Date: Jun. 24, 1994
DUPLICATOR : SD-2060
1. DISCONTINUANCE OF PAPER TRAY SPACER INSIDE OF CENTER TRAY UNIT
(TO INCREASE PRODUCTIVITY)
2. IMPROVEMENT OF SCREW INSIDE OF CENTER TRAY UNIT TO PREVENT IT LOOSE
3. DISCONTINUANCE OF SUCTION SEAL INSIDE OF CENTER TRAY UNIT
4. CHANGES TO FINISHER UNIT AND ELEVATOR DRIVE GEAR (TO INCREASE
PRODUCTIVITY)
1. Discontinuance of paper tray spacer inside of center tray unit
(To increase productivity)
1.Model name: SD-2060, 3062
No. : DTE-164
2.General: We mounted paper tray spacer B and C to hollows in paper tray inside of center tray
unit. In order to increase productivity, we change paper tray by using metal mold.
3.Description: We change the forms of paper tray by using metal mold. After change is carried out, we
discontinue paper tray spacer B and C in paper tray.
4.Action: From May 1994 production.
2. Improvement of screw inside of center tray unit to prevent it loose
1.Model name: SD-2060, 3062
2.General: We found that screw in center tray unit clamped insufficiently and became loose
therefore we change screw.
3.Description:
13
Change to LX-BZ0293FCZZ
13
7
Change to XEBSD40P10000
SHARP CORPORATION Reprography Division
1/4
Green
C
4.Action: From the first unit of May 1994 production.
3. Discontinuance of suction seal inside of center tray unit
1.Model name: SD-2060, 3062
2.General: We examined indispensability of suction seal A and B which had dealt with ozone and
confirmed that there is no effect on ozone. Therefore we eliminate suction seal.
3.Action: From the first unit of May 1994 production.
4. Changes to finisher unit and elevator drive gear (T o increase productivity)
1.Model name: SD-3062
2.General: Part of elevator drive section in finisher unit has been changed in order to increase
productivity.
3.Description:
Parts name P/G No. Difference between Current parts and New parts
51 -20
51 -11
51 -19
51 -28
Q'ty: 3 to 0
Gear width Broad → Narrow (Refer to Figure 1)
Horizontal pins halls 3 → 2
Horizontal pins halls 3 → 2 Add E ring groove
Horizontal pins halls 3 → 2 Add E ring groove
Elevator shaft A
NSFTZ1952FCZ1
Q'ty: 0 to 1
DR drive gear
NGERH0262FCZ1
Q'ty: 0 to 3
Elevator shaft A
Q'ty: 1 to 0
NSFTZ1952FCZZ
Drive shaft A
Gear (25T)
Elevator drive
shaft A
Idle shaft FIN
Elevator shaft A
(Current) (New)
2.5T Gear
NGERH0051FCZZ
2/4
NSFTZ1950FCZZ
Q'ty: 1 to 0
Idle shaft FIN
NSFTZ1999FCZZ
Q'ty: 1 to 0
Idle shaft FIN Q'ty: 0 to 1
NSFTZ1999FCZ1
Elevator drive shaft A
NSFTZ1950FCZ1
Apply (about 5g) to three spots in DR Drive Gear
Q'ty: 0 to 1
4.Action: From the first unit of May 1994 production.
Discontinued one of
horizontal pins
Add E ring groove
Discontinued one of horizontal pins
Discontinued one of horizontal pins
3/4
Ref.
No.
Model
name
Version P/G No.
Current parts New parts
Parts code Parts code
Price
rank
Parts name
Effec-
tive
time
Inter-
change-
ability
Note
1
SD-2060
SD-3062
2
3
4 SD-3062
29 -53
29 -67 PSPAZ0634FCZZ
29 -68 PSPAZ0635FCZZ
29 -13 LX-BZ0465FCZZ
29 -13 — LX-BZ0293FCZZ AA Screw 3
29 -7 XEBSD40P08000
29 -7 — XEBSD40P10000 AA Screw 3 Q’ty: 1
All
30 -20 PSEL-0550FCZZ
30 -21 PSEL-0551FCZZ
51 -20 NGERH0051FCZZ NGERH0262FCZ1 AL
51 -11 NSFTZ1950FCZZ NSFTZ1950FCZ1 AK
51 -19 NSFTZ1999FCZZ NSFTZ1999FCZ1 AH Idle shaft 5
51 -28 NSFTZ1952FCZZ NSFTZ1952FCZ1 AP Elevator shaft A 5
LSOU-0109FCZZ LSOU-0109FCZ1 BC Paper tray
Discontinued
(Q’ty: 2)
Discontinued
(Q’ty: 2)
Q’ty change
(Q’ty: 6 to 4)
Q’ty change
(Q’ty: 11 to 10)
Discontinued
(Q’ty: 2)
Discontinued
(Q’ty: 2)
Paper tray
—
spacer B
Paper tray
—
spacer C
AA Screw —
AA Screw —
— Suction seal A —
— Suction seal B —
C16DR drive
gear
Elevator drive
shaft
’94/5
3
—
—
New part
(Q’ty: 2)
5 Q’ty: 3
5
51 -8 XRESP70-08000
51 -18 LPINS0155FCZZ
<Interchange>
1. Intercha ng ea bl e. 4. N ot i nt er ch an ge ab l e.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
s p ec ifi e d on es fo r m aintaini ng t he s a fe ty an d pe r fo rma nc e o f th e set.
!
Q’ty change
(8 to 9)
Q’ty change
(6 to 3)
AA E ring 5
AA Pin 5
5. Interchangeable if replaced with same types of
relate d parts in use .
6. Others .
4/4
Loading...