19U-M100,19U-M100S
CU19M10
SERVICE MANUAL
S12E719U-M100
COLOR TELEVISION
Chassis No. SN-010
POWER
–
VOL
+
C
H
M
E
N
U
19U-M100, 19U-M100S
MODELS
CU19M10
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS .........................................................................................................1
» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................2
» LOCATION OF USER'S CONTROL .....................................................................................................6
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................7
» CHASSIS LAYOUT .............................................................................................................................13
» BLOCK DIAGRAM..............................................................................................................................15
» SCHEMATIC DIAGRAMS ...................................................................................................................17
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................26
» REPLACEMENT PARTS LIST............................................................................................................29
» PACKING OF THE SET ......................................................................................................................37
ELECTRICAL SPECIFICATIONS
POWER INPUT.....................................................AC 120 V, 60 Hz
POWER RATING ....................................................................69 W
PICTURE SIZE ........................................... 1,194cm2 (185sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
AUDIO POWER
OUTPUT RATING ..................................................... 1 W (RMS)
SHARP CORPORATION
(Nominal)
SPEAKER
SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE............................. 32 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF.....................................................75 ohm Unbalanced
TUNING RANGES
VHF-Channels...............................................................2 thru 13
UHF-Channels ............................................................14 thru 69
CATV Channels ...........................................................1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
1
19U-M100,19U-M100S
CU19M10
IMPORTANT SERVICE SAFETY PRECA UTION
Ë
Service work should be performed only b y qualified service technicians who are thor oughl y
familiar with all safety checks and the servicing guidelines whic h f ollo w:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC v oltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE ONLY
4A 125V
WITH SAME TYPE 4A-125V
FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all ser vice personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. Ho we ver, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the r ated value
-no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry.
6. When troubleshooting and taking test measurements
on a receiver with excessiv e high voltage, a void being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
2
2
2
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
19U-M100,19U-M100S
CU19M10
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
» Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
» Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
» Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the A C v oltage drop
across the resistor.
» Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessar y, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp .
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken bef ore returning the
instrument to the customer.
1.5k ohm
10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
CONNECT TO
KNOWN EARTH
GROUND
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
3
19U-M100,19U-M100S
CU19M10
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ë
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur a deux systèmes de mise
à la terre qui sont séparés par un matériau isolant.
Le système de mise à la terre non-isolée (chaud)
est pour le circuit du régulateur de tension B+ et le
circuit de sortie horizontale. Le système de mise à
la terre isolé est pour les basses tensions C. C. B+
et le circuit secondaire du transformateur de haute
tension.
PRECAUTION:POUR LA
PROTECTION CONTINUE
CONTRE LES RISQUES
4A 125V
D'INCENDIE, REMPLACER LE
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V .
REPARA TION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 k en série a vec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le cor den d'alimentation doit être
retiré de la prise murale.)
1. Il est à noter que le tube-image de ce récepteur est
intégralement protégé contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesurab les si la haute tension est maintenue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est
excessive que les rayons X peuvent entrer dans
l'enveloppe du tube-image y compris le conducteur
de verre. Il est important de maintenir la haute tension
en-dessous du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
voltmètre à haute tension qui doit être
périodiquement étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime-et pas plus haute. L'opération à
des tensions plus élevées peut entraîner une panne
du tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation
X. Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive , éviter de s'approcher in utilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
4
19U-M100,19U-M100S
2
2
CU19M10
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
» Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
» A l'aide de deux fils à pinces, brancher une résistance
de 1,5 kΩ 10 watts en parallèle av ec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
» Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
» Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance.
Toutes les vérifications doivent être refaites après
avoir inversé la fiche du cordon d'alimentation. (Si
nécessaire, une prise d'adpatation non polarisée peut
être utilisée dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
Voltmètre CA
1.5k ohm
10W
0.15µF
SONDE D'ESSAI
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
AUX PIECES
METALLIQUES
EXPOSEES
identifiées par la marque "
BRANCHER A UNE
TERRE CONNUE
å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
5
19U-M100,19U-M100S
CU19M10
Front Panel
SENSOR AREA FOR
REMOTE CONTROL
POWER
Press → On.
Press again → Off.
LOCATION OF USER'S CONTROL
POWER
– VOL +CH
MENU
POWER
– VOL +CH
MENU
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
CHANNEL UP/DOWN – MENU
(
') Selects next higher channel.
(
) Selects next lower channel.
"
• Press both at the same time to
access the MAIN MENU screen.
Basic Remote Control Functions
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
Infrared Transmitter Window
INPUT
Press → Switch to e xternal video input
mode.
Press again → Switch to TV mode.
CHANNEL UP/DOWN
(
') Selects next higher channel.
(
) Selects next lower channel.
"
•
Moves the “ ” mark of the MENU
screen.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
TV
6
19U-M100,19U-M100S
CU19M10
INSTALLATION AND SERVICE INSTRUCTIONS
Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2)Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and mak e sure
that the voltmeter reads 21.4 ±1.5 V.
5. Apply external 27.2V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before
the set is returned to the customer.
HIGH VOLT A GE CHECK
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly
tuned in test signal.
3. Enter the ser vice mode and select the service
adjustment "S03" and Bus data "01" (Y-mute on).
4. The voltage should be approximately 26.0kV (at zero
beam).
If a correct reading cannot be obtained, check
circuitry for malfunctioning components. After the
voltage test, make Y-mute off to the normal mode.
7
19U-M100,19U-M100S
CU19M10
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow
the steps below whenever the service adjusment is required.
To enter the service mode and exit service mode.
While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket.
Now, the TV set is switched on and enters the service mode.
To exit the service mode, turn the television off by pressing the power button.
1. Service mode.
Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset
function in the video adjustment menu to ensure customer control are in their proper (reset) position.
2. Service number selection.
In the service mode, you will see the window screen as window 1. There are 3 adjustment categories 2DEF,
3SIGNAL, 4FIX VALUE as show in Figure A.
Window 2: DEF
D01
D03
D05
RETURN
RETURN
Window 4: FIX VALUE
RETURN NEXT
D02
D04
D06
Window 1: ADJUSTMENT CATEGORIES
RETURN
F01 F02
F13 F14
DEF
SERVICE MODE
DEF
SIGNAL
FIX V ALUE
EEPROM
NEXT
PREVIOUS
SIGNAL
FIX V ALUE
Window 3: SIGNAL
S01
S13
RETURN
F15 F16
F25 F26
RETURNPREVIOUS
S02
S12
RETURN
Figure A: ADJUSTMENT CATEGORIES
Press CH UP/DOWN button for selection and enter by VOL UP or VOL DOWN.
Press CH UP/DOWN button to select the adjustment item and VOL UP/DOWN
to adjust the data number for each categories.
(OSD disturbance can be erased by R/C display key)
(Note: EEPROM – factory used only)
8
Below are the adjustments ranges and initial values for FIX VALUE category.
FIX V ALUE
SERVICE
POSITION
F01 OPTION 1 00-FF B0
F02 OPTION 2 00-FF 04 04
F03 E-SAVE 00-3F 23 2A
F04 TUNER SETUP 00, 01 00 00
F05 R-TONE RD 00-7F 19 03
F06 R-TONE BD 00-7F 00 7C
F07 B-TONE RD 00-7F 00 00
F08 B-TONE BD 00-7F 12 04
F09 FM LEVEL 00-1F 0C 0C
F10 AFC GAIN 00, 01 00 00
F11 G DRIVE 00, 0F 0F 0F
F12 FBT BLK SW 00, 01 01 01
F13 V COMP 00-07 07 07
F14 OSD CONT 00-07 02 00
F15 SHARPNESS 00-3F 19
F16 FLT SYS 00-03 00 00
F17 KILLER OP 00-07 04 02
F18 PRE SHOOT 00-03 03 00
F19 CORING 00-07 07 04
F20 DC REST 00-03 02 02
F21 BS START 00-03 01 01
F22 BS GAIN 00-03 01 01
F23 ABL START 00-07 00 00
F24 R/B ANGLE 00-0F 08 08
F25 H BLK R 00-07 04 03
F26 H BLK L 00-07 04 00
ADJUST ITEM
RANGE
Table - A
INITIAL VALUE
19U-M100,19U-M100S
CU19M10
DATA
(Hex)
B0(19U-M100/100S),A0(CU19M10)
19(Matsushita Tuner),11(SHARP Tuner)
Below are the ranges and initial values for each adjustment and in each categories.
DEF
SERVICE
POSITION
D01 H-PHASE 00-1F 0C
D02 V-SIZE 00-7F 40
D03 V-POSITION 00-3F 20 Must be "20"
D04 CC-POSITION 00-FF 1A
D05 V-LINEARITY 00-1F 10 Must be "18"
D06 V-S-CORRECTION 00-1F 10 Must be "0C"
ADJUST ITEM
RANGE
DATA
Table - B
INITIAL V ALUE
ADJUSTMENT CONTENTS
SIGNAL
SERVICE
POSITION
S01 RF AGC 00-3F 14
S02 VIDEO LEVEL 00-07 03
S03 Y-MUTE 00-03 00
S04 SUB BIAS 00-FF 40 Must be "30"
S05 R-BIAS 00-FF 00
S06 G-BIAS 00-FF 00
S07 B-BIAS 00-FF 00
S08 R-DRIVE 00-7F 53
S09 B-DRIVE 00-7F 53
S10 CONTRAST 00-7F 5A
S11 TINT 00-7F 40
S12 COLOR 00-7F 40
S13 BRIGHTNESS 00-7F 40
ADJUST ITEM
RANGE
Note: Refer to the SERVICE ADJUSTMENT for each corresponding values.
DATA
Table - C
INITIAL V ALUE
ADJUSTMENT CONTENTS
"01":Y-MUTE, "02":V-STOP&Y-MUTE
"03":Activate color killer
9
19U-M100,19U-M100S
CU19M10
Holding down both the Vol-up/Ch-down buttons on the TV set at service mode f or more than 2 seconds will automatically
write the above initial values into IC2101.
PART REPLACED
IC2001
IC201
IC2101
CRT
ADJUSTMENT
NECESSARY
X
X
X
UNNECESSARY
X
Table - D
NOTES
Data is stored in IC2101.
The adjustment is needed to compensate for characteristics
of parts including IC201.
Holding down both the Vol-up/Ch-down buttons on the TV set
in the service mode for more than 2 seconds will automatically
write the above initial values into IC2101.
Adjust items related to picture tube only.
10
Ë
SERVICE ADJUSTMENT
19U-M100,19U-M100S
CU19M10
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select
the service adjustment "S01".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
Note: You have to exit the service mode first to
select another channel.
Video Level (TV Det Video Level)
Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select
the service adjustment "S02".
3. Set the data value to "02" first, then adjust the data
in ranges 02 ±2 step to obtain a normal contrast lev el.
Screen Adjustment
1. Connect to oscilloscope probe between TP855 and
ground of the CRT unit.
2. Receive a good local channel.
3. Enter the service mode Signal category and set the
service adjustment "S04" to step 30. Then select the
service adjustment "S12" and set the data value to
"00" to set the color level to the minimum le vel. (record
the original data first). You may skip this step, if you
selected a B/W picture or monoscope pattern. Set
also the "S05/S06/S07" data to minimum level.
4. Select the service adjustment "S03" and set the data
value to "01" to turn off the luminance signal (Y-mute).
5. Select the service adjustment "S13" and adjust the
data value to obtain 2.35 volts as shown in Figure B.
6. Adjust the master screen control until the raster
darkens to the point where raster is barely seen.
7. Adjust the service adjustment "S05" red, "S06" green
and "S07" blue to obtain a good grey scale with
normal white at low brightness level.
8. Select the service a adjustment "S03" and reset data
to "00". Select the service adjustment "S12" and reset
data to obtain normal color level.
9. Remove probe and reset the master screen control
to obtain normal brightness range.
White Balance Adjustment
1. Receive a good local channel.
2. Select the service adjustment "S12" and set the data
value to "00" to set the color level to the minimun.
You may skip this step, if you selected a B/W picture
or monoscope.
3. Alternately adjust the service adjustment data of
"S08" and "S09" until a good grey scale with normal
white is obtained.
4. Select the service adjustment "S12" and reset data
to obtain normal color level.
Sub-Picture Adjustment
1. Receive a good local channel.
2. Make sure the customer picture control is set to
maximum.
3. Enter the ser vice mode and select the service
adjustment "S10".
4. Adjust the data value to achieve normal contrast
range.
Sub-Tint Adjustment
1. Receive a good local channel.
2. Set the customer tint control to the center of it’s range.
3. Enter the ser vice mode and select the service
adjustment "S11".
4. Adjust "S11" data value to obtain normal fresh tones.
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position.
3. Enter the ser vice mode and select the service
adjustment "S12".
4. Adjust "S12" data value to obtain normal color level.
Sub-Brightness Adjustment
1. Receive a good local channel.
2. Make sure the customer brightness control is set to
center position.
3. Enter the ser vice mode and select the service
adjustment "S13".
4. Adjust "S13" data value to obtain normal brightness
level.
2.35 Vdc
Figure B: WAVEFORM FOR SCREEN ADJUSTMENT
GND
11
19U-M100,19U-M100S
CU19M10
Vertical-Size, V-Linearity and
V-S Correction Adjustments
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D02" for Vertical Size, "D05" for VLinearity and "D06" for V-S Correction Adjustment.
3. Set in order "D05" for V-Linearity, "D06" for V-S
Correction and set the data to get the best linearity.
4. Then adjust "D02" data until it become a proper
vertical size.
Horizontal Position Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D01".
3. Adjust "D01" data value to center the picture.
Vertical-Phase Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D03".
3. Adjust "D03" bus data to get the most acceptable
vertical position.
Note: The step range is 20 (032) ±10 steps.
Caption Position Adjustment (Horizontal)
1. Receive a good local channel.
2. Enter the service mode DEF category and select the
adjustment "D04".
3. A black text box will appear on the screen. (see
Figure C. below)
4. Adjust "D04" data value to balance the text box
position in the center (A=B).
A B
Figure C.
12
MODELS 19U-M100/100S CHASSIS LAYOUT
H
Ë
19U-M100
G
F
Ë
19U-M100S
19U-M100,19U-M100S
CU19M10
E
D
C
B
A
654321
13
19U-M100,19U-M100S
CU19M10
MODEL CU19M10 CHASSIS LAYOUT
H
G
F
E
D
C
B
A
654321
14
MODELS 19U-M100/100S BLOCK DIAGRAM
H
G
F
19U-M100,19U-M100S
CU19M10
E
D
C
B
A
654321
15
19U-M100,19U-M100S
CU19M10
MODEL CU19M10 BLOCK DIAGRAM
H
G
F
E
D
C
B
A
654321
16
DESCRIPTION OF SCHEMATIC DIAGRAM
19U-M100,19U-M100S
CU19M10
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5. indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set f or normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, g reen and b lue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
wavefor ms are measured from point indicated to
chassis ground.)
å
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
ç
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES åET HACHRES ( ):
PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
1.0
1.2
1160
1.0
25
220
WAVEFORMS
0.9
47
150
5.0
4.6
133
5.0
0.7
220
2.1
33
1.7
1.0
39.0
0.7
1.4
105
95
105
17
1918
19U-M100,19U-M100S
CU19M10
121110987654321
A
B
C
D
E
F
G
H
MODEL 19U-M100 SCHEMATIC DIAGRAM: MAIN Unit
2120
19U-M100,19U-M100S
CU19M10
121110987654321
A
B
C
D
E
F
G
H
MODEL 19U-M100S SCHEMATIC DIAGRAM: MAIN Unit
2322
19U-M100,19U-M100S
CU19M10
121110987654321
A
B
C
D
E
F
G
H
MODEL CU19M10 SCHEMATIC DIAGRAM: MAIN Unit
19U-M100,19U-M100S
CU19M10
MODEL 19U-M100 SCHEMATIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
654321
24
MODELS 19U-M100S, CU19M10 SCHEMATIC DIAGRAM: CRT Unit
H
G
F
19U-M100,19U-M100S
CU19M10
E
D
C
B
A
654321
25
19U-M100,19U-M100S
CU19M10
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
654321
26
19U-M100,19U-M100S
CU19M10
H
G
F
E
D
C
B
A
PWB-A: MAIN Unit (Chip Parts Side)
654321
27
19U-M100,19U-M100S
CU19M10
H
G
F
PWB-B: CRT Unit (Wiring Side)
E
D
C
B
PWB-B: CRT Unit (Chip Parts Side)
A
654321
28
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are
identified by å and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create
shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free; 1800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
' MARK: X-RAY RELATED PARTS
Ref. No. Part No. ★ Description Code
PICTURE TUBE
LISTE DES PIECES
CHANGE DES PIECES
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp
éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces
élelectriques qui pr élesentent ces particular it éles, sont rep éler élee
par la marque å et sont hachur élees dans les listes de pi`eces et dans
les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente
pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece
recommand élee parl'usine et dans ce manuel de service, peut provoquer
une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE 2. NO. DE REF
3. NO. DE PIECE 4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE
' MARQUE: PIECES RELATIVE AUX RAYONS X
Ref. No. Part No. ★ Description Code
PSPAG0017PEZZ R Spacer, x3 AC
QEARC1913PEZZ R Grounding Strap AF
'åV101 VB48LRH93X/~S J Picture T ube CC
19U-M100
'åDY601 RCiLH0201PEZZ R Deflection Y oke AZ
å L703 RCiLG0099PEZZ R Degaussing Coil AL
or
RCiLG0108GJZZ
or
RCiLG0014MEZZ
LHLDW0003PEKZ R Wire Holder, x4 AB
LHLDW1033PEZZ J Holder AA
PMAGF3045CEZZ J Purity Magnet AG
PSPAG0017PEZZ R Spacer, x3 AC
QEARC1913PEZZ R Grounding Strap AF
19U-M100S, CU19M10
'åV101 VB48KRD89X/4E R CRT(DY601:HA021WJ) CB
or
VB48KRD89X/3E CRT(DY601:H0100ME)
or
VB48QAD220X~S CRT(DY601:H0147PE)
or
VB510CKAY1S-S CRT(DY601:H0148PE)
'åDY601 RCiLHA021WJZZ R DY(V101:A48KRD89X/4E) BB
or
RCiLH0100MEZZ DY(V101:A48KRD89X/3E)
or
RCiLH0148PEZZ DY(V101:CPJ510CKAY1S)
or
RCiLH0147PEZZ DY(V101:A48QAD220X)
å L703 RCiLG0099PEZZ R Degaussing Coil AL
or
RCiLG0108GJZZ
or
RCiLG0014MEZZ
LHLDW0003PEKZ R Wire Holder, x4 AB
LHLDW1033PEZZ J Holder AA
PMAGF3046CEZZ R Purity Magnet AF
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
19U-M100
PWB-A DUNTKA358WEX9 – MAIN Unit —
PWB-B DUNTKA359WEV2 – CRT Unit —
19U-M100S
PWB-A DUNTKA358WEY0 – MAIN Unit —
PWB-B DUNTKA359WEV1 – CRT Unit —
CU19M10
PWB-A DUNTKA358WEY1 – MAIN Unit —
PWB-B DUNTKA359WEV1 – CRT Unit —
29
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU51 VTUVTST5UF770 J Tuner AZ
or
VTUENV56D82-1
INTEGRATED CIRCUITS
'å IC201 RH-iX3354CEN1 J LA76843N AT
IC351 VHiAN7511//-1 J AN7511 AK
å IC501 VHiLA7840//-1 J LA7840 AR
å IC701 VHiTEA1507/-1 J TEA1507P/N1 AL
å IC702 RH-FX0034CEZZ J PC817 AE
or
RH-FX0002GEZZ
or
RH-FX0029CEZZ
IC771 VHiKA7805AP-1 J KA7805API AE
or
VHiTA7805S/-1
IC2001 RH-iX3492CEZZQ R TMPA8700CPF AU
IC2040 VHiPST994C/-1 J PST994C AD
IC2101 VHiM24C16B/-1 J M24C16-BN6 AG
or
VHiBR24C16-1
TRANSISTORS
Q101 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198Y/-1
Q201 VS2SC2735//1E J 2SC2735 AC
Q451 VS2SA812-M51E J 2SA812 AC
or
VS2SA1530R/-1
Q452 VS2SA1266-Y-1 J 2SA1266-Y AA
Q601 VS2SC2482//-1 J 2SC2482 AD
å Q602 VS2SD2586//1E J 2SD2586 AM
Q631 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198-Y-1
å Q701 VSSPP04N60C-1 J SPP04N60C AH
or (19U-M100, 19U-M100S)
VSSPP07N60C-1
or
VS2SK2708//1E
or
VS2SK2645//-G
or
VSSTP6NC60+-1
or
VSSTP6NC60FP
or
VSSTP7NB60FP
å Q701 VS2SK2645++-1 J 2SK2645 (CU19M10) AN
or
VS2SK2708//1E
Q702 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198Y/-1
or
VS2SC1815Y/-1
Q751 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198-Y-1
Q752 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198-Y-1
Q2201 VS2SC1623L61E J 2SC1623 AB
or
VS2SC3928R/-1
or
VS2PD601ARQ-1
Q2211 VS2SC1623L61E J 2SC1623 AB
or
VS2SC3928R/-1
DIODES
D52 RH-EX0676GEZZ J Zener Diode, 32V AA
D101 RH-EX0616GEZZ J Zener Diode, 5.6V AA
D352 RH-DX0048GEZZ J Diode AA
or
VHD1SS119//-1
D353 RH-EX0644GEZZ J Zener Diode, 11V AB
D453 RH-EX0616GEZZ J Zener Diode, 5.6V AA
D455 RH-DX0048GEZZ J Diode AA
or
RH-DX0475CEZZ
D456 RH-DX0475CEZZ J Diode AB
D457 RH-EX0644GEZZ J Zener Diode, 13V AB
D458 RH-EX0644GEZZ J Zener Diode, 13V AB
D459 RH-DX0048GEZZ J Diode AA
or
VHD1SS119//-1
D502 RH-DX0131CEZZ J Diode AC
D511 RH-DX0441CEZZ J Diode AC
D632 RH-EX0630GEZZ J Zener Diode, 9.1V AA
D641 RH-EX0630GEZZ J Zener Diode, 9.1V AA
'åD651 VHD1SS244//-1 J Diode AB
å D653 RH-EX0667GEZZ J Zener Diode, 27V AA
å D661 RH-DX0468CEZZ J Diode AE
or
RH-DX0229CEZZ
or
RH-DX0302CEZZ
å D701 RH-DX0490CEZZ J Diode AC
or
RH-DX0154CEZZ
å D702 RH-DX0490CEZZ J Diode AC
or
RH-DX0154CEZZ
å D703 RH-DX0490CEZZ J Diode AC
or
RH-DX0154CEZZ
å D704 RH-DX0490CEZZ J Diode AC
or
RH-DX0154CEZZ
D705 RH-DX0048GEZZ J Diode AA
or
VHD1SS119//-1
D707 RH-DX0475CEZZ J Diode AB
or
VHD1SS244//-1
D708 RH-DX0475CEZZ J Diode AB
or
VHD1SS244//-1
å D709 RH-DX0229CEZZ J Diode AF
å D712 RH-DX0487CEZZ J Diode AC
or
RH-DX0302CEZZ
or
RH-DX0468CEZZ
or
RH-DX0487CEZZ
or
RH-DX0513CEZZ
D717 RH-EX0616GEZZ J Zener Diode, 5.6V AA
å D725 RH-DX0131CEZZ J Diode AC
D726 RH-DX0048GEZZ J Diode AA
or
VHD1SS119//-1
D740 RH-DX0048GEZZ J Diode AA
or
VHD1SS119//-1
D751 RH-EX0611GEZZ J Zener Diode, 5.1V AA
D752 RH-DX0441CEZZ J Diode AC
30
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
D753 RH-DX0441CEZZ J Diode AC
or
å D757 RH-DX0048GEZZ J Diode AA
å D758 RH-DX0131CEZZ J Diode AC
å VA701 RH-VX0019CEZZ J Varistor AC
å PR702 RMPTP0092CEZZ J Packaged Circuit AH
å L701 RCiLF0078PEZZ R Coil AF
å L702 RCiLF0078PEZZ R Coil (CU19M10) AF
å L705 RCiLP0179CEZZ J Coil AD
å T601 RTRNZ0731CEZZ J Transformer AG
'åT602 RTRNF0213PEZZ R H-Volt Transformer A Y
å T702 RTRNW0009PEZZ R Transformer AL
RH-DX0110CEZZ
or
VHD1SS119//-1
or (19U-M100, 19U-M100S)
RH-VX0035CEZZ
or
RH-VX0048CEZZ
PACKAGED CIRCUIT
X801 RCRSB0001PEZZ R Crystal AL
or
RCRSB0205CEZZ
FILTER AND COILS
CF2040
RFiLA0099CEZZ J Ceramic Filter AE
L50 VP-DF150K0000 J Peaking 15µH AB
L201 VP-XF1R2K0000 J Peaking 1.2µH AB
L202 VP-XF1R2K0000 J Peaking 1.2µH AB
L203 VP-XF220K0000 J Peaking 22µH AB
L204 RCiLi0632CEZZ J IF Coil AE
L301 VP-XF150K0000 J Peaking 15µH AB
or
RCiLF0069PEZZ
or
RCiLF0069PEZZ
L706 RCiLP0197CEZZ J Coil AE
L2040 RCiLB0131CEZZ J Oscillation Coil AE
SF201 RFiLC0441CEZZ J SAW Filter AH
TRANSFORMERS
or
RTRNZ0026PEZZ
or
RTRNW0003PEZZ
CONTROL
R738 RVR-M4588CEZZ+ R 22k(B) 130V Adj. AC
or
RVR-M4336CEZZ
CAPACITORS
[EL.··· Electrolytic, M-Poly..··· Metalized Polypro Film]
C51
VCEA0A1AW337M+
C53 VCEA0A1HW105M J 1.0 50V EL. AB
C54 VCEA0A1HW475M J 4.7 50V EL. AB
C55 VCEA0A1AW107M J 100 10V EL. AB
C101 VCEA0A1CW476M J 47 16V EL. AB
C201 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C202 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C203 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C204 VCQYTA1HM223K J 0.022 50V Mylar AB
C205 VCKYPA1HB103K J 0.01 50V Ceramic AA
C206 VCKYCY1HB102K J 1000p 50V Ceramic AA
C207 VCEA0A1CW476M J 47 16V EL. AB
C208 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C209 VCEA0A1HW105M J 1.0 50V EL. AB
C210 VCEA0A1HW474M J 0.47 50V EL. AB
R 330 10V EL. AC
C212 VCEA0A1HW474M J 0.47 50V EL. AB
C220 VCKYCY1CB104K J 0.1 16V Ceramic AB
C301 VCCCCY1HH220J J 22p 50V Ceramic AA
C302 VCKYCY1HB102K J 1000p 50V Ceramic AA
C304 VCCCCY1HH220J J 22p 50V Ceramic AA
C305 VCKYCY1HB103K J 0.01 50V Ceramic AA
C306 VCQYTA1HM103K J 0.01 50V Mylar AB
C354 VCEA0A1HW225M J 2.2 50V EL. AB
C356 VCKYCY1HB332K J 3300p 50V Ceramic AA
C357 VCEA0A1HW106M J 10 50V EL. AB
C358 VCEA0A1HW106M J 10 50V EL. AB
C361 VCEA0A1CW227M J 220 16V EL. AC
C401 VCCCCY1HH470J J 47p 50V Ceramic AA
C411 VCEA0A1AW108M J 1000 10V EL. AC
C412 VCKYCY1HB103K J 0.01 50V Ceramic AA
C414 VCEA0A1HW225M J 2.2 50V EL. AB
C416 VCEA0A1HW105M J 1.0 50V EL. AB
C418 VCKYCY1HB103K J 0.01 50V Ceramic AA
C421 VCEA0A1HW106M J 10 50V EL. AB
C451 VCQYTA1HM563K J 0.056 50V Mylar AB
C454 VCEA0A1HW475M J 4.7 50V EL. AB
C455 VCEA0A1CW226M J 22 16V EL. AB
C456 VCEA0A1HW475M J 4.7 50V EL. AB
C509 VCKYPA2HB102K J 1000p 500V Ceramic AA
C510 VCEA0A1VW477M J 470 35V EL. AB
C512 VCFYSA1JB224J+ R 0.22 63V Mylar AD
C513 VCFYSA1JB473J J 0.047 63V Mylar AC
C514 VCEA0A1EW477M J 470 25V EL. AD
C515 VCEA0A1HW475M J 4.7 50V EL. AB
C516 VCKYCY1HB222K J 2200p 50V Ceramic AA
C517 VCEA0A1CW226M J 22 16V EL. AB
C520 VCEA0A1HW107M J 100 50V EL. AB
C530 VCFYFA1HA334J J 0.33 50V Mylar AB
C531 VCFYFA1HA564J J 0.56 50V Mylar AB
C606 VCKYPA2HB561K J 560p 500V Ceramic AA
C607 VCKYPA1HB472K J 4700p 50V Ceramic AA
å C610 VCFPVC3ZA772H J 7700p 1.5kV M-Poly. AD
å C610 VCFPVC3ZA802H J 8000p 1.5kV M-Poly. AD
C612 VCFPVC2DB474J J 0.47 200V M-Poly. AE
C633
VCEA0A1AW337M+
C634 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C635 VCEA0A1HW105M J 1.0 50V EL. AB
C636 VCQYTA1HM153K J 0.015 50V Mylar AA
C637 VCEA0A1CW476M J 47 16V EL. AB
C652 VCEA0A1HW475M J 4.7 50V EL. AB
C653 VCEA0A1HW105M J 1.0 50V EL. AB
C661 VCKYPA2HB152K J 1500p 500V Ceramic AA
C662 VCEA0A1CW477M J 470 16V EL. AC
å C701 RC-FZ036SCEZZ J 0.1
å C705 RC-EZ1022CEZZ J 470 200V EL. AK
å C706 RC-KZ0092GEZZ J
or (19U-M100, 19U-M100S)
RC-FZ008SGEZZ
or
RC-FZ029CUMZZ
or
RC-FZ028SCEZZ
or
RC-FZ016SCEZZ
C702 RC-KZ0029CEZZ J 0.01
C703 RC-KZ0029CEZZ J 0.01
or
RC-EZ0609CEZZ 220 200V EL.
or
RC-EZ0629CEZZ 220 200V EL.
or
RC-KZ021SCEZZ
or
RC-KZ009SCEZZ
or
RC-KZ0106GEZZ
or
RC-KZ0156CEZZ
(19U-M100)
(19U-M100S, CU19M10)
R 330 10V EL. AC
AC250V
M-Poly. AC
AC250V
Ceramic AC
AC250V
Ceramic AC
0.0033
AC250V
Ceramic AC
31
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
å C708 RC-FZ037SCEZZ J 0.22 275V M-Poly. AD
or (CU19M10)
RC-FZ012SGEZZ
or
RC-FZ017SCEZZ
or
RC-FZ029SCEZZ
C717 VCKYPA2HB472K J 4700p 500V Ceramic AB
å C723 RC-EZ0638CEZZ J 33 160V EL. AG
å C725 RC-EZ0724CEZZ J 100 160V EL. AG
C726 VCKYPH3DB561K J 560p 2kV Ceramic AC
å C727 VCKYPA2HB472K J 4700p 500V Ceramic AB
å C730 VCEA0A1CW108M J 1000 16V EL. AD
å C731 VCEA0A1EW227M J 220 25V EL. AB
C732 VCKYPA1HF103Z J 0.01 50V Ceramic AA
C735 VCCCPA1HH680J J 68p 50V Ceramic AA
C737 VCEA0A1EW226M J 22 25V EL. AB
C738 RC-KZ0040CEZZ J 820p 2kV Ceramic AD
C739 VCEA0A1HW104M J 0.1 50V EL. AB
C740 VCEA0A1EW476M J 47 25V EL. AB
C743 VCKYPH3DB561K J 560p 2kV Ceramic AC
C750 VCKYPA1HF103Z J 0.01 50V Ceramic AA
C752 VCEA0A1CW476M J 47 16V EL. AB
C753 VCKYPH3DB561K J 560p 2kV Ceramic AC
(19U-M100, 19U-M100S)
C754 VCEA0A1CW476M J 47 16V EL. AB
C758 VCEA0A2EW106M J 10 250V EL. AD
C759 VCKYPA2HB102K J 1000p 500V Ceramic AA
C760 VCEA0A1CW108M J 1000 16V EL. AD
C771 VCEA0A1CW476M J 47 16V EL. AB
C772 VCEA0A1CW476M J 47 16V EL. AB
C783 VCQYTA1HM103K J 0.01 50V Mylar AB
C801 VCCCCY1HH180J J 18p 50V Ceramic AA
C802 VCEA0A1CW106M J 10 16V EL. AB
C807 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C808 VCEA0A1CW106M J 10 16V EL. AB
C809 VCEA0A1HW105M J 1.0 50V EL. AB
C811 VCKYCY1CB473K J 0.047 16V Ceramic AA
C812 VCEA0A1HW474M J 0.47 50V EL. AB
C901 VCEA0A1HW105M J 1.0 50V EL. AB
C905 VCEA0A1HW106M J 10 50V EL. AB
C2001 VCCCCY1HH101J J 100p 50V Ceramic AA
C2002 VCCCCY1HH101J J 100p 50V Ceramic AA
C2040 VCEA0A1AW107M J 100 10V EL. AB
C2041 VCEA0A1HW105M J 1.0 50V EL. AB
C2060 VCKYCY1CB104K J 0.1 16V Ceramic AB
C2061 VCKYCY1HB222K J 2200p 50V Ceramic AA
C2062 VCEA0A1AW107M J 100 10V EL. AB
C2201 VCKYCY1HB682K J 6800p 50V Ceramic AA
C2202 VCCCCY1HH560J J 56p 50V Ceramic AA
C2601 VCEA0A1HW475M J 4.7 50V EL. AB
C2602 VCCCCY1HH101J J 100p 50V Ceramic AA
RESISTORS
[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]
RJ2 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ4 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ5 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ7 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ8 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ9 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ10 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ12 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ16 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ18 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ19 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ20 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ21 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ28 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ29 VRS-CY1JF000J J 0 1/16W M-Ox. AA
å R53 VRS-VV3LB223J J 22k 3W M-Ox. AB
R54 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R55 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R56 VRS-CY1JF823J J 82k 1/16W M-Ox. AA
R57 VRD-RA2BE563J J 56k 1/8W Carbon AA
R101 VRD-RA2BE152J J 1.5k 1/8W Carbon AA
R201 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R202 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA
R203 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA
R204 VRS-CY1JF270J J 27 1/16W M-Ox. AA
R205 VRD-RA2BE680J J 68 1/8W Carbon AA
R206 VRD-RA2EE151J J 150 1/4W Carbon AA
R207 VRD-RA2BE223J J 22k 1/8W Carbon AA
R208 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R209 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R210 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R211 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R212 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R215 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R220 VRS-CY1JF331J J 330 1/16W M-Ox. AA
R301 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R302 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R353 VRD-RA2BE683J J 68k 1/8W Carbon AA
R354 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R355 VRD-RA2BE223J J 22k 1/8W Carbon AA
R357 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
R401 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R402 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R403 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R404 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R411 VRS-CY1JF684J J 680k 1/16W M-Ox. AA
R412 VRS-CY1JF391J J 390 1/16W M-Ox. AA
R413 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R414 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R421 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
å R451 VRS-SV2HC103J J 10k 1/2W M-Ox. AA
R453 VRD-RA2BE152J J 1.5k 1/8W Carbon AA
R454 VRD-RA2EE334J J 330k 1/4W Carbon AA
R455 VRD-RA2BE392J J 3.9k 1/8W Carbon AA
R456 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R457 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R458 VRD-RA2EE334J J 330k 1/4W Carbon AA
R460 VRD-RA2BE152J J 1.5k 1/8W Carbon AA
R461 VRS-CY1JF184J J 180k 1/16W M-Ox. AA
R462 VRS-CY1JF273J J 27k 1/16W M-Ox. AA
R495 VRS-VV3DB820J J 82 2W M-Ox. AA
R512 VRD-RM2HD102J J 1.0k 1/2W Carbon AA
R513 VRD-RM2HD102J J 1.0k 1/2W Carbon AA
R514 VRD-RM2HD1R0J J 1.0 1/2W Carbon AA
R515 VRS-VV3AB391J J 390 1W M-Ox. AA
R516 VRS-CY1JF153J J 15k 1/16W M-Ox. AA
R517 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R518 VRS-CY1JF333J J 33k 1/16W M-Ox. AA
R519 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R520 VRD-RM2HD1R2J J 1.2 1/2W Carbon AA
(19U-M100S, CU19M10)
R520 VRD-RM2HD1R5J J 1.5 1/2W Carbon AA
(19U-M100)
R522 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R523 VRD-RA2BE562J J 5.6k 1/8W Carbon AA
R525 VRD-RA2BE272J J 2.7k 1/8W Carbon AA
R527 VRD-RA2BE223J J 22k 1/8W Carbon AA
(19U-M100)
R528 VRD-RA2BE272J J 2.7k 1/8W Carbon AA
R529 VRD-RA2BE472J J 4.7k 1/8W Carbon AA
å R604 VRS-VV3DB682J J 6.8k 2W M-Ox. AA
R605 VRD-RA2BE121J J 120 1/8W Carbon AA
R606 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
å R607 VRS-VV3DB682J J 6.8k 2W M-Ox. AA
å R608 VRS-VV3DB391J J 390 2W M-Ox. AA
å R609 VRS-VV3AB562J J 5.6k 1W M-Ox. AA
R610 VRD-RM2HD220J J 22 1/2W Carbon AA
å R611 VRS-KA3HG3R3K J 3.3 5W M-Ox. AD
R622 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R623 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R624 VRN-RA2BK472F J 4.7k 1/8W M-Film AA
32
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
R634 VRD-RM2HD121J J 120 1/2W Carbon AA
R635 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R636 VRD-RA2EE221J J 220 1/4W Carbon AA
å R641 VRS-VV3AB682J J 6.8k 1W M-Ox. AA
å R651 VRD-RM2HD270J J 27 1/2W Carbon AA
å R653 VRS-CY1JF000J J 0 1/16W M-Ox. AA
å R654 VRD-RA2BE154J J 150k 1/8W Carbon AA
å R655 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
å R659 VRN-VV3AB2R2J J 2.2 1W M-Film AA
(19U-M100)
å R659 VRN-VV3ABR82J J 0.82 1W M-Film AA
(19U-M100S, CU19M10)
å R661 VRN-VV3ABR47J J 0.47 1W M-Film AA
å R662 VRD-RA2BE102G J 1.0k 1/8W Carbon AB
å R702 RR-DZ0049CEZZ J 3.9M 1/2W Carbon AB
or
RR-HZ0048CEZZ
or
VRD-UB2HG395K
å R703 VRW-KP3HC1R8K J 1.8 5W Cement AC
R705 VRN-VV3ABR39J J 0.39 1W M-Film AA
R706 VRN-VV3ABR39J J 0.39 1W M-Film AA
R707 VRD-RM2HD270J J 27 1/2W Carbon AA
R708 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R710 VRS-SV2HC102J J 1.0k 1/2W M-Ox. AA
R711 VRS-CY1JF334J J 330k 1/16W M-Ox. AA
R712 VRD-RA2BE100J J 10 1/8W Carbon AA
R713 VRS-SV2HC122J J 1.2k 1/2W M-Ox. AA
R715 VRD-RA2BE150J J 15 1/8W Carbon AA
R716 VRS-VV3AB121J J 120 1W M-Ox. AA
å R721 VRD-RM2HD124J J 120k 1/2W Carbon AA
R722 VRS-CY1JF225J J 2.2M 1/16W M-Ox. AA
R723 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R725 VRS-SV2HC821J J 820 1/2W M-Ox. AA
R733 VRD-RA2EE394J J 390k 1/4W Carbon AA
R736 VRD-RM2HD184J J 180k 1/2W Carbon AA
R739 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R740 VRD-RM2HD470J J 47 1/2W Carbon AA
R741 VRN-RA2BK682F J 6.8k 1/8W M-Film AA
R742 VRD-RM2HD561J J 560 1/2W Carbon AA
R743 VRD-RM2HD681J J 680 1/2W Carbon AA
R751 VRD-RA2BE821J J 820 1/8W Carbon AA
R752 VRD-RA2BE562J J 5.6k 1/8W Carbon AA
R755 VRD-RM2HD151J J 150 1/2W Carbon AA
å R758 VRS-SV2HC100J J 10 1/2W M-Ox. AA
å R773 VRS-VV3LB270J J 27 3W M-Ox. AB
å R774 VRS-VV3LB680J J 68 3W M-Ox. AB
R801 VRD-RM2HD470J J 47 1/2W Carbon AA
R807 VRS-CY1JF272J J 2.7k 1/16W M-Ox. AA
R808 VRS-CY1JF272J J 2.7k 1/16W M-Ox. AA
R809 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
R810 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
R901 VRD-RA2BE101J J 100 1/8W Carbon AB
R902 VRS-CY1JF750J J 75 1/16W M-Ox. AA
R906 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R925 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R961 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R962 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2001 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R2002 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2006 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2008 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA
R2009 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R2010 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R2012 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2016 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
R2018 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2020 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
R2022 VRS-CY1JF333J J 33k 1/16W M-Ox. AA
R2023 VRD-RA2BE223J J 22k 1/8W Carbon AA
R2024 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R2025 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R2026 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R2027 VRD-RA2BE682J J 6.8k 1/8W Carbon AA
R2028 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R2029 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2032 VRD-RA2BE471J J 470 1/8W Carbon AA
R2033 VRS-CY1JF684J J 680k 1/16W M-Ox. AA
R2034 VRS-CY1JF684J J 680k 1/16W M-Ox. AA
R2040 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R2041 VRS-CY1JF333J J 33k 1/16W M-Ox. AA
R2042 VRD-RA2BE101J J 100 1/8W Carbon AB
R2043 VRD-RA2BE101J J 100 1/8W Carbon AB
R2044 VRS-CY1JF683J J 68k 1/16W M-Ox. AA
R2045 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2047 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R2048 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA
R2049 VRS-CY1JF333J J 33k 1/16W M-Ox. AA
R2060 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R2061 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA
R2062 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R2063 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R2065 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R2066 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2067 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2068 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2070 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2072 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R2101 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2102 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2201 VRD-RA2BE103J J 10k 1/8W Carbon AA
R2202 VRD-RA2BE473J J 47k 1/8W Carbon AA
R2203 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R2211 VRD-RA2BE222J J 2.2k 1/8W Carbon AA
R2212 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA
R2213 VRD-RA2BE223J J 22k 1/8W Carbon AA
R2401 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2402 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2403 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2404 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R2501 VRS-CY1JF123J J 12k 1/16W M-Ox. AA
R2503 VRS-CY1JF273J J 27k 1/16W M-Ox. AA
R2504 VRS-CY1JF123J J 12k 1/16W M-Ox. AA
R2505 VRS-CY1JF563J J 56k 1/16W M-Ox. AA
R2506 VRS-CY1JF563J J 56k 1/16W M-Ox. AA
R2507 VRS-CY1JF823J J 82k 1/16W M-Ox. AA
R2508 VRS-CY1JF153J J 15k 1/16W M-Ox. AA
R2509 VRS-CY1JF272J J 2.7k 1/16W M-Ox. AA
R2601 VRD-RA2BE331J J 330 1/8W Carbon AA
SWITCHES
S2501 QSW-K0003AJZZ J POWER AB
or
QSW-K0079GEZZ
S2502 QSW-K0003AJZZ J VOL-Down AB
or
QSW-K0079GEZZ
S2503 QSW-K0003AJZZ J VOL-Up AB
or
QSW-K0079GEZZ
S2504 QSW-K0003AJZZ J CH-Down AB
or
QSW-K0079GEZZ
S2505 QSW-K0003AJZZ J CH-Up AB
or
QSW-K0079GEZZ
MISCELLANEOUS PARTS
å RY701 RRLYJ0081CEZZ J Relay AL
å F701 QFS-B4023CEZZ J Fuse, 4A/125V AC
or
QFS-B4021GEZZ
FH701 QFSHD1013CEZZ J Fuse Holder AC
FH702 QFSHD1014CEZZ J Fuse Holder AC
33
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A:DUNTKA358WEX9(19U-M100)
PWB-A:DUNTKA358WEY0(19U-M100S)
PWB-A:DUNTKA358WEY1(CU19M10)
MAIN UNIT (Continued)
FB351 RBLN-0091GEZZ J Ferrite Bead AB
or
RBLN-0047CEZZ
FB601 RBLN-0047CEZZ J Ferrite Bead AB
FB2002RBLN-0091GEZZ J Ferrite Bead AB
or
RBLN-0037CEZZ
J951 QJAKF0041CEZZ J Jack, A/V-In AH
P302 QPLGN0261CEZZ J Plug, 2-pin(S) AB
P401 QPLGN0561CEZZ J Plug, 5-pin(GBN) AB
P601 QPLGN0660CEZZ J Plug, 6-pin(K) AC
P651 QPLGN0361CEZZ J Plug, 3-pin(TP651-3) AB
P701 QPLGN0260CEZZ J Plug, 2-pin(M) AC
P751 QPLGN0461CEZZ J Plug, 4-pin(YBN) AB
P2001 QPLGN0561CEZZ J Plug, 5-pin(TP2001-5) AB
RMC2601
RRMCU0232CEZZ J R/C Receiver AG
or
RRMCU0252CEZZ
JA409 RBLN-0047CEZZ J Ferrite Bead AB
RDA501
PRDAR0297PEFW R Heat Sink, for IC501 AD
RDA602
PRDAR0216PEFW R Heat Sink, for Q602 AE
RDA701
PRDAR0026PEFW R Heat Sink, for Q701 AD
LX-BZ3100CEFD J Screw AA
PWB-B:DUNTKA359WEV2(19U-M100)
PWB-B:DUNTKA359WEV1(19U-M100S,
CU19M10)
CRT UNIT
TRANSISTORS
Q852 RH-TX0110BMZZ+ R TX0110BM AC
or
VS2SC2229O/1E
Q854 RH-TX0110BMZZ+ R TX0110BM AC
or
VS2SC2229O/1E
Q856 RH-TX0110BMZZ+ R TX0110BM AC
or
VS2SC2229O/1E
Q881 VS2SA1266-Y-1 J 2SA1266-Y AA
or
VS2SA1015-Y-1
DIODES
D882 RH-DX0048GEZZ J Diode AA
or
RH-DX0475CEZZ
D885 RH-DX0475CEZZ J Diode AB
or
RH-DX0048GEZZ
COIL
L852 VP-MK820K0000 J Peaking 82µH AB
CAPACITORS
[EL.··· Electrolytic]
C851 VCCCCY1HH151J J 150p 50V Ceramic AA
C852 VCCCCY1HH151J J 150p 50V Ceramic AA
C853 VCCSPA1HL151J J 150p 50V Ceramic AA
C854 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
or
RC-KZ0160GEZZ
C883 VCEA0A1CW336M J 33 16V EL. AB
RESISTORS
R851 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R852 VRD-RA2BE181J J 180 1/8W Carbon AA
R853 VRS-CY1JF121J J 120 1/16W M-Ox. AA
å R857 VRS-VV3AB123J J 12k 1W M-Ox. AA
R858 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R859 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R860 VRD-RA2BE181J J 180 1/8W Carbon AA
R861 VRS-CY1JF121J J 120 1/16W M-Ox. AA
å R865 VRS-VV3AB123J J 12k 1W M-Ox. AA
R866 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R867 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R868 VRS-CY1JF181J J 180 1/16W M-Ox. AA
R869 VRS-CY1JF121J J 120 1/16W M-Ox. AA
å R873 VRS-VV3AB123J J 12k 1W M-Ox. AA
R874 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R881 VRS-CY1JF561J J 560 1/16W M-Ox. AA
R882 VRS-CY1JF391J J 390 1/16W M-Ox. AA
R883 VRD-RA2BE561J J 560 1/8W Carbon AA
R884 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R886 VRS-CY1JF821J J 820 1/16W M-Ox. AA
R887 VRD-RA2BE470J J 47 1/8W Carbon AA
R890 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R891 VRS-CY1JF470J J 47 1/16W M-Ox. AA
[M-Ox.··· Metal Oxide]
(19U-M100S/CU19M10)
(19U-M100S/CU19M10)
(19U-M100)
(19U-M100)
MISCELLANEOUS PARTS
P851 QPLGN0561CEZZ J Plug, 5-pin(GBN) AB
P852 QPLGN0461CEZZ J Plug, 4-pin(YBN) AB
34
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-B:DUNTKA359WEV2(19U-M100)
PWB-B:DUNTKA359WEV1(19U-M100S,
CU19M10)
CRT UNIT (Continued)
SC851 QSOCV0016PEZZ R CRT Socket AF
or (19U-M100S/CU19M10)
QSOCV0933CEZZ
SC852 QSOCV0841CEZZ J CRT Socket (19U-M100) AG
or
QSOCV0840CEZZ
MISCELLANEOUS PARTS
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC6801PEZZ – Packing Case —
(19U-M100/100S)
SPAKC6802PEZZ – Packing Case(CU19M10) —
SPAKP0098PEZZ – Wrapping Paper —
SPAKX2701PEZZ – Buffer Material —
SSAKA0001PEZZ – Polyethylene Bag —
SUPPLIED ACCESSORIES
å
ACC701
QACCD3064CESA J AC Cord (AC120V/60Hz) AM
SP1 VSP0080PBQ9YA R Speaker, 32 ohm AH
or
VSP0080PBP8YA
or
VSP0080PBQ3YA
QCNW-0167MEZZ J Connecting Cord AE
QCNW-2046PEZZ R Connecting Cord AF
QCNW-2160PEZZ R Connecting Cord AG
LHLDK0014PEZZ R AC Cord Holder AD
LHLDZ0063PEZZ R Anode Clamp Holder AD
TLABM1829PEZZ R Model Label AB
TLABM1906PEZZ R Model Label(CU19M10)
TLABN0001PEZZ R Serial No. Label AD
LX-TZ0006PEFD R CRT Screw, x4 AD
LX-WZ0003PEFD R CRT Washer , x4 AB
PSPAG0001PE00 R CRT Spacer, x4 AB
XTASD30P12000 J Screw, x1 AA
XTASD40P20000 J Screw, x4 AA
LX-TZ3004CEFD Screw AA
TCAUH0008PEZZ J Caution Card AB
TCAUS0004PEZZ J Warning Label(CU19M10) AD
TCAUS0013PEZZ J Attention Label(CU19M10) AB
(19U-M100/100S)
(19U-M100/100S)
RRMCG1324CESA R Infrared R/C Unit AT
TGAN-0018PEZZ R Guarantee Card AD
(19U-M100/100S)
TiNS-7643PEZZ R Operation Manual AE
(19U-M100/100S)
TiNS-7644PEZZ R Operation Manual AN
(CU19M10)
35
19U-M100,19U-M100S
CU19M10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
CABINET PARTS CABINET PARTS LOCATION
1 CCABA2713WEV0 R Front Cabinet Ass’y BA
(19U-M100/100S)
1 CCABA2713WEV1 R Front Cabinet Ass’y BA
(CU19M10)
1-1
Not Available
– Front Cabinet —
1-2 GCOVA0069PEKA J LED Cover AD
1-3 JBTN-0243PESB R
Button(Power , V OL-Up/Down, AE
CH-Up/Down)
2 GCABB2477PEKA R Rear Cabinet AX
1-2
1-1
1
2
POWER
–
V
OL
+
C
H
M
E
N
U
1-3
36
★ Polyethylene Mat
PACKING OF THE SET
★ Polyethylene Bag
Operation Manual
Guarantee Card
(19U-M100/100S)
Batteries
★
Infrared R/C unit
★Buffer Material
19U-M100,19U-M100S
CU19M10
★ MARK : Not replacement items.
FRONT
★ Packing Case
REAR
Use 22 staples to
fix the bottom side
of packing case.
37
19U-M100,19U-M100S
CU19M10
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
D SEM P SREC TQ1282-S
Mar. 2002 Printed in Japan
MI. KG
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
38
Loading...