The maximum output voltage for the music player
function, measured in accordance with EN 50332-2, is
32.0 mV.
はじめに
9
Quick Manual
EN60825-1:1994 A1:2002 & A2:2001
CLASS1
LED Product
CAUTION
Use only the battery packs and adapters specified
by NTT DOCOMO for use with the FOMA terminal.
May cause fires, burns, bodily injury or electric shock.
Do not throw the battery pack into a fire.
The battery pack may catch fire, explode, overheat or
leak.
Do not dispose of used battery packs in ordinary
garbage.
May cause fires or damage to the environment. Place
tape over the terminals to insulate unnecessary battery
packs, and take them to a docomo Shop, retailer or
institution that handles used batteries in your area.
Avoid using the handset in extremely high or low
temperatures.
Use the FOMA terminal within the range of a
temperature between 5°C and 40°C (for temperatures
of 36°C or higher, such as in a room with a bath, limit
usage to a short period of time) and a humidity between
45% and 85%.
Charge battery in areas where ambient temperature
is between 5°C and 35°C.
Do not point the illuminated light directly at
someone’s eyes. Especially when you shoot still
pictures or moving pictures of young children, keep
1 m or more distance from them.
Do not use Picture Light near people’s faces. Eyesight
may be temporarily affected leading to accidents.
Picture Light
CAUTION:
Use of controls, adjustments or performance of
procedure other than those specified herein may result
in hazardous radiation exposure. As the emission level
from Picture Light LED used in this product is harmful to
the eyes, do not attempt to disassemble the cabinet.
Servicing is limited to qualified servicing station only.
Picture light source LED characteristics
a) Continuous illumination
b) Wavelength
White: 400-700 nm
c) Maximum output
White: 208 μW (inside FOMA terminal 0.62 mW)
その他
101
Before Using
Notch
IC (gold)
Tabs
With a recycle mark
side up
Inserting UIM
1 Hook a finger on the tab and pull out the tray (1)
Pull out the tray straight until it stops.
2 Hold the UIM with the IC
(gold) side turned down
and set on the tray (2)
3 Push the tray all the way in (3)
Tray
Attaching battery pack
Perform with the FOMA terminal turned off and
closed while holding with your both hands.
The battery pack is not waterproof/dust-proof.
1 Slide the back cover lever in the direction of the
arrow (1) to unlock and remove the back cover
(2)
The FOMA terminal has a slot to remove the
back cover. Securely hold the FOMA terminal as
shown in the illustration to prevent excessive
force on the back cover and hook a nail on the
slot and remove the back cover upward.
Tab
Note that inserting or removing the UIM forcibly
may damage the UIM or deform the tray.
その他
102
Notch
Slot
2 Attach the battery
pack
Turn a recycle
mark side of the
battery pack up,
match tabs and
attach the
battery pack.
3 Insert the tab of the top of the back cover into
Back cover
Securely push
tab areas down
with both hands
the FOMA terminal slot (1), attach it in the
direction of the arrow (2) and securely push
down with both hands (3)
The back of the back cover has also five tabs to
insert the back cover. Securely push tab areas
down with both hands so that gaps are not left
between the FOMA terminal and the back cover.
4 Slide the back cover lever in the direction of the
arrow (4) to lock
Lever
Using unnecessary force when attaching or
removing the battery pack may damage the
connector terminal for the battery pack (charger
terminal) on the FOMA terminal.
Securely close the back cover. If not closed
securely, the back cover may come off and the
battery pack may fall out due to vibration. May
damage the waterproof/dust-proof performance
and allow water to seep or dust to get in.
Charging
It is recommended that the accompanying desktop
holder be used for charging to prevent water from
seeping or dust from getting in caused by forgetting
to close the external connector terminal cover.
The AC adapter and desktop holder are not
waterproof/dust-proof. Never try to charge the
battery pack when the FOMA terminal is wet.
1 Turn the arrow side of the AC adapter connector
up and insert it into the connector terminal of the
desktop holder (1)
Keep the connector parallel with the desktop
holder and securely push all the way in until it
clicks.
2 Insert the AC adapter power plug into an outlet
(2)
その他
103
3 When placing the FOMA terminal in the desktop
Key illustrations may look different from actual keys.
holder, charge alert is heard, charging LED
illuminates, and charging starts
Place the FOMA terminal in the direction of the
arrow until it clicks (3).
Connector (with
Charging LED
4 Charging is complete when charge alert is heard
and charging LED turns off
Hold the desktop holder, flip the FOMA terminal
forward and lift it out.
Pull the AC adapter out of the outlet when left
unused for a long period of time.
When charge alert is not heard or when charging
LED does not illuminate, check that the FOMA
terminal is placed securely in the desktop holder
(except when terminal is turned off, manner mode
is set or charge alert is [OFF]).
When placing the FOMA terminal in the desktop
holder, be careful not to catch a strap, etc.
the arrow side up)
100V AC
outlet
FOMA AC
Adapter 01/02
Part Names and Functions
その他
104
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.