SHARP LK600D3HA19 Specification

Global LCD Panel Exchange Center
TFT-LCD Open Cell
www.panelook.com
TECHNICAL LITERATURE
FOR
No.
LD-K23453
DATE May. 17. 2011
MODEL No.
The technical literature is subject to change without notice.
So, please contact SHARP or its representative before designing
your product based on this literature.
LK600D3HA19
LIQUID CRYSTAL DISPLAY DIVISION
LARGE LIQUID CRYSTAL DISPLAY GROUP
SHARP CORPORATION
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
MODEL No. : LK600D3HA19
TL No. : LD-K23453
SPEC No. DATE
LD-K23453 2011.5.17 - - - 1st ISSUE
REVISED
www.panelook.com
RECORDS OF REVISION
No.
PAGE SUMMARY NOTE
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
r
]
r
1. Application
This technical literature applies to the color 60.0” TFT-LCD Open Cell LK600D3HA19.
* This technical literature is proprietary products of SHARP CORPORATION (“SHARP”) and includes materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP.
* In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains, automobiles, etc.), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken.
* Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for life support.
* SHARP assumes no responsibility for any damage resulting from the use of the device that does not comply with the instructions and the precautions specified in this technical literature.
* Contact and consult with a SHARP sales representative for any questions about this device.
2. Overview
This Open Cell is color active matrix LCD Open Cell incorporating amorphous silicon TFT (T
ransistor). It is composed of a color TFT-LCD panel, driver ICs and Source PWB.
T
The following contents can be achieved in using LK0DZ1C0xxx (C-PWB) and LK0DZ1C0xxx (CS-FPC) that SHARP specifies.
Graphics and texts can be displayed on a 1920 x RGB x 1080 dots panel with one billion colors by using 10bit+LVDS (L
And in order to improve the response time of LCD, this module applies the Over Shoot driving (O/S driving) technology for the control circuit. In the O/S driving technology, signals are being applied to the Liquid Crystal according to a pre-fixed process as an image signal of the present frame when a difference is found between image signal of the previous frame and that of the current frame after comparing them.
With combination of these technologies, motion blur can be reduced and clearer display performance can be realized.
ow Voltage Differential Signaling) to interface, +12V of DC supply voltages.
www.panelook.com
LD-K23453-1
hin Film
TFT LCD Panel
(1920 x RGB x 1080)
Open Cell [LK600D3HA19]
Gate Drive
Source Drive
Source PWB (S-PWB)
SS-FPC
CS-FPC [LK0DZ1C0xxx
CN101
Control PWB (C-PWB) [LK0DZ1C0xxx]
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
r
m
r
3. Mechanical Specifications
Paramete
Specifications Unit
Display size
Active area 1329.12(H) x 747.63 (V) mm
Pixel Format
Pixel pitch 0.69225(H) x 0.69225 (V) mm Pixel configuration R, G, B vertical stripe Display mode Normally black Open Cell Outline Dimensions [Note1] Mass
Surface treatment [Note2]
[Note1] Outline dimensions are shown in P17. [Note2] With the protection film removed.
4. Open Cell Driving Specifications
4.1. Driving interface of C-PWB SHARP specifies [LK0DZ1C0xxx]
CN1: Power and LVDS data input
- Using connector:
Matching connector : FI-RE51HL, FI-RE51CL (Japan Aviation Electronics Ind., Ltd.) or equivalent
-
device
- Mating LVDS transmitter: THC63LVD1023 or equivalent device
Pin No. Symbol Function Remark
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
GND Reserved Reserved Reserved Reserved Reserved
SELLVDS
Reserved Reserved Reserved It is required to set non-connection(OPEN)
GND
AIN0- Aport (-)LVDS CH0 differential data input
AIN0+ Aport (+)LVDS CH0 differential data input
AIN1- Aport (-)LVDS CH1 differential data input
AIN1+ Aport (+)LVDS CH1 differential data input
AIN2- Aport (-)LVDS CH2 differential data input
AIN2+ Aport (+)LVDS CH2 differential data input
GND
ACK- Aport LVDS Clock signal(-)
ACK+ Aport LVDS Clock signal(+)
GND
AIN3- Aport (-)LVDS CH3 differential data input
AIN3+ Aport (+)LVDS CH3 differential data input
FI-RE51S-HF (Japan Aviation Electronics Ind., Ltd.)
It is required to set non-connection(OPEN) It is required to set non-connection(OPEN) It is required to set non-connection(OPEN) It is required to set non-connection(OPEN) It is required to set non-connection(OPEN) Select LVDS data order [Note1,2] It is required to set non-connection(OPEN) It is required to set non-connection(OPEN)
www.panelook.com
152.496 (Diagonal) c
60.0 (Diagonal) inch
1920(H) x 1080(V) (1pixel = R + G + B dot)
1364.18(W) x 806.05(H) x 3.5(D)
4.2
r
0.3
- Front polarize Hard coating: 2H and more
- Rear polarizer : Hard coating less
: Anti Glare, Low Haze
Pull up : (3.3V)
LD-K23453-2
pixel
mm
kg
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
AIN4- Aport (-)LVDS CH4 differential data input
AIN4+ Aport (+)LVDS CH4 differential data input
GND GND
BIN0- Bport (-)LVDS CH0 differential data input
BIN0+ Bport (+)LVDS CH0 differential data input
BIN1- Bport (-)LVDS CH1 differential data input
BIN1+ Bport (+)LVDS CH1 differential data input
BIN2- Bport (-)LVDS CH2 differential data input
BIN2+ Bport (+)LVDS CH2 differential data input
GND
BCK- Bport LVDS Clock signal(-)
BCK+ Bport LVDS Clock signal(+)
GND
BIN3- Bport (-)LVDS CH3 differential data input
BIN3+ Bport (+)LVDS CH3 differential data input
BIN4- Bport (-)LVDS CH4 differential data input
BIN4+ Bport (+)LVDS CH4 differential data input
GND GND GND GND GND VCC +12V Power Supply VCC +12V Power Supply VCC +12V Power Supply VCC +12V Power Supply VCC +12V Power Supply
[Note] GND of a liquid crystal panel drive part should be connected with a module chassis.
[Note1] The equivalent circuit figure of the terminal.
www.panelook.com
LD-K23453-3
3.3V
100ohm
Ter mi na l
10kohm
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
[Note2] LVDS Data order
Data
TA0 TA1 TA2 TA3 TA4 TA5 TA6 TB0 TB1 TB2 TB3 TB4 TB5 TB6 TC0 TC1 TC2 TC3 TC4 NA NA TC5 NA NA TC6 DE(*) DE(*) TD0 TD1 TD2 TD3 TD4 TD5 TD6
TE0 TE1 TE2 TE3 TE4 TE5 TE6
NA: Not Available (*)Since the display position is prescribed by the rise of DE(Display Enable)signal, please do not fix DE signal during operation at ”High”.
L(GND) [VESA]
R0(LSB) R1 R2 R3 R4 R5 G0(LSB) G1 G2 G3 G4 G5 B0(LSB) B1 B2 B3 B4 B5
R6 R7 G6 G7 B6 B7 N/A R8 R9(MSB) G8 G9(MSB) B8 B9(MSB) N/A
www.panelook.com
LD-K23453-4
SELLVDS
H(3.3V) or Open
[JEIDA] R4 R5 R6 R7 R8 R9(MSB) G4 G5 G6 G7 G8 G9(MSB) B4 B5 B6 B7 B8 B9(MSB)
R2 R3 G2 G3 B2 B3 N/A R0(LSB) R1 G0(LSB) G1 B0(LSB) B1 N/A
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
NAN
N
N
N
N
NAN
N
N
N
N
LVDS_SEL = Low (GND)
ACK+, BCK+
, BCK
ACK
www.panelook.com
LD-K23453-5
1cycle
AIN0+, BIN0+
AIN0–, BIN0–
AIN1+, BIN1+
AIN1–, BIN1–
AIN2+, BIN2+
R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
B3 B6 DE
AIN2–, BIN2–
AIN3+, BIN3+
AIN3–, BIN3–
AIN4+, BIN4+
AIN4–, BIN4–
R7 R6
R9 R8
LVDS_SEL = High (3.3V) or OPEN
A B5 B4 B3 B2 DE
A B7 B6 G7 G6 R7 R6
A B9 B8 G9 G8 R9 R8
A
A
1cycle
ACK+, BCK+
ACK
, BCK
AIN0+, BIN0+
AIN0–, BIN0–
AIN1+, BIN1+
AIN1–, BIN1–
AIN2+, BIN2+
R5 R4 G4 R9 R8 R7 R6 R5 R4 G4
G6 G5 B5 B4 G9 G8 G7 G6 G5 B5
B7 B6 DE
AIN2–, BIN2–
AIN3+, BIN3+
AIN3–, BIN3–
AIN4+, BIN4+
AIN4–, BIN4–
R3 R2
R1 R0
A B3 B2 G3 G2 R3 R2
A B1 B0 G1 G0 R1 R0
DE: Display Enable, NA: Not Available (Fixed Low)
A B9 B8 B7 B6 DE
A
A
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4.2. Vcom adjustment
For the prevention of long-time image sticking of TFT-LCD panel, be sure to adjust Vcom in such as a way
that flicker is minimum on the center of display by visual or flicker meter.
- Vcom IC: ISL45041 controlled from CN103. [Note]
- Adjustment pattern :
www.panelook.com
LD-K23453-6
V0
V512V0V512V0V512V0V512
V512V0V512V0V512V0V512V0V512
V0
V512V0V512V0V512V0V512
1 pixel
1 dot
[Note] Interface to adjust Vcom
Using Via Hole : 1.5mm Pitch (
Mating connector : (housing) 5P-SZN, (contact)SZN-002T-P0.7K (JST Co.,Ltd.)
Communication method㻌㻌 㻌㻌:
Pin No. symbol Function Remark
1 SCL I2C CLK 2 SDA I2C DATA 3 - - 4 - - 5 GND Ground
4.3. Absolute maximum ratings
Parameter Symbol Condition Ratings Unit Remark
Input voltage
12V supply voltage
V
VCC
V0
V0
I
Ta=25qC Ta=25qC
I
0.7mm )
I2C
TBD
-0.3 ~ 3.6 V [Note 1] 0 ~ +14 V
Storage temperature Tstg - -25 ~ +60
Operation temperature
Topa - 0 ~ +50
qC
qC
[Note 2]
[Note1] Applies to the input signals to C-PWB.
SELLVDS
[Note2]
- Humidity: 95%RH Max.(Ta < 40qC)
- Maximum wet-bulb temperature at 39
o
C or less. (Ta > 40qC)
- No condensation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4.4. Electrical characteristics of input signals
Parameter Symbol Min. Typ. Max. Unit Remark
Current dissipation Icc - TBD TBD A [Note2]
+12V supply voltage
Permissible input ripple voltage VRP - - 100 mVP-P Vcc = +12.0V
Input Low voltage VIL 0 - 0.7 V
Input High voltage VIH 2.3 - 3.3 V
Input leak current (Low)
Input leak current (High)
Terminal resistor RT - 100 - ohm Differential input
Input Differential voltage |VID| 200 400 600 mV [Note5]
Differential input
common mode voltage
[Note] VCM: Common mode voltage of LVDS driver.
[Note1]
Input voltage sequences
50us < t1 < 20ms
20ms < t2 < 5s
20ms < t3 < 5s
0 < t4 < 1s
1s < t5-1
1s < t5-2
0 < t6 -1
0 < t6 -2
1s < t7
0.9Vcc
0. 1Vc c
Vcc
t1
Data1
t3
Data2
t5-2
Back light:V
t2
t5-1
ON
OFF
ON
ON
ON t6-2
Data1: ACKr, AIN0r, AIN1r, AIN2r, AIN3r, AIN4r, BCKr, BIN0r, BIN1r, BIN2r, BIN3r, BIN4r
*VCM voltage pursues the sequence mentioned above.
www.panelook.com
LD-K23453-7
Ta=25qC
Supply voltage Vcc 11.4 12 12.6 V [Note1]
t1=500μs
V
V
Vcc
V1= 10.8V
V2=9.1V
[Note6]
[Note3]
I = 0V
V
I = 0V
V
[Note 4]
I = 3.3V
I = 3.3V
[Note 4]
Inrush current
t4
t3
6-1
1- TBD - A
I
RUSH
I
2- TBD - A t1>5ms
RUSH
I
IL1 - - 400 μA
IIL2 - - 100 μA
I
IH1 - - 100 μA
IIH2 - - 400 μA
|VID|/2 1.2 2.4-|VID|/2 V [Note5]
V
CM
Dip conditions for supply voltage
a) V2 <
Vcc < V1
td < 10ms
b) Vcc < V2
This case is based on input voltage sequences.
0.9Vcc
0. 1Vcc 0.1V cc
t7
OFF
td
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
Data2: SELLVDS
[Note] About the relation between data input and back light lighting, please base on the above-
mentioned input sequence. When back light is switched on before panel operation or after a
panel operation stop, it may not display normally. But this phenomenon is not based on change
of an incoming signal, and does not give damage to a liquid crystal display.
[Note2] Typical current situation: 1024 gray-bar patterns. (Vcc = +12.0V)
The explanation of RGB gray scale is seen in section 4.8.
RGB
GS0
RGB
GS1
RG B
GS2
[Note3] SELLVDS
[Note4] SELLVDS
[Note5] LVDS differential data and Clock signal (AIN0a4r, BIN0a4r, ACKr, BCKr)
CH*_CLK-,
CH*_Data-
CH*_CLK+,
CH*_Data+
GND
[Note6] Vcc12V inrush current waveform
TBD
www.panelook.com
RG B
....
GS 1022
RGB
G S1023
|VID|
LD-K23453-8
Vcc = +12.0V
1/Tc = 74.25MHz
TH = 14.8s
TV = 60Hz
|VID|
VCM
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4.5. Timing characteristics of input signals
Timing diagrams of input signal are shown in below figure.
Parameter Symbol Min. Typ. Max. Unit Remark
www.panelook.com
LD-K23453-9
Clock Frequency 1/Tc 67 74.25
1100
14.8
960
1125
60
Data
Enable
Signal
Horizontal period TH
Horizontal period
(High)
THd
Vertical period TV
Vertical period
(High)
TVd 1080 1080 1080 line
1050
14.2
960
1109
47
76
1300
16.1
960
1400
61
MHz clock
μs
clock
line
Hz
[Note]
-
When vertical period is very long, flicker and etc. may occur.
-
Please turn off the module after it shows the black screen.
-
Please make sure that length of vertical period should become of an integral multiple of horizontal
length of period. Otherwise, the screen may not display properly.
-
As for your final setting of driving timing, we will conduct operation check test at our side, please
inform your final setting.
TH
THd
DE
A port Data (R G, B)
B port Data (R, G, B)
DE
1919
1920
Tc
1 3
2
Timing diagram of input signal
4
TV
1917
1918
1 2 1079 1080
1919
1920
TVd
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4.6. Input data signal and display position on the screen
B1 G1 R1 B2 G2 R2
(1,1) (1,2)
B3 G3 R3 B4 G4 R4
(13)
www.panelook.com
LD-K23453-10
(1,4)
1,1 1,2 1,3
2,1 2,2
3,1
1,4
SHARP
1080,1
S-PWB
[Note] Scan direction is setting for using S-PWBs’ side down.
4.7. LVDS signal characteristics
CLK-
CLK+ Data*-
Data*+
tpd0
tpd1 tpd2 tpd3 tpd4 tpd5 tpd6
Item Symbol Min. Typ. Max. Unit
Delay time, CLK rising edge to serial bit position 0 Delay time, CLK rising edge to serial bit position 1 Delay time, CLK rising edge to serial bit position 2
Data position
Delay time, CLK rising edge to serial bit position 3 Delay time, CLK rising edge to serial bit position 4 Delay time, CLK rising edge to serial bit position 5 Delay time, CLK rising edge to serial bit position 6
1,1920
1080,1920
S-PWB S-PWB S-PWB
t
CLK
Vdiff=0V Vdiff=0V
tpd0 -0.25 0 0.25
tpd1
tpd2
tpd3
tpd4
tpd5
tpd6
1*t
2*t
3*t
4*t
5*t
6*t
CLK
CLK
CLK
CLK
CLK
CLK
/7-0.25 1*t
/7-0.25 2*t
/7-0.25 3*t
/7-0.25 4*t
/7-0.25 5*t
7-0.25 6*t
CLK
CLK
CLK
CLK
CLK
CLK
/7 1*t
/7 2*t
/7 3*t
/7 4*t
/7 5*t
/7 6*t
CLK
CLK
CLK
CLK
CLK
CLK
/7+0.25
/7+0.25
/7+0.25
/7+0.25
/7+0.25
/7+0.25
ns
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
4.8. Input signal, basic display colors and gray scale of each color
Colors & Gray Scale
Basic Color Black 0 000000000000000000 0 0 0 0 0 0 00000 Blue 0 000000000000000000 0 1 1 1 1 1 11111 Green 0 000000000111111111 1 0 0 0 0 0 00000 Cyan 0 000000000111111111 1 1 1 1 1 1 11111 Red 1 111111111000000000 0 0 0 0 0 0 00000 Magenta – 1 111111111000000000 0 1 1 1 1 1 11111 Yellow 1 111111111111111111 1 0 0 0 0 0 00000 White 1 111111111111111111 1 1 1 1 1 1 11111 Gray Scale of Red Black GS0 0 000000000000000000 0 0 0 0 0 0 00000
--- GS1 1 000000000000000000 0 0 0 0 0 0 00000
--- GS2 0 100000000000000000 0 0 0 0 0 0 00000
--- ---
--- ---
--- GS1021 1 011111111000000000 0 0 0 0 0 0 00000
--- GS1022 0 111111111000000000 0 0 0 0 0 0 00000 Red GS10231 111111111000000000 0 0 0 0 0 0 00000 Gray Scale of Green Black GS0 0 000000000000000000 0 0 0 0 0 0 00000
--- GS1 0 000000000100000000 0 0 0 0 0 0 00000
--- GS2 0 000000000010000000 0 0 0 0 0 0 00000
--- ---
--- ---
--- GS1021 0 000000000101111111 1 0 0 0 0 0 00000
--- GS1022 0 000000000011111111 1 0 0 0 0 0 00000 Green GS10230 000000000111111111 1 0 0 0 0 0 00000 Gray Scale of Blue Black GS0 0 000000000000000000 0 0 0 0 0 0 00000
--- GS1 0 000000000000000000 0 1 0 0 0 0 00000
--- GS2 0 000000000000000000 0 0 1 0 0 0 00000
--- ---
--- ---
--- GS1021 0 000000000000000000 0 1 0 1 1 1 11111
--- GS1022 0 000000000000000000 0 0 1 1 1 1 11111 Blue GS10230 000000000000000000 0 1 1 1 1 1 11111
-
0: Low level voltage / 1: High level voltage
-
Each basic color can be displayed in 1024 gray scales from 10 bits data signals. According to the
combination of total 30 bits data signals, one billion-color display can be achieved on the screen.
www.panelook.com
LD-K23453-11
Data signal
R0 R1 R2 R3 R4 R5 R6 R7 R8 R9G0 G1 G2G3 G4 G5G6 G7G8 G9B0 B1 B2 B3 B4 B5B6 B7 B8 B9
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
5. Optical
characteristics
Parameter Symbol Condition Min. Typ. Max. Unit Remark
Horizontal
Viewing
angle range
Vertical
Contrast ratio CRn
Response time
White
Red
Chromaticity
Green
Blue
Luminance White YL Luminance
uniformity
White
- Optical characteristics are based on SHARP standard CCFL module’s backlight system such as
LK600D3LA38B.
- Measurement condition: Set the value of V
- The measurement shall be executed 60 minutes after lighting at rating.
[Note] The optical characteristics are measured using the following equipment.
www.panelook.com
Ta=25qC, Vcc=12.0V, V
T T
T T
W
21 22
11 12
DRV
x y x y x y x y
Gw
10
CR>
T
=0 deg.
to maximum luminance of white.
BRT
LD-K23453-12
=24.0V, V
INV
70 88 - Deg.
=100%, Timing: 120Hz (typ. value)
BRT
[Note1,4]
70 88 - Deg.
3500 5000 - - [Note2,4]
- 4 - ms [Note3,4,5] (0.250) (0.280) (0.310) (0.255) (0.285) (0.315) (0.616) (0.646) (0.676) (0.307) (0.337) (0.367) (0.251) (0.281) (0.311) (0.577) (0.607) (0.637) (0.113) (0.143) (0.173) (0.041) (0.071) (0.101)
400 500 -
1.6
-
-
-
-
-
[Note4]
-
-
-
cd/m2
[Note6]
Detector (EZ-CONTRAST/Photodiode)
Middle of the screen (T䠙0q)
TFT-LCD Module
Measurement of viewing angle range and Response time.
-Viewing angle range: EZ-CONTRAST
- Response time: Photodiode
[Note1] Definitions of viewing angle range:
Normal line
T
T
22
T
12
11
Detector (SR-3A-L1)
400mm
Field=1q
Middle of the screen (T䠙0q)
TFT-LCD Module
Measurement of Contrast, Luminance, Chromaticity.
T
21
6 o’clock direction
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
[Note2] Definition of contrast ratio:
The contrast ratio is defined as the following.
[Note3] Definition of response time
The response time (W
switching the input signal for “any level of gray (0%, 25%, 50%, 75% and 100%)” and “any level
of gray (0%, 25%, 50%, 75% and 100%)”.
0% 25% 50% 75% 100%
www.panelook.com
LD-K23453-13
=RatioContrast
and Wr) is defined as the following figure and shall be measured by
d
whitepixels all with s)(brightnes Luminance
black pixels all with s)(brightnes Luminance
0%
25%
50%
75%
100%
tr: 0%-25% tr: 0%-50% tr: 0%-75% tr: 0%-100%
td: 25%-0% tr: 25%-50% tr: 25%-75% tr: 25%-100%
td: 50%-0% td: 50%-25% tr: 50%-75% tr: 50%-100%
td: 75%-0% td: 75%-25% td: 75%-50% tr: 75%-100%
td: 100%-0% td: 100%-25% td: 100%-50% td:100%-75%
t*:x-y --- response time from level of gray(x) to level of gray(y)
,
W
¦
r
100%
90%
10%
0%
Photo detector Output
(Relative Value)
10y)-x:tr(
W
¦
d
W
d
yxtd
Dark
10):(
BrightBright
W
r
Time
[Note4] This value shall be measured at center of the screen.
[Note5] This value is valid when O/S driving is used at typical input time value.
[Note6] This value is calculated as the following with nine measurements. (AaE)
w
G
s)(brightnes points five of luminance Minimum
s)(brightnes points five of luminance Maximum
480 960 1440
A
C
B
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
pixel
D
E
270 540
810 pixel
www.panelook.com
Global LCD Panel Exchange Center
Q
y
6. Packing for shipping
6.1. Packing form
a) Open Cell quantity in 1 cell box : 20 cells
b) Piling number of cell box : 4 Maximum
c) 1 palette size : 1600(W) x 1000(D) x 889(H) [mm]
d) Total mass of 1 palette filled with full open cells : (392)kg Maximum
[Note] Please refer to the attached drawing for details. (P18)
6.2. Label
a) Open Cell Label
This label is stuck on the protection film of front polarizer.
www.panelook.com
LD-K23453-14
ex) LK600D3HA19
LK600D3HA19
䠏䠓䠌䠠䠏䠨
0Y F 00001 J
䠑䠕䚷䠴䠴䠴䠴
䠩䠝䠠䠡䚷䠝䠬䠝
2D Barcode
How to express Lot No.
O O O O O O O O
O
Suffix code
Production plant [Note1]
Production month (1~9,X,Y,Z)
Production year (the last figures of the Christian Era)
Serial No.
b) Packing label
This label is stuck on the cell box and palette.
ex) LK600D 3HA 19
♫ෆရ␒
㻸㼛㼠㻺㻻 㻚
(4S)㻌㻸㻷㻢㻜㻜㻰㻟㻴㻭㻝㻥
㻮㼍㼞㼏㼛㼐㼑䠄䐟䠅
( 1T)
㻮㼍㼞㼏㼛㼐㼑䠄䐠䠅
Model No.
Barcode (Serial No.)
Lot No.
[Note1] Production plant code
Code Plant Model No. & Suffix Code
K, L Japan LK600D3HA19
ձ Model No.& Suffix Code
ղ Lot No.
ճ
uantit
㻽㼡㼍㼚㼠㼕㼠㼥
㻮㼍 㼞㼏㼛 㼐㼑 䠄 䐡䠅
䝴䞊䝄ရ␒
䝅䝱䞊䝥≀ὶ⏝䝷䝧䝹䛷䛩䚹
(Q)㻌㻌㻌㻌㻌㻌㻌㻌㻌㻌㻌pcs
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
7. Reliability test item
No. Test item Condition
High temperature storage test
1
Low temperature storage test
2
(Open Cell)
(Open Cell)
High temperature and
3
high humidity operation test
(Open Cell)
High temperature operation test
4
Low temperature operation test
5
(Open Cell)
(Open Cell)
Vibration test
6
(Cell Box with full Open Cells)
7
(Cell Box with full Open Cells)
Drop test
[Result evaluation criteria]
Under the display quality test condition with normal operation state, there shall be no change, which
may affect practical display function.
8. Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the module and cabinet so that the Open Cell can be installed without any extra
stress such as warp or twist.
c) Since the polarizer is easily damaged, pay attention not to scratch it.
d) Since long contact with water may cause discoloration or spots, wipe off water drop immediately.
e) When the polarizer is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle
with care.
g) Precautions of peeling off the protection film.
www.panelook.com
LD-K23453-15
Ta = 60qC 240h
Ta = -25qC 240h
Ta = 40qC 95%RH 240h (No condensation)
Ta = 50qC 240h
Ta = 0qC 240h
X and Y direction: 15min, Z direction: 60min. 5Hz to 50Hz acceleration velocity: 1.0G Sweeping ratio: 3min Height: 25cm (corner and edge), 32cm (surface) Number: 8times
(corner 1time and edge 3times and
surface 4times)
- Be sure to peel off slowly (recommended more than 7sec) and constant speed.
- Peeling direction shows Fig.
- Be sure to ground person with adequate methods such as the anti-static wrist band.
- Be sure to ground S-PWB while peeling of the protection film.
- Ionized air should be blown over during peeling action.
- The protection film must not touch drivers and S-PWBs.
- If adhesive may remain on the polarizer after the protection film peeling off, please remove with isopropyl-alcohol.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
h) Since the Open Cell consists of TFT and electronic circuits with CMOS-ICs, which are very weak to
electrostatic discharges, persons who are handling the Open Cell should be grounded through
adequate methods such as the anti-static wrist band. Connector pins should not be touched directly
with bare hands.
- Reference : Process control standard of sharp Item Management standard value and performance standard 1 Anti-static mat (shelf) 1 to 50 [M ohm]
2 Anti-static mat (floor, desk) 1 to 100 [M ohm] 3 Ionizer 4 Anti-static wrist band 0.8 to 10 [M ohm] 5 Anti-static wrist band entry and
ground resistance 6 Temperature 7 Humidity 60 to 70 [%RH]
i) The Open Cell has some PWBs, take care to keep them from any stress or pressure when handling or
installing the Open Cell, otherwise some of electronic parts on the PWBs may be damaged.
j) When handling the Open Cell and assembling them into module and cabinets, please be noted that
long-term storage in the environment of oxidization or deoxidization gas and the use of such
materials as reagent, solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion
and discoloration of the Open Cell.
k) Applying too much force and stress to PWB and driver (COF) may cause a malfunction electrically
and mechanically.
l) The Open Cell has high frequency circuits. Sufficient suppression to EMI should be done by system
manufacturers.
m) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.
n) The chemical compound, which causes the destruction of ozone layer, is not used.
o) This Open Cell is corresponded to RoHS. ‘‘R.C.’’ label on the side of palette shows it.
p) When any question or issue occurs, it shall be solved by mutual discussion.
9. Carton storage condition
Temperature Humidity 95% RH or less Reference condition
Sunlight Be sure to shelter a production from the direct sunlight. Atmosphere
Notes
Storage life 1 year.
www.panelook.com
LD-K23453-16
Attenuate from
Below 1000 [ohm]
22 to 26 [qC]
0qC to 40qC
20qC to 35qC, 85% RH or less (summer) 5qC to 15qC, 85% RH or less (winter) the total storage time (40qC, 95% RH) : 240h or less
Harmful gas, such as acid and alkali which bites electronic components and/or wires must not be detected. Be sure to put cartons on palette or base, don’t put it on floor, and store them with removing from wall. Please take care of ventilation in storehouse and around cartons, and control changing temperature is within limits of natural environment.
r
1000V to r100V within 2 sec
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
LD-K23453-17
www.panelook.com
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
Outline of Open Cell
www.panelook.com
Global LCD Panel Exchange Center
LD-K23453-18
Top Sheet
www.panelook.com
Bottom Base
Palette
Side Frame
1 Palette
PP Band
: 4pcs
1 Cell Box
Drawing of Packing
Packing Label
R.C.Label
Open Cell
:20cells
Cell Box (Top)
Protective Sheet
: 21pcs
Cell Box (Bottom)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Loading...