Sharp DT-510 User Manual
DT-510
ENGLISH FRANÇAIS
PROJECTOR
PROJECTEUR
PROYECTOR
PROJETOR
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
ESPAÑOL PORTUGUÊS
Before using the projector, please read this operation manual carefully.
Introduction
IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record
the Serial Number located on the bottom
of the projector and retain this information.
• Before recycling the packaging, please
ensure that you have checked the contents of the carton thoroughly against the
list of “Supplied accessories” on page 10.
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
Model No.: DT-510
Serial No.:
ENGLISH
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
U.S.A. ONLY
1
WARNING:
The cooling fan in this projector continues to run for about 90 seconds after the projector enters
standby mode. During normal operation, when putting the projector into standby mode always
use the STANDBY/ON button on the projector or the STANDBY button on the remote control.
Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING
THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the operation manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL DT-510
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 56.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 921,600 pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
2
How to Read this Operation Manual
■ The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
• In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
Using the Menu Screen
ENTER button
Adjustment buttons (P/R/O/Q)
MENU button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
Press dMENU.
1
• The “Picture” menu screen for the selected input mode is displayed.
Press Q or O to select the menu
2
icon to adjust.
• The selected icon is highlighted.
Menu icon Menu screen
Note
• The “Fine Sync” menu is not available
for INPUT 3 or INPUT 4.
Picture
Fine Sync
Options1
Options2
Example: “Picture” screen menu for INPUT 1
mode
Picture INPUT 1
Picture Mode
Contrast 0
Bright
Color
Tint
Sharp
Red
Blue
SEL./ADJ.
RETURN
Adjustment buttons
(P/R/O/Q)
• Press eRETURN to re-
turn to the previous
screen when the menu
is displayed.
Selected input mode
Menu icons
0
0
0
0
0
0
ENTER
END
MENU button
ENTER button
RETURN button
Standard
Features
41
Buttons used in
this operation
Button used in
this step
Useful
On-screen
display
Introduction
Info
........Indicates safeguards for using the projector.
.........Indicates additional information for setting up and operating the
Note
projector.
For Future Reference
PP. 61 and 62
IndexMaintenance Troubleshooting
P. 65P. 51
3
Contents
Preparing
Introduction
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
Accessories ........................................ 10
Part Names and Functions ................. 11
Inserting the Batteries .......................... 14
Usable Range ...................................... 15
Quick Start
Quick Start .......................................... 16
Using
Basic Operation
Turning the Projector On/Off .............. 28
Connecting the Power Cord ................ 28
Turning the Projector on ....................... 28
Turning the Power off (Putting the
Projector into Standby Mode) ........... 29
Image Projection ................................. 29
Switching the Input Mode .................... 29
Adjusting the Projected Image ............ 30
Correcting Trapezoidal Distortion ........ 32
Resize Mode ......................................... 36
Useful Features
Operating with the Remote Control .... 38
Selecting the Picture Mode .................. 38
Switching the Iris Setting ..................... 38
Freezing a Moving Image .................... 38
Menu Items ......................................... 39
Using the Menu Screen ...................... 41
Menu Selections (Adjustments) ........... 41
Picture Adjustment (“Picture” menu) .. 43
Selecting the Picture Mode .................. 43
Adjusting the Image ............................. 43
Adjusting the Color Temperature ......... 44
Adjusting the Colors ............................. 44
Progressive ........................................... 44
Reducing Image Noise (DNR) ............. 45
Switching the Iris Setting ..................... 45
Lamp Setting ........................................ 45
Setup
Setting up the Projector ...................... 18
Setting up the Projector ....................... 18
Standard Setup (Front Projection) ....... 18
Ceiling-mount Setup ............................ 18
Projection (PRJ) Mode ......................... 19
Picture (Screen) Size and Projection
Distance ............................................. 20
Connections
Samples of Cables for Connection..... 22
Connecting to Video Equipment......... 23
Connecting to a Computer ................. 27
Computer Image Adjustment
(“Fine Sync” menu)........................... 46
Adjusting the Computer Image ........... 46
Special Modes Setting ......................... 46
Auto Sync (Auto Sync Adjustment) ..... 46
Checking the Input Signal ................... 46
Using the “Options” Menu ................... 47
Adjusting the Overscan ....................... 47
Adjusting the Vertical Size of the Display
(Subtitle Setting) ................................ 47
Setting the On-screen Display ............. 48
Setting the Video System ..................... 48
Signal Type Setting .............................. 48
Selecting the HDMI Setting .................. 48
Selecting the Background Image ........ 48
Auto Power Off Function ...................... 49
Checking the Lamp Life Status ........... 49
Reversing/Inverting Projected
Images ............................................... 49
Selecting the Transmission Speed
(RS-232C) .......................................... 50
Reducing the Power Consumption When
the Power Is in Standby Mode .......... 50
Fan Mode Setting ................................. 50
Returning to the Default Settings ......... 50
Selecting the On-screen Display
Language ........................................... 50
4
Reference
Introduction
Appendix
Maintenance ....................................... 51
Cleaning and Replacing
the Dust Filters ................................. 52
Maintenance Indicators ...................... 54
Regarding the Lamp ........................... 56
Lamp ..................................................... 56
Caution Concerning the Lamp ............ 56
Replacing the Lamp ............................. 56
Removing and Installing
the Lamp Unit .................................... 57
Resetting the Lamp Timer .................... 58
Connecting Pin Assignments ............. 59
Computer Compatibility Chart ............ 60
Troubleshooting .................................. 61
Service Information (For the U.S.) ..... 62
Specifications ..................................... 63
Dimensions ......................................... 64
Index ................................................... 65
CONSUMER LIMITED WARRANTY
(VALID IN USA ONLY) ..................... 66
LIMITED WARRANTY
(VALID IN CANADA ONLY) .............. 67
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
1. Read Instructions
All the safety and operating instructions should
be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be
retained for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be
followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
11. Power Sources
This product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
14. Lightning
For added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power-line surges.
6
Introduction
15. Overloading
Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can
result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. Servicing
Do not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for
service.
19. Replacement Parts
When replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
22. Heat
This product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
• The DLP® logo, the DLP® medallion and BrilliantColor™ are trademarks of Texas Instruments.
• Microsoft
®
and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Macintosh
®
is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp ruptures. In
case of lamp rupture, contact
your nearest Sharp Authorized Service Center or
Dealer for replacement.
See “Replacing the Lamp” on
page 56.
Caution concerning the setup of the projector
■ For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from
humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more often. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Service Center or
Dealer.
Do not set up the projector in places exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (8 degrees) of the adjust-
ment foot.
■ After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projector is used for a while.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 4,900 feet (1,500 meters)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in
a high position
■ When placing the projector in a high position,
make certain it is carefully secure to avoid
personal injury caused by the projector falling down.
Do not subject the projector to hard impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of temperature.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
■ Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
■ Be sure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat
damage. This does not indicate a malfunction. (See pages 54 and 55.) Remove the projector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
8
■ When turning off the projector, the cooling fan
runs to decrease the internal temperature for
a while. Unplug the power cord after the cooling fan stops. The period the cooling fan runs
will vary, depending on the circumstances and
the internal temperature.
Caution regarding usage of the projector
■ When using the projector, take care not to
subject it to hard impact and/or vibration, as
this can result in damage. Take extra care with
the lens. Before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other cables
connected to it.
■ Do not carry the projector by holding the lens.
■ When storing the projector, ensure you at-
tach the lens cap. (See page 11).
■ Do not expose the projector to direct sunlight
or place next to heat sources. Doing so may
affect the cabinet color or cause deformation
of the plastic cover.
Other connected equipment
■ When connecting a computer or other audiovisual equipment to the projector, make the
connections AFTER unplugging the power
cord of the projector from the AC outlet and
turning off the equipment to be connected.
■ Please read the operation manuals of the projector and the equipment to be connected for
instructions on how to make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Temperature monitor function
■
If the projector starts to overheat due to setup
problems or blockage of the air vents, “ ” and
“ ” will illuminate in the lower left corner
of the picture. If the temperature continues to
rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after
a 90-second cooling-off period the projector will
enter standby mode. Refer to “Maintenance Indicators” on page 54 for details.
Info
• The cooling fan regulates the internal temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in
the fan speed. This does not indicate malfunction.
• Do not unplug the power cord during projection or cooling fan operation. This can cause
damage due to rise in internal temperature,
as the cooling fan also stops.
Introduction
9
Accessories
Supplied accessories
Remote control
RRMCGA543WJSB
Power cord
QACCDA007WJPZ
Two R-03 batteries
(“AAA” size, UM/SUM-4,
HP-16 or similar)
• Operation manual
Lens cap (attached)
CCAPHA024WJSA
Optional accessories
■ Lamp unit
■ 3 RCA to 15-pin D-sub cable (10' (3.0 m))
Note
• Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Service Center or Dealer.
AN-XR10L2
AN-C3CP2
10
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Projector
Top View
Power
indicator
28, 5428, 54
Lamp indicator
Introduction
STANDBY/ON
button
For turning the
power on and
putting the
projector into
standby mode.
ENTER button
For setting
items selected
or adjusted on
the menu.
RESIZE button
For switching
the screen
size.
Front View
Focus ring
For adjusting
the focus.
HEIGHT
ADJUST
lever
30
30
28
41
36
Temperature warning
54
indicator
INPUT buttons (P/R)
29
For switching input mode
1, 2, 3, 4, 5 or 6.
MENU button
41
For displaying
adjustment and
setting screens.
Adjustment buttons
41
(P/R/O/Q)
For selecting menu items.
Intake vent
51
Zoom ring
30
For enlarging/
reducing the picture.
Remote control
15
sensor (front)
Push both sides of the lens cap
to attach or remove.
11
Part Names and Functions (Continued)
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Rear View
Exhaust vent
51
Intake vent
AC socket
Connect the
supplied Power cord.
Rear adjustment
foot
Terminals
51
28
31
65 4 1 23
Terminal Description
INPUT 1, 2 terminal
1
Connecting video equipment with component output terminal (DVD
player, DTV decoder, DVD recorder with hard disc, etc.).
INPUT 3 terminal
Connecting video equipment with S-video output terminal (VCR, DVD
2
player, etc.).
INPUT 4 terminal
3
Connecting video equipment without S-video output terminal.
INPUT 5 terminal
4
5
6
■ Connecting video equipment with component output terminal
(DVD player, DTV decoder, DVD recorder with hard disc, etc.).
■
Connecting the computer.
INPUT 6 terminal
Connecting video equipment with HDMI output terminal.
RS-232C terminal
Serviceman only
Remote control
15
sensor (rear)
Kensington
13
Security Standard
connector
Page
23
24
24
25
27
26
—
12
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
ON button
28
For turning the power on.
INPUT 1, 2, 3, 4, 5 and 6
STANDBY button
For putting the
projector into the
standby mode.
KEYSTONE button
For entering the
Keystone Correction
mode.
RETURN button
For returning to the
previous menu screen
during menu operations.
AUTO SYNC button
For automatically
adjusting images
when connected to a
computer.
RGB/COMP. button
For switching to the
respective input signal type.
FREEZE button
For freezing images.
29
32
41
46
48
38
29
buttons
For switching to the
respective input modes.
MENU button
41
For displaying adjustment
and setting screens.
Adjustment buttons
41
(P/R/O/Q)
• For selecting menu items.
• For adjusting the Keystone
Correction when in the
Keystone Correction mode.
ENTER button
41
For setting items selected
or adjusted on the menu.
RESIZE button
36
For switching the picture
size (STRETCH, SIDE
BAR, etc.).
PICTURE MODE button
38
For selecting the appropriate
picture.
Introduction
Backlight button
For lighting all buttons on the
remote control.
Using the Kensington Lock on the projector
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for instructions
on how to use it to secure the projector.
IRIS button
38
For switching “HIGH
BRIGHTNESS MODE” and
“HIGH CONTRAST MODE”.
13
Part Names and Functions (Continued)
Inserting the Batteries
Press the P mark on the cover and slide it
1
in the direction of the arrow.
Insert the batteries.
2
• Insert the batteries making sure the polarities
correctly match the m and n marks inside the
battery compartment.
Attach the cover and slide it until it clicks
3
into place.
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove
them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
14
Usable Range
The remote control can be used to control the projector within the ranges shown in the illustration.
Remote control sensor (front)
30°
Introduction
Remote
control signal
transmitters
30°
Remote control
Note
• The signal from the remote control can be reflected off a screen for easy operation. However, the
effective distance of the signal may differ depending on the screen material.
23n (7 m)
Remote control sensor (rear)
23n (7 m)
Remote control
30°
30°
Remote
control signal
transmitters
When using the remote control
• Ensure that you do not drop it or expose it to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp. In this case, move the projector
away from the fluorescent lamp.
15
Quick Start
This section shows the basic operation (projector connecting with the video equipment).
For details, see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the video equipment is explained using one example.
3
STANDBY/ON
8
button
INPUT buttons
5
Focus ring
6
Zoom ring
6
HEIGHT
6
ADJUST lever
STANDBY button
8
ON button
3
INPUT 4 button
5
KEYSTONE button
7
Adjustment buttons
7
(P/R/O/Q)
ENTER button
7
1. Place the projector facing a wall or a screen
_P. 18
2. Connect the projector to the video equipment and plug the power
cord into the AC socket of the projector
To INPUT 4 terminal
Connect the audio output of
AC socket
any video devices to an
appropriate audio device.
3. Remove the lens cap and turn the projector on
On the
projector
On the remote
control
_PP. 22–28
_P. 28
16
4. Turn the video equipment on and start playback
5. Select the INPUT mode
Select the “INPUT 4” using the INPUT buttons on the projector or the INPUT 4 button on the
remote control.
projector
On the
On the remote
control
On-screen display
_P. 29
INPUT 4
• When pressing the INPUT buttons on the projector, input mode switches in the following
order:
• Pressing the INPUT buttons on the remote control also allows you to switch the input mode.
6. Adjust the focus, image size, and projector angle
1. Adjust the focus by
7.
Correct trapezoidal distortion (GEOMETRIC ADJUSTMENT)
1. Press c KEYSTONE on the remote control.
2. Press P/R/O/Q on the remote control to set the upper-left position of the projected image.
3. Press i ENTER on the remote control to set the position.
4. Follow steps 2 and 3 to also set the upper-right, lower-right, and lower-left positions of the
projected image.
• When you confirm the lower left position, the screen adjustments will be set and setup will
INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6
turning the focus ring.
Focus ring
end.
2. Adjust the projection
image size by turning
the zoom ring.
Zoom ring
_PP. 30, 31
3. Adjust the projector
angle using the HEIGHT
ADJUST lever.
_PP. 32–35
Quick Start
8. Turn the Power off
Press the STANDBY/ON button on the projector or the STANDBY button on the remote control,
and then press the button again while the confirmation message is displayed to put the projector
into standby mode.
On the
projector
• Unplug the power cord from the AC outlet after the cooling fan stops.
On the remote
control
On-screen Display
_P. 29
17
Setting up the Projector
Setting up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector’s feet
flat and level. Doing so will eliminate the need for Keystone correction and provide the best image
quality.
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen according
to the desired picture size. (See page 20.)
Example of standard setup
Side View
Image
H
Lens center
Note
• Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Dis-
tance”.
Ceiling-mount Setup
■ It is recommended that you use the optional
Sharp ceiling-mount bracket for this installation. Before mounting the projector, contact
your nearest Sharp Authorized Service Center or Dealer to obtain the recommended ceiling-mount bracket (sold separately).
• AN-XRCM30 ceiling-mount bracket (for
U.S.A.).
• AN-60KT ceiling-mount bracket, its AN-
TK201 and AN-TK202 extension tubes (for
countries other than the U.S.A.).
■ Invert the image by setting “Ceiling + Front”
in “PRJ Mode”. See page 49 for use of this
function.
18
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the mode
most appropriate for the projection setting in use. (You can set the PRJ Mode in “Options2” menu.
See page 49.)
■ Table mounted, front projection
Menu item ➞ “Front”
■ Table mounted, rear projection
(with a translucent screen)
■ Ceiling mounted, front projection
Menu item ➞ “Ceiling + Front”
■ Ceiling mounted, rear projection
(with a translucent screen)
Menu item ➞ “Rear” Menu item ➞ “Ceiling + Rear”
Indication of the Projection Image Size and Projection Distance
Refer to page 20 for additional information concerning “Picture (Screen) Size and Projection Distance”.
Example: When using a wide screen (16:9)
Picture (Screen) Size
300"
200"
100"
80"
60"
52"
×
70"
29"
87"
×
×
39"
49"
174"
×
98"
261"×147"
Setup
5'11
6'11
"–
(1.8 m
"
– 2.1 m)
7'11
(2.4 m
"–
9'2
"
2.8 m)
–
9'11
11'6
"–
(3.0 m
"
3.5 m)
–
19'10
(6.0 m
22'11
"–
7.0 m)
–
29'9
"
"
(9.1 m
5
34'
–
– 10.5 m)
Projection
Distance
"
19
Setting up the Projector (Continued)
Picture (Screen) Size and Projection Distance
The projection screen size varies according to the distance from the lens of the projector to the screen. Install the projector so that projected images are projected onto the
screen at the optimum size by referring to the table below. Use the values in the table
as a reference when installing the projector.
When using a wide screen (16:9) and projecting 16:9 image
Picture (Screen) size Projection distance [L]
Diag. [χ] Width Height
300 (762 cm)
270 (686 cm)
250 (635 cm)
200 (508 cm)
150 (381 cm)
100 (254 cm)
80 (203 cm)
70 (178 cm)
60 (152 cm)
40 (102 cm)
χ
: Picture (Screen) size (diag.) (in/cm)
L: Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H: Distance from the lens center to the bottom of the image (in/cm)
261 (664 cm)
235 (598 cm)
218 (553 cm)
174 (443 cm)
131 (332 cm)
87 (221 cm)
70 (177 cm)
61 (155 cm)
52 (133 cm)
35 (89 cm)
147 (374 cm)
132 (336 cm)
123 (311 cm)
98 (249 cm)
74 (187 cm)
49 (125 cm)
39 (100 cm)
34 (87 cm)
29 (75 cm)
20 (50 cm)
Minimum [L1] Maximum [L2]
9 (9.1 m)
29
9 (8.2 m)
26
9 (7.5 m)
24
10 (6.0 m)
19
10 (4.5 m)
14
11 (3.0 m)
9
11 (2.4 m)
7
11 (2.1 m)
6
11 (1.8 m)
5
0 (1.2 m)
4
5 (10.5 m)
34
11 (9.4 m)
30
8 (8.7 m)
28
11 (7.0 m)
22
2 (5.2 m)
17
6 (3.5 m)
11
2 (2.8 m)
9
0 (2.4 m)
8
11 (2.1 m)
6
7 (1.4 m)
4
When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)
Picture (Screen) size Projection distance [L]
Diag. [χ]
300 (762 cm)
270 (686 cm)
250 (635 cm)
200 (508 cm)
150 (381 cm)
100 (254 cm)
80 (203 cm)
70 (178 cm)
60 (152 cm)
40 (102 cm)
χ
: Picture (Screen) size (diag.) (in/cm)
L: Projection distance (ft/m)
L1: Minimum projection distance (ft/m)
L2: Maximum projection distance (ft/m)
H: Distance from the lens center to the bottom of the image (in/cm)
Width Height
240 (610 cm)
216 (549 cm)
200 (508 cm)
160 (406 cm)
120 (305 cm)
80 (203 cm)
64 (163 cm)
56 (142 cm)
48 (122 cm)
32 (81 cm)
180 (457 cm)
162 (411 cm)
150 (381 cm)
120 (305 cm)
90 (229 cm)
60 (152 cm)
48 (122 cm)
42 (107 cm)
36 (91 cm)
24 (61 cm)
Minimum [L1] Maximum [L2]
4 (11.1 m)
36
9 (10.0 m)
32
4 (9.2 m)
30
3 (7.4 m)
24
2 (5.5 m)
18
1 (3.7 m)
12
8 (3.0 m)
9
6 (2.6 m)
8
3 (2.2 m)
7
10 (1.5 m)
4
42
1 (12.8 m)
10 (11.5 m)
37
1 (10.7 m)
35
1 (8.6 m)
28
0 (6.4 m)
21
0 (4.3 m)
14
3 (3.4 m)
11
10 (3.0 m)
9
5 (2.6 m)
8
7 (1.7 m)
5
Distance from the lens center
to the bottom of the image [H]
1
/32 (53 cm)
21
15
/16 (48 cm)
18
17
/32 (45 cm)
17
1
/64 (36 cm)
14
33
/64 (27 cm)
10
1
/64 (18 cm)
7
39
/64 (14 cm)
5
29
/32 (12 cm)
4
13
/64 (11 cm)
4
51
/64 ( 7 cm)
2
The formula for picture size and projection distance
[Feet/inches]
L1 (ft) = 0.03019χ / 0.3048
L2 (ft) = 0.03493χ / 0.3048
H (in) =0.17808χ / 2.54
[m/cm]
L1 (m) = 0.03019
L2 (m) = 0.03493
H (cm) = 0.17808
χ
χ
Distance from the lens center
to the bottom of the image [H]
47
/64 (65 cm)
25
11
/64 (59 cm)
23
29
/64 (54 cm)
21
5
/32 (44 cm)
17
7
/8 (33 cm)
12
37
/64 (22 cm)
8
55
/64 (17 cm)
6
6 (15 cm)
9
/64 (13 cm)
5
7
/16 (9 cm)
3
The formula for picture size and projection distance
[Feet/inches]
L1 (ft) = 0.03694χ / 0.3048
L2 (ft) = 0.04275χ / 0.3048
H (in) = 0.21794χ / 2.54
[m/cm]
L1 (m) = 0.03694
L2 (m) = 0.04275
H (cm) = 0.21794
χ
χ
χ
χ
20
Loading...