Sharp HRO00022 Users Manual

Download

USER GUIDE

Draft

April 18, 2001

Attachment M

SHARP Model TQ-CX1

Safety Information and Usage

ⅰ

Guideline

Exposure to Radio Frequency Signals

Your wireless handheld portable telephone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-held wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies:

• ANSI C95.1 (1992)

• NCRP Report 86 (1986) *2

• ICNIRP (1996) *3

Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI Standard (C95.1). The design of your phone complies with the FCC guidelines (and those standards). z To maintain compliance with FCC RF exposure guideline, if you

wear a handset on your body use the Sharp supplied or approved holster. If you do not use a body-worn accessory, ensure the antenna is at least one inch (2.54 centimeters ) from your body when transmitting. Use of non-Sharp accessories may violate FCC RF exposure guidelines.

*1 American National Standards Institute *2 National Council on Radiation Protection and Measurements *3 International Commission on Non-Ionizing Radiation Protection

Phone Operation

ⅱ

Normal Position:

Hold the phone as you would any other telephone.

Tips on Efficient Oper ati on :

For your phone to operate most efficiently:

• Do not touch the antenna unnecessarily when the phone is in use. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed.

Batteries

Caution: All batteries can cause property damage, injury or

burns if a conductive material, such as jewelry, keys or beaded chains, touches exposed terminals. The material may complete an electrical circuit and become quite hot. To protect against such unwanted current drain, exercise care in handling any charged battery, particularly when placing it inside your pocket, purse or other container with metal objects. When the battery is detached from the phone, please use any un-conductive material cover such as small poly bag : for storing your battery when not in use.

Driving

Check the laws and regulations on the use of wireless telephone in the areas where you drive. Always obey them. Also, if using your phone while driving, please:

• Give full attention to driving - driving safely is your first responsibility.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a call if

driving conditions so require.

Pacemakers

ⅲ

The Health Industry Manufacturers Association recommends that a minimum separation of six (6") inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research.

Persons with pacemakers:

• Should ALWAYS keep the phone more than six (6") inches from

their pacemaker when the phone is turned ON.

• Should not carry the phone in a breast pocket.

• Should use the ear opposite the pacemaker to minimize the

potential for interference.

• If you have any reason to suspect that interference is taking place, turn your phone OFF immediately.

Hearing Aids

Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

Vehicles Equipped with Air Bags

An air bag inflates with great force. DO NOT place objects,

including both installed or portable wireless equipment, in the

ⅳ

area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Phone Care

Your phone is designed for excellent durability under normal use conditions. Protect your phone from water damage that could result from spills or excessive exposure to rain. Never submerge your wireless phone.

Cleaning the Phone

Cleaning of this product should only be done with a damp cloth. The use of chemical cleaners may harm the finish and integrity of the radio housing and is not recommended.

All about performance and safety

Keeping tabs on signal strength

If you’re inside a building, reception may be better near a window. The quality of each call you make or receive depends on the signal strength in your immediate area. When turned on, your phone will always give you a visual indication of the signal strength in your immediate area. The visual indicator is always in the upper left corner of your display and is referred to as the signal strength indicator: [ lines indicate maximum strength and one line indicates least strength.

]. More lines indicate more signal strength. Four

Understanding Power Save mode

If you’re trying to use your Phone in an area where the signal is too weak, the Power Save feature will be automatically activated to conserve battery power when you’ve been unable to pick up a signal for 15 minutes. If your phone is in Power Save Mode, it will

periodically recheck service availability or you can do so yourself

ⅴ

Keep the metal contacts at the battery base clean.

manually by pressing any key. A message will be displayed on the screen any time Power Save has been activated.

Understanding how your phone operates

Your phone is basically a radio transmitter and receiver. When it’s turned on, it receives and transmits radio frequency (RF) signals. When your phone is in use, the system handling your call controls the power level. This power level can range from

0.006 watts to 0.6 watts.

Maintaining your phone’s peak performance

To operate your phone properly - that is, to maintain safe and satisfactory service - you should follow these rules:

• Do not hold the phone antenna at any time.

• Do not use the phone with a damaged antenna.

Avoid exposing your phone and accessories to rain or liquid spills. If your phone gets wet, turn the power off immediately, remove the battery. If it is inoperable, you should consult with the store where you purchased it. Only authorized personnel should service your phone and its accessories. Faulty service may invalidate the warranty.

Protecting your battery

For best battery performance, you should follow these guidelines: Only use Sharp-approved battery and chargers. These chargers are designed to maximize battery life. Using other batteries or chargers will invalidate your warranty and may cause damage as well. To avoid damage, only charge the battery in temperatures that range from 32° F to 104° F (0°C to 40°C). Do not use the battery charger in direct sunlight or in high humidity areas (such as a bathroom).

Never dispose of the battery by incineration (fire ).

Do not attempt to disassemble or short-circuit the battery, as

ⅵ

injuries or burns may result. You may need to recharge the battery if it has not been used for a long period of time. Replace the battery when it no longer provides acceptable performance. Do not allow metal objects or liquids to contact or short-circuit the battery terminals, as injuries or burns may result. To avoid damage, store the battery in temperatures range from -4° F to 140° F (-20°C to 60°C), and avoid leaving the battery unused for very long periods. Follow these storage rules:

• Less than one month: – 4°F to 140°F (-20°C to 60°C)

• More than one month: – 4°F to 113°F (-20°C to 45°C)

Battery disposal and recycling

Please follow these guidelines when disposing of or recycling the battery: Do not dispose of the battery by incineration (fire); the cell may explode. Check the regulations in your area for special disposal instructions. Do not open or puncture the battery; the released electrolyte is corrosive and may cause damage to the eyes and skin, and can be toxic if swallowed. Charge the battery in accordance with the instructions specified in this user guide. See “Charging the battery” on page 16. Contains Lithium-Ion Battery must be disposed of properly. Contact local agencies for information on recycling and disposal plans in your area.

Following safety guidelines

ⅶ

To operate your phone safely and efficiently, you should always follow any special guidelines in a given area and turn your phone off in areas where use is forbidden or when it may cause interference or danger.

Turn off your phone before flying

You should turn off your phone before boarding any aircraft. To prevent possible interference with aircraft systems, U.S. Federal Aviation Administration (FAA) regulations require you to have permission from a crew member to use your phone while the plane is on the ground. To prevent any risk of interference, FCC regulations prohibit using your phone while the plane is in the air.

Restricting children’s access to your phone

Your phone should not be played with by children. They could hurt themselves and others, damage the phone or make calls that increase your bill.

Using your phone near other electronic devices

Most modern electronic equipment is shielded from radio frequency (RF) signals. However, RF signals from PCS telephones may affect inadequately shielded electronic equipment. RF signals may affect improperly installed or inadequately shielded electronic operating and entertainment systems in motor vehicles. Check with the manufacturer or its representative to determine if these systems are adequately shielded from external RF signals. You should also check with the manufacturer regarding any equipment that has been added to your vehicle. Consult the manufacturer of any personal medical devices (such as pacemakers and hearing aids) to determine if they are

adequately shielded from external RF signals. Turn off the phone

ⅷ

in healthcare facilities and request permission before using the phone near medical equipment.

Cautions

Any changes or modifications to your phone not expressly approved in this document could void your warranty for this equipment and void your authority to operate this equipment. Only use approved batteries, antennas and chargers. The use of any unauthorized accessories may be dangerous and will invalidate the phone warranty if said accessories cause damage or a defect to the phone. Although your phone is quite sturdy, it is a complex piece of hardware and can be broken. Use common-sense guidelines to avoid dropping, hitting, bending or sitting on it.

Specifications Subject to change

The information contained in this manual is believed to be correct at the time of printing. However, Sharp reserves the right to change or modify any of the specifications without notice or obligation to update existing units.

Turn off your phone in dangerous areas

To avoid interfering with blasting operations, you should turn off your phone when in a blasting area or in other areas with signs indicating that two-way radios should be turned off. Construction crews use remote-controlled RF devices to set off explosives. Turn off your phone when you are in any area with a potentially explosive atmosphere. It is rare, but your phone or its accessories could generate sparks. Sparks could cause an explosion or a fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include fueling areas such as gas stations; below deck on boats; fuel or chemicals transfer or storage facilities; areas where

the air contains chemical or particles such as grain, dust or metal

ⅸ

powders; and any other area where you would normally be advised to turn off your vehicle engine. Do not transport or store flammable gas, liquid or explosives in the compartment of any vehicle that contains your phone or accessories.

FCC notice

The phone may cause TV or radio interference if used in close proximity to receiving equipment. The FCC can require you to stop using the telephone if such interference cannot be eliminated.

Liquefied petroleum Gas

Lastly, vehicles using liquefied petroleum gas (such as propane or butane) must comply with the National Fire Protection Standard (NFPA-58). For a copy of this standard, contact the National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269, Attn.: Publication Sales Division.

FCC Compliance

“This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.”

Information To User

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation; if this equipment does cause harmful

ⅹ

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1 Reorient / Relocate the receiving antenna. 2 Increase the separation between the equipment and receiver. 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4 Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment

Table of Contents

Safety Information and Usage Guideline

Getting started ...................... ..................................... 1

Parts name & Main Functions ........................ ............................1

Turning your phone on and off .........................................10

Roaming with your tri-mode telephone ............................11

Roaming settings .............................. .................................11

Displaying your phone number .........................................12

Display ..............................................................................13

Battery ...............................................................................15

Phone’s mode .......................................................... 17

Standby mode ....................................................................17

Talk mode .........................................................................17

Power save mode ..............................................................17

Voice call ..................................................................18

Making a voice call ...........................................................18

Emergency call (911) ........................................................19

One-touch dialing (Speed dialing) ....................................19

Dialing in Lock mode .......................................................19

Dialing special numbers in Lock mode .............................19

Dialing emergency numbers in Lock mode ......................20

Redialing a call ..................................................................20

Answering a call ................................................................21

Ending a call ......................................................................22

Key beep volume ..............................................................23

Adjusting ringer volume ...................................................23

Muting the microphone during a call ................................23

Roaming ............................................................................24

Setting the roaming feature ...............................................24

Voice calling experience ................................................. ..26

Caller ID ............................................................................27

Call Waiting .................................. ....................................28

Three-way Calling (Conference Call) ...............................29

Xⅱ

Call Forwarding ................................................................30

Missed Calls ......................................................................31

Dropped calls (Fade calls) .................................................31

Failed calls ........................................................................32

Prepend dialing .................................................................33

Four-digit dialing ..............................................................35

Pause dialing .....................................................................36

Data/Fax transmission ............................................. 39

Sending Fax/Data ..............................................................39

Transmission specifications .................................... ..........39

Menus ........................................................................ 40

Recalling menus ................................................................40

1. Phone Book menu ......................................... ................41

2. Calls menu .....................................................................42

3. Sounds menu .................................................................42

4. Display menu ................................................................52

5. Security menu ...............................................................61

6. Setup/Tool menu ...........................................................66

7. System menu ......................................................... ........75

Phone Book Dialing ................................................. 76

Storing a phone number and name ....................................76

Entering characters .................................................... ........78

Overwriting an existing location .......................................80

Searching for phone numbers ...........................................82

Adding a Name Ringer .....................................................84

Modifying Your phone book entries .................................85

Erasing a single phone book entry ....................................85

Erasing all of the phone book entries ................................86

Setting the Speed Dial .......................................................86

Storing your phone book entries as a secret memory .......86

Reviewing your call logs ...................................................87

Calling by using call logs ..................................................87

Reviewing the outgoing call logs, missed call logs, or

incoming call logs .............................................................88

Storing the phone number by using the call logs ..............89

Xⅲ

Erasing a single call log (outgoing, incoming or missed

call) ...................................................................................89

Reviewing you call charges ..............................................90

Voicemail ...................................................................91

Setting up your voicemail feature .....................................91

Reviewing voicemail messages ........................................ 91

Accessing by the One-Touch Access feature ....................91

Messaging .................................................................92

Notification .......................................................................92

In Standby mode ...............................................................92

In Talk mode .....................................................................92

Reviewing a text message or Web message in Standby

mode ..................................................................................93

Message menu ...................................................................94

Erasing a single message ..................................................95

Erasing all messages .........................................................95

Message ringing ................................................................96

Message memory capacity ................................................96

Messages and Lock mode .................................................96

Internet Access .........................................................97

Setting the Charging Reminder of your browser ..............97

Starting the Web browser ..................................................98

Advanced menus ............................... ................................99

Exiting the Web browser ..................................................99

Navigating the Web page ................................................100

Entering characters .........................................................102

Link ................................................................................. 103

Bookmarks ...................................................................... 104

Your Phone’s Main menu .............................. ... ......105

Accessories .............................................................108

Options ................................ ................................................. 108

Phone and battery specifications ...................................109

ⅹⅳ

THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO

WAVES .........................................................................109

Patent Information ................................................111

Index ......................................................................112

Getting started

Package Contents

• Travel charger

• Lithium-Ion battery

• User Guide

• Quick Reference

• Holster

Parts name & Main Functions

Getting started (continued)

1. Active-flip: By closing

this Active-flip, you can end a call. And the backlight will be automatically turned off.

Color LCD display:

This screen display is used to check the status when the phone is turned on. The display has four areas to display the status. (P.13 “Display”).

•

Top line: The status of the battery, signal strength, etc. are displayed.

•

2 nd line: In-use information (call time, name and number of other party (if available).

•

3 rd line: The currently set month, date, day and time are displayed.

•

Bottom line: The name of the functions to be performed by pressing the right and left soft keys and Center key. Th e name of functions displayed varies depending on the status you select.

Press this key briefly to execute the function displayed on the right corner of the bottom line on the display. [Browser] is displayed in Standby mode.

Microphone:

Use this microphone to speak to the other party during a call.

•

Press the right soft key [Mute] during a call to mute the sound from the microphone. Press the right soft key [Unmute] again to cancel the mute setting.

Right soft key:

Navigation Keys (Arrow keys):

•

Press these keys to scroll menu items, adjust sound volume, etc.

Note This user guide uses the following notations for the arrow keys.

•

Left arrow key: Press this key in Standby mode and Talk mode to view Call logs (Outgoing, Incoming, or Missed call logs).

•

Right arrow key: Press this key in Standby mode or Talk mode to display the phone book menu.

•

Up and Down arrow keys: Press these keys to set the ringer volume. Press Down key to mute the ringer during an incoming call. Press and hold Up and Down arrow keys to scroll menus quickly, if necessary.

Center Key (M key):

•

Press this key to display the menu and execute the function displayed in the center of the bottom line on the display. [M MENU] is displayed in the center of the bottom line in Standby and Talk mode.

•

Press Navigation key to scroll through menus and press this key to decide the desired menu item.

END/ Power Key:

•

Press this key to turn the power on and press and hold it to turn it off.

•

Press this key to disconnect a call or to return to Standby mode, while any menu screen is displayed.

CLR Key:

•

Press this key to backspace and delete a single space or a character. Press and hold this key to delete all characters entered.

•

Press this key to return to a previous screen.

•

Press and hold this key to return to Standby mode while any menu screen is displayed.

# / Space Key:

•

Press this key to enter either a space or #.

10.

Accessories Connector:

This connector is used to connect the charging device (Travel charger) or Data cable ( sold separately ).

11.

/ Shift Key:

•

Press this key to enter .

•

Press this key to change the letter case.

12.

Send Key:

•

Press this key to answer a call.

•

Press this key after entering telephone numbers to make a connection.

•

Press this key to make a ThreeWay call or answer a Call Waiting call during a call in progress.

•

Press this key twice in Standby mode to redial the last outgoing number.

13.

Silent mode Key:

•

Press and hold this key in Standby to enable the silent mode.

•

This mode mutes all sounds, such as ringer sound, alert, etc.

•

Press this key to mute the ringer during an incoming call.

14.

Left soft key / Message key:

•

Press the left soft key briefly to execute the function displayed in the left of the bottom line on the display.

•

The Message key is effective when “Message” is displayed in the left of the bottom line.

•

Press and hold the Message key to connect Voicemail Center.

15.

When you use headset, please adjust sound level otherwise you may cause ear damage.

Headset Connector:

connecting the commercial headset to this connector, you can talk hands-free. Keep the connector covered with the rubber plug when not using the headset.

16.

LED Indicator:

This indicator flashes to indicate an incoming call or a message, when you have closed the Active-flip with the ringer tone set to off,

•

The indicator flashes for a few seconds when you turn on the phone.

•

The indicator flashes red during charging, and goes off when the charging is complete.

Turning ON

Turning your phone on and off

1. Open the phone and press .

The LED indicator will flash, the phone will beep and the start-up screen will be displayed.

The phone will begin searching for a network signal. When a signal is found, the icon will be displayed and the

phone will enter Standby mode. Check the following elements are displayed on the Standby

screen:

•

Antenna and signal strength icon:

•

Battery icon:

•

Date and time

•

Banner: Welcome (default)

Now you are ready to make and receive a call.

Note

• The date and time are not set at the time of purchase. See page 73 for setting them.

• While the phone is searching for the network signal, the message “Searching for Service...” is displayed.

Turning OFF

1. Press and hold for 2 seconds or more.

The power-off screen will be displayed and the power-off sound will be heard.

Note

The phone will not be turned off unless you press and hold . This feature prevents your phone from being turned off accidentally

Roaming with your tri-mode telephone

Your Phone is Tri-mode, which means you can use it to make and receive calls in many places.

•

In any city where your home network provides service.

•

On other CDMA networks and conventional analog cellular networks where your home network has implemented roaming agreements.

When you use your phone outside your home network, it’s called roaming. If you’re roaming in areas where your home network has agreements in place with digital CDMA or conventional analog cellular providers, you will pay the roaming rate plus longdistance charges, where they apply.

Note

In areas where your home network does not have roaming agreements in place, you will still be able to make (but not receive) calls using a credit card. This is called manual roaming. Consult your home network operators for more information.

Roaming settings

For more roaming settings, see the corresponding pages sho wn below.

Phone’s mode (P.17)

Call guard (P.25)

Voice calling experience (P.26)

Displaying your phone number

There are two ways to display your phone number in Standby mode:

Using the menu

Press to display the Main menu.

Press to select Phone Book.

Press to select My Phone #.

Press to return to the Standby screen.

Using the right arrow key

Press to display the phone book menu.

Press to select My Phone #.

Press to return to the Standby screen.

Display

This screen display is used to check the status of your phone when the phone is turned on.

• Top line: The status of the battery, signal strength, etc. are

displayed. Details are given below.

• Bottom line: The name of the functions to be performed by

pressing the right and left soft keys and center key. The name of functions displayed varies depending on the status you select.

Signal strength: Indicating the signal strength when your phone is turned on. The more lines the greater the signal strength. The strength changes depending on the location where you are.

Service indicator: Indicating that a call is in progress. When the signal is not found or lost, the indicator # will be displayed instead.

No service indicator: Indicating that your phone is outside the service area. Meaning that you can not make or receive a call. Move to the area where your phone indicates more lines for the signal strength.

Silent mode

Battery

Your phone comes equipped with a rechargeable lithium Ion (Li-Ion) battery. This battery has already been partially charged at the factory so that you can use your phone immediately. Note : When you use phone first time after install battery, please check battery Level. Otherwise your call may drop quickly. Depend on how much battery capacity left.

Installing the battery

1. Remove Cover

Push the release button then slide the battery cover and remove at the following instruction.

2. Insert battery

Insert the battery that the metal contact side down.

3. Replace cover

Slide into the battery cover until the battery cover is locked.

Removing the battery

1. Turn the phone off.

Push the release button then slide the battery cover and remove the cover.

4. Pull out the battery from the phone.

Phone’s mode

Standby mode

When your phone is turned on, it will start searching the home network signal. If your phone is inside the home network area, it will enter Standby mode immediately. Press the digit keys to start dialing.

Talk mode

Your phone enters Talk mode at the time the telephone circuit is established. While the phone is in Talk mode, you can access the in-use function (P. 40 “In-Use menu”) by pressing mode.

Power save mode

When your phone is located outside the home network area, it will stop searching the home network signal, and enter power save mode to save power (display: Power saving mode! Press any key to exit.). After 15 minutes, your phone will automatically begin searching the signal again.

Voice call

Making a voice call

Open the phone and press and hold .

The sound is heard and the wake-up screen is displayed.

Then, (antenna) and the signal strength level ( ) will be displayed to indicate you are in a service area to make a phone call.

Enter the phone number by pressing the digit keys.

Up to 32 digits can be entered. Press to dial.

Note (Advanced ways of calling)

There are other ways to make a phone call.

1) Using the phone book (P.82)

2) Using the call logs (P.87)

3) Using the one-touch dialing (speed dialing) (P.19)

4) Using the phone number embedded in the received message

Tip

• When you have made a mistake, press to delete the last digit.

• Holding down will delete the entire number.

• If you dial the last four digits of a phone number stored in the phone

book and press , the matched entry will be recalled and be dialed up. (P.35)

• If the phone number you dialed is not stored in the phone book, the number will be kept displayed for 10 seconds on the display. Within the time, you can store the number by pressing [Store].

Emergency call (911)

1. Dial

Press to dial

Note

• To dial the emergency number in Lock mode, see below.

• To

return to Standby mode, turn the phone off and on again.

Tip

• Emergency number (911) can be dialed even if your phone is locked (P.61 “Lock mode”) or your account is restricted.

• Your phone supports 911, #911 and *911 as an emergency number.

•“9 + ” is a shortcut for making an emergency call.

One-touch dialing

1. Press and hold any of the digit keys (0 - 8).

Note

Details of setting one-touch dial are given on page 41.

Dialing in Lock mode

When making a call in Lock mode, you must enter the lock code (four-digit) first and then start dialing.

Dialing special numbers in Lock mode

1. Enter the special number.

Press to dial.

Note

Details of storing special numbers are given on page 63.

Dialing emergency numbers in Lock mode

1. Enter the emergency number.

Press to dial.

Note

Details of unlocking the phone are given on page 62.

Redialing a call

You can dial up using the outgoing call logs without entering the phone number.

1. Press in Standby mode.

The last outgoing call log will be displayed. Press again to dial.

You can also dial using the incoming, outgoing or missed call logs. Details are given later. (P.87 “Calling by using call logs”).

Answering a call

*2 This key operates as Any key function when headset is connected.

When you receive a call... Check that your phone is turned on and it is inside the service area. When your phone receives a call, it will ring, or vibrate depending

on your ringer setting. And the LED indicator flashes green, then the backlight lights up

when you open the flip. There are two ways to answer a call:

Open the phone.

Press when the phone is open, or press any key *1 (except the navigation keys and ).

•

When Any key Answer option is enabled. (P.22)

*1 ( ~ , , , , , , ,

)

Note

During a call, the current talk time will be displayed.

Tip

• You can adjust the ringer volume in Standby mode using and

. (P.43)

• You can mute the ringer sound by pressing the Silent mode key. (P.6)

• You can adjust the earpiece volume during a call using and

. (P.44)

• You can know from whom you receive a call by assigning a unique wallpaper to the phone book data.

• To reject the incoming call, press

• When the hands-free headset or hands-free car kit is connected, you can

automatically answer the call. (Auto Answer function: P.66)

• When the earphone microphone is connected, you can automatically answer the call.

briefly.

Setting the Any key answer option

1. Press [MENU] to display the Main menu.

Press to select Setup/Tool.

Press to select Calling.

Press to select Any Key Answer.

Press to select ON.

The setting will be saved and the display will return to the Calling menu screen.

Ending a call

1. Close the phone.

or Press .

The approximate duration of the last call will be displayed.

Note

• The name and number of the called party will be displayed (10 seconds) if you have stored it in the phone book. (P.76)

• You can adjust the voice volume if the headset is connected to the phone. (5 steps/default: 4)

• If the number you dialed is not stored in your phone book, your phone prompts you to save the number. Press if needed. If you do nothing, the phone will automatically return to Standby mode after approximately 10 seconds.

When the other party ends the call

The Talk time, phone number and name of the called party (if found in the phone book data) will be kept displayed for approximately 10 seconds and the display will return to Standby mode.

Key beep volume

This feature allows you to adjust the volume of beep tone (key tone) you hear when you press a key.

Press [MENU] to display the Main menu.

Press to select Sounds.

Press to select Volume.

Press to select Key Beep.

Press Silent, level 1, level 2, level 3, and level 4.

When selecting is complete, press [OK] to save the setting.

to change and play the options:

Adjusting ringer volume

In Standby mode you can quickly adjust the volume of the ringer.

Press and .

You can also change the settings for your phone’s ringer volume in the Main menu (P.43).

Muting the microphone during a call

You can mute the microphone during a call.

Press [Mute].

The display will change to [Unmute]. Your voice will be muted while the voice of the other part y

reaches you. Ending the call will reset the mute setting to off.

To unmute the microphone during a call, press [Unmute].

Roaming

Check your phone’s display showing the network status when you turn it on.

Display Status

and Home network

Other CDMA network

and Analog cellular network

Setting the roaming feature

Press to display the Main menu.

Press to select System

Press to select Set Service

Press to select Automatic or to select No Roaming.

The setting will be saved and the display will return to the System menu screen.

Automatic:

Your phone will search for your home network service first. When your home network service is not available, it will search

for an alternate system automatically.

No Roaming:

This setting allows you to select only your home network to prevent roaming.

When the desired service mode is displayed, press [OK] to save the setting.

•

Press to exit without saving the setting.

Roaming call guard

This feature allows you to display a confirmation message asking if you are really ready to use the roaming service or not.

If you set this roaming call guard to on, you can avoid being changed for the roaming service.

Press [MENU] to display the Main menu.

Press to select System.

Press to select Call Guard.

Select to select ON or to select OFF. When you are receiving the roaming service, check the

roaming status on the display. The indicator will be displayed.

Note

Always dial 11 digits (1+ area code + number) when calling from outside your home network service area.

Voice calling experience

When you use your phone on other CDMA networks, your calling experience and call quality will be similar to what you experience when making calls from within your home network.

Although certain voice calling features may not be available, your phone calls are still private and secure.

When you use your phone on analog cellular networks, your experience will be different. Cellular roaming will be similar to the quality provided by conventional analog cellular carriers today. Although you will still have the convenience of being able to make and receive voice calls, here are some differences you can expect:

• You are more likely to experience static, cross-talk, fade-out and dropped calls.

• Some voice calling features (such as Caller ID) that are standard within your home network may not be available.

• Web service and Fax calls cannot be connected.

• Security and privacy risks (eavesdropping and phone number

cloning) are the same as those of the conventional analog cellular services today.

• Battery life will be shorter when you use your phone for cellular roaming than when you use it on a CDMA network.

If you’re on a call and leave your home network service area, your call will be dropped. When reentering your home network service area while on a roaming call, end the call, and then turn your phone off and on again to acquire your home network Service.

Caller ID

< under construction >

To prevent your phone number from being displayed for a particular outgoing call.

< under construction >

When you receive a call from a number you have stored in the phone book, your phone can display the caller’s number and name, when they match.

Your number and name can also be displayed on the other caller’s phone as well.

To activate Block Own Number permanently:

To temporarily unblock the number:

Press .

Enter the phone number and then press .

Call Waiting

< under construction >

Your phone supports Call Waiting service. Using this feature, you can receive a second call while holding the current call.

When you receive a second call, the incoming call alert is heard and an alert message will be displayed.

Accepting or rejecting a second call

To accept the call, press .

The current call will be placed on hold, while the second call will be answered.

To reject the call, press [CLR].

•

Press again to switch between the current and held

call.

Note

The call log of a second call will be saved as a missed call log (P.87) if you do not answer the call.

Temporarily disabling the Call Waiting feature

< under construction >

Permanently turning off Call Waiting feature

Three-way Calling (Conference Call)

< under study > Carrier dependent

Using Three-way Calling feature, you can make a conference with two other parties.

Note

You must subscribe to the Three-way Calling service to use this feature.

Beginning the Three-way Calling

During a call press .

The current call will be placed on hold.

Enter another phone number and press . You will be connected to the third party.

Press again. Three-way calling will be started.

Ending Three-way calling

Press during Three-way calling.

When one of the other parties ends the call, you will be connected with the remaining party (Two-way calling).

Note

• Your phone will record two outgoing call logs.

• You will be charged for two calls.

Call Forwarding

< under study > Carrier dependent

Using the Call Forwarding feature, you can forward an incoming call to another phone.

When this feature is used, you can still make a call from your phone.

Note

You must subscribe to

Call Forwarding service to use this feature.

the

Setting the call forwarding number

Press [x ][x ][ x].

Enter the 11-digit phone number (1+ area code + phone number).

Press . A confirmation sound will be heard to indicate the setting

is enabled.

Disabling Call Forwarding feature

Press [x ][x ][ x] [x ] .

A confirmation sound will be heard to indicate the setting is enabled.

Missed Calls

Your phone can record calls you were not able to answer and display a list of missed calls.

When the other party has ended a call before you can answer the incoming call, your phone will put an alert message on the display to indicate that you have missed a call.

Displaying a list of missed calls

Press and [Missed].

Missed call logs list will be displayed.

Select a missed call log and press [OK] to display the content.

Press to dial or press to return to Standby mode.

Note

• Up to 20 last calls can be stored in the phone memory. If more than 20 missed calls are received, the earliest call log will be automatically replaced with the new one.

• Unanswered calls in the Call Waiting service can be recorded in the list of missed calls.

• To display a list of your call logs, see “Reviewing your call logs

page 87.

” on

Dropped calls (Fade calls)

When your phone leaves your network service area or a signal fade occurs, an alert message (“Signal Faded” ?) appears on the display.

When a dropped call occurs, it will be automatically ended and the phone will return to Standby mode.

Press to clea r the alert message.

Note

< Carrier dependent >

If the dropped call is your outgoing call, the call log will be recorded in the outgoing call log list, so that you can redial the number by pressing

twice.

Failed calls

When your phone is outside the calling range or your service network is temporarily busy, it displays the following alert messages on the display: “Call Failed Out of Range” or “Call Failed Network Busy”.

Keep your phone located inside the calling range or make a call later.

•

Press to cancel the call, or press to clear the alert message.

Dialing your home network directory assistance

Dial [x] [x] [x] to get the following directory information:

•

Residential listings

•

Business listings

•

Government listings

•

Local or long-distance call assistance

•

Leisure listings (Movie, hotel, restaurant and shopping)

•

Major local event information, etc.

Dialing your home network operator services

Dial [x] [x] [x] to get the following operator services.

•

Making collect calls

•

Making calls billed to a local telephone calling card or a third party.

Prepend dialing

The feature allows you to add additional number(s) (e.g. area code, pauses) before the phone number stored in your phone book.

Press [MENU] to display the Main menu.

Press to select Phone Book.

Search for the desired number to be prepended.

Details of searching method are given on page 82.

Press .

Press

Press to select Prepend.

Enter the prepend digits (area code or feature activation code) by pressing the digit keys. For feature calls, press before dialing the feature code.

Press to call the prepended number.

To prepend a phone number from your call logs:

Press [MENU] to display the Main menu.

Press to select Calls.

Press to select Call Logs (outgoing call logs).

•

Press [Missed] to display the missed call logs.

•

Press [Income] to display the incoming call logs.

[Func] to display the Function menu.

4. Select the desired number to be prepended and press

5. Press

[Func] to display the Function menu.

6. Press to select Prepend.

7. Enter the prepend digits (area code or feature activation

code) by pressing the digit keys.

•

For feature calls, press before dialing the feature code.

8. Press to dial the prepended number.

Four-digit dialing

When you dial any four continuous digits of a stored phone number, your phone will redial the matched number on the display and dial the phone number.

Dial any four continuous digits.

The matched phone number(s) will be recalled and dialed up automatically.

Scroll through the displayed phone numbers to highlight the desired number.

Press to dial.

Note

If more than one phone number containing the same four digits are found in the phone book, those candidates list will be displayed.

Pause dialing

When you call automated systems (like banking services), you are often required to enter a password or account number. Instead of manually entering the numbers each time, you can store the numbers in your phone book, separated by special characters called pauses.

There are two kinds of pauses that can be entered on your phone:

• “Hard pause” stops the dialing sequence until you press .

• Timed pause (two-second pause) stops the dialing sequence for

two seconds and then automatically sends the remaining digits.

Your phone has two pause dialing methods:

• Pause dialing from the phone book (P.37)

• Manual pause dialing (P.38).

Note

Multiple two second pauses can be entered to extend the length of a pause. For example, two consecutive two second pauses gives a total pause time of four seconds.

However, keep in mind that pauses are counted as digits towards the 32 digit dialing maximum.

Tip

Refer to page 77 for storing pauses in the phone book entry.

Dialing a phone number stored with a Time pause

1. Dial the phone number with a Time pause by recalling

the phone book entry.

Two seconds after the connection is established, the Time pause will be transmitted. During the transmission, the message “SENDING DTMF” will flash on the screen.

Dialing a phone number stored with a Hard pause

1. Dial the phone number with a Time pause by recalling

the phone book entry.

The entry prompt for your credit card number, bank account number, etc. will be displayed.

Press to transmit the number (DTMF tone).

During the transmission, the message “SENDING DTMF” will flash on the screen.

Dialing the phone number by entering the pause manually

1. Enter the phone number of the service you want to call

(example: bank’s teleservice phone number (an 800 number)).

Press [Func] to display the Function menu.

Press the digit keys to select the option:

To enter a Hard Pause, press . The initial “H” will be displayed.

Enter the phone number.

Press .

After the connection is established, press again. The phone number will be sent.

To enter a Timed pause, press . The letter “T” will be displayed at the end of the phone

number.

Enter the number followed by the pause (such as your account number).

Press . Two seconds after the connection is established, the

number will be sent.

Note

We recommend you to store the frequently used phone numbers including the pause in your phone book.

Data/Fax transmission

* Model name : XN-CPA10

Using this feature, you can send and receive faxes and data by connecting your phone with a PC.

Details of setting this feature are given on page xx.

Note

You must first activate the Fax/Data service setting depending on your home network and your Internet service provider.

Requirements:

Fax/Data service

Software for Data/Fax transmission

(Optional PC connection kit including cable and CD-ROM)

Sending Fax/Data

Note

You can not receive voice mails while your phone is in FAX/Data transmission mode.

When the connection between your phone and a PC is established, you can see the following soft key menu(s) on the display.

Left soft key: xxx Right soft key: xxx???

Start the transmission application program.

Press [xxx] on your phone.

Your phone will enter Fax/Data transmission mode.

To return to a normal voice call mode, refer to page 75 (7-3. Data/ Fax).

Transmission specifications

Modem: xxx Facsimile: xxx

Menus

Menus allow you to check your phone’s settings and change the settings.

Your phone provides a Main menu (P.105) and an In-Use menu.

Main menu

The Main menu has seven categories you can access in Standby mode. Each category has its own submenus:

1 Phone Book 5 Secu rity 2 Calls 6 Setup/Tool 3 Sounds 7 System 4 Display

In-Use menu

The In-Use menu has five options you can access in Talk mode:

1 Phone Book 2 Calls 3 Sounds 4 Display 5 Setup/Tool

Note

Security and System menus are displayed, but not effective as an In-Use menu.

Menu selection

Method 1:

To select the Main menu options, press and then press the navigation keys to scroll through menu options until the desired option is displayed.

Method 2:

To select the desired submenu directly, press or press the digit key for the submenu’s number.

Submenu’s number

Note

1-4. one-touch dial

1-5. My phone #

1-6. Scratch book

When you close the active-flip or when none of the keys has been pressed for 60 seconds, the phone will automatically return to Standby mode.

1. Phone Book menu

1-1. Find by Name 1-2. Find by Group 1-3. Find Entry #

1-1./1-2./1-3.

See page 82 for the details of searching phone books.

1-4. Setting one-touch dial

You can set the stored phone book data as a one-touch dial.

Press [MEMU] to display the Main menu.

Press to select Phone Book.

Press to select One-touch Dial. The names stored in the phone book will be displayed.

Select the desired blank number and press [Func]. The Function menu will be displayed.

Press to select Set. The phone book menu will be displayed.

•

To cancel setting, press .

Search for the desired phone num ber to be set. Details of searching for the phone number are given on

page 82.

Press [Set]. The selected phone number will be saved.

1-5. Displaying my phone number

Press [MEMU] to display the Main menu.

2. Press to select Phone Book.

3. Press to select My Phone #.

4. Press to return to Standby mode.

Note

During a call, you can also display your phone number in the same manner.

Press [MEMU] to display the In-Use menu.

Press to select Phone Book menu.

3. Press to select My Phone #.

4. Press

twice to return to the Calling screen.

2. Calls menu

2-1. Call logs

Press [MEMU] to display the Main menu.

Press to select Calls

3. Press to select Call Logs.

The outgoing call logs will be displayed.

4. To display the missed call logs, press [Missed].

5. Then, to display the incoming call logs, press

[Incom].

6. To display the outgoing call logs again, press

[Outgo]. The display will switch in this order.

2-2. Call info

Details of displaying call logs and call info (last call, home calls, roam calls and all calls) are given on page 90.

3. Sounds menu

3-1 Volume

This option allows you to set the ringer volume for voice and fax calls.

There are two ways to set the ringer volume: either set in Standby mode or set in the Main menu.

In Standby mode

Press or until the desired volume is

selected.

Silent, Level 1 through 5, and Escalate. The selected value is effective immediately after you

select it.

In the Main menu

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Volume.

Press to select Normal Ringer.

Select one of the following:

Silent, Level 1 through 5 and Escalate. When selecting is complete, press [OK] to save the

setting.

Key beep volume

This feature allows you to adjust the volume of beep tone (key tone) you hear when you press a key.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Volume.

Press to select Key Beep.

Press the navigation keys to display and play the options:

Silent, level 1, level 2, level 3, and level 4. When selecting is complete, press [OK] to save the

setting.

Earpiece

This feature allows you to adjust the volume of earpiece attached to your phone.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Volume.

Press to select Earpiece.

Press the navigation keys to display and play the options:

Level 1, level 2, level 3, level 4 and level 5. When selecting is complete, press [OK] to save the

setting.

Setting ringer volume for message calls

You can select a unique ringer volume for incoming message calls.

This volume setting applies to incoming voicemail notifications, text messages and numeric pages.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Volume.

Press to select Message.

Select one of the following:

Silent, level 1 through 5 and Escalate When selecting is complete, press [OK] to save the

setting.

Setting the ringer volume for Alarm/Reminder

This feature enables you to select a unique ringer volume for your alarm and Reminder.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Volume.

Press to select Alarm/Reminder .

Select one of the following:

Level 1 through 5, and Escalate. When selecting is complete, press [OK] to save the

setting.

3-2. Silent mode

This feature allows you to silence the ringer tone and incoming message tones. You can also use the Silent key on the left side of the phone while your phone is ringing.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Silent Mode.

Press to select ON or to select OFF.

When selecting is complete, press [OK] to save the setting.

3-3. Ringer type

Using the ringer type option, you can customize your phone book setting by setting a different ringer type for each phone book entry.

When the other party has subscribed to Caller ID service, a unique ringer tone can be specified.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Ringer Type.

Press to select Set.

Press .

Use or to choose the desired type among

•

five types of ringer tone and fifteen types of melody.

Each time you switch the selection, you hear the demo.

When selecting is complete, press [OK] to save the setting.

Confirming the current setting

Press Confirm in step 4 above.

Press to select Normal Ringer.

The current setting will be displayed.

Setting ringer type for message calls

This option allows you to specify a unique ringer type for an incoming message call: a unique ringer type for voicemail notification, text messages, numeric pages and Web messages.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Ringer Type.

Press to set the ringer type.

Press to select Message Ringer.

Use or to choose the desired type among five

types of ringer tone and fifteen types of melody. Each time you switch the selection, you hear the demo.

When selecting is complete, press [OK] to save the

setting.

Confirming the current setting

Press Confirm in step 4 above.

Press to select Message Ringer.

The current setting will be displayed.

Setting ringer type for the Alarm/Reminder

This option enables you to set a unique ringer type for your Alarm and Reminder.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Ringer Type.

Press to set the ringer type.

Press to select Alarm/Reminder.

Use or to choose the desired type among five

types of ringer tone and fifteen types of melody. Each time you switch the selection, you hear the demo.

When selecting is complete, press [OK] to save the

setting.

Confirming the current setting

Press Confirm in step 4 above.

Press to select Alarm/Reminder.

The current setting will be displayed.

3-4. Vibrator

This option enables you to set a vibrator option for three ringer types: Normal ringer, Message ringer, Alarm/Reminder.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Vibrator.

Press to set the Normal Ringer,

• Press to select Message Ringer or

Press to select Alarm/Reminder.

5. Press to select ON or to select OFF.

Press numeric keys to choose the desired time between 2 to 99 seconds

6. When setting is complete, press [OK] to save the

setting.

3-5. Ringer time

This option enables you to set a ringer time (between 2 and 99 seconds) for Message ringer, Alarm/Reminder.

Press [MEMU] to display the Main menu.

Press to select Sounds.

3. Press to select Ringer Time.

4. Press to select Message Ringer, or

Press to select Alarm/Reminder.

5. Use or to choose the desired time between 2

and 99 seconds.

6. When setting is complete, press [OK] to save the

setting.

3-6. Alerts

Fade alert

This option enables you to let the alert tone fade out gradually.

Press [MEMU] to display the Main menu in Standby mode before making a call.

Press to select Sounds.

3. Press to select Alerts.

4. Press to select Fade Alert.

5. Press to select ON or to select OFF

6. When setting is complete, press [OK] to save the

setting.

Minute alert

You can set the minute beep option to sound an alert 10 seconds before every minute to remind you of the length of the current call.

Turning the minute beep on or off

Press [MEMU] to display the Main menu in

Standby mode before placing the call.

Press to select Sounds.

Press to select Alerts.

Press to select Minute Beep.

Press to select ON or to select OFF

When setting is complete, press [OK] to save the

setting.

Service alert

Your phone will beep in the following situations:

• when a dropped call or a failed call is found, or

when your phone enters or leaves a service area.

Turning the service alert on or off

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Alerts.

Press to select Service Alert.

Press to select ON or to select OFF.

Wake-up tone

When you turn on the phone, you hear a tone (wake-up tone) followed by the wakeup screen.

Turning the Wake-up tone on or of f

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Alerts.

Press to select Wakeup Tone.

Press to select ON or to select OFF.

3-7. Tone length

The tone length setting will be used to change the length (short or long) of the DTMF (dual-tone multi-frequency) tones.

The tone length depends in the tele-service system used by the bank or other service (such as a bank account or voicemail system).

Consult tele-service center (?) you will use for details of the tone length.

Press [MEMU] to display the Main menu.

Press to select Sounds.

Press to select Tone Length.

Press to select Normal or to select Long.

4. Display menu

4-1. LCD contrast

You can adjust the brightness (or contrast) of backlight in 9 steps.

Press [MEMU] to display the Main menu.

Press to select Display.

Press to select LCD Contrast.

Press (Dark) or (Light).

Up to nine levels are available.

•

When the desired contrast is displayed, press [OK] to save the setting.

4-2. Backlight

You can turn the backlight on or off, or adjust the length of backlighting. You can save the battery power if you turn the backlight setting off. When you select the length of backlighting, the backlight will goes off after the selected times of interval.

Press [MEMU] to display the Main menu.

Press to select Display.

Press to select Backlight.

Press one of the following:

Always OFF 8 seconds 15 seconds 30 seconds

Always ON

Note

This setting is also valid when the phone is attached to the optional handsfree car kit.

4-3. Input mode

This feature allows you to select input method, automatic hyphenation or T9.

Automatic hyphenation

Automatic hyphenation follows the North American Numbering Plan, which hyphenates numbers as follows:

800-555-1234 A digit following a pause will not be hyphenated. (P.36 “Pause

dialing”) Details of T9 input method are given on page 79.

Press [MEMU] to display the Main menu.

Press to select Display.

Press to select Input Mode.

Press to select Auto Hyphen or to select T9.

Press to select ON or to select OFF.

4-4. Banner

Your phone can display a banner up to 100 characters in Standby mode while the phone is on.

The default setting (“Welcome”) can be customized within the specified 100 characters.

Press [MEMU] to display the Main menu.

Press to select Display.

Press to select Banner.

Press to select Enter your Message or to

select Inbox Message from.

• Enter your Message

The default setting (“Welcome”) will be displayed. Edit the current message as you desire. Up to 100 characters can

be entered. Press [OK] to save the setting.

• Inbox Message from

Message source will be displayed: E-mail address and number.

• Enter E-mail Address

Press . The address entry prompt will be displayed. Enter the desired phone address

• Enter number

Press . The number entry prompt will be displayed. Enter the desired number.

Press [OK] to save the setting.

Press to return to Standby mode.

The message will be displayed while your phone is on.

4-5. Graphic

This feature allows you to select your desired graphic image for the following situations:

Press [MEMU] to display the Main menu.

Press to select Display.

Press to select Graphic.

Press each key to select the desired graphic image.

•

Press to select Wallpaper. The following selections will be displayed.

01 OFF 02 Dolphin 03 Flower 04 Bee 05 Good Bye 06 Send OK 07 Send NG 08 Connecting 09 Sending 10 Receiving 11 Searching 12 PHOTO1 13 PHOTO2 14 Water 15 Alarm 16 Receive1 17 Receive2 18 Receive3 19 Receive4 20 Receive5

• Press to select Standby

The following selections will be displayed. 01 Water 02 Alarm 03 Receive1 04 Receive2 05 Receive3 06 Receive4 07 Receive5

• Press to select Incoming Call

The following selections will be displayed. 01 Water 02 Alarm 03 Receive1 04 Receive2 05 Receive3 06 Receive4 07 Receive5

• Press to select Custom

The following selections will be displayed.

[1] ---------[2] ---------[3] ---------[4] ---------[5] ----------

• Press to select Connecting The following selections will be displayed. 01 Good Bye 02 Send OK

03 Send NG 04 Connecting 05 Sending 06 Receiving 07 Searching 08 PHOTO 1 09 PHOTO 2 10 Water 11 Alarm 12 Receive1 13 Receive2 14 Receive3 15 Receive4 16 Receive5

• Press to select Alarm/Reminder The following selections will be displayed. 01 Water 02 Alarm

03 Receive1 04 Receive2 05 Receive3 06 Receive4 07 Receive5

• Press to select Wakeup

The following selections will be displayed. 01 Good Bye 02 Send OK 03 Send NG 04 Connecting 05 Sending 06 Receiving 07 Searching 08 PHOTO 1 09 PHOTO 2 10 Water 11 Alarm 12 Receive1 13 Receive2 14 Receive3 15 Receive4 16 Receive5

• Press to select Good-bye

The following selections will be displayed. 01 Good Bye 02 Send OK 03 Send NG 04 Connecting 05 Sending 06 Receiving 07 Searching 08 PHOTO 1 09 PHOTO 2 10 Water

11 Alarm 12 Receive1 13 Receive2 14 Receive3 15 Receive4 16 Receive5

Use or to select the desired wallpaper.

Press [OK]. The selected wallpaper will be displayed.

Press [OK] to save the setting.

4-6. Information

You can display your phone’s software version, hardware version,

ESN

and PRL*. These items of information are needed for you to

call your home network Customer Care. * ESN: Electronic Serial number * P RL: Preferred Roaming List * NAM: Number Assignment Module

Press [MEMU] to display the Main menu.

Press to select Display.

Press to select Information.

Press to select Version. The hardware, software version, ESN and PRL will be

displayed.

Press to select NAM name.

Press to return to the

Information menu

screen.

5. Security menu

To protect your phone from unauthorized use, you can lock it easily in the Main menu, and unlock it as well.

To lock your phone, a 4-digit lock code must be entered. The factory default setting of the lock code is 0000 or last 4 digits of your phone number.

Once you have entered the lock number, you must enter it when you want to change the Security menu settings.

Note

Regardless of whether the phone is locked or not, you can dial emergency numbers (911, 911 and #911) and three specified numbers (P.63 “special numbers”), and answer incoming calls as well.

5-1. Lock mode

1. Lock ON power up

This feature allows you to lock the phone every time you turn it on.

1.Press [MEMU] to display the Main menu.

Press to select Security and enter your current lock code .

Press to select Lock Mode. Press the navigation keys to select an option:

•

Lock ON Power Up: The phone will be

automatically locked when you turn it on.

•

Lock Now: The phone locks immediately and

stays locked until the lock code is entered.

•

Unlocked: The phone remains unlocked. (See

below)

Press

2. Lock now (see above)

to save the setting.

[OK]

3. Unlock

Press [MEMU] to display the Main menu.

Press to select Security.

Enter the 4-digit password.

When it is matched, the next screen will be displayed. Select to select Lock Mode.

Press to select Unlock.

Press [OK].

The phone will be unlocked immediately.

5-2. New code

The default lock code for your Phone is set to either 0000 or the last four digits of your phone number. You can set a unique lock code and change the lock code if necessary.

Entering a new lock code:

Press [MEMU] to display the Main menu.

Press to select Security and enter your current lock

code. Press to select New Code.

Enter a new, four-digit lock code by pressing the digit

keys. The lock code will be replaced with the

your phone from unauthorized use. Press [OK] to save the new lock code.

To cancel entering a new code, press or .

•

mark preventing

5-3. Emergency # (Special numbers)

Special numbers (Emergency #)

You can store three phone numbers (Special Numbers) to be dialed up even when the phone is in Lock mode.

And once you store these numbers in the phone book, they can be dialed manually.

Storing special numbers

Press [MEMU] to display the Main menu.

Press to select Security and enter your current lock

code. Press to select Emergency #.

To select a location to store the special number:

Press to select Emergency 1,

•

Press to select Emergency 2,

•

Press to select Emergency 3.

•

Select to select Enter number or to select

Search Phone book.

[1] Enter Number

Enter the special number by using the digit keys. Press [OK] to save the number in the selected location.

[2] Search Phone Book

Perform the search procedure explained on page 82. Choose the desired name and press [OK]. The contact of the selected name will be displayed. Press [OK] to save the number in the selected location.

5-4. Erase all

menu screen (step 4).

You can erase all numbers stored in your phone book data, messages and call logs.

Press [MEMU] to display the Main menu.

Press to select Security and enter your current lock code.

Press to select Erase All

Press to select Phone Book. A confirmation message will be displayed to ask if you are

sure you want to erase the entire phone book data.

Press to select Call Logs.

•

Press to select Messages.

•

Select to select Phone Book. A confirmation message will be displayed

Select to select YES. The final confirmation message will be displayed.

Select . When erasing has been completed, “Erased!” will be

displayed and the phone will return to the Erase all

5-5. Secret memory

Details of setting secret memory are given on page 81.

5-6. Reset

In case of misoperation or failure due to some problem, you need to reset all settings of your phone to the factory defaults.

Note

When resetting your phone, we recommend you to save or download your important settings (phone book data) to a PC using the optional Phone Book utility software (sold separately) for your safety. (P.39)

However, phone book data, messages, and call logs will remain in memory.

Press [MEMU] to display the Main menu

Press to select Security and enter your current lock code.

Press to select Reset.

Select to select OK. A confirmation message will be displayed to ask if you are

sure you want to reset the phone.

Select to select YES.

Press [OK] to execute resetting. After resetting is complete, the phone will be restarted and

enter Standby mode. During resetting, “Now Resetting...” will be displayed.

•

To cancel resetting, press to select Cancel in step 4, or press to select NO in step 5.

6. Setup/Tool menu

6-1. Memory status

This feature helps you to view the memory status of the following records.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Memory Status. The following records will be displayed:

Phone Book xxx/300 Items Message xxx % Browser data xxx %

Download xxx %

6-2. Calling

Turning the Auto answer option on or off. This option sets your phone to automatically answer a call after

one ring.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Calling.

Press to select Auto Answer.

Press to select ON or to select OFF.

Press [OK] to save the setting.

Turning the Any key answer option on or off

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Calling.

Press to select Any Key Answer.

Press to select ON or to select OFF.

Press [OK] to save the setting.

Turning the Auto retry option on or off

This feature helps you let your phone redial automatically up to five times after the specified length of time, until your call will be picked up.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Calling.

Press to select Auto Retry.

The options will be displayed. Press to select Every 60 sec.

Press to select Every 30 sec.

•

Press to select OFF.

•

The Auto retry option will be turned off. Press [OK] to save the setting.

Voice privacy

< Network and service dependent feature >

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Calling.

Press to select Voice Privacy.

Press to select Automatic.

Press to select Enhanced.

•

Press [OK] to save the setting.

6-3. Voice mail

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Voicemail.

xxxxxx

Press [OK] to save the setting.

6-4. Message

1. Callback #

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Message.

Press to select Callback #.

Enter the desired phone number.

Press [OK] to save the setting.

2. Delivery ACK

You can send the acknowledgement to the sending end when you receive the incoming data successfully.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Message.

Press to select Delivery ACK.

Press to select ON with notification.

You can check the notification message on the display that

acknowledgement is sent.

the

Press to select ON.

•

You can send the message

•

Press [OK] to save the setting.

Press to select OFF.

acknowledgement without

notification

3. Canned messages

You can edit or add the fixed forms used when sending messages.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Message.

Press to select Canned Message.

The selections will be displayed:

[1] Yes [2] No [3] Call me [4] need direction [5] Where are you [6] I’ll call later [7] Busy [8] On my way [9] I’ll arrive soon [10] Thank you [11] Meeting cancel! [12] Meet me at [13] Call me at [14] Please help! [15] -------------[16] -------------[17] -------------[18] -------------[19] -------------[20] --------------

6-5. Browser

OFF

Details of setting the charged time display are given on page 97.

6-6. Alarm

Alarm Clock Setting the daily alarm

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Select to select Alarm.

Press [OK].

Select to select Daily Alarm.

Press to select ON.

Press [OK].

Enter the alarm time.

Use the digit keys and press or to set AM or PM.

Press [OK] to save the setting.

Deleting the dairy alarm setting

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Select to select Alarm.

Press to select Dairy Alarm.

Select to select Alarm.

Press [OK].

Press to8.select

Press . The phone will return to Standby mode.

Call Reminder Setting the Call reminder

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select Alarm.

Press to select Call Reminder.

Press to select ON.

Select the search method from one of the following:

[1] to select Search Phone Book

•

[2] to select Search Call Logs

•

[3] to select Enter Name

•

Press [OK].

Enter the time for the alarm by using the digits keys.

Press or key to select AM or PM.

Press [OK] to save the Call Reminder setting.

Disabling the Call reminder setting

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Select to select Alarm.

Press to select Call Reminder.

Press to select ON.

Press [Remove].

Press to select YES.

To cancel removing the setting, press to select NO.

•

6-7. Clock setting

1. Clock

This feature allows you to set the current date and time. The factory default setting is “January 1. 2001.”

Automatic setting provided by the radio network takes priority over the manual setting.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Select to select Clock Setting.

Select to select Clock.

The following clock format will be displayed:

Date (M/D/Y)

0 0 / 0 0 / 0 0 0 0

Time (H:M)

12:00 AM (PM)

Use and to set the current date and time.

Press [OK] to save the setting.

2. Time zone

This feature allows you to select the time zone you belong to. The selections are:

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Select to select Clock Setting.

Select to select Time Zone.

The following options will be displayed:

[1] Auto (Your phone will automatically detect the appropriate

time zone depending on your location.)

[2] AST (Alaska Standard Time)

[3] EST (Eastern Standard Time) [4] CST (Central Standard Time) [5] MST (Mountain Standard Time) [6] PST (Pacific Standard Time) [7] AKST (Alaska Standard Time) [8] AIST (Hawaii-Aleutian Standard Time)

Select Auto or your own and press [OK].

Press [OK] to save the setting.

6-8. Data

This feature allows you to transmit the data.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Select to select Data.

xxx

6-9. PC link

This feature allows you to transmit data between your phone and a PC, enabling a PC connection with the specified connection cable.

Press [MEMU] to display the Main menu.

Press to select Setup/Tool.

Press to select PC Link.

Press [OK].

Press to enter a PC link mode or press

cancel setting.

7. System menu

7-1. Set service

Details of setting Set service are given on page 24.

7-2. Force mode

Press [MEMU] to display the Main menu.

Press to select System.

Press to select Force mode.

Press to select Automatic,

Press to select CDMA only,

•

Press to select PCS only,

•

Press to select CELL only.

•

Press [OK] to save the setting.

7-3. Data/Fax

Press [MEMU] to display the Main menu.

Press to select System.

Press to select Data/Fax.

Press to select Automatic,

Press to select CDMA only,

•

Press to select PCS only,

•

Press [OK] to save the setting.

7-4. Call guard

Details of setting Call guard are given on page 25.

Phone Book Dialing

Your phone can store up to 300 phone numbers.

Phone book entries: Up to 300 Phone number: 32 digits including hard pauses and Timed pauses Name: Up to 16 characters E-mail address: Up to 48 characters Group: 10 groups (9 customizable groups + default) Label: (None), Home, Work, Mobile, Pager, Fax

* Group names can not be changed.

Tip

• You can store the phone number as a hidden number to protect it from unauthorized use. (P.81)

• Up to 9 One-touch dialing can be asigned from the phone book data. (P.41 One-touch dialing)

Storing a phone number and name

Press [MENU] to display the Main menu.

Press to select Phone Book.

Press [New].

The name entry prompt will be displayed.

Enter a name and press [OK].

See page 78 for details on entering characters. Select a desired label for a new entry and press

[OK].

[1] None, [2] Home, [3] Work, [4] Mobile, [5] Pager and

•

[6] Fax

Press the and keys to highlight the number

item and press [OK] to enter the phone number. The phone number prompt will be displayed.

Press the digit keys to enter the phone number.

8. If necessary, press to enter a hard pause ([1] key) or

a time pause ([2] key).

9. Press [OK].

The next item (E-mail address) will be highlighted.

10. Press [OK].

The e-mail address entry prompt will be displayed.

11. Enter the e-mail address.

Up to 48 characters can be entered.

•

12. Press [OK].

The next item (Memory #) will be highlighted.

13. Press [OK].

14. Enter the desired number (3-digit) and press [OK] to

save the setting.

•

If a warning message is displayed to indicate you are going to overwrite a location, enter another number and press [OK].

Storing phone numbers with pauses

Enter the phone number you want to store (such as the bank’s teleservice phone number).

Press [Func] to display Function menu.

•

Press or to enter the desired pause: – To enter a Hard Pause, press .

The letter “H” will be displayed at the end of the number. Then enter the digits followed by the pause (such as your account number), or

– To enter a Timed pause, press .

The letter “T” will be displayed at the end of the phone number. Then enter the number followed by the pause (such as your account number).

3. Store the phone number by pressing [Store].

4. Follow the screen prompt.

Entering characters

When entering characters (letter, number or punctuation) to create phone book entries, press the corresponding key.

Pressing each key scrolls characters in the following order when the input method is set to “Multi tap” (default).

Available characters in Multi tap mode

.(period) , (comma) ? ! - (hyphen) ‘ (apostrophe) @ : 1 a b c A B C 2 d e f D E F 3

g h i G H I 4 j k l J K L 5 m n o M N O 6 p q r s 7 P Q R S

t u v 8 T U V

w x y z 9 W X Y Z

(Moving the cursor to the right) (Performing the same function as the left soft key)

• To enter uppercase letters, press the left soft key until is

displayed.

• To enter the first letter of the name, etc. in uppercase, press the

left soft key until is displayed.

• To correct the last character, press briefly.

Press and hold it to clear all characters.

Changing the input modes

By choosing the desired input mode and selecting edit options on the entry prompt screen, you can reduce input time. Press on the entry prompt screen.

Input mode and edit options will be displayed: [1] T9 (Multi tap), [2] Numeric (Multi tap), [3] Symbol, [4] Canned Message (P.70), [5] Copy, [6] Cut, [7] Paste

T9 text input

T9 text input method is a shortcut to enter text easily and quickly. When you enter a letter “how”, you press the corresponding digit

keys several times until each letter is displayed. By using T9, you press only . T9 scans and

recognizes your keystrokes, and displays the frequently and commonly used letters automatically. (You can change the candidates by pressing until the desired is displayed. T9 will display other candidates by analyzing the combinations of the keys pressed.)

For example, this method helps you complete mail messages quickly.

• To return to the normal input mode (Multi tap), press

[Func] and select [1] (Multi tap).

Symbol

To enter symbols, press [Func] and select [3] (Symbol). Select the desired symbol and press [OK].

Canned Message

To enter fixed text, press [Func] and select [4] (Canned Message).

Select the desired text and press [OK].

• Canned messages can be edited in the Main menu. (6. Setup/

Tool/P.70)

Overwriting an existing location

You can change the existing data with a new phone number or change a part of the stored data.

Press [MENU] to display the Main menu.

Press to select Phone Book.

Perform the search function and select the desired entry.

Press [OK]. The personal contact will be displayed.

Press [Func] to display the Function menu.

Press to select EDIT.

If necessary, change the desired entry.

Press [Save] to save the setting.

Enter the memory number and press [OK].

Note

If the desired memory location already contains an entry, the phone displays a message asking if you want to replace the current entry. To replace the entry, press [OK].

To return to the previous screen and select another location, press . You can only use each label one time for each stored name (for example, you can only have one name labeled Work for a name entry).

If you want to shortcut the way to store a phone number...

Enter the phone number.

Press [Store].

Repeat the steps 5 through 14 for “Storing a phone number and name” (page 76).

Tip

You can quickly store the phone number using the incoming or outgoing call logs. (P.89)

Storing a phone number with a group setting (Property1)

1. Repeat the steps of storing a phone number and name step14

on page 76 to 77.

Press [Func].

The Function menu will be displayed. Press to select [Property1].

Press to select [Gr: (current setting)] and press

[OK].

Press the desired number and press [OK].

The setting will be displayed.

Storing a phone number as a secret memory (Property1)

1. Repeat the steps of storing a phone number and name step 14

on page 76 to 77.

Press [Func].

The Function menu will be displayed. Press to select [Property1].

Press to select [Secret] and press [OK].

Press to select ON or [2] to select OFF and press

[OK].

The setting will be displayed.

Property2 (One-touch dial, Custom tone, Custom graphics)

Searching for phone numbers

Three methods of searching for phone numbers are available:

Finding by Name

Press [MENU] to display the Main menu.

Press to select Phone Book.

Press to select Find by Name.

Enter up to 16 characters to be found. Matched results will be displayed alphabetically.

Scroll the list using and , if necessary.

When the desired entry is found, press [OK].

Press to dial.

Finding by Group

Press [MENU] to display the Main menu.

Press to select Phone Book.

Press to select Find by Group. The group names will be displayed:

•

[0] Unfiled, [1] Personal 1, [2] Personal 2, [3] Personal 3, [4] Business 1, [5] Business 2, [6] Business 3, [7] Others 1, [8] Others 2, [9] Service

Press the desired digit keys or use or to locate the entry.

When the desired entry is found, press [OK].

Press to dial.

Finding Entry #

Enter Entry # which you desired, and press [ M ].

1. Press [MENU] to display the Main menu.

Press to select Phone Book.

Press to select Find Entry #.

Press the desired digit keys or use or to locate

the entry. When the desired entry is found, press [OK].

Press to dial.

Adding a Name Ringer

You can link your phone book entries with 20 kinds of ringer tones (fifteen melodies and five tones).

You can know who is calling identifying the ringer or melody

preset to Phone book.

Press [MENU] to display the Main menu.

Press to select Sounds.

Press to select Ringer Type.

Press to select Set.

Choose one of the 5 options ([4] to [8]) and press [OK].

The phone number search prompt will be displayed.

Choose an entry and press [Set].

Choose the desired melody.

When selecting is complete, press [OK] to save the setting.

Confirming the current setting

Press Confirm in step 4 above.

Press to select Normal Ringer. The current setting will be displayed.

Sharp HRO00022 Users Manual

Specifications and Main Features

Frequently Asked Questions

User Manual