SHARP DM-2005, DM-2010 Service Manual

DM-2010

CODE: 00ZDM2010/A1E

NETWORK LASER SYSTEM

DM-2005

MODEL DM-2010

CONTENTS

[ 1 ] INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 2 ] DIFFERENCE FROM THE DM-2000 . . . . . . . . . . . . 1 - 1

[ 3 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 4 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . 1 - 3

[ 5 ] INTERNAL STRUCTURES . . . . . . . . . . . . . . . . . 5 - 1

[ 6 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . 6 - 1

[ 7 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[ 8 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[ 9 ] FAX SOFT SWITCH . . . . . . . . . . . . . . . . . . . . . 6 - 2

[10] FLASH ROM VERSION UP PROCEDURE . . . . . . . . . 6 - 2

[11] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . 6 - 2

[12] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . 6 - 2

[13] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . 6 - 2

[14] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . 6 - 2

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION

for after sales service only. The contents are subject to change without notice.

DM-2010

[1] INTRODUCTION

This model is an upgrade model of the DM-2000 network laser. This Service Manual, therefore, describes only the different points from the DM-2000 as well as the supplement items. For the items which are not described in this Manual, please refer to the DM-2000 Service Manual and Parts Guide.

[2] DIFFERENCE FROM THE DM-2000

For details of the specifications, refer to the basic specifications described later.

DM-2000 DM-2005 DM-2010

Copy speed 20PPM 20PPM 20PPM

Standard paper feed tray 2 steps + MB 2 steps + MB 2 steps + MB

Option paper feed tray Attachable Attachable Attachable 1 step or only one of 2 steps

Shifter (Offset paper exit) Standard Standard Standard

Job separator Standard Standard Standard

Page Memory Standard (10MB) Standard (10MB) Standard (10MB)

Scan one Print multi Standard ∗1 Standard ∗1 Standard ∗1

Document detection (Platen) Standard Standard Standard

Electrical Sort Option Option Option

SPF/RSPF SPF option RSPF standard SPF standard

LCD Display Standard ∗2 Standard ∗2 Standard ∗2

Printer Function (PCL6) Standard Standard Standard

Printer Function (PS2) Standard Standard Standard

Network Interface PWB Standard ∗3 Standard ∗3 Standard ∗3

Fax Function Option Option Option

∗1: The paper exit style is group only, sort is not available. ∗2: The copy mode status is not displayed. The status of printer and FAX is displayed. ∗3: Attached when installing the machine.

[3] SPECIFICATIONS

1. Copy mode

A. Type

Type Desk-top

B. Copy speed

(1) Basic speed

1 scan multi copy 20 sheets/min

Condition: Copy speed in the normal copy.

(2) Continuous copy speed (Sheets/min)

Paper size Normal

11" × 17" 10 10 10

8.5" × 14" 12 12 12

Inch

system

8.5" × 13" 12 12 12

8.5" × 11" 20 20 20

8.5" × 11"R 15 15 15

8.5" × 5.5" 20 20 20

C. First copy time

(1) Basic speed

First copy time 7.2 sec (8.5" × 11"/1st cassette/with OC)

Enlargement

(200%)

Reduction

(50%)

D. Document

Max. document size 11" × 17"

Document reference position Left side center

Detection (Platen) Available

Detection size

(1) SPF/R-SPF

Standard/ Option

Document load capacity

Document size (Max. ∼ Min.)

Document replacement speed

Document set/Paper feed direction

Document weight 56 ∼ 90 g/m2, 15 ∼ 23.9 lbs

Document size detection On the document feed tray

Document mixture Copy mode: Not Available

DM-2005 RSPF: Standard

DM-2010 SPF: Standard

11" × 17", 8.5" × 14",

8.5" × 11", 8.5" × 11"R,

8.5" × 5.5"

30 sheets (56 ∼ 90 g/m2 15 ∼ 23.9 lbs equivalent)

11" × 17" ∼ 8.5" × 5.5"

16 sheets/min (8.5" × 11" normal copy)

Face up, Center reference, Paper feed from the top

1 – 1

DM-2010

E. Paper feed

Copy size

Paper feed system

Paper feed capacity

Remaining quantity detection

(1) Paper feed section of the copier

Paper feed size

Side front Front 2 step

Paper feed capacity

Detection

Weight 56 ∼ 80 g/m

Special paper Recycled paper

(2) Manual paper feed section

Paper feed size 11" × 17" ∼ 5.5" × 8.5"

Paper feed capacity 100 sheets

Detection

Weight 56 ∼ 128 g/m2 15 ∼ 34 lbs

Special paper Recycled paper, OHP film, labels

Paper feed Single except for recycled paper

(3) Option paper feed unit

Model DM-DE1 DM-DE2

Paper feed size

Capacity (56 ∼ 80 g/m2)

Paper weight

Dehumidifier heater

Detection

Paper size setting

External dimensions (W × D × H)

Weight About 5 kg About 10 kg

Special paper

Max.: A3, 11" × 17" Min.: A6, 5.5" × 8.5" (For B6/A6 and 5.5" × 8.5", Multi bypass tray only.)

2 cassette + Multi bypass tray

250 × 2 (Paper feed tray) + 100 (Multi bypass tray)(56 ∼ 80 g/m

Cassette section

Multi bypass tray

11" × 17", 8.5" × 14", 8.5" × 13", 8.5" × 11",

8.5" × 11"R, 8.5" × 5.5" (8.5" × 5.5" is only for tray 1)

250 sheets (56 ∼ 80 g/m equivalent)

Paper empty detection available, size detection (by key input) Detection size: 11" × 17", 8.5" × 14",

8.5" × 11", 8.5" × 11"R, 8.5" × 5.5"

Size detection not available, paper empty detection available

1-step paper feed unit 2-step paper feed unit

11" × 17", 8.5" × 14", 8.5" × 11",

About 250 sheets

× 1 step

Paper empty detection, size detection

590 × 571 × 88 mm 590 × 571 × 173.5 mm

equivalent)

Empty detection available, size detection by key input

Only empty detection available

15 ∼ 21 lbs

8.5" × 11"R

About 250 sheets

× 2 steps

56 ∼ 80 g/m2 15 ∼ 21 lbs

None

(by key input)

User setting (by key input)

Recycled paper

F. Job speed

S-S (1st step) 80% (document replacement rate)

Condition: With SPF

G. Multi copy

Max. number of multi copy 99 sheets

H. Warmup time

Warmup time

Pre-heat Available

Approx. 35 sec (Condition: Standard condition)

I. Copy magnification ratio

Fixed magnification ratio

Zooming 50 ∼ 200%

Independent zooming/vertical

Independent zooming (horizontal)

50, 64, 77, 95, 100, 121, 129, 141, 200%

Available (50 ∼ 200%)

J. Print density

Density mode Auto/Manual/Photo

No. of manual adjustment

Toner save mode Set by the user program

5 steps (Manual/Photo)

K. Void width

Void area

Image loss

Lead edge 1 ∼ 4 mm, rear edge 4 mm or less, both side 4 mm or less

Max. 5/32" (4 mm) (leading and trailing edges) Max. 5/32" (4 mm) (along other edges in total)

L. Auto duplex

Standard/Option

DM-2005 Standard

DM-2010 Not installable

M. Paper exit/finishing

Paper exit section capacity

Job separator

Full detection Available (Job separator)

Finishing Electronic sort board: Option (DM-EB1)

Electronic sort capacity

Offset function Available (by the shifter)

Staple function None

Face down 250 sheets

Job separator, Standard provision

Upper: FAX/Printer, Lower: Copier Upper: 100 sheets, Lower 150 sheets

8.5" × 11" standard document 60 sheets

1 – 2

DM-2010

(1) Electronic sort board (Option)

60 sheets of A4 (8.5" × 11") standard documents

Electronic sort

Rotation copy

2 in 1, 4 in 1

Edge erase

Center erase

Margin shift

Sorting

Grouping

If there is paper of same size as the document, the image is rotated to copy even though the paper is set in the different direction from the document direction.

Copies of 2 pages or 4 pages are integrated into one surface. Divided by solid lines, (Selectable by the user program.)

Images surrounding the document are erased when copying. (Adjustable in 0 ∼ 20 mm (5 mm step)/0" ∼ 1" (1/4" step) by the user program.)

The image at the center is erased when copying. (Adjustable in 0 ∼ 20 mm (5 mm step)/0" ∼ 1" (1/4" step) by the user program.)

Binding margin is made at the left edge of the set documents.

N. Additional functions

APS

AMS

Duplex Available only in DM-2005

Document count

Sorter

Independent zooming Vertical/Horizontal: 50 ∼ 200%

1 set 2 copy

Binding margin Shift width 9 mm/1/4"

Edge erase Adjustable 0 ∼ 20 mm/0" ∼ 1"

Black-white reversion Whole surface only

2 in 1, 4 in 1

Rotation copy

Memory copy Only one page memory installed.

Pre-heat function Conditions set by the user program

Auto power shut off function

Auto tray switching

Message display (FAX/Printer extension)

User program

Total counter

: When an option is installed : Available : Not available

(APS not available by flowing in during use of SPF)

(AMS not available by flowing in during use of SPF)

When the electronic sort board installed.

Enlargement inhibited, inhibited during the use of SPF

Conditions set by the user program

P. Other specifications

Photoconductor type OPC (Organic Photo Conductor)

Photoconductor drum dia. 30 mm

Copy lamp Xenon lamp

Developing system

Charging system Saw teeth charging

Transfer system (+) DC corotoron

Separation system (–) DC corotoron

Fusing system Heat roller

Cleaning system Contact blade

Dry 2-component magnetic brush development

Q. Package form

Body

Body/Accessories (NIC board is separately packed.)

R. External view

External dimensions (W × D × H)

Occupying area (W × D)

Weight About 43 kg

590 × 531 × 654 mm (without SPF)

590 × 531 mm (When the multi bypass tray is installed.)

S. Power source

Voltage AC120V ± 15%

Frequency 50/60Hz common

T. Power consumption

Max. power consumption About 1.5 KWh

∗ EnergyStar standard (The second level conformity)

Pre-heat About 60 Wh

Auto power shut off About 4.8 Wh

U. Digital performance

Resolution

Gradation

Reading 400 dpi

Writing 600 dpi

Reading 256 gradations

Writing Binary

2. Printer Mode

For this item, refer to the DM-2000 Service Manual.

3. Fax Mode (Only DM-2010)

For this item, refer to the DM-FX1 Service Manual.

O. Machine composition

(1) Option

Machine Model Power supply

250 sheets paper feed unit DM-DE1 Supplied by the copier.

500 sheets paper feed unit DM-DE2 Supplied by the copier.

Electronic sorting kit DM-EB1 Supplied by the copier.

Facsimile expansion kit DM-FX1

2 MB FAX memory AR-MM5

4 MB FAX memory AR-MM6

8 MB FAX memory AR-MM7

Supplied by the copier. DM-2010: Standard

[4] CONSUMABLE PARTS

For this item, refer to the DM-2000 Service Manual.

1 – 3

+ 9 hidden pages