Sharp LC-32CFG6241KF, LC-32CFG6242KF, LC-32CHG6241KF, LC-32CHG6242KF, LC-40CFG6241KF Quick Start Manual

2. Using the RF cable supplied, connect the TV to the

TV Aerial wall socket. Connect the power cable to
the electrical outlet.

3. The TV should power on automatically once the TV

is connected to the mains. In the event this does
not happen, please refer to the ‘Pairing the remote
control’ section of the QSG.

4. Insert the batteries supplied into the remote

control. The remote control should automatically
be paired with the TV set. If this is not the case,
please refer to the ‘Pairing the remote control’
section of the QSG.

6. If the TV  nds some, but not all of the channels you would expect to receive, the signal

being received by the TV is inadequate. In most circumstances this can be corrected with
the simple addition of a Signal Booster between the TV and the TV aerial wall socket, as
shown. Once the signal booster is connected, retune the TV in order to receive all of the
channels.

5. You will be welcomed with the  rst time installation screen. Select your

chosen options and press OK on the remote control and tuning will begin.

1. ( g.1) Place the TV set on a  at and clean surface with the panel facing downwards to avoid damage, then  x the stand/feet shown. The feet are marked L (left) and R (right). ( g.2) When the stand feet are installed correctly, the

stand/feet will be angled away from each other at the front of the TV set. ( g.3) Secure the stand/feet to the underside of the TV set using the 4 screws provided.

QUICK START GUIDE

Quick Start Set Up Guide. For full instructions please refer to the user guide (available to download from the website).

Hotline: UK. 0330 024 0803 ROI. 01443 3940 | Internet: www.umc-uk.co.uk
Model Number: LC-32CFG6241KF, LC-32CFG6242KF, LC-32CHG6241KF, LC-32CHG6242KF, LC-40CFG6241KF, LC-40CFG6242KF, LC-43CFG6241KF, LC-43CFG6242KF,

LC-49CFG6241KF, LC-49CFG6242KF, LC-55CFG6241KF, LC-55CFG6242KF

UK: Calls are charged at your normal telephone call rate. ROI: Calls are charged at a local rate.

SHA/QSG/0073

Standby Button

Used for attaching the stand
to the TV set ( g.2)

4 x

For stand/feet installation, there is one type of screw
provided as shown below.

To complete the stand installation you will require a
cross head screw driver.

Place the TV set on a  at and clean surface with the
panel facing downwards to avoid damage.

L

R

1

TV panel must be facing downwards.

4 x

3
4

1

2

L

R

3

TV panel must be facing downwards.

2

TV panel must be facing downwards.

To receive Freeview channels, in particular Freeview HD channels,
you will need a Digital TV aerial and be in a good Freeview
coverage area. You can check coverage for your postcode
at www.freeview.co.uk.

Please note that any Freeview HD channels found during tuning
will be placed in channel positions above 100.
For example, 101 (BBC1 HD) 102 (BBC2 HD) etc.

Pairing the remote control

1) If the TV turns on automatically and the  rst time installation
screen appears but the TV does not react to remote control, press
and hold the centre two coloured buttons at the bottom
of the remote control for a few seconds. The power light will blink 5
times to con rm the TV and remote control are paired.

2) If the TV does not automatically turn on you will need to turn
the TV on using the standby button on the TV set (not the remote
control), once switched on, press the standby button on the TV set
once, this will prompt the ‘pairing menu’ to appear, scroll through
and highlight ‘Pair your remote’ by pressing the CH+/CH- TV button
(scroll up/down function in the menu) then press the TV set’s
standby button (OK function in the menu) to con rm your selec­tion, then with the remote control, press and hold the centre two
coloured buttons at the bottom of the remote control a few seconds,
the power light will blink 5 times to con rm the TV and remote
control are paired.

GOTO A-B ANGLE

REPEAT

REC
LIST

NOTE: In Home Mode, the TV will switch itself to Standby mode after 4-5 hours in the event that
the TV buttons or remote control buttons are not pressed.

HOME MODE is the mode for end users, by default

it is set to a power saving mode which reduces the
energy used by up to 25% (by reducing the power
to the LED/LCD panel). This can be changed in the
picture mode settings in the TV operation menu.

When in STORE MODE the picture is adjusted to
a brighter setting. The shop demonstration will
appear on the screen automatically after 2 minutes.

Sharp - SHA-QSG-0073 - QSG - SmartTV - G6242KF series.indd 1Sharp - SHA-QSG-0073 - QSG - SmartTV - G6242KF series.indd 1 27/02/2018 14:31:3527/02/2018 14:31:35