Sharp GL5ZJ43 Datasheet

PREPARED BY:

r- uQ.ds.

APPROVED BY: DATE: ELECTROMC COMPONENTS GROUP REPRESENTATIVE DIVISION:

< un

J-

.T qKJ7~s-e

DATE:

suln/tO/?q

lik e5 SHARP CORPORATION

SPECIFICATION

DEVICE SPECIFICATION FOR

SPECNo. DG996036
ISSUE
PAGE

Opto-Electronic Devices Division

J&16/99

10

pages

Light Emitting Diode

MODEL No.

1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharps consent.

2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.

(Precautions)

(1) This products is designed for use in the following application areas;

* OA equipment * Audio visual equipment
* Telecommunication equipment (Terminal)

* Tooling machines * Computers

L

If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions given in those respective paragraphs.

(2) Appropriate measures, such as fail-safe design and redundant design considering

the safety design of the overall system and equipment, should be taken to ensure reliability

. and safety when this product is used for equipment which demands high reliability and

safety in function and precision, such as ;

* Transportanon control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals * Gas leakage sensor breakers * Rescue and security equipment
* Other safety equipment

[

(3) Please do not use this product for equipment which require extremely high reliability

and safety in function and precision, such as ;

* Space equipment * Telecommunication equipment (for trunk lines)
* Nuclear power control equipment * Medical equipment

I

(4) Please contact and consult with a Sharp sales representative if there are any questions

regarding interpretation of the above three paragraphs.

3. Please contact and consult with a Sharp sales representative for any questions about this product.

CUSTOMERS APPROVAL

* Home appliance

* Measuring equipment

DATE:
PRESENTED BY:

I

I

1

DATE:

BY:

M.Katoh,
Department General LManager of
Engineering Dept.,III
Opto-Electronic Devices Division
Electronic Components Group
SHARP CORPOluTION

I

MODEL No. PAGE

GLSZr43 Sneeification

1. Application
This specifkation applies to the light emitting diode device Model No. GL5Z43.

[AlGaInP (dicing or scrilxylxake type> Grange LED device]

DG996036

GL5ZJ43 l/10

Jun/16/99

2. Outline dimensions and pin connections

3. Ratings and characteristics
3-l. Absolute maximum ratings

3-2. Electra-optical characteristics
3-3. Derating Curve
3-4. Characteristics Diagram

4. Reliability
4- 1. Test items and test conditions
4-2. Measurement items and Failure judgement criteria

5. Incoming inspection
5- 1. Applied standard

5-2. Sampling method and level
5-3. Test items, judgement criteria and classilica of defect
5-4. Test items the surface is be applied for flat type, judgement criteria and classilica of defect

. . . . . . . . . . ..*..........................................

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Refer to the attached sheet Page 2.

Refer to the attached sheet Page 3-4.

Refer to the attached sheet Page 5.

Refer to the attached sheet Page 6.

6. Supplement
6-l. Packing
6-2. Luminous intensity rank

6-3. Dominant wavelength rank

64. Environment

7. Precautions for use
7- 1. Lead forming method
7-2. Notice of installation

7-3. Soldering Conditions

.74. For cleaning

. . . . . . ..*..................*..........................

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Refer to the attached sheet Page 7-8.

Refer to the attached sheet Page 9- 10.

2. outline dimensions aad pin

co~ections

Colorless transparency

\

Pin COMectiOns

0. Anode

0. cathode

rote) Unspecif!ed tol. to be ~0.2mm

rote) Cold rolled steel leads are plated with but the tie-bar cut portions have no plating do not solder this part of the product.

. .

unit

Material

Finish

Drawing No.

Lead : (Fe) Cold rolled steel

mm

Package : Epoxy resin

Lead : Sn plated or wave soldering

51106017

MODEL No.

DG996036

Jun/16/%

PAGE

3.

Ratings and characteristics

(Note 1) Duty ratio=l/lO,Pulse width=Qlms
(Note 2) At the position of 1.6mm from the bottom resin package

GL5ZJ43

3/10

(Note 3) Refer to the suplement item 6. regarding the standard of rank classification.

3-3. Derating Curve

Peak Forward Current Derating Curve

120

a

s

e 100

­g 80

z

2 60

-0
5 40

2

,” 20

m

d

0’ ’

-25 0 25 50 75 ‘?iO 125
Ambient Temperature Ta(W Ambient Temperature Ta (%I

I I

I

Forward Current Derating Curve

60

-25 0 25 50 7585

100 125