Sharp HRO00036 User Manual

Declaration of Conformity

Hereby, Sharp Telecommunications of Europe Ltd, declares that this GX25 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/ EC. A copy of the original declaration of conformity can be found at the following Internet address: http://www.sharp-mobile.com

Introduction

Congratulations and thank you for choosing the GX25.

About This User Guide

This user guide is carefully designed to help you learn about your phone’s features and operations quickly and effectively.

NOTICE

We strongly recommend that you keep separate

• permanent written records of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, we assume no responsibility for data lost or otherwise rendered unusable, whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired or any other cause.

• We assume no responsibility, directly or indirectly, for financial losses or claims from third parties resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss or alteration of stored data, etc.

• All company and/or product names are trademarks and/or registered trademarks of their respective holders.

• Screen layout illustrated in this user guide may differ from the actual one. The information described in this user guide is subject to change without notice.

• All the functions described in this user guide may not be supported in all networks.

• We assume no responsibility for downloaded contents, information, etc. from network.

• Occasionally, a few black or bright pixels may appear on the screen. Please note that this will not have any impact on any of the features or performance.

According to copyright laws, the reproduction, alteration and use of material which is protected by copyright (music, pictures, etc.) is only permitted for personal or private use. If the user is not in possession of more extensive copyright or has not received the explicit permission from the copyright owner to reproduce, alter or use a copy which has been made or modified in this way, this is considered to be a violation of the copyright laws and gives the copyright owner the right to claim for damages. For this reason, avoid the illegal use of material which is protected by copyright.

Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.

Introduction 1

Powered by JBlend™ Copyright 19972004 Aplix Corporation. All rights reserved. JBlend and all JBlend-based trademarks and logos are trademarks or registered trademarks of Aplix Corporation in Japan and other countries.

Licensed by Inter Digital Technology Corporation under one or more of the following United States Patents and/or their domestic or foreign counterparts and other patents pending, including U.S. Patents: 4,675,863: 4,779,262: 4,785,450 & 4,811,420.

Licensed under U.S. Patent 4,558,302 and foreign counterparts.

T9 Text Input is licensed under one or more of the following: U.S. Pat. Nos. 5,818,437, 5,953,541, 5,187,480, 5,945,928, and 6,011,554; Australian Pat. No. 727539; Canadian Pat. No. 1,331,057; United Kingdom Pat. No. 2238414B; Hong Kong Standard Pat. No. HK0940329; Republic of Singapore Pat. No. 51383; Euro. Pat. No. 0 842 463 (96927260.8) DE/ DK, FI, FR, IT, NL,PT.ES,SE,GB; Republic of Korea Pat. Nos. KR201211B1 and KR226206B1; and additional patents are pending worldwide.

is a registered trademark of HI Corpora-

/Micro3D Edition™

2Introduction

Bluetooth is a trademark of the Bluetooth SIG, Inc.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sharp is under license. Other trademarks and trade names are those of their respective owners.

CP8 PATENT

This product is licensed under the MPEG-4 Visual Patent Portfolio License for the personal and non-commercial use of a consumer to (i) encode video in compliance with the MPEG-4 Video Standard (“MPEG-4 Video”) and/or (ii) decode MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a licensed video provider. No license is granted or implied for any other use. Additional information may be obtained from MPEG LA. See http://www.mpegla.com.

This product is licensed under the MPEG-4 Systems Patent Portfolio License for encoding in compliance with the MPEG4 Systems Standard, except that an additional license and payment of royalties are necessary for encoding in connection with (i) data stored or replicated in physical media which is paid for on a title by title basis and/or (ii) data which is paid for on a title by title basis and is transmitted to an end user for permanent storage and/or use. Such additional license may be obtained from MPEG LA, LLC. See http:// www.mpegla.com for additional details.

Useful Functions and Services

Your phone offers you the following features:

• A built-in digital camera for taking pictures and video clips.

• A message function for reading and creating SMS messages.

• MMS (Multimedia Messaging Services) for personalising your phone in various ways.

• A WAP browser for accessing information on the mobile Internet.

• Java™ applications. You can also download various applications from Vodafone via the mobile Internet.

• The external display for quickly checking the information of incoming calls or messages.

• The mobile light with large number of uses: as an auxiliary light for the camera, battery charge notification, incoming call indicator, and makeshift torch.

• E-mail for sending up to 2000 characters and receiving mail with attachments.

• A melody editing function for creating original ringtones using up to 32 voices.

• A voice recorder function for recording and playing back voice clips.

•A Bluetooth

wireless technology interface for establishing contact and transmitting data with certain devices. You can transmit pictures, sounds, and video clips to OBEX-enabled phones.

• An infrared interface for data communication. You can transmit pictures, sounds, and video clips to OBEX-enabled phones.

• A data synchronization function for synchronizing the Contacts List and schedule entries with Microsoft Outlook or Outlook Express on a PC.

• A schedule alarm for creating and sending schedule entries with alarm settings.

Introduction 3

Introduction ................................................. 1

Useful Functions and Services .................... 3

Your Phone .................................................. 7

Optional Accessories ................................... 7

Getting Started ............................................8

Inserting the SIM Card and the Battery .... 11

Charging the Battery ................................. 13

Turning Your Phone On and Off ............... 14

Display Indicators (Main Display) ............ 15

Display Indicators (External Display) ....... 17

Navigating Functions ................................19

Call Functions ............................................20

Making a Call ............................................ 20

Speed Dialling ........................................... 20

Redialling .................................................. 21

Answering a Call ....................................... 21

Incall Menu ............................................... 22

Entering Characters .................................. 26

Changing the Input Languages .................. 27

Changing the Input Method ....................... 27

Using Text Templates ............................... 28

4 Table of Contents

Using the Menu ..........................................29

List of Menu Functions .............................. 30

Contacts List ..............................................32

Selecting the Storage Memory .................. 32

Changing the List Displayed .....................32

Changing the Name Order .........................33

Add New Contact ......................................33

Copying Contacts List Entries between

SIM Card and Handset .............................. 34

Finding a Name and Number ..................... 34

Dialling from the Contacts List .................35

Editing Contacts List Entries .....................35

Deleting Contacts List Entries ...................35

Viewing Groups ......................................... 35

Group Call ................................................. 36

Assigning a Ringtone to Each Contacts

List Entry ...................................................36

Memory Status ...........................................37

Speed Dial List ..........................................37

Sending a Contacts List Entry ................... 37

Receiving a Contacts List Entry ................ 38

Dialling a Service Phone Number ............. 38

Camera ....................................................... 40

Take Picture ...............................................40

Record Video .............................................44

Messages ................................................... 48

Multimedia (MMS) ....................................48

Text (SMS) ................................................53

E-mail ........................................................56

Cell Broadcasts ..........................................58

Vodafone live! ............................................ 59

Starting the WAP Browser ........................59

Navigating a WAP Page ............................60

My Items ..................................................... 63

Pictures ......................................................63

Games & More ...........................................65

Sounds ........................................................66

Videos ........................................................68

Text Templates ..........................................70

Memory Status ...........................................71

Games & More ........................................... 72

Applications ...............................................72

Screensavers ............................................... 73

More Games ............................................... 73

Settings .......................................................74

Java™ Information .....................................75

Applications ...............................................76

SIM Application .........................................76

Alarms ........................................................76

Calculator ...................................................77

Voice Recorder ..........................................78

Melody Editor ............................................79

Phone Help .................................................83

Calendar .....................................................84

Contacts .....................................................87

Call Log ......................................................87

Speed Dial List ...........................................88

My Numbers ..............................................88

Call Timers .................................................88

Data Counter ..............................................88

Call Costs ...................................................89

Settings ......................................................90

Connectivity ...............................................90

Profiles .......................................................93

Setting the Display .....................................99

Sound .......................................................102

Call Settings .............................................102

Table of Contents 5

Date & Time ............................................ 106

Changing the Language ........................... 107

Network ................................................... 107

Security .................................................... 111

Master Reset ............................................ 112

Connecting GX25 to Your PC ................. 113

System Requirements .............................. 113

GSM/GPRS Modem ................................ 113

Handset Manager ..................................... 114

Software Installation ............................... 114

Note ......................................................... 114

Troubleshooting ......................................116

Safety Precautions and Conditions

of Use ....................................................... 118

CONDITIONS OF USE .......................... 118

ENVIRONMENT .................................... 121

PRECAUTIONS CONCERNING

VEHICLE USE ....................................... 121

SAR ......................................................... 122

PRECAUTIONS FOR USE IN USA ...... 122

Index ......................................................... 125

6 Table of Contents

Your Phone

Please check the following carefully. Your phone should come complete with:

• GSM 900/1800/1900 GPRS phone

• Rechargeable Li-ion battery

• AC charger

• Handsfree kit

•CD-ROM

•User guide

• Quick start guide

Optional Accessories

• Li-ion Spare battery (XN-1BT30)

• Cigarette lighter charger (XN-1CL30)

• USB data cable (XN-1DC30)

• AC charger (XN-1QC30, XN-1QC31)

• Personal handsfree kit (XN-1ER20)

The above accessories may not be available in all regions.

For details, please contact your dealer.

Your Phone 7

Getting Started

8 Getting Started

1. Earpiece

2. Navigation Keys (Arrow Keys):

Moves cursor to select menu items, etc.

Up/Down arrow keys: a b

Displays Contacts List entries in standby mode. a and b indicate in this manual these keys.

Left arrow key:

Displays list of Applications in standby mode.

indicates in this manual

this key.

Right arrow key:

Displays list of Saved Pictures in standby mode. d indicates in this manual this key.

3. Left Soft Key:

4. Send Key:

Executes the function at the bottom left of the screen.

Makes or accepts calls, views the call logs in stand-by mode.

5. Centre Key: Displays Main menu in standby mode and executes functions.

6. Voice Mail Key:GPress and hold this key to

connect to the Voice mail centre automatically. (Depends on the SIM card.)

7. */Shift Key:

Switches character case among four modes: Abc, ABC, 123 and abc. Press and hold this key on the text entry screen to shift the text input method between multi-tap and T9 mode.

8. Main Display

9. Right Soft Key:C Executes the function at the

bottom right of the screen. Used to access “Vodafone

live!” by opening the browser in standby mode.

10.End/Power Key:FEnds a call, turns power on/

off.

11.Camera Key: Starts the digital camera in standby mode.

12.Keypad

Getting Started 9

13.#/Silent/Light Key:RSwitches symbol screens.

Press and hold this key on the text entry screen to display the language options screen. Press and hold this key during standby to switch Profiles settings between Normal and Silent mode. Press , then R during standby to turn the Bluetooth wireless func tion on or off.

14.Microphone

15.Self-Portrait Mirror: For taking a self-portrait.

16.Camera

17.Speaker

18.Mobile Light: Used as an auxil iary light in

digital camera/video camera mode, as a battery charge indicator, or notification for incoming calls, data/fax calls or messages.

19.External Display

20.Handsfree Kit Connector

10 Getting Started

21.External Connector:

Used to connect either the charger or USB data cable.

22.RF Connector

23.Battery Cover

24.Built-in Aerial: Warning: Do not cover the

hinge area of the phone with your hand when in use as this may interfere with the performance of the built-in aerial.

25.Side-Up/Side-Down Keys:

V W

Moves cursor to select menu items, adjusts earpiece volume, etc. Press and hold this key during standby to turn the mobile light on or off.

26.Infrared Port: Sends and receives data via infrared.

Inserting the SIM Card and the Battery

1. Slide off the battery cover ( ).

3. Hold the battery so that the metal contacts of the

battery are facing down, slide the guides on the top of the battery into the battery slots , and then insert it .

2. Slide the SIM card into the SIM holder.

4. Replace the battery cover and slide it as shown

below.

SIM card

Note

• Make sure that only 3V SIM cards are used.

• Make sure that the standard accessory battery (XN-1BT30) is used.

Getting Started 11

Removing the SIM Card and the Battery

1. Make sure to turn off your phone and disconnect the

charger and other accessories. Slide off the battery cover ( ).

3. Hold down gently whilst sliding the SIM card

out of the SIM holder .

2. Pick up the battery using the protruding edge and

remove the battery from the phone.

12 Getting Started

Battery Disposal

The device is supported by a battery. In order to protect the environment, please read the following points concerning battery disposal:

• Take the used battery to your local waste depot, dealer or customer service centre for recycling.

• Do not expose the used battery to an open flame, into water or dispose with the household waste.

Charging the Battery

You must charge the battery for at least 2 hours before using your phone for the first time.

Using the Charger

1. Remove the cover of the external connector, and

connect the charger to the external socket located at the bottom of the phone by pressing both sides indicated with arrows. Connect the charger to an AC outlet. Keep the cover in a safe place so as not to lose it.

Mobile light

The mobile light turns white when the battery needs to charge. When the phone is charging, the animated battery status icon ( ) in the upper right of the screen displays the current status. Standard charging time: Approx. 2 hours.

Note

• Charging time may vary depending on the state of the

battery and other conditions. (See “Battery” on page 119.)

To Disconnect the Charger

Push and hold the side buttons of the charger, then disconnect the charger from the external socket of the phone.

2. When charging is complete, the battery indicator

icon displays the full charge status and the mobile light turns off. Unplug the charger from the AC outlet, then unplug the charger connector from the phone. Put the cover back.

Note

• Do not use any non approved charger, this may

damage your phone and invalidate any warranty, please see “Battery” on page 119 for details.

Getting Started 13

To Charge Using the Cigarette Lighter Charger

The optional cigarette lighter charger supplies power for charging from the cigarette lighter socket of a car.

Battery Level Indicator

The current battery level is displayed in the upper right hand side of the main display and the external display.

Low Battery During Use

When the battery is running low, an alarm will sound and “ ” is displayed on the main display and the external display.

If you are using your phone and you hear the “low battery” alarm, attach your charger as soon as possible. The phone may not be able to continue normal operation if you continue to use it. The battery may only last approximately five minutes before the phone itself powers down during a call.

Battery Indicators Charge Level

Sufficiently charged

Partially charged

Charging recommended

Charging required

Empty

14 Getting Started

Turning Your Phone On and Off

To turn the power on, press and hold F for approximately 2 seconds.

The standby screen is displayed. To turn the power off, press and hold F for

approximately 2 seconds.

To Enter the PIN Code

If activated you are asked to enter a PIN (Personal Identification Number) code after turning on your phone.

1. Enter your PIN code.

2. Press .

Note

• If your PIN code is entered incorrectly three times in a row, the SIM card is locked. See “Enabling/ Disabling the PIN Code” on page 111.

To Copy Contacts List from the SIM Card

When you insert the SIM card into your phone for the first time and start the Contacts List application, you are asked whether you wish to copy Contacts List entries on the SIM card. Follow the on-screen instructions, or you can do it later using the Contacts List menu as follows:

→

“Contacts” “Advanced”

“Contacts List” → [Options] →

→

“Copy All Entries”

1. Select “From SIM to Handset”.

Display Indicators (Main Display)

Status indicators

Left soft key

Centre key

Right soft key

Getting Started 15

Status Indicators

1. / /#/#/#: Strength of received signal/Service out of range/GPRS enabled and within range/roaming outside network/GPRS enabled, within range and roaming

2. : Call incoming

3. : Call in progress

4. / : Current WAP or MMS communication mode [CSD/GPRS]

5. / : Data communication mode enabled/fax communication mode enabled

6. : “Diverts” (p. 102) set to “All Calls”

7. / : Secure WAP page displayed

8. / : Text message alerts [unread/mailbox full]

9. / : Multimedia message alerts [unread/ mailbox full]

10. /: E-mail alerts [unread/mailbox full]

11. : USB data cable connected

16 Getting Started

12. / : “Infrared” connection [enabled (grey)/ communicating (red)]

13. / : Bluetooth wireless setting [enabled/ communicating]

14. / : Java™ application [executed (colour)/ suspended (grey)]

15. (No display) / / / / : Current profile [Normal/Meeting/ Activity/Car/Headset/Silent]

16. : T9 text input method enabled

17.///: Current text input method [First letter upper case/Upper case/Lower case/ Numeric]

18. / / : “Ringer Volume” (p. 93) set to “Silent”/Vibration alert (p. 94) [enabled/enabled and silent]

19. : Battery level

20. : WAP alert

21. / : Schedule entry enabled [with/without a reminder alarm]

22. : Outbox contains unsent multimedia messages

23. : Daily alarm enabled

24. : Voicemail message alert

Display Indicators (External Display)

Status Indicators

1. : Strength of received signal

2. : Battery level

3. : USB data cable connected

Getting Started 17

4. / : “Infrared” connection [enabled/ communicating]

5. / :

Bluetooth

wireless connection [enabled/

communicating]

18 Getting Started

Navigating Functions

All applications are accessed from the Main menu. To open the Main menu, press the centre key ( ) during standby.

To launch applications, you will need to highlight menu items, and make selections. To select a menu item (indicated in quotation marks), move the cursor using a, b, c and d, and press to commit your selection.

In certain procedures, you will need to press one of the soft keys (indicated in square brackets), which are displayed at the bottom left and right of the screen. Press the corresponding soft key (A or C).

To return to the previous screen, press the right soft key if it displays “Back”. To close the Main menu, press the right soft key if it displays “Exit”.

Each section in this user guide starts with a list of items you will need to select in order (indicated in italics) before performing the procedures shown. Select each item to reveal the next set of items that you have to select. Open subsection items after opening those listed in the main section.

Example:

→

“Contacts” “Advanced”

“Contacts List” → [Options] →

Navigating Functions 19

Call Functions

Making a Call

1. Enter the area code and the phone number you wish

to dial and press D to dial. If you enter the wrong number, press [Clear] to

delete the number to the left of the cursor.

Emergency Calls

1. Enter 112 or 911 (international emergency number)

using the keypad and press D to dial.

Note

• Emergency calls may not be available on all mobile

phone networks when certain network services and/ or phone features are in use. Contact your network operator for more information.

• This Emergency number can normally be used to

make an emergency call in any country, with or without a SIM card inserted, if a GSM network is within range.

20 Call Functions

International Calls

1. Press and hol d Q until a “+” (international dialling

prefix) sign is displayed.

2. Enter the country code, followed by the area code

(without the leading zero) and the phone number, and press D to dial.

Speed Dialling

Up to 8 phone numbers from the Contacts List memory (Handset and SIM) can be assigned to speed dials. You can call the numbers using the digit keys (H to O).

For details on setting the Speed Dial List, see “Speed Dial List” on page 37.

1. To dial a number using the speed dial, press and

hold any of the digit keys (H to O). The phone number stored in the Speed Dial List is

dialled.

Redialling

You can redial numbers in the call log. Select from specific categories or “All Calls”. Specific category contains up to 10 numbers and the “All Calls” list contains up to 30.

1. Press D during standby.

2. Select the category from “All Calls”, “Dialled

Numbers”, “Missed Calls” or “Received Calls”. To switch logs, press c or d.

3. Select the phone number you wish to call.

4. Press D to redial the call.

Automatic Redialling

This setting allows you to automatically redial the number if the first attempt was unsuccessful because the called party was busy.

If you wish to stop redialling, press F or [End].

To Set the Auto Redial Function

→

“Settings”

1. Select “On” or “Off”.

Note

• When you receive an incoming call, the Auto Redial function is interrupted.

“Call Settings” → “Auto Redial”

• Automatic redialling is not available for fax and data calls.

Answering a Call

When an incoming call is detected, the phone rings and the mobile light flashes.

1. Press D, or [Answer] to answer the call.

Or press any key except F and [Busy] when the “Any Key Answer” function is enabled. Set the Any Key Answer function in the profile of each mode. (p. 98)

Tip

• When the Personal handsfree kit (option) is connected to the phone, you can answer calls by pressing the Answer button.

• If you have subscribed to the Calling Line Identification (CLI) service and the caller’s network sends the number, the caller’ s number is displayed on the screen. If the caller’s name and number are stored in the Contacts List, the caller’s name and phone number are displayed on the screen.

Call Functions 21

• If the number is a restricted number, the display shows “Withheld”.

• When receiving a call from the person whose picture is registered in the Contacts List, receiving display and the picture are displayed alternately.

Rejecting an Incoming Call

1. Press F or press and hold the side-up or side-down

key whilst the phone is ringing to reject a call you do not wish to answer.

Letting the Caller Know You are Unavailable

1. Press [Busy] whilst the phone is ringing to send a

busy tone to the caller of an incoming call letting them know that you cannot answer the call.

22 Call Functions

Incall Menu

Your phone has additional functions available whilst a call is in progress.

Adjusting the Earpiece Volume

During a call, you can adjust the earpiece volume (and handsfree volume, if connected).

1. During a call, press the side-up or side-down key to

display the Earpiece Volume screen.

2. Press the side-up key (or a/d) to increase the

volume of the call or press the side-down key (or b/c) to decrease the volume. Five levels (level 1 to 5) are selectable.

3. Press when the volume is set to the desired

level. The phone returns to the in-call screen

automatically if left unoperated.

Putting a Call on Hold

This function allows you to manage two calls at the same time. If you wish to make another call whilst you are talking to someone, you can put the current call on hold to call someone else.

To Make Another Call during a Call

1. During a call, press [Options].

2. Select “Hold”.

The current call is put on hold. To retrieve a call, press [Options] and select “Retrieve”.

3. Enter the phone number you wish to make another

call to, then press D.

Tip

• You can also make another call by entering the phone

number during a call instead of steps 1 and 2. The current call is automatically put on hold.

Call Waiting

This service notifies you of another incoming call whilst you have a call in progress.

1. During a call, press [Options] and select “Hold &

Answer” to answer the second call. The first call is put on hold and you can now talk to

the second caller.

2. Press [Options] and select “Swap Calls” to switch

between the two calls.

3. Press [Options] and select “Release Call” to end the

current call and return to the held call.

Note

• You need to set “Call Waiting” to “On” if you use the Call Waiting service (p. 103).

• Call Waiting service may not be available on all networks. Contact your network operator for more information.

• If you do not wish to answer the second call, press [Busy], or press [Options] and select “Busy” or “Reject”, in step 1. If “Reject” is selected, the call log of the second call is saved as a missed call.

Call Functions 23

Accessing SMS Menu During a Call

1. During a call, press [Options] and select “Text”.

The following options are available: “Create Message” to create an SMS, or “Inbox”, “Sent” or “Drafts” to access these folders. For details on SMS, see “Text (SMS)” on page 53.

Conference Call

Conference call is a call with more than 2 participants. You may include up to 5 participants in a conference call.

To Make a Conference Call

To make a conference call, you must have one active call and one held call.

1. During a call, press [Options] and select

“Multiparty” to answer the second call.

2. Select “Conference All” to join the conference call.

3. Press F to end the conference call.

24 Call Functions

Note

• Conference call service may not be available on all networks. Contact your network operator for more information.

• You have more options for the Conference call in step 2:

• To put all participants on hold, select “Conference

Hold All”.

• To put all participants except the current call on

hold, select “Private”.

• To end the call with all participants, select

“Release All”.

• To disconnect from the conference call but still

allow the other participants to continue talking together, select “Transfer”.

• To put the current call on hold and continue to

have a conference call with the remaining participants, select “Exclude”.

• To reject adding more participants to the current

party, select “Reject”, or you can send the busy tone by selecting “Busy”.

To Add New Participants to the Conference Call

1. Press [Options] and select “Dial”.

2. Enter the number you wish to include in the

conference call and press D to dial.

3. Press [Options] and select “Multiparty”.

4. Select “Conference All” to join the conference call.

If you wish to add other participants, repeat steps 1 to 4.

To End the Call with a Conference Call Participant

1. During a conference call, highlight the person that

you wish to disconnect from the conference call.

2. Press [Options] and select “Release Call”.

To Have a Private Conversation with One of the Participants

If you wish to have a private conversation with one of the participants, you may select the participant from the conference list and put the other participants on hold.

1. During a conference call, select the person that you

wish to talk to.

2. Press [Options] and select “Multiparty”.

3. Select “Private”.

4. Once you have finished the private conversation,

press [Options] and select “Multiparty”.

5. Select “Conference All” to return to the conference

call.

Muting the Microphone

1. During a call, press [Mute] to mute the microphone.

To unmute the microphone, press [Unmute].

Call Functions 25

Entering Characters

When entering characters to create Contacts List entries, text messages or multimedia messages, etc., press the corresponding keys.

In multi-tap input method, press each key until the desired character is displayed. For example, press H once for the letter “A” or twice for the letter “B”.

Table of Characters

Pressing each key scrolls characters in the following order. The order varies depending on the language selected.

English Mode

Key

G H I J K L

26 Entering Characters

Upper Case

Characters

. (full-stop) , (comma) - (hyphen) ? ! ’ (apostrophe) @ :1

ABC2 abc2 2

DEF3 def3 3

GHI4 ghi4 4

JKL5 jkl5 5

MNO6 mno6 6

Lower Case

Characters

Numeric

Key

M N O Q P

G-O P

Upper Case

Characters

PQRS7 pqrs7 7

TUV8 tuv8 8

WXYZ9 wxyz9 9

(space)+ = < > € £ $ ¥ % &0 0

Switches character case among four modes: Abc, ABC, 123 and abc.

.,?!:;-+#* @' ''( )_&€£$ %/ ˜<>§= \ | ¥

¿¡^[ ]{ }¤ЕД Же джаЗЙий м

СсЦШцштЯЬь

ù ∆Φ ΓΛΩΠΨΣΘ

Ξ (space) ↵

:QPress and hold to enter 0 - 9 numbers.

: Press and hold to shift between multi-

: Press and hold to display the language

tap and T9 mode.

options screen.

Lower Case

Characters

Numeric

Changing the Input Languages

You can change the input language on the text entry screen.

1. On the text entry screen, press [Options].

2. Select “Input Language”.

If “Input Language” is not displayed, select “Text Options” and then select “Input Language”.

3. Select the desired language.

Tip

• You can press and hold R instead of steps 1 and 2

to display the language options screen.

Changing the Input Method

T9 Text Input

T9 text input method is a shortcut to enter text easily and quickly.

1. On the text entry screen, press and hold P to enter

T9 mode.

2. Press [Options].

3. Select “Input Method”.

If “Input Method” is not displayed, select “Text Options” and then select “Input Method”.

4. Select the input mode (Abc, ABC, abc, 123).

5. Press each key once for any letter you require on

that key. To enter the word “How”, press J L O.

6. If the word shown isn’t the one you want, press a

or b until you highlight the correct one.

7. Press to select the word.

Note

• If the correct word is not shown in step 6, enter the correct word again after switching to the multi-tap input method.

Tip

• If you press Q instead of step 7, a space is inserted next to the selected word.

Symbols and Punctuations

1. On the text entry screen, press [Options].

2. Select “Add Symbol”.

If “Add Symbol” is not displayed, select “Text Options” and then select “Add Symbol”.

3. Select the desired symbol.

Entering Characters 27

My Dictionary

You can create your own word list for T9 text input.

1. On the text entry screen in T9 mode, press

[Options].

2. Select “My Dictionary”.

If “My Dictionary” is not displayed, select “Text Options” and then select “My Dictionary”.

3. Select “Add New Word” and enter a new word.

To edit a word in the list

1. On the text entry screen in T9 mode, press

[Options].

2. Select “My Dictionary”.

If “My Dictionary” is not displayed, select “Text Options” and then select “My Dictionary”.

3. Highlight the desired word.

4. Press [Options] and select “Edit”.

5. Modify the word.

Tip

• You can also carry out the following steps to register a new word in the list for T9 text input.

1. Enter a (part of) word in T9 mode you wish to

2. Press [Options].

28 Entering Characters

3. Select “My Dictionary”. If “My Dictionary” is not displayed, select “Text Options” and then select “My Dictionary”.

4. Modify the word.

Using Text Templates

You can use the sentences registered in Text Templates when entering characters.

For details on creating the text template, see “Adding Phrases to Text Templates” on page 70.

1. On the text entry screen, move the cursor to the

point you wish to insert the template.

2. Press [Options].

3. Select “Text Template”.

If “Text Template” is not displayed, select “Text Options” and then select “Text Template”.

4. Select the desired text template.

The selected text template is inserted.

Using the Menu

Accessing Applications

1. Press during standby.

The Main menu is displayed.

2. Navigate to required location.

3. Press to access function.

Shortcut Keys

You can shortcut to the specified menus by pressing

and digit keys for the menu’s corresponding number on the Main menu. See the following table for reference.

Shortcuts are listed in the headings of this manual. For example: “M 9-7”.

Example: To Access “Language” Sub Menu

Using Shortcut Keys

Press O M.

Note

• The shortcut keys work for the first three menu levels

only.

Using the Menu 29

List of Menu Functions

Menu No./

Main Menu

1 Games & More 1 Applications

2 Vodafone live! 1 Vodafone live!

3 Applications

4 Messages 1 Create Message

30 Using the Menu

2 Screensavers 3 More Games 4 Settings 5 Java™ Information

2 Games 3 Ringtones 4 Pictures 5 News 6 Sport 7 Find & Seek 8 Chat 9 Search

1 SIM Application 2 Alarms 3 Calculator 4 Voice Recorder 5 Melody Editor 6 Phone Help

2 Multimedia 3 Te xt 4 E-mail 5 Media Album 6 Vodafone Mail 7 Messenger 8 Cell Broadcasts 9 Area Info

Menu No./

Sub Menu1

Menu No./

Main Menu

5 Camera 1 Take Picture

6 My Items 1 Pictures

7 Calendar 8 Contacts 1 Contacts List

9 Settings 1 Connectivity

2 Record Video

2 Games & More 3 Sounds 4 Videos 5 Text Templates 6 Bookmarks 7 Memory Status

2 Add New Contact 3 Call Log 4 Speed Dial List 5 My Numbers 6 Call Timers 7 Data Counter 8 Call Costs 9 Service Dialling No.

2 Profiles 3 Display 4 Sound 5 Call Settings 6 Date & Time 7 Language 8 Network 9 Security 0 Master Reset

* Only available with some operators.

Menu No./

Sub Menu1

Note for the menu indications for the Postcard and Media Album services

• The menu indications for the Postcard and Media Album services vary in the United Kingdom and Ireland as follows:

Current

indications in

the user guide

“Postcard” “live! Postcard” (Not available)

“As Postcard” “As live! Postcard” (Not available)

“Media Album” “live! Studio” “Picture Album”

“To Album” “To live! Studio” “To Picture Album”

Indications in

United Kingdom

Indications in

Ireland

Using the Menu 31

Contacts List

You can store the phone numbers and E-mail addresses of your friends, family and colleagues in the Contacts List.

Depending on the size of the entry, your phone can store up to 640 entries. In a Contacts List, you can store the following items.

Items stored in the handset memory

First Name Last Name Tel Mobile Tel Private Tel Office E-mail Private E-mail Business Group Address (Street & Number, Postal Code, City, State/ Province, Country) Note

Tip

• There is no character limit for entering text into the above fields when using the internal memory.

32 Contacts List

(M 8-1)

Items stored in the SIM memory

Name: The number of characters that can be

Phone number: Up to 40 digits Using the infrared or Bluetooth wireless function, you

can send the Contacts List entry to a PC to share the same entries.

stored differs depending on the SIM card you use.

Selecting the Storage Memory

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Save New Contacts”

1. Select Contacts location from “Handset Memory”,

“SIM Memory” or “Choose before Saving”.

Tip

• “Choose before Saving” prompts you to choose the memory every time you save a new entry.

Changing the List Displayed

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Contacts Location”

1. Select from “Handset Memory”, “SIM Memory” or

“Both”.

Changing the Name Order

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Name Order”

1. Select from “First - Last name” or “Last - First

name”.

Add New Contact

You can choose either the phone or SIM card memory locations to store the new entry. For switching locations, see “Selecting the Storage Memory” on page 32.

The amount of phone numbers that you can store to the SIM card is dependent on its capacity. Contact your network operator for details.

→

“Contacts”

If you select the “Choose before Saving” option for the memory to be used, the selection is between “To Handset” and “To SIM”.

1. Select the field you wish to fill in, and enter the

relevant information.

2. Press [Save] when finished.

Tip

• To create an entry, at least one field must be filled. If you create a new entry on the SIM card, you need to enter a phone number.

“Add New Contact”

(M 8-2)

Adding a Thumbnail to Entries

→

“Contacts”

“Contacts List”

1. Highlight the desired entry.

2. Press [Options] and select “Edit/Add Details”.

3. Press [Options] and select “Picture”.

4. Select the desired picture.

5. Press [Save] when finished.

Note

• From the Contacts List entry that has a thumbnail added, you can change or delete it by selecting “Change” or “Remove” after step 3.

• If you delete a picture in Saved Pictures, the corresponding thumbnail is also deleted.

• If the picture size exceeds 120 dots [W] or 160 dots [H], specify the area you wish to display.

Contacts List 33

Copying Contacts List Entries between SIM Card and Handset

“Contacts” → “Contacts List” → [Options] → “Advanced”

1. Select “From SIM to Handset” or “From Handset to

SIM”.

Note

• When you insert the SIM card into your phone for the first time and start the Contacts List application, the confirmation screen appears automatically, asking you if you wish to copy or not. The number of Contacts List entries to be copied varies depending on the SIM capacity.

34 Contacts List

→

“Copy All Entries”

Copying a Single Entry from Handset to SIM Card

→

“Contacts”

“Contacts List”

1. Select the desired entry.

2. Highlight the desired phone number.

3. Press [Options] and select “Copy to SIM”.

Finding a Name and Number

“Contacts” → “Contacts List”

1. Enter the first few letters of the name.

Search results are displayed in alphabetical order.

Tip

• You can select the Contacts location from “Handset Memory”, “SIM Memory” or “Both” before searching.

• To view the details of the item such as address, highlight the desired item, press [Options]and select “View”.

Dialling from the Contacts List

“Contacts” → “Contacts List”

1. Highlight the desired entry and press D.

Tip

• If more than one phone number is registered for the entry, select the desired phone number after step 1 and press D. You can also dial the desired phone number by pressing the digit key corresponding to the position the entry is on the list.

• You can also dial from the details screen of the Contacts List. On the details screen, select the desired phone number and press D.

• If you select “SIM Memory” for the “Contacts Location” option in Contacts List menu (p. 32), only one phone number entry is displayed.

Editing Contacts List Entries

“Contacts” → “Contacts List” → [Options] → “Edit/ Add Details”

1. Select the field you wish to edit, and modify the

information.

2. Press [Save] when finished.

Deleting Contacts List Entries

Deleting All Contact Entries

“Contacts” “Advanced”

→

“Contacts List” → [Options] →

→

“Delete All Entries”

1. Enter your handset code.

2. Select “Handset Entries” or “SIM Entries”.

The default handset code is “0000”. For details on changing the handset code, see “To Change Handset Code” on page 112.

Deleting a Contact Entry

→

“Contacts”

“Contacts List”

1. Highlight the desired entry.

2. Press [Options] and select “Delete”.

Viewing Groups

You can set group icons when storing Contacts entries so that you can easily find and edit them.

→

“Contacts” “Advanced”

1. Select the desired group.

“ ” appears next to the selected group. Select the group again to cancel, and the checkbox becomes unchecked.

“Contacts List” → [Options] →

→

“Group” → “View Groups”

Contacts List 35

Tip

• Press [Options] and select “Current Only” to view only the selected group or “Select All” to view all groups.

Group Call

Different ringtones can be set for each group. When you purchase this phone, groups are set to off. If you do not set a group ringtone, the ringtone assigned in the Settings menu is used.

→

“Contacts” “Advanced” → “Group” → “Group Call”

1. Select the desired group.

2. Select “Switch On/Off”.

3. Select “On” or “Off”.

4. Select “Assign Ringtone”.

5. Select “Preset Sounds” or “My Sounds”.

6. Select the desired ringtone.

For details on selecting a ringtone, see “Assigning Ringtone” on page 94.

7. Select “Vibration” and select from “On”, “Off” or

“On & Link to Sound”. For details on selecting a vibration, see “Vibration”

on page 94.

36 Contacts List

“Contacts List” → [Options] →

8. Select “Light” and select “On”, “Off” or “On &

Link to Sound”. For details on selecting a light, see “Light” on

page 95.

9. Press [OK].

Assigning a Ringtone to Each Contacts List Entry

A specified ringtone or vibration setting can be associated to a pre-registered entry.

→

“Contacts”

1. Select the desired entry.

2. Press [Options] and select “Edit/Add Details”.

3. Press [Options] and select “Ringtone”.

4. Select “Switch On/Off”.

5. Select “On” or “Off”.

6. Select “Assign Ringtone”.

7. Select “Preset Sounds” or “My Sounds”.

8. Select the desired ringtone.

For details on selecting a ringtone, see “Assigning Ringtone” on page 94.

“Contacts List”

9. Select “Vibration” and select from “On”, “Off” or

“On & Link to Sound”. For details on selecting a vibration, see “Vibration”

on page 94.

10. Select “Light” and select “On”, “Off” or “On &

Link to Sound”. For details on selecting a light, see “Light” on

page 95.

11. Press [OK].

12. Press [Save].

Memory Status

This function helps you to check the memory used in the Contacts List.

→

“Contacts” “Advanced”

“Contacts List” → [Options] →

→

“Memory Status”

Speed Dial List

You can set a maximum of 9 phone numbers in the Speed Dial List (p. 88).

Setting Contacts List Entries in the Speed Dial List

→

“Contacts”

1. Select the desired entry.

“Contacts List”

2. Highlight the desired phone number.

3. Press [Options] and select “Add to Speed Dial”.

4. Select the desired list number.

Tip

• The nine digit keys correspond to list numbers.

• To view the speed dial list, see page 88.

Sending a Contacts List Entry

“Contacts” → “Contacts List”

1. Highlight the desired entry.

2. Press [Options] and select “Send Contact”.

3. Select “Via Bluetooth” or “Via Infrared”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the entry is sent.

Contacts List 37

For “Via Infrared”

The phone starts searching for an infrared-enabled device within 20 centimetres.

When detected, the infrared connection is established and the entry is sent.

Note

• When pairing, you need to enter your passcode when establishing contact with a Bluetooth wireless technology enabled device for the first time.

Tip

• You can send your own Contacts List entry. Select “My Card” in step 1. For details on storing your information in My Card, see “Registering Your Information as a Contacts List Entry”.

Receiving a Contacts List Entry

When the phone receives a Contacts List entry, a confirmation message appears.

1. Press [Yes].

The received entry is registered in the Contacts List. Press [No] to reject.

Tip

• For details on making Infrared or Bluetooth wireless settings, see “Connectivity” on page 90.

38 Contacts List

Registering Your Information as a Contacts List Entry

You can store your information in the Contacts List.

→

“Contacts”

“Contacts List” → “My Card”

1. Press [Options] and select “Edit/Add Details”.

2. Select the field you wish to fill in, and enter the

relevant information.

3. Press [Save] when finished.

Tip

• You can send your Contacts List entry via Bluetooth or Infrared. Highlight “My Card” in the Contacts List and press [Options]. Select “Send Contact” and then select “Via Bluetooth” or “Via Infrared”.

Dialling a Service Phone Number

Certain SIM cards contain service phone numbers that can be dialled. Contact your SIM card vendor for more information. On the Contacts screen, “Service Dialling No.” is displayed at the bottom of the list.

“Contacts”

1. Select “Service Dialling No.”.

2. Select the desired service phone number.

Tip

• If the SIM card contains only one service phone number, you can dial it in step 1 by pressing .

• If no service phone number is stored in the SIM card, this menu is not displayed.

Contacts List 39

Camera

Your phone has an integrated digital camera. This allows you to take and send pictures or video clips

wherever you are.

Take Picture

Put the phone into the digital camera mode to take a picture. Pictures are saved in Saved Pictures in JPEG format in the following three picture sizes.

Taking Pictures

“Camera”

The preview is displayed through the screen.

(M 5)

(M 5-1)

L: 480 × 640 dots M: 240 × 320 dots S: 120 × 160 dots

→

“Take Picture”

1. Press or the side-down key to take the picture.

The shutter sounds and the still image of the taken picture is displayed. Press [Cancel] to retake a picture.

2. Press [Save].

“Saving (file name) to My Items…” is displayed, then the picture is registered.

3. Press F to return to standby.

40 Camera

Remaining shots indicator

123: Indicates the remaining number of

Tip

• Pressing E during standby also activates digital

camera mode.

• If you wish to use an auxiliary ligtht, press R or the

side-up key before step 1. Press it again to turn the light off. appears or disappears on the upper part of the screen.

• If you wish to send a picture by multimedia message after taking the picture, press before step 2. Then select “Multimedia” or “Postcard”. (The Postcard service is not available with some service providers. Please contact your service provider for more information.) Large MMS messages may cause the size of attached pictures to be reduced.

Using the Full Screen

The preview can be displayed on the full screen without the soft key area and indicators.

“Camera” Viewfinder”

pictures that can be taken.

→

“Take Picture” → [Options] →“Full

1. Select “On” or “Off”.

Note

• When “Picture Size” is set to “S”, you cannot use the full screen.

Tip

• You can also turn on or off the full screen mode by

pressing Q.

Taking a Self-Portrait

To take a self-portrait, hold the phone with the mirror facing you whilst holding the phone at least 40 cm away. Press or the side-down key to take the picture.

Using the Zoom Function

Press c or d to change the zooming ratio. Zooming ratio indicators

Note

• When “Picture Size” is set to “S”, the zoom function has 3 magnifications (

• When “Picture Size” is set to “M”, the zoom function has 2 magnifications (

Selecting the Picture Size

“Camera” “Picture Size”

: Magnification.

1, ×2, ×4).

1, ×2).

→

“Take Picture” → [Options] →

1. Select the desired picture size.

Selecting the Picture Quality

“Camera” “Picture Quality”

→

“Take Picture” → [Options] →

1. Select “Normal” or “Fine”.

Picture quality indicators

:Fine :Normal

Selecting the Anti-flicker Mode

→

“Camera” flicker”

“Take Picture” → [Options] → “Anti-

1. Select “Mode 1: 50Hz” or “Mode 2: 60Hz”.

Note

• Vertical stripes may occur on the picture due to the light source. Change the anti-flicker mode to rectify.

• The digital camera uses a C-MOS sensor. Although this camera has been manufactured to the highest specifications, some pictures may still appear too bright or too dark.

• If the phone has been left in a hot place for a long time before taking or registering a picture, the picture quality may be poor.

Camera 41

In the Case of No Available Memory

When the number of pictures that can be taken becomes 3 or less, the remaining shots indicator in the upper left of the screen turns red. (The number of pictures that can be taken is approximate.)

When the number of pictures that can be taken becomes 0, and when you try to take a picture again, “Memory full. Please delete some data!” is displayed.

Adjusting the Brightness of the Picture According to Lighting Conditions

Press a or b to adjust the brightness of the picture. Picture brightness (exposure level) indicators

→

: (Bright → Normal Once the phone has returned to the standby screen, the brightness settings return to default.

42 Camera

Dark)

Viewing the Taken Pictures

→

“Camera” Pictures”

The list of pictures is displayed.

“Take Picture” → [Options] → “My

1. Select the file you wish to view.

The selected picture is displayed.

Tip

• Your pictures are given file names which are “pictureNNN.jpg” (NNN is a consecutive number). The file name (without an extension), date and size of your pictures are displayed in the list.

Using the Timer (Delay Timer)

→

“Camera” Timer”

“Take Picture” → [Options] → “Delay

1. Select “On” or “Off”.

“ ” or “ ” is displayed on the screen and the phone returns to digital camera mode.

Press or the side-down key to start the delay timer. 10 seconds after the timer sounds, the shutter

sounds, and the camera takes a picture.

Note

• The countdown sounds whilst the delay timer is operating.

• The flash light and the indicator flash whilst the delay timer is operating.

• If or the side-down key is pressed whilst the delay timer is operating, the picture is taken instantly.

• The zoom function with c or d, or brightness adjustment of the picture with a or b, is unavailable whilst the delay timer is operating.

• If you wish to stop taking pictures with the timer, press [Cancel] whilst the delay timer is operating.

Continuous Shoot

Four pictures are taken in succession. Auto Shoot and Manual Shoot are available.

Continuous Shoot indicators

When pictures are taken in Continuous Shoot mode, these indicators appear on the screen.

* When delay timer and Continuous Shoot

functions are simultaneously set, “ ” is displayed instead.

→

“Camera” “Continuous Shoot”

“Take Picture” → [Options]→

1. Select “Auto Shoot” or “Manual Shoot”.

Select “Off” to cancel.

2. Press or the side-down key to start Continuous

Shoot. Auto Shoot: Four pictures are taken in a row.

Manual Shoot: Pictures are taken one by one by

The taken pictures are saved automatically. To stop Continuous Shoot, press [Cancel].

Note

• When “Picture Size” is set to “L”, you cannot use the Continuous Shoot.

• When you select a frame for taking pictures, you cannot use the Continuous Shoot function.

• Delay timer cannot be used with the Manual Shoot.

pressing or the side-down key.

Camera 43

Selecting a Frame

You can select the frame from preset patterns. You can also select a frame in Saved Pictures.

→

“Camera” Frame”

“Take Picture” → [Options] → “Add

1. Select “Preset Frame” or “My Pictures”.

2. Select the desired frame.

The selected frame is confirmed on the display.

3. Press .

Note

• When “Picture Size” is set to “L”, you cannot use the Frame function.

• When you activate the Continuous Shoot, you cannot use the Frame function. Only images in PNG format can be selected as the frame

• if you select “My Pictures” in step 1. However, images larger than the picture size which you select cannot be used.

Selecting the Shutter Sound

You can select the shutter sound from 3 preset patterns.

“Camera” “Shutter Sound”

→

“Take Picture” → [Options] →

1. Select the desired shutter sound.

To play back the shutter sound, press [Play].

44 Camera

Note

• Continuous Shoot uses the specialised shutter sound that cannot be changed for the above settings.

Record Video

Put the phone into the video camera mode to record a video.

Video clips are saved in “.3gp” format in the following two modes:

Record size indicators

: Message sending mode enabled : Extended video mode enabled

Recording Video Clips

Sound can be recorded with the video clip.

“Camera”

The preview is displayed through the screen.

(M 5-2)

→

“Record Video”

1. Press or the side-down key to start recording

the video clip. The sound for recording the video clip occurs.

If you press or the side-down key again, or when the recording is completed, the sound for ending the video clip recording occurs and the display transits to step 2.

2. Select “Save”.

“Saving (file name) to My Items…” is displayed, then the video clip is registered. To preview a video clip before saving, select “Preview”. To send a video clip by multimedia message after recording the video clip, select “Save and Send”. To record a video clip again, press [Cancel].

Remaining sets indicator

123 : Indicates the remaining sets of video

clips that can be recorded.

Tip

• If you wish to use the auxiliary light, press R or the

side-up key before step 1. Press it again to turn the light off. appears or disappears on the upper part of on the screen.

Using the Zoom Function

Press c or d to change the zooming ratio. Zooming ratio indicators

: Magnification.

Selecting the Recording Size Mode

You can select the recording size mode.

→

“Camera” “Record Size”

“Record Video” → [Options] →

1. Select “Extended Video” or “For Message”.

Note

• If “For Message” is selected, the size of the video

clip that can be recorded depends on the message size set in MMS settings (p. 52).

• When the Message Size described on page 52 is set to

“100 KB”, “Record Size” is not displayed.

• “Save and Send” is not displayed after recording in

extended video mode.

Selecting Video Quality

→

“Camera” Quality”

“Record Video” → [Options] → “Video

1. Select “Normal” or “Fine”.

Video quality indicators

:Fine :Normal

Camera 45

Selecting the Anti-flicker Mode

“Camera” flicker”

→

“Record Video” → [Options] → “Anti-

1. Select “Mode 1: 50Hz” or “Mode 2: 60Hz”.

Note

• Vertical stripes may occur on the preview screen due to the light source. Change the anti-flicker mode to rectify.

In the Case of No Available Memory

When the number of video clips that can be recorded becomes 3 or less, the remaining sets indicator in the upper left of the screen turns red. (The number of sets that can be recorded is approximate.)

When the number of video clips that can be recorded becomes 0, and when you try to record a video clip again, “Memory full. Please delete some data!” is displayed.

Adjusting the Brightness of the Video Clips According to Light Conditions

Press a or b to adjust the brightness of the video clip. Picture brightness (exposure level) indicators

→

: (Bright → Normal Once the phone has returned to the standby screen, the brightness settings return to default.

46 Camera

Dark)

Viewing Recorded Video Clips

→

“Camera” Videos”

The list of video clips is displayed.

“Record Video” → [Options] → “My

1. Select the file you wish to view.

2. Press .

The selected video clip is played back. To pause playback, press . To resume playback, press again. To stop playback, press [Back]. To display the video clip in its original size, press [×1].

Tip

• Your video clips are given file names such as “videoNNN.3gp” (NNN is a consecutive number). The file name (without an extension), date and size of your video clips are displayed in the list.

• If the video clip has been recorded with sound, the volume can be adjusted by pressing a (or d/the side-up key) or b (or c/the side-down key).

• The volume varies depending on the Multimedia Volume settings (p. 97). The sound is deactivated when “Multimedia Volume” is set to “Silent”.

Using the Timer (Delay Timer)

To Record a Video Clip with the Timer

“Camera” Timer”

→

“Record Video” → [Options] → “Delay

1. Select “On” or “Off”.

“ ” is displayed on the screen and the phone returns to video camera mode.

2. Press or the side-down key to start the delay

timer. 10 seconds after the timer sounds, the camera starts

recording the video clip.

Note

• The countdown sounds whilst the delay timer is operating.

• If or the side-down key is pressed whilst the delay timer is operating, the video clip is recorded instantly.

• The zoom function with c or d, or brightness adjustment of the video with a or b, is unavailable whilst the delay timer is operating.

• If you wish to stop recording video clips with the timer, press [Cancel] whilst the delay timer is operating.

Recording Video Clips with Sound

→

“Camera” Record”

“Record Video” → [Options] → “Voice

1. Select “On” or “Off”.

Camera 47

Messages

Your phone allows you to send and receive text or multimedia and to receive WAP alerts.

Multimedia (MMS)

About Multimedia Messaging

Multimedia Messaging Service (MMS) allows you to send and receive multimedia messages with graphical images, photographs, sound, animations or video clips attached.

Note

• Some MMS functions may not always be available

depending on your network. Contact your network operator for more information.

Creating a New MMS

→

“Multimedia” → “Create Message”

(M 4)

(M 4-2)

(M 4-2-1)

1. Enter the message.

To use the text template, move the cursor to the point you wish to insert the template. Press [Options] and select “Text Options”. Select “Text Template” and then select the desired template.

2. Select the desired recipient from the Contacts List

entries.

48 Messages

If the desired entry does not exist, select “Enter Number” or “Enter E-mail Address” and enter the phone number or E-mail address.

3. Select “Send”.

After the message is sent, the message is moved to the Sent box.

Note

• The current message size displayed whilst you are creating the message is an approximation.

• If a message cannot be sent for some reason, the message stays in the Outbox and “ ” is displayed on the standby screen.

Tip

• To save the message without sending, select “Save to Drafts” instead in step 3.

• To enter the subject, select “Subject” in step 3 and enter it. Up to 40 characters as the subject (and up to 20 recipients (for To and Cc)) can be entered. However, these may be limited depending on your network. In this case, you may not be able to send MMS. Contact your network operator for more information.

• To add more recipients, select “Add Contact” in step

3. Select “To” or “Cc” and select the desired number of the recipient. Then enter the phone number or E-mail address.

To Send a Message Template MMS

Your phone provides message templates with an image and voice attachment that help you create MMS easily.

→

“Multimedia” → “Create Message”

A [Options] → “Message Template”

A confirmation screen asking whether you wish to discard the current text is displayed.

→

1. Confirm by selecting [Yes] or [No].

2. Select the desired template.

3. Enter the message.

4. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter

Number” or “Enter E-mail Address” and enter the phone number or E-mail address.

5. Select “Send”.

Note

• Selecting “Message Template” deletes messages or

images you have entered or attached. To prevent deletion, select “Message Template” first, then enter messages.

Turning the Slide Show Setting On or Off

→

“Multimedia” → “Settings” → “Slide Show”

1. Select “On” or “Off”.

If You Select “On”

• You can create messages which have up to 10 slides.

Each slide can contain one picture, one sound file and up to 1000 characters of text (up to the message total 30 KB or 100 KB limit).

• If you wish to add a slide to a single slide, press

[Options] and select “Add Slide”. If you wish to perform slide operations for multiple slides, press [Options] and select “Slide Control”. The slide control options available are: Add: To add a new slide. Remove: To remove the active slide. Previous: To navigate to the previous slide. Next: To navigate to the next slide.

• Video clip data cannot be attached as slide data to

the message.

Messages 49

If You Select “Off”

• You can attach a maximum of 20 pictures, sounds or video clips and up to 2000 characters of text (up to the message total 30 KB or 100 KB limit).

Inserting Attached Data

You can send pictures, sounds and video clips saved in the handset memory attached to multimedia messages. When attaching video clips, “Slide Show” must be set to “Off”.

→

“Multimedia” → “Create Message” →

A [Options]

1. Select from “Picture”, “Sound” or “Video”.

2. Select from “Saved Pictures”, “Saved Sounds” or

“Saved Videos”.

3. Select the desired file.

The selected picture/sound/video clip is attached. When attaching is complete, press [Back] to return to the message creation screen.

• To add more files, press [Options] and select from

“Add Picture”, “Add Sound” or “Add Video”. Then select from “Saved Pictures”, “Saved Sounds” or “Saved Videos”, and select the desired file.

• To remove the attached files, press [Options] and

select “Remove”.

50 Messages

Note

• Pictures/Sounds/Video clips protected with a copyright cannot be sent attached to a message.

• Instead of performing step 2, you can send data recorded with “Take Picture”, “Record Voice” or “Record Video” options.

Reading MMS

Messages you receive are stored in the Inbox.

Incoming Messages

The MMS indicator ( ) will appear when you are receiving an incoming message.

→

“Multimedia” → “Inbox”

1. Select the message you wish to view.

The message is displayed.

2. Scroll the screen to read the message.

3. Press when finished.

Tip

• The volume varies depending on the Multimedia Volume settings (p. 97). The sound is deactivated when “Multimedia Volume” is set to “Silent”.

Storing the Phone Number or E-mail Address of a Sender in the Contacts List

→

“Multimedia” → “Inbox”

1. Highlight the message from which you want to store

the phone number or E-mail address.

2. Press [Options] and select “Save Sender”.

For details on entering a name, see “Add New Contact” on page 33.

Retrieving MMS

→

“Multimedia” → “Inbox”

When “ ” is in the Inbox, the following can be done.

1. Highlight the alert you wish to download.

2. Press [Options] and select “Download”.

Tip

• You can press instead of step 2 to start downloading.

Confirming Arrival of Delivery Report

→

“Multimedia” → “Sent”

1. Highlight the messag e of which you wish to confirm

arrival of delivery report.

2. Press [Options] and select “Delivery Report”.

This menu is available only for sent messages that have the “Delivery Report” set to “On”. For details

on selecting “Delivery Report”, see “Setting Up MMS”.

Setting Up MMS

→

“Multimedia” → “Settings”

1. Select the item you wish to set up.

• Roam. Download (Immediate, Deferred): Controls MMS download timing when roaming

outside of your network. Immediate: Downloads MMS immediately from

Deferred: Asks if you would like to download

• Delivery Rep. Allow (On, Off): Enables or disables Delivery Report when

receiving a message which applies to the Delivery Report function.

• Anonymous Reject (On, Off): Rejects a messages from an unknown or empty address name or not.

• Auto Delete (Off, Inbox, Sent, Both): Deletes the oldest message automatically, when the Inbox, Sent or both (Inbox and Sent) is full.

the server.

from the server.

Messages 51

• Slide Show (On, Off): Enables or disables Slide Show when sending a

message.

• Message Size (30 KB, 100 KB): Sets the maximum message size that can be sent.

• Advanced

• Priority:

Prioritises created messages.

• Delivery Report:

Enables Delivery Report.

• Expiry Time:

Sets Expiry Time for a message to be stored in the Server.

• Sender Visibility:

Displays the information about the sender.

• Slide Interval:

Sets the slide display time when sending a message.

2. Change each item.

52 Messages

Sending a Picture File with Postcard

Your phone allows you to send multimedia messages to a Vodafone specific Postcard service centre that prints the picture and mail it to the recipient’s home address specified in the MMS message. (Your phone is initially provided with the address of a Vodafone specific Postcard service centre, and its address cannot be changed.)

Note

• This service is not available with some service providers. Please contact your service provider for more information.

To Create a New Postcard

→

“Multimedia” → “Postcard”

1. Select “Saved Pictures”.

2. Select a picture you wish to use for a postcard.

3. Enter your message.

4. Select the desired recipient from the Contacts List

entries and enter the following information. If the desired entry does not exist, select “Enter

Address” and enter the following information.

See the note below for details.

•Name •City

• Additional Information• State/Province

• Street & Number • Country

• Postal Code

5. Press [Options] and select “Send”.

Note

• Instead of performing step 1, you can use data taken with the “Take Picture” option.

• The items Name, Street & Number and City are necessary to complete sending Postcards.

• Information for a recipient Name (mandatory):

Name of the recipient for a postcard up to 50 characters

Additional Information (optional):

Additional information of the recipient up to 50 characters

Street & Number (mandatory):

Street and number up to 50 characters

Postal Code (optional):

Postal code up to 20 characters

City (mandatory):

City up to 50 characters

State/Province:

State, province, and region up to 50 characters

Country (optional):

Country up to 20 characters

The items displayed differ according to the service.

• Please contact your service provider for more information. When the item, “Country” is not displayed, you cannot send Postcards overseas.

• Files in Animation GIF format cannot be used for the Postcards service.

• The picture quality of Postcards varies depending on the picture size.

Text (SMS)

About Text Messaging

The Short Message Service (SMS) allows you to send text messages of up to 1024 characters to other GSM users.

To Use SMS with Your Phone

Messages longer than 160 characters may be composed. During sending, the messages are split. If the receiver has a suitable phone the messages recombines during reception, if not your message appears as a number of separate 152 characters messages.

(M 4-3)

Messages 53

You can send or receive SMS even if you are talking on the phone. You can also use Text Templates to help you compose SMS.

Creating and Sending a New SMS

→

“Text” → “Create Message”

(M 4-3-1)

1. Enter your message.

To use the text template, move the cursor to the point you wish to insert the template. Press [Options] and select “Text Template” and then select the desired template.

2. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter

Number” and enter the phone number.

3. Select “Send”.

The phone begins the sending process and the SMS is sent. After the message has been sent, the message is added to the Sent box. To save the message in the Drafts box without sending it, select “Save to Drafts”.

Note

• When you send a message of more than 160 characters, the confirmation message is displayed.

54 Messages

Tip

• To add more recipients, select “Add Contact” in step

3. Select an item number for adding the recipient’s phone number. Then enter the phone number.

Reading SMS

Incoming Messages

The SMS indicator ( ) will appear when an incoming message arrives.

1. When you receive a SMS, press during

standby.

2. Select the message you wish to view.

The sender’s phone number and a part of the message are displayed. When the sender’s phone number is stored in the Contacts List, the sender’s name is displayed instead of the phone number. Messages that are marked with “ ” denote unread messages. If the Inbox, Sent box or Drafts box is full, “ ” is displayed. Delete unnecessary messages.

3. Scroll the screen to read the message.

4. Press F when finished.

Extracting Phone Numbers from the Received Messages and Making a Call

You can make a call using the phone number embedded in the received SMS message.

→

“Text” → “Inbox”

1. Select the message from which you wish to extract

phone numbers.

2. Press [Options] and select “Extract Numbers”.

Telephone numbers embedded in the message are displayed.

3. Highlight the phone number.

4. Press [Options] and select “Make Call”.

To save this phone number in the Contacts List, select “Save Number”.

Setting Up SMS

To Set Up the Service Centre Address

→

“Text” → “Settings” → “Message Centre”

(M 4-3-5)

1. Enter the centre phone number.

If you wish to enter a country code for a message to an international number, press and hold Q until a “+” sign is displayed.

Message Lifetime

This indicates the number of days and hours for which a message you send may remain undelivered to the message recipient.

During this period, the message service centre will continually try to deliver the message to the recipient.

→

“Text” → “Settings” → “Message Lifetime”

1. Select the validity period.

Message Format

→

“Text” → “Settings” → “Message Format”

1. Select the message format.

Connection Type

→

“Text” → “Settings” → “Connection Type”

1. Select the connection type.

Messages 55

Optimisation

When set “On” (default), double-byte characters such as European characters with an accent are converted into single-byte characters and sent.

When “Off”, double-byte characters are sent as displayed.

Please note that you may be charged double for doublebyte characters sent in an SMS when Optimisation is set “Off”.

→

“Text” → “Settings” → “Optimisation”

1. Select “On” or “Off”.

E-mail

About E-mail Messaging

The E-mail service allows you to send and receive Email messages. E-mail messages of up to 2000 characters can be sent. The size of the E-mail messages to be received depends on E-mail settings.

Note

• You cannot send E-ma il messages with files attached.

56 Messages

(M 4-4)

If you forward E-mail messages with files attached, the attached files are deleted.

Creating a New E-mail Message

→

“E-mail” → “Create Message”

1. Enter the message.

2. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter E-

mail Address” and enter the E-mail address.

3. Select “Send”.

After the message is sent, the message is moved to the Sent box.

Note

• If a message cannot be sent for some reason, the message stays in the Outbox.

Tip

• You can use the text template to make it easier to complete the message, and you can add your signature at the end of the message. To use the text template, move the cursor to the point you wish to insert the template. Press [Options] and select “Text Template”. Select the desired template. To add the signature, press [Options] and select “Add Signature”. Select the desired signature.

• Select “Save to Drafts” instead in step 3 to save the message without sending.

• Select “Subject” in step 3 to enter the subject. Up to 40 characters as the subject (and up to 30 recipients (for To, Cc and Bcc)) can be entered.

• Select “Add Contact” instead in step 3 to add more recipients. Select “To”, “Cc” or “Bcc” and select or enter the desired address of the recipients.

• If you wish to set the priority, select “Priority” instead in step 3 and select “Urgent” or “Normal”.

Reading an E-mail Message

Incoming Messages

The E-mail indicator ( ) will appear when you are receiving an incoming message.

→

“E-mail” → “Inbox”

1. Select the message you wish to view.

2. Scroll the screen to read the message.

Tip

If you wish to download E-mail messages, press A

• during standby and then select “Check E-mail”.

Storing the E-mail Address of a Sender in the Contacts List

→

“Multimedia” → “Inbox”

1. Highlight the message from which you want to store

the E-mail address.

2. Press [Options] and select “Save Sender”.

For details on entering a name, see “Add New Contact” on page 33.

Setting Up E-mail

→

“E-mail” → “Settings”

(M 4-4-7)

1. Select the item you wish to set up.

• Download Size (Whole Message, First 20KB): Controls the download size of the E-mail. The “Whole Message” option is limited to a maximum of 100 KB.

•Edit Signature: Opens the text template screen to edit the signature.

• Auto Delete (Off, Inbox, Sent, Both): Deletes the oldest message automatically when the

Inbox, Sent or both (Inbox and Sent) is full.

• Reply Message (Incl. Original Mail, Excl. Original Mail):

Includes or excludes the original message when replying.

Messages 57

Cell Broadcasts

You can receive Cell Broadcast messages or general messages such as weather forecasts and traffic reports. This information is broadcasted to subscribers in certain network areas.

This function may not be available on all mobile phone networks. Contact your network operator for more information.

Enabling/Disabling Cell Broadcasts

→

“Cell Broadcasts” → “Switch On/Off”

(M 4-8)

(M 4-8-1)

1. Select “On” or “Off”.

Reading Cell Broadcast Messages

→

“Cell Broadcasts” → “Read Messages”

(M 4-8-2)

1. Select the desired subject.

2. Scroll the screen to read the message.

3. Press [Back].

Setting Languages

You can select your preferred language for the cell broadcast message display.

→

“Cell Broadcasts” → “Settings” →

A “Language”

The current language is displayed.

58 Messages

1. Press .

The language list is displayed.

2. Select the desired language.

3. Press [Save].

Subscribing to Cell Broadcasts

Select the page of the cell broadcast message that you want.

→

“Cell Broadcasts” → “Settings” → “Set Info

A Subjects”

1. Select “Add/Remove”.

2. Select the desired page.

3. Press [Save].

Tip

• If the desired page is not in the list that appears in step 2, select “Create Subject” in step 1, then enter the subject code to add a page. For details on the subject code, contact your service provider.

Vodafone live!

Your phone is already configured to access Vodafone live! and the mobile internet*.

Vodafone live! is a new mobile internet portal which is your gateway to a new world of information, games, music and services.

Because your phone uses GPRS, a system that is much faster than previous ways of getting mobile information. Also, the connection is ‘always on’ which means there is no need to wait for dialling up. You only have to pay for the data you send or receive, not how long you’re connected.

* If you have problems getting connected, please

phone Vodafone Customer Support.

Your phone contains a WAP browser used for surfing on the Mobile Internet, where you can get a lot of useful information. Normally, pages are designed for a mobile phone.

(M 2)

Your phone is already setup to Vodafone site for WAP/ MMS Settings.

Starting the WAP Browser

1. Press C during standby.

To Exit the WAP Browser

1. Press F to exit the browser.

Vodafone live! 59

Navigating a WAP Page

• a b c d:

Move the highlights around in the screen.

• : Executes the opt ion displayed in the lower centre of the screen.

• A: Launches browser option menu.

• C: Selects an action displayed in the lower right corner of the screen. Used to access “Vodafone live!” by opening the browser.

• Q (press and hold): Starts the “Go to URL”.

• G to O (press and hold): Starts the Bookmark (WAP).

• F: Exits the browser (short press). Turns off the phone. (press and hold)

60 Vodafone live!

Browser Menu

When you are browsing, you can reach browsing options by pressing [Options].

• Select: Selects the link you wish to see. (“Select” is displayed only when the link is highlighted.)

•Home: Goes to the homepage you set in the WAP Settings.

• Add bookmark: Adds the site you are currently browsing to your list of bookmarks.

• View bookmarks: Displays a list of bookmarks.

• Save items: Saves pictures, sounds or video clips in the appropriate My Items folder.

•Go to URL: Inputs the URL of the site you wish to go to.

•History: Displays a history list.

• Forward: Moves to the next URL in the history list.

• Reload page: Refreshes the contents of the WAP page.

• Advanced...:

• Show URL:

Displays the URL of the site you are currently browsing.

• Save page:

Saves the page you are currently browsing to your list of Snap Shots.

• Snapshots:

Displays a list of Snap Shots.

• Alert inbox:

Displays a list of WAP push messages. You can receive push messages via WAP Services. This means that a service provider sends WAP content to your phone, without any set up.

•Settings:

Includes “Downloads”, etc.

• Security:

Sets the security.

• Clear...:

Clears history, cache, etc.

• Restart Browser:

Restarts the browser.

Bookmarks

When you are browsing, press [Options] and select the appropriate option.

To Add a Bookmark

1. Select “Add bookmark”.

To Access Bookmarked Pages

1. Select “View bookmarks”.

2. Select the desired bookmark.

To Edit Bookmarks

1. Select “View bookmarks”.

2. Select “More…”.

3. Highlight a bookmark page you wish to edit.

4. Press [Options] and select “Details”.

5. Edit the title, then press b.

6. Edit the URL, then press b.

7. Select “Save”.

Vodafone live! 61

To Delete Bookmarks

1. Select “View bookmarks”.

2. Select “More…”.

3. Highlight a bookmark page you wish to delete.

4. Press [Options] and select “Delete”.

5. Press [Options] and select “OK”.

Setting the Hotkeys to Web Page Bookmarks

You can access Web pages quickly by pressing the shortcut keys (hotkeys). Follow the following to assign shortcuts.

1. Select “View bookmarks”.

2. Select “More…”.

3. Highlight a bookmark page you wish to edit.

4. Press [Options] and select “Hotkeys”.

The list of hotkeys is displayed.

5. Select the number to which you wish to assign

hotkeys. The list of registered bookmarks is displayed.

6. Select the desired bookmark.

62 Vodafone live!

My Items

My Items contains several types of picture, sound and video clip data. Also included in My Items are frequently used text message phrases and accessed WAP pages (addresses) which you can use. You can also transmit picture, sound and video clip data via infrared or

Bluetooth

Note

• The phone can store approximately 2100 KB of data across Pictures, Games & More, Sounds and Videos.

(M 6)

wireless technology to OBEX-enabled phones.

Using Images as Wallpaper

→

“My Items”

The list of pictures is displayed.

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to use as wallpaper.

2. Press [Options] and select “Set as Wallpaper”.

3. Specify the area you wish to display using the

navigation keys.

Pictures

Pictures that are taken by a digital camera or images that are downloaded from mobile Internet sites can be managed. You can register pictures in the following formats: JPEG, PNG, BMP, GIF, WBMP, and WPNG.

Viewing Pictures

“My Items”

(M 6-1)

→

“Pictures” → “Saved Pictures”

1. Select the file you wish to view.

The selected picture is displayed.

My Items 63

Saving to Contacts List

You can use this option only for pictures saved in the handset memory.

→

“My Items”

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to add to Contacts List.

2. Press [Options] and select “Add to Contact”.

To overwrite, select “Existing Contact” and select the data you wish to save to. If the picture size exceeds 120 dots in width or 160 dots in height, specify the area you wish to display. To save as a new entry, select “New Contact”. For details on entering a name, see “Add New Contact” on page 33.

Editing Pictures

→

“My Items”

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to edit.

2. Press [Options] and select “Edit”.

3. Select the desired option:

“Rotate”: The picture is rotated 90º

“Adjust Size”: Select the desired option. “Retouch”: Select the retouching option. “Add Frame”: Select the desired frame pattern.

64 My Items

anticlockwise. Press [Rotate] again for another 90º.

“Add Stamps”: Press [Stamps] and select the

Note

• The size of pictures that you can retouch is 52 dots

52 dots [H] minimum.

[W]

• The size of pictures that you can add stamps to is 48 dots [W]

• Images exceeding 240 [W] or 320 [H] are saved as 240 [W]

• “Adjust Size” may not be available depending on the original picture and copyright issued.

Sending a Picture File

“My Items”

desired stamp pattern. Repeat this step to add more patterns.

48 dots [H] minimum.

320 [H] regardless of the original size.

→

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to send.

2. Press [Options] and select “Send”.

3. Select “As Multimedia” or “As Postcard”.

For details on creating a message, see “Creating a New MMS” on page 48.

Note

• The Postcard service is not available with some service providers. Please contact your service provider for more information.

• Pictures protected with a copyright cannot be sent attached to a message.

Tip

• For details on transmitting My Items data, see “Sending My Items Data” on page 69.

Uploading Picture Files

You can upload your pictures to the Media Album.

Note

• This service is not available with some service providers. Please contact your service provider for more information.

→

“My Items”

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to upload.

2. Press [Options] and select “Send”.

3. Select “To Album”.

4. Press [Yes].

Note

• Pictures protected with a copyright cannot be uploaded.

Downloading Picture Files

“My Items”

The picture file download site is displayed.

→

“Pictures” → “More Pictures”

Games & More

Along with the preloaded application, downloaded applications are stored in Applications.

Note

• Applications can store up to 50 applications.

Using Applications

Various kinds of Vodafone specific applications can be used in this phone.

To use applications, download the applications via the mobile Internet.

Some applications offer the ability to connect to a network either within a game or network based application.

Note

• Applications may be both local (no connectivity) and network based (using the mobile Internet to update information/play games). The network may charge you more for using network-based applications. Please contact your service provider for more information.

(M 6-1-3)

(M 6-2)

My Items 65

Downloading Applications

Confirmation Screen

Before downloading the application you are asked to confirm what you are about to receive.

After checking the information on the confirmation screen, the application can be downloaded.

Note

• User authentication may be required before downloading the application on some information screens.

Executing Applications

→

“My Items”

Downloaded applications are sequentially displayed from the latest one.

“Games & More” → “Applications”

(M 6-2-1)

1. Select the title of the application you wish to

execute. The selected application is executed.

When using network connection type applications, connection to the network can be selected.

2. To end the application, press F and select “End”.

66 My Items

More Games

“My Items”

(M 6-2-2)

→

“Games & More” → “More Games”

1. Select the application you wish to download.

The WAP browser is started and a confirmation message will appear asking to confirm download.

2. Press to start downloading.

3. Press when finished.

Sounds

The ringtones created using the Melody Editor and the AMR data recorded by Voice Recorder are managed in Saved Sounds. The default ringtones are not contained within Saved Sounds.

(M 6-3)

:SMAF format : Original ringtone (composed in Melody Editor) : Standard MIDI format : i Melody format : WAVE format : AMR format

Tip

• SMAF (Synthetic music Mobile Application Format)

is a format of music data for mobile phones.

Playing Back Sound Files

→

“My Items”

“Sounds” → “Saved Sounds”

1. Select the file you wish to play back.

To stop playback, press .

Note

• The volume varies depending on the Multimedia

Volume settings (p. 97). The sound is deactivated when “Multimedia Volume” is set to “Silent”. To adjust the volume, press a (or d/the side-up key) or b (or c/the side-down key).

Using the Sound Files as Ringtone

→

“My Items”

“Sounds” → “Saved Sounds”

1. Highlight the file you wish to use as ringtone.

2. Press [Options] and select “Set as Ringtone”.

The selected sound is automatically used for the ringtone of the current Profiles.

Note

• Files in AMR or WAVE format cannot be used for the

ringtone.

Sending a Sound File with MMS

→

“My Items”

“Sounds” → “Saved Sounds”

1. Highlight the file you wish to send.

2. Press [Options] and select “Send”.

3. Select “As Multimedia”.

For details on creating a message, see “Creating a New MMS” on page 48. If you select a sound file created with the Melody Editor, add the following step 4.

4. Select the file format “SMAF”, “MIDI” or

“i Melody”.

Note

• Sounds protected with a copyright cannot be sent attached to a message.

• Only the first part of the data is converted if you select “i Melody” in step 4.

My Items 67

Uploading Sound Files

You can upload your sounds to the Media Album.

Note

• This service is not available with some service providers. Please contact your service provider for more information.

→

“My Items”

“Sounds” → “Saved Sounds”

1. Highlight the file you wish to upload.

2. Press [Options] and select “Send”.

3. Select “To Album”.

If you select your original ringtone in step 1, perform the following, otherwise go to step 5.

4. Select the file format “SMAF”, “MIDI” or

“i Melody”.

5. Press [Yes].

Note

Sounds protected with a copyright cannot be uploaded.

•

Downloading Sound Files

“My Items”

The sound file download site is displayed.

68 My Items

→

“Sounds” → “More Sounds”

(M 6-3-4)

Videos

Video clips that are recorded by a video camera or video clips that are downloaded from mobile Internet sites can be managed.

Playing Back Video Clip Files

“My Items”

(M 6-4)

→

“Videos” → “Saved Videos”

1. Select the file you wish to play back.

2. Press .

To resume, press again. To stop playback, press [Back]. To return to the original size, press [×1].

Note

• The volume varies depending on the Multimedia Volume settings (p. 97). The sound is deactivated when “Multimedia Volume” is set to “Silent”. To adjust the volume, press a (or d/the side-up key) or b (or c/the side-down key).

Sending a Video Clip File with MMS

“My Items”

→

“Videos” → “Saved Videos”

1. Highlight the file you wish to send.

2. Press [Options] and select “Send”.

3. Select “As Multimedia”.

For details on creating a message, see “Creating a New MMS” on page 48.

Note

• Video clips protected with a copyright cannot be sent attached to a message.

Uploading Video Clip Files

You can upload your video clips to the Media Album.

Note

• This service is not available with some service providers. Please contact your service provider for more information.

→

“My Items”

“Videos” → “Saved Videos”

1. Highlight the file you wish to upload.

2. Press [Options] and select “Send”.

3. Select “To Album”.

4. Press [Yes].

Note

• Video clips protected with a copyright cannot be uploaded.

Downloading Video Clip Files

→

“My Items”

The video clip file download site is displayed.

Sending My Items Data

Choose the appropriate menu.

“My Items” “My Items” “My Items”

“Videos” → “More Videos”

→

“Pictures” → “Saved Pictures”

→

“Sounds” → “Saved Sounds”

→

“Videos” → “Saved Videos”

(M 6-4-3)

1. Highlight the desired file.

2. Press [Options] and select “Send”.

3. Select “Via Bluetooth” or “Via Infrared”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the file is sent.

My Items 69

For “Via Infrared”

The phone starts searching for an infrared-enabled device within 20 centimetres.

When detected, the infrared connection is established and the file is sent.

Note

• Pictures/Sounds/Video clips protected with a copyright cannot be sent.

• When pairing, you need to enter your passcode when establishing contact with a Bluetooth wireless technology enabled device for the first time.

Receiving the My Items Data

When the phone receives the My Items data, a confirmation message appears.

1. Press [Yes].

The received data is registered in the corresponding My Items folder. Press [No] to reject.

Tip

• For details on Infrared or Bluetooth wireless settings, see “Connectivity” on page 90.

70 My Items

Text Templates

You can register up to 20 text templates for use in text messages and multimedia messages.

120 characters may be registered in any text template.

Adding Phrases to Text Templates

“My Items”

→

(M 6-5)

“Text Templates”

1. Select the number you wish to register.

2. Enter the text and press .

Editing Text Templates

“My Items”

→

“Text Templates”

1. Highlight the text template you wish to edit.

2. Press [Options] and select “Edit”.

3. Enter new text and press .

Viewing Text Templates

“My Items”

The list of Text Templates is displayed.

→

“Text Templates”

1. Highlight the text template you wish to view.

2. Press [Options] and select “View”.

Deleting Text Templates

“My Items”

→

“Text Templates”

1. Highlight the text template you wish to delete.

2. Press [Options] and select “Delete”.

Memory Status

This function helps you to check the memory status of My Item. Memory status covers Applications, Pictures, Sounds, and Videos.

“My Items”

→

(M 6-7)

“Memory Status”

My Items 71

Games & More

Applications

The list of Java™ applications is displayed. Downloaded applications are displayed in order

starting from the latest one.

Executing Applications

For details on executing applications, see “Executing Applications” on page 66.

Showing Application Details

“Games & More”

(M 1)

(M 1-1)

→

“Applications”

1. Highlight the desired Java™ application.

2. Press [Options] and select “Application Details”.

The detailed information is displayed.

Setting Permission

When using Java™ applications that access the network, online security for monetary transactions can be set with this option.

To Select the Function and Confirmation Method

→

“Games & More”

“Applications”

1. Highlight the desired Java™ application.

2. Press [Options] and select “Permission”.

72 Games & More

3. Select “Network Access” to set how the Java™

application accesses the network.

4. Select the desired confirmation method.

Always Connect:Allows the Java™ application access

without confirmation.

First Time: Informs you when the Java™

application accesses the network for the first time. If access is allowed, no more confirmations are made until you delete the application.

Per Session: Informs you when the Java™

application accesses the network for the first time. If access is allowed, no more confirmations are made until the application finishes operation.

Per Access: Informs you every time the Java™

application accesses the network regardless of whether or not access is allowed.

Never Connect: Prevents the Java™ application from

accessing the network and no confirmation is made.

To Reset Permissions

You can reset all permissions you made

“Games & More”

→

“Applications”

1. Highlight the desired Java™ applications.

2. Press [Options] and select “Permission”.

3. Select “Reset Permissions”.

Resume Time

You can set the time period for the screensaver application to activate.

“Games & More” Time”

(M 1-2-3)

→

“Screensavers” → “Resume

1. Enter the resume time in two digits using the digit

key.

Screensavers

You can download screensaver applications for the standby screen.

“Games & More” On/Off”

(M 1-2)

→

“Screensavers” → “Switch

1. Select “On” or “Off”.

Note

• If you select “On” and a screensaver application is

not set, a list displaying available screensavers appears, asking you to make a selection.

Set Application

“Games & More” Application”

The downloaded applications are displayed.

(M 1-2-2)

→

“Screensavers” → “Set

1. Select the desired screensaver application.

More Games

You can download applications.

“Games & More”

The application download site is displayed.

(M 1-3)

→

“More Games”

1. Select the application you wish to download.

The WAP browser is started and a confirmation message will appear asking to confirm download.

2. Press to start downloading.

3. Press when finished.

Games & More 73

Settings

Calls & Alarms

You can set the priority of incoming calls and alarms whilst an application is operating.

“Games & More”

(M 1-4)

(M 1-4-1)

→

“Settings” → “Calls & Alarms”

1. Select “Incoming Call” or “Alarm”.

2. Select methods.

• “Call Priority” or “Alarm Priority”: The application is suspended automatically, and you can receive a call, or the alarm will sound. After finishing the call or the alarm ends, the suspend icon ( ) is displayed letting know there is a suspended application.

• “Call Notice” or “Alarm Notice”: The marquee (character scrolls) is displayed on the first line of the screen whilst the application continues. If you press D, the application is suspended, and you can receive a call. After finishing the call, the suspend icon ( ) is displayed letting know there is a suspended application.

74 Games & More

Sound Volume

You can set the volume of the application such as sound effect to one of the five levels or silent. When “Multimedia Volume” (p. 97) is set to “Silent”, this setup has priority.

“Games & More”

The current volume level is displayed.

(M 1-4-2)

→

“Settings” → “Sound Volume”

1. Press a (or d) to increase the volume or press b

(or c) to decrease the volume and then press .

Backlight

“Games & More” “Switch On/Off”

(M 1-4-3)

→

“Settings” → “Backlight” →

1. Select from “Always On”, “Always Off” or

“Default Settings”.

• “Always On”: Lit whilst the application

• “Always Off”: Unlit whilst the application is

• “Default Settings”: Works with the main backlight

is operated.

operated even if a key is pressed.

setting. (p. 100)

To Set the Blinking Operation

This setting enables the backlight to be controlled by the application. If set to “Off”, the backlight cannot be turned on from the application.

→

“Games & More” “Blink”

“Settings” → “Backlight”→

1. Select “On” or “Off”.

Vibration

When the vibrator is set in the application, you can choose whether the operation is enabled or disabled.

When a SMAF file is specified in the application, you can operate the vibrator set in the SMAF file.

Note

• SMAF (Synthetic music Mobile Application Format)

“Games & More”

(M 1-4-4)

is a music data format for mobile phones.

→

“Settings” → “Vibration”

1. Select from “On”, “Off” or “On & Link to Sound”.

When you set “On & Link to Sound”, the vibration is synchronised with the sound of SMAF file in the application.

Set to Default

To Reset All Items in Settings Menu

“Games & More”

(M 1-4-5)

→

“Settings” → “Set to Default”

1. Enter your handset code.

The default handset code is “0000”. For details on changing the handset code, see “To Change Handset Code” on page 112.

Java™ Information

The information about the licenses belonging to Java™ is displayed.

(M 1-5)

Games & More 75

Applications

SIM Application

You can refer to the information on the SIM. Contact your service provider for further details.

Alarms

Setting the Alarms

The alarm function allows you to be alerted at a specified time. Note that the alarm may not function correctly if the clock has not been set.

Note

• The alarm functions even if the phone is switched off.

• The alarm will not ring when “Ringer Volume”

“Applications”

1. Select the blank setting.

2. Enter the desired time.

To Change the Type of Alarm Tone

3. Select “Set Alarm Tone”.

4. Select “Tone”.

5. Select “Preset Sounds” or “My Sounds”.

76 Applications

(M 3-2)

(p. 93) is set to “Silent”.

→

“Alarms”

(M 3)

(M 3-1)

6. Select the desired tone.

For details on selecting a tone, see “Assigning Ringtone” on page 94.

To Change the Vibration of Alarm Tone

7. Select “Vibration”.

8. Select “On”, “Off” or “On & Link to Sound”.

For details on selecting a vibration, see “Vibration” on page 94.

To Change the Duration of Alarm Tone

9. Select “Duration”.

10.Enter the desired time (02-59).

11.Press [Back].

To Set the Repeating Option

12.Select “Repeat Daily”.

13.Select “On” or “Off”.

14.Press [Save].

Editing the Alarm Setting

“Applications”

→

“Alarms”

1. Select the desired setting and edit it.

Resetting an Alarm Setting

“Applications”

→

“Alarms”

1. Select the alarm you wish to reset.

2. Select “Reset Alarm”.

Resetting All Alarm Settings

“Applications”

Deactivating or Activating an Alarm

“Applications”

→

“Alarms” → “Clear All”

→

“Alarms”

1. Highlight the alarm you wish to deactivate or

activate.

2. Press [Options] and select “Switch Off” or “Switch

On”.

Calculator

The calculator function performs the 4 arithmetic calculations using up to 12 digits.

“Applications”

The calculator is displayed on the display. Key operations for calculation are as follows.

To enter a decimal point, press R. To clear the entered number or operand, press [Clear]. To do the calculations, press . To start a new calculation, press [Clear].

(M 3-3)

→

“Calculator” → “Calculator”

Applications 77

Rate Conversion

You can also use the calculator as a currency calculator to convert from/to a home currency using a conversion rate that you enter.

To Set a Currency Conversion Rate

“Applications”

(M 3-3-2)

→

“Calculator” → “Exchange Rate”

1. Select “Foreign -> Domestic” or “Domestic ->

Foreign”.

2. Enter the currency conversion rate.

To delete all digits, press [Clear].

To Convert a Value

→

“Applications”

“Calculator” → “Calculator”

1. Enter the value to be converted.

2. Press [Options] and select “In Domestic” or “In

Foreign”. The result is displayed.

If you select “Exchange Rate” in step 2, you can set a currency conversion rate.

Note

• You cannot perform step 2 when an arithmetic

78 Applications

symbol (

+, −, ×

or ÷ ) is displayed.

Voice Recorder

This allows you to record a voice clip of up to 60 seconds, which can be used to remind you of schedule entries or be sent within a multimedia message. The recorded voice clip is registered in Saved Sounds. Voice clips are saved in “.amr” format.

Recording a Voice Clip

“Applications”

(M 3-4)

→

“Voice Recorder”

1. Press to start recording.

To stop recording before the recording time is over, press .

2. Select “Save” to save the voice clip.

To play back the recorded voice clip, select “Playback”. To record a voice clip again, press [Cancel].

Note

• To change recorded size before recording, press [Options] and select “Record Size”. Then select “Extended Voice” or “For Message”.

• When the Message Size described on page 52 is set to “100 KB”, “Record Size” is not displayed.

Sending Voice Clips

→

“Applications”

“Voice Recorder”

1. Press to start recording.

2. Press to stop recording.

3. Select “Save and Send”.

For details on creating a message, see “Creating a New MMS” on page 48.

Note

• “Save and Send” is not displayed after recording in extended voice mode.

Melody Editor

You can create an original ringtone, or you can send a melody attached to a multimedia message.

You can input up to 95 tones × 32 voices, 190 tones × 16 voices, or 380 tones × 8 voices per melody.

The original ringtone is registered in Saved Sounds.

Creating Your Original Ringtone

“Applications”

(M 3-5)

(M 3-5-1)

→

“Melody Editor” → “Create New”

1. Enter the title.

Up to 24 characters can be entered.

2. Select a tempo.

The music tempo is described below.

• “Allegro (Fast)”: 150

• “Moderato (Normal)”: 125

• “Andante (Slow)”: 107

• “Adagio (Very Slow)”: 94

3. Select from “8 Chords”, “16 Chords” or “32

Chords”.

Applications 79

4. Press the digit keys to specify the musical scale and

rest. For details on specifying the sound level and rest,

see “To Specify the Musical Scale and Rest” on page 81.

5. Press P or R to specify the types of musical

notes or rest. For details on specifying the musical notes and rest,

see also “To Specify the Types of Notes and Rests” on page 81.

6. Press d after inputting one note.

Input the next note after the cursor moves to the right.

7. Repeat steps 4 to 6 to input notes.

When entering notes, you can do the following:

• Press to play back all input notes.

• Press [Options] and select: “Play before Cursor” to play back notes up to the cursor position. “Select Part” to select another chord. “Set Tone” to set or change the tone using different instruments. (p. 82) “Set Strength” sets the strength of the tone. (p. 82)

80 Applications

8. When you finish inputting, press [Options] and

select “Save”.

9. Select “Save to My Items”.

Note

• The volume varies depending on the Multimedia Volume settings (p. 97). The sound is deactivated when “Multimedia Volume” is set to “Silent”.

• If the capacity or memory in Saved Sounds becomes insufficient, the message, “Maximum capacity : 250 Not registered.” or “Memory fu ll. Please delet e some data!” is displayed. The screen returns to step 9. Try again after deleting unnecessary data.

• Melodies consisting of too many short notes (semiquavers and triplets) cannot be played back in step 8 and the following message is displayed: “Can not play due to too many notes per sec.” The screen returns to step 5. The message “Can not save due to too many notes per sec.” may also be displayed, and the screen returns to step 5. Reduce the number of melodies, replace short notes, cancel triplets, etc. to remedy.

To Specify the Musical Scale and Rest

Using the keys shown below, specify the musical scale and rest.

Do Re Mi Fa Sol La Ti

Rest

GHIJKLM Q

When you press the key shown above once, a crotchet is specified in the middle scale (no mark).

When you press the same key repeatedly, the note will shift cycle through the available octave ranges.

LLL

When you press a or b whilst a note is selected, the note will move one semitone higher or lower.

When entering rest, crotchet rest is entered.

To Specify the Types of Notes and Rests

Press P or R repeatedly.

PP P

( ) ( ) ( ) ( ) ( )

When you make a dotted note or a triplet, press O after selecting the target note.

Note

• You cannot make a dotted semiquaver (semiquaver

rest) or a dotted semibreve (semibreve rest).

• Three continuous notes are required for a triplet.

To specify a tie, press N after selecting the target notes.

An underscore (_) is displayed next to the note, and the note is tied with the next one.

To enter the next note, press d to move the cursor to the right. Then, repeat the operation on the previous pages.

Applications 81

If the cursor is positioned next to a note, you can repeat the note immediately left of the cursor when a or b is pressed.

To Set the Tone

The phone can play notes using different instruments. You can select from 128 basic tones (8 types of: Pianos,

Chimes, Organs, Guitars, Basses, Strings 1, Strings 2, Brasses, Reeds, Flutes/Pipes, Synth Leads, Synth Pads, Synth Effects, Ethnics, Percussions, and Effects) and 61 extended tones (40 types of Drums (FM) and 21 types of Drums (WT)).

1. Press [Options] and select “Set Tone” in step 7 on

page 80.

2. Press c or d to highlight a category of the tone.

3. Press a or b to highlight a tone.

4. Press .

Now you can create an original ringtone.

Tip

• You can play back the melody in the selected tone by pressing [Options] and select “Play Current Part” in step 4, or play back the syllable names in the selected tone by selecting “Confirm Tones” instead.

82 Applications

To Set the Strength of the Tone

The strength of the tone can be set in 3 levels for each part.

When you purchase this phone, the strength of the tone is set to “Loud”.

1. Press [Options] and select “Set Strength” in step 7

on page 80.

2. Select a strength of the tone.

Now you can create an original ringtone.

Editing Original Ringtones

→

“Applications”

“Melody Editor” → “My Sounds”

(M 3-5-2)

1. Highlight an original ringtone you wish to edit.

2. Press [Options] and select “Edit Melody”.

3. Edit the title.

4. Select a tempo and number of voices.

5. Edit the data.

6. When you finish editing, press [Options] and select

“Save”.

7. Select “Save to My Items”.

8. Select “Overwrite” or “New”.

Note

• When the number of voices is modified in step 4, a

confirmation message may be displayed. When you press [Yes], a section of the melody may be deleted.

Tip

• You can delete the melody after or before the cursor

by pressing [Options] and selecting “Delete after Cursor” or “Delete before Cursor”.

Copying and Pasting Notes

You can copy and move a part of the melody to another position.

Only original ringtones or editable melodies can be copied or moved.

1. In the Score input screen, press [Options] and select

“Copy” or “Cut”.

2. Move the cursor to the first note to be copied or to

be cut.

3. Move the cursor to the last note to highlight the

area.

4. Press [Options] and select “Paste”.

5. Move the cursor to the point you wish to paste the

notes.

Phone Help

You can view the help list and use it to guide you in the phone’s functions.

“Applications”

(M 3-6)

→

“Phone Help”

1. Press a or b.

Applications 83

Calendar

Calendar allows you to easily schedule appointments, which are associated with the date and time.

These entries can also be sent via infrared or Bluetooth wireless technology to a PC to share the same schedules.

Creating a New Entry

“Calendar”

(M 7)

1. Highlight the desired day to which you want to add

an event.

2. Press [Options] and select “Add New Entry”.

3. Enter the subject.

4. Enter the location.

5. Select the desired category.

6. Enter the start date.

7. Enter the start time.

8. Select the desired duration.

9. Select the desired reminder option.

84 Calendar

Note

• The reminder functions even if the phone is switched off.

• The reminder will not sound when “Ringer Volume” (p. 93) is set to “Silent”.

• When selecting “Other” in step 9, you can enter the desired date and time.

Editing the Reminder Tone

“Calendar”

1. Select the day including schedule entries the

reminder tone of which you wish to edit.

2. Highlight the desired entry.

3. Press [Options] and select “Edit”.

Select the reminder field and select the desired option. If you select “No Reminder”, the reminder is turned off.

Select “Tone” and select “Preset Sounds” or “My Sounds”.

6. Select the desired tone.

For details on selecting a tone, see “Assigning Ringtone” on page 94.

7. Select “Vibration” and select from “On”, “Off” or

“On & Link to Sound”. For details on selecting a vibration, see “Vibration”

on page 94.

8. Select “Duration” and enter the desired time.

9. Press [OK].

10. Press [Save].

Sending a Schedule Entry

“Calendar”

1. Select the day including schedule entries you wish

to send.

2. Highlight the desired entry you wish to send.

3. Press [Options] and select “Send”.

4. Select “Via Bluetooth” or “Via Infrared”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the entry is sent.

For “Via Infrared”

The phone starts searching for an infrared-enabled device within 20 centimetres.

When detected, the infrared connection is established and the entry is sent.

Note

• When pairing, you need to enter your passcode when

establishing contact with a Bluetooth wireless technology enabled device for the first time.

Receiving a Schedule Entry

When the phone receives a schedule entry, a confirmation message appears.

1. Press [Yes].

The received entry is registered in the Calendar. Press [No] to reject.

Calendar 85

Tip

• For details on making Infrared or Bluetooth wireless settings, see “Connectivity” on page 90.

Viewing an Entry

“Calendar”

1. Select the day including schedule entries you wish

to view. The list of entries is displayed.

2. Select the desired entry.

Press d to switch entries, if available, in the selected day.

To Search By Date

1. In the monthly or daily view, press [Options].

2. Select “Go to”.

3. Select “Today” to display today or “Enter date” to

enter the desired date.

To Search By Subject

1. In the monthly or daily view, press [Options].

2. Select “Find”.

3. Enter the desired text.

86 Calendar

To Change the Week Format

1. In the monthly view, press [Options].

2. Select “Week Format”.

3. Select “Monday-Sunday” or “Sunday-Saturday”.

Deleting Entries

1. In the monthly or daily view, press [Options].

2. Select “Delete”.

3. Select the desired option.

• “This Entry” (daily view only): Deletes the selected entry.

• “All this Day”: Deletes all entries for the selected day.

• “All this Month”: Deletes all entries for the selected month.

• “Up to Last Month”: Deletes all entries before this month.

• “All Entries”: Deletes all entries in this application.

Contacts

Call Log

The phone will record the last 10 missed calls, received calls and dialled numbers.

Viewing Call Log

“Contacts”

(M 8)

(M 8-3)

→

“Call Log”

1. Select the category from “All Calls”, “Dialled

Numbers”, “Missed Calls” or “Received Calls”. The selected call log list is displayed.

To switch logs, press c or d.

2. Select the phone number you wish to view.

If you wish to dial the number, press D.

Tip

• You can also confirm call logs by pressing D during

standby mode.

Sending Messages

1. In call log list, highlight the call log you wish to

send a message to.

2. Press [Options] and select “Create Message”.

3. Select “Multimedia”, “Text” or “Postcard”.

For details on creating a message, see “Creating a New MMS” on page 48 or “Creating and Sending a New SMS” on page 54.

Note

• The Postcard service is not available with some service providers. Please contact your service provider for more information.

Deleting a Call Log

1. In call log list, highlight the call log you wish to

delete.

2. Press [Options] and select “Delete”.

Contacts 87

Speed Dial List

You can view and perform other operations for phone numbers registered in the Speed Dial List.

“Contacts”

The names and phone numbers stored in the Speed Dial List are displayed in order.

→

My Numbers

You can check your own voice, data and fax phone numbers.

“Contacts”

→

(M 8-4)

“Speed Dial List”

(M 8-5)

“My Numbers”

1. Select the phone number you wish to check from

“Voice”, “Data” or “Fax”.

Note

• “Data” or “Fax” may not be displayed depending on the SIM card.

88 Contacts

Call Timers

This function lets you check the duration of your calls.

Checking the Duration of the Last Call and All Calls

“Contacts”

(M 8-6)

→

“Call Timers”

1. Select “Received Calls” or “Dialled Numbers”.

The duration of the last call and all calls are displayed.

Data Counter

You can confirm the amount of bytes that you used in the GPRS transmission.

“Contacts”

(M 8-7)

→

“Data Counter”

1. Select from “Last Data” or “All Data”.

Resetting All Data Counter

“Contacts”

→

“Data Counter” → “Clear Counter”

Call Costs

This function lets you check the charges for your calls.

Some networks do not support Charging Advice. Please check with your service provider for availability.

Checking the Cost of the Last Call

“Contacts”

The cost of the last call is displayed.

Checking the Total Call Cost

“Contacts”

The cost of all calls is displayed.

Setting the Charge Rate

Set the charge rate to calculate the call cost and set the maximum limit for call cost.

“Contacts” Units”

(M 8-8)

→

“Call Costs” → “Last Call”

→

“Call Costs” → “All Calls”

→

“Call Costs” → “Costs Units” → “Set

1. Enter your PIN2 code.

2. Enter a cost per unit.

To enter a decimal point, press R.

3. Enter a currency unit (up to 3 characters).

Setting the Charge Limit

This function is useful if you wish to make sure you do not exceed a certain charge limit.

→

“Contacts” Limit”

“Call Costs” → “Max Cost” → “Set

1. Enter your PIN2 code.

2. Enter a value.

To enter a decimal point, press R.

Resetting All Call Costs

→

“Contacts”

“Call Costs” → “Clear Costs”

1. Enter your PIN2 code.

Checking the Residual Credit

“Contacts”

→

“Call Costs” → “Residual Credit”

Contacts 89

Settings

Connectivity

By configuring the settings in this menu, you can connect to Bluetooth wireless technology or infrared enabled phones via these connections, as well as a PC via Bluetooth wireless technology, infrared or USB connections.

Using the Bluetooth Wireless Function

To Turn On or Off

“Settings” “Switch On/Off”

(M 9)

(M 9-1)

→

“Connectivity” → “Bluetooth” →

(M 9-1-1)

1. Select “On” or “Off”.

If the infrared setting has been activated, you will be asked whether you wish to deactivate it or not. Press [Yes]. The Bluetooth wireless setting is activated, and “ ” is displayed.

Tip

• You can turn the Bluetooth wireless function on or off by pressing , then R during standby.

90 Settings

To Search for Devices to be Paired

For using the Bluetooth wireless function, you need to search for other Bluetooth wireless technology enabled devices to establ ish contact with your phone. Ke ep your phone within a distance of 10 metres before searching.

→

“Settings” “Search for Devices”

The phone starts searching for devices within 10 metres.

“Connectivity” → “Bluetooth” →

1. Select the desired device for pairing.

2. Enter the device passcode.

Note

• If the Bluetooth wireless function is off before searching, the phone turns the Bluetooth wireless function on automatically and starts searching.

• If the infrared function is active, the confirmation screen to deactivate the infrared function is displayed. Press [Yes] to deactivate.

• You can only select one device for pairing. To change the paired device, see “Handsfree Devices” on page 91.

Handsfree Devices

You can activate, rename, and delete the paired handsfree device in the list.

To Activate a Device

→

“Settings” “Handsfree Devices”

“Connectivity” → “Bluetooth” →

1. Select the device you wish to activate.

Tip

• You can save battery power by turning the Bluetooth wireless function off whilst it is not in use. Turn the Bluetooth wireless function off in “To Turn On or Off” on page 90 or in “To Turn Off Automatically” on page 92.

• During a call, you can divert voice call to the paired device. Press [Options] and select “Enable Bluetooth”. If you wish to disconnect the paired device, select “Disable Bluetooth”.

To Rename a Device

→

“Settings” “Handsfree Devices”

“Connectivity” → “Bluetooth” →

1. Highlight the device you wish to rename.

2. Press [Options] and select “Change Name”.

3. Rename the device.

To Clear a Device Name

“Settings” “Handsfree Devices”

→

“Connectivity” → “Bluetooth” →

1. Highlight the device you wish to clear.

2. Press [Options] and select “Delete”.

Paired Devices

You can rename and delete the paired device in the list.

Bluetooth Wireless Settings

With this setting you can rename your phone, prevent other GX25 phones from recognising your phone, turn the Bluetooth wireless function off automatically to save battery power, etc.

To Rename Your Phone

You can rename your phone. The name is shown in other devices when your phone is detected.

→

“Settings” “Bluetooth Settings” → “Device Name”

“Connectivity” → “Bluetooth” →

1. Enter the new device name.

Settings 91

To Show or Hide Your Phone

“Settings” “Bluetooth Settings”

→

“Connectivity” → “Bluetooth” →

→

“Visibility”

1. Select the desired visibility settings.

“Show My Phone”: Allows other devices to recognize your phone. “Hide My Phone”: Hides your phone from other devices.

To Turn Off Automatically

→

“Settings” “Bluetooth Settings”

“Connectivity” → “Bluetooth” →

→

“Bluetooth Time Out”

1. Select the desired time.

Your phone turns the function off automatically in the specified time.

92 Settings

Using the Infrared Function

“Settings”

→

“Connectivity” → “Infrared”

(M 9-1-2)

1. Select “On” or “Off”.

If the Bluetooth wireless function has been activated, you will be asked whether you wish to deactivate it or not. Press [Yes]. “ ” will appear on the screen. The infrared setting will return to off when no data is transmitted/received via infrared communication.

PC Software

By connecting your phone to a PC, you can transmit pictures, sounds, video clips, and Contacts List entries. Follow the procedure to select the connection method (Bluetooth wireless, USB or Infrared connection). For details on getting the link software, see page 114.

“Settings”

(M 9-1-3)

→

“Connectivity” → “PC Software”

1. Select the desired connection type from “Data

Cable”, “Infrared” or “Bluetooth”.

Profiles

Tone sound and vibration set can be customised for each profile according to your environment.

There are 6 profiles including one user definable profile: Normal, Meeting, Activity, Car, Headset and Silent.

Activating a Profile

“Settings”

(M 9-2)

→

“Profiles”

1. Select the desired profile.

Note

• When a profile is set, the corresponding icon described on page 16 is displayed on the standby screen.

Tip

• Press and hold R to switch Profiles settings between Normal and Silent mode during standby.

Customising Profiles

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select the setting you wish to customise and change

as desired. For details about settings, pages 93 to 98.

4. Press [Save] when finished.

Resetting Profile Settings

“Settings”

→

“Profiles”

1. Highlight the profile you wish to reset.

2. Press [Options] and select “Set to Default”.

3. Enter your handset code.

The default handset code is “0000”. For details on changing the handset code, see “To Change Handset Code” on page 112.

Ringer Volume

You can adjust the ringer volume to one of 6 levels or a step tone.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

Settings 93

3. Select “Ringer Volume”.

The current volume level is displayed.

4. Press a (or d) to increase the ringer volume or

press b (or c) to decrease the ringer volume and then press .

To select “Step Tone”, press a (or d) at level 5. To select “Silent”, press b (or c) at level 1.

Assigning Ringtone

You can select the ringtone from 28 tones including 5 patterns, 3 alerts, 10 sound effects and 10 melodies. You can also select a sound in Saved Sounds as the default ringtone excluding the AMR or WAVE format.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Assign Ringtone”.

4. Select “Preset Sounds” or “My Sounds”.

5. Select the ringtone you wish to use.

To hear the demo play, press . To stop playing, press again.

6. Press [Options] and select “Assign”.

Note

• If you delete a ringtone that uses a sound in Saved Sounds, the default ringtone is set.

94 Settings

Vibration

When the vibrator option is set on, the phone will vibrate for incoming calls regardless of the ringer volume and tone settings.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Vibration”.

4. Select from “On”, “Off” or “On & Link to Sound”.

Tip

• When the “On & Link to Sound” option is selected in step 4, the vibrator synchronises with your selected melody to pulse in time with the melody. Please note that not all melodies support the “On & Link to Sound” option. Sh ould you select such a melody, only the “On” option in step 4 will allow vibrator function.

• When you select “On” or “On & Link to Sound” in step 4, “ ” is displayed on the standby screen.

Light

When the light option is on, the mobile light turns on whilst the phone receives a call.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Light”.

4. Select from “On”, “Off” or “On & Link to Sound”.

Tip

• When the “On & Link to Sound” option is selected in step 4, the lighting synchronises with your selected melody and pulses in time with the melody. Please note that not all melodies support the “On & Link to Sound” option. Should you select such a melody, only the “On” option in step 4 will allow the light function.

Alerts

You can personalise profiles for alerts including warning tone, message alert and low battery alert.

Warning Tone

Your phone emits the warning tone when an error occurs.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Alerts”.

4. Select “Warning Tone”.

5. Select “Switch On/Off”.

6. Select “On” or “Off”.

7. Select “Volume” and select from “High”, “Middle”

or “Low”.

8. Select “Tone” and select “Preset Sounds” or “My

Sounds”.

9. Select the desired tone.

For details on selecting a tone, see “Assigning Ringtone” on page 94.

10. Select “Duration” and select the desired time.

Settings 95

Message Alert

When receiving messages, special ringtones can be set.

“Settings”

→

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Alerts”.

4. Select “Message Alert”.

5. Select from “Multimedia”, “Text” or “WAP”.

6. Select “Volume” and select the desired volume.

7. Select “Sound” and select “Preset Sounds” or “My

Sounds”.

8. Select the desired ringtone.

For details on selecting a ringtone, see “Assigning Ringtone” on page 94.

9. Select “Vibration” and select from “On”, “Off” or

“On & Link to Sound”. For details on selecting a vibration, see “Vibration”

on page 94.

10. Select “Light” and select from “On”, “Off” or “On

& Link to Sound”. For details on selecting “Light”, see “Light” on

page 95.

11. Select “Duration” and enter the desired time.

96 Settings

Low Battery Alert

Adjust the volume of the alert when the battery becomes low.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Alerts”.

4. Select “Low Battery Alert”.

5. Select from “High”, “Low” or “Silent”.

Keypad Tones

When the keypad tone is set on, you will hear a confirmation tone each time you press any keys.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Keypad Tones”.

4. Select “Switch On/Off”.

5. Select “On” or “Off”.

6. Select “Volume” and select from “High”, “Middle”

or “Low”.

7. Select “Tone” and select from “Preset Sounds”,

“My Sounds” or “Default Tone”. When selecting “Default Tone”, go to step 9.

8. Select the desired tone.

For details on selecting the tone, see “Assigning Ringtone” on page 94.

9. Select “Duration” and select the desired time.

Multimedia Volume

You can adjust volume for Video Camera, Voice Recorder, Melody Editor, My Items, browser and multimedia messages.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Multimedia Volume”.

The current volume level is displayed.

4. Press a (or d) to increase the volume or press b

(or c) to decrease the volume and then press . To select “Silent”, press b (or c) at level 1.

Power On Sound/Power Off Sound

The phone can be set to emit a sound when it is switched on or off. You can define the volume, duration and the melody to be used for this task.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Power On Sound” or “Power Off Sound”.

4. Select “Switch On/Off”.

5. Select “On” or “Off”.

6. Select “Volume” and select the desired volume.

7. Select “Sound” and select “Preset Sounds” or “My

Sounds”.

8. Select the desired sound.

For details on selecting a sound, see “Assigning Ringtone” on page 94.

9. Select “Duration” and enter the desired time.

Settings 97

Echo Reduction

This function is for reducing irritating echoes, especially when using the handsfree car kit.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Echo Reduction”.

4. Select “On” or “Off”.

Any Key Answer

You can also answer a call by pressing any key except F or [Busy]. For details, see page 21.

→

“Settings”

“Profiles”

1. Highlight the profile you wish to customise.

2. Press [Options] and select “Personalise”.

3. Select “Any Key Answer”.

4. Select “On” or “Off”.

98 Settings

Auto Answer (for handsfree car kit only)

Auto Answer function allows you to answer calls automatically by connecting the handsfree car kit for Bluetooth to your phone via Bluetooth wireless technology. You can select the desired time until your phone answers.

→

“Settings”

“Profiles”

1. Highlight “Car”.

2. Press [Options] and select “Personalise”.

3. Select “Auto Answer”.

4. Select the desired time.

Select “Off” to disable it.

Setting the Display

You can change the settings of the screen.

Setting the Main Display

To Set the Wallpaper

For the standby screen, 3 pictures are provided. Pictures taken with the digital camera or images

downloaded from a WAP site can be used for wallpapers.

To Set My Pictures

→

“Settings” “Wallpaper”

“Display” → “Main Display” →

→

“My Pictures”

(M 9-3)

(M 9-3-1)

1. Select the desired picture.

2. After displaying the picture, press .

3. Specify the area you wish to display using the

navigation keys.

Note

• Some pictures cannot be used because of their picture and data types.

• When using a file in the Animation GIF format, turn the “Standby Calendar” option off.

To Display Monthly Calendar

You can display the monthly calendar during standby. By default, a two-month calendar is displayed.

→

“Settings” “Standby Calendar”

“Display” → “Main Display” →

1. Select “One Month” or “Two Months”.

Select “Off” to turn it off.

Note

• If you select “One Month” or “Two Months” when using the file in the Animation GIF format for the wallpaper, the wallpaper setting is reset to default. When using the file in the Animation GIF format, select “Off”.

To Assign the Pictures

Pictures can be displayed when turning the power on or off, when receiving an incoming call, or when operating the alarm.

Pictures taken by a digital camera or images downloaded from a WAP site can be used.

To Set Built-in Pictures

→

“Settings” “Graphics”

“Display” → “Main Display” →

1. Select the desired situation to set the picture.

2. Select “Preset Animation” when you select “Power

On” or “Power Off” in step 1. Select “Pattern 1”, “Pattern 2” or “Pattern 3” when

you select “Incoming Call” or “Alarm” in step 1.

Settings 99

Sharp HRO00036 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Useful Functions and Services

Table of Contents

Your Phone

Optional Accessories

Getting Started

Inserting the SIM Card and the Battery

Charging the Battery

Turning Your Phone On and Off

Display Indicators (Main Display)

Display Indicators (External Display)

Navigating Functions

Call Functions

Making a Call

Speed Dialling

Redialling

Answering a Call

Incall Menu

Entering Characters

Changing the Input Languages

Changing the Input Method

Using Text Templates

Using the Menu

List of Menu Functions

Contacts List

Selecting the Storage Memory

Changing the List Displayed

Changing the Name Order

Add New Contact

Copying Contacts List Entries between SIM Card and Handset

Finding a Name and Number

Dialling from the Contacts List

Editing Contacts List Entries

Deleting Contacts List Entries

Viewing Groups

Group Call

Assigning a Ringtone to Each Contacts List Entry

Memory Status

Speed Dial List

Sending a Contacts List Entry

Receiving a Contacts List Entry

Dialling a Service Phone Number

Camera

Take Picture

Record Video

Messages

Multimedia (MMS)

Text (SMS)

E-mail

Cell Broadcasts

Vodafone live!

Starting the WAP Browser

Navigating a WAP Page

My Items

Pictures

Games & More

Sounds

Videos

Text Templates

Memory Status

Games & More

Applications

Screensavers

More Games

Settings

Java™ Information

Applications

SIM Application

Alarms

Calculator

Voice Recorder

Melody Editor

Phone Help

Calendar

Contacts

Call Log