SHARP LQ121S1LG88 Specification

SPEC No.

RECORDS OF REVISION

LQ121S1LG88

DATE SUMMARY

REVI

SED

No

PAGE

NOTE

LD-24604A -

LD-24604B

LD-24604C

2012/6/26

2013/1/30

2013/4/16

1 15 Added Lot No display method.

2 8 Description of the pull-down resistor has

been removed.

- Contents -

No. page

1 Application ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 1

2 Overview ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2

3 Mechanical Specifications ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 2

4 Input Terminals ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 3

5 Absolute Maximum Ratings ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 6

6 Electrical Characteristics ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 7

7 Timing characteristics of input signals ・・・・・・・・・・・・・・・・・・・・・・ 9

8 Input Signals, Basic Display Colors and Gray Scale of Each Color ・・ 10

9 Optical Characteristics ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 11

10 Handling Precautions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 13

11 Packing form ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 14

12 Reliability test items ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 14

13 Others ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 15

14 Storage conditions ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 16

Fig.1 OUTLINE DIMENSIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 17

Fig.3 PACKING FORM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・ 18

LD-24604C- 1

1．Application

This specification applies to the color TFT-LCD module LQ121S1LG88.

This specification is the proprietary product of SHARP CORPORATION (SHARP) and include

materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in

any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express

written permission of SHARP.

The device listed in this specification was designed and manufactured for use in general electronic

equipment.

In case of using the device for applications such as control and safety equipment for transportation (controls of

aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which

require higher reliability and safety, take into consideration that appropriate measures such as fail-safe

functions and redundant system design should be taken.

Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,

telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment

for life support.

SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply

with the instructions and the precautions specified in this specification .

Contact and consult with a SHARP sales representative for any questions about this device.

LD-24604C- 2

2．Overview

　　 This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor).

　　It is composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit and a White-LED

　　Backlight unit. Graphics and texts can be displayed on a 800×RGB×600dots panel with about 262144

　　colors by using LVDS (Low Voltage Differential Signaling) and supplying +3.3V DC supply voltages for

　　TFT-LCD panel driving and supply voltage for backlight.

The maximum viewing angle is in the 6o'clock direction.

The 12o'clock direction is difficult to reverse the grayscale.

By the independent RGB gamma adjustment function, this module can display natural gray scales.

The LED driver circuit and the PWM circuit to drive the backlight are built into the module.

3．Mechanical technical literatures

Parameter

Display size

Active area

Pixel format

Aspect ratio

Pixel pitch

technical literatures

31（12.1inch）Diagonal

246（H)×184.5（V)

800（H)×600（V)

(1pixel＝R＋G＋B dot)

4：3

0.3075（H)×0.3075（V)

Unit

cm

mm

pixel

mm

Pixel configuration

Display mode

Unit outline dimensions

【*1】

Mass

Surface treatment

【*1】 Excluding the protrusion of the connector cover from thickness.

Outline dimensions are shown in Fig.1.

R,G,B vertical stripe

Normally white

276.0（W)×209.0（H)×9.1(D)

750 （Max.）

Anti-glare and hard-coating 3H

mm

g

4．Input Terminals

4-1．TFT-LCD panel driving

CN1（Interface signals and +3.3V power supply）

Using connectors：FI-SEB20P　(Japan Aviation Electronics industry Co., Ltd.)

Corresponding connectors：FI-SE20M or FI-S20S　(Japan Aviation Electronics industry Co., Ltd.)

Using LVDS receiver：Building into cotroll IC (THC63LVDF84B(Thine electronics) or Compatible product)

Corresponding LVDS transmitter：THC63LVDM83R（Thine electronics) or Compatible product

CN1

LD-24604C- 3

Pin

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

Symbol

VCC
VCC
GND

GND
RxIN0­RxIN0+

GND
RxIN1­RxIN1+

GND
RxIN2­RxIN2+

GND
CK IN­CK IN+

Function

+3.3V Power supply
+3.3V Power supply

GND

GND
LVDS receiver signal CH0 (-)
LVDS receiver signal CH0 (+)

GND
LVDS receiver signal CH1 (-)
LVDS receiver signal CH1 (+)

GND
LVDS receiver signal CH2 (-)
LVDS receiver signal CH2 (+)

GND

LVDS receiver signal CK (-)
LVDS receiver signal CK (+)

Remark

LVDS
LVDS

LVDS
LVDS

LVDS
LVDS

LVDS

LVDS
16
17
18
19
20

【*1】 　RL/UD = LOW 　RL/UD = HIGH

CN1

GND

NC

RL/UD 【*1】Horizontal/Vertical display mode select signal

GND
GND

GND

Non Conection

GND
GND

CN1

RxCKIN+
RxCKIN-

LD-24604C- 4

1 CYCLE

RxIN0+
RxIN0-

RxIN1+
RxIN1-

RxIN2+
RxIN2-

R1 R0 G0 R5 R4 R3 R2 R1 R0 G0

G2 G1 B1 B0 G5 G4 G3 G2 G1 B1

B3 B2 DE (VS) (HS) B5 B4 B3 B2 DE

DE：DATA ENABLE

HS：Hsync

VS：Vsync

NA：Non Available

4-2．Interface block diagram

(Computer　Side)

(TFT-LCD side)

Controller

R0-R5,G0

G1-G5,B0,B1

B2-B5, (HS,VS),DE

ALL GND

CK

7

　TA 0 - 6

7

　TB 0 - 6

7

　TC 0 - 6

7

TD 0 - 6

CＬK IN

THC63LVDM83R

TTL PARALLEL-TO-LVDS

PLL

RXIN0+

RXIN0-

RXIN1+

RXIN1-

RXIN2+

RXIN2-

RXCKIN+

RXＣKIN-

Single LVDS interface contained in a control IC

LVDS-TO-PARALLEL TTL

PLL

　RA 0 - 6

　RB 0 - 6

　RC 0 - 6

CK OUT

Internal circuits