SHARP DTE173 Technical Report
Date: Jul. 11, 1994
DUPLICATOR: SD-2060
1. PREVENTION OF THE OUTS ON THE REAR END OF HALF TO NE AND THE COPY
MISALIGNMENT
2. CHANGES TO THE HORIZONTAL PINS (THIS WAS MADE TO IMPROVE
PRODUCTIVITY.)
3. DISCONTINUANCE OF THE END MILL OF THE FUSING DRIVE JOINT SHAFT
(THIS WAS MADE TO IMPROVE PRODUCTIVITY.)
No. : DTE-173
1. Prevention of the outs on the rear end of half tone and the copy misalignment
1.Model name: SD-2060, 3062
2.General: To get higher precision in function and to prevent both the outs on the rear end of half
tone, of back side copies and the copy misalignment, we minimized the shaft hall
internal diameter of two kinds of pulleys used in each drive unit.
3.Description: <Affected units>
1) The drive pulleys of the multi drive unit and the main motor unit (32T)
2) The drive pulleys of the fusing drive unit, the paper feeding drive unit and the main
motor unit (38T)
4.Action: SD-3062 : From the first unit of November 1993 production
SD-2060 : From the first unit of December 1993 production.
2. Changes to the horizontal pins (This was made to improve productivity.)
1.Model name: SD-2060, 3062
2.General: We changed materials and finish of the horizontal pins (φ3 X 20) used in following drive
units to improve productivity.
3.Description: <Affected units>
The multi drive unit The paper feeding drive unit The fusing drive unit
4.Action: From the first unit of April 1994 production.
SHARP CORPORATION Reprography Division
1/2
Green
C
3. Discontinuance of the end mill of the fusing drive joint shaft (This was made to
improve productivity.)
1.Model name: SD-2060, 3062
2.General: We discontnued a useless end mill of the joint shaft used in the fusing drive unit to
improve productivity.
3.Description:
The joint shaft
Discontnue a useless end mill
4.Action: From April 1994 (running change).
Ref.
Model
No.
SD-2060
SD-3062
1
SD-2060
SD-3062
SD-2060
2
SD-3062
SD-2060
3
SD-3062
<Interchange>
1. Interc ha ng ea bl e. 4. N ot i nt er ch an ge ab l e.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
spec ifi e d on es fo r m ai n ta ini ng t he s a fe ty an d pe r fo rma nc e o f the set .
name
Version P/G No.
26 -28
27 -25
23 22
25 -16
All
27 -8
26 -6
25 -8
23 -4
23 -16 NSFTZ1881FCZZ NSFTZ1881FCZ1 AS
!
Current parts New parts
Parts code Parts code
NPLYZ0285FCZZ NPLYZ0285FCZ1 AE
NPLYZ0278FCZZ NPLYZ0278FCZ1 AD
LPINS0276FCZZ
(Q’ty: 2)
LPINS0276FCZZ
(Q’ty: 1)
LPINS0292FCZZ
(Q’ty: 2)
LPINS0292FCZZ
(Q’ty: 1)
Price
rank
AB Pin (φ3x20)
AB Pin (φ3x20)
5. Interchangeable if replaced with same types of
relate d parts in use .
6. Others.
Parts name
Transport drive
pulley 23T
Paper feeding
drive pulley 32T
Fusing drive jont
shaft
Effec-
tive
time
1st lot
’93/12
1st lot
’93/11
1st lot
’93/12
1st lot
’93/11
1st lot
’94/4
1st lot
’94/4
See
text
Inter-
change-
ability
3
3
1
1
1
Note
2/2
Loading...