SHARP DTE123 Technical Report

Date: Feb. 8, 1994
DUPLICATOR: SD-2060
No. : DTE-123
CHANGE IN PARTS TO IMPROVE PRODUCTIVITY.
1.General: The parts changes described below have been carried out to improve productivity and
operationabilty.
2.Description: 1. A change has been carried out in the maker for ball bearing used in the center tray unit and the drum drive unit, to improve productivity. Ball bearing :
NBRGY0103FCZZ NBRGY0434FCZZ Q’ty: Drum unit: 1
* The old ball bearings are currently being used in the switch back area.
(Factory action)
From 1994 February production.
2. A change in the shape of the spent toner holder inside the spent toner case has been carried out to improve operationability. When assembled in the production process, the thin area of the spent toner holder is sometimes damaged, and therefore a change in shape has been carried out to reinforce the plate and eliminate burrs from the round sections.
Reinforced
Change
Old
Old
The parts codes have not been changed.
New
Eliminate burrs
(Factory action)
From 1993 Mid-October production.
SHARP CORPORATION Reprography Division
1/3
Green
C
3. The screws in the toner box unit have been changed to improve productivity.
,
The attachment screws in the toner hopper base plate and the cartridge guide have been changed.
LX-BZ0560FCZZ LX-BZ0183FCZZ Q’ty: 8 (M4 x 10 cup screw) (M4 x 10 TP screw)
(Factory action)
From 1994 February production.
4. Change in the shape of the pressure plate pushing down on the glass table to establish compatibility . The glass table pressure plate has been changed to establish parts compatibility with a new product (SD-3062).
* The paper flow direction of the original document in model SD-3062 is opposite that
in model SD-2060. As a result, the glass table pressure plate sometimes extend up past the glass table due to the curve or the attachment condition of the plate. This can cause paper jams. The glass table pressure plate has therefore been cut
1.5mm.
This portion has been cut and shortened by 1.5mm to
Glass table.
prevent it from extending up past the glass table.
Glass table pressure plate.
Glass table pressure plate: LFIX-0451FCZZ LFIX- 0451FCZ1
The changed parts can be used in both old and new versions of model SD-2060, and in the new version only of model SD-3062.
(Factory action)
From 1993 Mid-December production (for model SD-2060). From the first production (for model SD-3062).
2/3
Ref.
No.
Model
name
Version P/G No.
Current parts New parts
Parts code Parts code
Price
rank
Parts name
Effec-
tive
time
Inter-
change-
ability
Note
1
SD-2060
3062
2
SD -2060
3
SD -3062
SD -2060
4
SD -3062 1st lot. 3
<Interchange>
1. Interchangea bl e. 4. N ot i nt er ch an ge ab l e.
2. Current type can be used in place of new type. New type cannot be used in place of current type.
3. Current type cannot be used in place of new type. New type can be used in place of current type.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
specified on es fo r m aintaini ng t he s a fe ty and pe r fo r ma nce of the s et .
28 -29
30 -2
33 -11 LHLDZ1123FCZZ No change
All
12 -5
13 -5
1 -20 LFIX-0451FCZZ LFIX-0451FCZ1 AN
!
NBRGY0103FCZZ NBRGY0434FCZZ AN Ball bearings ’94/2 1 Q’ty: 3
LX-BZ0560FCZZ LX-BZ0183FCZZ AA
Waste toner holder
Screws (M x 10 TP)
Glass table pressure plate
5. Interchangeable if replaced with same types of relate d parts in use .
6. Others .
Mid ­Oct. 1993
’94/2 1 Q’ty: 8
Mid-
Dec.
1993
1
3/3
Loading...