Page 1
15” LCD Color Monitor Sharp LL-153A
1
Service
Service
Service
Horizontal Frequency
30kHz –80kHz
TABLE OF CONTENTS
Description
Page Description Page
N
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
Table Of Contents.......……..……..........................…........1
Revision List.….............……..........................……......2
Important Safety Notice.…………....................……......3
1. Monitor Specification..............................………........4
2. LCD Monitor Description…………………………….......5
3. Operation Instruction…………...............……...........6
3.1 General Instructions...........................…...........6
3.2 Control Button…………….…..............……...............6
3.3 Adjusting the Picture...........................…............7
4. Input/Output Specification............………..……............8
4.1 Input Signal Connector............………….................8
4.2 Factory Preset Display Modes..........................9
4.3 Power Supply……..………………………….………….10
4.4 Panel Specification.....………………………................10
5. Block Diagram……...................…………................13
5.1 Soft Flow Chart….………………..……..……....….......13
5.2 Electrical Block Diagram….……………..…........….….15
6. Schematic……………....................................…17
6.1 Main Board.……...……..........................................17
6.2 Inverter Board..………..……..................................22
6.3 Adapter Board...………..…….................................23
6.4 Audio Board...………....…….................................24
7. PCB Layout..…….………….......................................25
7.1 Main Board…………….........................................25
7.2 PWPC Board…..………....................................26
7.3 Audio Board……….……….....................................27
7.4 Key Board……………….....................................28
8. Maintainability……….......................................28
8.1 Equipments and Tools Requirement……..............28
8.2 Trouble Shooting…….………..............................29
9. White-Balance, Luminance adjustment.............34
10. Monitor Exploded View……….……………............36
11. BOM List……….....................................................37
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Page 2
15” LCD Color Monitor Sharp LL-153A
2
Revision List
Revision Date Revision History TPV Model
A00 Dec-28-06 Initial Release T56CM5NJXXXWAJ
Page 3
15” LCD Color Monitor Sharp LL-153A
3
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)
Page 4
15” LCD Color Monitor Sharp LL-153A
4
1. Monitor Specifications
Items Descriptions
Driving system TFT Color LCD
Type CPT CLAA150XP01Q
Size 38cm(15.0")
Pixel pitch 0.297mm(H) x 0.297mm(V)
Viewable angle 140˚ (H) 125˚ (V)
LCD Panel
Response time (type) 8 ms for CPT panel
Video
R, G, B Analog input
Digital input
Sync. Type H/V TTL
H-Frequency 24.8kHz – 80kHz
Input
V-Frequency 56-75Hz
ON Mode
≤27W
Power Consumption
OFF Mode
≤1W
Contrast Ratio 500:1
Dot Clock 135MHz
White Luminance 250cd/m
2
Max. Resolution 1024 × 768 @75Hz
Power Consumption
(Maximum)
27 Watts
Display Color 16 M (6-bits+FRC)
Plug & Play VESA DDC2BTM
Input Connector 15-pin D-Sub
Maximum Screen Size Horizontal: 304.1mm;Vertical: 228.1mm
Power Source 100~240VAC,47~63Hz
Environmental
Considerations
Operating Temp: 5°C to 35°C
Storage Temp: -20°C to 60°C
Operating Humidity: 10% to 85%
Page 5
15” LCD Color Monitor Sharp LL-153A
5
2. LCD Monitor Description
The LCD MONITOR will contain a main board, a power board and a keypad board which house the flat panel control
logic, brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
AC-IN
100V-240V
PWPC board
(
Include: adapter, inverter)
Flat Panel and
CCFL backlight
main board
RS232 Connector
For white balance
adjustment in factory
mode
HOST Computer
CCFL Drive.
Video signal, DDC
Monitor Block Diagram
Keyboard
Page 6
15” LCD Color Monitor Sharp LL-153A
6
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will light up.
3.2 Control Buttons
- Power Button:
When pressed, the monitor enters the off mode, and the LED turns blank. Press again to restore normal status.
- Left / Right Button:
The Left/Right Button is used to control the monitor functions. Press to switch functions or adjust settings.
- /MODE:
The
/MODE Key is used to move the cursor and select display mode.
- Power Indicator:
Green — Power On mode.
Red — Power Saving mode.
Blank —Power Off Mode.
LED = GREEN, BLINKING (0.5s period) —Out of Range
NO. Name
Within OSD
Without OSD
1 MENU
An adjustment menu display, a change,
elimination
Activate OSD main menu
2
/MODE
Move the
cursor to down
Select display mode to STD or
OFFICE or sRGB or VIVID.
3
<
1.Move the cursor to left
2. Decrease the value of the selected item
Activate the volume and the bright
menu
4
>
1.Move the cursor to right
2.Increase the value of the selected item
Activate the volume and the
brightness menu
5 POWER Power On / Off Power On / Off
6 Indicator Light Green—On Red—Save Green—On Red—Save
Power On/Off
Move the Cursor and
Select Dis
play
Mode
Volume/Bright +, & Menu Select
OSD Menu
Indicator Light
Page 7
15” LCD Color Monitor Sharp LL-153A
7
3.3 Adjusting the Picture
1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the
/ MODE -button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function, or leave the monitor alone for 10 seconds. If you want to adjust any
other function, repeat steps 2-4.
CONTROL FUNCTION
Main Menu Sub Main Menu Description
Clock
Adjust picture Clock to reduce
Vertical-Line noise.
Phase
Adjust Picture Phase to reduce
Horizontal-Line noise.
H. Position
Adjust the horizontal position of the
picture.
V. Position
Adjust the vertical position of the
picture.
Black Level
Adjust the black level of the picture.
Contrast Contrast from Digital-register.
Cool
Recall cool Color Temperature from
EEPROM.
STD
Recall standard Color Temperature
from EEPROM.
Warm
Recall warm Color Temperature
from EEPROM.
White Balance
User
Adjust the value of the
Red/Green/Blue user color
temperature.
OSD H-Position
Adjust the horizontal position of the
OSD.
OSD V-Position
Adjust the vertical position of the
OSD.
Scaling
Adjust the sharpness of the
pictures.
English
Set OSD display language to
English.
Español
Set OSD display language to
Spaish.
Français
Set OSD display language to
French.
中文
Set OSD display language to
Chinese.
日本语
Set OSD display language to
Japanese.
Page 8
15” LCD Color Monitor Sharp LL-153A
8
Information
Show the model, the S/N and the
Usage time.
Off The off timer is off
On The off timer is on
4. Input/Output Specification
4.1 Input Signal Connector
D-SUB connector
Pin No. Description Pin No. Description
1. Red Video 9. +5V Supply
2. Green Video 10. GND
3. Blue Video 11. NC
4. NC 12. DDC-Serial Data
5. GND 13. H-Sync
6. Red Ground 14. V-Sync
7. Green Ground 15. DDC-Serial Clock
8. Blue ground
Analog Connector
15
6
10
11 15
Page 9
15” LCD Color Monitor Sharp LL-153A
9
4.2 Factory Preset Display Modes
4.3 Power Supply
The power supply should be integrated to the monitor housing.
A/C Line voltage range : 100 V ~ 240 V
A/C Line frequency range
: 50 ± 3Hz, 60 ± 3Hz
Current : 1.5A max at 100V; 0.8A max at 240 V
Peak surge current : < 55A peak at 240 VAC and cold starting
Leakage current : < 3.5mA
Power line surge : No advance effects (no loss of information or defect)
With a maximum of 1 half-wave missing per second
DC output Voltage
: 5VDC ± 5％; 12VDC± 5％
Current
1.5Amp (5V) ；2 Amp (12V)
Page 10
15” LCD Color Monitor Sharp LL-153A
10
4.4 Panel Specification
4.4.1 Display Characteristics
Page 11
15” LCD Color Monitor Sharp LL-153A
11
4.4.2 Optical Characteristics
4.4.3 Electrical
Characteristics
TFT LCD Module
Page 12
15” LCD Color Monitor Sharp LL-153A
12
Back- Light Unit
Page 13
15” LCD Color Monitor Sharp LL-153A
13
5. Block Diagram
5.1 Soft Flow Chart
1
2
N
Y
5
Y
N
10
Y
N
12
Y
N
7
N
6
4
3
9
14
11
13
Y
N
15
Y
N
16
17
19
Y
N
18
Page 14
15” LCD Color Monitor Sharp LL-153A
14
1) MCU initializes.
2) Is the EPROM blank?
3) Program the EPROM by default values.
4) Get the PWM value of brightness from EPROM.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EPROM.
Turn on the LED and set it to green color.
Scalar initializes.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are there any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappears.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?
Page 15
15” LCD Color Monitor Sharp LL-153A
15
5.2 Electrical Block Diagram
5.2.1 Main Board
Scalar TSUM13AK
(Include:ADC,OSD,MCU etc.)
LCD Interface
Flash memory
OSD Control
Interface
(Key pad)
EEPROM
24C16
Crystal
14.31818MHz
EEPROM
24C02
EPR_SDA
EPR_SCL
DB15_SDA
DB15_SCL
H-SYNC
V-SYNC
RXD
TXD
RGB
D-Sub
Connector
Page 16
15” LCD Color Monitor Sharp LL-153A
16
5.2.2 Inverter/Power Board
Start Circuit: R909、R910、R931
CN902
EMI filter
Bridge
Rectifier
and Filter
PWM
Control IC
Transformer
Over
Voltage
Protect
Rectifier
diodes
AC input
12V
ON/OFF Control
PWM
Control IC
Feedback
Circuit
Output
Circuit
Transformer
MOSFET
Q805
Lamp
ON/OFF
DIM
PWM
Feedback
Circuit
12V
5V
Page 17
15” LCD Color Monitor Sharp LL-153A
17
6. Schematic
6.1 Main Board
VCC1.8
PA[0..7]
+5V
TSUM13AK SCHEMATIC
B5
5.PANEL INTERFACE
VLCD
PA[0..7]
PB[12..21]
PA[12..13]
+3V3
XGA/SXGA
VLCD
VLCD
+12V
+5V
TOP
A
TSUM13AK
B
15Monday, May 30, 2005
Titl e
Size Document Number Rev
Date: Sheet
of
+12V
B3
3.INPUT
RIN
GIN
BIN
VSYNC
GNDR
GNDG
GNDB
DET_VGA
HSYNC
SOG
DDCA_SDA
DDCA_SCL
+5V
DDC_WP
PB[12..21]
+3V3
+5V
PA[12..13]
VCC1.8
+3V3
B2
2.POW ER
on_Panel
on_BACKLIGHT
Adj_BACKLIGH T
VCC1.8
VLCD
+5V
+3V3
+12V
LVDS OUTPUT
B4
4.SCALER
RIN
GIN
SOG
BIN
GNDR
GNDG
GNDB
HSYNC
VSYNC
Adj_BACKLIGHT
VCC1.8
+3V3
PA[0..7]
DDCA_SDA
DDCA_SCL
DET_VGA
on_BACKLIGH T
on_Panel
+5V
PB[12..21]
+12V
PA[12..13]
DDC_WP
+3V3
Page 18
15” LCD Color Monitor Sharp LL-153A
18
R706
NC
Q701
PMBS3904
R606
33K 1/16W
5V
+
C610
100uF/25V
GND
R715
NC
R701
1K 1/16W
PGATE
Adj_BACKLIGH T(4)
keep away from L602
+
C707
100uF/25V
C714
NC
GND
C711
0.1uF
VLCD
+12V
C613
0.001uF
GND
FB413
120 OHM
PANEL3.3
on_BACKLIGH T (4)
POWER
A
TSUM13AK
B
25Wednesday , June 01, 2005
Titl e
Size Document Number Rev
Date: Sheet of
GND
VLCD (5)
+3V3 (3,4,5)
U601
LM3485
1
4
5
8
2
3
6
7
ISENSE
FB
ADJ
VIN
AGND
N.C
PWGND
PGATE
C611
0.001uF
+5V
C709
0.1uF
BL_ADJ
C603
0.1uF
+5V(3,4)
GND
R607
33K 1/16W 1%
U602
AIC1084-18PM
3
1
2
VIN
ADJ
VOUT
+5V
R705
4.7K 1/ 16W
PANEL3.3
VCC1. 8
+3V3
+5V
F602FUSE_1. 5A
U702
NC
3
1
2
VIN
ADJ
VOUT
TO-263
+12V
R708
10K 1/16W
R712 4.7K 1/16W
C713
NC
+5V
C614
0.001uF
VCC1. 8 (4)
on_Panel(4)
C715
NC
TO-263
5V
L602
22uH
Q602
AO3401L
1
3
2
+12V (4)
keep shorter
+
C602
47uF/25V
+3V3
R605
22 1/16W
C612
0.001uF
D602
SSM54
Q704
AO3401L
Q703
PMBS3904
+
C710
100uF/25V
R714
10K 1/16W
+5V
R703
NC
R608
20K 1/16W
CN701
CONN
2
4
6
8
10
12
1
3
5
7
9
11
R716
NC
+
C609
220uF/25V
C701
NC
FB414
NC
R707
1K 1/16W
GND
C718
NC
+3V3
+3V3
BL_ON
Q706
NC
32
1
FB701
120 OHM
layout together
+12V
+
C712
NC
C604
0.1uF
+
C601
47uF/25V
R731
1K 1/16W
C706
0.1uF
R723 51K 1/16W
+
C702
NC
R717
4.7K 1/ 16W
R710 NC
+
C717
47uF/25V
C708
1uF/25V
+5V
+3V3
R711
10K 1/16W
R702
0 1/16W
+5V(3,4)
R725
NC
Page 19
15” LCD Color Monitor Sharp LL-153A
19
R438
75 1/16W
GREEN-
C443
220pF
R437 470 1/ 16W
HSYNC (4)
GND
FB412 0 1/16W
C435 0.001uF
U202A
NC
1 2
147
ZD405
UDZS5.6B
DDCA_SCL(4)
+5V
VSYNC (4)
DET_VGA (4)
R445
NC
R439
75 1/16W
R440
75 1/16W
U201
M24C02WMN6
1
2
3
45
6
7
8
A0
A1
A2
VSSSDA
SCL
WP
VCC
U202B
NC
3 4
147
ESD_5V
CN405
DB15
1
6
2
7
3
8
4
9
5
11
12
13
14
15
10
1716
R470
1K 1/16W
ZD403
UDZS5. 6B
GNDB (4)
C436 0.047uF
FB411 0 1/16W
DDCA_SDA(4)
R480
0 1/16W
C442
47pF
RIN (4)
INPUT
A
TSUM13AK
B
35Tuesday, May 31, 2005
Titl e
Size Document Number Rev
Date: Sheet
of
FB407
120 OHM
R454 100 1/ 16W
VGA_CON
C444
1uF/25V
D407
BAV70
3
1
2
+5V
GND
C113
0.1uF
D404
BAV99
3
1
2
GNDR (4)
R494 0 1/ 16W
R443 100 1/ 16W
R446 150 1/ 16W
R447 1K 1/ 16W
R452
NC
C433 0.047uF
FB409 0 1/16W
VSI
R451
4.7K 1/16W
R455
100 1/16W
D405
BAV99
3
1
2
R486
100 1/16W
R435 56 1/ 16W
C434 0.047uF
GIN (4)
PC5V
GREEN+
ZD406
UDZS5.6B
BLUE+
C437 0.047uF
HSI
SOG (4)
SDA_VGA
C439 0.1uF
R448
2.2K 1/16W
C440 0.1uF
GNDG (4)
R434 56 1/ 16W
R444
NC
R436 56 1/ 16W
C441 0.1uF
PC5V
R449
2.2K 1/16W
PC5V
ZD412
UDZS5.6B
+3V3
BIN (4)
RED-
+5V
D403
BAV99
3
1
2
U202E
NC
11 10
147
R450
4.7K 1/16W
R453 100 1/ 16W
C438 0.047uF
ZD402
UDZS5. 6B
BLUE-
VCC
DDC_WP (4)
RED+
ZD404
0 1/16W
R493 0 1/ 16W
U202F
NC
13 12
147
C432 0.047uF
R441 100 1/ 16W
SCL_VGA
ZD401
UDZS5. 6B
ESD_5V
R442 100 1/ 16W
+5V (2,4)
Page 20
15” LCD Color Monitor Sharp LL-153A
20
AVDD
R412
NC
C426
0.1uF
PA2
PB19
LED_A
R415
10K 1/16W
R425
10K 1/16W
OUT-R+
+5V (2,3)
R403
390 1%
C445
0.1uF
+3V3(2,3,5)
RST
VDDP
+3V3
RST
KEY_POWER
P[0..7]
C417
1uF/25V
U402
SST25VF010-33
1
2
3
4 5
6
7
8
CE#
SDO
WP#
VSS SD I
SCK
HOLD#
VDD
R420 1K 1/16W
VMPLL
+3V3
C413
0.1uF
FB406
120 OHM
R484 1K 1/16W
R457
NC
VSYNC(3)
R431 NC
PB[12..21] (5)
KEY_AUTO1
LED_A
PA7
C423 22pF
R416
10K 1/16W
PA3
R485 0 1/8W
BIN(3)
PB17
KEY_MENU
PB13
Q403
PMBS3906
+3V3
KEY_LEFT
U401
TSUM13AK
59
56
57
54
58
55
53
63
64
51
62
61
70
72
71
73
79
21
108
32
33
109
110
111
112
113
114
118
119
120
121
122
123
124
125
126
127
107
106
105
41
47
39
40
42
43
44
45
46
48
49
3896116
67
12
104
102
11
14
68
65
66
36
37
29
50
97
69
78
20
22
23
24
27
28
30
31
35
76
77
19
100
101
98
99
93
94
91
92
89
90
9
10
15
16
17
18
2
3
5
6
7
8
128
1
80
81
88
87
86
85
84
83
82
25
26
75
74
52344
95
103
115
117
60
13
RIN0P
GIN0P
SOGIN0
BIN0P
RIN0N
GIN0N
BIN0N
HSYNC0
VSYNC0
REXT
REFP
REFM
SDO
SCK
SCZ
SDI
GPIO_P27/PWM1
PWM1/GPIO_P25
NC/LVACKM/NC
XIN
XOUT
RA1P/LVA2P/RA2
RA1N/LVA2M/RA3
RA2P/LVA1P/RA4
RA2N/LVA1M/RA5
RA3P/LVA0P/RA6
RA3N/LVA0M/RA7
CLKAP/LVB3P/LHSY NC
CLKAN/LVB3M/LVSY NC
CLKBP/LVBCKP/LC K_ODD
CLKBN/LVBCKM/LDE
NC/LVB2P/N C
NC/LVB2M/NC
BB1P/LVB1P/BB2
BB1N/LVB1M/BB3
BB2P/LVB0P/BB4
BB2N/LVB0M/BB5
NC/LVACKP/NC
GA3N/LVA3M/GA7
GA3P/LVA3P/GA6
GND
GND
RX2P
RX2N
RX1P
RX1N
AVDD_DVI
RX0P
RX0N
RXCKP
RXCKN
GND
GND
GND
VDDP
VDDC
MODE[ 1]
MODE[ 0]
VCTRL
VDDP
VDD_OTP
DDCA_SDA
DDCA_SCL
DDCD_SDA
DDCD_SCL
PWM0/GPIO_P26
AVDD_DVI
VDDC
GPIO_P15
PWM2/GPIO_P24
GPIO_P16
GPIO_P17/SAR0
GPIO_P00/SAR1
GPIO_P01/SAR2
GPIO_P06
GPIO_P07
GPIO_P13
GPIO_P14
GPIO_P16
DDCROM_SDA
DDCROM_SCL
RST
GA2P/NC/GA4
GA2N/NC/GA5
GA1P/NC/GA2
GA1N/NC/GA3
BA3P/NC/BA6
BA3N/NC/ BA7
BA2P/NC/BA4
BA2N/NC/ BA5
BA1P/NC/BA2
BA1N/NC/ BA3
RB1P/NC/RB2
RB1N/NC/RB3
RB2P/NC/RB4
RB2N/NC/RB5
RB3P/NC/RB6
RB3N/NC/RB7
GB1P/NC/GB2
GB1N/NC/GB3
GB2P/NC/GB4
GB2N/NC/GB5
GB3P/NC/GB6
GB3N/NC/GB7
BB3P/NC/BB6
BB3N/NC/ BB7
ESP
OSP
GPO0
GPO1
GPO2
GPO3
GPO4
GPO5
GPO6
GPIO_P02/SAR3
GPIO_P03
GPIO_P22
GPIO_P23
AVDD_PLL
AVDD_MPLL
AVDD_MPLL
VDDP
VDDP
VDDP
VDDC
AVDD_ADC
GND
on_BACKLIGHT (2)
VDDC
FB403
120 OHM
OUT-R+
R489
NC
SOG(3)
+12V (2)
VDDC
KEY_RIGHT1
KEY_MENU
KEY_POWER1
PB12
KEY_RIGHT
GND
C421 22pF
F401
FUSE 1A 0603
R422 4.7K 1/16W
R426
10K 1/16W
SCALER
A
TSUM13AK
C
45Tuesday, May 31, 2005
Title
Size Document Number Rev
Date: Sheet
of
+5V
PB14
KEY_LEFT1
C405
0.1uF
3
KEY_POWER1
ROM_WP#
C410
0.1uF
VMPLL
LED_G
X401
14.318MHz
+3V3(2,3,5)
+12V
R487
NC
R475
10K 1/16W
Q401
PMBS3906
Volume
R483 1K 1/16W
R405
NC
R477
10K 1/16W
Volume
OUT-L-
C407
0.1uF
C414
0.1uF
PA12
VCC1.8
ZD408
UDZS5.6B
ZD410
UDZS5.6B
DDC_WP (3)
GND
ROM_WP#
R491
10K 1/16W
C409
0.1uF
R476
10K 1/16W
R406
NC
R414
100 1/16W
+
C408
10uF/50V
OUT-R-
R421 0 1/16W
FB402
120 OHM
GNDG(3)
KEY_MENU1
AUDIO_MUTE
R427 100 1/ 16W
R492
10K 1/16W
C429
0.1uF
VDVI
PB15
U405
MAX810STR-2.9V
1
2
3
GND
RESET
Vcc
VPLL
+3V3
LED_G
R408
10K 1/16W
DDCA_SDA(3)
PA[0..7] (5)
AVDD
OUT-L-
R496 10K 1/16W
+3V3(2,3,5)
+5V
KEY_RIGH T
OUT-L+
C401
0.1uF
LED_A
PB21
R402NCR401
NC
GNDR(3)
+3V3
ZD409
UDZS5.6B
C425
1uF/25V
C446
0.1uF
on_PANEL (2)
KEY_LEFT
C415
0.1uF
R490
NC
C428
0.1uF
+5V (2,3)
R419 0 1/ 16W
ZD414
UDZS5.6B
VCC1.8(2)
R428 100 1/ 16W
+3V3
PA1
KEY_LEFT1
DET_VGA (3)
AVDD
C412
0.1uF
+5V
R495 10K 1/ 16W
VPLL
+5V
PB[12..21]
AUDIO_MUTE
U303
M24C1 6
1
2
3
45
6
7
8
A0
A1
A2
VSSSI
SCK
WP
VCC
F601 FUSE_2A
CN404
CONN
2
4
6
8
10
12
14
1
3
5
7
9
11
13
+3V3
C430
0.1uF
C404
0.1uF
DDCA_SCL(3)
KEY_POWER
OUT-L+
VDDP
ZD413
UDZS5.6B
R409
100 1/16W
R410 N C
C406
0.1uF
adj_BACKLIGHT (2)
R474
10K 1/16W
FB405
120 OHM
R430
1K 1/16W
R418 1K 1/16W
C427
0.1uF
C411
0.1uF
PA13
C419
0.1uF
GNDB(3)
AUDIO_STBY
C402
0.1uF
R488
10K 1/16W
R413
10K 1/16W
PB16
C420
0.1uF
+3V3
R407 N C
RIN(3)
PA5
+3V3
F402
FUSE 1A 0603
ZD411
UDZS5.6B
GIN(3)
C447
0.1uF
PB18
C422
NC
+3V3(2,3,5)
VDVI+3V3
PA6
ZD407
UDZS5.6B
C416
0.1uF
CN403
CONN
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
R423 4.7K 1/16W
Q405
PMBS3904
HSYNC(3)
RSDS/LVDS/TTL
KEY_AUTO
LED_G
KEY_MENU1
FB404
120 OHM
1
R433 1K 1/ 16W
Q404
PMBS3904
+
C403
10uF/50V
AUDIO_STBY
PA0
R417 NC
KEY_AUTO1
2
OUT-R-
R481 100 1/ 16W
R411 1K 1/ 16W
R478
100K 1/16W
R429 100 1/ 16W
FB401
120 OHM
R424
10K 1/16W
R482
10K 1/16W
+3V3
GND
PB20
R456
1K 1/16W
C448
0.1uF
C424 NC
+5V
PA4
KEY_RIGHT1
R458
10K 1/16W
R479
10K 1/16W
Q402
NC
32
1
+5V
PA[12..13] (5)
+3V3
CN402
NC
1
2
3
4
+3V3(2,3,5)
KEY_AUTO
Page 21
15” LCD Color Monitor Sharp LL-153A
21
LVB3P
LVA3M
RXO0+
LVBCKM
LVACKM
C720
0.1uF
PA1
+3V3 (2,3,4)
CN101
CONN
2
4
6
8
10
12
14
16
18
20
22
24
1
3
5
7
9
11
13
15
17
19
21
23
LVA1M
LVA0P
LVA3M
LVB0P
RXE3-
LVBCKM
RXOC+
PA3
LVA0M
LVB1P
PB13
VLCD (2)
LVB1M
PB21
RXO2-
PB14
LVBCKP
PB[12..21]
LVB1P
RXEC-
PA[0..7](4)
LVB2M
RXE2+
PA2
PA5
PANEL INT ERFACE
A
TSUM13AK
B
55Tuesday, May 31, 2005
Titl e
Size Document Number Rev
Date: Sheet
of
LVA3P
LVB2P
R728
2.2K 1/16W
LVB3M
PB15
LVA1M
LVBCKP
RXE0-
PB[12..21](4)
LVA1P
PB12
LVB0M
+3V3
LVA3P
PB19
R732
1K 1/8W
LVACKP
LVA2M
LVB3P
LVACKP
PA0
LVB1M
+
C719
47uF/25V
PA7
PA[12..13](4)
RXO2+
LVA2M
PB16
RXE1-
PA[0..7]
RXOC-
PB18
PA6
LVB2P
RXE1+
LVB3M
VLCD
LVDS_TEST
RXE0+
LVB2M
PA4
LVA2P
LVB0P
RXO1+
RXO3+
R730
NC
LVA1P
LVB0M
LVACKM
RXE2-
PB20
LVA0M
R729
NC
RXE3+
RXO3-
LVA2P
RXO1-
PA12
PA13
PB17
RXEC+
LVA0P
Page 22
15” LCD Color Monitor Sharp LL-153A
22
6.2 Inverter Board
R812
10K 1/10W
C828
0.1uF/50V
N.C C829
0.1uF/50V
J811
TIN C OATED
C813
1500PF/50V
C818
470PF/50V
N.C R806
470 1/8W
R827
3.3K 1/10W
R845
1M 1/ 10W
D805
LL4148WP
Q807
RK7002
Q804
RK7002
VCC
C823
1500PF/50V
C822
1500PF/50V
C825
10PF/3KV
C826
5PF/3KV
C827
470PF/50V
RJ802
0 1/8W
RJ804
0 1/8W
RJ801
0 1/8W
1
2
CN802
33G8021-2D-U
1
2
CN803
33G8021-2D-U
1
2
CN804
33G8021-2D-U
J812
TIN COATED
R844
1M 1/ 10W
J814
TIN C OATED
J815
TIN COATED
J816
TIN COATED
J817
TIN C OATED
Q808
RK7002
J818
TIN COATED
J819
TIN C OATED
J820
TIN COATED
R804
10K 1/8W
J821
TIN COATED
J823
TIN C OATED
J824
TIN COATED
PWPC1742HDP3P(715G1927 1)
C821
0.1uF/25V
C824
0.1uF/25V
C830
0.1uF/25V
R846
1M 1/ 10W
C801
0.1uF/50V
D808
LL4148WP
C832
Q809
RK7002
R835
1M 1/ 10W
Title
Size Docum ent Number Rev
Date: Sheet
of
B
SHARP LL-174A 4 LAMPS INVERTER
AOC (Top Victory) Electronics Co., Ltd.
22
Thursday, May 04, 2006
C831
0.1uF/ 25V
R847
1M 1/ 10W
Q810
RK7002
D807
LL4148WP
N.C R838
0 1/8W
R821
100K 1/10W
R809
200K 1/10W
R848
560 1/10W
R805
470 1/8W
N.C C814
1000P/50V
C809
0.047UF/50V
32
1
Q801
PMBS3904
R810
100K 1/10W
N.C R833
75K 1/10W
R825
560 1/10W
R815
100K 1/10W
5
3
7
4
1 8
PT801
80GL19T-36-DN
C816
10PF/3KV
R808
200K 1/8W
32
1
Q803
PMBS3904
R816
1M 1/ 10W
R842
10 1/10W
ZD801
RLZ5.6B
1
2
CN801
33G8021-2D-U
C804
1.5uF/25V
R814
56K 1/10W
J825
TIN C OATED
R817
39K 1/10W
C805
1000PF/50V
C812
1500PF/50V
32
1
Q802
PMBS3904
3
1
2
D801
BAV70
R822
3M / 1/2W
5
3
7
4
1 8
PT802
80GL19T-36-DN
C803
0.01UF/50V
R829
15 1/ 8W
R828
15 1/8W
R836
1K 1/10W
R807
22 1/8W
3
12D802
BAV99
R813
1M 1/ 10W
R841
430 1/10W 1%
R837
10 1/10W
R802
300K 1/8W
N.C R839
33K 1/8W
R826
430 1/10W 1%
DRV1
1
VDDA
2
TIMER
3
DIM
4
ISEN
5
VSEN
6
OVPT
7
NC18NC2
9
ENA
10
LCT
11
SSTCMP
12
CT
13
GNDA
14
DRV2
15
PGND
16
IC801
OZ9938
S1N1G1N2S2N3G2N
4
D2N5D2N6D1N7D1N
8
Q805
AM9945
R820
15K 1/10W
C808
6800PF/50V
R819
15 1/8W
S1N1G1N2S2N3G2N
4
D2N5D2N6D1N7D1N
8
Q806
AM9945
C817
5PF/3KV
C807
0.01UF/ 50V
C819
0.047UF/25V
R811
47K 1/ 10W
C810
470PF/50V
R830
15K 1/10W
R818
15 1/8W
C806
1UF/25V
R803
10K 1/10W
VCC
D806
LL4148WP
R831
100K 1/10W
R843
1K 1/10W
3
1
2
D803
BAV70
+
C811
470UF/25V
+
C820
470UF/25V
3
12D804
BAV99
R832
3M / 1/2W
R834
3.3K 1/10W
N.C R823
75K 1/10W
N.C R840
33K 1/8W
N.C C815
1000P/50V
0.1uF/25V
D809
LL4148WP
+12V
ON/OFF
+5V
DIM
Page 23
15” LCD Color Monitor Sharp LL-153A
23
6.3 Adapter Board
!
ZD901
RLZ22B
1 2
!
!
R932
680K 1/4W
D905
FR103
!
L902
17.0mH
1
4
2
3
t
NR901
NTCR
R925
0 1/8W
C914
0.1uF
ON/OFF
C913
NC
R934
100 1/4W
C921
0.001uF/250V
C919
470pF/25V
R901
680K 1/4W
ZD904
RLZ12B
1 2
R922
2.43K 1/8W
C918
1uF/25V
!
C910
0.1uF/25V
+
C906
470UF/25V
R931
430K 1/4W
!
F801
NC
CN903
CONN(NC)
1
2
3
C933
0.0022uF
!
+5V
+12V
R912
2.7KΩ 1/8W
R908
680K 1/4W
R909
430K 1/4W
R905
100K 2W
C902
0.001uF/250V
!
+12V
R914
5.1 1/4W
D904
SP10150
1
2
3
F902
FUSE
CN901
SOCKET
12
3
C917
0.001uF
!
!
C907
0.1uF/25V
R906
100 1/4W
+
C905
100uF/450V
FOR SHARP LL154 (PWPC521CP1P)
POWER OUTPUT 12V & 5 V
TPV (Top Victory) Electronics Co., Ltd.
12
Titl e
Size Document Number Rev
Date: Sheet
of
C932
0.001uF
Q901
PMBS3906
CN302
CONN & WIRE
1
2
3
C915
0.1uF/25V
F
!
-+
BD901
U4KB80R
2
4
3
1
R923
1K 1/8W
L901
2.0MH
1
4
2
3
!
GND
SG902 NC
FB901
BEAD
12
D903
LL4148WP
+
C911
470UF/25V
CN301
PHONEJAC K
1
5
2
4
3
R937 100 1/4W
R904
0.68Ω 2W
+
C912
1000uF/25V
IC903
AZ431AZ-AE1
R930
100KΩ 1% 1/4W
R921
3.6K 1/8W
R928
220 1/4W
R903
680K 1/4W
D901
FR107
!
+5V
D906
0Ω 1/4W
C916
0.1uF/25V
R910
430K 1/4W
CN902
CONN
2
4
6
8
10
12
1
3
5
7
9
11
R936 100 1/4W
C930
1500pF/1KV
!
+
C909
1000uF/25V
DIM
!
!
IC902
PC123X8YFZOF
12
43
R915
100 1/8W
R935
100 1/4W
R924
1K 1/8W
R926
1K 1/8W
ZD903
PTZ7.5B
1 2
+
C904
NC
R927
100 1/4W
+
C922
22uF/50V
R902
680K 1/4W
U?
LD7552BPS
1
2
3
4 5
6
7
8
GND
COMP
VCC
RT NC
CS
VCC
OUT
!
F901
FUSE
ZD906
NC
1 2
!
ZD905
RLZ18B
1 2
INL
+
C908
NC
L903
3.5uH
R911
4.7K 1/4W
R907
680K 1/4W
D902
SP10150
1
2
3
C903
0.47uF/275V
R920
33K 1/8W
L904
3.5uH
R918
10 1/4W
C931
0.0022uF
SG901 NC
!
R913
4.7K 1/8W
T901
POWER X'FMR
11
10
9
8
7
5
6
4
3
2
1
C901
0.001uF/250V
VAR901
Varistor
Q903
2SK2645-54MR
ZD902
RLZ5.1B
1 2
C920
NC
R916 100 1/4W
R919
10K 1/8W
Q902
PMBS3904
INR
Page 24
15” LCD Color Monitor Sharp LL-153A
24
6.4 Audio Board
Page 25
15” LCD Color Monitor Sharp LL-153A
25
7. PCB Layout
7.1 Main Board
Page 26
15” LCD Color Monitor Sharp LL-153A
26
7.2 PWPC Board
Page 27
15” LCD Color Monitor Sharp LL-153A
27
7.3 Audio Board
715G1144-3-SH
Page 28
15” LCD Color Monitor Sharp LL-153A
28
7.4 Key Board
8. Maintainability
8.1 Equipments and Tools Requirement
1. Voltmeter.150
2. Oscilloscope.
3. Pattern Generator.
4. DDC Tool with an IBM Compatible Computer.
5. Alignment Tool.
6. LCD Color Analyzer.
7. Service Manual.
8.
User Manual.
Page 29
15” LCD Color Monitor Sharp LL-153A
29
8.2 Trouble Shooting
8.2.1 MAIN BOARD
NO SCREEN APPEAR
Note:1. If replace “MAIN-BOARD” , Please re-do “DDC-content” programmed & “WHITE-Balance”.
2. If replace “Power Board” only, Please re-do “ WHITE-Balance”
Measured CN701 pin5,6 = 12 V?
Measured CN701 pin 9,10= 5V?
Measured U702 pin 2= 3.3V?
Measured U602 pin 2= 1.8V?
Measured CN402 pin 1/2 = 5V?
Measured CN402 pin 3/4 = 3.3V?
NG
Check Correspondent component.
Is there any shortage or cold solder?
Yes .there have OSD show
Yes, all DC level exist
Disconnected the Signal cable( Loose the
Signal cable ),Is the screen show “Cable Not
Connected” ?
Connected the Signal cable again,
Check LED status.
Led Green
Replace U402
Flash Rom
No, nothing is
Connected the Signal cable
a
g
ain
Check Power switch is in Power-on
status , and check if Power switch had
been stuck ?
Led Orange
OK, Keyboard no
Led orange
Led Green
Check the Wire-Harness from CN405
Measured RGB (R434, R435, R436 )
H,V Input at U401 pin 63,64 ,was there
have signal ?
Check Correspondent
component short/open
( Protection Diode )
NG
OK, Wire tight
Check Panel-Power Circuit Block
OK ,Panel Power
Check U401 Data-output Block
Re-do White balance adjust
OK, input Normal
NG,still no screen
OK, clock
OK
OK, U201 data
Replace Power board and Check
Inverter control relative circuit
Replace U401 (TSUM13AK)
Page 30
15” LCD Color Monitor Sharp LL-153A
30
2.PANEL POWER CIRCUIT
3. INVERTER CONTROL RELATIVE CIRCUIT
NG , no transition
Check R731 should have response from 0V to 5V
When we switch the power switch from on to off
Check the PPWR panel power relative circuit,
Q704(pin2)
In normal operation, when LED =green, R731
should =0 v,
OK
NG, no Voltage
Measured the Q706 pin 3= 5 V?
Replace Q602 ( N-MOS, A03401)
OK
OK
Yes
NG
Check the Bklt-On relative circuit, R711, R712,
In normal operation, when LED =green,
R711,R712 Bklt-On should =5 v,
If Bklt-On no-response when the power switch
turn on-off, Replace U401 TSUM13AK
OK
NG
Replace Power board
& Re-do white balance
Measured the inverter connector
CN701
Pin2 on/off control=5V (on)
Pin4 PWM signal control dim 0V-5V
Replace power board to new-one and check
the screen is normal?
Mea
Page 31
15” LCD Color Monitor Sharp LL-153A
31
4. U4-DATA OUTPUT
8.2.2 Keypad Board
Measured DCLK(pin 65,66 from U401)
DVS, DHS (pin 63,64 from U401 )
Is the waveform ok?
DCLK around 48 MHZ , DVS=60.09Hz , DHS around 80
KHz ?(refer to input signal=640x480@60 Hz 31k, and
LED is Green)
OK
Replace TSUM13AK (U401) or
replace Main board.
Check TSUM13AK(U401)
Signal output (PIN105-114, 118-127)
Is the waveform ok ?
OK
If Main Board being replace, please
do the DDC – content reprogrammed
OK
NG , no transition
OSD is unstable or not working
Is Key Pad Board connecting normally?
Connect Key Pad Board
Is Button Switch normally?
Replace Button Switch
Y
N
N
Is Key Pad Board normally?
Replace Key Pad Board
Y
N
Y
Check main board
Page 32
15” LCD Color Monitor Sharp LL-153A
32
8.2.3 Power/Inverter Board
1.) No power
Check CN902 pin5, 6 = 12V
Check Interface board
OK
Check AC line volt 120V or 220V
NG
Change AC input
Check the voltage of C905(+)
Check bridge rectified circuit and F901 circut
Check start voltage for the pin3 of IC901
Change R909,R910,R931 and Change IC901
NG
Check the auxiliary voltage is bigger than 10V
smaller than 20V
1) Check IC901
2) Check ZD901, R915,C916…OVP circuit
OK
OK
OK
OK
NG
NG
NG
Check Q903,R918, R919, R928,T901,ZD905,D901
Check IC901 pin8 PWM wave
Check IC901
OK
NG
Page 33
15” LCD Color Monitor Sharp LL-153A
33
2.) W / LED , No Backlight
Check C811(+) =12V
NG
OK
Change L921 circuit
Check ON/OFF signal
Check Main board
NG
OK
Check IC801 pin2=5V
NG
OK
Change Q801,Q802,Q803 circuit
Check the pin1,15 of IC801 have saw tooth
wave
Check IC801 pin6,7,10
Check the pin5 of IC801
NG
OK
Check D802,D804,Q806 circuit
Check the resonant wave for PT801
NG
OK
Check the output of PT801
Check Q805 circuit
Check connecter & lamp
OK
NG
Change PT801
OK
NG
Page 34
15” LCD Color Monitor Sharp LL-153A
34
9. White-Balance, Luminance Adjustment
Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment.
1. How to do the CA210 MEM. Channel setting
A. Reference to CA210 user guide
B. Use “ SC” key and “ NEXT” key to modify x, y, Y value and use “ID” key to modify the TEXT description
Following is the procedure to do white-balance adjust:
2. Setting the color temp. you want
A. MEM.CHANNEL 1 (9300K color):
9300K color temp. parameter is x = 383±20, y = 297±15,
B. MEM.CHANNEL 2 (7500K color):
7500K color temp. parameter is x = 299±20, y = 315±15,
C. MEM.CHANNEL 3 (6500K color):
6500K color temp. parameter is x = 313±20, y = 329±15,
D. MEM.CHANNEL 3 (5000K color):
5000K color temp. parameter is x = 364±20, y = 359±15,
E. MEM.CHANNEL 3 (4000K color):
4000K color temp. parameter is x = 282±20, y = 384±15,
3. Into factory mode of SHARP LL-154A
Turn on power, press the MENU button, pull out the power cord, and then plug the power cord. Then the factory
OSD will be at the left top of the panel.
4. Bias adjustment:
Set the Contrast
to 64; Adjust the Brightness to 31.
5. Gain adjustment:
Move cursor to “-F-” and press MENU key
A. Adjust 9300K color-temperature
1. Switch the CA210 to 9300 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 283±15, y = 297±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
B. Adjust 7500K color-temperature
1. Switch the CA210 to 7500 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 299±15, y = 315±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
Page 35
15” LCD Color Monitor Sharp LL-153A
35
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
C. Adjust 6500K color-temperature
1. Switch the CA210 to STD (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 313±15, y = 329±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
D. Adjust 5000K color-temperature
1. Switch the CA210 to 5000 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 346±15, y = 359±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
E. Adjust 4000K color-temperature
1. Switch the CA210 to 4000 (with press “MODE” button)
2. Switch the MEM. Channel to Channel 3 (with up or down arrow on CA210)
3. The LCD-indicator on CA210 will show x = 282±15, y = 384±15,
4. Adjust the RED of color1 on factory window until CA210 indicator reached the value R=100
5. Adjust the GREEN of color1 on factory window until CA210 indicator reached the value G=100
6. Adjust the BLUE of color1 on factory window until CA210 indicator reached the value B=100
7. Repeat above procedure (item 4,5) until CA210 R/G value meet the tolerance =100±5
8. Repeat above procedure (item 6) until CA210 B value meet the tolerance =126±5
C. Turn the Power-button off to quit from factory mode.
Page 36
15” LCD Color Monitor Sharp LL-153A
36
10. Monitor Exploded View
Page 37
15” LCD Color Monitor Sharp LL-153A
37
11. BOM List
T56CM5NJXXXWAJ
Location Part No. Description
AUPC560KB8P AUPC BOARD FOR SMT
CBPC6CM5XWJ1 MAIN BOARD
KEPC6JA9 KEY BOARD
PWPC521CP1P G2152-F-X-X-1-20061121
11G6055 1 口字框
11G6082 1 CLAMP
12G 394 3 FOOT
12G6051 1 Thermal Pal
15G5791 1 VESA BRACKET
34G1298 8M ST REAR COVER
34G1630A8M T FRONT COVER
34G1631 8M T STAND
34G1632 8M T BASE
37G 495 1 HINGE
44G3231 15 EVA WASHER
45G8088607SH3 EPE BAG FOR MONITOR
52G 1150 SH BLACK TAPE
52G 1210 A AL Foil
52G6019 1 YELLOW TAPE
52G6022 22 GP Adhesive tape
52G6025 11582 MYLAR SHIELD
52G8001 8 NON-WOVEN FABRICS
78G 314 2 K LCD Speaker
85G 707 1 MAIN SHIELD
89G 17356G556 AUDIO CABLE
89G 728GAB901 SIGNAL CABLE
89G401D18NISA POWER CORD
95G8014 12 36 HARNESS 12P-12P 80mm
95G8014 16 46 HARNESS 12P-16P 180MM
95G8018 24701 D WIRE HARNESS 20P-24P 115
XN01A M1G 330 4120 SCREW
XN01B M1G 330 4120 SCREW
XN01C M1G 330 4120 SCREW
XN01A M1G 330 6120 SCREW
XN01A M1G1140 5120 SCREW
XN01A M1G1730 6120 M3*6
XN01B M1G1730 6120 M3*6
Page 38
15” LCD Color Monitor Sharp LL-153A
38
XN01C M1G1730 6120 M3*6
XN01A Q1G 330 6120 SCREW M3X6MM
XN01A Q1G 330 10120 SCREW
XN01A Q1G1030 8120 SCREW 3X8 NI
705GP503 1A SH PAPER PAD ASS'Y
750GLC50P1Q13N PANEL LCD CLAA150XP01Q 0
XN01A AM1G1740 10120 SCREW
D-SUB J02G 247 SH SCREW
J15G0030 1 MAIN FRAME
J44GP504624 1A CARTON
J45G8088609SH1 EPE BAG FOR BASE
J52G8025 11823 INSULATE SHEET
AUPC560KB8SMTP AUPC BOARD FOR SMT
12G 408 10 THERMAL PAD
CN204 33G3278 3 WAFER 3P PLUG 2.55mm
CN202 33G802414C H WAFER
U201 56G 616 1 AMPLIFIER IC E-TDA7496L
R212 61G 60222452T 220KOHM 5% 1/6W
C205 67G215L471 3N 470UF/16V
C207 67G215L471 3N 470UF/16V
C208 67G215L471 3N 470UF/16V
C201 67G215L681 4N 680UF 25V
C202 67G215L681 4N 680UF 25V
90G6093 1 HEAT SINK
AUPC560KB8AIP AUPC BOARD FOR AI
R207 61G0603102 CHIPR 1KOHM +-5% 1/10W
R208 61G0603102 CHIPR 1KOHM +-5% 1/10W
R201 61G0603183 CHIP resistors 1/10W
R203 61G0603183 CHIP resistors 1/10W
R210 61G0603203 RST CHIP 20K 1/10W 5%
R211 61G0603203 RST CHIP 20K 1/10W 5%
R202 61G0603204 RST CHIP 200K 1/10W 5%
C211 65G0805101 31 CHIP 100PF 50V NPD 0805
C212 65G0805101 31 CHIP 100PF 50V NPD 0805
C203 65G0805104 32 CHIP 0.1UF 50V X7R 0805
C213 65G0805104 32 CHIP 0.1UF 50V X7R 0805
C204 65G0805474 22 CHIP 0.47UF 25V Y5V 0805
C206 65G0805474 22 CHIP 0.47UF 25V Y5V 0805
C209 67G 2151097NT 1UF/50V
C210 67G 2151097NT 1UF/50V
Page 39
15” LCD Color Monitor Sharp LL-153A
39
715G1144 3 SH PCB
SMTC6CM5XWJ1 MAIN BOARD
CN404 33G801714H H PIN2*7
CN701 33G8027 12 WAFER 2*6P 2.0MM R/A
CN403 33G8027 16 WAFER 16PIN 2.0MM DIP
CN101 33G8027 24 H PIN 24P 2.0MM RIGHT ANGL
40G 45762412B CBPC LABEL
C403 67G215V100 7N LOW ESR EC 10UF 50V NCC
C408 67G215V100 7N LOW ESR EC 10UF 50V NCC
C610 67G215V101 4N LOW ESR EC 100UF 25V NCC
C707 67G215V101 4N LOW ESR EC 100UF 25V NCC
C710 67G215V101 4N LOW ESR EC 100UF 25V NCC
C609 67G215V221 4N LOW ESR EC 220UF 25V NCC
C601 67G215V470 4N LOW ESR EC 47UF 25V NCC
C602 67G215V470 4N LOW ESR EC 47UF 25V NCC
C717 67G215V470 4N LOW ESR EC 47UF 25V NCC
C719 67G215V470 4N LOW ESR EC 47UF 25V NCC
L602 73G 253158 L CHOKE COIL
CN405 88G353A15F HJ D-SUB 15PIN
90G6250 1 GP Radiator
X401 93G 22 53 CRYSTAL 14.31818MHZ HC-4
U601 56G 133 32 NS IC LM3485 MSOP-8
U401 56G 562102 TSUM13AK-LF PQFP-128
U602 56G 563 34 IC AIC1084-18PM TO-263
U405 56G 643 5A MAX810STRG SOT-23 IC
U201 56G1133 34 IC M24C02-WMN6TP
U303 56G1133 56 IC M24C16-WMN6TP
U402 56G1133 81 X SST25LF020A-33-4C-SAE
Q404 57G 417 4 PMBS3904/PLILIPS
Q405 57G 417 4 PMBS3904/PLILIPS
Q701 57G 417 4 PMBS3904/PLILIPS
Q703 57G 417 4 PMBS3904/PLILIPS
Q401 57G 417 6 PMBS3906 PNP
Q403 57G 417 6 PMBS3906 PNP
Q602 57G 763 1 AO3401L
Q704 57G 763 1 AO3401L
F401 61G0603000 CHIPR 0OHM +-5% 1/10W
F402 61G0603000 CHIPR 0OHM +-5% 1/10W
FB409 61G0603000 CHIPR 0OHM +-5% 1/10W
FB411 61G0603000 CHIPR 0OHM +-5% 1/10W
Page 40
15” LCD Color Monitor Sharp LL-153A
40
FB412 61G0603000 CHIPR 0OHM +-5% 1/10W
R419 61G0603000 CHIPR 0OHM +-5% 1/10W
R421 61G0603000 CHIPR 0OHM +-5% 1/10W
R480 61G0603000 CHIPR 0OHM +-5% 1/10W
R493 61G0603000 CHIPR 0OHM +-5% 1/10W
R494 61G0603000 CHIPR 0OHM +-5% 1/10W
R702 61G0603000 CHIPR 0OHM +-5% 1/10W
R409 61G0603101 CHIPR 100OHM +-5% 1/10W
R414 61G0603101 CHIPR 100OHM +-5% 1/10W
R427 61G0603101 CHIPR 100OHM +-5% 1/10W
R428 61G0603101 CHIPR 100OHM +-5% 1/10W
R429 61G0603101 CHIPR 100OHM +-5% 1/10W
R441 61G0603101 CHIPR 100OHM +-5% 1/10W
R442 61G0603101 CHIPR 100OHM +-5% 1/10W
R443 61G0603101 CHIPR 100OHM +-5% 1/10W
R445 61G0603101 CHIPR 100OHM +-5% 1/10W
R453 61G0603101 CHIPR 100OHM +-5% 1/10W
R454 61G0603101 CHIPR 100OHM +-5% 1/10W
R455 61G0603101 CHIPR 100OHM +-5% 1/10W
R481 61G0603101 CHIPR 100OHM +-5% 1/10W
R486 61G0603101 CHIPR 100OHM +-5% 1/10W
R411 61G0603102 CHIPR 1KOHM +-5% 1/10W
R418 61G0603102 CHIPR 1KOHM +-5% 1/10W
R420 61G0603102 CHIPR 1KOHM +-5% 1/10W
R430 61G0603102 CHIPR 1KOHM +-5% 1/10W
R433 61G0603102 CHIPR 1KOHM +-5% 1/10W
R447 61G0603102 CHIPR 1KOHM +-5% 1/10W
R456 61G0603102 CHIPR 1KOHM +-5% 1/10W
R470 61G0603102 CHIPR 1KOHM +-5% 1/10W
R483 61G0603102 CHIPR 1KOHM +-5% 1/10W
R484 61G0603102 CHIPR 1KOHM +-5% 1/10W
R701 61G0603102 CHIPR 1KOHM +-5% 1/10W
R707 61G0603102 CHIPR 1KOHM +-5% 1/10W
R731 61G0603102 CHIPR 1KOHM +-5% 1/10W
R408 61G0603103 CHIPR 10KOHM+-5% 1/10W
R413 61G0603103 CHIPR 10KOHM+-5% 1/10W
R415 61G0603103 CHIPR 10KOHM+-5% 1/10W
R416 61G0603103 CHIPR 10KOHM+-5% 1/10W
R424 61G0603103 CHIPR 10KOHM+-5% 1/10W
R425 61G0603103 CHIPR 10KOHM+-5% 1/10W
Page 41
15” LCD Color Monitor Sharp LL-153A
41
R426 61G0603103 CHIPR 10KOHM+-5% 1/10W
R458 61G0603103 CHIPR 10KOHM+-5% 1/10W
R474 61G0603103 CHIPR 10KOHM+-5% 1/10W
R475 61G0603103 CHIPR 10KOHM+-5% 1/10W
R476 61G0603103 CHIPR 10KOHM+-5% 1/10W
R477 61G0603103 CHIPR 10KOHM+-5% 1/10W
R479 61G0603103 CHIPR 10KOHM+-5% 1/10W
R488 61G0603103 CHIPR 10KOHM+-5% 1/10W
R490 61G0603103 CHIPR 10KOHM+-5% 1/10W
R491 61G0603103 CHIPR 10KOHM+-5% 1/10W
R492 61G0603103 CHIPR 10KOHM+-5% 1/10W
R495 61G0603103 CHIPR 10KOHM+-5% 1/10W
R496 61G0603103 CHIPR 10KOHM+-5% 1/10W
R708 61G0603103 CHIPR 10KOHM+-5% 1/10W
R711 61G0603103 CHIPR 10KOHM+-5% 1/10W
R714 61G0603103 CHIPR 10KOHM+-5% 1/10W
R478 61G0603104 CHIPR 100KOHM +-5% 1/10W
R446 61G0603151 CHIPR 150 OHM +-5% 1/10W
R608 61G0603200 2F RST CHIP 20K 1/10W 1%
R605 61G0603220 CHIPR 22OHM+-5% 1/10W
R448 61G0603222 CHIPR 2.2KOHM+-5% 1/10W
R449 61G0603222 CHIPR 2.2KOHM+-5% 1/10W
R728 61G0603222 CHIPR 2.2KOHM+-5% 1/10W
R607 61G0603330 2F RST CHIP 33K 1/10W 1%
R606 61G0603333 RST CHIP 33K 1/10W 5%
R403 61G0603390 0F 390OHM +-1%
R437 61G0603471 CHIPR 470OHM+-5%1/10W
R405 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R422 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R450 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R451 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R705 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R712 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R717 61G0603472 CHIP 4.7KOHM +-5% 1/10W
R723 61G0603513 CHIP 51K OHM
R434 61G0603560 RST CHIP 56R 1/10W 5%
R435 61G0603560 RST CHIP 56R 1/10W 5%
R436 61G0603560 RST CHIP 56R 1/10W 5%
R438 61G0603750 CHIPR 75OHM+-5%1/10W
R439 61G0603750 CHIPR 75OHM+-5%1/10W
Page 42
15” LCD Color Monitor Sharp LL-153A
42
R440 61G0603750 CHIPR 75OHM+-5%1/10W
ZD404 61G0805000 RST CHIP MAX 0R05 1/8W
F601 61G1206000 CHIP resistors 1/3W
F602 61G1206000 CHIP resistors 1/3W
R485 61G1206000 CHIP resistors 1/3W
R732 61G1206102 CHIP 1K OHM 5% 1/8W
C435 65G0603102 32 CHIP 1000PF 50 X7R
C611 65G0603102 32 CHIP 1000PF 50 X7R
C612 65G0603102 32 CHIP 1000PF 50 X7R
C613 65G0603102 32 CHIP 1000PF 50 X7R
C614 65G0603102 32 CHIP 1000PF 50 X7R
C113 65G0603104 32 CHIP 0.1UF 50V X7R
C401 65G0603104 32 CHIP 0.1UF 50V X7R
C402 65G0603104 32 CHIP 0.1UF 50V X7R
C404 65G0603104 32 CHIP 0.1UF 50V X7R
C405 65G0603104 32 CHIP 0.1UF 50V X7R
C406 65G0603104 32 CHIP 0.1UF 50V X7R
C407 65G0603104 32 CHIP 0.1UF 50V X7R
C409 65G0603104 32 CHIP 0.1UF 50V X7R
C410 65G0603104 32 CHIP 0.1UF 50V X7R
C411 65G0603104 32 CHIP 0.1UF 50V X7R
C412 65G0603104 32 CHIP 0.1UF 50V X7R
C413 65G0603104 32 CHIP 0.1UF 50V X7R
C414 65G0603104 32 CHIP 0.1UF 50V X7R
C415 65G0603104 32 CHIP 0.1UF 50V X7R
C416 65G0603104 32 CHIP 0.1UF 50V X7R
C419 65G0603104 32 CHIP 0.1UF 50V X7R
C420 65G0603104 32 CHIP 0.1UF 50V X7R
C426 65G0603104 32 CHIP 0.1UF 50V X7R
C427 65G0603104 32 CHIP 0.1UF 50V X7R
C428 65G0603104 32 CHIP 0.1UF 50V X7R
C429 65G0603104 32 CHIP 0.1UF 50V X7R
C430 65G0603104 32 CHIP 0.1UF 50V X7R
C439 65G0603104 32 CHIP 0.1UF 50V X7R
C440 65G0603104 32 CHIP 0.1UF 50V X7R
C441 65G0603104 32 CHIP 0.1UF 50V X7R
C445 65G0603104 32 CHIP 0.1UF 50V X7R
C446 65G0603104 32 CHIP 0.1UF 50V X7R
C447 65G0603104 32 CHIP 0.1UF 50V X7R
C448 65G0603104 32 CHIP 0.1UF 50V X7R
Page 43
15” LCD Color Monitor Sharp LL-153A
43
C603 65G0603104 32 CHIP 0.1UF 50V X7R
C604 65G0603104 32 CHIP 0.1UF 50V X7R
C701 65G0603104 32 CHIP 0.1UF 50V X7R
C706 65G0603104 32 CHIP 0.1UF 50V X7R
C709 65G0603104 32 CHIP 0.1UF 50V X7R
C711 65G0603104 32 CHIP 0.1UF 50V X7R
C720 65G0603104 32 CHIP 0.1UF 50V X7R
C421 65G0603220 31 CHIP 22PF 50V NPO
C423 65G0603220 31 CHIP 22PF 50V NPO
C443 65G0603221 31 CAP:CER 220PF 5% 50V SMT
C442 65G0603470 31 CHIP 47PF 50V NPO
C432 65G0603473 32 CHIP 47NF 50V X7R
C433 65G0603473 32 CHIP 47NF 50V X7R
C434 65G0603473 32 CHIP 47NF 50V X7R
C436 65G0603473 32 CHIP 47NF 50V X7R
C437 65G0603473 32 CHIP 47NF 50V X7R
C438 65G0603473 32 CHIP 47NF 50V X7R
C417 65G0805105 22 CHIP 1UF 25V X7R 0805
C425 65G0805105 22 CHIP 1UF 25V X7R 0805
C444 65G0805105 22 CHIP 1UF 25V X7R 0805
C708 65G0805105 22 CHIP 1UF 25V X7R 0805
FB401 71G 56K121 M GP CHIP BEAD 120OHM T
FB402 71G 56K121 M GP CHIP BEAD 120OHM T
FB403 71G 56K121 M GP CHIP BEAD 120OHM T
FB404 71G 56K121 M GP CHIP BEAD 120OHM T
FB405 71G 56K121 M GP CHIP BEAD 120OHM T
FB406 71G 56K121 M GP CHIP BEAD 120OHM T
FB407 71G 56K121 M GP CHIP BEAD 120OHM T
FB413 71G 56K121 M GP CHIP BEAD 120OHM T
FB701 71G 56K121 M GP CHIP BEAD 120OHM T
D407 93G 64 42 P BAV70 DIODE
D403 93G 6433P BAV99 SOT-23
D404 93G 6433P BAV99 SOT-23
D405 93G 6433P BAV99 SOT-23
ZD401 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD402 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD403 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD405 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD406 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD407 93G 39S 34 T ZENER DIODE UDZS5.6B
Page 44
15” LCD Color Monitor Sharp LL-153A
44
ZD408 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD409 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD410 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD411 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD412 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD413 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD414 93G 39S 34 T ZENER DIODE UDZS5.6B
D602 93G5004 2 SSM54PT SMA DIODE 5A 40V
715G1590 1 MAIN BOARD PCB
SMTKEPC6JA9 KEYBOARD FOR SMT
CN102 33G3802 2H WAFTER
CN103 33G3802 2H WAFTER
CN101 33G8027 12 H WAFER 2*6P 2.0mm R/A
R103 61G 60210152T CFR 1/6W 100OHM +-5%
R104 61G 60210152T CFR 1/6W 100OHM +-5%
R101 61G 60251152T CFR 1/6W 510OHM +-5%
R102 61G 60251152T CFR 1/6W 510OHM +-5%
SW1 77G 600 1GCJ Switch
SW2 77G 600 1GCJ Switch
SW3 77G 600 1GCJ Switch
SW4 77G 600 1GCJ Switch
SW5 77G 600 1GCJ Switch
D101 81G 12 1F GP LED
CN104 88G 30211K PHONE JOCK
J1 95G 900 58 WIRE HARNESS
ZD101 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD102 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD103 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD104 93G 39S 34 T ZENER DIODE UDZS5.6B
ZD105 93G 39S 34 T ZENER DIODE UDZS5.6B
715G1591 2 KEPC PCB
PW521CP1SMTP POWER BOARD FOR SMT
W901 9G6005 1 PIN FOOT
CN801 33G8020 2D AC CONN,2P R/A DIP BY ACES
CN802 33G8020 2D AC CONN,2P R/A DIP BY ACES
CN902 33G8027 12 WAFER 2*6P 2.0MM R/A
40G 45762412B CBPC LABEL
51G 6 45056863 RTV Glue
IC902 56G 139 3A PC123Y22FZOF
VAR901 61G 46 9 10471
Page 45
15” LCD Color Monitor Sharp LL-153A
45
NR901 61G 58080 WT NTCR
C903 63G 10747410S 0.47UF +-10% 250VAC
C816 65G 3J2206ET 22PF 5% 3KV TDK
C817 65G 3J5096ET 5PF 5% SL 3KV
C901 65G306M1022BM Y1.CAP.001UF 250VAC MURA
C902 65G306M1022BM Y1.CAP.001UF 250VAC MURA
C921 65G306M1022BM Y1.CAP.001UF 250VAC MURA
C909 67G215L102 4N LOW ESR 1000UF 25V
C912 67G215L102 4N LOW ESR 1000UF 25V
C811 67G215L471 4Q LOW ESR EC 470UF 25V UH
C906 67G215L471 4Q LOW ESR EC 470UF 25V UH
C911 67G215L471 4Q LOW ESR EC 470UF 25V UH
C905 67G215S10115Q LOWESR EC 100UF 450V PAG
FB901 71G 55 29 Φ3.5*Φ0.8*2.2\ 100MM>
L903 73G 253 91 LS CHOKE COIL
L904 73G 253 91 LS CHOKE COIL
L901 73L 174 53 LG GP LINE FILTER
L902 73L 174 55 LG GP LINE FILTER
PT801 80GL15T 30 DN X'FMR 74uH TK.2026.101
T901 80LL19T 7 LG GP TRANSFORMER
CN301 88G 30214K PHONE JACK 5PIN
BD901 93G 50460900 GBU408
D901 93G 6026T52T FR107-DO-41 1000V/1A
D905 93G 6038T52T FR103 DO-41 200V/1A
CN302 95G8013 3704 X HARNESS
705G 560 57S44 R905 ASS'Y
705G 780 57S7P Q903 ASS'Y
705GJ5K0 61001 R904 ASS'Y
705GJ5K0 87001 CN901 ASS'Y
705GJ5K0 93001 D902 ASS'Y
705GJ5K0 93002 D904 ASS'Y
705GJ5K0 95001 JP907 ASS'Y
PW521CP1AIP POWER FOR AI
IC901 56G 379 76 IC LD7552BPS SOP-8
IC801 56G 608 10 OZ9938GN SOIC-16
Q801 57G 417 4 PMBS3904/PLILIPS
Q802 57G 417 4 PMBS3904/PLILIPS
Q803 57G 417 4 PMBS3904/PLILIPS
Q902 57G 417 4 PMBS3904/PLILIPS
Q901 57G 417 6 PMBS3906 PNP
Page 46
15” LCD Color Monitor Sharp LL-153A
46
Q804 57G 759 2 TRANSISTOR RK7002 SOT-3
Q806 57G 759 2 TRANSISTOR RK7002 SOT-3
Q807 57G 759 2 TRANSISTOR RK7002 SOT-3
Q808 57G 759 2 TRANSISTOR RK7002 SOT-3
Q805 57G 763 14 AM9945N-T1-PF SOIC-8
R839 61G0805000 RST CHIP MAX 0R05 1/8W
R844 61G0805000 RST CHIP MAX 0R05 1/8W
R925 61G0805000 RST CHIP MAX 0R05 1/8W
RJ824 61G0805000 RST CHIP MAX 0R05 1/8W
R836 61G0805100 RST CHIP 10R 1/8W 5%
R837 61G0805100 RST CHIP 10R 1/8W 5%
R826 61G0805100 2F RST CHIP 10K 1/8W 1%
R915 61G0805101 RST CHIP 100R 1/8W 5%
R923 61G0805102 CHIPR 1K OHM +-5% 1/10W
R924 61G0805102 CHIPR 1K OHM +-5% 1/10W
R926 61G0805102 CHIPR 1K OHM +-5% 1/10W
R803 61G0805103 CHIP 10KOHM 1/10W
R804 61G0805103 CHIP 10KOHM 1/10W
R812 61G0805103 CHIP 10KOHM 1/10W
R820 61G0805103 CHIP 10KOHM 1/10W
R919 61G0805103 CHIP 10KOHM 1/10W
R810 61G0805104 RST CHIP 100K 1/8W 5%
R815 61G0805104 RST CHIP 100K 1/8W 5%
R821 61G0805104 RST CHIP 100K 1/8W 5%
R813 61G0805105 RST CHIP 1M 1/8W 5%
R816 61G0805105 RST CHIP 1M 1/8W 5%
R845 61G0805105 RST CHIP 1M 1/8W 5%
R847 61G0805105 RST CHIP 1M 1/8W 5%
R848 61G0805105 RST CHIP 1M 1/8W 5%
R809 61G0805204 RST CHIPR 200 KOHM +-5%
R807 61G0805220 RST CHIP 22R 1/8W 5%
R840 61G0805242 RST CHIP 2K4 1/8W 5%
R841 61G0805242 RST CHIP 2K4 1/8W 5%
R922 61G0805243 1F RST CHIPR 2.43 KOHM +-1%
R825 61G0805271 CHIPR 270 OHM +-50% 1/8W
R912 61G0805272 RST CHIP 2K7 1/8W 5%
R802 61G0805304 RST CHIPR 300 KOHM +-5%
R920 61G0805330 2F CHIP 33KOHM 1/10W/1%
R838 61G0805360 0F RST CHIPR 360 OHM +-1% 1
R921 61G0805360 1F CHIP 3.6KOHM 1/10W 1%
Page 47
15” LCD Color Monitor Sharp LL-153A
47
R817 61G0805360 2F RST CHIPR 36 KOHM +-1% 1
R843 61G0805471 RST CHIP 470R 1/8W 5%
R913 61G0805472 RST CHIP 4K7 1/8W 5%
R811 61G0805473 RST CHIP 47K 1/8W 5%
R827 61G0805510 1F RST CHIPR 5.1 KOHM +-1%
R814 61G0805563 RST CHIP 56K 1/8W 5%
D906 61G1206000 CHIP resistors 1/3W
JR902 61G1206000 CHIP resistors 1/3W
R801 61G1206000 CHIP resistors 1/3W
R918 61G1206100 RST CHIP 10R 1/4W 5%
R930 61G1206100 3F RST CHIPR 100 KOHM +-1%
R906 61G1206101 CHIP 100OHM 5% 1/8W
R916 61G1206101 CHIP 100OHM 5% 1/8W
R927 61G1206101 CHIP 100OHM 5% 1/8W
R934 61G1206101 CHIP 100OHM 5% 1/8W
R935 61G1206101 CHIP 100OHM 5% 1/8W
R936 61G1206101 CHIP 100OHM 5% 1/8W
R937 61G1206101 CHIP 100OHM 5% 1/8W
R806 61G1206105 CHIP 1MOHM 5% 1/8W
R818 61G1206150 RST CHIP 15R 1/4W 5%
R819 61G1206150 RST CHIP 15R 1/4W 5%
R808 61G1206204 RST CHIPR 200 KOHM +-5%
R909 61G1206434 RST CHIPR 430 KOHM +-5%
R910 61G1206434 RST CHIPR 430 KOHM +-5%
R931 61G1206434 RST CHIPR 430 KOHM +-5%
R805 61G1206471 RST CHIP 47OR 1/4W 5%
R911 61G1206472 CHIP 4.7KOHM 5% 18W
R914 61G1206519 CHIP resistors 1/3W
R901 61G1206684 CHIPR 680KOHM +-5% 1/8W
R902 61G1206684 CHIPR 680KOHM +-5% 1/8W
R903 61G1206684 CHIPR 680KOHM +-5% 1/8W
R907 61G1206684 CHIPR 680KOHM +-5% 1/8W
R908 61G1206684 CHIPR 680KOHM +-5% 1/8W
R932 61G1206684 CHIPR 680KOHM +-5% 1/8W
C805 65G0805102 32 CHIP 1000PF 50V X7R 0805
C917 65G0805102 32 CHIP 1000PF 50V X7R 0805
C807 65G0805103 32 CHIP 10000 PF 50V X7R 08
C803 65G0805104 22 CHIP 0.1UF 25VX7R 0805
C907 65G0805104 22 CHIP 0.1UF 25VX7R 0805
C910 65G0805104 22 CHIP 0.1UF 25VX7R 0805
Page 48
15” LCD Color Monitor Sharp LL-153A
48
C915 65G0805104 22 CHIP 0.1UF 25VX7R 0805
C916 65G0805104 22 CHIP 0.1UF 25VX7R 0805
C801 65G0805104 32 CHIP 0.1UF 50V X7R 0805
C820 65G0805104 32 CHIP 0.1UF 50V X7R 0805
C821 65G0805104 32 CHIP 0.1UF 50V X7R 0805
C822 65G0805104 32 CHIP 0.1UF 50V X7R 0805
C806 65G0805105 22 CHIP 1UF 25V X7R 0805
C918 65G0805105 22 CHIP 1UF 25V X7R 0805
C804 65G0805155 A2 1.5 UF 10V
C802 65G0805221 31 CHIP 220PF 50V NPO
C818 65G0805271 31 CHIP 270pF 50V NPO 0805
C919 65G0805471 21 CHIP 470PF 25V NPO 0805
C812 65G0805472 31 CHIP 4700PF 50V X7R 080
C813 65G0805472 31 CHIP 4700PF 50V X7R 080
C823 65G0805472 31 CHIP 4700PF 50V X7R 080
C824 65G0805472 31 CHIP 4700PF 50V X7R 080
C809 65G0805473 32 SMD 47NF +-10% 50V
C819 65G0805473 32 SMD 47NF +-10% 50V
C810 65G080556131G MLCC 0805 560PF G 50V NP
C808 65G0805682 32 CHIP 6.8nF 50V X7R 0805
C932 65G1206102 72 CHIP 1000PF 500V X7R
C914 65G1206104 32 CHIP 0.1UF 25V X7R 1206
C931 65G1206222 72 CHIP 2200PF 500V X7R
C933 65G1206222 72 CHIP 2200PF 500V X7R
D802 93G 64 33 BAV99 SOT-23
D801 93G 64 42 PP DIODE BAV70 SOT-23
D803 93G 64 44 S CHIP DIODE LL4148WP
D804 93G 64 44 S CHIP DIODE LL4148WP
D903 93G 64 44 S CHIP DIODE LL4148WP
ZD904 93G 39S 17 T RLZ12B LLDS
ZD903 93G 39S 19 T PTZ7.5B
ZD901 93G 39S 23 T GLZ22B
ZD801 93G 39S 24 T RLZ5.6B ROHM
ZD902 93G 39S 25 T RLZ5.1B ROHM
ZD905 93G 39S 44 T RLZ18B LLDS
CN901 6G 31500 2.0MM EYELET
C905 6G 31502 1.5MM RIVET
L901 6G 31502 1.5MM RIVET
L902 6G 31502 1.5MM RIVET
PT801 6G 31502 1.5MM RIVET
Page 49
15” LCD Color Monitor Sharp LL-153A
49
Q903 6G 31502 1.5MM RIVET
R904 6G 31502 1.5MM RIVET
T901 6G 31502 1.5MM RIVET
IC903 56G 158 10 T IC AZ431AZ-AE1 TO-92
R928 61G 20022152T 220OHM 1% 1/4W
R822 61G212Y305 KT MGFR 3M OHM +-5% 1/2W
C930 65G 1K152 1T 1500PF +/-10% 1KV Y5P
C922 67G 2152207NT 22UF/50V
F901 84G 55 7W 250V/3.15A FUSE
F902 84G 55 7W 250V/3.15A FUSE
715G2152 F PCB
R905 61G152M10458G 100K OHM 5% 2W
96G 29 6 SHRINK TUBE UL/CSA
51G 200 1 6342 Coolant Oil
Q903 57G 667 30 2SK2645-54MR TO-220F
90G6084 1 HEAT SINK
XN01A AM1G1730 8120 SCREW
R904 61G 2J68858G 0.68 OHM 5% 2W
96G 29 6 SHRINK TUBE UL/CSA
CN901 87G 501 36 S AC SOCKET
95G 900703 X WIRE HARNESS
96G 29 6 SHRINK TUBE UL/CSA
51G 200 1 6342 Coolant Oil
90G6084 1 HEAT SINK
D902 93G 60245 DIODE SP10150 ITO-220
XN01A AM1G1730 8120 SCREW
51G 200 1 6342 Coolant Oil
90G6084800 HEAT SINK
D904 93G 60245 DIODE SP10150 ITO-220
XN01A AM1G1730 8120 SCREW
96G 29 1 H.S.TUBE
44GP503 1A 1 PAPER PAD-1
44GP503 1A 2 PAPER PAD-2
44GP503 1A 3 PAPER PAD-3
Loading...