Sharp GL3ED8 Datasheet

Dichromatic LED Lamp

23.0MIN

(2.0)

3

NOM

2.0

12

Protruded resin 1.0MAX

ø3.8

Milky diffusion

ø3.0

2.0
NOM

(4.0)

4.4

5.0

0.5

±0.1

1.0

±0.5

0.5

±0.1

Pin connections
1 Anode(Yellow-green)
2 Cathode(Common)
3 Anode(Red)

Unspecified tolerance:±0.2

0˚

80

100

40

20

0

60

Yellow-green

-20˚ -10˚-30˚ +20˚ +30˚+10˚

+40˚

+60˚

+80˚

+90˚

+70˚

+50˚

-40˚

-60˚

-80˚

-90˚

-70˚

-50˚

Red

Relative luminous intensity(%)

Milky

diffusion

GL3ED8

Yellow-green
Red

TYP

2.1

MAX

2.8 565 20 20 20 30 20 10 4 35 1

→

2.0 2.8 635 20 15 20 35 20 10 4 20 1

→

Model No.

Lens

type

Forward voltage

VF(V)

λp(nm)

TYP

I

V(mcd)

TYP

I

F

(mA)

IF

(mA)

IF

(mA)

(MH

Z)

V

R

(V)

I

R(µA)

MAX

C

t(pF)

TYP

∆λ(nm)

TYP

Peak emission wavelength

Luminous intensity

Spectrum radiation bandwidth

Reverse current

Page for

characteristics

diagrams

Terminal capacitance

(Ta=25˚C)

Radiation

color

GL3ED8

GL3ED8

ø3mm(T-1), Cylinder Type, Milky
Diffusion, Dichromatic LED Lamp
for Backlight/Indicator

■ Outline Dimensions

(Unit : mm) (Ta=25˚C)

■ Radiation Diagram

■ Absolute Maximum Ratings

Power dissipation

Model No.

GL3ED8

*1 The value is specified under the condition that either color is lightened separately. When the both diodes are lightened simultaneously,
the power dissipation of each diode should be less than the half of the value specified in this table.
*2 Duty ratio=1/10, Pulse width=0.1ms

Radiation color

Yellow-green
Red

Radiation material

GaP
GaAsP on GaP

*1

P

(mW)

84
84

Forward current

Peak forward current

IF

(mA)

30
30

IFM

(mA)

50
50

*3 5s or less(At the position of 1.6mm or more from the bottom face of resin package)

■ Electro-optical Characteristics

(Notice) ¡
(Internet) ¡Data for sharp's optoelectronic/power device is provided for internet.(Address http://www.sharp.co.jp/ecg/)

In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP
devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.

*2

Derating factor

(mA/˚C)

DC

0.40

0.40

Reverse voltage

Pulse

0.67

0.67

Operating temperature

VR

(V)

5
5

Topr

(˚C)

-25 to +85 -25 to +100

Storage temperature

Tstg

(˚C)

(T

a=25˚C)

Soldering temperature

Tsol

(˚C)

260

*3

EG series

0

10

20

30

40

50

60

-25 0 25 50 75 85 125100

Peak Forward Current Derating Curve

Ambient temperature Ta(˚C)

Peak forward current IFM(mA)

0

10

20

30

40

50

60

-25 0 25 50 75 85 125100

Forward Current Derating Curve

Ambient temperature Ta(˚C)

Forward current IF(mA)

0.1

0.5

1.0

5.0

10

50

100

1.0 1.2 1.4 1.6 1.8 2.0 2.4 2.62.2

Forward Current vs. Forward Voltage(Note)

Forward voltage VF(V)

Forward current IF(mA)

(Ta=25˚C)

1.0

5.0

10

50

100

500

1000

-20 0 20 40 60 80 120100

Luminous Intensity vs. Ambient Temperature(Note)

Ambient temperature Ta(˚C)

Relative luminous intensity(%)

(Ta=25˚C)

1.0

5.0

2.0

10

20

50

100

200

500

1000

0.1 0.2 0.5 1 2 5 10 20 50

Luminous Intensity vs. Forward Current(Note)

Forward current IF(mA)

Relative luminous intensity(%)

(Ta=25˚C)

1.0

5.0

2.0

10

20

50

100

200

500

1/50 1/20 1/10 1/5 1/2 1

Duty Ratio vs. Peak Forward Current

Duty ratio DR

Peak forward current IFM(mA)

(Ta=25˚C)

Note)Characteristics shown in diagrams are typical values. (not assurance value)