Sharp UX-8, GQ-5, FO-50, UX-40 Service Manual

Download

Page 1

UX-8TH/UX-40TH GQ-5TH/FO-50TH

No. 00ZUX8TH//SME

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications ............................................ 1-1

[2] Operation panel......................................... 1-2

[3] T ransmittab le documents .......................... 1-3

[4] Installation ................................................. 1-4

[5] Quick reference guide ............................... 1-9

CHAPTER 2. ADJUSTMENTS

[1] Adjustments .............................................. 2-1

[2] Diagnostics and service soft switch .......... 2-2

[3] T roubleshooting...................................... 2-18

[4] Error code table....................................... 2-19

CHAPTER 3. MECHANISM BLOCKS

[1] General description ................................... 3-1

[2] Disassembly and assembly

procedures ....................................... 3-3

CHAPTER 4. DIAGRAMS

[1] Block diagram ............................................4-1

[2] Wiring diagram .......................................... 4-2

[3] Point-to-point diagram ............................... 4-3

CHAPTER 5. CIRCUIT DESCRIPTION

[1] Refer to the service manual of UX-60TH. [2] Refer to the service manual of UX-60TH. [3] Refer to the service manual of UX-60TH. [4] Refer to the service manual of UX-60TH. [5] Refer to the service manual of UX-60TH.

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT

[1] Control PWB circuit ................................... 6-1

[2] TEL/LIU PWB circuit.................................. 6-9

[3] Power supply PWB circuit ...................... 6-13

[4] Operation panel PWB circuit ................... 6-15

CHAPTER 7. OPERATION FLOWCHART

[1] Refer to the service manual of UX-60TH. [2] Refer to the service manual of UX-60TH.

CHAPTER 8. OTHERS

[1] Refer to the service manual of UX-60TH. [2] Refer to the service manual of UX-60TH. PARTS GUIDE

CONTENTS

FACSIMILE

UX-8

UX-40 GQ-5

MODEL FO-50

Parts marked with " " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for after sales service only. The contents are subject to change without notice.

SHARP CORPORATION

SERVICE MANUAL

Illustration: UX-8

This service manual is omitted because it is partly common to UX-60TH/FO-70TH of the ser vice manual of the previous issue. Those common parts are to refer to the service manual of UX-60TH/FO-70TH (00ZUX60TH/SME).

Page 2

UX-8TH/UX-40TH GQ-5TH/FO-50TH

(Danish) ADVARSEL !

Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteri af samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

(English) Caution !

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type

recommended by the equipment manufacturer.

Discard used batteries according to manufacturer’s

instructions.

(Finnish) VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaan

tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French) ATTENTION

Il y a danger d’explosion s’ il y a remplacement incorrect

de la batterie. Remplacer uniquement avec une batterie du

même type ou d’un type recommandé par le constructeur.

Mettre au rébut les batteries usagées conformément aux

instructions du fabricant.

(Swedish) VARNING

Explosionsfare vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalent

typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens

instruktion.

(German) Achtung

Explosionsgefahr bei Verwendung inkorrekter Batterien.

Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder

vom Hersteller empfohlene Batterien verwendet werden.

Entsorgung der gebrauchten Batterien nur nach den vom

Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY REPLACEMENT

Page 3

1 – 1

UX-8TH/UX-40TH GQ-5TH/FO-50TH

CHAPTER 1. GENERAL DESCRIPTION

[1] Specifications

Automatic dialing: Rapid Key Dialing: 5 numbers

(Note for UX-8/GQ-5: Rapid Key Dialing is not available) Speed Dialing: 35 numbers (Note for UX-8/GQ-5: 10 number)

Fax paper: Initial starter roll (included with machine):

10 m Recommended replacement roll: FO-20PRw, 30m, 12.7mm core

Paper cutting method: Tear off by hand Modem speed: 9600 bps with automatic fallback to lower

speeds

Transmission time* : Approx. 15 seconds Resolution: Horizontal: 8 dots/mm

Vertical:

Standard: 3.85 lines/mm Fine/Halftone: 7.7 lines/mm Super fine: 15.4 lines/mm

Automatic document feeder: 5 pages max. (20 lb paper)

(UX-8/GQ-5: This function is not available)

Halftone (grayscale): 64 levels Display: 16-digit LCD display Compression scheme: MR, MH, Sharp (H2) Applicable telephone line: Public switched telephone network Compatibility: ITU-T (CCITT) G3 mode Input document size: Automatic feeding:

Width: 148 to 216 mm Length: 140 to 297 mm

Manual feeding:

Width: 148 to 216 mm Length: 140 to 600 mm

Effective scanning width: 210 mm max. Effective printing width: 210 mm max. Contrast control: Automatic/Dark selectable Reception modes: Fax, T el, Tel/Fax, A.M. Copy function: Yes Telephone function: Yes (cannot be used if power fails) Power requirements: 220-240 V AC, 50/60 Hz Operating temperature: 5 - 35°C Humidity: Maximum: 85 % RH Power consumption: Standby: 2.3 W

Maximum: 115 W

Dimensions: Width: 304 mm

Depth: 236 mm

Height: 122 mm Weight: Approx. 2.6 kg * Based on ITU-T (CCITT) Test Chart #1 at standard resolution in Sharp

special mode, excluding time for protocol signals (i.e., ITU-T phase C time only).

Note: The facsimile machine is Year 2000 compliant.

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.

Page 4

1 – 2

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[2] Operation panel

1. Rapid Dial keys

Press one of these keys to dial a fax number automatically. Note for UX-8/GQ-5: Rapid Key Dialing is not available.

2. Display

This displays messages and prompts during operation and programming.

3. FUNCTION key

Press this key to select various special functions.

4. VOLUME keys

Press this keys to adjust the volume of the speaker when the SPEAKER key has been pressed, the volume of the ringer at all other times.

5. Number keys

Use these keys to dial numbers, and enter numbers and letters when storing auto-dial numbers.

6. SPEED DIAL key

Press this key to dial a fax or voice number using an abbreviated 2-digit Speed Dial number.

7. REDIAL key

Press this key to automatically redial the last number dialed.

8. START key

Press this key to begin transmission when using Speed Dialing, Direct Keypad Dialing, or Normal Dialing.

9. STOP key

Press this key to cancel operation before it is completed.

10. COPY/HELP key

When a document is in the feeder, press this key to make a copy of a document. At any other time, press this key to print out the Help List, a quick reference guide to the opeation of your fax machine.

11. RESOLUTION/RECEPTION MODE key

When a document is in the feeder, press this key to adjust the resolution for faxing or copying. At any other time, press this key to select the reception mode (an arrow in the display will point to the currently selected reception mode).

12. SPEAKER key

Press this key to listen the line and fax tones through the speaker when faxing a document. Note: This is not a speakerphone. You must pick up the handset to talk with the other party.

13. HOLD/SEARCH key

Press this key to search for an auto-dial number, or, during a phone conversation, press this key to put the other party on hold.

14. Panel release

Grasp this finger hold and pull toward you to open the operation panel.

TEL FAX

RECEPTION

MODE

RESOLUTION FUNCTION

DOWN VOLUME UP

A.M.

SPEED DIAL

REDIAL

SPEAKER

10/POLL

ABC

DEF

JKL

MNO

GHI

TUV

WXYZ

PQRS

START

STOP

COPY/HELP

HOLD/SEARCH

TEL FAX

GHI

PQRS

JKL

ABC

DEF

MNO

WXYZ

TUV

STOP

COPY/

HELP

START

FUNCTION

VOLUME

SPEED

DIAL

REDIAL

HOLD/

SPEAKER

RESOLUTION/

RECEPTION MODE

654

TEL/FAX A.M.

POLL

1 4 5 62 3

11109

1314

Page 5

1 – 3

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[3] T ransmittab le documents

1. Document Sizes

* With special sizes, only one sheet can be fed into the machine at a

time. Insert next page into feeder as current page is being scanned.

2. Paper Thickness & Weight

Normal size

width 148 – 216 mm

length 140 – 297 mm

5. Automatic Document Feeder Capacity

Number of pages that can be placed into the feeder at anytime is as follows:

Normal size: max. ADF 5 sheets Special size: single sheet only (manual feed)

NOTES: • When you need to send or copy more pages than the feeder

limit, place additional pages in feeder when last page in feeder is being scanned.

• Place additional pages carefully and gently in feeder .

If force is used, double-feeding or a document jam may result.

6. Readable Width & Length

The readable width and length of a document are slightly smaller than the actual document size.

Note that characters or graphics outside the effective document scanning range will not be read.

• Readable width

210mm, max.

• Readable length

This is the length of the document sent minus 5mm from the top and bottom edges.

Use document carrier sheet for smaller documents.

Readable width

(Min.)

(Max.) A4 size

(Max.)

140mm

297mm

600mm

148mm 216mm

[

Normal size

]

216mm

[

Special size

]

3. Document Types

• Normal paper Documents handwritten in pencil (No. 2 lead or softer), fountain

pen, ball-point pen, or felt-tipped pen can be transmitted. Documents of normal contrast duplicated by a copying machine

can also be transmitted.

• Diazo copy (blue print) Diazo copy documents of a normal contrast may be transmitted.

• Carbon copy A carbon copy may be transmitted if its contrast is normal.

4. Cautions on Transmitting Documents

• Documents written in yellow, greenish yellow , or light blue ink cannot be transmitted.

• Ink, glue, and correcting fluid on documents must be dry before the documents can be transmitted.

• All clips, staples and pins must be removed from documents before transmission.

• Patched (taped) documents should be copied first on a copier and then the copies used for transmission.

• All documents should be fanned before insertion into the feeder to prevent possible double feeds.

5mm

Readable length

Paper size 148mm x 140mm ~

A4 (210mm x 297mm), Letter (216mm x 279mm)

4x6 series (788mm x 1091mm x 1000mm sheets)

Square meter series

Minimum Maximum Minimum Maximum

Feeder capacity 5 sheets, max.

Paper thickness (ref.)

0.06mm 0.09mm 0.06mm 0.09mm

Paper weight 45kg 69.2kg 52g/m

80g/m

Page 6

1 – 4

UX-8TH/UX-40TH GQ-5TH/FO-50TH

7. Use of Document Carrier Sheet

A document carrier sheet must be used for the following documents.

• Those with tears.

• Those smaller than size 148mm (W) x 140mm (L).

• Carbon-backed documents

NOTE: To transmit a carbon-backed document, insert a white sheet of

paper between the carbon back of the document and the document carrier.

• Those containing an easily separable writing substance (e.g., trac-

ing paper written on with a soft, heavy lead pencil).

NOTES: • When using the document carrier, carefully read the in-

structions written on the back.

• If the document carrier is dirty, clean it with a soft, moist

cloth, and then dry it before using for transmission.

• Do not place more than one document in the carrier at a

time.

[4] Installation

1. Site selection

T ake the f ollowing points into consideration when selecting a site f or this model.

ENVIRONMENT

• The machine must be installed on a level surface.

• Keep the machine away from air conditioners, heaters, direct sun-

light, and dust.

• Provide easy access to the front, back, and sides of the machine. In

particular, keep the area in front of the machine clear, or the original document may jam as it comes out after scanning.

• The temperature should be between 5° and 35°C.

• The humidity should be between 30% and 85% (without conden-

sation).

ELECTRICITY

220-240 V, 50/60 Hz, grounded (3-prong) AC outlet is required.

Caution!

• Connection to a power source other than that specified will cause

damage to the equipment and is not covered under the warranty.

• If your area experiences a high incidence of lightning or power surges,

we recommend that you install a surge protector for the power and telephone lines. Surge protectors can be purchased at most telephone specialty stores.

If the machine is moved from a cold to a warm place...

Condensation may from on the reading glass if machine is moved from a cold to a warm place, this will prevent proper scanning of documents for transmission. Turn on the power and wait approximately 2 hours before using machine.

TELEPHONE JACK

A standard telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices.

• Plugging the fax machine into a jac k which is not an jack may result in

damage to the machine or your telephone system. If y ou do not know what kind of jack you have , or need to hav e one installed, contact the telephone company.

2. Assembly and connections

Plug the power cord into a 220-240 V, 50/60 Hz, grounded AC outlet.

• Caution: Do not plug the power cord into an y other kind of outlet.

This will damage the machine and is not covered under the warranty.

• The machine does not have a power on/off switch, so the po wer is

turned on and off by simply plugging in or unplugging the power cord.

Direction of insertion

Make print straight across paper E.G. Place the document carrier in the document feeder with the clear film side down

Make sure the handset cord goes into the jack marked with a handset symbol on the side of the machine!

Use the handset to make ordinary phone calls, or to transmit and receive faxes manually.

Connect the handset as shown and place it on the handset rest.

♦ The ends of the handset cord are identical, so they will go into

either jack.

Attach the original document support as shown below.

Page 7

1 – 5

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Insert one end of the line cord into the jack on the back of the ma-

chine marked TEL. LINE. Insert the other end into a standard singleline wall telephone jack.

TEL. LINE

TEL. SET

Note: The fax machine is set for touch-tone dialing. If you are on a pulse dial (rotary) line, you must set the fax machine for pulse dialing. Press the keys on the operation panel as follows:

1. Press these keys:

3. Press the STOP key to return to the date

and time display.

3. Removing the packing paper

Grasp the finger hold and open the operation panel.

FUNCTION

2. Press 1 to select tone (touch-tone)

dialing, or 2 to select pulse (rotary) dialing.

TONE

PULSE

STOP

The display will show:

DIAL MODE

Flip up the front paper guide.

Remove the packing paper.

Flip down the front paper guide and then close the operation panel.

Note: Do not peel off or bend this strip of film.

Page 8

1 – 6

UX-8TH/UX-40TH GQ-5TH/FO-50TH

4. Loading the fax paper (FO-20PRw)

• Your f ax machine prints incoming faxes on a special kind of paper called fax paper.

• The fax machine’s print head creates text and images by applying heat to the fax paper.

Grasp the finger hold as shown and pull up to open the operation panel.

Flip up the front paper guide.

YES

NO!

If you are loading A4 size paper, place the paper roll shims on each side of the paper compartment.

• The ribbed side of the shims should face in (toward each other).

Unwrap the roll of fax paper and insert the paper shaft.

Click!

Insert the leading edge of the paper into the slot as shown. Continue

to push the paper through the slot until it comes out the opening in the front of the machine.

Place the roll of fax paper in the compartment, making sure the ends

of the paper shaft fit into the notches on each side of the compartment.

♦ Important: The roll must be placed so the leading edge of the

paper unrolls as shown. (The paper is only coated on one side for printing. If the roll is placed backwards, the paper will come out blank after printing.)

Make sure the paper comes out straight, and then flip down the pa-

per guide.

Close the operation panel, making sure it clicks into place.

• A shor t length of the paper will feed out. Grasp the paper by the edge and pull upward to tear it off.

Page 9

1 – 7

UX-8TH/UX-40TH GQ-5TH/FO-50TH

5. Clearing a jammed document

If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the STAR T key. If the document doesn’t f eed out, open the operation panel and remove it.

Important:

Do not try to remove a document without first releasing it as explained below. This may damage the feeder mechanism.

Grasp the finger hold and pull up to open the operation panel.

Flip up the green levers on each side of the white roller.

Remove the document.

Flip down the green levers on each side of the white roller.

Close the operation panel, making sure it clicks into place.

• Press down on both front corners of the panel to make sure it clicks into place.

Page 10

1 – 8

UX-8TH/UX-40TH GQ-5TH/FO-50TH

6. Clearing jammed paper

If the fax paper jams, PAPER JAMMED will appear in the display. Follow the steps below to clear the jam.

Grasp the finger hold and pull up to open the operation panel.

Flip up the front paper guide.

Cut off the wrinkled part of the paper.

Remove the paper roll.

Reload the paper.

• Jammed paper is often caused by improper loading. Be sure to carefully follow the instructions for paper loading given in Loading the Fax Paper.

Page 11

1 – 9

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[5] Quick reference guide

ENTERING YOUR NAME AND NUMBER

1. Press:

FUNCTION

Display shows: OWN NUMBER SET

2. Press:

3. Enter your fax number (max. of 20 digits) by pressing the number keys.

• To insert a space between digits, press the # key.

• If you make a mistake, press the SPEED DIAL k ey to bac kspace and clear the

mistake.

4. Press:

5. Enter your name by pressing the appropriate number keys as shown below.

• T o enter two letters in succession that require the same ke y , press the SPEAKER key after entering the first letter.

SENDING FAXES

RESOLUTION/

RECEPTION MODE

FAX

TEL

FAX

TEL

05 NOV 10:30

A.M.

TEL/FAX

A.M.

TEL/FAX

05 NOV 10:30

FAX

TEL

FAX

TEL

05 NOV 10:30

A.M.

TEL/FAX

A.M.

TEL/FAX

05 NOV 10:30

START

Place your document (up to 5 pages) face down in the document feeder. (UX-8/GQ-5: Only one page can be loaded at a time.)

Normal Dialing

1. Lift the handset or press

2. Dial the fax number.

3. Wait for the reception tone (if a person answers, ask them to press their Start key).

4. Press:

Rapid Key Dialing

Press the appropriate Rapid Key. Transmission will begin automatically. (Note for UX-8/GQ-5: Rapid Key Dialing is not available.)

Speed Dialing

1. Press:

2. Enter 2-digit Speed Dial number.

3. Press:

RECEIVING FAXES

Press the RESOLUTION/RECEPTION MODE key until the arrow in the display points to the desired reception mode (make sure the document feeder is empty).

SPEAKER

SPEED

DIAL

FAX mode: The f ax machine automatically answers on four rings and receives the incoming document.

TEL mode:

TEL/FAX mode: The fax machine automatically answers on 1 or 2 rings and re-

ceives faxes . V oice calls (including manually dialed f ax transmissions) are signalled by a special ringing sound.

A.M. mode: Select this mode when an answering machine is connected to the fax and the answering machine is turned on.

START

SETTING THE DATE AND TIME

1. Press: Display shows: DATE & TIME SET

2. Press:

3. Enter two digits for the Day (01 through 31).

4. Enter two digits for the Month (01 through 12).

5. Enter four digits for the Year (Ex: 1999).

6. Enter two digits for the Hour (01 through 23).

7. Enter two digits for the Minute (00 through 59).

8. When finished, press:

STORING AND CLEARING AUTO DIAL NUMBERS

1. Press:

Display shows: FAX/TEL # MODE

2. Press 1 to store a number or 2 to clear a number.

3. Enter a 2-digit Speed Dial number (from 01 to 05 for Rapid Key Dialing, or 06 to 40 for Speed Dialing) (If you are clearing a number, go to Step 7.) ( UX-8: 01 to

10)

4. Enter the full fax/telephone number.

5. Press:

6. Enter the name of the location by pressing number keys (Refer to the letter entry table in

ENTERING YOUR NAME AND NUMBER

7. Press:

A = B =

C =

D =

E =

F =

G =

H =

I =

J =

K =

L =

M =

N =

O =

P =

Q = R =

S =

T = U =

V =

W =

X =

Y =

Z =

SPACE =

• To change case, press the REDIAL key.

Press # or to scroll through symbols and special characters.

6. When finished, press:

START

STOP

FUNCTION

START

FUNCTION

START

STOP

START

STOP

Beep

START

RECEIVING

Page 12

1 – 10

UX-8TH/UX-40TH GQ-5TH/FO-50TH

M E M O

Page 13

UX-8TH/UX-40TH GQ-5TH/FO-50TH

CHAPTER 2. ADJUSTMENTS

[1] Adjustments

General

Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary.

1. Adjustments

Adjustments of output voltage (FACTORY ONLY)

1. Install the power supply unit in the machine.

2. Set the recording paper and document.

3. When the document is loaded, pow er is supplied to the output lines . Confirm that outputs are within the limits below.

Output voltage settings

3. Settings Dial mode selector

DIAL mode (Soft Switch No. SWB4 DATA No. 2)

1DG 2 +5V 3MG 4MG 5 +24V 6 +24V 7DG 8 PSAVE

2 – 1

TEL/LIU PWB

POWER SUPPLY PWB

CNL IUA

CNLIUA

CN2

CNPW

CONTROL PWB

(step 1) Select "OPTION SETTING".

KEY : FUNCTION 4

DISPLAY: OPTION SETTING PRESS OR #

(step 2) Select "DIAL MODE".

KEY: Push # until " DAIL MODE " is indicated because the number of # s changes by the model.

DISPLAY: DIAL MODE

(step 3) Select, using "1" or "2".

KEY: 1

DISPLAY: TONE SELECTED

KEY: 2

DISPLAY: PULSE SELECTED

(step 4) End, using the "STOP" key.

KEY:

Cursor When initially registering, the mode shows 1=TONE. When registering again, the mode which was registered formerly is shown.

STOP

1=TONE, 2=PULSE

Output Voltage limits

+5V 4.75V ∼ 5.25V

+24V 24.0V ∼ 26.0V

Connector

No. CNPW

Pin No.

2. IC protectors replacement

ICPs (IC Protectors) are installed to protect the motor driver circuit. ICPs protect various ICs and electronic circuits from an overcurrent condition.

The location of ICPs are shown below:

CNLIUA

CNPW

CONTROL PWB

(TOP SIDE)

CNMT

FU100

(1)FU100 (KAB2402) is installed in order to protect IC’s from an over-

current generated in the motor drive circuit. If FU100 is open, replace it with a new one.

Page 14

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[2] Diagnostics and service soft switch

1. Operating procedure (1) Entering the diagnostic mode

Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. ROM Ver. FZJ0 (FZK0 ) After 2 sec: DIAG MODE

FZJ0 (UX-8TH/GQ-5TH)

FZK0 (UX-40TH/FO-50TH)

Then press the START key and country name selected by country select will appear. Select the desired item with the key or the # key or select with the direct key. Enter the mode with the START key.

(Diag•specifications)

If the diag mode cannot be set, repeat the diag mode operation, performing the following operation. After the power is turned on and "WAIT A MOMENT" is indicated, press the STOP key.

In relation with the process response (request from Production Engineering) "WAIT A MOMENT" clock indication ma y appear depending on STOP key timing. If the ST OP ke y is held down, "MEMORY CLEAR?" appears.

FUNC

DIAG MODE

9 8 7

START —Soft switch mode START

AROM & RAM check

START

—Aging mode

START

—Panel check mode

START

BCheck pattern

START CSignal send mode

START

KEY

STOP

KEY

"Power ON"

Memory clear (Work + Backup)

FZJ0

All black mode

START START

Auto feeder mode

START

—

Entry data send

START

Entry data receive

Country select

START

Shading mode

START

—

START —Memory clear

FZK0

2 – 2

2. Diagnostic items

ITEM DIRECT

No. key

Contents Function

1 — SOFT SWITCH MODE Soft switches are displayed and changed. List can be output. 2 A ROM & RAM CHECK ROM is sum-checked, and RAM is matched. Result list is output. 3 — AGING MODE 10 sheets of check patterns are output every 5 minutes per sheet. 4 — PANEL CKECK MODE Panel keys are tested. Result list is output. 5 B CHECK PATTERN 2 sheets of check patterns are output. 6 C SIGNAL SEND MODE Various signals of FAX communication are output. 7 — MEMORY CLEAR Back-up memory is cleared, and is set at delivery. 8 — SHADING MODE Shading compensation is performed in this mode.

9 D ALL BLACK PRINT To check the print head, whole dots are printed over the interval of 2 m. 10 E AUTO FEEDER MODE Insertion and discharge of document are tested. 11 — ENTRY DATA SEND Registered content is sent. 12 — ENTRY DATA RECEIVE Registered content is received, and its list is output. 13 — COUNTRY SELECT The software parameter that it agreed in each country name is set up.

Page 15

UX-8TH/UX-40TH GQ-5TH/FO-50TH

3. Diagnostic items description

3. 1. Soft switch mode

The soft switches are provided so that each operation mode can be set by using the operation panel.

In this mode, these switches can be checked and set. The contents of these switches are backed up. The available soft switches are SW-A1 to SW-K1. The content of soft switches is shown in page 2-5 to 2-17. The contents are set to factory default settings.

3. 2. ROM & RAM check

ROM executes the sum check, and RAM executes the matching test. The result will be notified with the number of short sounds of the buzzer as well as by printing the ROM & RAM check list. Number of short sounds of buzzer 0 → No error

1 → ROM error 2 → RAM error (32Kbyte)

3. 3. Aging mode

If any document is first present, copying will be ex ecuted sheet by sheet. If no document is present, the check pattern will be printed sheet by sheet. This operation will be executed at a rate of one sheet per 5minutes, and will be ended at a total of 10 sheets.

3. 4. Panel check mode

This mode is used to check whether each key operates properly or not. Press the key on the operation panel, and the key will be displayed on the display . Therefore, press all k eys. At this time,finally press the STOP key.

When the STOP key is pressed, the keys which are not judged as "pressed" will be printed on the result list.

• LED part of the contact image sensor (CIS) is kept on during the term from when "ST AR T" of the panel test mode to end with the STOP k ey.

3. 5. Check pattern

This mode is used to check the status of print head. Two sheets of check pattern are printed. The f ollowing information of check pattern is printed.

Vertical stripes (alternate white and black lines) Approx. 35 mm

Full black Approx. 70 mm

Full white Approx. 35 mm

3. 6. Signal send mode

This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreov er , the signal sound is also output to the speaker when the line monitor of the soft switch is on.

[1] No signal (CML signal turned on) [2] 9600bps [3] 7200bps [4] 4800bps [5] 2400bps [6] 300bps (FLAG) [7] 2100Hz (CED) [8] 1100Hz (CNG) [9] Pseudo Ring (models with auto TEL/FAX changeover function) [10] END

3. 7. Memory clear

This mode is used to clear the backup memory and to reset to the factory default settings. The content of each setting will be cleared.

Note: Be sure to ex ecute the memory clear mode whenev er you change

the country select setting. The def ault settings of the soft s witches vary according to the destinations. Theref ore, if you do not e xecute the memory clear after changing the country select setting, some functions may not work.

3. 8. Shading mode

The mode is used for the shooting compensation. For reading, set up the special original paper.

The shooting compensation memorizes the reference data of white and black for reading.

Moreover, the memoriz ed data is not erased ev en if memory clear mode is executed.

3. 9. All black print

This mode is used to check the state of the printing head and intentionally overheat it. Whole dots are printed over the interval of 2 m. If it is overheated or the printing sheet is jammed, press STOP ke y for the end.

3. 10. Auto feeder mode

In this mode, a document is inserted and discharged to check the auto feed function.

After this mode is started, set a document, and the document feed will be automatically tested.

3. 11. Entry data send

This mode is used to send the registered data to the other machine and to make the other machine copy the registered content. Before sending in this mode, it is necessary to set the other machine at the entry data receive mode.

The contents to be sent are as follows (the machine prints each list after the transmission has completed):

1. Telephone list data

2. Sender (cover sheet) register data

3. Optional setting content

4. Soft switch content

5. Junk fax number list

6. Country setting content

2 – 3

RANK 0 or 1

Note: There is a selection RANK 0 or 1 depending on resistance value of the thermal head. RANK 0 or RANK 1 is printed at the tail of check pattern to identify.

Page 16

UX-8TH/UX-40TH GQ-5TH/FO-50TH

3. 12. Entry data receive

This mode is used to receive the registered data from the other machine and to make your machine register the received data. Before receiving in this mode, it is necessary to set the other machine at the entry data send mode.

After receiving is completed, the machine prints the following lists:

1. Telephone list data

2. Soft switch list

3. Junk fax number list

2 – 4

Press

FUNCTION

9 8 7 START START

Press FUNCTION key.

Press key.

Bit1 - 8 are set.

Soft SW-A2 - SW-K1 are set.

S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0 S F T SW-A1 = 1 0 0 0 0 0 0 0

S F T SW-A2 = 0 0 0 0 0 0 0 0 S F T SW-M2 = 0 0 0 0 0 0 0 0

Press key during setting.

To finish the settings halfway between SW-A1 and SW-K1, press the STOP key. In this case, the setting being done to the SW No. on display will be nullified while settings done to the preceding SW Nos. remain in effect.

The soft switch mode is terminated.

S F T SW-A1 = 0 0 0 0 0 0 0 0

START

DATA No. 1 2 3 4 5 6 7 8

When the COPY key is pressed, the contents of soft switches are printed.

3. 13. Country select

This mode is used to set line connecting parameters which correspond to each destination.

When the country select mode is selected, and then the START key is pressed, the destination (country name) currently set will be displayed.

By pressing the # or key, selectable destinations (country names) are displayed. When the destination (country name) you want to choose is displayed, press the START key. Each parameter will be stored in RAM.

Destinations (Country names) you can select are as follows:

COUNTRY NAME COUNTRY NAME HONG KONG (HK) TAIWAN (AU) INDIA (IN) THAILAND (TH) MALAYSIA (MY) GENERAL AREA (GRU) RUSSIAN (RA) GENERAL AREA (GRH) SINGAPORE (SG) AUSTRALIA (A) SOUTH AFRICA (ZA) CHINA (CN)

Note: Be sure to execute the memor y clear mode whenever you

change the country select setting. The default settings of the soft switches vary according to the destinations. Therefore, if you do not execute the memory clear after changing the country select setting, some functions may not work.

Do not set a country select setting which is different from that of the destination of the machine. Some functions will not work because the function and the PWB specifications are different.

4. How to make soft switch setting

To enter the soft switch mode, press the following key entries in sequence.

Page 17

UX-8TH/UX-40TH GQ-5TH/FO-50TH

1 Protect from echo No Yes 0 2 Forced 4800bps reception Yes No 0 3 Footer Print Yes No 0

4 Length limitation of copy/send/receive No limit Copy/Send:60cm 0

Receive:1.5m 5 CSI transmission Not transmitted Transmitted 0 6 DIS receive acknowledgement during G3 Twice NSF:Once 0

transmission DIS:Twice

7 Non modulated carrier for V29 transmission Yes No 0

mode

8 Reserved 0

Modem speed V.29 V.27 ter

9600bps 7200bps 4800bps 2400bps

1 No. 100000 2 No. 200000 3 No. 301100

4 No. 411001 5 Reserved 0

6 H2 mode No Yes 0 7 Communication error treatment in RTN No communication error Communication error 0

sending mode(Reception)

8 CNG transmission No Yes 0

CED tone signal interval 1000ms 750ms 500ms 75ms

1No. 111000 2No. 210100 3 MR Coding No Yes 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Signal Transmission level Binary input 0 2 (0~-31 dBm setting by 1dBm step) No. = 16 8 4 2 1 0 3 1 2 3 4 5 1 4 0 0 1 0 0 0 5 0 6 Protocol monitor(Error print) Printed at com. error Not printed 0

7 Protocol monitor Yes No 0 8 Line monitor Yes No 0

Digital equalization setting(Reception) 7.2km 0km

1No. 1101 2No. 2101

Digital equalization setting(Transmitter) 7.2km 0km

3No. 3100 4No. 4100

Digital equalization setting(Reception 7.2km 0km

5 for Caller ID) No. 5 1 0 0 6No. 6100

7 Error criterion 10 ~ 20 % 5 ~ 10 % 0 8 Anti junk fax check Yes No 1

5. Soft switch description

• Soft switch

SW NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 5

Remarks

Initial

setting

Page 18

UX-8TH/UX-40TH GQ-5TH/FO-50TH

1 Auto gain control(MODEM) Enable Disable 1 2 End Buzzer Yes No 1 3 Disconnect the line when DIS is received in No Yes 1

RX mode

4 Equalizer freeze control(MODEM) On Off 0 5 Equalizer freeze control 7200 bps only No Yes 0

6 CNG transmission in manual TX mode Yes No 1 7 Initial compression scheme for sharp fax in MR mode H2 mode 0

TX mode

8 Modem speed automatic down when RX Yes No 0

level is under -40dBm EOL detect timer 5 seconds 13 seconds 20 seconds25 seconds

1 No. 100110 2 No. 201011 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Hold key Enable Disable 1 2 Auto dial fax transmission by REDIAL key Yes No 0

3 Reserved 0 4 Recall interval Binary input 0

5 (0~15.5min setting by 0.5min step) No. = 16 8 4 2 1 1 6 4 5 6 7 8 0 7 0 1 0 1 0 1 8 0 1 Recall times(0~15times setting) Binary input 0 2 No. = 8 4 2 1 0

3 1 2 3 4 1 4 0 0 1 0 0 5 Dial tone detection(Before auto dial) No Yes 1 6 Reserved 0

7 Busy tone detection(After auto dial) No Yes 1 8 Busy tone detection pulse number 4 pulses 2 pulses 0

(After auto dial)

Waiting time after dialing

45 seconds 55 seconds 90 seconds 140 seconds

1 No. 100110 2 No. 201010 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Dial pausing(sec/pause) 4 sec 2 sec 0

2 Dial mode Tone Pulse 1 OPTION 3 Pulse → Tone change function by key Enable Disable 1

4 Dial pulse make/break ratio(%) 40/60 33/67 1

Auto dial mode Delay timer of before line

0 second 1.5 seconds 3.0 seconds 4.5 seconds

5 connect No. 5 0 0 1 1 1 6No. 601010 7 Reserved 0

8 Reserved 0

SW NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 6

Remarks

Initial

setting

Page 19

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Auto dial mode Delay timer of after line 1.7s 2.0s 2.5s 3.0s 3.6s 4.0s 5.5s 7.0s

1 connect No. 1 0 0 0 0 1 1 1 1 0 2 No. 2001100111 3 No. 3010101011 4

Fax signal detection after telephone mode dial

Yes No 0 5 Reserved 0 6 Reserved 0 7 Reserved 0

8 Reserved 0 1 DTMF signal transmission level Binary input 0

2 (Low frequency 0~15.5dBm setting No. = 16 8 4 2 1 1 3 by 0.5dBm step) 1 2 3 4 5 0

4 0 1 0 1 0 1 5 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 DTMF signal transmission level Binary input 0 2 (High frequency 0~15.5dBm setting No. = 16 8 4 2 1 0 3 by 0.5dBm step) 1 2 3 4 5 1

4 0 0 1 1 1 1 5 1

6 Reserved 0 7 Reserved 0

8 Reserved 0

Reading Slice(Binary) Factory Dark Light Daker in

setting dark

1 No. 100110 2 No. 201010

Reading Slice(Half tone) Factory Dark Light Daker in

setting dark

3 No. 300110 4 No. 401010 5 Line density selection Fine Standard 0 6 Reserved 0

7 MTF correction in half tone mode No Yes 0 8 Reserved 0

1 Number of rings for auto receive Binary input 0 OPTION 2 (0~15rings setting) No. = 8 4 2 1 0 3 1 2 3 4 1

4 0 0 1 0 0 5 Automatic swiching manual to auto receive Yes No 0

function CI detect frequency

As PTT 11.5Hz 13.0Hz 20.0Hz

6 No. 600110 7 No. 701010 8 Reserved 0

2 – 7

SW NO.

DA TA

NO.

ITEM

Switch setting and function

Remarks

Initial

setting

Page 20

UX-8TH/UX-40TH GQ-5TH/FO-50TH

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Caller ID function Yes No 0 7 Reserved 0 8 Reserved 0 1 CI off detection timer Binary input 0 2 (0~1550ms setting by 50ms step) No. = 16 8 4 2 1 1 3 1 2 3 4 5 1

4 0 1 1 1 0 1 5 0

6 Reserved 0 7 Reserved 0 8 Reserved 0 1 DTMF type Caller ID RX level Binary input 1 2 (0~-44dBm setting by 1dBm step) No. = 32 16 8 4 2 1 0 3 1 2 3 4 5 6 1

4 1 0 1 1 0 0 1 5 0

6 0 7 Reserved 0

8 Reserved 0

Pseudo ringing time at the TEL/FAX

9sec 15sec 30sec 60sec 90sec 120sec 150sec 180sec

1 automatic switching mode No. 1 0 0 0 0 1 1 1 1 0 2 No. 2001100111 3 No. 3010101010 4 Number of CNG signal detection at the Twice Once 1

TEL/FAX automatic switching mode

5 CNG detect time at TEL/FAX mode 3 sec 5 sec 0 6 Post answer tone(TEL/FAX mode) No Yes 1

7 Type of post answer tone LA-SI-DO tone 800Hz single tone 1 8 Pseudo ringer ON/OFF cycle 1 sec ON / 4 sec OFF 1 sec ON / 2 sec OFF 0

1 Pseudo ringer sound output level to the line Binary input 1 2 (0~-15dBm setting by 1dBm step) No. = 8 4 2 1 0 3 1 2 3 4 1

4 1 0 1 0 0 5 Post answer tone transmission level Binary input 0

6 (0~-15dBm setting by 1dBm step) No. = 8 4 2 1 1 7 5 6 7 8 0 8 0 1 0 0 0

Disconnect the line when DTMF "#" is received

Yes No 0

during TEL/FAX automatic switching mode

2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0

SW NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 8

Remarks

Initial

setting

Page 21

UX-8TH/UX-40TH GQ-5TH/FO-50TH

DTMF detection time 50ms 80ms 100ms 120ms 1 No. 100110 2 No. 201010

3 Protection of remote reception(5 )Yes No 0

detection 4 Remote reception with GE telephone Compatible Not compatible 1 5 Remote operation code figure by external Binary input 0 OPTION

6 TEL (0~9) No. = 8 4 2 1 1 7 5 6 7 8 0

8 0 1 0 1 1 1 CNG detection in STAND-BY mode Yes No 1 OPTION

Number of CNG detect(AM mode) 1 pulse 2 pulses 3 pulses 4 pulses 2 No. 200110 3 No. 301011

Number of CNG detect(STAND-BY mode) 1 pulse 2 pulses 3 pulses 4 pulses 4 No. 400110 5 No. 501011

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Quiet detect time Binary input 0 OPTION 2 (0~15sec setting by 1sec step) No. = 8 4 2 1 1 3 1 2 3 4 0

4 0 1 0 0 0 5 Quiet detect start timing Binary input 0 OPTION

6 (0~15sec setting by 1sec step) No. = 8 4 2 1 1 7 5 6 7 8 0

8 0 1 0 1 1 1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

OGM detect timer Not work 100ms 200ms 300ms 1 No. 100110 2 No. 201011

Section time of quiet detection 30s 40s 50s 60s 3 No. 300110 4 No. 401011

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Quiet detect level setting Binary input 1 2 (0~-44dBm setting by 1dBm step) No. = 32 16 8 4 2 1 0 3 1 2 3 4 5 6 1

4 1 0 1 1 0 0 1 5 0

6 0 7 Fax switching when A.M. full Yes No 0 OPTION

8 Reserved 0

SW NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 9

Remarks

Initial

setting

Page 22

UX-8TH/UX-40TH GQ-5TH/FO-50TH

1 Busy tone continuous sound detect time 5 sec 10 sec 1 2 Reserved 0 3 Busy tone detect continuation sound detect No Yes 0

4 Reserved 0 5 Busy tone detect intermittent sound detect No Yes 0

Busy tone detection pulse number 2 pulses 4 pulses 6 pulses 10 pulses 6 No. 600110 7 No. 701011

8 Reserved 0

Busy tone detection ON/OFF time(Lower limit)

150 ms 200 ms 250 ms 350 ms 1 No. 100110 2 No. 201010

Busy tone detection ON/OFF time(Upper limit)

650 ms 900 ms 1500 ms 2700 ms 3 No. 300110 4 No. 401011

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0 2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0 1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 10

Remarks

Initial

setting

Page 23

UX-8TH/UX-40TH GQ-5TH/FO-50TH

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0

5 Reserved 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Sender’s phone number setting Cannot change Change allowed 0 2 Reserved 0

Ringer volume Off Low Middle High OPTION

3 No. 300111 4 No. 401010

Speaker volume Low Low Middle High OPTION

5 No. 500111 6 No. 601010

7 Polling key (UX-40/FO-50 only) Yes No 0 OPTION 8 Reserved 0

1 Reserved 0 2 Reserved 0

3 Reserved 0 4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Saving energy start timing 5 sec 180 sec 0 8 Saving energy mode Enable Disable 1

SW NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 11

Remarks

Initial

setting

Page 24

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Communication results printout Error Send only Always No print OPTION

(Transaction report)

No. 100000 2 No. 200110 3 No. 301010 4 Time format 12 hour 24 hour 0

5 Date format Month-Day-Year Day-Month-Year 0 6 Reserved 0

7 Reserved 0 8 Reserved 0

1 Entering diag mode by pressing SPEED key Yes No 0 2 Reserved 0 3 Reserved 0

4 Reserved 0 5 Reserved 0

6 Reserved 0 7 Reserved 0

8 Reserved 0

NO.

DA TA

NO.

ITEM

Switch setting and function

2 – 12

Remarks

Initial

setting

Page 25

UX-8TH/UX-40TH GQ-5TH/FO-50TH

• Soft switch function description

SW-A1 No. 1 Protect from echo

Used to protect from echo in reception.

SW-A1 No. 2 Forced 4800BPS reception

When line conditions warrant that receptions take place at 4800 BPS repeatedly. It may improve the success of receptions by setting at 4800BPS. This improves the receiving document quality and reduces handshake time due to fallback during training.

SW-A1 No. 3 Footer print

When set to "1", the date of reception, the sender machine No., and the page No. are automatically recorded at the end of reception.

SW-A1 No. 4 Length limitation of copy/send/receive

Used to set the maximum page length. To avoid possible paper jam, the page length is normally limited to 0.6 meter for copy or transmit, and 1.5 meters for receive. It is possible to set it to "No limit" to transmit a long document, such as a computer print form, etc. (In this case, the receiver must also be set to no limit.)

SW-A1 No. 5 CSI transmission

(CSI TRANSMISSION) is a switch to set whether the machine sends or does not send the signal (CSI signal) informing its own telephone No. to the remote fax machine when information is received. When "nonsending" is set, the telephone No. is not output on the remote transmitting machine if the remote transmitting machine has the function to display or print the telephone No. of receiving machine, using this CSI signal.

SW-A1 No. 6 DIS receive ac knowledgment during G3 transmission

Used to make a choice of whether reception of DIS(NSF) is acknowledged after receiving two DISs(NSFs) or receiving one DIS (two NSFs). It may be useful for ov erseas communication to a v oid an echo suppression problem, if set to 1.

SW-A1 No. 7 Non modulated carrier for V29 transmission mode

Though transmission of a nonmodulated carrier is not required for transmission by the V29 modem according to the CCITT Recommendation, it may be permitted to a send nonmodulated carrier before the image signal to avoid an echo suppression problem. It may be useful for ov erseas communication to a v oid an echo suppression problem, if set to 1.

SW-A1 No. 8 Reserved

Set to "0".

SW-A2 No. 1 ~ No. 4 Modem speed

Used to set the initial modem speed. The default is 9600BPS. It may be necessary to program it to a slower speed when frequent line fallback is encountered, in order to save the time required for fallback procedure.

SW-A2 No. 5 Reserved

Set to "0".

SW-A2 No. 6 H2 mode

Used to determine reception of H2 mode (15 sec transmission mode). When set to OFF, H2 mode reception is inhibited even though the transmitting machine has H2 mode function.

SW-A2 No. 7 Comm unication error treatment in R TN sending mode (Reception)

Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to "1", communication error is judged as no error.

SW-A2 No. 8 CNG transmission

When set to "0", this model allows CNG transmission by pressing the Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case, CNG transmission can be performed in the auto dial mode.

SW-A3 No. 1, No. 2 CED tone signal interval

For international communication, the 2100Hz CED tone may act as an echo suppression switch, causing a communication problem. Though SW-A3 No. 1 and No . 2 are normally set to 0, this selfing is used to change the time between the CED tone signal to eliminate the communication caused by echo.

2 – 13

TX RX

CED

DIS

SW-A3 No. 3 MR coding

Used to select the MR coding enable or disable.

SW-A3 No. 4 ~ No. 8 Reserved

Set to "0".

SW-A4 No. 1 ~ No. 5 Signal transmission level (0~-31 dBm setting by 1dBm step)

Used to control the signal transmission level in the range of -0dB to

-31dB. The factory setting is at -10dB (MODEM output).

SW-A4 No. 6 Protocol monitor (Error Print)

If set to "1", protocol is printed at communication error.

SW-A4 No. 7 Protocol monitor

Normally set to "0". If set to "1", communication can be check ed, in case of trouble, without using a G3 tester or other tools. When communication FSK data transmission or reception is made, the data is taken into the buffer . When communication is finished, the data is analyzed and printed out. When data is received with the line monitor (SW4-No. 8) set to "1" the reception level is also printed out.

SW-A4 No. 8 Line monitor

Normally set to "0". If set to "1", the transmission speed and the reception level are displayed on the LCD. Used for line tests.

SW-A5 No. 1, No. 2 Digital equalization setting (Reception)

Line equalization when reception is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 3, No. 4 Digital equalization setting (Transmitter)

Line equalization when transmission is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

Page 26

UX-8TH/UX-40TH GQ-5TH/FO-50TH

SW-A5 No. 5, No. 6 Digital equalization setting (Reception for Caller ID)

Line equalization when reception for CALLER ID is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station.

SW-A5 No. 7 Error criterion

Used to select error criterion for sending back RTN when receiving image data.

SW-A5 No. 8 Anti junk fax check

When using the Anti junk fax function, set to "1".

SW-A6 No. 1 Auto gain control(MODEM)

When this mode is enabled, if the reception signal level is under 31dBm, the modem itself controls the signal gain automatically.

SW-A6 No. 2 End buzzer

Setting this bit to 0 will disable the end buzzer (including the error buzz er/ on-hook buzzer).

SW-A6 No. 3 Disconnect the line when DIS is received in RX mode

Bit1 = 0 : When DIS signal is receiv ed during RX mode, disconnect the

line immediately.

Bit1 = 1 : When DIS signal is receiv ed during RX mode, wait f or the ne xt

signal.

SW-A6 No. 4 Equalizer freeze control (MODEM)

This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in unfavorable state and picture cannot be received. * Usually , the control is ex ecuted according to the state of line where the equalizer setting is changed always.

SW-A6 No.5 Equalizer freeze 7200BPS only

Setting which specifies SW-A6 No. 4 control only in condition of 7200BPS modem speed.

SW-A6 No. 6 CNG transmission in manual TX mode

When set to "1", fax transmit the CNG signal in case of manual transmissiom mode (User press the START key after waiting for the f ax answering signal from handset or speaker).

SW-A6 No. 7 Initial compression scheme for sharp fax in TX mode

When set to "0", if the other fax is Sharp model, fax transmit the document by H2 mode. When set to "1", even if the other fax is Shar p model, fax transmit the document by MR mode.

SW-A6 No. 8 Modem speed automatic do wn when RX level is under

-40dBm

When set to "1", if fax signal level is under -40dBm during reception, machine selects the slower modem speed automatically. It is effective when noises occur on the received document due to the long distance communications.

SW-A7 No. 1, No. 2 EOL (End Of Line) detect timer

Used to make a choice of whether to use the 5 or 13 or 20 or 25 seconds timer for detection of EOL. This is effective to ov erride communication failures with some facsimile models that have longer EOL detection.

SW-A7 No. 3 ~ No. 8 Reserved

Set to "0".

SW-B1 No. 1 Hold key

Used to set YES/NO of holding function by the HOLD key.

SW-B1 No. 2 Auto dial fax transmission by REDIAL key

When set to "1", if original documents are set to the feeder and you press REDIAL key, machine will dial and transmit the ducuments automatically. When set to "0", operator needs to press the START key after FAX reception tone is heard.

SW-B1 No. 3 Reserved

Set to "0".

SW-B1 No. 4 ~ No. 8 Recall interval (0~15.5min setting by 0.5min step)

Choice is made for a redial interval for speed and rapid dial calls. Use a binary number to program this with 0.5min steps. If set to 0 accidentally, 0.5min will be assumed.

SW-B2 No. 1 ~ No.4 Recall times (0~15times setting)

Choice is made as to how many redials there should be.

SW-B2 No. 5 Dial tone detection (Before auto dial)

Used to set YES/NO of dial tone detection in auto dialing.

SW-B2 No. 6 Reserved

Set to "0".

SW-B2 No. 7 Busy tone detection (After auto dial)

Used to set YES/NO of busy tone detection after auto dialing.

SW-B2 No. 8 Busy tone detection pulse number (After auto dial)

Used for detection of busy tone in 2 or 4 pulses.

SW-B3 No. 1, No. 2 Waiting time after dialing

This is waiting time for the opponent's signals after dialing. 45 / 55 / 90 / 140 seconds settings are available.

SW-B3 No. 3 ~ No. 8 Reserved

Set to "0".

SW-B4 No. 1 Dialing pause (sec/pause)

Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available.

SW-B4 No. 2 Dial mode

When using the pulse dial, set to 0. When using the tone dial, set to 1.

SW-B4 No. 3 Pulse → Tone change function by key

When setting to 1, the mode is changed by pressing the key from the pulse dial mode to the tone dial mode.

SW-B4 No. 4 Dial pulse make/break ratio (%)

When using the 33% make ratio pulse dial, set to 0. When using the 40% make ratio pulse dial, set to 1.

SW-B4 No. 5, No. 6 Auto dial mode Delay timer of before line connect

Delay time between the dial key input and line connection under the auto dial mode.

2 – 14

RAPID A CML RELAY ON

DIALLING

No.5=0 No.6=0 : 0sec No.5=0 No.6=1 : 1.5sec No.5=1 No.6=0 : 3.0sec No.5=1 No.6=1 : 4.5sec

SW-B4 No. 7, No. 8 Reserved

Set to "0".

Page 27

UX-8TH/UX-40TH GQ-5TH/FO-50TH

2 – 15

No. 1 No. 2 No. 3

0 0 0 1.7sec 0 0 1 2.0sec 0 1 0 2.5sec 0 1 1 3.0sec 1 0 0 3.6sec 1 0 1 4.0sec 1 1 0 5.5sec 1 1 1 7.0sec

SW-B5 No. 1 ~ No. 3 Auto dial mode Delay timer of after line connect

Delay time between the line connection and dial data output under the auto dial mode. This setting is available when dial tone detection(SW -B2 No. 5) is set to "NO".

SW-C1 No. 5 Line density selection

Used to set the transmission mode which is automatically selected when the Resolution key is not pressed. In the copy mode, however, the fine mode is automatically selected unless the Resolution key is manually set to another mode.

SW-C1 No. 6 Reserved

Set to "0".

SW-C1 No. 7 MTF correction in half tone mode

This allows selection of MTF correction (dimness correction) in the half tone mode. When "NO" (=1) is selected, the whole image becomes soft and mild. Clearness of characters will be reduced. Normally set to "YES" (=0).

SW-C1 No. 8 Reserved

Set to "0".

SW-D1 No.1 ~ No. 4 Number of rings for auto receive (0~15rings setting)

When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to nine rings using a binary number. Since the facsimile telephone could be used as an ordinary telephone if the handset is taken off the hook, it should be programmed to the user's choice. If the soft switch was set to 1, direct connection is made to the facsimile. If a facsimile calling beep was heard when the handset is taken off the hook, press the ST AR T ke y and put the handset on the hook to have the facsimile start receiving. If it was set to 0 accidentally, receive ring is set to 1.

NOTE: If the machine is set to answer after a large number of rings, it

may not be able to receive faxes successfully. If you have difficulty receiving f axes , reduce the number of rings to a maximum of 5.

SW-D1 No. 5 Automatic switching manual to auto receive function

This soft switch is used to select whether the machine should switch to the auto receive mode after 5 rings in the manual receive mode or remain in the same way as SW -D1 No. 1, No. 2, No . 3 and No. 4 "0"1"0"1"(5 rings).

SW-D1 No. 6, No. 7 CI detect frequency

Detection frequency of ring signal for auto reception is set. When set to No. 6=0, No. 7=0,frequency is set to PTT recommendation.

When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more. When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more. When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.

SW-D1 No. 8 Reserved

Set to "0".

SW-D2 No. 1 ~ No. 5 Reserved

Set to "0".

SW-D2 No. 6 Caller ID Function

Used for Caller ID function.

SW-D2 No. 7, No. 8 Reserved

Set to "0".

RAPID A CML RELAY ON

DIAL DATA

SW-B5 No. 4 Fax signal detection after telephone mode dial

When set to "1", if machine detects the fax answering signal after telephone calling (handset off-hook or speaker mode dial), machine starts to receive the documents automatically.

SW-B5 No. 5 ~ No. 8 Reserved

Set to "0".

SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (Low frequency 0~15.5dBm setting by 0.5dBm step)

The transmission level of DTMF signal is adjusted. (lower frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)

SW-B6 No. 6 ~ No. 8 Reserved

Set to "0".

SW-B7 No. 1 ~ No. 5 DTMF signal transmission level (High frequency 0~15.5dBm setting by 0.5dBm step)

The transmission level of DTMF signal is adjusted. (higher frequency)

00000: 0dBm

↓

11111: -15.5 dBm (-0.5dBm x 31)

SW-B7 No. 6 ~ No. 8 Reserved

Set to "0".

SW-C1 No. 1, No. 2 Reading slice (Binary)

Used to determine the set value of reading density in standard/fine/super-fine mode. The standard setting is "00"(Factory setting is "00").

SW-C1 No. 3, No. 4 Reading slice (Half tone)

Used to determine the set value of reading density in half tone mode. The standard setting is "00"(Factory setting is "00").

Page 28

UX-8TH/UX-40TH GQ-5TH/FO-50TH

2 – 16

SW-E3 No. 1 Disconnect the line when DTMF "#" is received during TEL/FAX automatic switching mode

When set to "1", if machine detects the DTMF code # during phone/fax automatic switching mode, stop the pseudo ringer and disconnect the line. This effect when operator want to stop the pseudo ringer from extension phone connected with parallel.

SW-E3 No. 2 ~ No. 8 Reserved

Set to "0".

SW-F1 No. 1, No. 2 DTMF detection time

Used to set detect time of DTMF (Dual Tone Multi Frequency) used in remote reception(5 ). The longer the detect time is, the less the error detection is caused by noises.

SW-F1 No. 3 Protection of remote reception (5 ) detection

Used to set the function of remote reception (5 ). When set to "1", the remote reception function is disabled.

SW-F1 No. 4 Remote reception with GE telephone

"1": Compatible with TEL mode by GE "0": Not compatible

• When sending (5 ) for remote reception with a GE manufactured telephone remote reception may not take place because of special specifications in their DTMF.

To overcome this, a soft SW is provided to change the modem setting

to allow for remote reception.

• If this soft SW is set to "1", other telephone sets may be adversely affected.

SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0~9)

Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex- 7 (Default : 5 )

SW-F2 No. 1 CNG detection in STAND-BY mode

When setting to "1", the CNG signal detection function during standby stops.

SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode)

Used for detection of CNG in 1 to 4 pulses.

SW-F2 No. 6 ~ No. 8 Reserved

Set to "0".

SW-G1 No. 1 ~ No. 4 Quiet detect time (0~15sec setting by 1sec step)

When an answering machine is connected, if a no sound state is detected for a certain period of time, the machine judges it as a transmission from a facsimile machine and automatically switches to the FAX mode.

SW-G1 No. 5 ~ No. 8 Quiet detect start timing (0~15sec setting by 1sec step)

Inserts a pause before commencing quiet detection.

SW-G2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-G3 No. 1, No. 2 OGM detect timer

This is used to change the OGM detection time for answering machine hook up detection.

SW-G3 No. 3, No. 4 Section time of quiet detection

The switch which sets the time from the start of detection function to the end of the function.

SW-G3 No. 5 ~ No. 8 Reserved

Set to "0".

SW-D3 No. 1 ~ No. 5 CI off detection timer (0~1550ms setting by 50ms step)

Set the minimum time period of CI signal interruption which affords to be judged as a CI OFF section with 50ms steps. (Example)

400msec

2000msec

0 1 1 1 0 (50ms~14) : 700ms(CI interruption>700ms:Judged as a CI

OFF section) The section 1 is not judged as a CI OFF section, the CI signal A is counted as one signal. The section 2 is judged as a CI OFF section, the CI signal B is considered as the second signal.

0 0 1 1 1 (50ms~7) : 350ms(CI interruption>350ms:J udged as a CI

OFF section) The section 1 is judged as a CI OFF section, and the CI signal A is counted as two signals. The section 2 is judged as a CI OFF section, and the CI signal B is considered as the third signal.

SW-D3 No. 6 ~ No. 8 Reserved

Set to "0".

SW-D4 No. 1 ~ No. 6 DTMF type Caller ID RX level (0~-44dBm setting by 1dBm step)

This is used for DTMF type Caller ID detection level setting.

SW-D4 No. 7, No. 8 Reserved

Set to "0".

SW-E1 No. 1 ~ No. 3 Pseudo ringing time at the TEL/F AX automatic switching mode

Choice is made as to how long to rumble the dummy ringer on TEL/FAX automatic switching mode.

SW-E1 No. 4 Number of CNG signal detection at the TEL/F AX automatic switching mode

Used for detection of CNG in one tone or two tones in the TEL/FAX automatic switching mode.

SW-E1 No. 5 CNG detect time at TEL/FAX mode

The switch which sets the time from the start of CNG detection to the end of detection.

SW-E1 No. 6 Post answer tone (TEL/FAX mode)

When set to "0", machine send the tones in TEL/FAX auto changeover mode.

SW-E1 No. 7 Type of post answer tone

When set to "0", post answer tone is 800Hz single tone. When set to "1", post answer tone is 880Hz/988Hz/1046Hz(LA-SI-DO) tone.

SW-E1 No. 8 Pseudo ringer ON/OFF cycle

When set to "0", pseudo ringer is 1 sec ON and 2 sec OFF cycles. When set to "1", pseudo ringer is 1 sec ON and 4 sec OFF cycles.

SW-E2 No. 1 ~ No. 4 Pseudo ringer sound output level to the line (0~-15dBm setting by 1dBm step)

Used to adjust the sound volume of pseudo ringer to the line (ring back tone) generated on selecting TEL/FAX.

SW-E2 No. 5 ~ No. 6 Post answer tone transmission level (0~-15dBm setting by 1dBm step)

Used to adjust the sound volume of post answer tone to the line generated on selecting TEL/FAX.

Page 29

UX-8TH/UX-40TH GQ-5TH/FO-50TH

2 – 17

SW-G4 No. 1 ~ No. 6 Quiet detect level setting (0~-44dBm setting by 1dBm step)

This is used to change the quiet detect level setting. If quiet detection is difficult due to noise, reduce this setting level. (Example) Factory setting : 1 0 1 1 0 0 (- 44dBm)

↓ 1 0 1 0 0 0 (- 40dBm)

SW-G4 No. 7 Fax switching when A.M. full

If the answering machine’s memory (tape) is full and there is no response, the machine automatically switches to Fax reception.

SW-G4 No. 8 Reserved

Set to "0".

SW-H1 No. 1 Busy tone continuous sound detect time

Set detecting time busy tone continuous sound for 5 seconds or 10 seconds.

SW-H1 No. 2 Reserved

Set to "0".

SW-H1 No. 3 Busy tone detect continuation sound detect

Used to select detection of the continuous sound of certain frequency.

SW-H1 No. 4 Reserved

Set to "0".

SW-H1 No. 5 Busy tone detect intermittent sound detect

Used to select detection of the intermittent sound of certain frequency.

SW-H1 No. 6, No. 7 Busy tone detection pulse number

Used to set detection of Busy tone intermittent sounds.

SW-H1 No. 8 Reserved

Set to "0".

SW-H2 No. 1, No. 2 Busy tone detection ON/OFF time (Lower limit)

The initial value of detection is set according to electric condition. The set value is changed according to the local switch board. (Errone-

ous detection of sound is reduced.) If erroneous detection is caused by sound, etc., adjust the detection

range. The lower limit can be set in the range of 150msec to 350msec.

SW-H2 No. 3, No. 4 Busy tone detection ON/OFF time (Upper limit)

Similarly to SW-H2 No. 1, No. 2, the set value can be varied. The upper limit can be set in the range of 650msec to 2700msec.

SW-H2 No. 5 ~ No. 8 Reserved

Set to "0".

SW-I1 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I2 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I3 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I4 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I5 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I6 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I7 No. 1 ~ No. 8 Reserved

Set to "0".

SW-I8 No. 1 ~ No. 8 Reserved

Set to "0".

SW-J1 No. 1 Sender's phone number setting

Used to make a choice of whether the registered sender's phone number can be changed or not. If the s witch is set to "1", new registration of the sender's phone number is disabled to prevent accidental wrong input.

SW-J1 No. 2 Reserved

Set to "0".

SW-J1 No. 3, No. 4 Ringer Volume

Used to adjust ringing volume.

SW-J1 No. 5, No. 6 Speaker Volume

Used to adjust sound volume from a speaker.

SW-J1 No. 7 Polling key (UX-40/FO-50 only)

If this switch is set to 1, the last of Rapid key works as polling key.

SW-J1 No. 8 Reserved

Set to "0".

SW-J2 No. 1 ~ No. 6 Reserved

Set to "0".

SW-J2 No. 7 Saving energy start timing

Used to set the time between the machine’s stand-b y state (clock indication) after operation and saving energy mode. It is possible to set the time to either 5 sec or 180 sec (default).

SW-J2 No. 8 Saving energy mode

Used to select whether to make the saving energy mode valid or not.

SW-J3 No. 1 ~ No. 3 Communication results printout (T ransaction report)

It is possible to obtain transaction results after each communication. Normally,the switch is set (No. 1 : 0, No. 2 : 0, No. 3 : 0) so that the transaction report is produced only when a communication error is encountered. If No.1 was set to 0 and No. 2 to 1 and No. 3 to 0, the tr ansaction report will be produced every time a communicaion is done, even if the communicaion was successful. Setting No. 1 to 0 and No . 2 to 1 and No. 3 to 1 will disable this function. No transaction report printed.

SW-J3 No. 4 Time format

When set to "0", 24hour time format is used. When set to "1", 12hour time format is used.

SW-J3 No. 5 Date format

When set to "0", Day-Month-Year format is used. When set to "1", Month-Day-Year format is used.

SW-J3 No. 6 ~ No. 8 Reserved

Set to "0".

SW-K1 No. 1 Entering diag mode by pressing SPEED key

A bit which is used in the production process only . When the SPEED k ey is pressed, the switch is changed from the stand-by state to the diag mode.

SW-K1 No. 2 ~ No. 8 Reserved

Set to "0".

Page 30

UX-8TH/UX-40TH GQ-5TH/FO-50TH

2 – 18

[3] T roubleshooting

Refer to the following actions to troub leshoot an y of the problems mentioned in 1-4.

[1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK.

• Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.

May be used in case [1] [2] [3].

• Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,

5. May be used in case [3].

• Apply line equalization SOFT SWITCH A5-1, 2.

May be used in case [1] [2] [3] [4].

• Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,

4. May be used in case [2] [3].

• Replace the TEL/LIU PWB.

May be used in all cases.

• Replace the control PWB.

May be used in all cases.

* If transmission problems still exist on the machine, use the following

format and check the related matters.

TO: ATT: Ref.No.: CC: ATT: Date : FM: Dept :

Sign :

* Please complete this report before calling the “TAC” hotline if problem still occurs.

***** Facsimile communication problem *****

Ref.No.: Date:

From: Mr. Fax Tel No.: Our customer Name Tel No.

Address Fax No. Contact person Model name

Other party Name Tel No.

Address Fax No. Contact person Model name

Problem mode Line: Domestic / international Model: G3 Phase: A, B, C, D.

Reception / Transmission

Automatic reception / Manual reception

Automatic dialing / Manual dialing / Others Frequency: % ROM version: Confirmation

item

Please mark problem with an X. No problem is: 0.

A1 A2 B1 B2 C1 C2 D1 D2 E1 E2

Transmission level setting is ( ) dB at our customer Transmission level ( ) dBm Reception level ( ) dBm By level meter at B1 and B2

Comment

**** Please attach the G3 data and activity report on problem. ****

Countermeasure

Our customer

Our service

A1 A2

C1 D2

B1 B2

E1 E2

C2 D1

Other party

Other part

's service

Page 31

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[4] Error code table

1. Communication error code table G3 Transmission

Code Final received signal Error Condition (Receiver side)

0 Incomplete signal frame Cannot recognize bit stream after flag

1 NSF, DIS Cannot recognize DCS signal by echo etc.

Cannot recognize NSS signal (FIF code etc)

2 CFR Disconnects line during reception (carrier missing etc) 3 FTT Disconnects line by fall back

4 MCF Disconnects line during reception of multi page

Cannot recognize NSS, DCS signal in the case of mode change

5 PIP or PIN The line is hung up without replying to telephone request from the receiving party.

6 RTN or RTP Cannot recognize NSS, DCS signal after transmit RTN or RTP signal. 7 No signal or DCN No response in receiver side or DCN signal received* (transmitter side)

8 − Owing to error in some page the error could not be corrected although the specified number of

error retransmissions were attempted.

11 − Error occurred after or while reception by the remote (receiving) machine was revealed to be

impossible. 12 − Error occurred just after fallback. 13 − Error occurred after a response to retransmission end command was received.

G3 Reception

Code Final received signal Error Condition (Receiver side)

0 Incomplete signal frame Cannot recognize bit stream after flag

1 NSS, DCS Cannot recognize CFR or FTT signal

Disconnects line during transmission (line error)

2 NSC, DTC Cannot recognize NSS signal (FIF code etc) 3 EOP Cannot recognize MCF, PIP, PIN, RTN, RTP signal 4 EOM Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change

5 MPS The line is hung up without replying to communication request. 6 PR1-Q Cannot recognize PIP, PIN signal in the case of TALK request

7 No signal or DCN No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side) 8 − Error occurred upon completion of reception of all pages.

9 − Error occurred when mode was changed or Transmission/Reception switching was performed.

10 − Error occurred during partial page or physical page reception. 11 − Error occurred after or during inquiry from the remote (transmitting) machine as to whether

reception is possible or not. 12 − Error occurred during or just after fallback.

13 − Error occurred after the retransmission end command was received.

2 – 19

Page 32

UX-8TH/UX-40TH GQ-5TH/FO-50TH

CHAPTER 3. MECHANISM BLOCKS

[1] General description

1. Document feed block and diagram

Fig. 1

2. Document feed operation

1) The original, which is set in the document hopper, feeds automatically when the front sensor is activated. This in turn activates the pulse motor which drives the document supply roller. The document stops when the lead edge is detected by the document sensor.

2) The lead edge of the original is fed a specified number of pulses after the lead edge of the document is detected for the reading process to begin.

3) The trailing edge of the original is fed a specific number of pulses after the trailing edge of the document deactivates the document sensor. The read process then stops and the original is discharged.

4) When the front sensor is in the OFF state (any document is not set up in the hopper guide), the drive will be stopped when the document is discharged.

3. Hopper mechanism

3-1. General view

3-2. Automatic document feed

1) Use of the paper feed roller and separation rubber plate ensures error-free transport and separation of documents. The plate spring presses the document to the paper feed roller to assure smooth feeding of the document.

2) Document separation method: Separation rubber plate

Fig. 3

3-3. Documents applicable for automatic feed

NOTE: Double-side coated documents and documents on facsimile re-

cording paper should be inserted manually. The document feed quantity may be changed according to the document thickness.

Documents corresponding to a paper weight heavier than 69.2kg (80g/ m2 ) and lighter than 135kg (157g/m2 ) are acceptable for manual feed.

Documents heavier than 135kg in terms of the paper weight must be duplicated on a copier to make it operative in the facsimile.

3-4. Loading the documents

1) Make sure that the documents are of suitable size and thickness, and free from creases, folds, curls, wet glue, wet ink, clips, staples and pins.

2) Place documents face down in the hopper. i) Adjust the document guides to the document size. ii) Align the top edge of documents and gently place them into the

hopper. The first page under the stack will be tak en up by the f eed roller to get ready for transmission.

NOTES: 1) Curled edge of documents, if any, must be straightened

out.

2) Do not load the documents of different sizes and/or thicknesses together.

3 – 1

Operation panel PWB

Back roller

Document sensor

Separator plate(*)

Separator rubber(*)

Hopper guide

Document

Front sensor(*)

Paper feed roller(*)

CIS unit

(*): UX-40/FO-50 ONLY

Fig. 2

The hopper section contains document guides that are used to adjust the hopper to the width of the original document. This ensures that the original feeds straight into the fax machine for scanning. Document width: 148 mm to 216 mm (A5 longitudinal size to Letter

longitudinal size)

NOTE: Adjust the document guide after setting up the document.

Separation rubber (UX-40/FO-50 ONLY)

Feed plate

Document

Paper feed roller (UX-40/FO-50 ONLY)

Paper size 148mm x 140mm ~

A4 (210mm x 297mm), Letter (216mm x 279mm)

4x6 series (788mm x 1091mm x 1000mm sheets)

Square meter series

Minimum Maximum Minimum Maximum

Feeder capacity 5 sheets, max.

Paper thickness (ref.)

0.06mm 0.09mm 0.06mm 0.09mm

Paper weight 45kg 69.2kg 52g/m

80g/m

Page 33

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 4

3-5. Documents requiring use of document carrier

1) Documents smaller than 148mm x 140mm.

2) Documents thinner than the thickness of 0.06mm.

3) Documents containing creases, folds, or curls, especially those whose surface is curled (maximum allowable curl is 5mm).

4) Documents containing tears.

5) Carbon-backed documents. (Insert a white sheet of paper between the carbon back and the document carrier to avoid transfer of carbon to the carrier.)

6) Documents containing an easily separable writing material (e.g., those written with a lead pencil).

7) Transparent documents.

8) Folded or glued documents.

Document in document carrier should be inserted manually into the

feeder.

4. Document release

4-1. General

To correct a jammed document or to clean the document running surface, pull the insertion side of document center of the operation panel. T o open the upper document guide, the operation panel must be opened first.

4-2. Cross section view

5. Recording block 5-1. General view

3 – 2

Separation rubber (UX-40/FO-50 ONLY)

Paper feed roller (UX-40/FO-50 ONLY)

First page of document

Feed plate

Back of document

Last page of document

Fig. 5

Fig. 6

5-2. Driving

Via the pulse motor gear shaft, the reduction gear, and the recording paper feed gear, rotation of the pulse motor is con ve yed to the recording paper feed roller to feed the recording paper.

5-3. Recording

Use of a thermal head permits easier maintenance and low operating costs.

1) Thermal head

The thermal head consists of 1728-dot heat elements arranged in a single row and has the resolution of 8 dots/mm. The maximum recording speed is 10ms/line. The thermal head also incorporates a 1728-dot shift register latch and output control driver circuit. Low po wer consumption is achieved by dividing the head into nine segments.

2) Structure of the recording mechanism

Recording is accomplished by pressing the thermal head on the recording paper against the platen roller.

The main scan (horizontal) is electronically achieved, while the subscan (vertical) is achieved by moving the recording paper by the recording platen roller.

Usually, the cause for uneven print tone is caused by misalignment of the thermal head or uneven contact with the roller.

It can by checked in the following manner.

1) Check if the thermal head power and signal cables are properly routed.

2) Check that the thermal head pivot moves smoothly up and down.

3) Check that the thermal head support bracket is secured without any play.

4) Check to see that the recording platen roller has proper concentricity, in the case of a print tone variation evenly repeated down the page.

5) Replace the thermal head with a new one and check to see if the same trouble occurs.

Operation panel unit

Scanner frame unit

CIS release lever

Lower cabinet

PWB case unit

Recording paper

Scanner frame

Platen roller

PO guide

Thermal head

Head guide

Paper guide

Page 34

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[2] Disassembly and assembly procedures

• This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures.

• Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units,

refer to the Parts List.

• The numbers in the illustration, the parts list and the flowchart in a same section are common to each other.

• To assure reliability of the product, the disassembly and the assembly procedures should be performed carefully and deliberately.

Paper support guide, handset cover and scanner unit

Parts list (Fig. 1)

Fig. 1

No. Part name Q’ty No. Part name Q’ty

1 Mechanism unit 1 2 Screw (3×12) 2 3 Paper support guide 1 4 Paper sensor lever 1 5

Paper sensor lever spring

6 Panel stopper 1

3 – 3

7 Screw (3×8) 1 8 Handset cover 1

9 Hook switch lever 1 10 Screw (3×12) 2 11 Connector 2 12 Scanner unit 1

Hook

Control PWB

Hook

2 3 4 5

7 8 9

Fix position of spring

UX-40/

FO-50

ONLY

UX-40/

FO-50 ONLY

UX-40/

FO-50 ONLY

Page 35

UX-8TH/UX-40TH GQ-5TH/FO-50TH

11 Feed roller 1

(UX-40/FO-50 only) 12 Connector 1 13 CIS support, left 1 14 CIS support, right 1 15 CIS unit 1 16 CIS protect sheet 1 17 CIS spring 2 18 Connector 1

(UX-40/FO-50 only) 19 Front sensor 1

(UX-40/FO-50 only) 20 Scanner frame 1

Fig. 2

Parts list (Fig. 2)

No. Part name Q’ty No. Part name Q’ty

1 Document guide lower 1 2 Back roller gear 1 3 Back roller bearing, left 1 4 CIS release lever, left 1 5 Back roller 1 6 CIS release lever, right 1 7

Back roller bearing, right

1 8 Reduction gear, 17/28z 1 9 Reduction gear, 17/23z 1

(UX-40/FO-50 only)

10 Feed roller shaft 1

(UX-40/FO-50 only)

3 – 4

CIS unit and scanner frame

Hook

2 3 4 5

7 8 9

12 13

Fix position

Fix position of CSI spring

Page 36

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 3

3 – 5

Operation panel unit/

document guide upper unit 10 Screw 1 11 Pinion gear 1 12 Hopper spring 1 13 Hopper guide, left 1 14 Hopper guide, right 1 15 Hopper guide 1

Parts list (Fig. 3)

No. Part name Q’ty No. Part name Q’ty

1 Mechanism unit 1 2 Connector 2 3 Operation panel unit 1 4 Connector 2 5 Screw (3×12) 1 6 Drive unit 1 7 Screw (3×8) 2 8 Hopper guide unit 1

Operation panel unit, drive unit, hopper guide

Control PWB

2 3 7

11 12 13

4 5 6

GAP 0

HOPPER GUIDE(L)

HOPPER GUIDE(R)

30°

Fix position

boss

Rib

Confirm of HOPPER GUIDE position.

Page 37

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 4

3 – 6

Upper cabinet and document guide upper

12 Document guide piece 1

(UX-8/GQ-5 only) 13 Document guide upper 1 14 Screw (2×6) 3 15 Connector 1 16

Operation panel PWB unit

17 Direct key 1

(UX-40/FO-50 only) 18 Start key 1 19 12 key 1 20 Upper cabinet 1

Parts list (Fig. 4)

No. Part name Q’ty No. Part name Q’ty

1 Screw (3×8) 2 2 Connector 1 3 Door sensor 1 4 Blind sheet 1 5

Document guide upper unit

1 6 Operation panel unit 1 7 Separate spring 1 8 Separator plate 1 9 Separator rubber 1

10 Feed spring 1 11 Feed plate 1

LCD PWB

Rib

LCD CABLE

Note) The LCD PWB should be securely locked by the click of the panel case.

Fix position

Page 38

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 5

3 – 7

10 Planet lever B 1 11 Planet gear 1 12 Planet gear spring 1 13 Reduction gear, 17/30Z 1 14 Reduction gear, 17/43Z 1 15 Idler gear, 25Z 1 16 Screw (3×8) 1 17 Motor 1 18 Motor plate 1 19 Drive unit frame 1

1 Cam spring 1 2 Cam switch 1 3 Cam gear 1 4 Mode lever 1 5 Planet gear 1 6 Planet gear spring 1 7 Planet lever A 1 8 Planet gear 1 9 Planet gear spring 1

Parts list (Fig. 5)

No. Part name Q’ty No. Part name Q’ty

Drive unit frame

2 3 4

8 9

13 14 15

17 18 19

Grease

, ,

Nail be doing lock.

, ,

OK NG

Page 39

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Release lever, head guide and PO guide

Fig. 6

3 – 8

Parts list (Fig. 6)

No. Part name Q’ty

1 Mechanism unit 1 2 Screw (3×8) 1 3 PO guide 1 4 Release lever 1 5 Head guide 1

2 3 4 5

RELEASE

Page 40

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 7

3 – 9

Parts list (Fig. 7)

No. Part name Q’ty

1 Mechanism unit 1 2 Screw (3×6) 1 3 Connector 1 4 Screw (3×8) 1 5 Head earth cable 1 6 Head frame unit 1 7 Screw (3×8) 2 8 Panel lock lever spring 2

Head frame unit

2 3 4 5

7 8

Control PWB

Page 41

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 8

3 – 10

Head frame and thermal head

Parts list (Fig. 8)

No. Part name Q’ty No. Part name Q’ty

1 Platen gear 1 2 Platen bearing 2 3 Platen roller 1 4 Connector 1 5 Screw (3×6) 1 6 Head holder, left 1

7 Screw (3×6) 1 8 Head holder, right 1

9 Thermal head 1 10 Head spring 2 2 11 Head spring 1 3 12 Head frame 1

Page 42

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Fig. 9

3 – 11

11 Screw (3×8) 2 12 Hook switch joint lever 1 13

PWB case, top

PWB case, bottom unit

1 15 Screw (3×6) 1 16 TEL/LIU PWB unit 1 17 Screw (4×6) 1 18 AC cord ass’y 1 19 Power supply PWB unit 1 20 PWB case, bottom 1

Parts list (Fig. 9)

No. Part name Q’ty No. Part name Q’ty

1 Mechanism unit 1 2 Screw (3×8) 1 3 Connector 1 4 Connector 2 5

PWB case unit

1 6 Screw (3×8) 1 7 Control PWB unit 1 8 Screw (3×8) 1 9

Speaker holder lever spring

10 Speaker ass’y 1

PWB case top, bottom, PWB and speaker

Hook

12 13 14 15

17 18 19

Fix position

2 3 4 5

7 8 9

Page 43

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Wire treatment

Fig. 10

3 – 12

Parts list (Fig. 10)

1 Core (F2125) 2 2 Screw (3×6) 1 3 Screw (4×6) 1 4 Screw (3×6) 1 5 Band (100mm) 1 6 Band (100mm) (UX-40/FO-50 only) 2 7 Core (F2123) (UX-40/FO-50 only) 1 8 Screw (3x8) 1

No. Part name Q’ty

CIS

cable Front sensor cable(UX-40/ FO-50 ONLY)

Door sensor cable

Head cable

Control PWB

Motor cable

Cam switch cable

Rib

Panel cable

Hopper cover

PWB case, bottom

AC cord earth cable

ARG cable

TEL/LIU PWB

Power supply PWB

AC cord

Operation panel PWB

Operation panel unit

Rib

Speaker

Rib

TEL/LIU PWB

Power Supply PWB

The panel cable and door sensor cable pass to the core 2 times.

The head cable and head earth cable pass to the core 2 times.

Speaker cable

Speaker

Panel cable

Speaker cable

Head earth cable

Rib

CIS

cable CIS cable

Front sensor cable (UX-40/ FO-50 ONLY)

Scanner frame

Rib

Motor cable

Rib

Cam switch cable

Drive unit

CIS cable

Front sensor cable

Page 44

UX-8TH/UX-40TH GQ-5TH/FO-50TH

4 – 1

[1] Block diagram

CHAPTER 4. DIAGRAMS

SRAM

256kbit

ROM

1Mbit

CPU

CPU I/F

TIMER

RTC

PIO

WATCHDOG

TIMER

CLOCK

32.768kHz

INTERRUPT

CONTROLLER

CIS I/F

MOTOR I/F

SENSOR I/F

SIO

THERMAL

HEAD I/F

PANEL I/F

OPERATION

PANEL

CONTROL PWB UNIT

1CHIP FAX ENGINE (FC200)

HANDSET

SPEAKER

+5V +24V

OPERATION

PANEL

TEL/LIU

PWB UNIT

DRIVER

THERMAL

HEAD

CONTACT

IMAGE

SENSOR

POWER SUPPLY

PWB UNIT

STABILIZER

MODEM

FM209

AMPLIFIER

SURGE

PROTECT/

FILTER

CML TRANSFORMER

VBT

RECTIFIER

TRANSFORMER

RECTIFIER

DIODE

TRANS

SURGE

ABSORBER

FILTER

LINE

PAPER

SENSOR

RESET IC

AMPLIFIER

CLOCK

32.256MHz

LCD

D-FF

16MHz

+3.3V

+5V

REGULATOR

AMPLIFIER

Page 45

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[2] Wiring diagram

4 – 2

CNCIS

CNDR

CNTH

DOOR

SENSOR

CNPW

CN2

CNLIUA

CNLNJ

CNLIUA

CNFRS

FRONT

SENSOR

CNSP

CNCSWCNMT

CAM SW

TX/RX

MOTOR

CNPN

SPEAKER

CNPN

CNLCD

OPERATION

PANEL PWB

UNIT

LCD UNIT

THERMAL HEAD

CIS(CONTACT IMAGE SENSOR)UNIT

HANDSET

ARG

CNHJ

TEL/LIU

PWB UNIT

POWER SUPPLY

PWB UNIT

CONTROL

PWB UNIT

AC CORD

CNTLJ

(UX-40/FO-50 ONLY)

Page 46

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[3] Point- to-point diagram

4 – 3

TX/RX

MOTOR

TPAD TPBD TPAD TPBD

VMT VMT

1 2 3 4 5 6

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 2 3 4 5 6

OPERATION

PANEL

PWB

TPAD TPBD TPAD TPBD

VMT VMT

THERMAL

HEAD

VTH

VTH STRB1 STRB2

THI

N.C.

MG MG MG

+5V STRB3 STRB4 LATCH

PCLK DATA

VTH

VTH STRB1 STRB2

THI

RANK

MG MG MG

+5V STRB3 STRB4 LATCH

PCLK

DATA

VTH

1 2 3 4 5 6 7

+5V

øT

CISCLK

GLED

+24V

VO DG

+5V

øT

CISCLK

GLED

+24V

+5V

SEN4

E SEN0 SEN1 SEN2 SEN3 SEN5 SEN6 SEN7

ORGSNS

KEN4A KEN3A KEN2A KEN1A

+5V

SEN4

E SEN0 SEN1 SEN2 SEN3 SEN5 SEN6 SEN7

ORGSNS

KEN4A KEN3A KEN2A KEN1A

CNPN CNPN

CNCIS

1 2 3 4 5 6 7 8

9 10 11 12

1 2 3 4 5 6 7 8

9 10 11 12

TEL/LIU

PWB

TELOUT

TELIN

TELMUTE

RHS

RXIN

TXOUT

CML

+5V

+24V

TELOUT

TELIN

TELMUTE

RHS

RXIN

TXOUT

CML

+5V

+24V

CNLIUACNLIUA

CNMT

CNTH

1 2 3 4 5 6

POWER SUPPLY

PWB

DG +5V MG MG

+24V +24V

+5V

MG +24V +24V

CN2

CNPW

CNCSW

CNSP

CIS

1 2

CSW

CAM

SWITCH

1 2

SP+

SP-

CSW

SP+

SP-

SPEAKER

CONTROL

PWB

CNFRS

1 2

FRSNS

FRONT

SENSOR

CNDR

1 2

DRSNS

DOOR

SENSOR

(UX-40/FO-50 ONLY)

Page 47

UX-8TH/UX-40TH GQ-5TH/FO-50TH

CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT

[1] Control PWB circuit 1/6

Main control block

6 – 1

BDEFG

HCA

BDEFG

HCA

107

7374757677

798082838485868789909192939496

100

101

33343536293031

114

115

116

117

118

103

104

105

106

119

140

123

102

53.56

64.88

95.108

134

129

131

135

133

130

136

137

138

139

+5V

C120

0.1

C121

+5V

141

142

143

144

(3-3A) (3-3B)

SYSCLK MIRQ

R132

10K

C107

1000P

R107 33K

R106 33K

R105 33K

RA3

270 x 4

RA2

270 x 4

(2-5B)

(3-4B)

C112

C124

C140

C123

C122

C111

C106

C114

2345689

111213151617181920222324252627

128

127

120

12257121

126

124

125

113

112

111

109

110

ABCDEFG

A16

A15

A14

A13

A12

A11

A10

A9A8A7A6A5A4A3A2A1

RA6

270 x 4

RA7

270 x 4

IKJ

(2-5B)

(3-4B)

(2-4E)(3-3B)

(2-4B)

(2-4E)

(3-3B)

R112 200

R104 270

VBT

C134

R131

C137

0.1 DG

BATRST

+5V

VCC

GND

OUT

C165

MCS

CE1

ROMCS

(1-1F)

RESET

IC101

XC61

(1-1I)

RESET

C135

2200P

R12

10M

C138

22P

C139

22P

32.768KHz

(5-2D)

+VREF

(5-2D)

–VREF

(5-6D)

VIN

(5-1I)

THADI

(6-4I)

BZOUT

(5-5F)

TPA

(5-5F)

TPB

(5-5F)

TPA

(5-5F)

TPB

C136

DGDG

DG DG DG DG

C104 1000P

C105 1000P

C1 1000P

C2 1000P

RA5

470 x 4

(5-5F)

VTHON

(5-5F)

LEDON

(3-2C)

MDMRST

(6-6C)(6-2A)

RCVOL

0.1 +5V

CNPN-16 CNPN-15 CNPN-14 CNPN-13

CNPN-4 CNPN-5 CNPN-6 CNPN-7 CNPN-8 CNPN-3 CNPN-9 CNPN10 CNPN-11

KEN1A KEN2A KEN3A KEN4A

E SEN0 SEN1 SEN2 SEN3 SEN4 SEN5 SEN6 SEN7

L104

HM601

R133

120

RA8

470 x 4

RA13

470 x 4

A23

A22

A21

A20

A19

A18

A17

A16

A15

A14

A13

A12

A11

A10

A9A8A7A6A5A4A3A2A1

ROMCS

CS1

CS0

MCS

SYNC

REGDMA

WAIT

RAS

CAS0

CAS1

DWR

WRPROT

VBAT

CNTH-13

LATCH

CNTH-15

DATA

CNTH-14

PCLK

CNTH-3

STRB1

CNTH-4

STRB2

CNTH-11

STRB3

CNTH-12

STRB4

RA11

470 x 4

RA9

270 x 4

C125 22P

C126 22P

C115 22P

C116 22P

C141 22P

C150 22P

C142 22P

CNCIS-4

CNCIS-5

CISCLK

D[7-0]

A[16-0]

R109 150

R110 470

L101

HM601

(4-3D)

PSNS

(4-5D)

ORGSNSI

(4-5D)

FRSNSI

(4-4D)

PESNS

CNLIUB-4

DPMUTE

C162

N.M.

R118

470

RA4

470 x 4

R113 33K

R111 33K

R120 33K

R119 33K

CNLIUB-5

ERLY

CNLIUB-3

DPON

CNPW-8

PSAVE

CNLIUB-1

RLYCNT

(4-6D)

CSWI

C169 C163 C149 C168

N.M.

RA10

N.M.

R103

470

R126

33K

R169

470

CNLIUA-4

CNLIUA-5

(6-4I)

SPMUTE

(1-6B)

CML

(5-2A)

VREFCONT

(4-4D)

CUTI

CML

GPIO20

GPIO19

GPIO18

GPIO17

GPIO16

GPIO15

GPIO14

GPIO13

GPIO12

GPIO11

GPIO10

GPIO9

GPIO8

GPIO7

GPIO6

GPIO5

GPIO4

GPIO3

GPIO2

GPIO1

GPIO0

VIDCTL0

VIDCTL1

CLK1

CLK2

START

STRB3

STRB2

STRB1

STRB0

PCLK

PDAT

PLAT

STRBPOL

D0 D1 D2 D3 D4 D5 D6 D7 TSTCLK SYSCLK MIRQ RESET DEBUG TEST

VSS

VDD VDD VDD VDD VDD VDD VDD VDD

ADXG

ADGA ADGD

ADVA

BATRST

PWRDWN

XOUT

XIN

+VREF

–VREF / CLREF

VIN

THADI

TONE

SM0 SM1 SM2 SM3

GPO0 GPO1 GPO2 GPO3

VDRAM

OPI0 OPI1 OPI2 OPI3

LEDCTL

LCDCS

OPO0 OPO1 OPO2 OPO3 OPO4 OPO5 OPO6

38 : OPO7

R144

10K

RA1

470 x 4

R168

10K

RA12

470 x 4

R166

RA14 470

R123 33K

R124 33K

R125 33K

(2-4B)(3-3B)

RA10

N.M.

IC2

FC200

FAX ENGINE

CNLIUA-9

CML

(1-5A)(6-3E)

N.M.

Page 48

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Memory block 2/6

6 – 2

BDEFG

HCA

BDEFG

HCA

2029192818

172515231426132731

IO8

IO7

A14

IO6

A13

IO5

A12

IO4

A11

IO3

A10

IO2

IO1

A5 VDD

VSS

27A022

CS2/OE

A[16~0]

(1-5I)

D[7~0]

(1-6I)

(1-3I)RD(1-3I)

+5V

C161

0.1

D7D6D5D4D3D2D1

IC5

27C010

ROM

A15 DQ8

A14 DQ7

A13 DQ6

A12 DQ54A11 DQ4

A10 DQ3

A9 DQ2

A8 DQ1

A75A66A5

PGM

VCC

VPP

A2A1A0 GNDEG

IC3

W24258S-70LE

SRAM

D7D6D5D4D3D2D1

VBT

C113

0.1

(1-3I)

VBT

R121

22K

ROMCS

A16

A15

A14

A13

A12

A11

A10A9A8A7A6A5A4A3A2A1A0

A16

(A17)

CS1

CE1

(1-3I)

Page 49

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Modem block 3/6

6 – 3

BDEFG

HCA

BDEFG

HCA

0.01

R167

270

D6D5D4D3D2D1D0

A1A2A3

1920212223

RS4

RS3

RS2

RS1

RS0

78D779D680D581D482D383D286D188D091CS92

READ90WRITE

108

IRQ1

115

RESET13EN85

D[7~0]

(1-3I)

R116

MIRQ

(1-6F)

A[4~0]

MDMRST

(1-1D)

MCS

MAG

121

IRQ2

N.M.

107

RTS

CTS

TXD

DCLK

RXD11RLSD

10K

RESERVED/CSBR

119

270

+5V

SYSCLK

(1-6F)

621

XCLK

YCLK

CLR

CLK

PRE

HM601

R102

470

L105

HM601

C103

IC1

TC7WT74

HM601

101

102

104

105

109

110

111

RA14

470 x 1

R122

10K

TXMUTE

TELMUTE

DGDG DG DG DG DG DG

R101

C102

12P

C101

12P

R100

200

122

116

117

414043344746373635

1,2,53,103,118,123,124,128

38,39,44,49,59,64,65,74

MAG

0.1 C131

0.1

10/50C510/50

MAG

(6-5E)

SPOUT

(6-4C)

TELOUTI

(6-4E)

SIGTX

(6-4E)

SIGRX

C130

0.1

R134

2.2K

R129

MAG

CNDR-1

DRSNS

C119

2200P

R115

470

+5V

R165

100K

120

CNTH-6

RANK

CNLIUA-6

RHS

R117

470

RA14

470 x 1

+3.3V

L103

HM601

C133

100

112

106

114

125

113

126

+5V

L100

HM601

C110

0.1

+3.3V

R14

47/25

C132

127

C118

0.1

+5V

L102

HM601

MAG

MICP-P

MICM-P

MICBIAS-P

SPKRP-P

SPKRM-P

LINEIN-P

LINEOUT-P

VREF-P

VC-P

RESERVED

N.C./MICM-S

N.C./SPKRP-S

N.C./LINEIN-S

N.C./VREF-S

N.C./MICP-S

N.C./MICBIAS-S

N.C./SPKRM-S

N.C./LINEOUT-S

N.C./VC-S

N.C.

XTL0

XTL1

N.C./SOUT-S

SR3IN

SOUT-P

N.C./ICLK-S

ICLK-P

IA1CLK

N.C./SIN-S

SIN-P

SR4OUT

N.C./MCLK-S

IACLK

MCLK-P

N.C./FSYNC-S

SA1CLK

FSYNC-P

N.C./CTRLSIN-S

CTRLSIN-P

SR1IO

EYEXY

EYECLK

EYESYNC

N.C./IARESET-S

IARESET-P

GPO0 GPO1 GPO2 GPO3 GPO4 GPO5 GPO6 GPO7

GPI7

GPI6

GPI5

GPI4

GPI3

GPI2

GPI1

GPI0

VDD1(+3.3VDD)

VDD2(+3.3VDD)

VDD3(+3.3VDD)

VDD4(+3.3VDD)

VDD5(+3.3VDD)

AVDD-P(+3.3VIAD)

DGND1

DGND2

DGND3

DGND4

DGND5

DGND6

VGG(+5VDD)

DVAA(+3.3VDA)

N.C./AVDD-S(+3.3VIAD)

AGND1

AGND2

AGND3

AGND4

AGND5

VAA-P(+5VIAA)

VAA-S(+5VIAA)

R135

33K

R130

32.256MHz

CNLIUA-3 CNLIUB-2

(1-6H)

(1-5I)

IC4

FM209

MODEM

C19

1000P

C172

1000P

TXMUTEI(6-4E)

C173

1000P

C20

1000P

MAG

N.M.

Page 50

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Sensor/Reset/Power supply block 4/6

6 – 4

BDEFG

HCA

BDEFG

HCA

N.M.

CNCSW-1

CNCSW-2

CSW

(1-4A)

CNFRS-1

CNFRS-2

FRSNS

(1-3A)

CNPN-12

ORGSNS

(1-3A)

(1-4A)

+24V

C108

2200P

CSWI

C109

2200P

FRSNSI

C143

2200P

ORGSNSI

PESNS

R145

R114

N.M.

(1-3A)

PSNS

DGDG

PESNS

PSNS

PI2

SG206

PI1

CNCUT-1

CNCUT-3

CUT

(1-5A)

C117

CUTI

+5V

R160

5.6K

BAT1

CR2032

D103

HRW0202

VBT

<VBT>

+3.3V

D102

1SS355

REG100

XC62FP3302P

C167

0.1

DG DG

+5V

+24V

+24VA

C17

22/50

C170

0.1

R159

N.M.

R164

N.M.

C18

47/25

C171

0.1

+5V

+24V

+5V

+24V

CNLIUA-10

CNPN-2

CNLIUA-11

CNPN-1

CNLIUA-12

CNPW-2

CNPW-1

CNPW-7

CNPW-5

CNPW-6

CNPW-3

CNPW-4

R163

C16

N.M.

CNCUT-2

N.C.

(UX-40/

FO-50

ONLY)

(UX-40/

FO-50

ONLY)

N.M.

Page 51

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Video processing/Motor drive / Thermal block 5/6

6 – 5

BDEFG

HCA

BDEFG

HCA

R128

5.1K

+5V

Q100

2SA1037

CNCIS-1

<VO>

(1-1F)

<VIN>

VIN

C128

1000P

+5V

CNCIS-3

CNCIS-2

<DG>

+5V

+24V

CNCIS-7

+24V

C127

C100

0.1

GLED

CNCIS-6

C129

0.1

LEDON

R158

5.1K DG

Q104

2SA1037

(1-5A)

VREFCONT

(1-1F)

VREF+

+5V

R157

20K

(1-1F)

VREF–

R142

30K

R143

43K

9161514131211

1234567

TPA

TPB

TPA

TPB

VTHON

LEDON

(1-1E)

(3-1D)

+24V

FU100

KAB2402

100(1W)

VMT

TPBD

TPAD

TPBD

TPAD

VTHON

LEDON

CNMT-5

CNMT-6

CNMT-1

CNMT-2

CNMT-3

CNMT-4

(5-3E)

(5-4B)

IC8

ULN2003A

1B2B3B4B5B6B7B

COM

1C2C3C4C5C6C7C

VTHON

(5-5I)

+24V

D104

1SS355

RY1

DQ1U24VDC

+24V

VTH

CNTH-1

VTH

CNTH-2

VTH

CNTH-16MGCNTH-7MGCNTH-8MGCNTH-9

R108

22K

+5V

CNTH-10

+5V

(1-1F)

CNTH-5

THI

THADI

C166

R162

20K

R161

470K

C15

10/50

COIL

C21

R170

N.M.

(5-5I)

C174

N.M.

Page 52

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Analog signal block 6/6

6 – 6

BDEFG

HCA

BDEFG

HCA

–

+5V

+5VA

+5V

–

+5VA

+5V

(1-1D)

RCVOL

TELOUT

CNLIUA-1

C151

R148

C155

N.M.

R150

N.M.

IC7

R1460R147

N.M.

C152

Q101

N.M.

R136

C144

HM601

R137

N.M.

C145

D100

1SS355

TELOUTI

(3-4H)

SIGTX

(3-4H)

TXOUT

CNLIUA-8

(3-3H)

SPOUT

+5V

R154

100K

C159

220P

R139

220K

C11

47/25

SP+

SP–

CNSP-1

CNSP-2

(1-5A)

SPMUTE

C158

DG DG

(1-1F)

BZOUT

R156

C164

4700P

R141

20K

RXIN

CNLIUA-7

C157

R152

R15

N.M.

R18

R17

N.M.

C14

N.M.

R138

C147

HM601

C146

R16

N.M.

SIGRX

(3-4H)

CML

(1-5A)

Q102

TELIN

CNLIUA-7

C156

C154

0.1

R153

330K

RCVOL

(1-1E)

R151

R149

Q103

C22

D101

1SS355

IC7

DG DG

R155

100K

C160

0.01

R140

15K

C148

0.1

IC6

NJM2113

N.M.

(3-1D)

TXMUTEI

HM601

L106

HM601

+24VA

C153

N.M.

Page 53

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Control PWB parts layout (Top side)

6 – 7

Page 54

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Control PWB parts layout (Bottom side)

6 – 8

Page 55

UX-8TH/UX-40TH GQ-5TH/FO-50TH

6 – 9

[2] TEL/LIU PWB circuit 1/2

BDEFG

HCA

BDEFG

HCA

–

+5VA

–

+5VA

+24VA

+5V

VREF

+5V

–

VREF

+5V

–

VREF

L3B

R-5C

N.M.

JP17

N.M.

JP16

TLJ-2

CNLNJ-2

JP13

JP10

JP8

CNLNJ-3

JP9

JP6

CNLNJ-4

VA2

ERZV5D471

VA1

ERZV5D471

ARG

CNLNJ-5

JP11

TLJ-1

JP12

JP1

JP15

C102

C101

N.M.

L3A

R-5C

N.M.

JP3

N.M.

CML1

0.82

R101

43K

22K(1/2W)

1SS133

ZD4

HZ27C

PC5

TLP521

R103

N.M.

I2164

C103 C116

N.M.

–

REC1

CNLNJ-6

PC4

PC1

PC2

R104

ZD1

R105

R102

R107

PC3

R106

N.M.

ZD8

ZD7

JP4

C11

22/50

JP2

+5V

C10

N.M.

R117

R129

620

JP14

4.7/50

C127

0.039

C123

N.M.

R133

51K

R116

3.3K DG

C115

33P

R115

86.6K

IC102

2904

R114

4.7K

TXOUT

CNLIUA-8

R137

C125

R139

C126

R138

N.M.

C124

C122

R134

20K

R140

20K

R141

47K

C120

820P

C121

R143

47K

N.M.

IC102

2904

RXIN

CNLIUA-7

R142

3.3K DG

C112

0.1

C114

0.1

IC101

2904

IC102

2904

R111

20K

R113

20K

R112

10/50

DGDG

CNHJ-4

CNHJ1-4

CNHJ-1

CNHJ1-1

TX+

TX–

C104

2200P

CNHJ1-2

CNHJ-2

CNHJ1-3

CNHJ-3

RX+

RX–

R-5C

R108

1.5K

R109

22/50

C105

2200P

C106

0.1

R110

5.1K

ZD5 ZD6

N.M.

C108

3900P

R114

43K

C109

220P

R131

3.3K

C113

1000P

C107

1000P

DGDGDG

N.M.

IC101

2904

R130

TELOUT

CNLIUA-1

D3 D2

N.M.

R-5C

22/50

R123

150

R124

N.M.

R125

3.3K

IC101

2904

C111

220P

R126

220K

C14

N.M.

TELIN

CNLIUA-2

R127

68K

R128

8.2K

TELMUTE

CNLIUA-3

R132

Q107

RNC1402

JP7

AR1

RA-391P

ZD2

Q101

2SC2412K

JP5

ZD3

N.M.

NOTE:

These marks are all satety-cirtical parts.

N.M.

JP18

Page 56

UX-8TH/UX-40TH GQ-5TH/FO-50TH

6 – 10

TEL/LIU PWB circuit 2/2

BDEFG

HCA

BDEFG

HCA

+5V

DPON

CNLIUB-3

DPMUTE

CNLIUB-4

E-RLY

CNLIUB-5

R119

PC1

Q105

Q106

Q108

R120

R121

PC2

PC4

CNLIUA-4

R122

DGDG

C110

PC5

TLP521

CNLIUA-5

R136

DGDG

C119

PC3

N.M.

RHS

CNLIUA-6DGCNHS-1

CNHS-2

SW1

HOOK SW

CNLIUA-10

+5V

CNLIUA-11DGCNLIUA-12

+24V

R118

100

C13

22/25

C12

22/50

C117

0.1

C118

0.1

+5VA

+24VA

R135

CNLIUA-9

CML

1SS133

Q104

RNC1402

N.M.

CML

Page 57

UX-8TH/UX-40TH GQ-5TH/FO-50TH

TEL/LIU PWB parts layout (Top side)

6 – 11

Page 58

UX-8TH/UX-40TH GQ-5TH/FO-50TH

6 – 12

TEL/LIU PWB parts layout (Bottom side)

Page 59

UX-8TH/UX-40TH GQ-5TH/FO-50TH

6 – 13

[3] Power supply PWB circuit

CH2 W1

50.0V

25.00us

-50.0V

-25.00us

GND

10V/div

5us/div

CH2 W1

100.0V

25.00us

-100.0V

-25.00us

GND

20V/div

5us/div

CH2 W1

1200V

25.00us

-800V

-25.00us

GND

200V/div

5us/div

CH2 W1

450V

5.02ms

-50V

-4.9Sms

GND

50V/div

1ms/div

CH2 W1

100.0V

25.00us

-100.0V

-25.00us

GND

20V/div

5us/div

BDEFG

HCA

BDEFG

HCA

S3L20U-4004P15

C13

PTTP124

FB1

R11

ZD7

RD20ESAB

PC2

PC123YS

2SC4210

R21

150K

2SC4210

R12

180K

ZD4

RD30FB

R20

4.7K

IC1

UPC29M05AHF

R19

4.7K

JUMPER

CCP2E100(4A)

R25

10K

C16

100/10

0.47

R16

22K

C12

0.1

R15

330K

R14

1.5K

R13

4.7K

PC1

PC123YS

R18

27K

2SC2412K

ZD5

RD6.2SB

VR1

R17

8,2K

C10

2200/16

SR140

N.M.

C23

R24

ZD6

RS208

330

2200P

PC2

PC123YS

ZD2

RD2.0SB

1SS355

PC1

C17

1000P

C24

0.22

FS5KM

1000P

ZD1

RD27SB

2SD2114K

2SC2412K

470

R10

0.33

47K

3900P

1.6A/250V

CN1

1.6A/250V

0.22

3.3M 1

ERZV07D471

ELF15N003A

C15

2200P

C21

D2D1

TH1

89.2

N.M.

CN2

+5V

+24V

PSAVE

68/400

560/35

*R5

1.5K *R6

18K

*:ADJUSTMENT RESISTOR

ERA15-06 x 4

Page 60

UX-8TH/UX-40TH GQ-5TH/FO-50TH

Power supply PWB parts layout (Top side)

6 – 14

Power supply PWB parts layout (Bottom side)

R8R9Q3

ZD1

C23

C4R4

R11

R16

R25

R15

C12

ZD5

R17

Q6 R12

R19

R18

R21

R13

R20

R14

C17

ZD2

C13

IC1

ZD7

FB1

C10

C16

ZD4

VR1

R24

ZD6

R10

CN1

C15

C21

J10

J11

J12

JW1

TH1

C24

PC2

PC1

CN2

Page 61

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[4] Operation panel PWB circuit

6 – 15

BDEFG

HCA

BDEFG

HCA

LD4

1SS270

CNLCD-11

CNPN-5

LD5

1SS270

CNLCD-12

CNPN-6

123

456

VOLUME

SEN0

SEN1

LD6

1SS270

CNLCD-13

CNPN-7

789

FUNC

SEN2

LD7

1SS270

CNLCD-14

CNPN-8

RESO/MODE

SEN3

1SS270

CNLCD-4

CNPN-3

SEN4

02 04

1SS270

CNPN-9

STOP

SEN5

START COPY

1SS270

CNPN-10

HOLD

REDIAL

SEN6

SPEED SPEAKER

CNPN-11

PLAY

REC

SEN7

REPEAT DELETE

CNPN-16

KEN1A

CNPN-15

KEN2A

CNPN-14

KEN3A

CNPN-13

KEN4A

N.M.

CNPN-12

ORGSNS

SW-169-72AU

CNLCD-6

CNPN-4

CNLCD-2

+5V

CNPN-2

+5V

CNLCD-1

CNPN-1

CNLCD-5

R/W

CNLCD-3

C2 C1

6.2K

12345678910

11 12

13 14

15 16

CNPN

SEN4

SEN0

SEN2

SEN5

SEN7

KEN4A

KEN2A

SEN1

SEN3

SEN6

ORGSNS

KEN3A

KEN1A

+5V

12345678910

11 12

13 14

CNLCD

DGVOR/W

N.C.

LD4

LD6

RSEN.C.

N.C.

LD5

LD7

+5V

ORGSNS

N.M.

NOTE: Since the parts of PWB cannot be supplied, change it as a unit.

(UX-40/

FO-50

ONLY)

(UX-40/

FO-50

ONLY)

(UX-40/

FO-50

ONLY)

(UX-40/

FO-50

ONLY)

(UX-40/

FO-50

ONLY)

Page 62

UX-8TH/UX-40TH GQ-5TH/FO-50TH

6 – 16

M E M O

Page 63

UX-8TH/UX-40TH GQ-5TH/FO-50TH

CONTENTS

PARTS GUIDE

UX-8

UX-40 GQ-5

MODEL FO-50

Because parts marked with " " is indispensable for the machine safety maintenance and operation, it must be replaced with the parts specific to the product specification.

1 Cabinet, etc.

2 Scanner unit

3 Upper cabinet

4 Document guide upper

5 Drive unit

6 P acking material & Accessories

7 Control PWB unit

8 TEL-Liu PWB unit

9 Power supply PWB unit

Index

Page 64

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[1] Cabinet, etc.

– 1 –

SCANNER UNIT

DOCUMENT GUIDE UPPER

B3x2

B7x2

DRIVE UNIT

Page 65

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 2 –

[1] Cabinet etc.

1 DCEKP481BXH18 AP N E Operation panel unit [8]

DCEKP481BXH04 AP E Operation panel unit [40] DCEKP481BXH19 AP N E Operation panel unit [5]

DCEKP481BXH05 AP E Operation panel unit [50] 2 CCNW-212AXH01 AK C Panel cable ass’y 5 MSPRC2954XHZZ AC C Hopper spring 6 NGERP2318XHZZ AD C Pinion gear 7 PGIDM2560XHSD AE C Hopper,guide,left 8 PGIDM2561XHSD AC C Hopper,guide,right 9 PHOP-2104XHSD AF C Hopper cover

11 QSW-M2296XHZZ AD B Door sensor 12 CCNW-215AXH01 AG C Speaker ass’y 13 GCABB2343XHSA AK D Lower cabinet [8/40]

GCABB2343XHSB AK N D Lower cabinet [5]

GCABB2343XHSC AK D Lower cabinet [50]

14 MSPRP3119XHZZ AC C Panel lock lever spring 15 MSPRP3123XHZZ AC C Speaker holder lever spring 16 DCEKL483BXH02 AX E TEL/Liu PWB unit 17 GCASP2110XHSD AK C PWB case,top [8/40]

GCASP2110XHSF AK N C PWB case,top [5]

GCASP2110XHSE AK C PWB case,top [50]

18 GCASP2111XHSA AH C PWB case,bottom [8/40]

GCASP2111XHSB AH N C PWB case,bottom [5]

GCASP2111XHSC AH N C PWB case,bottom [50]

19 MLEVP2320XHZZ AC C Hook switch joint lever 20 QACCE2042XHZZ AL B AC cord ass’y

21 RDENT2144XHZZ BA E Power supply PWB unit 22 GDAI-2083XHZZ AF C Paper support guide 23 MLEVP2316XHZZ AC C Paper sensor lever 24 MSPRD3116XHZZ AB C Paper sensor lever spring 27 PGIDM2563XHSA AE N C PO guide [8/40]

PGIDM2563XHSB AE N C PO guide [5]

PGIDM2563XHSC AC N C PO guide [50]

28 LBSHP2112XHZZ AB C Platen bearing 29 LFRM-2208XHZZ AF C Head frame 30 LHLDZ2184XHZZ AC C Head holder,left 31 LHLDZ2185XHZZ AC C Head holder,right 33 MSPRC3112XHZZ AC C Head spring 1 34 MSPRC3148XHZZ AC C Head spring 2 36 NGERH2478XHZZ AB C Platen gear 37 NROLR2425XHZZ AP C Platen roller 39 QCNW-209AXHZZ AH C Head cable 40 QCNW-210AXHZZ AC C Head earth cable 41 RHEDZ2059XHZZ BF B Thermal head 45 DCEKC689MXHZZ BP N E Control PWB unit(Within ROM) [8]

DCEKC685MXHZZ BP N E Control PWB unit(Within ROM) [40/50]

DCEKC780MXHZZ BP N E Control PWB unit(Within ROM) [5]

46 GDAI-2082XHSD AD C Handset cover 47 LSTPP2054XHZZ AC C Panel stopper 49 MLEVP2319XHZZ AC C Hook switch lever 52 PGIDM2566XHZZ AC C Head guide 53 RCORF2125XHZZ AE B Core(TRA31) 54 HPNLH2394XHSA AE N D Decoration panel [8]

HPNLH2392XHSU AE N D Decoration panel [40]

HPNLH2394XHSE AE N D Decoration panel [5]

HPNLH2392XHS3 AE N D Decoration panel [50]

55 LBNDJ2006XHZZ AA C Band(100mm) 56 PSHEZ3410XHZZ AB C Jack sheet

58 MLEVP2321XHZZ AN N C Release lever B1 LX-BZ2138XHZZ AB C Screw(2x6) B3 XEBSD30P08000 AA C Screw(3x8) B4 XBBSD30P06000 AA C Screw(3x6) B5 XBPSN40P06K00 AA C Screw(4x6) B7 XEBSD30P12000 AA C Screw(3x12)

Page 66

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[2] Scanner unit

– 3 –

: UX-40/FO-50 ONLY

[2] Scanner unit

1 LBSHP2110XHZZ AB C Back roller bearing 2 LFRM-2209XHZZ AF C Scanner frame 3 LHLDZ2180XHZZ AC C CIS support,left 4 LHLDZ2181XHZZ AC C CIS support,right 5 MLEVP2317XHZZ AB C CIS release lever 6 MSPRC3117XHZZ AB C CIS spring 7 NGERH2479XHZZ AB C Back roller gear 8 NGERH2480XHZZ AB C Reduction gear,17/28Z

9 NGERH2481XHZZ AB C Reduction gear,17/23Z [40/50] 10 NROLR2375XHZZ AL C Feed roller [40/50] 11 NROLR2428XHZZ AP C Back roller 12 NSFTZ2273XHZZ AF C Feed roller shaft [40/50] 13 PGIDM2562XHZA AD N C Document guide lower [8/5]

PGIDM2562XHZZ AD C Document guide lower [40/50] 14 PSHEZ3436XHZZ AC C CIS protect sheet 15 QCNW-211AXHZZ AF C CIS cable 16 QCNW-213AXHZZ AC C Front sensor cable [40/50] 17 QSW-M2293XHZZ AE B Front sensor [40/50] 18 RUNTZ2054XHZZ BE B CIS unit 19 LBNDJ2006XHZZ AA C Band(100mm) [40/50] 20 RCORF2123XHZZ AD B Core [40/50]

Page 67

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[4] Document guide upper

1 LPLTG2911XHZZ AE C Separator rubber [40/50] 2 LPLTP2908XHZZ AE C Separator plate [40/50] 3 LPLTP3051XHZZ AB C Feed plate [40/50] 4 MSPRT3140XHZZ AA C Separate spring [40/50] 5 MSPRT3139XHZZ AA C Feed spring [40/50] 6 PGIDM2554XHZZ AF C Document guide upper 7 PSHEZ3517XHZZ AE N C Blind sheet 8 LPLTP3058XHZZ AD N C Document guide piece [8/5]

– 4 –

[3] Upper cabinet

B2x3

(UX-40/FO-50 ONLY)

[4] Document guide upper

UX-40/ FO-50 ONLY

UX-8/GQ-5

ONLY

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

[3] Upper cabinet

1 CCNW-212AXH01 AK C Panel cable ass’y 3 GCABA2342XHSA AH D Upper cabinet [8/40]

GCABA2342XHSB AH N D Upper cabinet [5]

GCABA2342XHSC AH D Upper cabinet [50] 4 JBTN-2257XHSD AD C 12 key 5 JBTN-2258XHSA AC C Start key [8/40]

JBTN-2258XHSB AC N C Start key [5]

JBTN-2258XHSC AC C Start key [50] 6 JBTN-2261XHSA AC C Direct key [40]

JBTN-2261XHSC AC C Direct key [50] 7 DCEKP482BXH02 AP N E Operation panel PWB unit [8/5]

DCEKP482BXH01 AQ E Operation panel PWB unit [40/50]

B2 XUBSD20P06000 AA C Screw(2x6)

(Unit)

901 DCEKP481BXH18 AP N E Operation panel unit [8]

DCEKP481BXH04 AP E Operation panel unit [40]

DCEKP481BXH19 AP N E Operation panel unit [5]

DCEKP481BXH05 AP E Operation panel unit [50]

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

Page 68

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 5 –

[5] Drive unit

1 LFRM-2207XHZZ AF N C Drive unit frame 2 LPLTM3049XHZZ AD C Motor plate 4 MCAMP2027XHZZ AC C Cam 5 MLEVP2311XHZZ AB C Planet lever A 6 MLEVP2312XHZZ AB N C Planet lever B 8 MLEVP2314XHZZ AB C Mode lever

9 MSPRC2735XHZZ AC C Planet gear spring 10 MSPRC3110XHZZ AB C Cam spring 12 NGERH2278XHZZ AC C Planet gear 13 NGERH2379XHZZ AC C Idler gear,25Z 15 NGERH2391XHZZ AC C Reduction gear,17/30Z 17 NGERH2475XHZZ AB C Reduction gear,17/43Z 20 QCNW-4933XHZZ AC C Cam switch cable 21 QSW-F2224SCZZ AE B Cam switch 22 RMOTZ2148XHZZ AT B Motor

B3 XEBSD30P08000 AA C Screw(3x8)

Page 69

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[6] Packing material & Accessories

1 TINST4026XHZZ AY D Operation manual 2 DUNTK468BXHPU AH E Handset 3 QCNW-3976XHBG AK C Handset cord [8/40]

QCNW-3976XHOG AT C Handset cord [5]

QCNW-3976XHOW AK C Handset cord [50] 4 PHOP-2105XHZZ AD C Original document support 5 QCNW-3975XHGY AG C Telephone line cord 6 SPAKP296BXHZZ AE D Vinyl cover 7 SPAKA287BXHZZ AE D Packing add.,left 8 SPAKA288BXHZZ AE D Packing add.,right 9 SPAKA289BXHZZ AC D Pad

10 SPAKC178BXHZZ AH N D Packing case [8]

SPAKC189BXHZZ AH N D Packing case [40]

SPAKC187BXHZZ AH N D Packing case [5]

SPAKC194BXHZZ AH N D Packing case [50]

11 TLABM341AXHZZ AD N D Box label [8]

TLABM345AXHZZ AD N D Box label [40]

TLABM344AXHZZ AD N D Box label [5]

TLABM347AXHZZ AD N D Box label [50]

16 PGIDM2578XHZZ AE C Paper roll shim,right 17 PGIDM2579XHZZ AE C Paper roll shim,left 18 NSFTZ2320XHZZ AF C Paper shaft 19 TCADZ2935XHZZ AA D Caution sheet 21 SPAKA388BXHZZ AE D Protection sheet,left 22 SPAKA389BXHZZ AE D Protection sheet,right

[6] Packing material & Accessories

TAPE

AC CORD

ORIGINAL DOCUMENT SUPPORT SIDE

FAX PAPER

TAPE

(2)

(1)

(4)

(3)

– 6 –

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

Page 70

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 7 –

[7] Control PWB unit

1 UBATL2046SCZZ AK B Battery(CR2032T34) [BAT1] 2 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C1] 3 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C2] 4 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C3] 5 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C4] 6 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C5] 7 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C6] 8 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C7]

9 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C8] 10 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C9] 11 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C11] 12 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C15] 13 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C17] 14 VCEAGA1EW476M AA C Capacitor(25WV 47µF) [C18] 15 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C19] 16 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C20] 17 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C22] 18 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C100] 19 VCCCTV1HH120J AA C Capacitor(50WV 12PF) [C101] 20 VCCCTV1HH120J AA C Capacitor(50WV 12PF) [C102] 21 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C103] 22 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C104] 23 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C105] 24 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C106] 25 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C107] 26 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C108] 27 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C109][40/50] 28 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C110] 29 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C111] 30 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C112] 31 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C113] 32 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C114] 33 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C115] 34 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C116] 35 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C118] 36 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C119] 37 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C120] 38 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C121] 39 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C122] 40 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C123] 41 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C124] 42 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C125] 43 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C126] 44 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C127] 45 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C128] 46 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C129] 47 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C130] 48 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C131] 49 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C132] 50 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C133] 51 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C134] 52 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C135] 53 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C136] 54 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C137] 55 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C138] 56 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C139] 57 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C140] 58 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C141] 59 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C142] 60 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C143] 61 RCILZ2145XHZZ AF C Coil(HM601) [C144] 62 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C145] 63 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C146] 64 RCILZ2145XHZZ AF C Coil(HM601) [C147] 65 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C148] 66 VCCCTV1HH220J AA C Capacitor(50WV 22PF) [C150] 67 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C151] 68 VCKYTV1EB104K AA C Capacitor(25WV 0.1µF) [C154] 69 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C156] 70 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C157] 71 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C158] 72 VCKYTV1HB221K AA C Capacitor(50WV 220PF) [C159] 73 VCKYTV1HB103K AB C Capacitor(50WV 0.01µF) [C160] 74 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C161] 75 VCKYTV1HB472K AA C Capacitor(50WV 4700PF) [C164] 76 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C165] 77 VCKYTV1CF105Z AB C Capacitor(16WV 1µF) [C166] 78 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C167] 79 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C170] 80 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C171]

Page 71

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 8 –

[7] Control PWB unit

81 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C172] 82 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C173] 83 QCNCM7014SC0G AB C Connector(7pin) [CNCIS] 84 QCNCM2442SC0B AB C Conector(2pin) [CNCSW] 85 QCNCM705BAF06 AB C Connector(2pin) [CNDR] 86 QCNCM7014SC0B AD C Connector(2pin) [CNFRS][40/50] 87 QCNCW2500SC1B AF C Connector(12pin) [CNLIUA] 88 QCNCM7014SC0F AB C Connector(6pin) [CNMT] 89 QCNCM7014SC1F AD C Connector(16pin) [CNPN] 90 QCNCW2500SC0H AF C Connector(8pin) [CNPW] 91 QCNCM2401SC0B AA C Connector(2pin) [CNSP] 92 QCNCM7014SC1F AD C Connector(16pin) [CNTH] 93 VRS-HT3AA101J AA C Resistor(1W 100Ω ±5%) [D1] 94 VHD1SS355//-1 AB B Diode(1SS355) [D100] 95 VHD1SS355//-1 AB B Diode(1SS355) [D101] 96 VHD1SS355//-1 AB B Diode(1SS355) [D102] 97 VHDHRW0202B-1 AD B Diode(HRW0202B) [D103] 98 VHD1SS355//-1 AB B Diode(1SS355) [D104]

99 QFS-P2010SCZZ AD B IC protector(KAB2402) [FU100] 100 VHITC7WT74FU1 AF B IC(TC7WT74) [IC1] 101 VHIFC2FM209-1 BD B IC(FC200)(Within IC2 and IC4 pair) [IC2] 102 VHIW24258S7LE AQ B IC(W24258S-70LE) [IC3] 103 VHIFC2FM209-1 BD B IC(FM209)(Within IC2 and IC4 pair) [IC4] 104 QSOCZ2051SC32 AC C IC socket(32pin) [IC5]

VHI27010FZJ0B BM N B IC,EPROM(1MB) [IC5][8/5]

VHI27010FZK0A BM N B IC,EPROM(1MB) [IC5][40/50] 106 VHINJM2113M-1 AG B IC(NJM2113M) [IC6] 107 VHIULN2003AN/ AE B IC(ULN2003ANS) [IC8] 108 VHIXC61AN45M1 AE B IC(XC61AN4502ML) [IC101] 109 RCILZ2145XHZZ AF C Coil(HM601) [L1] 110 RCILZ2145XHZZ AF C Coil(HM601) [L3] 111 RCILZ2145XHZZ AF C Coil(HM601) [L4] 112 RCILZ2145XHZZ AF C Coil(HM601) [L100] 113 RCILZ2145XHZZ AF C Coil(HM601) [L101] 114 RCILZ2145XHZZ AF C Coil(HM601) [L102] 115 RCILZ2145XHZZ AF C Coil(HM601) [L103] 116 RCILZ2145XHZZ AF C Coil(HM601) [L104] 117 RCILZ2145XHZZ AF C Coil(HM601) [L105] 118 RCILZ2145XHZZ AF C Coil(HM601) [L106] 119 VHPSG206S//-1 AG B Photo transistor(SG206S) [PI2] 120 VS2SA1037KS-1 AB B Transistor(2SA1037KS) [Q100] 121 VS2SA1037KS-1 AB B Transistor(2SA1037KS) [Q104] 122 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R4] 123 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R6] 124 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R8] 125 VRS-TS2AD106J AA C Resistor(1/10W 10MΩ ±5%) [R12] 126 VRS-TS2AD3R0J AA C Resistor(1/10W 3.0Ω ±5%) [R14] 127 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R17] 128 VRS-TS2AD201J AG C Resistor(1/10W 200Ω ±5%) [R100] 129 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R101] 130 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R102] 131 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R103] 132 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R104] 133 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R105] 134 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R106] 135 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R107] 136 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R108] 137 VRS-TS2AD151J AA C Resistor(1/10W 150Ω ±5%) [R109] 138 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R110] 139 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R111] 140 VRS-TS2AD201J AG C Resistor(1/10W 200Ω ±5%) [R112] 141 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R113] 142 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R114] 143 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R115] 144 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R117] 145 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R119] 146 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R120] 147 VRS-TS2AD223J AA C Resistor(1/10W 22KΩ ±5%) [R121] 148 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R122] 149 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R123] 150 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R124] 151 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R125] 152 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R126] 153 VRS-TS2AD512J AA C Resistor(1/10W 5.1KΩ ±5%) [R128] 154 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R129] 155 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R130] 156 VRS-TS2AD105J AA C Resistor(1/10W 1.0MΩ ±5%) [R131] 157 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R132] 158 VRS-TS2AD121J AA C Resistor(1/10W 120Ω ±5%) [R133] 159 VRS-TS2AD222J AA C Resistor(1/10W 2.2KΩ ±5%) [R134]

Page 72

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[7] Control PWB unit

160 VRS-TS2AD333J AA C Resistor(1/10W 33KΩ ±5%) [R135] 161 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R136] 162 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R138] 163 VRS-TS2AD224J AA C Resistor(1/10W 220KΩ ±5%) [R139] 164 VRS-TS2AD153J AA C Resistor(1/10W 15KΩ ±5%) [R140] 165 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R141] 166 VRS-TS2AD303J AA C Resistor(1/10W 30KΩ ±5%) [R142] 167 VRS-TS2AD433J AA C Resistor(1/10W 43KΩ ±5%) [R143] 168 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R144] 169 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R145] 170 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R146] 171 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R148] 172 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R152] 173 VRS-TS2AD334J AA C Resistor(1/10W 330KΩ ±5%) [R153] 174 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R154] 175 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R155] 176 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R156] 177 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R157] 178 VRS-TS2AD512J AA C Resistor(1/10W 5.1KΩ ±5%) [R158] 179 VRS-TS2AD562J AA C Resistor(1/10W 5.6KΩ ±5%) [R160] 180 VRS-TS2AD474J AA C Resistor(1/10W 470KΩ ±5%) [R161] 181 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R162] 182 VRS-TS2AD104J AA C Resistor(1/10W 100KΩ ±5%) [R165] 183 VRS-TS2AD271J AA C Resistor(1/10W 270Ω ±5%) [R167] 184 VRS-TS2AD103J AA C Resistor(1/10W 10KΩ ±5%) [R168] 185 VRS-TS2AD471J AA C Resistor(1/10W 470Ω ±5%) [R169] 186 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R170] 187 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA1] 188 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA2] 189 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA3] 190 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA4] 191 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA5] 192 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA6] 193 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA7] 194 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA8] 195 RR-TZ3017SCZZ AC C Block resistor(270Ωx4) [RA9] 196 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA11] 197 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA12] 198 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA13] 199 RR-TZ3018SCZZ AC C Block resistor(470Ωx4) [RA14] 200 VHI62FP332P-1 AF B IC(XC62FP3302P) [REG100] 201 RRLYD3138XHZZ AG B Relay(DQ24D1) [RY1] 202 RCRSQ2157SCZZ AF N B Crystal(32.256MHz) [X1] 203 RCRSB0297AFZZ AD B Crystal(32.768kHz) [X2]

(Unit)

901 DCEKC689MXHZZ BP N E Control PWB unit(Within ROM) [8]

DCEKC685MXHZZ BP N E Control PWB unit(Within ROM) [40/50] DCEKC780MXHZZ BP N E Control PWB unit(Within ROM) [5]

[8] TEL/Liu PWB unit

1 VHVRA391PV6-1 AE B Varistor(RA-391P-V6-2) [AR1] 2 QCNW-4753XHZZ AE C Cable [ARG] 3 RC-FZ3024SCZZ AG C Capacitor(250WV 0.82µF) [C3] 4 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C5] 5 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C6] 6 VCEAGA1HW106M AA C Capacitor(50WV 10µF) [C7] 7 VCEAGA1HW475M AA C Capacitor(50WV 4.7µF) [C9] 8 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C11]

9 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C12] 10 VCEAGA1HW226M AB C Capacitor(50WV 22µF) [C13] 11 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C104] 12 VCKYTV1HB222K AA C Capacitor(50WV 2200PF) [C105] 13 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C106] 14 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C107] 15 VCKYTV1HB392K AA C Capacitor(50WV 3900PF) [C108] 16 VCKYTV1HB221K AA C Capacitor(50WV 220PF) [C109] 17 VCKYTV1HB221K AA C Capacitor(50WV 2200PF) [C111] 18 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C112] 19 VCKYTV1HB102K AA C Capacitor(50WV 1000PF) [C113] 20 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C114] 21 VCCCTV1HH330J AA C Capacitor(50WV 33PF) [C115] 22 VCKYTV1EF104Z AA C Capacitor(25WV 0.1µF) [C117] 23 VCKYTV1HF104Z AA C Capacitor(50WV 0.1µF) [C118] 24 VCKYTV1HB821K AA C Capacitor(50WV 820PF) [C120] 25 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C122] 26 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C124] 27 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [C127] 28 RRLYZ3433XHZZ AG B Relay [CML1] 29 QJAKZ2079XH0D AD C Jack [CNHJ]

– 9 –

Page 73

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

[8] TEL/Liu PWB unit

30 QCNCM2548SC1B AH C Connector(12pin) [CNLIUA] 31 QJAKZ2060SC0B AD C Jack [CNLNJ] 32 QJAKZ2060SC0B AD C Jack [CNTLJ] 33 VHDDSS133//-1 AA B Diode(1SS133) [D1] 34 VHDDSS133//-1 AA B Diode(1SS133) [D4] 35 QSW-Z2263XHZZ AG B Hook switch [HOOK SW] 36 VHINJM2904M-2 AG B IC(NJM2904M) [IC101] 37 VHINJM2904M-2 AG B IC(NJM2904M) [IC102] 38 RFILN2027XHZZ AC C Coil(R-5C) [L3A] 39 RFILN2027XHZZ AC C Coil(R-5C) [L3B] 40 RFILN2027XHZZ AC C Coil(R-5C) [L6] 41 RFILN2027XHZZ AC C Coil(R-5C) [L7] 42 RFILN2027XHZZ AC C Coil(R-5C) [L8] 43 VHPTLP521-1BL AE B Photo coupler(TLP521) [PC5] 44 VS2SC2412KR-1 AD B Transistor(2SC2412K) [Q101] 45 VSRNC1402//-1 AC B Transistor(RNC1402) [Q104] 46 VSRNC1402//-1 AC B Transistor(RNC1402) [Q107] 47 VRD-HT2HY223J AA C Resistor(1/2W 22KΩ ±5%) [R3] 48 VRS-TS2AD433J AA C Resistor(1/10W 43KΩ ±5%) [R101] 49 VRS-TS2AD152J AA C Resistor(1/10W 1.5KΩ ±5%) [R108] 50 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R109] 51 VRS-TS2AD512J AA C Resistor(1/10W 5.1KΩ ±5%) [R110] 52 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R111] 53 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R112] 54 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R113] 55 VRS-TS2AD433J AA C Resistor(1/10W 43KΩ ±5%) [R114] 56 VRSTS2AD8662F AA C Resistor(1/10W 86.6KΩ ±1%) [R115] 57 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R116] 58 VRS-TS2AD101J AA C Resistor(1/10W 100Ω ±5%) [R118] 59 VRS-TS2AD151J AA C Resistor(1/10W 150Ω ±5%) [R123] 60 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R125] 61 VRS-TS2AD224J AA C Resistor(1/10W 220KΩ ±5%) [R126] 62 VRS-TS2AD683J AA C Resistor(1/10W 68KΩ ±5%) [R127] 63 VRS-TS2AD822J AA C Resistor(1/10W 8.2KΩ ±5%) [R128] 64 VRS-TS2AD621J AA C Resistor(1/10W 620Ω ±5%) [R129] 65 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R130] 66 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R131] 67 VRS-TS2AD000J AA C Resistor(1/10W 0Ω ±5%) [R132] 68 VRS-TS2AD513J AA C Resistor(1/10W 51KΩ ±5%) [R133] 69 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R134] 70 VRS-TS2AD102J AA C Resistor(1/10W 1KΩ ±5%) [R135] 71 VRS-TS2AD203J AA C Resistor(1/10W 20KΩ ±5%) [R140] 72 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R141] 73 VRS-TS2AD332J AA C Resistor(1/10W 3.3KΩ ±5%) [R142] 74 VRS-TS2AD473J AA C Resistor(1/10W 47KΩ ±5%) [R143] 75 VRS-TS2AD472J AA C Resistor(1/10W 4.7KΩ ±5%) [R144] 76 RTRNI2164XHZZ AG B Transformer [T1] 77 VHVERZV5D471/ AC B Varistor(ERZV5D471) [VA1] 78 VHVERZV5D471/ AC B Varistor(ERZV5D471) [VA2] 79 VHEHZ27-1//-1 AB B Zener diode(HZ27) [ZD4]

(Unit)

901 DCEKL483BXH02 AX E TEL/Liu PWB unit

[9] Power supply PWB unit

1 0CBUGFM224KR/ AF C Capacitor(RE224-C) [C1] 2 0CBUGZ1072ZZ/ AN C Capacitor(KMF400VB68M) [C2] 3 0CBUGCV102HZ/ AD C Capacitor(ECKZ3D102KBP) [C3] 4 0CBUGXAEF222/ AC C Capacitor(GRM40B222K50PT) [C4] 5 0CBUEXCAO000/ AB C Resistor(MCR10EZHJ000) [C6] 6 0CBUGCM392BJ/ AF C Capacitor(DE1510-1E392M-KX) [C7] 7 0CBUGAE561TS/ AH C Capacitor(LXJ35VB560(M)) [C8] 8 0CBUGFF474JA/ AF C Capacitor(ECQV1H474JL3) [C9]

9 0CBUGAC222VV/ AK C Capacitor(LXZ16VB2200(K)) [C10] 10 0CBUGXAED104/ AC C Capacitor(GRM40B104K25PT) [C12] 11 0CBUGZ1041ZZ/ AF C Capacitor(DE1007E222M-KH) [C15] 12 0CBUGAB101RV/ AF C Capacitor(KME10VB100(M)) [C16] 13 0CBUGXAEF102/ AC C Capacitor(GRM40B102K50PT) [C17] 14 0CBUGCU681BR/ AC C Capacitor(DEO805R681K1K-MHR) [C21] 15 0CBUGFF223EH/ AC C Capacitor(AMZV-223J50) [C24] 16 0CBPKZ0194ZZ/ AC C Base post ass’y(B 2P3-VH) [CN1] 17 0CBPCZ0275ZZ/ AD C Connector(8PL-FJ) [CN2] 18 0CBUBC0125DK/ AD B Diode(ERA15-06) [D1] 19 0CBUBC0125DK/ AD B Diode(ERA15-06) [D2] 20 0CBUBC0125DK/ AD B Diode(ERA15-06) [D3] 21 0CBUBC0125DK/ AD B Diode(ERA15-06) [D4] 22 0CBUBY0020AK/ AD B Diode(1SS355) [D5]

– 10 –

Page 74

NO.

PARTS CODE

PRICE

RANK

NEW

MARK

PART

RANK

DESCRIPTION

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 11 –

[9] Power supply PWB unit

23 0CBUBC0336AZ/ AL B Diode(S3L20U-4004P15) [D7] 24 0CBUBC0302BZ/ AE B Diode(SR140) [D8] 25 0CBPJCEJ1601/ AH A Current fuse(21501.6 ME600) [F1] 26 0CBPJCEJ1601/ AH A Current fuse(21501.6 ME600) [F2] 27 0CBPZZ0906ZZ/ AH A Circuit protect chip(CCP2E100) [F3] 28 0CBBFZ89256Z/ AD B Beads core(BL02RNI-R62T4) [FB1] 29 0CBUCB0199AZ/ AR B IC(UPC29M05AHF) [IC1] 30 0CBUKZ0826ZZ/ AK C Filter(ELF15N003A) [L1] 31 0CBUZZ0156ZZ/ AN C Coil(RS208) [L2] 32 0CBPZZ0940ZZ/ AB C Jumper(J1/6Z-T26-A) [L3] 33 0CBLRZ6616ZN/ AQ C Heat sink(MN903-5001AT) [MT1] 34 0CBLRZ6619ZQ/ AQ C Heat sink(MF903-5002AT) [MT2] 35 0CBUDC0163CZ/ AG B Photo coupler(PC123YS) [PC1] 36 0CBUDC0163CZ/ AG B Photo coupler(PC123YS) [PC2] 37 0CBUAG0161AC/ AQ B FET(FS5KM-18A-AN) [Q1] 38 0CBUDA0128AK/ AD B Transistor(2SD2114K) [Q2] 39 0CBUAY0016CK/ AD B Transistor(2SC2412K) [Q3] 40 0CBUAY0016CK/ AD B Transistor(2SC2412K) [Q4] 41 0CBUAC0289AK/ AD B Transistor(2SC4210) [Q5] 42 0CBUAC0289AK/ AD B Transistor(2SC4210) [Q6] 43 0CBUEEC335CH/ AC C Resistor(RDM12TB335J) [R1] 44 0CBUEEC105CH/ AC C Resistor(RDM12TB105J) [R2] 45 0CBUEEC105CH/ AC C Resistor(RDM12TB105J) [R3] 46 0CBUEXCAS331/ AB C Resistor(CR21TR331J) [R4] 47 0CBUEXCAS152/ AB C Resistor(CR21TR152J) [R5] 48 0CBUEXCAS183/ AB C Resistor(CR21TR183J) [R6] 49 0CBUEXCAS330/ AB C Resistor(CR21TR330J) [R7] 50 0CBUEXCAS473/ AB C Resistor(CR21TR473J) [R8] 51 0CBUEXCAS471/ AB C Resistor(CR21TR471J) [R9] 52 0CBUEFDR33DB/ AE C Resistor(RSMF1TBR33G) [R10] 53 0CBUEXCAS390/ AB C Resistor(CR21TR390J) [R11] 54 0CBUEXCAS184/ AB C Resistor(CR21TR184J) [R12] 55 0CBUEXCAS472/ AB C Resistor(CR21TR472J) [R13] 56 0CBUEXCAS152/ AB C Resistor(CR21TR152J) [R14] 57 0CBUEXCAS334/ AB C Resistor(CR21TR334J) [R15] 58 0CBUEXCAS223/ AB C Resistor(CR21TR223J) [R16] 59 0CBUEXCAS822/ AB C Resistor(CR21TR822J) [R17] 60 0CBUEXCAS273/ AB C Resistor(CR21TR273J) [R18] 61 0CBUEXCAS472/ AB C Resistor(CR21TR472J) [R19] 62 0CBUEXCAS472/ AB C Resistor(CR21TR472J) [R20] 63 0CBUEXCAS154/ AB C Resistor(CR21TR154J) [R21] 64 0CBUEXCAS103/ AB C Resistor(CR21TR103J) [R25] 65 0CB829655027/ BE B Transformer(PTTP124-KTT) [T1] 66 0CBUDC0232AK/ AF B Thermistor(KL07L8R2TB) [TH1] 67 0CBUEZ0507ZZ/ AD B Varistor(ERZV07D471) [V1] 68 0CBUFBA102FE/ AD B Variable resistor(ENV CYA A01 B13) [VR1] 69 0CBUBDAX270A/ AD B Zener diode(RD27SB) [ZD1] 70 0CBUBXAD2R0A/ AD B Zener diode(RD2.0SB) [ZD2] 71 0CBUBDBM300D/ AC B Zener diode(RD30FB) [ZD4] 72 0CBUBXAD6R2C/ AD B Zener diode(RD6.2SB) [ZD5] 73 0CBUBDBE200D/ AD B Zener diode(RD20ESAB) [ZD7]

(Unit)

901 RDENT2144XHZZ BA E Power supply PWB unit

Page 75

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

No.

NEW MARK

PART

RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART

RANK

PRICE

RANK

PARTS CODE

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 12 –

I n d e x

[C]

CCNW-212AXH01 1-2 AK C

″ 3-1 AK C

CCNW-215AXH01 1-12 AG C

[D]

DCEKC685MXHZZ 1-45 BP N E

″ 7-901 BP N E

DCEKC689MXHZZ 1-45 BP N E

″ 7-901 BP N E

DCEKC780MXHZZ 1-45 BP N E

″ 7-901 BP N E

DCEKL483BXH02 1-16 AX E

″ 8-901 AX E

DCEKP481BXH04 1-1 AP E

″ 3-901 AP E

DCEKP481BXH05 1-1 AP E

″ 3-901 AP E

DCEKP481BXH18 1-1 AP N E

″ 3-901 AP N E

DCEKP481BXH19 1-1 AP N E

″ 3-901 AP N E DCEKP482BXH01 3-7 AQ E DCEKP482BXH02 3-7 AP N E DUNTK468BXHPU 6-2 AH E

[G] GCABA2342XHSA 3-3 AH D GCABA2342XHSB 3-3 AH N D GCABA2342XHSC 3-3 AH D GCABB2343XHSA 1-13 AK D GCABB2343XHSB 1-13 AK N D GCABB2343XHSC 1-13 AK D GCASP2110XHSD 1-17 AK C GCASP2110XHSE 1-17 AK C GCASP2110XHSF 1-17 AK N C GCASP2111XHSA 1-18 AH C GCASP2111XHSB 1-18 AH N C GCASP2111XHSC 1-18 AH N C GDAI-2082XHSD 1-46 AD C GDAI-2083XHZZ 1-22 AF C

[H] HPNLH2392XHSU 1-54 AE N D HPNLH2392XHS3 1-54 AE N D HPNLH2394XHSA 1-54 AE N D HPNLH2394XHSE 1-54 AE N D

[J] JBTN-2257XHSD 3-4 AD C JBTN-2258XHSA 3-5 AC C JBTN-2258XHSB 3-5 AC N C JBTN-2258XHSC 3-5 AC C JBTN-2261XHSA 3-6 AC C JBTN-2261XHSC 3-6 AC C

[L] LBNDJ2006XHZZ 1-55 AA C

″ 2-19 AA C LBSHP2110XHZZ 2-1 AB C LBSHP2112XHZZ 1-28 AB C LFRM-2207XHZZ 5-1 AF N C LFRM-2208XHZZ 1-29 AF C LFRM-2209XHZZ 2-2 AF C LHLDZ2180XHZZ 2-3 AC C LHLDZ2181XHZZ 2-4 AC C LHLDZ2184XHZZ 1-30 AC C LHLDZ2185XHZZ 1-31 AC C LPLTG2911XHZZ 4-1 AE C LPLTM3049XHZZ 5-2 AD C LPLTP2908XHZZ 4-2 AE C LPLTP3051XHZZ 4-3 AB C LPLTP3058XHZZ 4-8 AD N C LSTPP2054XHZZ 1-47 AC C LX-BZ2138XHZZ 1-B1 AB C

[M] MCAMP2027XHZZ 5-4 AC C MLEVP2311XHZZ 5-5 AB C MLEVP2312XHZZ 5-6 AB N C MLEVP2314XHZZ 5-8 AB C MLEVP2316XHZZ 1-23 AC C MLEVP2317XHZZ 2-5 AB C MLEVP2319XHZZ 1-49 AC C MLEVP2320XHZZ 1-19 AC C MLEVP2321XHZZ 1-58 AN N C

MSPRC2735XHZZ 5-9 AC C MSPRC2954XHZZ 1-5 AC C MSPRC3110XHZZ 5-10 AB C MSPRC3112XHZZ 1-33 AC C MSPRC3117XHZZ 2-6 AB C MSPRC3148XHZZ 1-34 AC C MSPRD3116XHZZ 1-24 AB C MSPRP3119XHZZ 1-14 AC C MSPRP3123XHZZ 1-15 AC C MSPRT3139XHZZ 4-5 AA C MSPRT3140XHZZ 4-4 AA C

[N] NGERH2278XHZZ 5-12 AC C NGERH2379XHZZ 5-13 AC C NGERH2391XHZZ 5-15 AC C NGERH2475XHZZ 5-17 AB C NGERH2478XHZZ 1-36 AB C NGERH2479XHZZ 2-7 AB C NGERH2480XHZZ 2-8 AB C NGERH2481XHZZ 2-9 AB C NGERP2318XHZZ 1-6 AD C NROLR2375XHZZ 2-10 AL C NROLR2425XHZZ 1-37 AP C NROLR2428XHZZ 2-11 AP C NSFTZ2273XHZZ 2-12 AF C NSFTZ2320XHZZ 6-18 AF C

[P] PGIDM2554XHZZ 4-6 AF C PGIDM2560XHSD 1-7 AE C PGIDM2561XHSD 1-8 AC C PGIDM2562XHZA 2-13 AD N C PGIDM2562XHZZ 2-13 AD C PGIDM2563XHSA 1-27 AE N C PGIDM2563XHSB 1-27 AE N C PGIDM2563XHSC 1-27 AC N C PGIDM2566XHZZ 1-52 AC C PGIDM2578XHZZ 6-16 AE C PGIDM2579XHZZ 6-17 AE C PHOP-2104XHSD 1-9 AF C PHOP-2105XHZZ 6-4 AD C PSHEZ3410XHZZ 1-56 AB C PSHEZ3436XHZZ 2-14 AC C PSHEZ3517XHZZ 4-7 AE N C

[Q] QACCE2042XHZZ 1-20 AL B QCNCM2401SC0B 7-91 AA C QCNCM2442SC0B 7-84 AB C QCNCM2548SC1B 8-30 AH C QCNCM7014SC0B 7-86 AD C QCNCM7014SC0F 7-88 AB C QCNCM7014SC0G 7-83 AB C QCNCM7014SC1F 7-89 AD C

″ 7-92 AD C QCNCM705BAF06 7-85 AB C QCNCW2500SC0H 7-90 AF C QCNCW2500SC1B 7-87 AF C QCNW-209AXHZZ 1-39 AH C QCNW-210AXHZZ 1-40 AC C QCNW-211AXHZZ 2-15 AF C QCNW-213AXHZZ 2-16 AC C QCNW-3975XHGY 6-5 AG C QCNW-3976XHBG 6-3 AK C QCNW-3976XHOG 6-3 AT C QCNW-3976XHOW 6-3 AK C QCNW-4753XHZZ 8-2 AE C QCNW-4933XHZZ 5-20 AC C QFS-P2010SCZZ 7-99 AD B QJAKZ2060SC0B 8-31 AD C

″ 8-32 AD C QJAKZ2079XH0D 8-29 AD C QSOCZ2051SC32 7-104 AC C QSW-F2224SCZZ 5-21 AE B QSW-M2293XHZZ 2-17 AE B QSW-M2296XHZZ 1-11 AD B QSW-Z2263XHZZ 8-35 AG B

[R] RC-FZ3024SCZZ 8-3 AG C RCILZ2145XHZZ 7-61 AF C

″ 7-64 AF C ″ 7-109 AF C

RCILZ2145XHZZ 7-110 AF C

″ 7-111 AF C ″ 7-112 AF C ″ 7-113 AF C ″ 7-114 AF C ″ 7-115 AF C ″ 7-116 AF C ″ 7-117 AF C ″ 7-118 AF C

RCORF2123XHZZ 2-20 AD B RCORF2125XHZZ 1-53 AE B RCRSB0297AFZZ 7-203 AD B RCRSQ2157SCZZ 7-202 AF N B RDENT2144XHZZ 1-21 BA E

″ 9-901 BA E

RFILN2027XHZZ 8-38 AC C

″ 8-39 AC C ″ 8-40 AC C ″ 8-41 AC C ″ 8-42 AC C

RHEDZ2059XHZZ 1-41 BF B RMOTZ2148XHZZ 5-22 AT B RR-TZ3017SCZZ 7-188 AC C

″ 7-189 AC C ″ 7-192 AC C ″ 7-193 AC C ″ 7-195 AC C

RR-TZ3018SCZZ 7-187 AC C

″ 7-190 AC C ″ 7-191 AC C ″ 7-194 AC C ″ 7-196 AC C ″ 7-197 AC C ″ 7-198 AC C ″ 7-199 AC C

RRLYD3138XHZZ 7-201 AG B RRLYZ3433XHZZ 8-28 AG B RTRNI2164XHZZ 8-76 AG B RUNTZ2054XHZZ 2-18 BE B

[S] SPAKA287BXHZZ 6-7 AE D SPAKA288BXHZZ 6-8 AE D SPAKA289BXHZZ 6-9 AC D SPAKA388BXHZZ 6-21 AE D SPAKA389BXHZZ 6-22 AE D SPAKC178BXHZZ 6-10 AH N D SPAKC187BXHZZ 6-10 AH N D SPAKC189BXHZZ 6-10 AH N D SPAKC194BXHZZ 6-10 AH N D SPAKP296BXHZZ 6-6 AE D

[T] TCADZ2935XHZZ 6-19 AA D TINST4026XHZZ 6-1 AY D TLABM341AXHZZ 6-11 AD N D TLABM344AXHZZ 6-11 AD N D TLABM345AXHZZ 6-11 AD N D TLABM347AXHZZ 6-11 AD N D

[U]

UBATL2046SCZZ 7-1 AK B

[V] VCCCTV1HH120J 7-19 AA C

″ 7-20 AA C

VCCCTV1HH220J 7-33 AA C

″ 7-34 AA C ″ 7-42 AA C ″ 7-43 AA C ″ 7-55 AA C ″ 7-56 AA C ″ 7-58 AA C ″ 7-59 AA C ″ 7-66 AA C

VCCCTV1HH330J 8-21 AA C VCEAGA1EW476M 7-10 AA C

″ 7-11 AA C ″ 7-14 AA C

VCEAGA1HW106M 7-6 AA C

″ 7-8 AA C ″ 7-12 AA C ″ 8-6 AA C

VCEAGA1HW226M 7-13 AB C

Page 76

No.

NEW MARK

PART

RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART

RANK

PRICE

RANK

PARTS CODE

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 13 –

VCEAGA1HW226M 8-4 AB C

″ 8-5 AB C ″ 8-8 AB C ″ 8-9 AB C ″ 8-10 AB C

VCEAGA1HW475M 8-7 AA C VCKYTV1CF105Z 7-17 AB C

″ 7-21 AB C ″ 7-24 AB C ″ 7-29 AB C ″ 7-30 AB C ″ 7-32 AB C ″ 7-38 AB C ″ 7-39 AB C ″ 7-40 AB C ″ 7-41 AB C ″ 7-44 AB C ″ 7-49 AB C ″ 7-50 AB C ″ 7-51 AB C ″ 7-53 AB C ″ 7-57 AB C ″ 7-62 AB C ″ 7-63 AB C ″ 7-65 AB C ″ 7-71 AB C ″ 7-76 AB C ″ 7-77 AB C

VCKYTV1EB104K 7-47 AA C

″ 7-68 AA C

VCKYTV1EF104Z 7-4 AA C

″ 7-7 AA C ″ 7-28 AA C ″ 7-31 AA C ″ 7-35 AA C ″ 7-37 AA C ″ 7-46 AA C ″ 7-48 AA C ″ 7-54 AA C ″ 7-74 AA C ″ 7-78 AA C ″ 7-80 AA C ″ 8-13 AA C ″ 8-22 AA C

VCKYTV1HB102K 7-2 AA C

″ 7-3 AA C ″ 7-15 AA C ″ 7-16 AA C ″ 7-22 AA C ″ 7-23 AA C ″ 7-25 AA C ″ 7-45 AA C ″ 7-81 AA C ″ 7-82 AA C ″ 8-14 AA C ″ 8-19 AA C

VCKYTV1HB103K 7-5 AB C

″ 7-73 AB C

VCKYTV1HB221K 7-72 AA C

″ 8-16 AA C ″ 8-17 AA C

VCKYTV1HB222K 7-26 AA C

″ 7-27 AA C ″ 7-36 AA C ″ 7-52 AA C ″ 7-60 AA C ″ 8-11 AA C ″ 8-12 AA C

VCKYTV1HB392K 8-15 AA C VCKYTV1HB472K 7-75 AA C VCKYTV1HB821K 8-24 AA C VCKYTV1HF104Z 7-18 AA C

″ 7-79 AA C ″ 8-18 AA C ″ 8-20 AA C ″ 8-23 AA C

VHDDSS133//-1 8-33 AA B

″ 8-34 AA B VHDHRW0202B-1 7-97 AD B VHD1SS355//-1 7-94 AB B

VHD1SS355//-1 7-95 AB B

″ 7-96 AB B ″ 7-98 AB B

VHEHZ27-1//-1 8-79 AB B VHIFC2FM209-1 7-101 BD B

″ 7-103 BD B VHINJM2113M-1 7-106 AG B VHINJM2904M-2 8-36 AG B

″ 8-37 AG B VHITC7WT74FU1 7-100 AF B VHIULN2003AN/ 7-107 AE B VHIW24258S7LE 7-102 AQ B VHIXC61AN45M1 7-108 AE B VHI27010FZJ0B 7-104 BM N B VHI27010FZK0A 7-104 BM N B VHI62FP332P-1 7-200 AF B VHPSG206S//-1 7-119 AG B VHPTLP521-1BL 8-43 AE B VHVERZV5D471/ 8-77 AC B

″ 8-78 AC B VHVRA391PV6-1 8-1 AE B VRD-HT2HY223J 8-47 AA C VRS-HT3AA101J 7-93 AA C VRS-TS2AD000J 7-9 AA C

″ 7-67 AA C

″ 7-69 AA C

″ 7-70 AA C

″ 7-127 AA C

″ 7-129 AA C

″ 7-142 AA C

″ 7-155 AA C

″ 7-161 AA C

″ 7-162 AA C

″ 7-170 AA C

″ 7-171 AA C

″ 7-172 AA C

″ 7-186 AA C

″ 8-25 AA C

″ 8-26 AA C

″ 8-27 AA C

″ 8-53 AA C

″ 8-65 AA C

″ 8-67 AA C

VRS-TS2AD101J 8-58 AA C VRS-TS2AD102J 7-154 AA C

″ 7-169 AA C

″ 7-176 AA C

″ 8-50 AA C

″ 8-70 AA C

VRS-TS2AD103J 7-124 AA C

″ 7-148 AA C

″ 7-157 AA C

″ 7-168 AA C

″ 7-184 AA C

VRS-TS2AD104J 7-174 AA C

″ 7-175 AA C

″ 7-182 AA C

VRS-TS2AD105J 7-156 AA C VRS-TS2AD106J 7-125 AA C VRS-TS2AD121J 7-158 AA C VRS-TS2AD151J 7-137 AA C

″ 8-59 AA C VRS-TS2AD152J 8-49 AA C VRS-TS2AD153J 7-164 AA C VRS-TS2AD201J 7-128 AG C

″ 7-140 AG C VRS-TS2AD203J 7-165 AA C

″ 7-177 AA C

″ 7-181 AA C

″ 8-52 AA C

″ 8-54 AA C

″ 8-69 AA C

″ 8-71 AA C

VRS-TS2AD222J 7-159 AA C VRS-TS2AD223J 7-136 AA C

″ 7-147 AA C VRS-TS2AD224J 7-163 AA C

″ 8-61 AA C VRS-TS2AD271J 7-122 AA C

″ 7-132 AA C

VRS-TS2AD271J 7-183 AA C VRS-TS2AD3R0J 7-126 AA C VRS-TS2AD303J 7-166 AA C VRS-TS2AD332J 8-57 AA C

″ 8-60 AA C ″ 8-66 AA C ″ 8-73 AA C

VRS-TS2AD333J 7-123 AA C

″ 7-133 AA C ″ 7-134 AA C ″ 7-135 AA C ″ 7-139 AA C ″ 7-141 AA C ″ 7-145 AA C ″ 7-146 AA C ″ 7-149 AA C ″ 7-150 AA C ″ 7-151 AA C ″ 7-152 AA C ″ 7-160 AA C

VRS-TS2AD334J 7-173 AA C VRS-TS2AD433J 7-167 AA C

″ 8-48 AA C ″ 8-55 AA C

VRS-TS2AD471J 7-130 AA C

″ 7-131 AA C ″ 7-138 AA C ″ 7-143 AA C ″ 7-144 AA C ″ 7-185 AA C

VRS-TS2AD472J 8-75 AA C VRS-TS2AD473J 8-72 AA C

″ 8-74 AA C VRS-TS2AD474J 7-180 AA C VRS-TS2AD512J 7-153 AA C

″ 7-178 AA C

″ 8-51 AA C

VRS-TS2AD513J 8-68 AA C VRS-TS2AD562J 7-179 AA C VRS-TS2AD621J 8-64 AA C VRS-TS2AD683J 8-62 AA C VRS-TS2AD822J 8-63 AA C VRSTS2AD8662F 8-56 AA C VSRNC1402//-1 8-45 AC B

″ 8-46 AC B VS2SA1037KS-1 7-120 AB B

″ 7-121 AB B VS2SC2412KR-1 8-44 AD B

[X] XBBSD30P06000 1-B4 AA C XBPSN40P06K00 1-B5 AA C XEBSD30P08000 1-B3 AA C

″ 5-B3 AA C XEBSD30P12000 1-B7 AA C XUBSD20P06000 3-B2 AA C

[0] 0CBBFZ89256Z/ 9-28 AD B 0CBLRZ6616ZN/ 9-33 AQ C 0CBLRZ6619ZQ/ 9-34 AQ C 0CBPCZ0275ZZ/ 9-17 AD C 0CBPJCEJ1601/ 9-25 AH A

″ 9-26 AH A 0CBPKZ0194ZZ/ 9-16 AC C 0CBPZZ0906ZZ/ 9-27 AH A 0CBPZZ0940ZZ/ 9-32 AB C 0CBUAC0289AK/ 9-41 AD B

″ 9-42 AD B 0CBUAG0161AC/ 9-37 AQ B 0CBUAY0016CK/ 9-39 AD B

″ 9-40 AD B 0CBUBC0125DK/ 9-18 AD B

″ 9-19 AD B

″ 9-20 AD B

″ 9-21 AD B

0CBUBC0302BZ/ 9-24 AE B 0CBUBC0336AZ/ 9-23 AL B 0CBUBDAX270A/ 9-69 AD B 0CBUBDBE200D/ 9-73 AD B 0CBUBDBM300D/ 9-71 AC B 0CBUBXAD2R0A/ 9-70 AD B

Page 77

No.

NEW

MARK

PART RANK

PRICE

RANK

PARTS CODE

No.

NEW MARK

PART

RANK

PRICE

RANK

PARTS CODE

No.

NEW

MARK

PART

RANK

PRICE

RANK

PARTS CODE

UX-8TH/UX-40TH GQ-5TH/FO-50TH

– 14 –

0CBUBXAD6R2C/ 9-72 AD B 0CBUBY0020AK/ 9-22 AD B 0CBUCB0199AZ/ 9-29 AR B 0CBUDA0128AK/ 9-38 AD B 0CBUDC0163CZ/ 9-35 AG B

″ 9-36 AG B 0CBUDC0232AK/ 9-66 AF B 0CBUEEC105CH/ 9-44 AC C

″ 9-45 AC C 0CBUEEC335CH/ 9-43 AC C 0CBUEFDR33DB/ 9-52 AE C 0CBUEXCAO000/ 9-5 AB C 0CBUEXCAS103/ 9-64 AB C 0CBUEXCAS152/ 9-47 AB C

″ 9-56 AB C 0CBUEXCAS154/ 9-63 AB C 0CBUEXCAS183/ 9-48 AB C 0CBUEXCAS184/ 9-54 AB C 0CBUEXCAS223/ 9-58 AB C 0CBUEXCAS273/ 9-60 AB C 0CBUEXCAS330/ 9-49 AB C 0CBUEXCAS331/ 9-46 AB C 0CBUEXCAS334/ 9-57 AB C 0CBUEXCAS390/ 9-53 AB C 0CBUEXCAS471/ 9-51 AB C 0CBUEXCAS472/ 9-55 AB C

″ 9-61 AB C

″ 9-62 AB C

0CBUEXCAS473/ 9-50 AB C 0CBUEXCAS822/ 9-59 AB C 0CBUEZ0507ZZ/ 9-67 AD B 0CBUFBA102FE/ 9-68 AD B 0CBUGAB101RV/ 9-12 AF C 0CBUGAC222VV/ 9-9 AK C 0CBUGAE561TS/ 9-7 AH C 0CBUGCM392BJ/ 9-6 AF C 0CBUGCU681BR/ 9-14 AC C 0CBUGCV102HZ/ 9-3 AD C 0CBUGFF223EH/ 9-15 AC C 0CBUGFF474JA/ 9-8 AF C 0CBUGFM224KR/ 9-1 AF C 0CBUGXAED104/ 9-10 AC C 0CBUGXAEF102/ 9-13 AC C 0CBUGXAEF222/ 9-4 AC C 0CBUGZ1041ZZ/ 9-11 AF C 0CBUGZ1072ZZ/ 9-2 AN C 0CBUKZ0826ZZ/ 9-30 AK C 0CBUZZ0156ZZ/ 9-31 AN C 0CB829655027/ 9-65 BE B

Page 78

UX-8TH/UX-40TH GQ-5TH/FO-50TH

SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan

Printed in Japan

9911-37NS•IS•T

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.