Sharp LL-171ME OPERATION MANUAL

Download

LCD Multimedia Monitor LCD Multimedia Monitor Moniteur LCD Multimédia LCD Multimedia Monitor

LL-171ME

OPERATION MANUAL BEDIENUNGSANLEITUNG MODE D’EMPLOI MANUALE D’USO

EnglishDeutschFrançaisItaliano

English ....... E1

Deutsch ......G1

Français ..... F1

Italiano ........IT1

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/ EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ, óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/ 68/EEC.

CAUTION:

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION:

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT:

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L’APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING:

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION:

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

PRECAUCION:

A FIN DE EVITAR DESCARGAS ELÉCTRICAS, DESCONECTE EL ENCHUFE DE LA RED ANTES DE REALIZAR CUALQUIER OPERACIÓN DE SERVICIO.

ATTENZIONE:

PER EVITARE FOLGORAZIONI, SCOLLEGATE IL CAVO DI COLLEGAMENTO ALLA RETE IN ALTERNATA PRIMA DI EFFETTUARE UN INTERVENTO DI SERVIZIO TECNICO.

ATTENZIONE:

PER UNO SCOLLEGAMENTO ELETTRICO COMPLETO, TIRATE FUORI LA SPINA PRINCIPALE.

ENGLISH

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW : Earth BLUE : Neutral BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth

• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.

• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.

Ensure that your equipment is connected correctly. If you are in any doubt consult a qualified electrician.

“WARNING: THIS APPARATUS MUST BE EARTHED.”

or coloured green or green-and-yellow.

EnglishDeutschFrançaisItalianoEspañolEnglish

Table of Contents

Getting started

Tips and safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E4

Monitor and accessory checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E5

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6

Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E6

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E7

Cable clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8

Using headphones (commercially available) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8

Angle adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E8

Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9

Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9

Batteries for the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E9

Connection and preparation

Connecting the monitor to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E10

Antenna connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E11

Connecting the monitor to AV equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E12

AV equipment with 21-pin Euro-SCART (RGB) terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E12

AV equipment with video output terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E12

AV equipment with S-video output terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E13

Connecting the monitor to a power source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E14

First installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E15

Selecting the item in the MENU screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E16

Adjusting the computer display (AUTO ADJUSTMENT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E17

Common operations

Common operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18

Turning power on/off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18

Switching display modes (INPUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E18

Adjusting the volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19

Adjusting the backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19

Selecting the language on the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E19

PC mode

Watching TV or other video in a window on the computer screen (PICTURE IN PICTURE) . . . . . . . . E20

Selecting the video and audio sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E20

Listening to TV or another audio source while viewing the computer screen . . . . . . . . . . . . . . . . . . . . E21

Adjusting the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22

How to adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E22

ADJUSTMENT menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E23

GAIN CONTROL menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E24

COLOUR CONTROL menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E24

MODE SELECT menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E25

PICTURE IN PICTURE menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E25

Installing set-up information and the ICC profile (For Windows) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E26

Information about the ColorSync profile (For MacOS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E29

Table of Contents

TV/AV mode

Setting TV channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E30

Saving broadcast TV channels in the memory (AUTOMATIC SEARCH) . . . . . . . . . . . . . . . . . . . . . E30

Adjusting the individual settings of programmes (MANUAL ADJUSTMENT) . . . . . . . . . . . . . . . . . E31

Changing the programme positions (SORT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E32

Erasing the programme range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E32

Enter/change the name of an individual programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E33

Watching TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E34

Selecting the channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E34

Selecting the channels using the programme table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E34

Selecting the audio reception mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E35

Watching Teletext . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E36

Using the Child Lock function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E39

Enjoying DVDs, games, and other equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E42

Handy features (for TV/AV mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E43

Pausing the screen (FREEZE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E43

Returning to previous channel (FLASHBACK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E43

Switching power off after a specified length of time (SLEEP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E43

Adjusting the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E44

How to adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E44

PICTURE menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E45

PROGRAMMES menu (TV mode only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E45

AV CONNECTIONS menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E45

MODE SELECT menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E46

CHILD LOCK menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E46

EnglishDeutschFrançaisItalianoEspañolEnglish

Other features

Other features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E47

Checking the current channel and audio reception mode on screen (DISPLAY) . . . . . . . . . . . . . . E47

Changing BRIGHT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E47

Muting the sound (MUTE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E47

Changing the screen size (VIEW MODE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E47

Preventing changes to adjusted values (ADJUSTMENT LOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . E48

Resetting all adjustment values (ALL RESET) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E48

Instructions for attaching a VESA-compliant mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E49

Appendix

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E50

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E50

Monitor care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E51

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E51

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E52

Tips and safety precautions

Thank you for your purchase of the Sharp LCD Multimedia Monitor. To ensure safety and many years of trouble-free operation of your product, please read the safety precautions carefully before using this monitor.

- The TFT colour LCD panel used in this monitor

is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colours or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.

- Do not leave the screen displaying idly for long

periods of time, as this could cause an afterimage to remain.

- If the brightness is adjusted to the minimum

setting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using a computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

- This monitor and its accessories may be

upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam, as this could lead to fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to fire or electric shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the monitor to come into contact with strong shocks or vibrations. Causing the monitor to fall or topple over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating equipment or anywhere else where there is likelihood of high temperature, as this may lead to generation of excessive heat and outbreak of fire.

The Power Cord

- Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords. Damage to the cord may result in fire or electric shock.

- Use only the power cord supplied with the monitor.

- Insert the power plug directly into the AC outlet. Adding an extension cord may lead to fire as a result of overheating.

- Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.

Use of AC adapter

- Do not use the AC adapter for other than the specified equipment.

- Unplug the AC adapter if it is not used for long time.

- Do not place any objects on the AC adapter.

- Do not use the AC adapter outdoors.

- Do not attempt to repair the AC adapter if it is broken or malfunctioning. Refer the servicing to the service representative.

- Do not try to open the AC adapter.

- Do not use water or wet cloth for cleaning the AC adapter.

Manual Scope

- In this manual, Microsoft Windows XP will be referred to as “Windows XP”, Microsoft Windows Millennium as “Windows Me”, Microsoft Windows 2000 as “Windows 2000”, Microsoft Windows 98 as “Windows 98”, Microsoft Windows 95 as “Windows 95”, and Microsoft Windows Version 3.1 as “Windows 3.1”. When there is no need to distinguish between programmes, the term “Windows” will be used.

- Microsoft and Windows are registered trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple Computer, Inc.

- All other brand and product names are trademarks or registered trademarks of their respective holders.

Monitor and accessory checklist

Please check that the following items are included in the package.

- LCD multimedia monitor (1) AC adapter (1)

(model name: NL-A69J)

Power cord (1)

- PC analog signal cable (1) (model name: 0NIT15V1-0183) PC audio cable (1)

(model name: 0NIT17A3-U006)

Remote control (1)

- R-03 (“AAA” size, UM/SUM-4) dry battery (2)

- Cable clamp (1)

- CD-ROM (Utility Disk for Windows/Macintosh) (1)

- Operation manual (1)

Notes:

- You are advised to retain the carton in case the monitor needs to be transported.

- Sharp Corporation holds authorship rights to the Utility Disk programme. Do not reproduce it without permission.

- The shape of the supplied accessories may not be exactly same as shown in this manual.

EnglishDeutschFrançaisItalianoEspañolEnglish

Main unit

Product description

Front view

1. Speakers

2. Power LED

Green: in use Red: in standby mode Orange: in power-saving mode

(only for PC mode)

Off: power off

3. Remote sensor window

4. Headphone terminal

Right view/rear view

6 7

5. INPUT button

6. MENU button

7. OK/BRIGHT MODE button

8. (channel) buttons

9. ( (volume) /BRIGHT) buttons

10. MAIN POWER button

11. PC audio input terminal

12. PC analog RGB input terminal

13. Power input terminal

11 12 13

Removing/replacing the terminal cover

Removing the cover

Replacing the cover

Product description

Main unit

Left view/rear view

14.Handle

15. 21-pin Euro-SCART (RGB) terminal

16. Video input terminal

17. Audio input terminal - Left

18. Audio input terminal - Right

19. S-video input terminal

20. Antenna input terminal

21. Lug-hole for cable clamp (See next page.)

A Ventilation openings

Never block the ventilation openings as this may lead to overheating inside the monitor and result in malfunction.

B Security lock anchor

By connecting a security lock (commercially available) to the security lock anchor, the monitor is fixed so that it cannot be transported. The security slot works in conjunction with Kensington Micro Saver Security Systems.

AV-IN1

AV-IN2

Remote control

POWER

2 3

SUBPAGE SUBTITLE

SLEEP

16 17 18 19

BRIGHT

MODE

7 8

DISPLAY

1. POWER button

2. SUBPAGE button

3. REVEAL button

4. SLEEP button

buttons and OK button

6. BRIGHT MODE button

7. Red, Green, Yellow and Cyan buttons (for Teletext)

8. DISPLAY button

9. FREEZE/HOLD button

10. Channel buttons

11. (flashback) button

12. VIEW MODE button

13. PIP (Picture in Picture) button

14. Input buttons (PC, TV, AV1, and AV2)

15. TEXT button (for Teletext)

16. SUBTITLE button

17. MENU button

18. BRIGHT button

19.

(mute) button

20. SOUND button

(volume) + – buttons

21.

22. (channel) buttons

PC AV2AV1TV

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

12 13 14

15 16 17

19 20

EnglishDeutschFrançaisItalianoEspañolEnglish

Product description

Cable clamp

Use the supplied cable clamp to secure the cables connected to the terminals.

CAUTION!

- When adjusting the viewing angle, cables may be pulled. Therefore, ensure that the cables have sufficient slack.

Angle adjustment

Adjust to an easy to view angle.

CAUTION!

- Be sure to hold both sides of the monitor when adjusting the viewing angle. The LCD panel used in this monitor is made of glass. Pressure from hands on the LCD panel could cause damage.

- Be careful not to allow your fingers to be pinched.

approx. 20°

approx. 5°

Using headphones (commercially available)

You can connect headphones (commercially available) to the monitor.

Headphone terminal

Headphones

Note:

- When the headphones are connected, no sound can be heard from the monitor speakers.

Remote control

Using the remote control

Use the remote control by pointing it towards the remote sensor window on the monitor. Objects between the remote control and sensor window may prevent proper operation.

Cautions regarding use of remote control

- Do not expose the remote control to shock. In addition, do not expose the remote control to liquid, and do not place in an area with high humidity.

- Do not install or place the remote control under direct sunlight. The heat may deform the unit.

- The remote control may not work properly if the remote sensor window of the monitor is under direct sunlight or strong lighting. In such case, change the angle of the lighting or monitor, or operate the remote control closer to the remote sensor window.

- Do not use the remote control simultaneously with remote controls of other equipments.

Batteries for the remote control

Before using the monitor for the first time, install two R-03 (“AAA” size, UM/SUM-4) batteries (supplied). When the batteries become depleted and the remote control fails to operate, replace the batteries with new R-03 (“AAA” size, UM/SUM-4) batteries.

EnglishDeutschFrançaisItalianoEspañolEnglish

1 Open the battery

cover.

Slide the cover while pressing the ( ) part.

CAUTION!

Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instructions below.

- Place batteries with their terminals corresponding to the (+) and (–) indications.

- Different types of batteries have different characteristics. Do not mix batteries of different types.

- Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new battery and/or cause the old battery to leak chemicals.

- Remove batteries when they become weak. Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a cloth.

- The batteries supplied with the product may have a shorter life expectancy due to storage conditions.

- If the remote control will not be used for an extended period of time, remove the batteries from the remote control.

2 Insert two R-03 (“AAA” size,

UM/SUM-4) batteries.

Position the positive and negative ends of the batteries as indicated in the compartment.

3 Close the battery

cover.

Engage the claw on the cover into the battery housing and slide shut.

Connecting the monitor to a computer

CAUTION!

- When connecting, ensure that the monitor and all the equipment you are connecting to it are switched off.

- Be careful not to over bend the cable or add extension cords as this could lead to a malfunction.

- When using the monitor for the first time or after having changed the system settings during use, perform an automatic screen adjustment (see page E17).

See page E6 for information on removing/replacing the terminal cover.

PC audio cable (accessory)

PC analog signal cable (accessory)

Audio output terminal

The monitor’s speakers will play the computer’s audio when you connect the two devices with the PC audio cable accessory.

Notes:

- Depending on the computer or OS, you may have to install the set-up information for the monitor. (See page E26.)

- When connecting to a notebook and the notebook computer’s screen is set so that it is displaying at the same time, the MS-DOS screen may not be able to display properly. In this case, change the settings so that only the monitor is displaying.

Analog RGB terminal (Mini D-sub15 pin 3 rows)

Paying attention to the connector direction, firmly insert the signal cable straight into the connector, and then tighten the screws at both ends.

If connecting to a D-sub15 pin 2 row Apple Power Macintosh, attach a Macintosh conversion adapter (commercially available) to the analog signal cable.

Power Macintosh

Macintosh conversion adapter

E10

Antenna connection

CAUTION!

- When connecting, ensure that the monitor is switched off.

To enjoy a clearer picture, we recommend that you use an outdoor antenna. Use a 75-ohm coaxial cable with a DIN45325 (IEC169-2) plug to connect the outdoor antenna to the antenna input terminal on the left side of the monitor.

75-ohm coaxial cable (round cable) (not supplied)

Antenna input terminal (ANT)

EnglishDeutschFrançaisItalianoEspañolEnglish

E11

Connecting the monitor to AV equipment

CAUTION!

- Ensure that the monitor and all the equipment you are connecting to it are switched off before you begin.

AV equipment with 21-pin Euro-SCART (RGB) terminals

Left side of the monitor

AV-IN1

Decoder etc.

21-pin Euro-SCART cable (commercially available)

AV equipment with video output terminals

Left side of the monitor

AV-IN2

(Yellow) (Yellow)

(White) (White)

(Red) (Red)

RCA pin cable (commercially available)

Note:

- When you are using the video input terminal, do not connect the cable to the S-video input terminal.

E12

VCR etc.

Connecting the monitor to AV equipment

AV equipment with S-video output terminals

Left side of the monitor

Note:

- When you are using the S-video input terminal, do not connect the cable to the video input terminal.

AV-IN2

(White) (White)

(Red) (Red)

RCA pin cable (commercially available)

S-video cable (commercially available)

VCR etc.

EnglishDeutschFrançaisItalianoEspañolEnglish

E13

Connecting the monitor to a power source

CAUTION!

- When connecting, ensure that the monitor is switched off.

- Always use the AC adapter that came with the monitor.

- Be careful not to over bend the cable or add extension cords as this could lead to a malfunction.

See page E6 for information on removing/replacing the terminal cover.

1.Connect the AC adapter to the power input terminal.

Power input terminal

AC adapter

2.Plug the power cord into the AC adapter and then place the power plug into an AC outlet.

Power cord

AC outlet

AC adapter

Note:

- The shape of the power cord may vary in some countries.

E14

First installation

When you turn on the monitor power for the first time or after the ALL RESET operation (refer to the end of this manual), the FIRST INSTALLATION routine, which makes installation easier, is activated. Using this routine, you can select the on-screen display language, and automatically search for and store the receivable channels.

Note:

- This routine activates every time you turn on the monitor power until the automatic programme search is started once.

INPUT

/BRIGHT

MAIN

POWER

BRIGHT

MODE

POWER

SUBPAGE SUBTITLE

SLEEP

BRIGHT

MODE

DISPLAY

PC AV2AV1TV

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

1. Press the MAIN POWER button to turn on the monitor. When the power LED lights red, press the POWER button on the remote control. The “FIRST INSTALLATION (LANGUAGE)” screen will be displayed.

2.Select the desired language using the MENU button (monitor) or the buttons (remote control). The on-screen display will switch to the selected language.

Notes:

- The procedures described in this manual use

screenshots in ENGLISH (factory setting).

- You can change the on-screen display

language after the FIRST INSTALLATION routine is completed. (See page E19.)

3.Press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The “FIRST INSTALLATION (AUTOMATIC SEARCH)” screen will be displayed.

FIRST INSTALLATION (AUTOMATIC SEARCH)

RETURN

[

COUNTRY COLOUR SYSTEM SOUND SYSTEM

[

PAL

[

]

START SEARCH

4.Select the desired adjustment item using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). Then select the desired item using the buttons (monitor) or the buttons (remote control).

Note:

- Select your country from the following: UK,

Germany, France, Italy or “OTHERS”. When “OTHERS” is selected, you can change the other two systems.

5.Select “START SEARCH” using the MENU button (monitor) or the buttons (remote control).

6.Press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The automatic programme search will start.

Note:

- If you want to stop the process after it has

started, press the INPUT button (monitor) or the MENU button (remote control). In this case, you can set channels using “AUTOMATIC SEARCH” in the PROGRAMMES menu in

TV mode. (See page E30.) When the search is completed, the new programmes found are displayed on the list.

START SEARCH

SEARCH IS COMPLETED

00 05 10 15

01 E02 06 11 16 02 E03 07 12 17 03 E04 08 13 18 04 09 14 19

TV/AV

Notes:

- The programmes are named automatically

and the programmes whose names could not

be found are displayed with “-----”. Names can

be entered later. (See page E33.)

- To display the previous or next list, use the

buttons (monitor) or the buttons (remote

control).

7.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

EnglishDeutschFrançaisItalianoEspañolEnglish

E15

Selecting the item in the MENU screen

To select an item, start by moving the cursor ( ) to the desired item.

[Monitor]

1.Press the MENU button. Each time you press the button, the cursor moves down one item. If you press the button at the bottom, the cursor returns to the top. Example: Each time you press the MENU button in the TV MENU screen, the cursor moves in the following order: PICTURE → PROGRAMMES → AV CONNECTIONS → MODE SELECT → CHILD LOCK → PICTURE…

PICTURE PROGRAMMES AV CONNECTIONS MODE SELECT CHILD LOCK

[Remote control]

1.Press the buttons. Each time you press the button, the cursor moves up one item. Each time you press the button, the cursor moves down one item.

>> >> >> >> >>

TV/AV

E16

Adjusting the computer display (AUTO ADJUSTMENT)

When using the monitor as a computer display for the first time or after having changed the system settings during use, perform an automatic screen adjustment. “CLOCK”, “PHASE”, “H-POS”, and “V-POS” will be set to their optimum states.

INPUT

/BRIGHT

MAIN

POWER

BRIGHT MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

PC AV2AV1TV

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

1.Press the MAIN POWER button to turn on the monitor. When the power LED lights red, press the POWER button on the remote control.

2.Select the PC mode using the INPUT button (monitor) or the PC button (remote control). When using the INPUT button (monitor), each time you press it, the input changes in the following order: PC → Number (TV) → AV1 → AV2 → PC...

3.Turn on the computer, and then display an image that makes the entire screen display light colours (such as a light desktop background). If you are running Windows, you can use the Adjustment Pattern on the accompanying Utility Disk (see page E22).

4.Display the MENU screen using the MENU button. The cursor is positioned at “ADJUSTMENT”.

ADJUSTMENT GAIN CONTROL COLOUR CONTROL MODE SELECT PICTURE IN PICTURE

>> >> >> >> >>

<PC>

5.Press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The “ADJUSTMENT” screen will be displayed.

ADJUSTMENT

RETURN AUTO CLOCK PHASE H-POS V-POS RESET

[

127

[

200

[

]

<PC>

6.Press the OK/BRIGHT MODE button (monitor) or the OK button (remote control) to auto-adjust the settings. The screen will go dark and “ADJUSTING” will be displayed. After a few seconds, the “ADJUSTMENT” screen will return.

7.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

Notes:

- When you are using the 1280 x 768 or 1024 x 768 mode, specify the horizontal resolution of a 768-line screen in the MODE SELECT menu. (See page E25.)

- It may not be possible to achieve correct adjustment with the first automatic adjustment. In such a case, try repeating the automatic adjustment 2 or 3 times.

- If necessary due to any of the following, manual adjustments (page E22) can be performed after the automatic adjustment.

- When further fine adjustment is needed.

- When the computer’s video input signals are

Composite Sync or Sync on Green. (Automatic adjustments may not be possible.)

- When “OUT OF ADJUST” is displayed. (When

the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When making an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright.)

- Automatic adjustment may not be achieved correctly depending on what is displayed on the screen - moving pictures or the MS-DOS prompt etc.

EnglishDeutschFrançaisItalianoEspañolEnglish

E17

Common operations

Turning power on/off

INPUT

POWER

/BRIGHT

MAIN

POWER

BRIGHT

MODE

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

Turning power on

When the power LED is off:

1.Press the MAIN POWER button on the monitor.

2.Turn on power for the connected equipment. After a while the power LED will light green, and then the display mode will be displayed for several seconds.

When the power LED is lit red (standby):

1.Press the POWER button on the remote control.

2.Turn on power for the connected equipment. The power LED will light green, and then the display mode will be displayed for several seconds.

PC AV2AV1TV

MODE

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

Switching display modes (INPUT)

[Monitor]

1.Press the INPUT button. Each time you press the button, the input changes in the following order: PC → Number (TV) → AV1 → AV2 → PC...

P C

Display modes

PC PC mode Displays the computer’s

image.

Number TV mode Displays the TV’s image.

The number will be the channel being received.

AV1 AV1 mode Displays the image from

the equipment connected to the AV1 input.

AV2 AV2 mode Displays the image from

the equipment connected to the AV2 input.

[Remote control]

1.Press the PC, TV, AV1, or AV2 button. The monitor will switch to the display mode for the button you pressed.

Turning off power

1.Turn off power for the connected equipment.

2.Press the POWER button on the remote control. The power LED will light red (standby).

3.Press the MAIN POWER button on the monitor. The power LED will go out.

Notes:

- Always wait at least 5 seconds between switching power off/on. Rapid switching may damage the monitor or cause it to malfunction.

- After switching power on, it may take a little while before the screen displays an image.

- Do not turn off the power immediately after changing various settings on the screen. The changed values may not have been saved in the memory yet.

Notes:

- When you turn on the monitor, the initial display mode will be the mode being used when the monitor was last turned off.

- Using the

buttons or channel buttons on the remote control (0-9), or selecting channels using the programme table also automatically switches to TV mode, except for the following cases when in PC mode.

- When you are watching TV in the PIP window

(see page E20).

- When you are listening to TV (see page E21). In these cases, switch the display mode to TV using the INPUT button (monitor) or the TV button (remote control).

E18

Common operations

Adjusting the volume

The volume can be set individually for PC mode and TV/AV mode. Start by switching to the display mode for which you want to set the volume.

[Monitor]

1.Press the buttons.

<PC>

VOLUME 30 BRIGHT 31

2.Select “VOLUME” using the MENU button.

3.Adjust the volume using the buttons.

Increase Decrease

button button

The screen for adjusting the volume will automatically disappear after about 15 seconds.

[Remote control]

1.Press the

+/– buttons to adjust.

<PC>

VOLUME 30

Increase + button Decrease – button

The screen for adjusting the volume will automatically disappear after several seconds.

Adjusting the backlight

The brightness of the backlight can be set individually for PC mode and TV/AV mode. Start by switching to the display mode for which you want to adjust the backlight.

[Remote control]

1.Press the BRIGHT button.

<PC>

BRIGHT 31

2.Adjust the brightness using the buttons.

Increase button Decrease button

The screen for adjusting the brightness will automatically disappear after several seconds.

Selecting the language on the screen

You can select the language (English, German, Spanish, French or Italian) using the MODE SELECT menu while in any mode. (The selected language will be displayed in all modes.)

1.Display the MENU screen using the MENU button.

2.Select “MODE SELECT” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

3.Select “LANGUAGE” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Select the language you want to display using the

buttons (monitor) or the buttons

(remote control).

5.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

EnglishDeutschFrançaisItalianoEspañolEnglish

[Monitor]

1.Press the buttons.

<PC>

button button

VOLUME 30 BRIGHT 31

2.Select “BRIGHT” using the MENU button.

3.Adjust the brightness using the buttons.

Increase Decrease

The screen for adjusting the brightness will automatically disappear after about 15 seconds.

E19

Watching TV or other video in a window on the

computer screen (PICTURE IN PICTURE)

You can watch TV or other video in a small window (PIP window) on the computer screen.

INPUT

/BRIGHT

MAIN

POWER

BRIGHT

MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

PC AV2AV1TV

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

1.Select the PC mode using the INPUT button (monitor) or the PC button (remote control).

2.Press the PIP button (remote control). The small window will be displayed (the factory setting is TV picture).

To change channels in the small window, press the

buttons or the channel buttons (remote control), or use the programme table. (See page E34.) To adjust volume, see page E19. To close the small window, press the PIP button (remote control) again.

Selecting the video and audio sources

You can select the video source for the PIP window between TV, AV1 and AV2. You can also select the audio you want to hear while the PIP window is being displayed.

1.Display the MENU screen using the MENU button in PC mode.

2.Select “PICTURE IN PICTURE” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

3.Select “PIP INPUT” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Select the PIP image you want to view using the

buttons (monitor) or the buttons (remote

control).

5.Select “PIP SOUND” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

6.Select the audio you want to hear using the buttons (monitor) or the buttons (remote control). PC: Computer audio PIP: PIP window audio

7.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

Note:

- With the PICTURE IN PICTURE menu, you can do the following:

- Open/close the PIP window.

- Set the size/position of the PIP window. (See

page E25.)

- Set the video and audio sources of the PIP

window. (See right column.)

Note:

- To switch the audio reception mode for TV audio, press the SOUND button (remote control). (See page E35.)

E20

Listening to TV or another audio source while

viewing the computer screen

You can listen to TV or another audio source while the monitor is displaying the computer screen.

INPUT

BRIGHT

MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

PC AV2AV1TV

REVEAL

VIEW MODE

PIP

TEXT

BRIGHT

EnglishDeutschFrançaisItalianoEspañolEnglish

/BRIGHT

MAIN

POWER

DISPLAY

FREEZE

/HOLD

SOUND

1.Display the MENU screen using the MENU button in PC mode.

2.Select “MODE SELECT” using the MENU button (monitor) or the

buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

3.Select “SOUND” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Select the audio you want to hear using the

buttons (monitor) or the buttons (remote

control).

5.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

Notes:

- To switch the channel for TV audio, press the

buttons or the channel buttons (remote control), or use the programme table. (See page E34.)

- To switch the audio reception mode for TV audio, press the SOUND button (remote control). (See page E35.)

- This setting is disabled while a PIP window is displayed. The audio source (PIP SOUND) set in the PICTURE IN PICTURE menu takes precedence.

- When “STATUS” in the CHILD LOCK menu is “ALL” or “INDIVIDUAL” (see page E40), TV/AV-IN SOUND is not available in PC mode.

E21

Adjusting the display

You can adjust the colour of the computer screen image and make picture-in-picture settings using menus for the PC mode.

Adjustment Pattern

If you are using Windows, you can use the Adjustment Pattern on the accompanying CD-ROM. This explanation is for Windows 95/98/2000/Me/ XP, and assumes that the CD-ROM drive is “D” drive.

1.Load the accessory CD-ROM into the CD-ROM drive of the computer.

2.Open [My Computer] and select CD-ROM. If using Windows 3.1, open [File Manager] and choose “D” drive.

3.Double click on [Adj_uty.exe] to run the Adjustment Programme. The Adjustment Pattern will appear.

Adjustment Pattern

After completing the adjustments, press the computer’s [Esc] key to exit the Adjustment Programme.

Note:

- If your computer’s display mode is set to 65K colours, you may see the different colour levels in each colour pattern or the gray scale may look coloured. (This is due to the specification of the input signal and is not a malfunction.)

How to adjust

The following procedure describes the basic operation method. See pages E23 through E25 regarding individual items.

1.Select the PC mode using the INPUT button (monitor) or the PC button (remote control).

2.Display the MENU screen using the MENU button.

ADJUSTMENT GAIN CONTROL COLOUR CONTROL MODE SELECT PICTURE IN PICTURE

3.Select the menu you want to set using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Select the item you want to set using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

5.Change the numbers/values using the

buttons (monitor) or the buttons (remote control). You can continue to set other items. Do the following to return to the previous screen: (1) Select “RETURN” using the MENU button

(monitor) or the buttons (remote control).

(2) Press the OK/BRIGHT MODE button

(monitor) or the OK button (remote control).

6.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

>> >> >> >> >>

<PC>

Notes:

- If you do not press any buttons for about 30 seconds while in a menu screen, the settings you made up to that point will be applied and the screen will automatically disappear.

- This manual describes display adjustment based on the use of the Adjustment Pattern (for Windows).

E22

ADJUSTMENT menu

Adjusting the display

Item

AUTO

CLOCK

PHASE

H-POS, V-POS

Description

Automatically adjusts “CLOCK”, “PHASE”, “H-POS”, and “V-POS”. (See page E17.)

Adjusts the clock so that no vertical flicker noise is emitted.

Vertical flicker noise

Makes an adjustment after “CLOCK” is properly adjusted so that no horizontal flicker noise is emitted.

Horizontal flicker noise

Adjusts the position of the Adjustment Pattern so that it appears centred on screen.

Screen frame

Adjustment

Pattern

EnglishDeutschFrançaisItalianoEspañolEnglish

RESET

Resets adjustment values for this menu to their original factory settings.

E23

GAIN CONTROL menu

Adjusting the display

Item AUTO

BLACK LEVEL

CONTRAST

RESET

Notes about auto adjustment:

- If you are not using the Adjustment Pattern, it is necessary to have black area and white area of at least 5 mm x 5 mm on the screen. Adjustment may not be possible without those areas.

- If the signal coming from the computer is Composite Sync or Sync on Green, automatic adjustment may not be possible. Please perform manual adjustment instead.

- If “OUT OF ADJUST” is displayed, perform manual adjustment.

Description

Automatically adjusts “BLACK LEVEL” and “CONTRAST” based on brightest and darkest colours of the image displayed.

Adjusts screen brightness while you watch the colour pattern.

Colour pattern

Adjusts contrast so that all gradations appear while you watch the colour pattern.

Resets adjustment values for this menu to their original factory settings.

the

COLOUR CONTROL menu

Item COLOUR MODE

WHITE BALANCE

RESET

Description

Selects the colour tone.

...........

- STD

- sRGB

- VIVID Adjusts the colour temperature.

Set “WHITE BALANCE” to “STD” if you want to display all gradations.

- COOL2

- COOL1

...........

- STD

- WARM1

- WARM2

- USER

Resets adjustment values for this menu to their original factory settings.

Displays images using the original colour tone of the LCD monitor.

........

sRGB is an international standard for colour representation defined by the IEC (International Electrotechnical Commission). Colours are converted by taking into account the liquid crystal’s characteristics and thereby represent colour tone close to the original image.

........

Displays images in vivid primary colours.

.....

Colour tone bluer than standard.

.....

Colour tone slightly bluer than standard. Standard setting for colour tone.

....

Colour tone slightly redder than standard.

....

Colour tone redder than standard.

........

Allows you to individually adjust red, green, and blue contrast.

Note:

- “WHITE BALANCE” will be automatically set to “STD” when “COLOUR MODE” is set to “sRGB” or “VIVID”.

E24

MODE SELECT menu

Adjusting the display

Item VIEW MODE

768 LINES

SOUND

SCALING LANGUAGE

RESET

Description

Selects the screen size.

- NORMAL

- WIDE You can also set this item using the remote control. (See page E47.)

Specifies the horizontal resolution of a 768-line screen.

................

- 1024

................

- 1280

Selects the audio to listen to while displaying the computer screen. When displaying a PIP window, the audio set by “PIP SOUND” takes precedence. When “STATUS” in the CHILD LOCK menu is “ALL” or “INDIVIDUAL” (see page E40), TV/AV-IN SOUND is not available in PC mode.

Adjusts the image to optimum sharpness when it is enlarged. Selects the language (English, German, Spanish, French or Italian) on the

screen. (See page E19.) Resets adjustment values for this menu to their original factory settings.

PICTURE IN PICTURE menu

Item PIP DISPLAY

PIP SIZE PIP POSITION

PIP INPUT PIP SOUND

RESET

Description

Sets whether to display TV or other video source in a small window (PIP window) on the computer screen. You can also set this item using the remote control. (See page E20.)

Adjusts the size of the PIP window. Adjust the position of the PIP window.

To move up and down, use the (remote control). To move left and right, use the (remote control).

Selects the source of the PIP window. (See page E20.) Selects the audio you want to hear while displaying the PIP window.

....................

- PC

...................

- PIP

(See page E20.) Resets adjustment values for this menu to their original factory settings.

.........

...............

EnglishDeutschFrançaisItalianoEspañolEnglish

Expands the image to or near its aspect ratio. Expands the image so that it fills the screen.

1024 x 768 dot mode 1280 x 768 dot mode

buttons (monitor) or buttons

Computer audio PIP window audio

E25

Installing set-up information and the ICC profile (For Windows)

Depending on the type of computer or OS, you may need to install the monitor set-up information on your system. If so, follow the steps below to install the monitor set-up information. (Depending on the type of computer or OS, command names and methods may differ. Please follow the computer’s own operation manual while reading this.)

About the ICC profile

An ICC (International Color Consortium) profile is a file that describes the colour reproduction characteristics of the LCD monitor. Using an application compatible with an ICC profile, highly accurate colour reproduction can be realized.

- Windows 98/2000/Me/XP all use the ICC profile.

- When installing Windows 98/2000/Me/XP set-up information (described below), the ICC profile is also installed. If you would like to install the ICC profile only, please refer to Installing the ICC profile on page E28.

- When using the ICC profile, set “COLOUR MODE” and “WHITE BALANCE” to “STD”.

For Windows 95

Installing monitor set-up information into Windows 95. This explanation assumes that the CD-ROM drive is “D” drive.

1. Load the accessory CD-ROM into the CD-ROM

drive of the computer.

2. Click on the [Start] button. From [Settings],

choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced Properties], and

[Monitor], then [Change].

5. Click on [Have disk], confirm that [Copy

manufacturer’s files from:] is [D:] then click [OK].

6. Confirm that the monitor details are selected,

and click [OK].

7. Check that the monitor details are displayed,

then click [Apply].

8. Click [OK], and close the window.

For Windows 98

Installing monitor set-up information into Windows 98, and setting the monitor’s ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is “D” drive.

If the “Add New Hardware Wizard” has appeared:

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Click [Next].

3. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next].

4. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer’s files from:] is [D:], and click [OK].

5. Confirm that the monitor details are selected, then click [Next], [Next], and [Finish]. If the “Add New Hardware Wizard” appears, repeat the installation commands beginning from 2 above.

If the “Add New Hardware Wizard” has not appeared:

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Click on the [Start] button. From [Settings], choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change].

6. Click [Next].

7. Click on [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next].

8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer’s files from:] is [D:], and click [OK].

9. Confirm that the monitor details are selected, then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed, then click [Apply].

11. Click [OK], and close the window.

E26

Installing set-up information and the ICC profile (For Windows)

For Windows 2000

Installing monitor set-up information into Windows 2000, and setting the monitor’s ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is “D” drive.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Click on the [Start] button. From [Settings], choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. Click on [Properties], [Driver] and [Update Driver].

6. When [Upgrade Device Driver Wizard] appears, click [Next].

7. Check [Display a list of the known drivers for this device so that I can choose a specific driver] and click [Next].

8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer’s files from:] is [D:], and click [OK].

9. Select the monitor from the list displayed and click [Next].

10. Click [Next], confirm that the monitor’s name appears on the screen, and click [Finish]. If [The Digital Signature Not Found] appears, click [Yes].

11. Click on [Close].

12. Click [OK], and close the window.

For Windows Me

Installing monitor set-up information into Windows Me, and setting the monitor’s ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is “D” drive.

If the “Add New Hardware Wizard” has appeared:

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Check [Specify the location of the driver [Advanced]] and click [Next].

3. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.], then click [Next].

4. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer’s files from:] is [D:], and click [OK].

5. Select the monitor details from the list, then click [Next], [Next], and [Finish]. If the “Add New Hardware Wizard” appears, repeat the installation commands beginning from 2 above.

If the “Add New Hardware Wizard” has not appeared:

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Click on the [Start] button. From [Settings], choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings], [Advanced] and [Monitor].

5. In [Options], check [Automatically detect Plug & Play monitors] and click on [Change].

6. Check [Specify the location of the driver [Advanced]] and click [Next].

7. Check [Display a list of all the drivers in a specific location, so you can select the driver you want.] and click [Next].

8. When [Models] is displayed, click on [Have disk], confirm that [Copy manufacturer’s files from:] is [D:], and click [OK].

9. Select the monitor details, then click [Next], [Next], and [Finish].

10. Check that the monitor details are displayed, then click [Apply].

11. Click [OK], and close the window.

EnglishDeutschFrançaisItalianoEspañolEnglish

E27

Installing set-up information and the ICC profile (For Windows)

For Windows XP

Installing monitor set-up information into Windows XP, and setting the monitor’s ICC profile as a predetermined value. This explanation assumes that the CD-ROM drive is “D” drive.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Click on the [Start] button. Choose [Control Panel].

3. Switch to “Classic View”.

4. Double click on [Display].

5. Click on [Settings], [Advanced] and [Monitor].

6. Click on [Properties], [Driver] and [Update Driver].

7. When [Hardware Update Wizard] appears, check [Install from a list or specific location [Advanced]] and click [Next].

8. Check [Don’t search. I will choose the driver to install.] and click [Next].

9. Click on [Have Disk], confirm that [Copy manufacturer’s files from:] is [D:], and click [OK].

10. Select the monitor from the list displayed and click [Next]. If [has not passed Windows Logo testing...] appears, click [Continue Anyway].

11. Confirm that the monitor’s name appears on the screen.

12. Click on [Finish].

13. Click on [Close].

14. Click [OK], and close the window.

Installing the ICC profile

Installing the monitor’s ICC profile. (If the set-up information has already been installed, so too has the profile, and there is no need to install it.) This explanation assumes that the CD-ROM drive is “D” drive.

1. Load the accessory CD-ROM into the CD-ROM drive of the computer.

2. Click on the [Start] button. From [Settings], choose [Control Panel].

3. Double click on [Display].

4. Click on [Settings] and [Advanced].

5. Click on [General] and from [Compatibility] select [Apply the new display setting without restarting], then click on [Color Management].

6. Click [Add], and select CD-ROM as the file location.

7. Choose the colour profile that you would like to install, and click on [Add].

8. Choose the profile and click on [Set As Default].

9. Click [OK], and close the window.

- When using the ICC profile, set “COLOUR

MODE” and “WHITE BALANCE” to “STD”.

E28

Information about the ColorSync profile (For MacOS)

About the ColorSync profile

ColorSync is Apple Computer’s colour management system and enables colour reproduction characteristics to be realized when used with a compatible application. A ColorSync profile describes the colour characteristics of the LCD monitor.

Notes:

- This monitor’s ColorSync profile works with MacOS 8.5 or above.

- When using the ColorSync profile, set “COLOUR MODE” and “WHITE BALANCE” to “STD”.

Setting up the ColorSync profile

Notes:

- It is necessary to have PC Exchange or File Exchange installed in your system.

- Depending on the type of computer or OS, command names and methods may differ. Please follow the computer’s own operation manual while reading this.

1.Load the accessory CD-ROM into the CD-ROM drive of the computer.

2.Copy the profile to be used from the CD-ROM to the ColorSync profile folder in the system folder.

3.Using the ColorSync on the control panel, choose the profile to be used.

EnglishDeutschFrançaisItalianoEspañolEnglish

E29

Setting TV channels

Saving broadcast TV channels in the memory (AUTOMATIC SEARCH)

“AUTOMATIC SEARCH” allows you to search through available channels in your area. The tuner saves them to TV memory automatically.

Notes:

- Release the adjustment lock (see page E48) and cancel Child Lock (see page E41) if they have been set.

- Up to 100 channels (0-99) can be stored in TV memory.

INPUT

/BRIGHT

MAIN

POWER

BRIGHT MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

1.Turn on the monitor power.

2.Select the TV mode using the INPUT button (monitor) or the TV button (remote control).

3.Display the MENU screen using the MENU button.

PICTURE PROGRAMMES AV CONNECTIONS MODE SELECT CHILD LOCK

4.Select “PROGRAMMES” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

PROGRAMMES

RETURN

AUTOMATIC SEARCH MANUAL ADJUSTMENT SORT ERASE PROGRAMME RANGE ENTER/CHANGE NAME

PC AV2AV1TV

DISPLAY

>> >> >> >> >>

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

TV/AV

5.Select “AUTOMATIC SEARCH” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

AUTOMATIC SEARCH

RETURN COUNTRY COLOUR SYSTEM SOUND SYSTEM STORE PROGR. FROM START SEARCH

[

PAL

[

TV/AV

]

6.Select the desired adjustment item using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). Then select the desired item using the buttons (monitor) or the buttons (remote control).

Note:

- Select your country from the following: UK,

Germany, France, Italy or “OTHERS”. When “OTHERS” is selected, you can change “COLOUR SYSTEM” and “SOUND SYSTEM”.

7.Select “STORE PROGR. FROM” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

8.Select the programme position from which the programmes are to be stored using the buttons (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

9.Select “START SEARCH” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). When the search is completed, the new programmes found are displayed on the list.

Notes:

- To interrupt the automatic search or to exit the

list, press the INPUT button (monitor) or the MENU button (remote control).

- The programmes are named automatically

when an identification signal is sent. Or, they are named automatically from the table registered in the monitor memory.

- Programmes whose names could not be found

are displayed with “-----”. Names can be entered manually later. (See page E33.)

E30

Setting TV channels

Adjusting the individual settings of programmes (MANUAL ADJUSTMENT)

Using “MANUAL ADJUSTMENT”, you can adjust the individual settings of programmes.

Note:

- Release the adjustment lock (see page E48) and cancel Child Lock (see page E41) if they have been set.

INPUT

/BRIGHT

MAIN

POWER

BRIGHT MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

1.Display the “PROGRAMMES” screen by performing steps 1 to 4 of “Saving broadcast TV channels in the memory (AUTOMATIC SEARCH)” on page E30.

PC AV2AV1TV

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

2.Select “MANUAL ADJUSTMENT” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

MANUAL ADJUSTMENT

RETURN CHANNEL

FREQUENCY NAME COLOUR SYSTEM SOUND SYSTEM SKIP

TV/AV

[

]

[

048.25MHz

[

]

E02

[

]

PAL

[

]

[

]

OFF

]

3.Select the desired adjustment item using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). Then make the adjustment using the buttons (monitor) or the

buttons (remote control).

(See the table below for details.)

Notes:

- You can also use the channel buttons (0-9) on

the remote control to enter the frequency.

- To adjust “NAME”, first press the

OK/BRIGHT MODE button (monitor) or the OK button (remote control) to activate the text input mode. Then select the input position using the

buttons (monitor) or the buttons (remote control), and select the desired character using the buttons (monitor) or the buttons (remote control). When you finish, press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

Note:

- Depending on the settings in the colour system of the channels, switching between channels may be slow. If you want to speed up channel switching, switch “AUTO” in “COLOUR SYSTEM” to the current reception system (“PAL” or “SECAM”).

EnglishDeutschFrançaisItalianoEspañolEnglish

Item CHANNEL FREQUENCY

NAME COLOUR SYSTEM SOUND SYSTEM

SKIP

Choice/Value range

0-99

45.75-863.25 (MHz)

A-Z, 0-9, +, –, . , /, !, space AUTO, PAL, SECAM B/G, I, D/K, L

OFF

Description

The channel changes to the higher or lower channel. Receivable frequencies depending on TV norm,

installation site, and range. Programme name (up to five characters). Colour norm. TV norm. Channels with SKIP set to “ON” will be skipped when

you press the

buttons during TV viewing.

E31

Setting TV channels

Changing the programme positions (SORT)

The programme positions for individual programmes can be freely changed.

1.Display the “PROGRAMMES” screen by performing steps 1 to 4 of “Saving broadcast TV channels in the memory (AUTOMATIC SEARCH)” on page E30.

2.Select “SORT” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

SORT

00 05 10 15

01 E02 06 11 16 02 E03 07 12 17 03 E04 08 13 18 04 09 14 19

3.Select the desired programme using the

buttons (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). Move mode will be activated.

4.Select the desired position using the buttons (monitor) or the buttons (remote control) and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The selected programme will be moved to the selected position.

Note:

- When moving the programme, the buttons

(monitor) or the are not available.

5.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

buttons (remote control)

TV/AV

Erasing the programme range

The individual programme or programmes in a consecutive range can be erased.

1.Display the “PROGRAMMES” screen by performing steps 1 to 4 of “Saving broadcast TV channels in the memory (AUTOMATIC SEARCH)” on page E30.

2.Select “ERASE PROGRAMME RANGE” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

ERASE PROGRAMME RANGE

00 05 10 15

01 E02 06 11 16 02 E03 07 12 17 03 E04 08 13 18 04 09 14 19

3.Select the programme at the beginning of the desired range to be erased using the buttons (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Select the programme at the end of the range using the buttons (monitor) or the

buttons (remote control). When you want to select a single programme, skip this step.

5.Press the OK/BRIGHT MODE button (monitor) or the OK button (remote control) to erase the selected programme(s). All subsequent programmes move up.

6.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

TV/AV

E32

Setting TV channels

Enter/change the name of an individual programme

The name of an individual programme can be entered or changed.

1.Display the “PROGRAMMES” screen by performing steps 1 to 4 of “Saving broadcast TV channels in the memory (AUTOMATIC SEARCH)” on page E30.

2.Select “ENTER/CHANGE NAME” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

ENTER/CHANGE NAME

00 05 10 15

01 E02 06 11 16 02 E03 07 12 17 03 E04 08 13 18 04 09 14 19

3.Select the desired programme using the

buttons (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The character at the input position is highlighted.

4.Select the input position using the buttons (monitor) or the and select the desired character using the buttons (monitor) or the buttons (remote control).

5.Press the OK/BRIGHT MODE button (monitor) or the OK button (remote control) to accept the name entered.

6.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

buttons (remote control),

TV/AV

EnglishDeutschFrançaisItalianoEspañolEnglish

E33

Watching TV

Selecting the channels

This monitor allows you to select up to 100 channels (0-99).

INPUT

/BRIGHT

MAIN

POWER

BRIGHT MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

Using the channel buttons (remote control)

To select a 1-digit channel number (e.g., Channel 5):

Select the channel number using one of the following procedures.

- Press the 5 button and wait for approximately 3 seconds.

- Press the 0 button followed by the 5 button within 3 seconds.

To select a 2-digit channel number (e.g., Channel 12):

Press the 1 button followed by the 2 button within 3 seconds.

Using the

buttons (monitor/remote control)

- Press the button and the channel changes in the order shown below: 1 → 2 … → 98 → 99 → 0 → 1 → 2 → …

- Press the button and the channel changes in the order shown below: 2 → 1 → 0 → 99 → 98 … → 2 → 1 → 0 → …

PC AV2AV1TV

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

Selecting the channels using the programme table

The programme table shows a list of programmes in TV memory. They are located in channels 0 to

99. The currently selected programme is displayed in yellow and child-locked programmes which have not been cancelled are displayed in red.

1.Select the TV mode using the INPUT button (monitor) or the TV button (remote control).

2.Press the OK button (remote control). The programme table will be displayed.

Note:

- While the Teletext screen or the menu screen

is being displayed, you can not display the programme table by pressing the OK button (remote control).

PROGRAMME TABLE

00 05 10 15

01 E02 06 11 16 02 E03 07 12 17 03 E04 08 13 18 04 09 14 19

3.Select the desired programme using the

buttons (remote control). To display the previous or next list of the programme table:

- Press the

buttons (remote control) when the cursor is at a programme in the upper-left or low-right position.

- Press the

buttons (remote control) when the cursor is at a programme in the left or right column.

4.Display the selected programme using the OK button (remote control).

TV/AV

Notes:

- Pressing one of the above buttons or using the programme table (see right column) automatically switches to TV mode if the monitor is in PC or AV mode.

- Use the INPUT button (monitor) or the TV button (remote control) to switch the display mode to TV in the following cases when in PC mode.

- When you are watching TV in the PIP window

(see page E20).

- When you are listening to TV (see page E21).

- Channels set to be skipped cannot be displayed using the

buttons. (See page E31.)

- Channel “0” is reserved for RF output from a VCR.

E34

Watching TV

Selecting the audio reception mode

You can select the audio reception mode (stereo, bilingual or monaural) when you receive NICAM broadcasts and A2 stereo broadcasts as follows:

NICAM NICAM-B/G, I, D/K, L signal A2 stereo A2 stereo-B/G signal

EnglishDeutschFrançaisItalianoEspañolEnglish

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

DISPLAY

PC AV2AV1TV

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

1. Press the SOUND button on the remote control. The audio reception mode changes in the following order depending on the broadcast you are receiving.

NICAM broadcasts

Receiving a stereo broadcast

STEREO → MONO → STEREO ...

Receiving a bilingual broadcast

CH A → CH B → CH AB → MONO → CH A ...

Receiving a monaural broadcast

NICAM → MONO → NICAM ...

A2 stereo broadcasts

Receiving a stereo broadcast

STEREO → MONO → STEREO...

Receiving a bilingual broadcast

CH A → CH B → CH AB → CH A...

Receiving a monaural broadcast

MONO (fastened)

E35

Watching TV

Watching Teletext

Teletext is an information service organized like a magazine, which is provided by some TV stations in addition to regular television broadcasting. Your monitor receives Teletext signals broadcast by a TV station, processes the information and displays it graphically on the screen. News, weather and sports information, stock exchange prices, programme reviews and closed captioning (subtitle) are among the many services available through Teletext.

Notes:

- Operation in Teletext mode is described along with the remote control in this manual.

- Teletext is available only in TV/AV mode, not in PC mode (including when watching TV in PIP window).

Turning on and off the Teletext mode

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

DISPLAY

PC AV2AV1TV

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

1.Select a TV channel that is broadcasting the Teletext programme.

2.Press the TEXT button. The Teletext screen will be displayed.

3.Press the TEXT button again to turn off the Teletext mode.

Notes:

- If necessary, you can change the character set displayed on the Teletext screen. (See page E38.)

- The Teletext mode cannot be turned off or switched to other display modes with the input buttons.

E36

Watching TV

Selecting a Teletext page

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

DISPLAY

PC AV2AV1TV

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

Using the buttons

- To select the next page, press the button.

- To select the previous page, press the button.

Using the channel buttons

Enter the desired page number (100-899) using the channel buttons (0-9).

Notes:

- Page numbers beginning with 0 or 9 do not exist.

- If you enter the wrong numbers, simply complete the input of the 3-digit number and then enter the desired number again.

Returning to the page selected previously

Press the (flashback) button.

Note:

- The Teletext flashback memory is cleared when channels are changed after Teletext mode is switched to TV mode.

Selecting the TOP table

When TOP Teletext is being broadcast, you can display the TOP table by pressing the OK button. Select the desired subject in the table as follows:

- To move upwards, press the Red button.

- To move downwards, press the Cyan button.

- To select the highlighted item, press the Green button.

Note:

- The TOP (Table of Pages) system for Teletext is transmitted in Germany currently.

Selecting the Teletext index

When FLOF Teletext is being broadcast, you can display the index page (usually p.100) by pressing the OK button.

Note:

- The FLOF (Full Level One Features) system for Teletext is transmitted in UK currently.

EnglishDeutschFrançaisItalianoEspañolEnglish

Using the colour buttons

Select the desired subject using the colour buttons (Red/Green/Yellow/Cyan) corresponding to the coloured options at the bottom of Teletext screen. The configuration of the coloured options varies depending on the Teletext system.

E37

Watching TV

Selecting the subpages

When a selected Teletext page consists of several subpages, the desired subpages can be selected as follows:

1.Press the SUBPAGE button. “S****” is displayed in the left side of the header.

2.Enter a 4-digit number using the channel buttons (0-9) while this message is being displayed. The selected subpage is displayed.

Selecting the character set

1.Display the “CHARACTER SET” screen using the MENU button.

CHARACTER SET

PAN EUROPE FRENCH/ARABIC TURKISH/GREEK CYRILLIC

2.Select the desired character set using the buttons. The colour of the letters will turn to yellow. When selecting the character set, pressing the OK button will change the letters to red for an instant and then return them back to yellow.

3.Exit the screen using the MENU button.

Useful features for Teletext

To hold the current Teletext page

Press the FREEZE/HOLD button. You can stop updating the Teletext page. To cancel, press the FREEZE/HOLD button again.

To zoom the current Teletext page

Press the buttons. Each time the button is pressed, the current page is displayed as below.

ABC DEF

To quickly activate subtitles

Press the SUBTITLE button in TV/AV mode. Subtitles activate quickly. To cancel, press the TEXT button.

Note:

- You do not have to turn on the Teletext mode before pressing the SUBTITLE button.

To display the hidden information

Press the REVEAL button. You can display the hidden information such as solutions to riddles and puzzles. To cancel, press the REVEAL button again.

ABC DEF

E38

Watching TV

Using the Child Lock function

Important:

- Please refer to the end of this manual for “Disengaging Child Lock”.

The Child Lock function blocks the viewing of any channel for which Child Lock has been set, including the PIP window. When all programmes are locked, viewing video images in AV mode is also blocked. To use the Child Lock function, you first need to define your PIN (Personal Identification Number).

Defining a PIN

INPUT

/BRIGHT

BRIGHT

MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

PC AV2AV1TV

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

4.Input the desired 4-digit PIN (e.g. 1234) using the channel buttons (0-9) on the remote control.

Notes:

- Be sure to make a written note of your PIN.

- When you input the PIN for the first time, press

the OK button (remote control) to register it.

The “CHILD LOCK” screen will be displayed.

CHILD LOCK

RETURN STATUS INDIVIDUAL PROGRAMME RESET

[

OFF

TV/AV

]

5.Perform the next procedures or exit the screen using the MENU button (remote control).

EnglishDeutschFrançaisItalianoEspañolEnglish

MAIN

POWER

1.Select the TV mode using the INPUT button (monitor) or the TV button (remote control).

2.Display the MENU screen using the MENU button (remote control).

3.Select “CHILD LOCK” using the buttons (remote control), and press the OK button (remote control). The “PLEASE ENTER YOUR PIN” screen will be displayed.

E39

Watching TV

Setting Child Lock

Notes:

- To activate the Child Lock function, turn off the monitor and then turn it on again after finishing the settings.

- When “STATUS” in the CHILD LOCK menu is “ALL” or “INDIVIDUAL”, TV/AV-IN SOUND is not available in PC mode (see page E21).

To set Child Lock for all programmes

1.Display the “CHILD LOCK” screen by performing steps 1 to 4 of “Defining a PIN” on page E39.

2.Select “STATUS” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

3.Select “ALL” using the buttons (monitor) or the

buttons (remote control).

4.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

Note:

- This setting locks AV mode and TV function in all modes.

To set Child Lock for individual programmes

1.Display the “CHILD LOCK” screen by performing steps 1 to 4 of “Defining a PIN” on page E39.

2.Select “STATUS” using the MENU button (monitor) or the and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

3.Select “INDIVIDUAL” using the buttons (monitor) or the

4.Select “INDIVIDUAL PROGRAMME” using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The “INDIVIDUAL PROGRAMME” screen will be displayed.

5.Select the desired programme using the

buttons (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control). The locked programme is displayed in red.

Note:

- To unlock the programme, perform the step 5

again.

6.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

Notes:

- Even when Child Lock is activated, unlocked programmes can be viewed, but the PROGRAMMES menu cannot be selected on the TV MENU screen. To adjust the PROGRAMMES menu, you need to cancel the Child Lock setting temporarily. (See page E41.)

- When Child Lock is activated individually, if you try to select the programme and the PIN input screen appears, you can use the buttons to find other unlocked programmes.

buttons (remote control),

buttons (remote control).

E40

Watching TV

Temporarily cancelling the Child Lock setting

By temporarily cancelling the Child Lock setting, you can view the programmes for which the Child Lock has been set.

If you are currently at the PIN input screen, input your PIN using the channel buttons (0-9) on the remote control. When the PIN is correctly entered, the normal screen is displayed.

If you are not currently at the PIN input screen, perform steps 1 to 3 of “Defining a PIN” on page E39, and input your PIN.

Notes:

- When the PIN input screen appears for the locked programme in the PIP window, closing the PIP window using the PIP button (remote control) enables you to operate the monitor in PC mode.

- When the power is turned off and on after the Child Lock is cancelled, the Child Lock becomes effective again.

- Unless the Child Lock is cancelled within approximately 20 seconds, the monitor goes to the standby mode.

EnglishDeutschFrançaisItalianoEspañolEnglish

E41

Enjoying DVDs, games, and other equipment

You can enjoy two additional pieces of AV equipment connected to your monitor such as VCRs, DVD players, and game systems. (See pages E12 and E13.)

Equipment connected to AV-IN1:

Equipment connected to AV-IN2:

Display mode “AV1”

Display mode “AV2”

Note:

- Since the use of AV1 and AV2 is the same, this manual refers to AV1 mode and AV2 mode as “AV mode”.

INPUT

/BRIGHT

MAIN

POWER

BRIGHT MODE

POWER

SUBPAGE SUBTITLE

SLEEP MENU

BRIGHT

MODE

PC AV2AV1TV

DISPLAY

REVEAL

FREEZE

/HOLD

VIEW MODE

SOUND

PIP

TEXT

BRIGHT

1.Make adjustments for connections with external devices on the “AV CONNECTIONS” screen. (See page E45.)

2.Switch the display mode to AV1 or AV2. See page E18 for more information.

AV1

RGB

3.Turn on the connected AV equipment, and then play a tape, DVD, or game.

4.Adjust the volume. See page E19 for more information.

Notes:

- Sometimes no image will be displayed during fast searching of video.

- The display may flicker during slow playback of video depending on the VCR or videotape you are using.

- You cannot play shooting games that use gun controllers with this monitor.

E42

Handy features (for TV/AV mode)

Pausing the screen (FREEZE)

This feature pauses the image from the TV or other connected AV equipment. This is handy when you want to write down a recipe or the address for a prize contest. Perform this operation using the remote control.

1.Press the FREEZE/HOLD button. The images will pause.

Cancelling pausing

1.Press the FREEZE/HOLD button again.

Notes:

- You cannot pause the TV or video image in the picture-in-picture window.

- Changing channels or switching the display mode (input) automatically cancels pausing.

Returning to previous channel (FLASHBACK)

You can return to the previous channel you were watching. Perform this procedure with remote control.

Switching power off after a specified length of time (SLEEP)

The monitor can automatically switch off (standby) after a specified length of time. This is handy if you want to watch the monitor at bedtime. Perform this operation using the remote control.

1.Press the SLEEP button.

2.Specify in how many minutes you want the monitor to switch off by pressing the SLEEP button. The time changes in the following order each time you press the button: 30 min → 60 min → 90 min → 120 min → 150 min → --- min → 30 min

When the specified time elapses, the monitor automatically switches off and clears the SLEEP timer.

Checking the time remaining on the SLEEP timer

1.Press the DISPLAY button. The time remaining on the SLEEP timer will be displayed for several seconds. You can also check the time remaining by pressing the SLEEP button once.

EnglishDeutschFrançaisItalianoEspañolEnglish

1.Press the The monitor will return to the channel you were previously watching.

button.

Changing the specified time

1.Press the SLEEP button. The remaining time will be displayed.

2.Change the specified time by pressing the SLEEP button several times as needed.

Notes:

- When there are only 5 minutes remaining on the SLEEP timer, the remaining time will be displayed every minute.

- Pressing the POWER button while the SLEEP timer is operating will clear the timer.

- Switching to PC mode automatically clears the SLEEP timer.

- You can also set the SLEEP timer from the MODE SELECT menu. (See page E46.)

E43

Adjusting the display

You can adjust TV and video images and perform various settings using menus for the TV/AV mode.

- All the menus except for the PROGRAMMES menu are common for TV and AV modes. All the values set in TV mode will be also applied in AV mode.

How to adjust

The following procedure describes the basic operation method. See pages E45 and E46 regarding individual items.

1.Select the TV mode or AV mode. See page E18 for more information.

2.Display the MENU screen using the MENU button.

TV/AV

PICTURE PROGRAMMES AV CONNECTIONS MODE SELECT CHILD LOCK

3.Select the menu you want to set using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

4.Select the item you want to set using the MENU button (monitor) or the buttons (remote control), and press the OK/BRIGHT MODE button (monitor) or the OK button (remote control).

5.Change the numbers/values using the

buttons (monitor) or the buttons (remote control). You can continue to set other items. Do the following to return to the previous screen: (1) Select “RETURN” using the MENU button

(monitor) or the buttons (remote control).

(2) Press the OK/BRIGHT MODE button

(monitor) or the OK button (remote control).

6.Exit the screen using the INPUT button (monitor) or the MENU button (remote control).

>> >> >> >> >>

Note:

- If you do not press any buttons for about 30 seconds while in a menu screen, the settings you made up to that point will be applied and the screen will automatically disappear.

E44

PICTURE menu

Adjusting the display

Item CONTRAST BLACK LEVEL COLOUR TINT SHARPNESS WHITE BALANCE

RESET

Description

Adjusts contrast. Adjusts the overall brightness of the screen. Adjusts the colour depth. Adjusts the colour tone. Adjusts the image quality. Adjusts the colour temperature.

.................

- STD

- WARM Resets adjustment values for this menu to their original factory settings.

.............

Standard setting for colour tone. Colour tone redder than standard.

PROGRAMMES menu (TV mode only)

Item AUTOMATIC SEARCH MANUAL ADJUSTMENT SORT ERASE PROGRAMME

RANGE

ENTER/CHANGE NAME

Description

Sets available programmes automatically. (See page E30.) Adjusts programmes manually. (See page E31.) Changes the programme positions freely. (See page E32.) Erases the individual programme or programmes in a consecutive range.

(See page E32.) Enters or changes the name of an individual programme. (See page E33.)

EnglishDeutschFrançaisItalianoEspañolEnglish

AV CONNECTIONS menu

Item AV1 SIGNAL TYPE

AV1 COLOUR SYSTEM

AV1 CONTROL VOLTAGE

AV2 COLOUR SYSTEM

RESET

Notes:

- When a normal picture is not displayed, change the signal type and/or colour system.

- Switching between AV input signals may be slow, depending on the settings in “COLOUR SYSTEM”. If you want to speed up signal switching, switch “AUTO” in “COLOUR SYSTEM” to the current reception colour system.

Description

Selects the signal type of the external equipment connected to AV-IN1.

- AUTO

- CVBS

- Y/C Selects the colour system of the external equipment connected to AV-IN1

PAL/SECAM/N358(NTSC 3.58)/N443(NTSC 4.43)/PAL60/PAL-M/PAL-N Sets whether to temporarily output the image and sound of AV-IN1 in TV

mode.

- OFF

- ON Selects the colour system of the external equipment connected to AV-IN2:

PAL/SECAM/N358(NTSC 3.58)/N443(NTSC 4.43)/PAL60/PAL-M/PAL-N. Resets adjustment values for this menu to their original factory settings.

..............

..................

.................

..................

Original factory setting. Composite video signal. S-video signal.

Original factory setting. Responds to the signal from AV-IN1 in TV mode.

E45

MODE SELECT menu

Adjusting the display

Item VIEW MODE

SLEEP TIMER

LANGUAGE

RESET

CHILD LOCK menu

Item STATUS

INDIVIDUAL PROGRAMME

RESET

Description

Selects the screen size.

- NORMAL

- WIDE

- ZOOM1

- ZOOM2 You can also set this item using the remote control. (See page E47.) When you select “ZOOM1” or “ZOOM2”, the top and bottom of the screen will be cut off slightly.

Specifies how many minutes until the monitor switches off (standby). This can also be set using the remote control. (See page E43.)

Selects the language (English, German, Spanish, French or Italian) on the screen. (See page E19.)

Resets adjustment values for this menu to their original factory settings.

Description

Sets unlock or lock for all programmes, or sets an individual programme lock. (See page E40.)

- OFF

- ALL

- INDIVIDUAL When “STATUS” in the CHILD LOCK menu is “ALL” or “INDIVIDUAL”, TV/AV-IN SOUND is not available in PC mode (see page E21).

Selects the programme to be locked when “INDIVIDUAL” is selected for “STATUS”. (See page E40.)

Resets adjustment values for this menu to their original factory settings. However, the PIN you have set is not cleared. Concerning the PIN, refer to the end of this manual for “Disengaging Child Lock”.

........

..............

...........

.................

Displays the screen at 4:3. Displays the screen at 16:9. Enlarges and displays the entire screen, but with a smaller screen size than “ZOOM2”. Please use this mode when captions or telops at the top or bottom of the screen are cut off. Enlarges and displays the entire screen at 4:3.

Original factory setting. Locks all TV programmes and video images in AV mode.

...

Locks the specified TV programmes only.

E46

Other features

Checking the current channel and audio reception mode on screen (DISPLAY)

You can check the current display mode, channel being received, audio reception mode, and time remaining on the SLEEP timer. Perform this operation using the remote control.

1.Press the DISPLAY button. Various information about the current state will be displayed. The information will disappear after several seconds.

Notes:

- The information displayed will vary depending on the current display mode and other settings.

- If the broadcast changes in TV mode while the information is displaying, the broadcast and the audio reception mode may not match.

Changing BRIGHT MODE

You can lower energy consumption by decreasing screen brightness.

Muting the sound (MUTE)

This feature is handy when you want to mute the sound such as when the phone rings or someone comes to the door. Perform this operation using the remote control.

1.Press the The sound will be muted and “MUTE” will be displayed. “MUTE” will disappear after several seconds.

button.

Cancelling muting

1.Press the button again, or press any other buttons.

Changing the screen size (VIEW MODE)

You can change the screen size to match the video on videotapes and DVDs. Perform this operation using the remote control.

1.Press the VIEW MODE button. The mode switches in the following order each time you press the button:

EnglishDeutschFrançaisItalianoEspañolEnglish

1.Press the OK/BRIGHT MODE button (monitor) or the BRIGHT MODE button (remote control). The mode switches in the following order each time you press the button:

[PC mode]

DARK (power save) → BRIGHT → DARK (power save)...

[TV/AV mode]

NORMAL (power save 1) → DARK (power save 2) → BRIGHT → NORMAL (power save 1)...

[PC mode]

NORMAL → WIDE → NORMAL...

NORMAL: Expands the image to or near its aspect ratio. WIDE: Expands the image so that it fills the screen.

[TV/AV mode]

NORMAL → WIDE → ZOOM1 → ZOOM2 → NORMAL...

NORMAL: Displays the screen at 4:3. WIDE: Displays the screen at 16:9. ZOOM1: Enlarges and displays the entire

screen, but with a smaller screen size than “ZOOM2”. Please use this mode when captions or telops at the top or bottom of the screen are cut off.

ZOOM2:

Notes:

- When you select “ZOOM1” or “ZOOM2” in TV/AV mode, the top and bottom of the screen will be cut off slightly.

- You can set this item individually for PC mode and TV/AV mode in the MODE SELECT menu. (See pages E25 and E46.)

Enlarges and displays the entire screen at 4:3.

E47

Other features

Preventing changes to adjusted values (ADJUSTMENT LOCK)

Disabling the control buttons other than the following buttons (monitor and remote control) prevents adjusted values from being changed. The changing of adjusted values for not only PC mode, but for TV/AV mode as well will be prevented.

[Monitor]

- MAIN POWER button

- buttons

- INPUT button

- buttons

[Remote control]

- POWER button

- + – buttons

- button

- Input buttons (PC, TV, AV1, and AV2)

- buttons

- Channel buttons (0-9)

- OK button

- TEXT button

- SUBTITLE button

- FREEZE/HOLD button button

Resetting all adjustment values (ALL RESET)

All adjustment values will be reset. This includes not only PC mode, but also TV/AV mode (including channel settings, etc.). Concerning the ALL RESET procedure, refer to the end of this manual.

Perform this procedure on the monitor.

1.Turn off the monitor power using the MAIN

POWER button.

2.While pressing the MENU button, press the

MAIN POWER button (i.e. turn the power on). Continue to press the buttons until “ADJUSTMENT LOCKED” appears on the screen. The lock is set when the message is displayed.

Releasing the adjustment lock

Perform this procedure on the monitor.

1.Turn off the monitor power using the MAIN

POWER button.

2.While pressing the MENU button, press the

MAIN POWER button (i.e. turn the power on). Continue to press the buttons until “ADJUSTMENT UNLOCKED” appears on the screen. The lock is released when the message is displayed.

CAUTION!

- When the adjustment lock is set, all buttons on

the monitor and remote control other than the above buttons are disabled. To use buttons other than the above buttons, release the adjustment lock.

E48

Instructions for attaching a VESA-compliant mount

An arm or stand based on the VESA standard (commercially available) can be attached to the monitor. Procurement of the arm or stand is at the customer’s discretion.

Arms or stands able to be used

Attachments must satisfy the following.

- Compatible with the VESA standard.

- Have a gap of 100 mm x 100 mm between the

screw holes on the section to be attached.

- Not be likely to fall off or break off after being

attached to the monitor.

How to attach the arm or stand

- Be careful not to over bend the cable or add

extension cords as this could lead to malfunction.

- While following these instructions, please also

refer to the installation instructions in the operation manual included with the arm or stand.

CAUTION!

- Be careful not to get your fingers pinched

between the display and stand nor to let the stand drop. These could lead to injury.

1. Remove the cables.

2.Spread out a soft cloth on a suitable horizontal

surface. Being careful not to damage the monitor, gently lay the monitor on it display-side down.

3.Remove the four screws and then remove the

stand from the monitor.

Notes:

- The stand is specially made for use with this monitor. Once having removed the stand, never attempt to attach it to another equipment.

- Once having removed the screws, store them together with the stand and if the stand is ever re-attached be sure to use the original screws. Using different screws could lead to a malfunction.

4. Attach the arm to the monitor with the four screws.

Note:

- The screws used to attach the arm should be M4 screws with a length of 10-12 mm protruding from the surface to be attached. Using different screws could cause the monitor to fall off or to be internally damaged.

10-12 mm

Screw used to attach arm

Arm Part of monitor to which arm is

attached

EnglishDeutschFrançaisItalianoEspañolEnglish

E49

Monitor care

Troubleshooting

If you think the monitor may be faulty, please check the following points before taking it to be repaired. If afterwards it still does not work, please contact the shop where you purchased the monitor or your nearest Sharp authorized Service Centre.

The monitor’s fluorescent tubes have a limited life span.

- If the screen darkens, persistently flickers or does not light up, the fluorescent tube has reached the end of its operational life span. Please inquire at the shop where you purchased the monitor or your nearest Sharp authorized Service Centre.

- In the initial period of use, due to the characteristics of fluorescent tubes the screen may flicker. (This is not a malfunction.) Should this happen, check by first turning off the power, then turning it on again.

Problem

There is no picture. (Power LED does not light.)

There is no picture. (Power LED is lit orange.)

The image appears distorted.

The remote control does not work.

There is no TV picture.

A particular channel will not tune in. There are stripes or dots on

TV picture. The picture wavers.

The TV picture is doubled.

There are colour bands.

The TV picture is distorted.

There is no video picture. There is no game picture.

What to Check

- Are the AC adapter and power cord properly connected? (Page E14)

- Is power turned on? (Page E18)

- Is the monitor properly connected to the computer? (Page E10)

- Is the computer turned on?

- Does the computer’s signal timing correspond to monitor specifications? (Page E53)

- Is the computer in power-saving mode?

Try pressing a key on the keyboard or moving the mouse.

- Does the computer’s signal timing correspond to monitor specifications? (Page E53)

- Perform automatic adjustment. (Page E17)

- Change the Vsync frequency (refresh rate) on the computer you are using to a low value if possible. (Page E53)

- Have the batteries of the remote control run out? (Page E9)

- Are the batteries placed in the right direction in the remote control? (Page E9)

- Is the adjustment lock on? (Page E48)

- Is the monitor connected to an antenna? Check the connection. (Page E11)

- Is the monitor switched to TV mode? (Page E18)

- Have you set TV channels properly? (Pages E30 to E33)

- Is there interference from automobiles, trains, neon signs, computers, or other sources?

- Place the antenna as far as possible away from potential sources of interference.

- Place the antenna line as far as possible from the computer.

- Is the antenna is facing the right direction?

- There may be reflected electric waves from nearby mountains or buildings. Try changing the antenna’s height and direction.

- Is there interference from a nearby TV? Changing the antenna’s height and direction may help.

- Try switching power off, waiting several seconds, and then turning power back on.

- Are the cables properly connected? (Pages E12 and E13)

- Have you switched to AV mode? (Page E18)

- Have you turned on the connected equipment?

- Change the signal type and/or colour system. (Page E45)

E50

Monitor care

Problem

The TV picture does not move. The video picture does not move.

I have forgotten my PIN (Personal Identification Number).

There is no sound.

Control buttons do not work. The MENU screen does not appear.

“PROGRAMMES” in the MENU screen for TV mode cannot be selected.

Monitor care

What to Check

- Is the screen pausing? Did you press the FREEZE/HOLD button? (Page E43)

- See “Disengaging Child Lock” at the end of this manual.

- Are the audio cables properly connected? (Pages E10, E12 and E13)

- Did you press the

- No sound can be heard from the monitor’s speakers while headphones are connected.

- Adjust the volume. (Page E19)

- No sound can be heard from the monitor’s speakers while the monitor is in power-saving mode.

- When “STATUS” in the CHILD LOCK menu is “ALL” or “INDIVIDUAL”, TV/AV-IN SOUND is not available in PC mode. (Pages E21 and E40)

- In AV mode, sound cannot be heard if there is no video input signal.

- Is the adjustment lock set? (Page E48)

- Is Child Lock set? Cancel the lock temporarily. (Page E41)

- Is the monitor switched to TV mode? (Page E18)

button? (Page E47)

EnglishDeutschFrançaisItalianoEspañolEnglish

Always remove the plug from the AC outlet when cleaning the monitor.

Cabinet and control panel section

Use a soft dry cloth to lightly wipe away any grime from the cabinet and control panel. If they are very dirty, apply neutral detergent to a dampened soft cloth, wring it out well and wipe away grime.

LCD panel section

Use a soft dry cloth to lightly wipe away dirt and dust from the surface of the LCD panel. (A soft cloth such as gauze or that used for lens cleaning is suitable.)

CAUTION!

- Never use thinner, benzine, alcohol, glass cleaner, etc., as this could lead to colour change or change in shape.

- Never scratch the monitor with anything hard or apply strong pressure as this could leave marks or result in malfunction.

Storage

If the monitor will not be used for a long period of time, be sure to remove the power plug from the AC outlet.

CAUTION!

- Do not leave the monitor in contact with rubber or plastic items for long periods of time as this could lead to colour change or change in shape.

E51

Specifications

Product specifications

Model name

LL-171ME

LCD display

43 cm measured diagonally TFT LCD module

Resolution (max.)

WXGA 1280 x 768 pixels

Displayable colours (max.)

Approx. 16.19 million colours (6 bit + FRC)

Dot pitch

0.289 (H) x 0.289 (V) mm

Brightness (max.)

260 cd/m2 (PC mode); 400 cd/m2 (when “WHITE BALANCE” is set to “WARM” in TV/AV mode)

Contrast ratio

600:1

Angle of visibility

Left-right 170°; up-down 170° (contrast ratio

Screen display size

369.6 (H) x 221.76 (V) mm

Video signal

Analog RGB (0.7 Vp-p) [75Ω]

Sync signal

Separate Sync (TTL level: +/-), Sync on Green, Composite Sync (TTL level: +/-)

Video colour system

PAL/SECAM/NTSC

TV-standard

B/G, I, D/K, L

Stereo/bilingual

NICAM, A2 stereo

Expansion compensation

Digital scaling (Enlarges VGA/SVGA/XGA etc. to full screen size.) [Enlarged display (full screen, Fixed aspect ratio)]

- 1:1 display is not possible.

Plug & Play

VESA DDC1/DDC2B compatible

Power management

VESA: based on DPMS

Speaker output

2.7 W + 2.7 W

Input terminals

Computer signal: Mini D-sub15 pin (3 rows) x 1 Computer audio: Mini stereo jack (φ 3.5 mm) x 1 Antenna (DIN): x 1 21-pin Euro-SCART (RGB) terminal x 1 Video image: RCA pin x 1 S-video image: x 1 Audio input terminal: RCA pin (L/R x 1)

Headphone terminal

Mini stereo jack (φ 3.5 mm)

Screen tilt

Upward approx. 0-20°; downward approx. 0-5°

> =

10)

Power supply

AC 110-240 V, 50/60 Hz (Uses special AC adapter, type NL-A69J of Sharp Corporation)

Temperature of operating environment

5-35°C

Power consumption

60 W; 2.2 W in standby; 2.2 W in power-saving mode (Uses special AC adapter)

Dimensions

Approx. 432 (W) x 184 (D) x 373 (H) mm

Weight

Approx. 5.9 kg (excluding signal cable and AC adapter) Approx. 5.0 kg (excluding stand)

Dimensions (Units: mm)

432

373

326

265

- PC analog signal cable: approx. 1.8 m

- PC audio cable: approx. 1.8 m

- Special AC adapter:

Approx. 1.5 m

Approx. 150 (W) x 60 (D) x 35 (H) mm

Note:

- As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

184

E52

Specifications

Relevant signal timings (PC mode)

Display mode

VESA

WXGA

US text

Power Macintosh series

Hsync

Vsync

Dot frequency

- Recommended resolution is 1280 x 768 or 1024 x 768.

- All are compliant only with non-interlaced.

- Frequencies for Power Macintosh are reference values. To connect, another adapter (commercially available) may be required.

- If the monitor is receiving timing signals that are not compatible, “OUT OF TIMING” will appear. Follow your computer’s instruction manual to set the timing so that it is compatible with the monitor.

- If the monitor is not receiving any signal (synch signal), “NO SIGNAL” will appear.

The analog RGB input connector pin

(Mini D-sub connector with 15 pins)

21-pin Euro-SCART terminal (RGB)

No. Function

Audio right output

Audio right input

Audio left output

Common earth for audio

Earth for blue

Audio left input

BLUE input

Audio-video control

Earth for green

Not used

GREEN input

Not used

Earth for red

Not used

RED input/Chroma S-video input

RED/GREEN/BLUE control

Earth for video

Earth for RED/GREEN/BLUE control

Video output

Video input (PAL/SECAM/NTSC)/S-video input

Plug shield

EnglishDeutschFrançaisItalianoEspañolEnglish

No. Function

1 Red video signal input

2 Green video signal input

3 Blue video signal input

4 GND

5 GND

6 For red video signal GND

7 For green video signal GND

8 For blue video signal GND

9 +5V

10 GND

11 N.C.

12 DDC data

13 For Hsync signal input

14 For Vsync signal input

15 DDC clock

E53

Specifications

Power management

The monitor is based on VESA DPMS (Display Power Management Signalling). To activate the monitor’s power management function, both the video card and the computer must conform to the VESA DPMS standard.

DPMS mode Screen

ON Display on 60 W Yes Yes

STANDBY No Yes

SUSPEND Display off 2.2 W Yes No

OFF No No

Power

consumption

H-sync V-sync

DDC (Plug & Play)

This monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for carrying out Plug & Play functions on the monitor or computer. It transfers information such as degree of resolution between the monitor and computer. You can use this function if your computer is DDC compliant and if it is set so that it can detect the Plug & Play monitor. There are many varieties of DDC due to the differences between systems. This monitor works with DDC1 and DDC2B.

E54

Sharp LL-171ME OPERATION MANUAL

Specifications and Main Features

Frequently Asked Questions

User Manual