The maximum output voltage for the music
player function, measured in accordance with
EN 50332-2, is 28.0 mV.
心臓の弱い方は、着信バイブレー
タ(振動)や着信音量の設定に注意
してください。
心臓に悪影響を及ぼす原因となります。
は
じ
め
に
運転の妨げとなり、事故の原因となります。
9
Quick Manual
EN60825-1:1994 A1:2002 & A2:2001
CLASS1
LED Product
Picture Light
Notch
IC (gold)
123
Notch
Tray
Tab
Use only the battery packs and adapters specified by NTT DOCOMO for use
with the FOMA terminal.
May cause fires, burns, bodily injury or electric shock.
Do not throw the battery pack into a fire.
The battery pack may catch fire, explode, overheat or leak.
Do not dispose of used battery packs in ordinary garbage.
May cause fires or damage to the environment. Place tape over the terminals to
insulate unnecessary battery packs, and take them to a docomo Shop, retailer or
institution that handles used batteries in your area.
Avoid using the handset in extremely high or low temperatures.
Use the FOMA terminal within the range of a temperature between 5°C and 40°C
(for temperatures of 36°C or higher, such as i n a room with a bath, lim it usage to a
short period of time) and a humidity between 45% and 85%.
Charge battery in areas where ambient temperature is between 5°C and
35°C.
Do not point the illuminated light directly at someone’s eyes.
Do not use Picture Light near people’s faces. Eyesight may be temporarily
affected leading to accidents.
CAUTION
CAUTION:
Use of controls, adjustments or performance of procedure other than those
specified herein may result in hazardous radiation exposure. As the emission level
from Picture Light LED used in this product is harmful to the eyes, do not attempt
to disassemble the cabinet. Servicing is limited to qualified servicing station on ly.
Picture light source LED characteristics
a) Continuous illumination
b) Wavelength
White: 400-700 nm
c) Maximum output
White: 1.4 mW (inside FOMA terminal 4.3 mW)
Before Use
Inserting UIM (FOMA card)
1 Hook a finger on the tab and pull out the tray (1)
2 Hold the UIM with the IC (gold) turned down and set
on the tray (2)
3 Push the tray all the way in (3)
Note that inserting or removing the UIM forcibly may damage the UIM or
deform the tray.
そ
の
他
105
Attaching battery pack
Slot
Tabs
With a recycle mark
side up
Back cover
Securely push
tab areas down
with both hands
Lever
Perform with the FOMA terminal turned off and closed while holding with your
both hands.
The battery pack is not waterproof/dust-proof.
1 S lide the back cover lever in the direction of the arrow (1) to unlock and
remove the back cover (2)
The FOMA terminal has a slot to remove the back cover. Securely hold the
FOMA terminal as shown in the illustration to prevent excessive force on
the back cover and hook a nail on the slot and remove the back cover
upward.
2 A ttach the battery pack
Turn a recycle mark side of the battery
pack up, match tabs and attach the
battery pack.
そ
の
他
106
3 Insert the tab of the top of the back
cover into the FOMA terminal slot
(1), insert it in the direction of the
arrow (2) and securely push
down with both hands (3)
The back of the back cover has
also six tabs to insert the back
cover. Securely push tab areas
down with both hands so that
gaps are not left between the
FOMA terminal and the back
cover.
4 Slide the back cover lever in the
direction of the arrow (4) to lock
4
Using unnecessary force when attaching or removing the battery pack may
damage the connector terminal for the battery pack (charger terminal) on the
FOMA terminal.
Securely close the back cover. If not closed securely, the back cover may
come off and the battery pack may fall out due to vibration. May damage the
waterproof/dust-proof performance and allow water to seep or dust to get in.
Charging
1
2
Charging LED
Connector (Turn the
side with the arrows up)
FOMA AC
Adapter 01/02
100V AC
outlet
It is recommended that the accompanying desktop holder be used for charging
to prevent water from seeping or dust from getting in caused by forgetting to
close the external connector terminal cover.
The AC adapter and desktop holder are not waterproof/dust-proof. Never try to
charge the battery pack when the FOMA terminal is wet.
1 Turn the side with the arrows of the AC adapter connector up and insert it
into the connector terminal of the desktop holder
Keep the connector parallel with the desktop holder and securely push all
the way in until it clicks.
2 Insert the AC adapter power plug into an outlet
3 When placing the FOMA terminal in the desktop holder, charge alert is
heard, charging LED illuminates, and charging starts
Put the left part of the FOMA terminal on the desktop holder (1) and push
down until it clicks (2).
When charge alert is not heard or when charging LED does not illuminate,
check that the FOMA terminal is placed securely in the desktop holder
(except when terminal is turned off, manner mode is set or charge alert is
[OFF]).
When placing the FOMA terminal in the desktop holder, be careful not to
catch a strap, etc.
When switching to the viewer position with the FOMA terminal set in the
desktop holder, operate with holding the FOMA terminal so that it does not
come off the desktop holder.
4 Charging is complete when charge alert is heard and charging LED turns
off
Hold the desktop holder and lift the FOMA terminal out.
Pull the AC adapter out of the outlet when left unused for a long period of
time.
そ
の
他
107
Loading...
+ 9 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.