Date: Jan. 30, 1997
LASER PRINTER: JX-9210
(Parts Change Information)
1.DISCONTINUATION OF THE PROTECTOR CAP.
2.CHANGE IN THE SHAPE OF THE PU TRAY.
3.UNIFICATION OF THE PARTS CODE FOR THE MAIN MOTOR
CONNECTOR OF THE MAIN PWB .
1. Discontinuation of the protector cap.
1.Model Name: JX-9200/9210
2.General: The protector cap which has been attached as a measure to prevent static electricity
has been discontinued, and packing tape has been attached to the centro-connector in
its place.
No. : LPE-263
3.Description: The protector cap (PCAPH1001ACZZ) has been discontinued, and packing tape has
been attached as described in the figure shown below.
Packing tape
The upper and lower edges of the packing tape have been attached in a manner such
that the connector is enveloped by the tape, and the end of the tape has been folded
over so that the tape can be easily removed.
4.Action: From 1996 November production.
SHARP CORPORATION Printer and Scanner Division
1/3
Orange
C
2. Change in the shape of the PU tray.
1.Model Name: JX-9200/9210
2.General: There is a possibility of problems occurring in the movement of the PU tray have
occurred because the opening between the PU tray and the rear cabinet is too narrow.
As a measure to alleviate this danger the thickness of the PU tray has been cut away to
widen the space between the PU tray and the rear cabinet.
3.Description: A change in the shape has been carried out as described in the figure shown below.
A change in the part code has also been carried out in accordance with this change.
Old New
PU Tray LSOU-0007GCZZ LSOU-0007GCZ2
Raised ridge line R0.5 → R1.0
Raised ridge line R0.5
Gradient 0°
Cut-away section
No change has been carried out in the position of the raised ridge lines.
Approximately 1mm
The gradient has been changed from 0° to 3°.
No change
Raised ridge line R1
Gradient 3°
4.Action: Japanese domestic production: From 1996 mid-September production.
SOCC production: From 1996 October production.
2/3
3. Unification of the parts code for the main motor connector of the main PWB.
1.Model Name: JX-9200/9210
2.General: In the case of the main motor connector of the main PWB, two part codes had been
established for the same part. To alleviate this problem, the two part codes have been
unified into a single part code.
3.Description: Old New
Main motor connector QCNCM0054GCZZ QCNCM0876FCZZ
4.Action: From 1996 October production.
Ref.
Model
No.
JX-9200
JX-9210
<Interchange>
1. Interchangeable. 4. Not interchangeable.
2. C urr e nt t y pe c a n be u s ed i n p la ce of new t ype .
New ty pe cann ot be us ed i n place of curr ent type .
3. C urre nt ty pe cann ot be used i n place of new ty pe.
New t y pe c a n be u sed in p la c e of c u rr en t ty p e.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
name
Version P/G No.
1 -43 PCAPH1001ACZZ — — Protector cap ’96/11 6
2 -5 LSOU-0007GCZZ LSOU-0007GCZ2 AP PU tray
All
7 -84
!
Current parts New parts
Parts code Parts code
QCNCM0054GCZZ QCNCM0876FCZZ AB
Price
rank
5. Interchangeable if replaced with same types of
relate d parts in use .
6. Others .
Parts name
Main motor
connector
Effec-
tive
time
Mid-
’96/9
’96/10 1
Inter-
change-
ability
3
Note
3/3
Loading...