and the vibrator is activated when receiving a call or others. Answering Memo is enabled and operated according to its setting.

Drive manner mode: The ring tone and

operation sound are silenced, and the vibrator is not activated even when receiving a call or others. Answering Memo is enabled and operated with the Answering message setting of [DRIVE].

Silent manner mode: The ring tone and

operation sound are silenced, and the vibrator is not activated even when receiving a call or others. Answering Memo is enabled and operated according to its setting.

[Pulse notification light]

If no operations are performed for

approximately 24 hours after notification lamp starts flashing, notification lamp will be turned off.

[Orientation]

Vertical/Horizontal view is not switched if the

FOMA terminal is turned in the place parallel to the ground.

[Brightness], [Screen light on time]

Note that increasing the brightness level or the

light duration shortens the continuous stand-by time.

[Veil view]

The effect of preventing others from seeing

differs depending on the selected patterns.

The intensity is more effective to prevent others

from seeing the display in order of [Dark], [Medium], and [Light].

When a 3D image is displayed, VeilView is

disabled.

VeilView is disabled if the power is turned off.

[Text font]

Font may not appear correctly when activating

an application downloaded from Android Market, etc. depending on the selected font.

USB connection

Change the setting in connecting the FOMA terminal to PC using the microUSB cable for PC (sample).

In the home screen, z/

[Settings]/[USB connection]

Select an item

USB battery charge: Charge the FOMA

terminal while it is connected to a PC via the microUSB cable for PC.

USB connection mode: Change the mode

set when connecting the FOMA terminal to a PC. ･ Connect the FOMA terminal to a PC via the

microUSB cable for PC in advance.

[USB battery charge]

USB battery charge setting is reflected when a

USB is connected next time or the USB connection mode is changed.

Various Settings

Page 66

[USB connection mode]

The following modes can be set.

Card reader mode: Mode for using microSD

Card inserted to the FOMA terminal as an external memory for a PC.

Fast transfer mode: Mode for upgrading OS

version.

MTP mode: Mode for transferring music/

video/still picture data to microSD Card using Windows Media

While transferring data, Offline mode may be

enabled.

Player 11/12.

Location & security

Set the security lock or the way to retrieve information of the present location.

In the home screen, z/

[Settings]/[Location & security]

Select an item

Use wireless networks: Position location

information using wireless network.

Use GPS satellites: Position location

information with higher accuracy.

Lock Setting: Set the various locks. Unlock method: Change the unlock method.

Lock No. or Finger list can be used.

Change unlock pattern: Change the security

code or the pattern set for unlock method.

Use visible pattern: Display track for entering

finger list pattern with line.

Use tactile feedback: Activate vibration on

entering finger list pattern.

Set up SIM/RUIM card lock: Set for the PIN

code.

Visible passwords: When you enter the PIN

code etc., you can display the entered characters before displaying [・].

Use secure credentials: Allow to access

secure certificates and other credentials. ･ Set the credential storage password in

advance.

Install from microSD: Install encrypted

certificates from microSD.

Set password: Set the credential storage

password.

Clear storage: Delete all credentials and

reset the credential storage password.

It is necessary to enable location information

services ([Use wireless networks] or [Use GPS satellites]) to measure the present location.

[Use GPS satellites]

Power consumption of the FOMA terminal

increases.

[Lock Setting]

If you failed to enter finger list pattern five times

when disabling Screen lock, [Forget?] appears. Disable the lock by signing in with your Google account and enter new finger list pattern.

You can call to the emergency number (110,

119 or 118) even when you set Restrict calls.

To use a function while it is restricted, enter the

Lock No. to temporarily disable the restriction.

[Set up SIM/RUIM card lock]

In Japan, you cannot call to the emergency

number (110, 119 or 118) from the PIN code entry screen and PUK (PIN Unlock Key) entry screen, with a UIM locked.

The setting is saved in the UIM card.

Various Settings

Page 67

Security codes used on the FOMA terminal

Some functions for convenient use of the FOMA terminal require security codes. In addition to the Lock No. used for various handset operations, use security codes such as the network security code when using network services. Use security codes with various functions to fully utilize the FOMA terminal. Entered Lock No. (security code for each

function) and PIN code are marked with [・].

Precautions for various security codes

Do not use easily estimated numbers for

security codes to be set such as “birthday”, “part of a phone number”, “address or room number”, “1111” or “1234”. Keep a separate memo of security codes.

Keep security codes private. If the security

codes are found and improperly used by others, DOCOMO shall not be liable for any loss of the users.

If you forget your security codes, you are

required to bring your identification (a driver’s license, etc.), your FOMA terminal and your UIM to a docomo Shop. For details, contact “General Inquiries” on the back of this manual.

PUK (PIN Unlock Key) is described in the

agreement form (customer copy) you received at the time of subscription at a docomo Shop. If you made a subscription outside a docomo Shop, bring your identification (a driver’s license etc.) and your UIM to a docomo Shop or contact “General Inquiries” on the back of this manual.

■ Lock No. (for various functions)

Lock No. is set to [0000] by default but you can change the number (nP. 64). If you enter the wrong Lock No. five times

continuously, you cannot enter it for 30 seconds.

■ Network security code

Network security code is a four-digit code required for confirming the subscriber’s identity when an order is received at a docomo Shop or docomo Information center or used for accessing various network services. You set arbitrary code at the time of subscription but you can change the code. For those with “docomo ID/password” of the general support site “My docomo” designed for PC (in Japanese only), the registration procedure for a new network security code is available from PC. Refer to the inside back cover of this manual for

details on “My docomo”.

■ PIN1 code/PIN2 code

A UIM has two security codes: PIN1 code and PIN2 code. These security codes are set to [0000] by default but you can change the code (nP. 64). The PIN1 code is a four- to eight-digit security code that is entered when a UIM is inserted or when the FOMA terminal is turned on to prevent unauthorized use by a third party. Making/ Receiving a call and the terminal operation are enabled by entering PIN1 code. ※This FOMA terminal does not support PIN2

code.

Use the previously set PIN1/PIN2 code when

inserting a UIM that has been used in another FOMA terminal. It is [0000] if the setting has not been changed.

Various Settings

Page 68

If you enter the wrong PIN1/PIN2 code three

times continuously, it is locked. In this case, unlock with “PUK” (PIN Unlock Key).

■ PUK (PIN Unlock Key)

PUK (PIN Unlock Key) is an eight-digit number used to disable the PIN code lock. You cannot change the code. If you enter the wrong code ten times

continuously, the UIM is completely locked. In this case, contact a docomo Shop.

Disabling PIN lock

In the PIN locking screen,

[Emergency call] Enter “＊＊05＊”/enter PUK (PIN

Unlock Key)/enter “＊”/enter the new PIN code/enter “＊”/enter

the new PIN code again/enter “#”

: Enter “＊＊05＊88888888＊7777＊7777#”

to change PIN code to “7777” when PUK (PIN Unlock Key) is “88888888”.

Applications

Manage applications.

In the home screen, z/

[Settings]/[Applications]

Select an item

Unknown sources: Allow installation of

application received via mail or site other than Android Market.

File transfer mail software: Set a mail

software to be activated by attaching to mail from another application.

Manage applications: Check application

names, their versions, and the memory usage.

Running services: Display and control the

running services.

Development: Use application development

functions.

[Unknown sources]

Applications you download from the sites may

be of unknown origin. To protect your FOMA terminal and personal data, download only applications from trusted sources such as Android Market.

[Development]

Refer to http://developer.android.com/ for

details on development function.

Various Settings

Page 69

Accounts & synchronization

You can synchronize data between the FOMA terminal and network services. You can access personal information stored in network services from the FOMA terminal and PC, and you can use and update data by synchronizing them.

In the home screen, z/

[Settings]/[Accounts & sync]

Select an item

Background data: Allow all applications to

automatically perform data communication.

Auto-sync: Allow all applications to

automatically perform data synchronization.

: Accounts to be synchronized are displayed

as items in “Manage accounts”.

: For details on adding an account nP. 36

synchronize phonebook of your FOMA terminal with contacts on the network services even if you synchronize with other than Google account.

Privacy

In the home screen, z/

[Settings]/[Privacy]

Select an item

Use My Location: Use the information of the

present location in search results or services of Google.

Reset all: Delete all of the data in the FOMA

terminal.

Various Settings

Page 70

microSD & phone storage

In the home screen, z/

[Settings]/[microSD & phone storage]

Select an item

Total space: Check the microSD Card space. Available space: Check the available space

in the microSD Card.

microSD backup: Back up the data from the

FOMA terminal to the microSD Card or read the backup data from the microSD Card to the FOMA terminal.

Unmount microSD: Disable recognition of the

microSD Card.

Format microSD: Format the microSD Card.

･ Unmount the microSD Card in advance.

Available space: Check the available space

in the FOMA terminal.

[microSD backup]

When the available memory space of the

FOMA terminal is less than 11 MB, microSD backup is unavailable.

[Format microSD]

Note that all the data on the microSD Card will

be deleted when formatted.

Search

Set the Google search.

In the home screen, z/

[Settings]/[Search]

Select an item

Google search settings: Set whether to

display search options when characters are entered.

Searchable items: Select data types in the

FOMA terminal to search for.

Clear search shortcuts: Delete the shortcuts

for recently selected search results in the quick search box.

Language & keyboard

Set the language displayed in the screen or character entry.

In the home screen, z/

[Settings]/[Language & keyboard]

Select an item

Select language: Select Japanese/English. Android keyboard: Set the Android keyboard. iWnn IME - SH edition: Set iWnn IME - SH

edition.

User dictionary: Register any words in the

dictionary and display them as conversion candidates when you enter the characters with the Android keyboard.

Various Settings

Page 71

Accessibility

Accessibility option which responds to user’s operation with sound and vibration is available.

By default, accessibility option is not registered.

Settings will be available by downloading accessibility options such as “SoundBack”, “KickBack” and “TalkBack” from Android Market.

In the home screen, z/

[Settings]/[Accessibility]

Select an item

Text-to-speech

Set the voice reading out text.

Text-to-speech is available only when the screen

of the FOMA terminal is set to the English display (nP. 68).

In the home screen, z/

[Settings]/[Text-to-speech]

Select an item

Listen to an example: Play the sample. Install voice data: Install the data necessary

for Text-to-speech.

Always use my settings: Overwrite the

application settings with the contents set in “Speech rate” and “Language”.

Speech rate: Select the speed to read out

the text.

Language: Set the language to read out the

text.

Date & time

In the home screen, z/

[Settings]/[Date & time]

Select an item

Automatic: Set whether to adjust the date

and time automatically.

Set date: Set the date manually. Select time zone: Set the time zone

manually.

Set time: Set the time manually. Use 24-hour format: Switch 12-hour format/

24-hour format.

Select date format: Set the date format to

display.

When [Automatic] is enabled

If the FOMA terminal does not adjust the time

for a while after the power is turned on, turn off the power and restart it.

Time may not be adjusted depending on the

signal status.

Time may be off by a few seconds.

Various Settings

Page 72

About phone

Check the information about phone.

In the home screen, z/

[Settings]/[About phone]

Select an item

Major Update: Upgrade OS version of the

FOMA terminal by connecting the FOMA terminal to your PC. ･ For details on upgrade nP. 106

Software Update: For details nP. 119 Adjust sensitivity of sensor: Adjust accuracy

of motion sensor and geomagnetic sensor.

Status: You can check the battery level,

network in use, etc.

Battery use: You can check the battery

usage per application.

Legal information: You can check copyright

notice, terms of service, etc.

Model number: You can check the model

number.

Firmware version: You can check the

firmware version.

Baseband version: You can check the

baseband version.

Kernel version: You can check the kernel

version.

Build number: You can check the build

number.

[Adjust sensitivity of sensor]

Adjustment may be failed depending on

surroundings or other simultaneously running applications. Change the place where you make adjustment or end running applications.

Various Settings

Page 73

Mail/Browser

Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

sp-mode mail . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Gmail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

SMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Page 74

Mail

Set the account in advance (nP. 35).

In the application screen, [Email]

: The Inbox screen appears when an account

is registered.

: The mail main screen appears when multiple

accounts are registered.

■ Mail screen layout

Green circle shows the number of unread mails. Gray circle shows the number of applicable

mails.

Mail main screen

1 Combined Inbox

Display received mails of all accounts.

2 Starred

Display starred mails of all accounts.

3 Drafts

Display drafts of all accounts.

4 Outbox

Display unsent mails of all accounts.

5 Accounts

Display the Inbox screen of selected account.

6 Priority account mark

Displayed for an account to be preferentially

used when composing a mail.

7 Folder mark

Display the mailbox screen of selected

account.

Mailbox screen

To display the mail main screen: z/

[Accounts]

1 Inbox

Display received mail.

2 Drafts

Display draft.

3 Outbox

Display unsent mail.

4 Sent

Display sent mail.

5 Trash

Deleted mails are stored.

Mail/Browser

Page 75

Inbox screen

Layout for the mail list screen of Outbox is same

as that of the Inbox screen.

To display the mail main screen: z/

[Accounts]

To display the mailbox screen: z/[Folders]

1 Received mail

Display the detailed screen of received mail.

You can reply or delete.

Unread mail is displayed in gray.

2 Check box

Operation menu appears on the bottom of the

screen if you check the box. You can check multiple boxes and operate checked items simultaneously.

3 Clip mark

Displayed for mail with attachment file.

4 Star mark

If you star a mail, you can display only starred

mails as a list from the mail main screen.

Composing and sending mail

In the mail screen, z/

[Compose]

Enter a destination, a subject, and a

message/[Send]

: To attach a file: z/[Add attachment]/

select a file

Some receiving models may not be able to

receive the subject completely.

Mail sent from a Gmail account are treated as

one from a PC. When receiving models set PC-mail rejection, mails cannot be sent.

Mail that could not be sent by some reason is

saved as unsent mail.

Text for recipient may not appear correctly

depending on signal status.

Attaching file

You can attach up to 5 MB by each file. There

are no limits for number of attaching data.

Depending on the receiving side terminal, files

may not be received nor correctly displayed/ played. Also, the quality of videos may deteriorate or videos may be converted to continuous still pictures.

sp-mode mail

You can send and receive mail using i-mode mail address (@docomo.ne.jp). Pictograms and Deco-mail are available. Automatic reception is also supported.

In the application screen, [spモード

メール] (sp-mode mail)

Mail/Browser

Page 76

Gmail

Gmail is a mail service provided by Google.

Refer to Gmail website for details on Gmail.

In the application screen, [Gmail]

SMS

You can send and receive SMS using phone numbers.

You can also exchange messages with users of

non-DOCOMO overseas telecommunications carriers. Refer to “Mobile Phone User’s Guide [International Services]” or the DOCOMO “International Services website” for information on available countries and overseas telecommunications carriers.

In the application screen,

[Messaging]

: SMS list screen appears.

[New message]/enter a

destination and a message/[Send]

For destinations of non-DOCOMO overseas

telecommunications carriers, enter “+”, the country code, and the recipient’s mobile phone number. If the phone number begins with “0”, omit the “0”. Alternatively, enter “010”, the country code and the phone number. Add “010” to reply to SMS received from abroad.

Single-byte katakana and special symbols in

SMS text may not appear correctly for recipient.

SMS cannot be sent when “186” or “184” is

added.

Mail/Browser

Browser

This FOMA terminal can display sites over packet transmission or wireless LAN connection.

In the application screen, [Browser]

Some sites may not appear properly.

Enabling JavaScript

In the browser screen, z/

[More]/[Settings]/[Enable JavaScript]

Page 77

Multimedia

Shooting with camera . . . . . . . . . . . . . . . . . . . . 76

Gallery (3D) . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Contents Manager . . . . . . . . . . . . . . . . . . . . . . 82

MusicPlayer . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Page 78

Shooting with camera

Before using camera

Fingerprints or oil on the lens may cause the

image to be out of focus. In addition, images may blur and rays of light may appear in images when shot near a strong light source. Wipe the lens with a soft cloth before shooting images.

You cannot shoot when battery level is

insufficient. Images may appear dark and distorted when shot with insufficient battery power even while the handset is charging. Do not shoot images while charging.

Although the cameras are made with

high-precision technology, some pixels or lines look constantly dark or bright. Further, white lines and other noise may appear in images especially when shooting images in dimly lit surroundings.

The quality of images may deteriorate when shot

or saved after the FOMA terminal has been left in a warm location for a long time.

If the camera lens is exposed to direct sunlight

for a long time, the internal color filter may discolor, creating a discoloration of shot images.

Images shot in shooting conditions which include

strong light source such as the sun or a lamp may appear dark and distorted.

Shooting the sun directly may damage the

performance of the CCD.

The FOMA terminal may become warm and the

camera may end after shooting still pictures continuously, shooting long moving pictures or activating the camera for a long time. This is not a malfunction. Use the camera again after a while.

Multimedia

When Focus Settings is switched, sounds may

be heard from the camera lens. This is not a malfunction.

Images are blurred when the FOMA terminal

moves while shooting images. Hold securely to prevent blurring. Use Steady cam function when shooting still pictures.

The color and brightness of the subject in images

shot with the camera may differ from the actual color and brightness.

Make sure that your fingers, hair and handset

strap do not obscure the camera lens when shooting images.

Because a larger image size requires more data,

movement in the image on the FOMA terminal display may appear slow.

Indoor fluorescent lighting may create flickering

or streaky shading on the screen. This flickering or shading may be reduced by changing the lighting conditions, brightness or adjusting the camera brightness and white balance.

Shot still pictures are saved in DCF1.0

(ExifVer.2.2, JPEG) format. ･ “DCF” (Design rule for Camera File system) is

a standard created mainly by JEITA (Japan Electronics and Information Technology Industries Association) for images from digital cameras and other devices to be shared with related devices. However, DCF standard does not guarantee the entire compatibility of all devices.

･ “Exif” is a file format established by JEITA

(Japan Electronics and Information Technology Industries Association) for adding supplementary information to the still picture.

The camera is not available while using 1Seg.

Page 79

Copyrights and rights of portrait

Images and audio recorded with the FOMA terminal are for personal use and may not be used without the consent of the rightful person in accordance with copyright laws. Please note that the use of the likeness or name of other individuals without their consent, defacement or a similar act may infringe on an individual’s rights of portrait. Please be aware of copyrights and rights of portrait when making public images and audio recorded with the handset on the Internet or similar media. The recording of images or audio may be restricted at concerts, performances and exhibits even when recorded for personal use. Do not use this handset to send copyrighted images for uses other than those permitted under copyright laws. If you cause the public any trouble using the FOMA terminal, you may be punished under law or regulations (for example, nuisance prevention ordinance).

Please be considerate of the privacy of individuals around you when shooting and sending pictures using a camera-enabled mobile phones.

■ Performance while using camera

Shooting LED flashes in each camera mode. In each camera mode, if no operations are

performed for approximately 3 minutes, the camera mode automatically ends and the home screen reappears. Unsaved data is saved and the scanned result is deleted.

In each camera mode, Picture Light cannot be on

after lighting on for 3 minutes in total. End each camera mode and reactivate it to put Picture Light on.

The shutter sound volume cannot be changed.

■

Image size and magnification of camera

The following image size and magnification are

available.

Maximum magnification

(zoom step)

Actual size (–)

Approx. 1.3× (3 steps)

Approx. 1.5× (4 steps)

Approx. 1.8× (5 steps)

Approx. 2.1× (6 steps)

Approx. 3.9× (10 steps)

Approx. 5.2× (12 steps)

Approx. 22.2× (18 steps)

Approx. 2.4× (7 steps)

Approx. 3.9× (10 steps)

Approx. 5.2× (12 steps)

Approx. 7.9× (15 steps)

Shoot still picture

Shoot moving picture

Image size

9.5M: 3552×2664

5M: 2592×1944

3M: 2048×1536

FullHD: 1920×1080

2M: 1600×1200

WVGA: 800×480

VGA: 640×480

QVGA: 320×240

HD: 1280×720

WVGA: 800×480

VGA: 640×480

QVGA: 320×240

Multimedia

Page 80

■ Shooting screen layout

Example: Still picture shooting screen

1 Remaining number of pictures which can be

shot

Even after shooting a still picture, remaining

number of pictures which can be shot may not be changed.

2 Thumbnail

Shoot a still picture when Auto-save is set to

[ON]. Thumbnail appears. Touch to display the shot image.

3 Shooting status icon

You can confirm each settings about shooting

by icons. Touch to display the touch menu in the still/moving picture shooting screen.

Example: Displaying the touch menu in the

Display the touch menu by touching the shooting

still picture shooting screen

status icon in the still/moving picture shooting screen. You can change settings.

1 Set value list 2 Current set value 3 Set item list

Camera

Shoot a still picture.

In the application screen, [Camera]

: To adjust the brightness: Quickly slide up/

down

: Zoom: Quickly slide to the left/right : Focus lock: Touch the subject

･ Touch anywhere other than focus frame to

cancel the focus lock.

[!]

: The shutter sounds. : If Auto-save is set to [ON], this operation is

completed.

[Save]

Camera (3D photos)

Shoot a 3D still picture.

In the application screen, [Camera

(3D photos)]

: To adjust the brightness: Quickly slide up/

down

: Zoom: Quickly slide to the left/right : Focus lock: Touch the subject

･ Touch anywhere other than focus frame to

cancel the focus lock.

[!]

: The shutter sounds.

Multimedia

Page 81

Move the FOMA terminal to the

right

: Slowly and horizontally move the FOMA

terminal.

: Shooting is completed when the indicator

reaches the right edge. The shot 3D still picture is automatically saved.

Video Camera

Shoot a moving picture.

In the application screen, [Video

Camera]

: To adjust the brightness: Quickly slide up/

down

: Zoom: Quickly slide to the left/right

[(]

: Shooting starts after the shooting start sound

is heard.

[)] to end shooting

: After the shooting end sound, the moving

picture shooting confirmation menu screen appears.

Select an item

Save: Save a moving picture. Share Video: Post to SNS or video site. Mail: Attach to mail. Play: Play a moving picture. Cancel: Cancel shooting.

The remaining time indicator is an

approximation. Shooting may continue longer than the remaining time indicated before the start of shooting or may automatically stop even when there is remaining time.

Barcode reader

You can use the camera to scan bar codes (JAN/ QR codes), and perform various operations according to the contents of scanned item.

JAN code

JAN code is a type of bar code using vertical

bars of varying width to express numbers.

The following code is read as [4942857119022].

JAN8 and JAN13 can be read.

QR code

QR code is a type of two-dimensional code

expressing data vertically and horizontally.

The following code is read as [株式会社NTTドコ

モ].

In the application screen, [Barcode

reader]

: To adjust the brightness: Quickly slide up/

down

: Focus lock: [AF]

Scan the bar code

: The Barcode reader screen appears and

scanning starts. Display bar code to be scanned in the center of the screen.

Multimedia

Page 82

: Position the camera approximately 10 cm

from the bar code. Keep aligned and do not move the FOMA terminal or code while scanning.

: When scanning is complete, an end tone

sounds and the scan result screen appears.

Split data

: Some QR codes are split into a multiple

codes (up to 16) consisting single data. If split data is scanned, a message appears. Select [Yes] to proceed to the next QR code scanning screen. When the next QR code is displayed in the center of the screen, scanning starts automatically. Repeat until all split data is scanned and the scan results appear.

Use the scan result

Some bar codes cannot be scanned depending

on types or sizes.

Bar codes may not be scanned due to

scratches, dirt, damage, poor print quality, lighting conditions or QR code version.

Business card reader

You can scan information such as name or phone number from a business card (Japanese/English) with the camera and newly save it to the phonebook.

In the application screen, [Business

card reader]

: To adjust the brightness: Quickly slide up/

down

Display a business card in the

center of the screen/[Read]

: The shutter sounds.

Multimedia

: Hold the FOMA terminal securely to fit the

entire business card with the frame displayed on the screen. Make sure that no other objects, especially text-written objects, are displayed on the screen.

: Keep the camera approximately 10 cm away

from the business card.

: For scanning, the direction of the business

card can be either vertical or horizontal on the screen. Do not place the card obliquely.

[Register]

: The shot card images are automatically

saved.

Specify the register range of the

image/[Save]

: The specified range of the image is added to

the phonebook as an image.

Add to the phonebook

: Scanned items are entered in the phonebook

editing screen.

Some business cards cannot be scanned or

recognized properly.

Information reader

You can scan information such as store name, phone number, etc. from a magazine, etc. by using the camera, and newly save it to the phonebook.

In the application screen,

[Information reader]

: To adjust the brightness: Quickly slide up/

down

Display information in the center of

the screen/[Read]

Page 83

: The shutter sounds. : Hold the FOMA terminal securely to fit

necessary information in the screen. However, if the text gets too small, display a phone number or address largely enough to be scanned.

: Keep the camera approximately 10 cm away

from necessary information.

[Register]

: The shot card images are automatically

saved.

Specify the register range of the

image/[Save]

: The specified range of the image is saved to

the phonebook as an image.

Add to the phonebook

: Scanned items are entered in the phonebook

editing screen.

Some information cannot be scanned or

recognized properly depending on the description of magazine, etc.

Text reader

You can scan an article of newspaper, magazines, etc. by using the camera, and compose mail or notepad, etc.

In the application screen, [Text

reader]

: To adjust the brightness: Quickly slide up/

down

Display the text to scan in the

screen/[Shoot]

: The shutter sounds.

Point the cursor to the line to scan

with [#]/[$]/[Read]

: When letters written in vertical direction are

recognized: [%]/[&]

: The line to which the cursor is pointed is

displayed in light blue frame.

[OK]

: To change scanning mode: [Mode]/select a

mode

Use the scan result

Text may not be scanned correctly due to

scratches, dirt, damage, poor print quality, lighting conditions or text size.

Gallery (3D)

Gallery(3D)

Display still pictures or moving pictures.

In the application screen,

[Gallery(3D)]

: [a] superimposed on 3D data appears.

Select data

: If there are multiple players to play the data

and player is not set, a player selection screen appears. Select a player to play the data.

■ Operation while displaying 3D images

To switch to 2D image: [b]/[Operation]

･ Touch a 2D image to display a 3D image

again.

To adjust stereoscopic effect of 3D image: [3D

parallax]/slide the adjustment bar

Multimedia

Page 84

To display/hide operation key: Touch an image

3D conversion

Convert a 2D still picture to a 3D still picture.

In the Gallery (3D) screen, select a

2D still picture/z/[More]/[3D conversion]/[Save]

Category Displayed data

Others Other data

Select data

: If there are multiple players to play the data

and player is not set, a player selection screen appears. Select a player to play the data.

Contents Manager

You can manage the data saved in the microSD Card, classify the data by types and displays it.

In the application screen, [Contents

Manager]

: Select the category on the bottom of the

screen to display the data of selected category.

Category Displayed data

Photo Still pictures shot with the

Movie Moving pictures shot with the

Music Data recorded with the FOMA

TV Videos recorded with the

Doc. Office type data (.doc, .xls, .ppt,

Multimedia

FOMA terminal or downloaded images

FOMA terminal or downloaded videos

terminal, melodies or WMA files

FOMA terminal or recorder link data

.docx, .xlsx, .pptx, .csv), PDF data or Text file

MusicPlayer

In the application screen,

[MusicPlayer]

Select data

: To adjust the volume of play sound: x/y

■ Main touch panel operation in music

playback screen

The following operations are available with

displayed keys.

[9]*/[<] Play previous/next data [:]/[;] Play/Pause [8] Display music list screen [6] Repeat [7] Shuffle

* Return to beginning of the song if the

playback time is 1 second or more.

The following touch operations are available.

To switch display Quickly slide up/down

To change playback position

Touch seek bar

Page 85

Convenient Functions

Using GPS function . . . . . . . . . . . . . . . . . . . . . .84

Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

1Seg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Osaifu-Keitai . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Calendar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Alarm/Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .93

Notepad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94

Voice Recorder . . . . . . . . . . . . . . . . . . . . . . . . .94

Calculator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95

Dictionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Android Market . . . . . . . . . . . . . . . . . . . . . . . . . 96

docomo market. . . . . . . . . . . . . . . . . . . . . . . . . 97

Infrared communication . . . . . . . . . . . . . . . . . . 98

Cooperating with Blu-ray Disc recorder . . . . . 100

Setting DLNA server. . . . . . . . . . . . . . . . . . . . 100

Bluetooth function. . . . . . . . . . . . . . . . . . . . . . 101

PC connection . . . . . . . . . . . . . . . . . . . . . . . . 104

OS version upgrade . . . . . . . . . . . . . . . . . . . . 106

Page 86

Using GPS function

GPS function of the FOMA terminal can perform

positioning present location in a state that GPS radio wave can be received. In addition, enable location information services to measure the　 present location (nP. 64).

Note that DOCOMO shall not be liable for the

pure economic loss if you cannot confirm the positioning (communication) result with the FOMA terminal failure, malfunction or external factors such as power failure (including battery exhaustion).

You cannot use the FOMA terminal as navigation

system for professional use of aircrafts, vehicles, person, etc. Therefore, note that DOCOMO shall not be liable for the loss caused by the navigation system to use location information.

You cannot use the FOMA terminal as surveying

GPS of high accuracy. Therefore, note that DOCOMO shall not be liable for the loss caused by the error of location information.

GPS is the service in charge of Department of

Defense of USA. Therefore, GPS radio wave condition may be controlled (accuracy degradation, radio wave abort, etc.) for the US national security reason.

Note that GPS is using the radio wave from

satellites, and following conditions may cause the radio wave abort or difficulty to receive.

In or under buildings In basement, tunnel, ground or water In bags or boxes In density area with buildings or residence In or under densely trees Near high-tension line

Inside cars or trains In bad weather with heavy rain/snow When people or objects are blocking mobile

phones

When hands are covering camera, 1Seg

antenna, earpiece or proximity sensor In these cases, the error of retrieved location information may be 300 m or more.

When using a map and GPS function overseas,

the displayed map based on the acquired location information (latitude and longitude information) may not be accurate because of the legal system in each country and the area.

Packet transmission charges may be incurred

since assist data such as satellite information is automatically retrieved when you position present location.

Packet transmission charges are incurred when

you display a map based on the location information.

Convenient Functions

Page 87

Compass

Display a map or compass to check your location or the direction that the FOMA terminal is headed to.

There are two modes for checking: a compass

mode which shows the direction of the FOMA terminal with a compass and a map mode which shows the direction of the FOMA terminal with an azimuth icon on map.

To display maps, enable data connection or

connect to Wi-Fi.

Enable location information services in advance

to measure the present location (nP. 64).

In the application screen,

[Compass]

■ Compass screen layout

Compass mode

1 Azimuth 2 Compass

Needle rotates in accordance with the

direction of the FOMA terminal.

In accordance with the tilt of the FOMA

terminal, flat display and birds-eye display are switched.

3 Map window

The way of reading the map is the same as in

the map mode screen.

Touch the map to switch to the map mode.

4 Angle

Display the angle from North to the front of the

FOMA terminal.

Map mode

1 Map 2 Present location call-out

Display the address or street name of the

point on which a human icon is displayed.

3 Compass window

The way of reading the compass is the same

as in the compass mode screen.

Touch the compass to switch to the compass

mode.

4 Human icon

It is displayed on the present location.

5 Azimuth icon

Display the direction of the FOMA terminal on

the map.

Convenient Functions

Page 88

1Seg

1Seg is a terrestrial digital TV broadcasting service for mobile devices and can receive data broadcasting with image and voice. In addition, you can acquire more detailed information of a program or enjoy participating in a quiz program or teleshopping. For details on the “1Seg” service, see the website below. The Association for Promotion of Digital Broadcasting http://www.dpa.or.jp/english/

■ Using 1Seg

1Seg is a service provided by TV broadcasters (broadcast stations) etc. Transmission charges are not incurred for receiving image, voice and sound. Contact NHK for details on viewing fees of NHK. Available information in the area of the data broadcasting is “data broadcasting” information and “data broadcasting site” information. “Data broadcasting” information is carried in a broadcast wave, together with image, voice, and sound. “Data broadcasting site” information is used to access sites provided by the TV broadcaster (broadcast station). Packet transmission charges are incurred when accessing a site such as a “data broadcasting site” or others. Some sites require information charges to use.

■ About broadcast wave

1Seg is one of the broadcasting services, and the receiving signal (broadcast wave) differs from that of FOMA service. Therefore, it cannot be received at the place where the broadcast wave does not reach or while the broadcasting is out of service, regardless of whether the FOMA terminal is outside or inside the FOMA service area. Also, in the following places, the signal status may become weak or the signal may not be received even if the FOMA terminal is inside the area of a terrestrial digital TV broadcasting service. Place that is far from the tower which sends the

broadcasting wave

Place where the signal is interrupted due to the

landscape or buildings such as mountain areas or behind a building

Place where the signal is weak or does not reach

to, such as a tunnel, basement or a place in the rear of a building

To receive in better conditions, fully pull out the 1Seg antenna. In addition, change the direction of antenna, hold the FOMA terminal apart from or close to the body or move to another place, so that the reception status may become better.

■ About 1Seg antenna

When you change the direction of the 1Seg

antenna, do not apply excessive force to do.

When you fold the 1Seg antenna, do not hold its

tip and fold it forcibly or it can be damaged. Hold the bottom of the antenna, put it down straight, and store it completely to the tip.

Convenient Functions

Page 89

When you use the 1Seg antenna, pull it out

completely. If you apply excessive force upon it while it is not pulled out completely, it can be damaged.

Setting channels

To watch 1Seg, you need to set the channels and select an area with channels set in advance. You can register up to ten areas. You can

Perform channel setting inside the area of a

terrestrial digital TV broadcasting service with the 1Seg antenna fully pulled out.

In the application screen, [One-Seg]

: Only when channels are not set, the channel

setting screen appears.

Select a region

Select a prefecture

Select a locality

: Searching for broadcast stations starts.

[OK]

You cannot use 1Seg overseas since the

broadcasting format and the broadcasting frequency are different (You can watch 1Seg programs video-recorded on the FOMA terminal).

1Seg TV

Watch 1Seg.

In the application screen,

[One-Seg]/[One-seg TV]

: To adjust the volume: x/y : To end 1Seg: {

･ 1Seg is not ended by touching [Y] in the

Multi Assistant (Multitask) screen (P. 42) and deleting 1Seg from the list of functions being activated.

While watching 1Seg, colors in the screen may

appear differently.

Even if the home screen is displayed while

watching 1Seg, you can hear 1Seg sound. Information of data broadcasting/data broadcasting site may be automatically updated since 1Seg is kept being activated. Note that packet transmission charge may be incurred.

When you have a phone call while watching

1Seg, resume 1Seg after the call is terminated. While recording 1Seg, recording continues in the background.

Convenient Functions

Page 90

■ 1Seg watching screen layout

1 Image 2 Caption

Captions are not available depending on

programs.

3 Data broadcasting

You can use a variety of information including

still pictures and video. For example, you can connect sites available in programs, submit your opinion, etc.

4 Data broadcasting operation panel

■ Main touch panel operation in 1Seg

watching screen

While watching on the horizontal view, the

following operation is available with displayed keys when the screen size setting is [Normal].

[b]/[c]

* Touch the image to display.

The following touch operations are available.

Display/Hide the program information

Switch 2D/3D

Touch the image

Display/Hide the 1Seg operation panel

Select a station with UP/DOWN

Display channel switch screen

1Seg operation panel

The following operations are available with

displayed keys.

[@]/[A]

[D]/[E] Start/Stop recording

[Select channel] Display a screen for

[F]/[G]

*1 Touch the key for a while to select a station

by searching a frequency.

*2 Appears only on horizontal view.

Data broadcasting operation panel

The following operations are available with

displayed keys while displaying data broadcasting.

[B]/[C] Move the cursor up/down [?] Connect to the data

[>] Return to the previous

[1] to [9], [0], [#],

[＊]

Touch the program information

Slide the image to the left/ right

Touch the image for a while

Select a station with UP/ DOWN

switching channels

Switch the screen size setting

broadcasting site pointed by the cursor

page of the data broadcasting site

Select a corresponding item

Convenient Functions

Page 91

* Displayed/Not displayed depending on the

data broadcasting.

Recording 1Seg

Estimated number of saved entries and recording time

Number of

microSD Card (2 GB)

Up to 2 GB or 24 hours of video can be recorded

for each time. Even if you are using a microSD Card of more than 2 GB and its free space is sufficient, the recording up to that point is saved and recording will be stopped.

When you run out of free space on microSD

Card, recording stops automatically, and the recording up to that point is saved.

In the 1Seg watching screen, [D]

[E] to stop recording

: Recording is stopped and the video is

automatically saved.

Recording of some programs may be

prohibited.

When the time set for recording arrives while

another video is being recorded, the recording of the timer-set video is started. Recording up to that point is stopped, and the video data is saved.

The FOMA terminal does not support Dubbing

10.

saved entries

Up to 99 Up to approx.

Recording

time

600 min

Playing recorded 1Seg video

Play a recorded video saved in microSD Card.

In the application screen,

[One-Seg]/[Play One-seg Recording]

Select a video

When a video edited (split) by other devices is

played, the image or sound may be interrupted.

When a video is played, the information for the

broadcast station from which that video was recorded is displayed.

■ Main touch panel operation in video

playback screen

Basic operations in video playback screen are

the same as those in 1Seg watching screen. Operations that differ are mainly explained here.

The following operations are available with

displayed keys.

[5]/[4] Pause/Play [6]/[7] [8]/[9]

[:]/[;] Return to a location of

*1 Every time you touch it, the speed is

increased in stages.

*2 Displayed only when playback is paused.

Fast reverse/forward

Frame-by-frame reverse/ Frame-by-frame forward

approx. 15 seconds before/Skip to a location of approx. 30 seconds after

Convenient Functions

Page 92

TV Link

You can register memo information and URLs of related sites as TV Link in some data broadcasting. If they are registered as TV Link, you can check them from the TV Link screen.

You can register up to 50 TV Links. Procedures for registering TV Links differ

depending on the program.

In the application screen,

[One-Seg]/[TV Link]

: Display the registered TV Link.

Select a TV Link

Recording/Viewing reservation

You can set a timer for watching or recording 1Seg program. In addition, you can check the reservation status and result. You can save up to 50 timer settings for watching

or recording 1Seg programs.

Multiple programs cannot be watched/recorded

simultaneously. If the recording period you are about to set overlaps with that of an existing timer-set program, a confirmation screen for setting appears. Check the contents of the message, and then perform registration.

In the application screen,

[One-Seg]/[Record/View Reservation]

: Reservation list screen appears.

z/[New reservation]/[Viewing

reservation]/[Recording reservation]

Set each item/[Save]/[YES]

Reservation type: Switch Viewing

reservation/Recording reservation.

Channel: Set the channel. Start time: Set the start time. End time: Set the end time. Program: Enter the program name. Repeat: Set the repetition of the reservation.

Depending on usage of the FOMA terminal,

available memory of microSD Card or the program type, you cannot watch/record the program or recording will be stopped even if it is not finished yet.

Settings

You can set data broadcasting and auto exit time of 1Seg.

In the application screen,

[One-Seg]/[Settings]

Select an item

Set broadcast data: Set data broadcasting. Auto exit time: Set time to end 1Seg

automatically.

[Set broadcast data]

When Connection setting is disabled, a

confirmation screen for data broadcasting does not appear and information of data broadcasting/data broadcasting sites may be updated automatically. Note that packet transmission charge may be incurred.

Convenient Functions

Page 93

[Auto exit time]

When the set time for auto exit arrives while

recording a video, the display returns to the home screen and the recording continues in the background.

Osaifu-Keitai

DOCOMO shall not be liable for any loss or

change of data in the IC card or the damage of Osaifu-Keitai service caused by any reason such as malfunctions and upgrading.

When the FOMA terminal is stolen or lost,

immediately contact your provider of Osaifu-Keitai compatible service for handling methods.

Osaifu-Keitai

Osaifu-Keitai is a function which has built-in IC card and allows you to pay, use as coupons or collect stamps by simply holding the FOMA terminal over the scanning device at stores. Moreover, you can access sites and web pages by holding the FOMA terminal over the scanning device, and get the latest coupon, deposit electronic money and check your usage by using transmission. In addition, for your secure use, you can lock functions of Osaifu-Keitai when you lost the FOMA terminal. For details on Osaifu-Keitai, refer to “Mobile Phone User’s Guide [sp-mode]” (in Japanese only). ※To use Osaifu-Keitai compatible service, settings

are necessary from a website or an application.

FOMA terminal malfunctions may cause data

(including electronic money, points, etc.) saved in the IC card to be lost or changed (Note that as a rule, you will be asked to delete data when leaving your FOMA terminal for repairs, etc.). For the service such as a reissue, restoration, temporary keeping or transfer of the data, contact your provider of Osaifu-Keitai　 compatible service. Be sure to use a service including a backup service for important data.

Using Osaifu-Keitai

To use Osaifu-Keitai compatible services,

download a Osaifu-Keitai compatible application from Osaifu-Keitai compatible sites and make the setting. Some services do not need to download a Osaifu-Keitai compatible application.

In the application screen, [おサイフ

ケータイ] (Osaifu-Keitai)

: If the initial setting is not completed, the initial

setting screen appears.

Select a service

You cannot use Osaifu-Keitai in the following

situations. However, you can pay by holding the FOMA terminal over a scanning device.

In Offline mode When you are charging the FOMA terminal,

connecting a microUSB cable for PC (sample) to it or connecting an earphone to it while the UIM is not inserted/When the FOMA terminal has never received radio wave

Convenient Functions

Page 94

Holding over scanning device

mark

Hold the a mark of the FOMA terminal over the scanning device to use as electronic money or railway tickets or to retrieve ToruCa. Pay attention to the following points when

holding the a mark over the scanning device. Do not contact between the FOMA terminal

and the scanning device

Hold the a mark parallel over the scanning

device

Hold the a mark over the center of the

scanning device

If the scanning device does not recognize,

hold the a mark over the scanning device and move the handset around

Do not attach a metallic substance on the a

mark side

Hold the a mark over the

scanning device

Confirm that the data is scanned

Osaifu-Keitai lock setting

Lock the Osaifu-Keitai function. Perform the same operation to disable the lock.

In the service list screen, z/[お

サイフケータイロック設定] (Osaifu-Keitai lock setting)/[Next]

Enter the Lock No./[OK]/[Next]

ToruCa

ToruCa is an electronic card that can be imported to the FOMA terminal. You can retrieve it as store information or a coupon from a scanning device or sites. Retrieved ToruCa is saved in the “ToruCa” application and you can display/search/update it using the application. For details on ToruCa, refer to docomo market.

In the application screen, [ToruCa]

Normal packet transmission charges may be

incurred for retrieving, displaying or updating ToruCa.

ToruCa provided for i-mode terminals may not

be retrieved/displayed/updated.

The following functions may not be used

depending on the settings of IP (Information Provider).

Retrieving from a scanning device Updating Sending through mail Moving or copying to a microSD Card Displaying a map

A map may not be displayed from the ToruCa

list although it can be from ToruCa (details) depending on the settings of IP.

When Osaifu-Keitai is locked, you cannot

retrieve ToruCa from a scanning device.

Convenient Functions

Page 95

When checking for duplicate is set on, you

cannot retrieve the duplicate ToruCa. If you want to retrieve it, set “OFF” checking for duplicate.

When you send ToruCa through mail, it is sent

in the status that the ToruCa (details) has not been retrieved.

ToruCa received through mail may not be

saved depending on the mail application.

ToruCa may not be retrieved depending on the

browser you use.

When you move or copy ToruCa to microSD

Card, it is sent in the status that the ToruCa (details) has not been retrieved.

“ToruCa” application cannot be deleted.

If the initial setting of Osaifu-Keitai has not

made, ToruCa may not be retrieved from a scanning device.

Calendar

Manage schedules by using the calendar.

In the application screen,

[Calendar]

Select the date on which you

Select the time at which you

What: Enter the title. From: Set the start time. To: Set the end time. All day: Switching All day setting. Where: Enter the place.

Description: Enter the details. Calendar: Set the calendar sheet. Guests: Enter the mail address of the guests

you invite.

Repetition: Set the repetition. Reminders: Set how long before the start

time it reminds you of the schedule.

Alarm/Timer

Alarm

Activate an alarm tone or vibrator at the specified time/day of week. You can save up to ten alarms.

In the application screen, [Alarm/

Timer]/[Alarm]

Select a register destination

Set each item

Name: Enter the name. Enable/disable alarm: Enable/Disable the

alarm settings.

Time: Set the time when the alarm rings. Ring duration: Set the alarm duration. Repeat: Set the repetition of the alarm. Alarm sound: Set the alarm sound. Alarm volume: Set the alarm volume. Enable/disable snooze: Enable/Disable the

snooze setting.

Snooze interval: Set the snooze interval. Snooze repeat: Set the number of snooze

repeat.

Vibrator Setting: Enable/Disable the vibrator

setting.

Convenient Functions

Page 96

The alarm is not activated when the handset is

turned off at the alarm setting time.

The alarm is not activated when the set time

arrives during a call. Upon the end of the call, the previously displayed screen or the home screen is returned, and the alarm is activated.

When a set time arrives during another alarm

sounding, the alarm is delayed. When the former alarm stops or the alarm duration has elapsed, the delayed alarm restarts.

■ Touch panel operation when an alarm

sounds

The following touch operations are available.

End the alarm Keep touching [2] and

Stop the alarm (Snooze works)

slide to the right following the arrow on the screen

Keep touching [3] and slide to the left following the arrow on the screen

Stopwatch

In the application screen, [Alarm/

Timer]/[StopWatch]

[Start]

: To record the lap time and split time: [Lap]

[Stop]

: To reset measured time and history: [Reset]

You can record up to 99 histories of lap time

and split time. When the number exceeds 99, they are deleted starting with the oldest.

Measured time and history are reset by ending

the alarm/timer.

Convenient Functions

Timer

Activate an alarm tone or vibration after the specified length of time passes.

In the application screen, [Alarm/

Timer]/[Timer] Touch the set time/enter the

time/[OK]

: Touch [10sec]/[1min]/[5min]/[10min] to plus

10 seconds/1 minute/5 minutes/10 minutes to the set time.

: To reset the set time to 00 minute 00 second:

[Reset]

[Start]

: To cancel the countdown: [Reset]

[Stop]

Notepad

In the application screen,

[Notepad]/[Create] Enter the body text/[Save]

Voice Recorder

You cannot record when the available space of

the microSD Card is less than 300 KB.

In the application screen, [Voice

Recorder]

: To switch recording mode: [Mode]

Page 97

･ When [Attach to Mail mode] is set, the limit

of the recording time is set to the size that can be attached to mail. When [Long time mode] is set, you can record up to 6 hours per recording.

[p]

: Recording start sound is heard and recording

starts. Incoming lamp flashes during recording.

[q]

: Recording stop sound is heard and recorded

data is saved.

Recording start/stop sounds are enabled

regardless of the setting of the FOMA terminal.

Recording stops automatically when recording

time reaches the maximum or when the microSD Card has no available space.

When a call is received during recording,

recording automatically stops, recorded data is saved, and the call can be answered. After the call ends, the save completion notification screen appears.

■ Playing recorded data

In the Voice Recorder screen, [Play]

: Previously recorded data is played by

operating after recording.

Select recorded data

When a call is received during playing, playing

is automatically paused and the call can be answered. After the call ends, the play screen appears while pausing data.

Calculator

In the application screen,

[Calculator]

Calculate

When the calculator is ended, memories are

deleted.

Results or history information may be deleted

while it is active in the background.

Dictionary

Enter the keyword and search for it in the Built-in or Net Dictionary.

The following e-dictionaries are preset on the

FOMA terminal (Part of the dictionary may differ from printed version due to computerization). 明鏡国語辞典MX

Containing approximately 58,000 words

centered around frequently used modern

language. ジーニアス英和辞典MX

An English-Japanese dictionary, which is

convenient for English conversation, reading

newspapers and novels. Containing

approximately 89,000 words. ジーニアス和英辞典MX

A full-fledged words Japanese-English

dictionary contains approximately 69,000

words centered around modern language. (“明鏡国語辞典MX” ©KITAHARA Yasuo & Taishukan, 2009, “ジーニアス英和辞典MX”, “ジーニアス和英辞典MX” ©KONISHI

Tomoshichi, MINAMIDE Kosei & Taishukan,

2009)

Convenient Functions

Page 98

Net Dictionary “百科事典” (encyclopedia) is

available by default.

In the application screen,

[Dictionary]

: To switch dictionaries: [Switch dictionary]/

select a dictionary to use

Enter the keyword

: In the Built-in Dictionary, the search result

appears every time text is entered.

: In the Net Dictionary, the search result

appears after entering the keyword/ [Search].

Select a search result

Android Market

Market

By using Android Market, you can access to useful applications or fun games directly, that can be downloaded and installed to the FOMA terminal. Enable Background data (nP. 67) in advance.

In the application screen, [Market]

Be sure to check the security of application,

then install it at your own risk. The FOMA terminal may be infected with a virus or data may be damaged.

Note that DOCOMO shall not be liable for

malfunctions caused by the application you installed.

Note that DOCOMO shall not be liable for any

disadvantage brought to you or any third party due to the application you installed.

Installing application

In the Android Market screen,

select an application to download/ [Install]/[OK]

Once you accept the installation of application,

you are responsible for the results of using the application. Be very cautious about installation of applications that have access to many functions or a significant amount of data.

Purchasing application

When downloading a charged application, you

need to create a Google Checkout account to purchase the application.

In the Android Market screen,

select an application to purchase/ [Buy]

: If you make a purchase for the first time, sign

in Google Checkout payment and billing service.

You pay for the application only once.

Uninstalling after download and downloading again later are not charged.

If you have multiple Android devices that use

the same Google account, you can download the purchased application to all of them at no additional cost.

DOCOMO holds no responsibility for

responding to purchase applications and get refund from the Android Market.

Convenient Functions

Page 99

■ Requesting refund

You can ask for a refund within 24 hours of the purchase of application. The application is deleted and you are not charged. In addition, note that a refund request is available for each application only once. If you requested a refund for the purchased application in the past and purchase the same application again, a second refund request is not available.

In the Android Market screen,

[Downloads] Select an application to uninstall/

[Uninstall]/[OK] Answer the survey form/[OK]

docomo market

In docomo market, you can quickly access DOCOMO recommended sites and useful applications.

In the application screen, [docomo

market]

Packet transmission (3G) or Internet

connection via Wi-Fi is required to use docomo market.

Packet transmission charge is incurred

separately for connecting to docomo market and downloading applications introduced on docomo market. Some applications automatically perform packet transmission.

Applications introduced on docomo market

include charged ones.

DOCOMO shall not be liable for any

disadvantage caused by sites introduced on docomo market or the information acquired from the sites.

DOCOMO shall not be liable for contents,

adequateness to purpose of use, reliability, etc. of applications introduced on docomo market.

Some applications that you perform installation

may give your FOMA terminal instability of the operation or may send your location information or personal information registered in the FOMA terminal to outside via the Internet and the information may be used improperly. Please thoroughly check a provider and operation condition of the application, etc. before using it.

The copyrights of materials (documents,

photographs, illustrations, animations, sounds, software, etc.) on this site are the possession of DOCOMO or other third parties and are protected by the Copyright Act as well as other laws and agreements. Excluding the extent of quotation and reproduction for private use that is approved in the Copyright Act, without the consent of the party owing the copyright, the reproduction, adapting or public transmission of copyrighted material is prohibited.

Convenient Functions

Page 100

Infrared communication

Using infrared communication

Use infrared communication to send and receive data to and from other FOMA terminals which also support infrared communication. Send and receive phonebook entries, profile,

notepad, bookmark, mail, data shot by camera, data in Gallery (3D), data recorded with Voice Recorder and data in Contents Manager, etc.

The FOMA terminal infrared communication

function complies with IrMC™ 1.1 standard. However, depending on the function, some data may not be sent or received even when the other party’s terminal complies with IrMC™ 1.1 standard.

The FOMA terminal Ir send and receive functions

comply with IrSimple™ standard.

Infrared communication is not available in Offline

mode.

To enter Lock No. and authentication code are

required for sending or receiving all data items. The authentication code is a password exclusively for infrared communication. Before starting data transmission, the sender and receiver must enter the same user-specified four-digit code.

■ When using infrared communication

15°

Infrared port

Approx. 20 cm or less

Face the Infrared ports of the receiver’s and

sender’s FOMA terminal each other and set the distance between them to approximately 20 cm or less as shown.

While doing infrared communication, keep the

Infrared ports facing each other and do not move.

Infrared communication may not function

properly in areas of direct sunlight, directly under fluorescent lights or near other equipment using infrared signals.

If either of the Infrared ports is dirty, infrared

communication will become difficult. Take care not to scratch the ports, and wipe off any dirt with a soft cloth.

Convenient Functions