Sharp XL-530-H, CPXL-530-H Service manual

XL-530H,CP-XL530H

XL-530H micro component system consisting of
XL-530H micro component system and CP­XL530H speaker system.

SERVICE MANUAL

No. S5919XL530H//

XL-530H
CP-XL530H

• In the interests of user-safety the set should be restored to its original
condition and only parts identical to those specified should be used.

• Note for users in U.K.

Recording and playback of any material may require consent
which SHARP is unable to give. Please refer particularly to the
provisions of Copyright Act 1956, the Dramatic and Musical
Performers Protection Act 1956, the Performers Protection Acts
1963 and 1972 and to any subsequent statutory enactments and
orders.

CONTENTS

SAFETY PRECAUTION FOR SERVICE MANUAL .......................................................................................................... 2

IMPORTANT SERVICE NOTES (FOR U.K. ONLY) ......................................................................................................... 2

SPECIFICATIONS ............................................................................................................................................................ 3

NAMES OF PARTS .......................................................................................................................................................... 4

OPERATION MANUAL..................................................................................................................................................... 6

DISASSEMBLY................................................................................................................................................................. 7

REMOVING AND REINSTALLING THE MAIN PARTS.................................................................................................... 8

ADJUSTMENT.................................................................................................................................................................. 9

TEST MODE ................................................................................................................................................................... 10

NOTES ON SCHEMATIC DIAGRAM ............................................................................................................................. 15

TYPE OF TRANSISTOR AND LED ................................................................................................................................ 15

MEASURES TO BE TAKEN TO CHANGE THE MICROCOMPUTERS, STARTING FROM SERIAL No. 905xxxxx .... 15

BLOCK DIAGRAM .......................................................................................................................................................... 16

SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD............................................................................................ 20

WAVEFORMS OF CD CIRCUIT..................................................................................................................................... 27

TROUBLESHOOTING .................................................................................................................................................... 28

FUNCTION TABLE OF IC .............................................................................................................................................. 34

LCD SEGMENT .............................................................................................................................................................. 42

PARTS GUIDE/EXPLODED VIEW

PACKING METHOD (FOR U.K. ONLY)

Page

SHARP CORPORATION

– 1 –

This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

XL-530H,CP-XL530H

V

V

S

LCD701

LCD DISPLAY

8

9

6

7

4

321

5

15

161718

20

19

23 24

22

21

13

12

14

10

11

LED
D704~709
L1154GDA

CFW701

RESET

Q701

SWITCHING

Q702
Q703

SW700

JOG DIAL

RX701
REMOTE
SENSOR

KEY

C
A
B

N64H380A

SWITCHING

Q707

SW702~SW708
SW710~SW711
SW717~SW719

UP

DOWN

123

U-COM VDD
U-CON+5V
SYS STOP

REMOCON

RESET

P CONT

CNS681

A 12V
LED+B

SWITCHING

Q706

3
2
1

TO POWER PWB

X701
8MHz

X702

32.768KHz

Q705

SWTCHING

100

1
2

SEG0

SEG3

SEG1

SEG2

3
4

COM0

1

5

VLC3

2

VLC2

6

3

7

VLC1

8

VDD

9

OSC2

10

OSC1

11

VSS

12

XI

13

XO

14

MMOD

15

VREF

16

AREA
KEY1

17
18

KEY2

19

MODEL

20

VSM

21

F.P
RUN PLS

22

CAM SW+

23

VREF

24
25

DI

VDD1

VDD2

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 484950

CL

DO

SEG9

SEG8

SEG7

SEG6

SEG5

SEG4

COM3
COM2
COM1

SEG11

SEG10

SEG13

SEG12

SEG15

SEG14

SEG16

75
74
73

SEG17

SEG25
SEG26
SEG27

IC701

IX0015SJ

SYSTEM

MICROCOMPUTER

JOG UP

JOG DOWN

P-STB

CE

CLOCK

RESET

P-MUTE

P-CONT

CD+B

POWER

CLE

REMOCON

SYS STOP

ID

SEG18

DATA

SEG21

SEG20

SEG19

STEREO

SURROUND

CD STB

LID-SW

CD RES

CEE

BUCK

767778798081828384858687888990919293949596979899

SEG23

SEG22

SEG28
SEG29
SEG30
SEG31
SEG32
SEG33

SD

BUS3
BUS2
BUS1
BUS0

PU-IN

BIAS

B-CAN

REC
MOT

SOL

R-MUTE

LED_CONT

75
74
73

SEG24

72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

+5V

A_GND

TEST4

/TSMOD

+5V

X801

16.93MHz

DVSR

81

RO

82
83

DVDD

84

DVR

85

LO

86

DVSL

87

TEST1

88

TEST2

89

TEST3

90

BUS0

91

BUS1

92

BUS2

93

BUS3

94

VDD

95

VSS

96

BUCK

97

/CCE

98
99
100

/RST

123456789

D GND

XI

XVDD

XO

PXI

VSS

VDD

PXO

XVSS

TESIN

TESIO1

/CKSE

/DACT

IO3

/DMOUT

IO1

IO2

IC802

SERVO/SIGANL CONTROL

LRCK

TEST0

/HSO

EMPH

/UHSO

TC9462F

BCK

VSS

IPF

VDD

DOUT

SBOK DATA

MBOV

CLCK

VSS

AOUT

10 11 12 13 14 15 16 171819 20 21 22 23 24 25 26 27

IO0

SFSY

VSS

SBSY

VDD

SPCK

FLGD

SPDA

59606162636465666768697071727374757677787980

FLGC

COFS

FLGB

FLGA

MONIT

VDD

SEL

2VREF

P2VREF

TESIO0

FVO

DMO

VCOREF

ZDET

HSSW

FMO

TEZI

TSIN

SBAD

RFRP

RFZI
RFCT
AVDD

SLCO
AVSS
VCOF

PDO

28 29 30

5152535455565758

50
49

TEBC

RFGC

48
47
46

TEI

45
44
43

FEI

42
41
40
39
38

RFI

37
36
35
34
33
32
31

TMAXS

TMAX

VREF
TRO

FOO

PVREF

LPFO
LPFN

+5V

FOCUS/TRACKING/
SPIN/SLIDE DRIVER

D GND

+5V

Q801

IC804

LA6541D

IC801

SERVO PRE AMP.

TA2109F

S+7.5V

SBAD

RFRP

RFGC

REG IN

REG.

RESET

RES

16 17 18 19

FEI

RFI

VIN2

REG OUT

CD

VIN3

TRO

SBAD
FEO

14

FEN

15

VRO

16
17

RFRP

18

RFIS

19

RFGO

20

RFGC

21

AGCI

22

RFO

23

GND

24

RFN

SL+

SL–

FMO

101112131415

8

9

Vo3

Vo4

VG2

GND

GND

+

––

–

+
+

–

+

–

VG3

Vo5

GND

Vo6

GND

20 21 22

2324252627 28 29 30

TR+

TR–

TEO
TEN

2VRO

TEB
SEL

LDO

MDI
TN1

TPI
FPI

FNI

VCC

7

GND

GND

TEI

1213
11
10

TEBC

9

SEL

8
7
6

E

5

F

4

B

3

A

2
1

CD +5V

SP+

SP–

6

5

Vo1

Vo2

VG1

+

–

+

+

–

+

–

Vo8

VG4

Vo7

FO+

FO–

S+7.5

DMO

CD STB

1234

VIN1

VCC

MUTE

+

–

Vref

VIN4

VCC

S+7.5

FOO

+5V

D GND

Figure 16 BLOCK DIAGRAM (1/4)

– 16 –

XL-530H,CP-XL530H

SEG14

CLE

15

161718

SEG17

SEG25
SEG26
SEG27

ID

SEG19

SEG18

SURROUND

DATA

CD RES

19

SEG21

SEG20

STEREO

CD STB

CEE

BUCK

20

21

SEG22
SEG28
SEG29

SEG30
SEG31
SEG32
SEG33

BUS3
BUS2
BUS1
BUS0

PU-IN

LID-SW

BIAS

B-CAN

REC
MOT

SOL

R-MUTE

LED_CONT

13

14

6

SEG16

SEG15

75
74
73

J

M

UTER

JOG UP

JOG DOWN

041424344454647484950

22

76777879808182838485

SEG24

SEG23

SD

23 24

75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

CFW702

SW701
CD EJECT

RECORD/

PLAYBACK

HEAD

L-CH

R-CH

ERASE

HEAD

CNP101

8

8

7

7

6

6

5

5

4

4

3

3

2

2

1

1

L-CH
L-CH
A_GND
A_GND
R-CH
R-CH
ERASE
A_GND
M 12V
D GND
VDO
CL
DO
CE
DI

CNS603

1
2
3
4
5
6
7
8
9

10
11
12
13
14
15

TO MAIN PWB

BIAS

1

B-CAN

2

REC

3

SD

4

FM ST

5

R-MUTE

6

CD+B

7

P-STB

8

A 12V

9

P MUTE

10

L-CH

11

R-CH

12

A GND

13

S+6.2V

14

M GND

15

CNS602

S+7.5V

1

VIN2

REG IN

G/

REG OUT

REG.

ER

RESET

RES

CD

VIN3

16 17 18 19

TRO

IC801

PRE AMP.

2109F

SBAD

SBAD

FEI

FEO

14

FEN

15
16

VRO

RFRP

17

RFRP

18

RFIS

RFI

19

RFGO

RFGC

20

RFGC

21

AGCI

22

RFO

23

GND

24

RFN

SL+

SL–

FMO

101112131415

8

9

Vo3

Vo4

VG2

GND

GND

+

––

–

+
+

–

+

–

VG3

Vo5

GND

Vo6

GND

20 21 22

2324252627 28 29 30

TR+

TR–

1213

TEO

11

TEN

10

2VRO

TEB

9

SEL

8

LDO

7

MDI

6

TN1

5

TPI

4

FPI

3

FNI

2

VCC

1

SP–
6

7

Vo2

GND

–

GND

Vo7

FO–

TEI

TEBC
SEL

E
F
B
A

CD +5V

DMO

SP+
5

Vo1

VG1

VIN1

+

–

+

+

–

+

VIN4

Vo8

VG4

FO+

FOO

S+7.5V

CD STB

1234

VCC

MUTE

+

–

Vref

VCC

S+7.5V

SWITCHING

Q801

+5V

VREF

+5V

CNS803

CNS801

CNS802

6
5
4
3
2
1

1
2
3
4
5
6
7
8

1
2
3
4
5
6
7

CNP803

SP+

6

SP–

5

SL+

4

SL–

3

PU-IN

2

GND

1

TR-

1

TR+

2

FO+

3
4

GND

5

PD

6
7
8

C

1

F

2

B

3

A

4

E

5

1/2V

6

+5V

7

FO–

VR
LD

+

M802
SPINDLE MOTOR

M

–
+

M801

M

SLED MOTOR

–

SW801
PICKUP IN

PICKUP UNIT

MOT

LT0H41M1

1/2VCC
C
F
B
A
E
GND
MON
LD
VCC

SOL

Q903

TR+
FO+
FO–
TR–

ACTUATOR

RUN PLS

SWTCHING

M GND

TAPE MOTOR

6

5

7

6

5

7

PH901

PHOTO

INTERRUPTER

U-CON5V

Q906

SWTCHING

DRIVER

Q905

Q902

SOLENOID

DRIVER

P.F

234

1

234

1

SW901
FOOL PROOF

M+12V

CAM SW
CNS901

CNP901

Q904

SWTCHING

Q901

SWTCHING

CFW901

TAPE MOTOR

+

M901

M

SW902
CAM

–

SOL901

SOLENOID

Figure 17 BLOCK DIAGRAM (2/4)

– 17 –

XL-530H,CP-XL530H

FM/AM LOOP

CNP301

AM

FM

ANTENNA

1
2 1 2
33

T302

AM ANT.

T306

AM OSC.

VD301-1

VD301-2

FM MUTE

LEVEL

VR351

10K(B)

AM OSC OUT

AM OSC IN

AM OSC OUT

AM MIX OUT

FM IF IN

FM AFC

REG

AM RF IN

VSM

AM IF IN

4 3 2 1

GND

5

AM LOW CUT

SD

6

FM/AM OUT

STEREO

FM DET

8

7

X351
VCO

MPX VCO

VCC

10 11 12

9

MPX IN

PHASE

IF OUT

L-CH OUT

R-CH OUT

131415161718192021222324

MO/ST

FM MPX./AM IF

PHASE

(AM/FM)

SWITCHING

Q351

IC303

LA1832

FM IF DET./

R-MUTE

BF301
BAND

PASS
FILTER

CNP603

L-CH

1

L-CH

2

A-GND

3

A-GND

4

R-CH

5

R-CH

6

ERASE

7

A-GND

8

M_12V

9

D_GND

10

TO CD SERVO PWB

VD0

11

CL

12

D0

13

CE

14

DI

15

FM RF

L302

VD303

FM FRONT END

VT

IC301

TA7358AP

FM IF FM IF

FM OSC

L303

VD302

78654323211

9

A-12V

SWITCHING

Q305

CF303 T304

VT

HEAD SELECTOR

BA3126N

REC SW

1
2
3

P/B SW
CONT

4

5

6

P/B SW

7
8
9

REC SW

Q171

Q172

SWITCHING

FM IF AMP.

IC101

Q609

REC

Q306

Q154
Q155

BEAT CANCEL
SWITCHING

B-CAN

FM IF
CF302

10.7MHz

X352

4.5MHz

PLL CONTROLLER

SWITCHING

Q101-Q104

Q151
L151

BIAS OSC

AM IF

T351

AM MIX OUT

D GND

22 20 19 18

21

X OUT
X IN

1 2 3 4

IC302

LC72131

Q152

Q153

REC BIAS

VT

TP301

VSS

AOUT

NC

SWITCHING

A–12V

SWITCHING

CONT

1 3

CF352

CE

AM IF IN

FM IF

CF351

PD

AIN

DI

DO

CL

6

5

REC

PLAYBACK AND RECORD/

L-IN

R-IN

VCC

+5V

13 1215 1417 16

SW

NC

VDD

AM IN

FM IN

MO/ST

FM

MW

FM

8

9

7

10 11

IC102

PLAYBACK AMP.

BA3311L

NF

3

5

150K
–
+

MUTE

+
–

9

150K

11

NF

IF INIF REQ

IC102

ALC

6

REC R-CH

L-OUT

7

ZD351

+5V

1

A+12V

8

10

2
ALC

12

R-OUT

A-GND

REC MUTE

L-CH

SWITCHING

R-CH

A–12V

FM+B

FM RIPPLE
FILTER

Q105
Q106

Q107

Q360

REC

Figure 18 BLOCK DIAGRAM (3/4)

– 18 –

ITCHING
Q351

2
ET./

M IF

A–12V

R-MUTE

R-MUTE

IC401

AUDIO PROCESSOR

M62495FP

XL-530H,CP-XL530H

FM+B

M RIPPLE
ILTER

TE

Q105
Q106

ITCHING

Q107

Q360

REC

STEREO

SD

REC R-CH

TAPE L

BIAS

1

-CH

REC

B-CAN

SD

FM ST

2 3 4

5

TO CD SERVO PWB

CD+B

R-MUTE

6

7

P-STB

8

A 12V

10

9

P MUTE

CD L

11 12

CD R

A_GND

S+6.2V

13 14 15

M-GND

CNP602

VOLTAGE REGULATOR

CD+6.2V

REGULATOR

MECH 12V

(M 12V)

VOLTAGE

REGULATOR

AUDIO 12V

(A 12V)

Q607

VOLTAGE

Q605

Q604

CD

TAPE

Q606

MUTE

Q608

Q601
Q602

CD+B

TUNER

Q609

Q603

GND

STAND-BY

D601

T800mA L 250V

CD L-CH

TUNER L-CH

IC601

POWER AMP.

LA4600

L-IN

10

8

R-IN
FILT

5

GND

9

6

P.P

VCC

7

4

F653

GND

FROM
LED
PWB

CD R-CH

TUNER R-CH

INB2

INC2

INA2

IC401

INA1

INB1

INC1

1 2 3 4

TAPE L-CH

L-CH OUT

1

0V

2

GND

R-CH OUT

3

CNS652

CNP652

2 2

1 1

GND

CNP681

3
2
1

TAPR R-CH

21222324

20

IND2

INE2

IND1

INE1

5

D651~D654

VOLTAGE REGULATOR

Q683

Q682

D681~D684

REC R-CH

VOLIN2

SELOUT2

SELOUT1

6

7

REC L-CH

TONEH2

VOLIN1

8

TONEH1

L-CH OUT

Q681

R-CH OUT

TONEL2

OUT2

OUT1

9

10 11 12

TONEL1

L-CH

R-CH

F651

T2.5A L 250V

T681

SUB POWER

TRANSFORMER

GND

13141516171819

VSS

CONT

LOGIC

VDD

GND

VCC

1/2VCC

SO601
SPEAKER
TEMINALS

J601
HEADPHONES

MAIN POWER

TRANSFORMER

RLY681

T651

T.F

AC POWER

INPUT SOCKET

AC230V,50Hz

SO651

A 12V

5V

Q401

LF651
LINE
FILTER

Figure 19 BLOCK DIAGRAM (4/4)

– 19 –

XL-530H,CP-XL530H

C
4

R

R114

0

A

B

C

D

E

F

G

FM/AM
LOOP
ANTENNA

AM

FM

CNS603

P23 12-A

TO CD SERVO PWB

CNP301

1
2 1 2
33

BAND PASS

CNP603

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

R320 33

AM ANTENNA

C302

0.001

D301

1N4148

D302

1N4148

1

BF301

FILTER

C349

0.022

D306

1N4148

2

L-CH

L-CH
A-GND
A-GND

R-CH

R-CH
ERASE
A-GND
M_12V
D_GND
VDO
CL
DO
CE
DI

C337

0.022

C305

0.0047
C307

0.0047

C308

0.022

C304

0.01
FM RF

C306

7P(UJ)

D305

IN4148

C397

0.022
(CH)

3

123 4 56 7 8 9

0.8V

1.5V

M_12V

D_GND

VDOCLDOCEDI

VD301-1

KV1236Z23F

T302

C330
8P(UJ)

AM TRACKING fL

R321
22

AM OSC.

KV1236Z23F

T306

R323
68K

AM BAND COVERAGE fL

Q305
2SC535 C

C309

0.001

R301

2.2

R303 33K

L302

R302 100K

VD303

KDV147C

C303

0.001

C318
5P

0V

5.2V

5.2V

1.5V

FM FRONT END

TA7358AP

VD301-2

C334
18P
(UJ)

R315
33

0.8V
R304

47K

FM BAND
COVERAGE
fL

FMIF
T304

C311
10P(CH)

IC301

C121
82P

C131

C331

0.047

R310

4.7K

FM OSC

820P

R319
100K

C335
18P
(CH)

0V

2.4V

4.4V

C122
82P

C332

0.022

C315

100P

R305
680

L303

C312
33P

R307
47

R306

10

3.8V

C101

0.001
R140

10K

R139

2.7K

C102

0.001

(11.7V)

2

Q171

KRA102 M

SWITCHING

C333

0.022

R324
100K

C336
470P

R336

4.7K

C316

10/16

C317

C314
22P(CH)

C313

3.3P(UJ)
VD302

CF303
FM RF

10.7MHz

123

HEAD SELECTOR

R101
1K

0V
0V
0V

0.3V
(8V)

0V

2.8V
0V
0V

R138
330

0V

R102

+B

1

11.7V
(0V)

3

Q172

KRC102 M

2

11.7V
(0V)

1

0V

0.022

R308

10K

KDV147C

5.2V

1
2
3
4
5
6
7
8
9

1K

0V
3

R314

33

FM

R313 680

IF
AMP.

0.1V

0.7 V

R312

2.2K

R309
470

IC101

BA3126N

REC SW

P/B SW
CONT

P/B SW

REC SW

C151
180P
C152

0.001

Q154

KTC3199 GR

Q155

C156

0.022

KTC3199 GR

Q154,Q155:
BEAT CANCEL
SWITCHING

AUTO-STOP

R351

5.6K

C323

0.022

Q306

2SC535 C

1V

R311

330

C153

0.0039
(P.P)

R159

5.6K

0.7V

R160

(0V)

5.6K

0.7V
(0V)

VR351
10K(B)

FMRF

C351

0.022

CF302

10.7MHz

VDO
M_12V
D_GND

Q101~Q104:SWITCHING
Q101

KTC3199 GR

C113

4.7/25

R126

5.6K

KTC3199 GR

C114

4.7/25

R151
47K

C154

0.027
(ML)

FM MUTE
LEVEL

1

2

+B

0.3V
(0.8V)

Q102

0.3V
(0.8V)

R122

4.7K

C117
10/16

2.6V(0V)
Q151

2SC2001 K

L353
1mH

3

R152
100K

L151
330µH

DO
CL
DI
CE

R121

4.7K

C343

33P

R358

8.2K
C361

0.022

C362

3.3/50

C360

0.022

5V

3.5V

AM OSC IN

AM OSC OUT

AM MIX OUT

FM IF IN

2.1V

5V

+B

R382
330

R386

TP301

330

VT

2.6V

C381
12P(CH)

X352

4.5MHz

C382

1 2 3 4

15P(CH)

2.6V

IC302

LC72131

PLL CONTROLLER

C384

0.001

Q103

1.5V

KTC3199 GR

(0V)

0.3V
(0.8V)

R123

R119

4.7K

100

Q104

1.5V
KTC3199 GR

(0V)

R118
22K

0.3V
(0.8V)

R124

4.7K

R125
100K

R120
100

7.8V
(0V)

+B

7.8V
(0V)

SWITCHING

C155

4.7/25
Q153

KRC104 M

REC BIAS CONT

C116

0.0022

R116
15K

Q152
KTA1266 GR

8.3V
R154

10K

R153
10K

2

1

C363

0.022

C364

10/16

2.1V(2.7V)

2.1V

(2.7V)

0.6V

2.1V

0.022

R115
15K

C130

4.7/25

4.7V
(0V)

C350

AM IF

T351

VSS

0V

R117
22K

R155

AM RF IN

CF352
AM IF

0.022

C394
47/16

R381
10K

C393
1/50

AOUT

56

VSM

AM IF IN

4 3 2 1

2.1V

R352
1K

3

1

2

C392

0.001

R380

1.5K

0.9V

AIN

0.1V

R3731KR3721KR371

R374

1K

R157
150

R156
150

5

0V

0.1V

C129

4.7/25

GND

C353

C380

0.9V

C106
270P

C103
330P

PD

FM AFC

REG

C397

X OUT
X INNCCEDICL

C115

0.0022

3

C366

0.001

C365

0.022

0V(0.9V)

2.3V

FM/AM

FM MPX./AM IF

AM LOW CUT

SD

6

7

5V

5V

0.022

1/50

C387

0.022

R379

2.2K

5.2V

VDD

DO

6

5

4.8V

5.1V

1K

R103
120

C107
47/16

C105
270P

5

0V

C104

330P

9

0V

C108

R104

47/16

120

+B

TP302

R350

X351

2.7K

456kHz
VCO

C367
1/50

IC303

OUT

LA1832

FM IF DET./

STEREO

FM DET

8

R353
270

2.9V(4.3V)

CF351

FM IF

C354

0.022

C399

0.022

C385

0.01

L351

100µH

2.6V(0V)

0V(2.6V)

0V

NC

AM IN

FM IN

FM

MW

FM

9

10

8

7

0V

3.9V

3.7V(0V)

1.7V(11.4V)

R107

0.015(ML)

10K

BA3311L

PLAYBACK AND

RECORD/

PLAYBACK AMP.

0.6V

3

150K
–
+

MUTE

+
–

150K

11

0.6V

R108
10K

2.3V

(0V)

VCC

9

5V

C398

+B

R393

R377

5.6K

3.5V

0V

12131415202122 1618 1719

SW

IF IN

IF REQ

MO/ST

11

R359

1.8K

R105
150K

C109

IC102

6

C110

0.015(ML)

R106
150K

IC102

R357

470K

C369

R356

1K

C368

1/50

2.1V

MPX IN

MPX VCO

PHASE

IF OUT

10 11 12

0V

3.8V

(1.9V)

C357

2.2/50

100/10

C356

0.001

C355

22P

R395

47K

1K

C386
330P

R365
10K

R360

4.7K

+B

R109

3.9K

1

ALC

12

7

0V 0V

R110

3.9K

C374

56P

1.3V

R-CH OUT

C358
1/50

C370
1/50

R387

R127

3.9K

C111

10/16

4.6V

4.6V
C112

10/16

R128

3.9K

R355

3.3K

0.015

5.6K

8

10

2

C373

C371
1/50

C372
1/50

4V
(2.2V)

131415161718192021222324

MO/ST

L-CH OUT

PHASE

(AM/FM)

R376

10K

C383

0.022

R129

3.3K

D101
1N4148

10.2V
0V

(10.1V)

0V

C124

47/16

R130

3.3K

REC MUTE

0.015

R361
12K

R362
12K

3.8V(1.2V)

+B

C119

C123

D102

1N4148

C120

0.01

R364

L352
100µH

R391
390

R392
390

0.01

2.2/50

6.8K

R363

6.8K

4.7V
(0V)

SWITCHING

Q105
KTC3199 GR

C126

22/16

C118

0.022

R135

680K

Q107
KRC104 M
SWITCHING

Q106

KTC3199 GR

1

2

ZD351

MTZJ5.1B
C396

100/10

C395

0.022

Q360

KTA1266 GR

VDO
M_12V

D_GND

R111

2.2K

REC MUTE

R131

4.7K

0.7V

R133

R134

100K

1K

R141
330

C125

100/25

2

1

R112

2.2K
R132

4.7K
D104

0.7V

1N4148

11.7V
R383

5.6K

R384

6.8K

0.2V

3

R136

Q351

3

(7.1V)

10K

KRC104 M

1

5

D105

1N4148

H

• NOTES ON SCHEMATIC DIAGRAM can be found on page 15.

1

23456

Figure 20 SCHEMATIC DIAGRAM (1/4)

– 20 –

7

8 9 10 11 12

R134

C125

7V

V)

2
ITCHING

1

Q351

KRC104 M

3

XL-530H,CP-XL530H

MAIN PWB-A1

FM SIGNAL

AM SIGNAL

PLAYBACK SIGNAL

RECORD SIGNAL

CD SIGNAL

ZD351

MTZJ5.1B
C396

100/10

C395

0.022

Q360

KTA1266 GR

11.7V

R383

5.6K

R384

6.8K

VDO
M_12V
D_GND

R111

2.2K

EC MUTE

R131

4.7K

0.7V

105

C3199 GR

R133

100K

1K

R141
330

100/25

0.2V

3

1

M
NG

R136

R112

2.2K
R132

4.7K

D104

.7V

1N4148

6
9 GR

(7.1V)

10K

D105

10.8V

10.9V
R385

5.6K

C391
47/16

1N4148

FM RIPPLE
FILTER

+B

REC L
REC R
TAPE R
TAPE L

R113

R114

3.3K

C406
10/16

C404
10/16

C402
10/16

2.4V

IC401

M62495FP

CD R

TAPE R

TUNER R

R-MUTE

+B

FM+B

A GND
STEREO

SD
A 12V

+B

D GND

3.3K

+B

R137

4.7K

D106

1N4148

+B

R-MUTE

FM ST

SD

REC

B-CAN

CNP602

BIAS

1

2 3 4

CD+B

6

5

7

TO CD SERVO PWB

P23 12-B

P-STB

8

CNS602

A 12V

CD R

CD L

P MUTE

10 11 121314 15

9

A-GND

AUDIO PROCESSOR

R634
1K

C388

0.001

CD(6.2V)
CD-DSP

+B

CD P-OPE.

TO TRC MOTOR

+B

A_12V
TO TUN

TO TAPE EQ
TO A-PROC.

M-GND

S6.2V

CD L
TUN L
TAPE L

C628

TO µ-COM

C401
10/16

C403
10/16

C405
10/16

R601
10K

C601
33/16

R602
10K

R608
1K

Q603~Q609:VOLTAGE REGULATOR

C627

0.022

R627

10K

10/16

M_12V

C625

10/16

A_12V

C623

10/16

C622

R615
390

0.022

D604

C626

C624

R621

R607

R616

6.2V

1N4148

47/16

0.022

22K

R415

R423

6.8K

390

2SD2012 Y

R623

D603

C621

R428

R424

47K

R426

47K

R418

1.5K

R420

R416

1.5K

2.5V

2.4V

24 23 22 21 20 19 18 17 16 15 14 13

INC2

INB2

INA2

MUTE

INPUT

MONOPHONIC SW

INA1

INB1

INC1

1 2 3 4

2.4V

2.4V

2.4V

1.5K

R419

R417

1.5K

R427

47K

R425

47K

47K

C605

0.047

R603
1K

Q601

MUTE

0.7V
(0V)

KTC3199 GR

R604
1K

Q602

MUTE

0.7V
(0V)

KTC3199 GR

C606

0.047

D601
1N4148

Q607

19.6V

6.9V

Q606

KTC3199 GR

7.5V

R625

ZD602

10K

MTZJ7.5C

12.4V

22K

Q604

2SD2012 Y

11.8V

19.6V

12.4V

R620

D602

1N4148

47

1N4148

R617

33K

100/25

47K

1.5K

0V

IND2

5K5K

IND1

0V

1.5K

C604

0.001

+B

KRA102 M

ZD601

MTZJ13A

C416
10/16

2.4V

INE2

VOLUME

INE1

5

2.4V

C415
10/16

C603

0.001

Q608

2

7.5V
Q609

KRC107 M

19.6V 11.9V
Q605

2SD2012 Y

R619
47

Q603

KTC3199 GR

13.0V

14dB14dB

2.4V

C697

0.001

R436
10K

2.4V

6

R435
10K

7.8V
1

19.6V
R628

100

R438

6.8K

2.4V

VOL IN2

SEL OUT2SEL OUT1

30K

30K

VOL IN1

7

C417

10/16

R437

6.8K

1.4V

9.5V

C607
100/25

C608
22/25

12.9V

1.4V

STAND-BY

R624
1K

3
0V

3

C620
470/25

C420

C418

TREBLE

TONEH1

2.4V

C419

0V

0V

2

C426

10/16

R440

2.2K

R442

390

0.033

C424

C431

100P

0.22

10/16

C422

0.22

2.4V

2.4V

2.4V0V2.7V

TONEL2

46K

21.6K

+

TONEH2

+

–

–

2.4K

2.4K

+

+

–

–

21.6K

BOOST

46K

8

9

2.4V

2.4V

C421

0.22

0.033

R439

2.2K

IC601

LA4600

POWER AMP.

10

5

9

6

8

7

1.7V

OUT2

BUS BOOST

OUT1

10 11 12

2.4V

TONEL1

C423

0.22

R441

390

C425

10/16

VCC

4

20V

C699

0.001

C615

0.022

CONT

VSS

CONTROL LOGIC

VDD

GND

4.8V

2.4V

9.8V

1

0V

2

C614
1000/25

3

9.8V

C616
4700/25

C430

470/10

C613
1000/25

R449
10K

R443
12K

R444
220

R445
220

R450

C432

R453
220

2.2K

R452

Q401

220

2SD468 C

R446

0.022
C433

100/10

C428

47/16

+B+B

L-CH

L-CH

A_GND

R-CH
R-CH

POWER PWB-B

D651

F653

T800mA L 250V

1

4.5V

+B

FROM LED PWB

R629

820

When servicing,pay attention as the area enclosed
by this line( )is directly connected with AC
main voltage.

CNP681

3
2
1

P22 3-E

CNS681

CNP653

C695

0.001

CNP652

2

2

1

1

Q681~Q683:
VOLTAGE
REGULATOR

Q683

KTC3199 GR
R685
10K

R686
47K

C683

2200/16

C660

0.01

C696

2 1

BI652

CNS652

C652

2
1

C653

0.2V

(5.2V)

0.8V
(0V)

0V

C689

D681~D684:1N4004

D682

D683

0.01

D652

0.1

D653

D654

0.1

D651~D654:1N4004

Q682

2SD468 C

9.0V

4.9V

R684

1.2K

5.6V

R683

47

47/16

ZD682

MTZJ5.6B

R680

1

D681

C681

0.047
C682

0.047

D684

5.8V

C686

C434
1/50

+B

7.5V4.8V

R447

82

5.5V

ZD401

R448
220

R451
220

CNW601
5

1

C651

0.1

C654

0.1

Q681

2SD468 C

9.0V

6.4V

R681

47

0.022

ZD681

MTZJ6.8A

T681
SUB POWER
TRANSFORMER

470

MTZJ5.6B

L-CH

SO601

GND

SPEAKER

GND

TERMINALS

R-CH

HEADPHONES
PWB-A2

R662
330

R661

5

1

T2.5A L

330

MAIN POWER TRANSFORMER

F651
250V

D685
1N4004

C688

0.022

R682

1.2K
C684

0.047

C685

47/16

LF651

LINE

FILTER

INPUT SOCKET

T651

T.F

RLY681

SO651

AC POWER

AC230V,50Hz

J601
HEADPHONES

Figure 21 SCHEMATIC DIAGRAM (2/4)

– 21 –

XL-530H,CP-XL530H

E

W

S

V

6

LED PWB-A3

A

B

1

1

C

D

+B

82

R703A

D707

82

R703B

D708

82

R703C

D709

D704~D709:L1154GDA

2

CFW701

2

1K

D720

R70B

1N4148

R70A

4.8V

1K

Q701

KRC102 M

RESET

C710

0.01

SWITCHING

KTA1266 GR

+B

10.7V

R702A

R702B

R702C

2

Q707

82

D704

D705

82

D706

R70C

3.3K

SW717
BASS/

TREBLE

R714
27K

R715
10K

R716

5.6K

R717

SW711

REWIND

SW710

FAST

FORWARD

CLOCK/

TIMER/

SLEEP

SW719

SW718

ON/

STAND-BY

UP

DOWN

ZD701

MTZJ3.3B

R70K

120

1.1V

C704

0.022

R70L

1K

C707

4.7/25

R70M 100

P CONT

C713

10/16

3.9K

R718

2.7K

R719

1.8K

R720

1.8K

R721

SENSOR

32

82

C705

0.001

SW700

JOG DIAL

C
A
B

C706

0.001

C711

Q702

3.3/50

KTC3199 GR

3

1

4.9V

C712

0.01

D721

1N4148

R70E

100K

R70F
82

10.9V
R798

10V

47K

R799

2.2K

0.35V
R70J

10K

0.34V

SWITCHING

Q706

KRC102 M

2

1

R70G

1K

KTC3199 GR

SWITCHING

3

4.4V

Q703

+B

R70H
10K

10K

RX701

REMOTE

RECORD PAUSE/

10K

R769

1

C714
560P

SW708

BEAT CANCEL

SW707

MEMORY/

SET

SW706

BAND

SW705

FUNCTION

SW704

STOP

SW703

PLAY

SW702
VOLUME/
JOG DIAL

R713

R722

10K

10K

µ-COM VDD
µ-CON+5V

SYS STOP
REMOCON
RESET

D722
1N4148

D723
1N4148

C715
100/10

R707
10K

R708

5.6K

R709

3.9K

R710

2.7K

R711

1.8K

R712

1.8K

L701

LCD701
LCD DISPLAY

2.5V

2.5V

2.5V

2.5V

1234

100
1
2

SEG0

SEG1

R725

X701
8MHz

R736
47K

R737
47K

R738
47K

3

COM0

4

47K

0V

VLC3

5

1.7V

VLC2

6

3.3V

VLC1

7

4.9V

VDD

8

2.6V

OSC2

9

2.4V

OSC1

10

0V

VSS

11

1.9V

XI

12

2.3V

XO

13

0V

MMOD

14

22P

0V

(CH)

C702

VREF

15

1.6V

AREA

16

5.0V

KEY1

17

5.0V

KEY2

18

0V

MODEL

19

VSM

20

0V

F.P

21

0V

RUN PLS

22

5V

23
24
25

DO5VCL0VVDO10VVD02

26 27 28 29 30 31 32 3334 3536 3738 39 40 41 42 43 44 45 46 47 48 49 50

0V

R743

R742

R741

R745

R746

R744

0V

R735

47K

+B

R724
47K

R726

1K

C703

0.022

100µH

+B+B

R723

47K

C701

22P(CH)

R727

4.7K

+B
R741~R746,

R749~R757:1K
R759~R761:1K

SWITCHING

4.8V

R734

47K

X702

32.768kHz

R728 1K
R730 1K
R731 1K
R732 1K

R729
10K

Q705

KRA102 M

3

1

4.9V

LED+B
LED CONT
µ-CON+5V
GND

2

R739
47K

2.5V

2.5V

2.5V

2.5V

2.5V

2.5V

2.5V

2.5V

2.5V

2.5V

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

8

9

6

5

7

SEG2

SEG3

SEG4

SEG5

SEG6

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

SEG13

SEG14

SEG15

SEG16

COM3

1

COM2

2

COM1

3

IC701

SYSTEM MICROCOMPUTER

R747

470

IX0015SJ

CAM SW

23

VREF+

24

DI

25

CE

0V

P-MUTE0VP-CONT0VCD+B

R750

RESET

R751

5V

CLOCK

R752

5V

5V

R753

R754

R755

R756

R749

P-STB

4.6V

POWER5VSYS STOP5VREMOCON5VCLE

0.8V

JOG UP5VJOG DOWN5VID5VDATA0VCD RES0VCEE0VBUCK0VR-MUTE5VL-CONT

R759

R760

R757

+B

R761

75
74
73

53
52
51

2.5V

SEG17

2.5V

SEG18

SEG25
SEG26
SEG27

REC
0V
MOT
0V
SOL
0V

R764

2.5V

SEG19

1K

2.5V

2.5V

SEG20

SEG21

STEREO

SURROUND

2.5V

SEG22

SEG28
SEG29
SEG30
SEG31
SEG32
SEG33

BUS3
BUS2
BUS1
BUS0

CD STB

PU-IN

LID-SW

B-CAN

1.0V

2.8V

BIAS

2.5V

SEG23

SD

0V
0V
0V
0V
0V
5V
5V
0V
0V

0V

R796
1K

2.5V

767778798081828384858687888990919293949596979899

SEG24

0V

2.5V

75
74
73
72
71
70
69
68
67

R785 1K

66

R784 1K

65
64
63

R781 1K

62

R780 1K

61

R779 1K

60

R778 1K

59

R777 10K

58

R776 1K

57

R775 1K

56

R774 1K

55

R773 1K

54

R772 1K

53

R771 1K

52

R770 1K

51

R767 1K
R766 1K
R765 1K

2.5V

CF

2

1

R787 47K

R788 47K

DISPLAY PWB-A4

E

F

G

H

R855

100K

R854

100K

R853

100K

R852

100K

R815

231

BI681

231

CNS681

TO POWER PWB

CNP681

P21 10-G

2

5

5.

C857

47/16

C858

0.01

IC804

R823

1K

2.0V

SBAD

13

0V

FEO

14

2.1V

FEN

15

2.1V

VRO

16

10

2.9V

RFRP

17

2.1V

RFIS

18

9

2.1V

RFGO

19

2.1V

RFGC

20

2.1V

AGCI

21

1.7V

RFO

22

0V

8

GND

23

2.1V

RFN

24

S

+B

IC804

LA6541D

FOCUS/

DRIVER

C845

100/10

C848

R828

39P

1.2K

R826

R829

68K

C849

0.056

C846

0.1

R827
27K

2.7K

+B

C855

100/10

C844

0.0068

R825
100K

C847

0.1

C839

2P

+B

R813

10

+B

R817

R818

1K

1K

C833

C834

R816

470P

470P

10K

10K

+B

C831

R819
220

10/16

C836

0.056

C840

100/10

100/10

+B

C830

C832
10/16

C835

0.056

C837
470P

C828
100/10

C862

0.001

C825

0.056

0V

81

2.4V

82

0V

83

2.3V

84

2.4V

85

0V

86

5V

87

5V

88

5V

89

4.3V

90

4.3V

91

4.3V

92

4.3V

93

5V

94

0V

95

4V

96

3.3V

97
98

5V
5V

99

4.9V

100

1K

R820

2.6V

0V

XO

XVDD

17

DVR

LO

16

DVSL
TEST1
TEST2
TEST3
BUS0
BUS1
BUS2
BUS3
VDD
VSS
BUCK
/CCE

TEST0

/HSO

1234

0V

5.0V

C824

0.056

X801

16.93MHz

0V0V0V

0V5V5V0V2.2V

XI

PXI

VSS

VDD

PXO

XVSS

TESIO1

DVSR

81

RO

82

DVDD

83

SERVO/SIGNAL CONTROL

TEST4

98

/TSMOD

99
100

/RST

TESIN

/DACT

C823

0.01

C822
220/10

IO3

IO2

/CKSE

/DMOUT

IC802

TC9462F

5V0V0V0V0V5V0V

IO1

IO0

13

/UHSO

5.0V

DOUT

AOUT

EMPH

LRCK

VSS

BCK

MBOV

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

8

9

6

5

7

0V

0V

0V

0V

2.5V

2.5V

2.5V

DATA

VSS

SBOK

5.0V

CLCK

1.2V

SFSY

VDD

0V

0V

5.0V

2.4V

C820

0.01

IPF

0V

0V

VSS

SBSY

0V

VDD

55

56

SPCK

0V

C829

100/10

0V

FLGD

DMO

2VREF

SPDA

0.6V

0V5V5V

FLGC

COFS

1.7V

4

FLGB

50
49
48
51
52
53
54

33
32
31

MONIT

5.0V

0V

2.5V

FLGA

VREF
TRO
FOO
RFGC
TEBC
FMO
FVO

PVREF
LPFO
LPFN

VDD

0V

SEL

14

P2VREF

TESIO0

4.3V

15

6

7

5

HSSW

5.0V

C838

11

VCOREF

ZDET

47/10

R814 3.3K
R812 3.3K

C818 0.1

R811

2.2K

2.1V

2.1V0V2.2V0V4.3V

1

TEZI

TEI

TSIN

SBAD

FEI

RFRP

RFZI

RFCT

AVDD

RFI

SLCO
AVSS
VCOF

PDO

TMAXS

2.1V

2.1V

R801

+B

TRACKING/
SPIN/SLIDE

+B

0.1

0.1

C819

C821

0.1

C817

R810

1.8V

3.3K

515253545556575859606162636465666768697071727374757677787980

0V

R809

50

10K

2.2V

49

2.2V

48

2.2V

R808

47

3.3K

2.2V

46

2.1V

45

0V

44

2.0V

43

2.8V

42

2.1V

41

2.1V

40

5.0V

39

2.1V

38

2.1V

C806 0.0047

37

C805 0.0027

0V

36

1.4V

35

2.1V

C804 0.01

34

2.1V

33

C803 47/10

2.1V

32

2.1V

31

TMAX

R806

15K

12

2.1V

R804
100K

R802

10K

47K

C807

0.033

C801
100P

C802

0.015

R807
10K

C810

0.001

C809

0.001

C811
47/10

C813

47/10

0.01

C812

C863
220P

C850

220/10

+B

• NOTES ON SCHEMATIC DIAGRAM can be found on page 15.

1

23456

Figure 22 SCHEMATIC DIAGRAM (3/4)

– 22 –

XL-530H,CP-XL530H

7

8 9 10 11 12

1K
1K

1K
1K
1K
1K
10K
1K
1K
1K
1K
1K
1K
1K

7 1K

6 1K

5 1K

804
541D

CUS/

KING/

/SLIDE

IVER

845
0/10

C846

0.1

828

1.2K

R826

R827

R829

68K

849
056

SWITCH PWB-A6

CFW702

2

2

SW701
CD EJECT

1

1

+B

R787 47K

R788 47K

+B

C857

47/16

C858

0.01

C844

0.0068

R823

2.0V

SBAD

13

R825

0V

FEO

14

100K

2.1V

FEN

15

2.1V

VRO

16

2.9V

RFRP

17

2.1V

RFIS

18

2.1V

RFGO

19

2.1V

C847

RFGC

20

0.1

2.1V

AGCI

21

1.7V

C855

C839

RFO

22

0V

GND

23

2.1V

RFN

24

2P

+B

2.7K

27K

100/10

R793 47K

R794 47K

+B

D718

1N4004

R862

2.2K

Q861

2SB562 C

6.2V

2.2K

5.65V

R861

2.8V

2.2V

2.2V

5.1V

5.6V

IN

11K

OUT

REG

REG

LEVEL

REGU-

SHIFT2

AMP2

LATOR

LEVEL

IC804

RESET

AMP3

SHIFT3

RES

CD

VG3 VG2

VIN3 VIN2

11K

16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

5V

5V

2.2V

2.2V

2.8V

3.1V

2.5V

0V0V0V

2.8V

101112131415

8

9

6

5

7

VO1

VO2

VO3

VO4

BTL

BTL

AMP1

+

–

BTL

BTL

AMP4

VCC

VO8

VO7

VO6

VO5

0V0V0V

2.5V

2.8V

3.1V

3

1K

10

R824

2.2V

27K

TEO

12

2.1V

TEN

11

4.3V

2VRO

10

2.1V

TEB

9

2.5V

SEL

8

3.0V

LDO

7

9

0V

MDI

6

2.1V

TN1

5

2.1V

TPI

4

2.1V

FPI

3

2.1V

8

FNI

2

15V

VCC

1

IC801

TA2109F

SERVO PRE AMP.

C841

+B

100/10

2.0V

+B

6.3V

4.9V32.2V42.2V

1

2

VG1

VCC

MUTE

LEVEL
SHIFT1

LEVEL

+

–

SHIFT4

VCC

VREF

VIN4 VIN1

11K 11K

VG4

0V

2.2V

2.2V

2.2V

2.2K

R863

2

C842

22

47/10

3.7V

R822

Q801
KTA1266 GR
SWITCHING

CD SERVO PWB-A5

D GND
VDO
CL
DO
CE
DI

CD STB
BUS3
BUS2
BUS1
BUS0

+B

µ-CON5V
PU IN
BIAS
B-CAN
REC
MOT
SOL
P.F
RUN PLS
CAM-SW
R-MUTE
BUCK
CCE
CD RES

SD
STEREO

CD+B
P-STB
A 12V
P MUTE

+B

+B5V

0.1

C860

C859

220/10

0.1

C843

R80E 82K
R80A 82K

R80B 82K
R80C 82K
R80F 82K

R80G 82K
VREF
+5V

+B

CNS603

L-CH

1

L-CH

2

A_GND

3

A_GND

4

R-CH

5

R-CH

6

ERASE

7

A_GND

+B

+B

+B

+B

C864
47/10

+B

R908
47K

Q906

KRA102 M

M 12V

DRIVER

TAPE MOTOR

270

R904

6

7

6

7

6

7

C861

0.001

4.9V

11.7V

Q905

11.7V

2SB562 C

+B

47K

R903

4321

5

4321

5

4321

5

FOOL PROOF

+B

SWITCHING

1

4.9V

2

R907
10K

11.8V

D902

1N4148

C903

100/25

R902

56K

11.9V

11.8V

Q902

0V

2SB562 C

SOLENOID

DRIVER

D901

1N4148

SW901

µ-CON5V

0.6V

3

R906

1.5K

KRC102 M

SWITCHING

R901

1.5K

C901

TAPE MECHANISM PWB-D

+B

+B

+B

+B

+B

P.F
SOL
CAM-SW

CD RES

PU IN

CD STB

BUCK

CCE

BUS3

BUS2

BUS1

BUS0

A GND

CD L-CH

CD R-CH

MOT

C887

0.001

+B

4321

8

6

5

7

CNP101
CNS101

RECORD/PLAYBACK

L-CH

8

7

HEAD

6

5

R-CH

4321

ERASE

HEAD

CD MOTOR PWB-C

BI803

CNP803

SP+
SP–
SL+
SL–
PU-IN
GND

CNS803

6

6

5

5

4

4

3

3

2

2

1

1

+

SP+

6

SP–

5

SL+

4

SL–

3

PU-IN

2

GND

1

M

–

+

M

–

M802
SPINDLE MOTOR

M801
SLED MOTOR

SW801
PICKUP IN

PICKUP UNIT

BI801

R821

CNS801

TR–

TR–

1

1

1

TR+

TR+

2

2

2

FO+
FO–
GND

PD

VR

LD

BI802

C

F
B
A
E
1/2V
+5V

3
4
5
6
7
8

CNS802

1
2
3
4
5
6
7

FO+

3

FO–

4

GND

5

PD

6

VR

7

LD

8

C

1

F

2

B

3

A

4

E

5

1/2V

6

+5V

7

3
4
5
6
7
8

22

1
2
3
4
5
6
7

1/2VCC

C
F
B
A

E
GND
MON
LD
VCC

TR+
FO+
FO–
TR–
ACTUATOR

LT0H41M1

+B

CAM SW

P.F

RUN PLS

SOL

R905

10K

Q903

KRC107 M

SWITCHING

2

3.2V

1

C902

3

3.3/50

0.7V

R909

1K

BI901

CNS901

CNP901

PH901

PHOTO

INTERRUPTER

TAPE MECHANISM
PWB-E

TAPE MECHANISM ASSEMBLY

PLAYBACK SIGNAL

RECORD SIGNAL
CD SIGNAL

M 12V

D GND

FM ST

R-MUTE

P MUTE

A GND

S+6.2V

M GND

D903

1N4148

D904

1N4148

Q904

1

3

KRC102 M

SWITCHING

0.001

VDO

CL
DO
CE

DI

BIAS

B-CAN

REC

SD

CD+B

P-STB

A 12V

L-CH

R-CH

2

1

4.4V

2

11.7V

0V

Q901

CFW901

TAPE MOTOR

8
9

CNP603

P20 1-F

10

TO MAIN PWB

11
12
13
14
15

1
2
3
4
5
6
7
8

CNP602

P21 7-H

9

TO MAIN PWB

10
11
12
13
14
15

CNS602

3

C904

0.022

C905

0.022

SW902
CAM

–

+

M

SOL901

SOLENOID

M901

• The numbers 1 to 17 are waveform numbers shown in page 27.

Figure 23 SCHEMATIC DIAGRAM (4/4)

– 23 –

XL-530H,CP-XL530H

A

B

FROM TAPE
MECHANISM
GND

C

TO MAIN
CHASSIS
GND

(238)

(229)

2 1

CNP653

C681

POWER PWB-B

C689

C696

ZD682

R682

C682

R683

C660

C686

ZD681

C685

D684

2

1
CNP681

E C B

R684

3

R685

B C E

D683

Q682

Q681

E C B

D682

R686

Q683

C688

R681

TO MAIN PWB

CNP652

1 2

BR

RD

1

BI652

C695

D685

C683

C684

D681

2

P26 1-A

CNS652

D653

R680

C653

C654

D652

D654

SUB POWER TRANSFORMER

C652

C651

D651

T681

RLY681

F651

T2.5A L 250V

T651

MAIN POWER

TRANSFORMER

T.F

When servicing, pay attention as the area
enclosed by this line ( ) is directly
connected with AC main voltage.

LF651

SO651

SO651
AC POWER
INPUT
SOCKET
AC230V, 50HZ

D

M901

TAPE MOTOR

CFW901

RD

WH

E

YL

BR

SW901

FOOL

PROOF

RD

7 6 5 4 3 2 1

CNP901

SW902

CAM

TAPE
MECHANISM
PWB-D

TAPE

TAPE MECHANISM
ASSEMBLY

MECHANISM
PWB-E

PH901

PHOTE
INTERRUPTER

SOL901
SOLENOID

F

PICKUP UNIT

CD MOTOR PWB-C

COLOR TABLE

BR

G

H

RD(R)

OR

YL

GR

BL
VL

GY

WH(W)

BK
PK

BROWN

RED
ORANGE
YELLOW

GREEN

BLUE

VIOLET

GRAY
WHITE
BLACK

PINK

71

81

M802
SPINDLE
MOTOR

SW801

PICK UP IN

M801
SLED
MOTOR

CNP803

F3895AF

6
5
4
3
2
1

1

23456

Figure 24 WIRING SIDE OF P.W.BOARD (1/3)

– 24 –

7

8 9 10 11 12

SWITCH

PWB-A6

2

CFW702

1

CNS681

LED
PWB-A3

SW701

CD EJECT

BK

3

WH

2

BK

1

R799

Q707

SW717

BASS/TREBLE

R714

CFW702

2

1

CFW701

1
2

R716

R717

BI681

1

3

13

CD SERVO
PWB-A5

CNS901

GY

7

GY

6

GY

5

GY

4

GY

3

GY

2

BK

1

5

7

10

9

8

6

R718

12

B
C
E

R715

D718

C902

R719

3
2
1

Q706

1 2 3

R798

C855

Q903

7

R827

C850

C843

R905

C839

7

R904

B1802

R702A

3
2
1

C905

R901

R903

BI901

C901

R829

C849

R720

24

1

R760

R761

Q906

3
2
1

R826

C847

IC801

52010

R80G

R80F

R80C

R702B

R764

R770

R775

R787

SW703

SW710

FAST FOWARD

SW711

REWIND

D903

3
2

Q904

1

B C E

Q901

B C E
Q902

C903

D902
D901

1

R828

C846

13

15

12

R80E

R80B

R80A

1

R765

R771

PLAY

SW704

STOP

D904

C848

R766

R772

C904

R825

Q801

B C E

R702C

R767

R773

R908

R907

Q905

R902

C863

C801

C803

R824

R796

R774

R776

R909

R801

D706D704 D705

R802

C805

R739

R777

R906

R806

C804

C845

C842

R821

C806

R743

R778

BI801

R742

R779

2324

R711

R788

C838

C813

R823

R822

D707

R741

R780

22

R804

C802

C812

C841

21 20

C707

R703B R703A

R781

R807

C829

30

31

C844

R703C

D708

R785

R784

1819

16

17

R712

JOG DIAL

AB

C836

C837

C820

25

35

C807

R808

C811

18

D709

LCD701

12

1314

15

R721

R710

SW700

C706

R853

R852

10

15

20

IC802

40

45

55

50

51

R810

R809

C817

C809

11

R713

C

R854

1

5

60

R811

C810

10

95

65

C821

C859

R733

C705

100

C819

C818

9

R855

70

90

8

C835

75

R812

Q861

75
76

R727

85

C822

C860

B
C
E

7

R814

51

60

65

70

IC701

80

85

90

100

2

5

4

6

3

R725

R724

R729

R723

R794

C862

C831

C828

C840

C830

81

R813

80

R820

C824

C823

123456789

R863

CFW701

2

50

55

45

40

35

15

10

95

5

1

1

SW702
VOLUME/
JOGDIAL

SW705

FUNCTION

SW706

BAND

SW707

MEMORY SET

R793

C864

C832

R819

C887

C825

X801

C858

R861

R862

IC804

1

XL-530H,CP-XL530H

1

DISPLAY PWB-A4

R754

Q701

1 2 3

C710

R751

R70B

R70A

R70E

R70C

D721

D720

R728
R730

R731
R732

R70H

R815

6

L701

R745

R736

C834

C701

R746

R737

R817

C702

C861

X701

R747

X702

R749

D723

R70K

CNP101

R818

R70J

8
7
6
5
4
3
2
1

C711

B
C
E

R70M

CNS603

CNS602

26

30

25

20

R726

R744

R709

R738

R708

R816

C833

C857

1011 1213 1415

BI803

R707

C703

R750

R735

ZD701

161718192021222324252627282930

R753

Q705

1
2
3

ON/STAND-BY

R752

RECORD

CANCEL

C715

D722

Q703

Q702

B
C
E

R70F

R70L

C704

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

R755

R734

SW718

C712

SW708

PAUSE/

BEAT

R70G

RX701

CNS101

16

17

14

R757

R756

R759

R722
R769

SW719
CLOCK/
TIMER/
SLEEP

C713

1 2 3

RECORD/

C714

PLAYBACK
HEAD

RD

8

WH

7

BK

6

BK

5

WH

4

RD

3

WH

2

BK

1

TO MAIN PWB

CNP603

P26 4-H

4

TO MAIN PWB

CNP602

P26 4-H

RD

WH

RD WH

ERASE
HEAD

WH BK

1

CNS802

GYWHGYWHGYWHRD

7 6 5 4 3 2 1

WHGYWHGYWHGYWH

8 7 6 5 4 3 2 1

• The numbers 1 to 17 are waveform numbers shown in page 27.

Figure 25 WIRING SIDE OF P.W.BOARD (2/3)

– 25 –

RD

CNS801

11

2

3

RDWHGYWHGY

1 2 3 4 5 6

WH

15

CNS803

XL-530H,CP-XL530H

A

B

C

D

E

F

G

FROM POWER PWB

CNS652

P24 2-A

C614

C613

1 2 3 4 5 6 7 8 9 10

IC601

1

5

C402

R424

R420

R416

R418

24

C432

C433

R415

R417

R419

C401

R423

CNW601

51

R661

CNW601

C404

R426

C416

20

IC401

510

1

C415

C403

R425

C406

R436

13

15

R435

C405

R662

2 1

CNP652

R428

C418

12

C417

R427

C430

C419

R438

C422

C424

C431C421

R437

HEADPHONES PWB-A2

SO601

SPEAKER TERMINALS

GNDR-CH L-CHGND

C607

C699

C604

C603

C606

C697

Q602

E
C

R607

B

R603

R604

C615

C616

F653

T800mA L 250V

C426

R440

Q401

R443

R439

R448

R451

R449

R452

B

R450

C
E

C434

R441

R447

R444

R446

C425

R445

C428

ZD401

C420

R442

C423

J601

HEADPHONES

R615

R156

C608

C605

E
C
B

Q601

R453

D601

R601

R157

R616

R602

R624

R155

C601

R154

R153

Q606

Q152

E
C
B

E
C
B

C155

Q608

D604

3
2
1

Q609

C156

C154

C627

R629
R628

1
2
3

Q607
Q605

Q604

3
2
1

B
C
E

B
C
E

B
C
E

Q153

R617

R160

R620

C620

B
C
E

ZD602

R625

R623

D602

C622

ZD601

Q155

C626

C628

C625

D603

R159

B
C
E

Q154

P25 12-G

R627

R619

R621

Q603E C B

C331
R323
C334
C336

C335

C310

C388

C624

C367

R357

R356

C623

C374

C372

C371

R364

R634

Q151

R152

R362

E
C
B

R361

R363

R608

C151

C153

C621

C152

L151

TO CD SERVO PWB

T302

C330

VD301-1

R320

R350

C369

C368

TP302

15
14
13
12
11
10

9
8
7
6

CNP602

5
4
3
2
1

15
14
13
12
11
10

9

CNP603

8
7
6

C122

5
4
3

C121

2
1

R151

CNS603CNS602

P25 12-F

D302

C364

C349

D301

C337

C362

BF301

C319

C305

C307

C332

R324

VD301-2

C333

T306

C366

C373

3 2 1

Q351

Q172

1
2
3

C343
R358

3
2
1

FM

AM

FM/AM

LOOP

ANTENNA

123

CNP301

D306

C304

IC301

C318

123456789

R301

L302

C306

D305
VD303

R302

C303

R307

R303

R336

24
23
22
21
20
19
18
17
16
15
14

X351

Q171

C102

D106

C350

C363

3
2
1

R351

C354

C353

E C B

C101

R310

C308

TP301

R321

1

CF302

1
2
3

C361

R352

4
5
6
7

C360

8

9
10
11

C399

IC303

1213

C358

R393

C129

C130

Q103

B

Q102

C
E

R138

R139

L353

C352

R353

R355

C116

E C B
E C B

Q101

C114

9
8
7
6
5
4
3
2
1

R319

C365

Q104

C323

C309

C351

C398

CF351

C356

C357

R376

R118

R123

IC101

R101

C311

C317

C316

R306

T304

VD302

C313

C312

33221
CF352

C113

R102

R308

1 2 3

FM MUTE

LEVEL

T351

C355

C370

R117

C115

R116

C106
C104

R140
C103

C105

VR351

R385

R120

R124

R121
R122
R126

R381

B C E

C391

L352

R119
R125

C108

11

9
7
5
3
1

1 2 3

R136

R380

R382

Q360

R104

C107

C314

C393

R377

C117

12
10

8
6
4
2

R115

CF303

C385

C386

R383

D104

MAIN PWB-A1

R305

L303

R309

C397

R379

C380

L351

R395

R111

R134

R108

C123

IC102

Q107

D105

R311

C394

R360

C384

Q105

C126

R133

C125

R386

22
21
20
19
18
17
16
15
14
13
12

C112

C381

R359

C396

R131

C124
R135

C111
R103
R107

R312

R365

R387

R141

C118

R313

R384

Q305

R315

B
C
E

X352

C382

1
2
3
4

C392

5
6
7
8
9

C387

10
11

R374

ZD351

C395

R113

E C B

E C B
R110

C110

R106

R130

C

R314

Q306

C383

R392
R391

R114

R132

R128

C120

C109

B

E

R373
R372

R112

D102
D101

C119
R129
R127
R109

R105
R137

R304

C315

IC302

R371

Q106

H

1

23456

Figure 26 WIRING SIDE OF P.W.BOARD (3/3)

– 26 –

XL-530H,CP-XL530H

SAFETY PRECAUTION FOR SERVICE MANUAL

Precaution to be taken when replacing and servicing the Laser Pickup.

The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class I Requirements.
However, the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam
(1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than

the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens.
(2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping.
(3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup.
(4) Under no circumstances look directly into the Pickup Lens at any time.
(5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in

hazardous radiation exposure.

(For U.K.)

(FOR Europe)

LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT

Laser Diode Properties

Material: GaAIAs
Wavelength: 780 nm

Emission Duration: continuous
Laser Output: max. 0.6 mW

VAROITUS! LAITTEEN KÄYTTÄMINEN
MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA
TAVALLA SAATTAA ALTISTAA
KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.

VARNING - OM APPARATEN ANVÄNDS PÅ
ANNAT SÄTT ÄN I DENNA
BRUKSANVISNING SPECIFICERAS. KAN
ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING, SOM ÖVERSKRIDER
GRÄNSEN FÖR LASERKLASS 1.

CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO
BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.

VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA
EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT.

ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I
STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER.

VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE.
ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI.

VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD.
STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT
INSTRUMENT.

ADVERSEL-USYNLIG LASERSTRALING NAR DEKSEL APNES. STIRR IKKE
INN I STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.

IMPORTANT SERVICE NOTES (FOR U.K. ONLY)

Before returning the unit to the customer after completion of a
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.

Set name set value
Withstanding Voltage Tester
Test voltage 4,240 VPEAK

3,000 VRMS
Set time 6 secs
Set current(Cutoff current) 4 mA
Unit
Judgment
OK: The “GOOD” lamp lights.

NG: The “NG” lamp lights and the buzzor sounds.

– 2 –

WITHSTANDING

VOLTAGE TESTER

AC

OUT

SHORT-CIRCUT
AC POWER
SUPPLY CORD

PROBE

UNIT

CONNECT THE PROBE
TO GND OF CHASSIS
SCREW TERMINAL

FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.

SPECIFICATIONS

XL-530H (For Europe)

■ Main unit

● General

Power source: AC 230 V, 50 Hz
Power
consumption:
Dimensions: Width; 160 mm (6-5/16")

Weight: 2.6 kg (5.7 lbs.)

Stand-by; 0.6 W
Power on; 24 W

Height; 241 mm (9-1/2")
Depth; 249 mm (9-13/16")

XL-530H,CP-XL530H

XL-530H (For U.K.)

■ Main unit

● General

Power source: AC 230 V, 50 Hz
Power
consumption:
Dimensions: Width; 160 mm (6-5/16")

Weight: 2.6 kg (5.7 lbs.)

Stand-by; 0.6 W
Power on; 24 W

Height; 241 mm (9-1/2")
Depth; 249 mm (9-13/16")

● Amplifier section

Output power: PMPO; 28 W (Total)

MPO; 14 W (7 W + 7 W)
(DIN 45 324)
RMS; 10 W (5 W + 5 W)
(DIN 45 324)

Output terminals: Speakers; 4 ohms

Headphones; 16-50 ohms
(recommended; 32 ohms)

● Tuner section

Frequency range: FM; 87.5-108 MHz

AM; 522-1,620 kHz

● Compact disc player section

Type: Compact disc player
Signal readout: Non-contact, 3-beam semi-

conductor laser pickup

D/A converter: 1-bit D/A converter
Filter: 8-times oversampling digital

filter

Frequency
response: 20 - 20,000 Hz
Wow and flutter: Unmeasurable

(less than 0.001% W. peak)

● Cassette deck section

Frequency
response:
Signal/noise ratio: 50 dB
Wow and flutter: 0.3 % (DIN 45 511)

50 - 14,000 Hz (Normal
tape)

● Amplifier section

Output power: RMS; 10 W (5 W + 5 W)

(10 % T.H.D.)

Output terminals: Speakers; 4 ohms

Headphones; 16-50 ohms
(recommended; 32 ohms)

● Tuner section

Frequency range: FM; 87.5-108 MHz

AM; 522-1,620 kHz

● Compact disc player section

Type: Compact disc player
Signal readout: Non-contact, 3-beam semi-

conductor laser pickup

D/A converter: 1-bit D/A converter
Filter: 8-times oversampling digital

filter

Frequency
response: 20 - 20,000 Hz
Wow and flutter: Unmeasurable

(less than 0.001% W. peak)

● Cassette deck section

Frequency
response:
Signal/noise ratio: 50 dB
Wow and flutter: 0.25 % (WRMS)

CP-XL530H (For U.K.)

50 - 14,000 Hz (Normal
tape)

CP-XL530H (For Europe)

■ Speaker

Type: Full range speaker system
Speakers: 10 cm (4") full-range

speaker

Rated input power: 5 W

Maximum input
power:

Impedance: 4 ohms
Dimensions: Width; 145 mm (5-3/4")

Weight: 1.4 kg (3.1 lbs.)/each

10 W

Height; 240 mm (9-1/2")
Depth; 191 mm (7-1/2")

■ Speaker

Type: Full range speaker system
Speakers: 10 cm (4") full-range

speaker

Rated input power: 5 W

Maximum input
power:

Impedance: 4 ohms
Dimensions: Width; 145 mm (5-3/4")

Weight: 1.4 kg (3.1 lbs.)/each

Specifications for this model are subject to change without
prior notice.

– 3 –

10 W

Height; 240 mm (9-1/2")
Depth; 191 mm (7-1/2")

XL-530H,CP-XL530H

XL-530H

NAMES OF PARTS

■ Front panel

11. Timer Indicator

12. Record Indicator

13. Sleep Indicator

14. (CD) Repeat Indicator

15. (CD) Play Indicator

16. (CD) Random Indicator

17. (CD/TUNER) Memory Indicator

18. FM Stereo Mode Indicator

19. FM Stereo Indicator

10. CD Compartment

11. On/Stand-by Button

12. Volume/Jog Dial Selector Button

13. Record Pause/Beat Cancel Selector
Button

14. Clock/Timer/Sleep Button

15. Function Selector Button

16. Remote Control Sensor

17. Band Selector Button

18. Memory/Set Button

19. Headphone Socket

20. CD Eject Button

21. Bass/Treble Selector Button

22. (CD) Play/Pause Button

3 (TAPE) Play Button

23. (CD/TAPE) Stop Button
(TUNER) Clear Button

24. (CD) Cue Button
(TAPE) Fast Forward Button
(TUNER) Tuning Up Button

25. (CD) Review Button
(TAPE) Rewind Button
(TUNER) Tuning Down Button

26. Jog Dial

27. Cassette Compartment

10

11

12
13
14

15
16

17
18

19

4

5

6

27

1

23

7

89

20

21

22

23
24
25

26

■ Rear panel

11. AC Power Input Socket

12. FM/AM Loop Aerial Socket

13. Speaker Terminals

2

3

1

– 4 –

CP-XL530H

■ Speaker section

11. Bass Reflex Duct

12. Full-Range Speaker

13. Speaker Wire

XL-530H

XL-530H,CP-XL530H

1
2

3

■ Remote control

1. Remote Control Transmitter LED

●Tuner control section

2. Preset Up/Down Buttons

●CD control section

3. Clear Button

4. Random/Repeat Button

5. Memory Button

6. Stop Button

7. Play/Pause Button

8. Track Down/Review Button

9. Track Up/Cue Button

● Tape control section

10. Record Pause/Beat Cancel Selector
Button

11. Rewind Button

12. Stop Button

13. Play Button

14. Fast Forward Button

● Common section

3
4

5

10

11

15

16
17

18

1

2

6

7
8

9

12
13

14
19

20

21

22

15. Sleep Button

16. Bass Up/Down Buttons

17. Function Selector Buttons

18. On/Stand-by Button

19. Timer Button

20. Clock Button

21. Treble Up/Down Buttons

22. Volume Up/Down Buttons

– 5 –

XL-530H,CP-XL530H

PREPARATION FOR USE

■

Remote control

Notes concerning use:

● Replace the batteries if the operating distance is

reduced or if the operation becomes erratic.

● Periodically clean the transmitter LED on the re-

mote control and the sensor on the main unit with

a soft cloth.

● Exposing the sensor on the main unit to strong

light may interfere with operation. Change the

lighting or the direction of the unit.

● Keep the remote control away from moisture, ex-

cessive heat, shock, and vibrations.

15

15

0.2 m - 6 m

(8" - 20")

RESETTING THE MICRO-

COMPUTER

Reset the microcomputer under the following

conditions:

● To erase all of the stored memory contents (clock

and timer settings, and tuner and CD presets).

● If the display is not correct.

● If the operation is not correct.

1

Press the ON/STAND-BY button to enter the

stand-by mode.

2

Unplug the AC power lead from the AC INPUT

socket on this unit.

3

Whilst pressing down the MEMORY/SET button

and the BASS/TREBLE button, plug the AC

power lead into the AC INPUT socket on this unit.

Caution:

● The operation explained above will erase all data

stored in memory, such as clock and timer set-

tings, and tuner and CD presets.

1

3

3

2,3

SETTING THE CLOCK

In this example, the clock is set for the 24-hour

(0:00) system.

1

Press the CLOCK/TIMER/SLEEP button to enter

the time check mode.

2

Within 3 seconds, press the MEMORY/SET but-

ton.3Turn the jog dial to select the time display mode.

"0:00" → The 24-hour display will appear.

(0:00 - 23:59)

"AM 12:00" → The 12-hour display will appear.

(AM 12:00 - PM 11:59)

● Note that this can only be set when the unit is first

installed or it has been reset.

4

Press the MEMORY/SET button.

5

Adjust the hour by turning the jog dial.

● When the jog dial is turned one click clockwise,

the time will increase by 1 hour. When it is turned

one click anti-clockwise, the time will decrease by

1 hour.

Keep turning the jog dial to change the time con-

tinuously.

● When the 12-hour display is selected, "AM" will

change automatically to "PM".

6

Press the MEMORY/SET button.

7

Adjust the minutes by turning the jog dial.

● When the jog dial is turned one click clockwise,

the time will increase by 1 minute. When it is

turned one click anti-clockwise, the time will de-

crease by 1 minute.

Keep turning the jog dial to change the time con-

tinuously.

● The hour setting will not advance even if minutes

advance from "59" to "00".

8

Press the MEMORY/SET button.

● The clock starts operating from "0" seconds. (Sec-

onds are not displayed.)

Note:

● In the event of a power failure or when the AC

power lead is disconnected, the clock display will

go out.

When the AC power supply is restored, the clock

display will flash on and off to indicate the time

when the power failure occurred or when the AC

power lead was disconnected.

If this happens, follow the procedure below to

change the clock time.

To change the clock time:

Perform steps 1, 2 and 5 - 8 above.

To change the time display mode:

1

Perform steps 1 - 3 in the section "RESETTING

THE MICROCOMPUTER".

2

Perform steps 1 - 8 above.

CLOCK/TIMER/

SLEEP

MEMORY/

SET

Jog dial

(Main unit operation)

0:00 AM 12:00

2

3

4

5

6

7

8

OPERATION MANUAL

– 6 –

DISASSEMBLY

CD Mechanism

(J1)x3
ø2.5x10mm

PWB Washer x3

Top Cabinet

Caution on Disassembly

Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:

1. Take cassette tape and compact disc out of the unit.

2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit.

3. Take off nylon bands or wire holders where they need to
be removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were
before disassembling.

4. Take sufficient care on static electricity of integrated
circuits and other circuits when servicing.

XL-530H

STEP REMOVAL

1 Side Panel 1. Screw .................. (A1) x8 7-1

(Left/Right)

2 Top Cabinet/ 1. Screw .................. (B1) x1 7-1

Switch PWB 2. Socket ................. (B2) x3

(Note) 3. Hook .................... (B3) x2

3 Rear Panel 1. Screw .................. (C1) x1 7-1

4 Main PWB/ 1. Screw .................. (D1) x1 7-2

Headphones PWB 2. Screw .................. (D2) x2

5 Display PWB/ 1. Screw .................. (E1) x4 7-2

CD Servo PWB/ 2. Socket ................. (E2) x3

LED PWB 3. Knob .................... (E3) x1

(With Switch PWB) 4. Hook .................... (E4) x6

6 Front Panel 1. Screw .................. (F1) x1 7-2

7 Power PWB 1. Screw .................. (G1) x4 7-2

8 Tape Mechanism 1. Open the cassette holder 7-3

9 CD Mechanism 1. Screw .................. (J1) x3 7-4

PROCEDURE

3. Socket ................. (D3) x3

2. Screw .................. (G2) x1

3. Screw .................. (G3) x2

4. Bracket ................ (G4) x1

2. Screw .................. (H1) x4

FIGURE

XL-530H

LED PWB

(E3)x1

Display PWB

Tape
Mechanism
PWB

(E2)x1

Headphones
PWB

(E2)x1

(G3)x1
ø3x6mm

Power PWB

(G3)x1
ø3x6mm

Power PWB

Sub Power
Transformer

(E4)x6

(D4)x1

Front Panel

Open

Front Panel

(F1)x1
ø3x8mm

(G4)x1

Figure 7-2

XL-530H,CP-XL530H

(E1)x4
ø2.5x10mm

Main PWB

(D2)x1
ø3x8mm

(G2)x1
ø3x10mm

Main Power Transformer

Sub Power Transformer

Tape
Mechanism

(D3)x2

CD Servo PWB

(D2)x1
ø3x8mm

(E2)x1

(D1)x1
ø3x10mm

(G1)x4
ø3x6mm

Top
Cabinet

(A1)x1
ø3x10mm

Front
Panel

Side Panel
(Right)

(B3)x2

Swicth
PWB

(A1)x2
ø3x10mm

Top Cabinet

Figure 7-1

(A1)x1
ø3x10mm

(B2)x2

RearPanel

CD Motor PWB

CD Mechanism

(B1)x1
ø3x10mm

(A1)x4
ø3x10mm

Side Panel
(Lift)

(C1)x1
ø3x10mm

– 7 –

Cassette
Holder

(H1)x4
ø2.5x10mm

Figure 7-3

(B2)x1

Figure 7-4

Note:

After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of connector to protect the optical pickup from
electrostatic damage.

XL-530H,CP-XL530H

CP-XL530H

STEP REMOVAL PROCEDURE FIGURE

1 Speaker 1. Net........................... (A1) x1 8-1

2. Screw ...................... (A2) x4

CP-XL530H

(A1)x1

Speaker Box

Woofer

(A2)x4
ø4x12mm

Driver

Direction of handle

Figure 8-1

Driver should be
pried away from
speaker Box.

REMOVING AND REINSTALLING THE MAIN PARTS

CD MECHANISM SECTION

Perform steps 1 to 5 and 9 of the disassembly method to
remove the CD mechanism.

How to remove the pickup (See Fig. 8-2)

1. Remove the mechanism cover, paying attention to the
pawls (A1) x 4 pcs.

2. Remove the screws (A2) x 2 pcs., to remove the shaft (A3)
x 1 pc.

3. Remove the stop washer (A4) x 1 pc., to remove the gear
(A5) x 1 pc.

4. Remove the pickup.

Note:

After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of connector to protect the optical pickup from
electrostatic damage.

Mechanism Cover

(A1) x2

(A1) x2

(A2) x2
ø2.6 x6mm

CD Mechanism

Shaft
(A3) x1

StopWasher
(A4) x1

– 8 –

Gear
(A5) x1

Pickup Unit

Figure 8-2

MECHANISM SECTION

• Driving Force Check

Torque Meter

Play: TW-2412 Over 80 g

Specified Value

XL-530H,CP-XL530H

ADJUSTMENT

TAPE MECHANISM

• Torque Check

Torque Meter

Play: TW-2111 30 to 60 g. cm
Fast forward: TW-2231 55 to 140 g.cm
Rewind: TW-2231 55 to 140 g.cm

Specified Value

• Tape Speed

Test Tape

Adjusting

Point

MTT-111 Motor 3,000 ± Headphone

(M901) 90 Hz terminal

Specified

Value

Instrument

Connection

TUNER SECTION

fL: Low-range frequency
fH: High-renge frequency

• FM RF

Signal generator: 1 kHz, 75 kHz dev., FM modulated

Test Stage Frequency

Frequency

Display

FM Band — 87.50 MHz (fL): L303 *1
Coverage 3.4 ± 0.1 V

FM RF 98.00 MHz 98.00 MHz L302 *2

(10~30 dB)

*1. Input: Antenna, Output: TP301
*2. Input: Antenna, Output: Speaker Terminal

• AM IF/RF

Signal generator: 400 Hz, 30%, AM modulated

Test Stage Frequency

AM IF 450 kHz 1,620 kHz T351 *1

AM Band — 522 kHz (fL): T306 *2

Coverage 1.1 ± 0.1 V
AM Tracking 990 kHz 990 kHz (fL): T302 *1

Frequency

Display

*1. Input: Antenna, Output: Speaker Terminal
*2. Input: Input is not connected, Output: TP301

• FM Detection

Signal generator: 10.7 MHz, FM sweep generator

Test

Frequency

Stage

FM IF 10.7 MHz 98.00 MHz T304(Turn Input: Pin 1 of

Frequency

Display

• FM Mute Level

Signal generator: 1 kHz, 40 kHz dev., FM modulated

Frequency

Display

98.00 MHz 98.00 MHz VR351*1 Input: CNP301
(25 dBµV) Output: Speaker

Adjusting

*1. Adjust so that an output signal appears.

Setting/

Adjusting

Instrument

Connection

Parts

Setting/

Adjusting

Instrument

Connection

Parts

Setting/

Adjusting

Instrument

Connection

Parts

the core of IC301
T304 fully Output: TP302
counter­clockwise.

Instrument

Parts

Connection

Terminal

M901
Tape
Motor

Volume in
motor

Figure 9-1 ADJUSTMENT POINT

MAIN PWB

IC302

AM IF

FM Mute

T351

Level

CF352

IC303

TP302

CNP602

VR351

T306

AM Band
Coverage fL

TP301

Figure 9-2 ADJUSTMENT POINTS

• Setting the Test Mode

Keeping the FF/FWD button and MEMORY button pressed,
turn on POWER. Then, the frequency is initially set in the
memory as shown in Table. Call it with the Jog volume button
by pressing the VOLUME/JOG button to use it for adjustment
and check of tuner circuit.

Preset No. FM STEREO

1 87.50 MHz 6 522 kHz
2 108.00 MHz 7 1,620 kHz
3 98.00 MHz 8 990 kHz
4 90.00 MHz 9 603 kHz
5 106.00 MHz 10 1,404 kHz

11~25

Preset No. FM MONO

26 106.00 MHz
27 90.00 MHz
28 98.00 MHz
29 108.00 MHz
30 87.50 MHz

R336

FM Band
Coverage fL

FM IF

FM RF

AM
Tracking fL

Preset No.

L303

T304

L302

T302

IC301

9

1

BF301

AM

CNP301

FM/AM
ANTENNA
SOCKET

– 9 –

XL-530H,CP-XL530H

TEST MODE

The test mode applied to this microcomputer has three modes, namely ordinary test mode to be used for adjustment or
measurement, aging test mode to be used for aging test, and self-diagnosis test mode for self-inspection in case of final product
inspection.
The test mode specification prescribes the microcomputer with RDS (RH-IX0014SJZZ) and the microcomputer without RDS (RH­IX0015SJZZ). There are two types of indication examples; large ones for the microcomputer with RDS, and smaller ones for the
microcomputer without RDS.

1. Turning on the test mode

To turn on the specific test mode, press the POWER button, holding down the following two buttons in the ordinary stand-by
mode (power off state). In this case only the main unit button is valid. Even when the POWER of remote control button is set
to on, the test mode is not turned on.

[Ordinary test mode]

1. CD Test Mode (TEST 1)………………………… BASS/TREBLE + PLAY

2. Tuner Test Mode (TEST 2)……………………… FF/FWD + MEMORY/SET

3. Electronic volume Test Mode (TEST 3)…………STOP + BASS/TREBLE

4. Timer Test Mode (TEST 4)……………………… FF/FWD + BAND

5. LCD Test Mode (TEST 5)…………………………MEMORY/SET + REW/REV

[Self-diagnosis Test Mode]

1. Button input diagnosis test mode (TEST6).………

FF/FWD + REC PAUSE

– 10 –

XL-530H,CP-XL530H

2. CD Test Mode (TEST 1)

In the CD test mode the operation of each step is enabled even when the LID-SW is off. However, if focus cannot be set in step
3 or any error processing is started, it is impossible to proceed to the next step. When the error processing is started, operations
other than termination of test mode by pressing the POWER button or return to the step 1 by pressing the STOP button are inhibited.

1. Step 1 Mode
When the CD test mode is turned on, the following indication lights, the processing (until turning-off of CD STB terminal of CD
initialization operation flow) is executed, and the next button input is waited.

After lighting for one second

If the following operation buttons are pressed in this state, the operation is performed as follows.

"POWER"................. The test mode is turned off, the power is turned off, and the ordinary standby mode is set.

"FF/FWD".................After the pickup returns once to the innermost periphery, it slides toward the outer periphery while this

button is held down.

"REW/REV"..............After the pickup returns once to the innermost periphery, it slides toward the inner periphery while this

button is pressed. However, if PU-IN is on, input is invalid.

"PLAY" ..................... Shift to step 2

"STOP".....................Invalid

"REC PAUSE"..........Shift to step 5

* In case of initialization the pickup is moved toward the inner periphery. Any buttons other than "POWER" button are not

accepted until the shift of pickup to the inner periphery is completed at this time. If PU-IN SW ON cannot be detected within
10 seconds, the slide motor is stopped, and the following error indication appears. Press the POWER button to end the test
mode, or press the STOP button to return to step 1. Any other operations are inhibited.

2. Step 2 Mode
When the "PLAY" button is pressed in this mode, the laser lighting command LDON (8400) is sent, and the laser is turned on.
Other operations are not performed.

If the following buttons are pressed in this state, the operation is performed as follows.

"POWER" ................The test mode is turned off, the power is turned off, and the ordinary standby mode is set.

"FF/FWD" ................The pickup slides toward the outer periphery while this button is held down.

"REW/REV" .............The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input

is invalid.

"PLAY".....................Shift to step 3

"STOP" ....................Return to step 1

"REC PAUSE" .........Shift to step 5

– 11 –

XL-530H,CP-XL530H

3. Step 3 Mode
The laser is kept lighting. The processing (until turning-on of CLV servo of CD initialization operation flow) is executed, and
the next button input is waited. (The focus servo is turned on, and focus search is performed.)
The focus search is repeated until the focus is set.

When the following operation buttons are pressed in this state, the operation is executed as follows.

"POWER" ................The test mode is turned off, the power is turned off, and the ordinary standby mode is set.

"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.

"REW/REV" .............The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input

is invalid.

"PLAY".....................If the focus has been set, shift to step 4 is executed. If the focus has not been set, acceptance is inhibited.

"STOP" ....................Return to step 1

"REC PAUSE" .........Shift to step 5

*If the focus is disturbed after it has been set, the process returns to step 1.

4. Step 4 Mode

The CLV servo ON command (8600) sending operation is performed, and the next button input is waited. (The disc is rotated
to perform CLV locking.)

The time display indicates always "0:00".

When the following buttons are pressed in this state, the operation is executed as follows.

"POWER" ................The test mode is turned off, the power is turned off, and the ordinary standby mode is set.

"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.

"REW/REV" .............The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input

is invalid.

"PLAY".....................Shift to step 5

"STOP" ....................Return to step 1

"REC PAUSE" .........Shift to step 5

*If the focus is disturbed, the process returns to step 1.

5. Step 5 Mode

The CD initialization operation flow is executed to the end, the mute is set to off, and playback is started. Even when the
playback reaches the outermost periphery of disc, the operation does not stop. The LCD display indicates the playback past
time as in case of ordinary CD playback.

When the following operation buttons are pressed in this sate, the operation is executed as follows.

"POWER"................. The test mode is turned off, the power is turned off, and the ordinary standby mode is set.

"FF/FWD".................The pickup slides toward the outer periphery while this button is held down.

"REW/REV"..............The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input

is invalid.

"PLAY" .....................Invalid

"STOP".....................Return to step 1

"FUNCTION"............Shift to step 6

"BAND" ....................Shift to step 7

*If the focus is disturbed, the process returns to step 1.
Other cautions

• TOC IL is not executed in the test mode.

• As for button operations other than those shown above, only the sound volume operation (with JOG) is accepted.

– 12 –

XL-530H,CP-XL530H

3. Tuner Test Mode (TEST 2)

1. Outline of tuner (radio) test mode
The tuner test mode is intended to store the adjustment and measurement frequencies in the preset memory CH without

frequency setting by adjusting personnel when the tuner section is adjusted in the production line.

2. Details of tuner test mode
When the power is turned on by using the "POWER" button while the "FF/FWD" and "MEMORY/SET" buttons are held down

in POWER OFF state, the frequency for adjustment and measurement of destination specified by the AREA terminal is preset
and stored in the preset memory CH. However, Ordinary 1 and Ordinary 2 are set to the designation (destination selected
by SPAN switching operation) set when the test mode is set. (As for frequencies to be preset and stored for each destination,

refer to item 3.)
The tuner test mode is started from preset No.1.
The operations of test mode are identical with the ordinary operations of TUNER function. However, FUNCTION switching

is invalid.
Since it is necessary to discard the content of preset memory when the tuner test mode is ended, "0000" or "1111" bits are

written in the memory to be checked in case of memory check (in case of initial setting) so that memory abnormality is detected

in case of initial setting so as to ensure memory initialization.

When the tuner test mode is turned on, the following indication lights for one second.

• The TUNER TEST2 mode is set as a result of >> + MEMORY + POWER. -> IF AC is set to OFF in the TEST2 mode, the initial
state is restored.

When POWER is set to OFF, the memory of TEST2 mode is protected.
When the power is turned on again, the ordinary operation is enabled while the data is stored in the
memory (besides TUNER).

If AC OFF state is maintained in this state for about 1/2 day, start is executed in the initial state.

• To clear the whole memory, insert the AC cord, holding down MEMORY + BASS/TREBLE.

3. Preset frequencies for various destinations (random preset memory)

Europe 2, 4CH

1 FM 87.50 MHz
2 FM108.00 MHz
3 FM STEREO FM 98.00 MHz
4 FM 90.00 MHz
5 FM106.00 MHz

6 AM 522 kHz
7 AM1620 kHz
8 AM AM 990 kHz
9 AM 603 kHz
10 AM1404 kHz

11
12
13 LW
14
15

BAND

16
17
18
19
20

21
22
23
24
25

26 FM106.00 MHz
27 FM 90.00 MHz
28 FM MONO FM 98.00 MHz
29 FM108.00 MHz
30 FM 87.50 MHz

Europe 2, 4CHBAND

• The hatched sections of the table are not stored in memory.

– 13 –

XL-530H,CP-XL530H

4. Electronic volume Test Mode (TEST 3)

When the test mode is set, the following indication lights for one second.

When this mode is set, BASS/TREBLE is set to 0 (0 dB) and SURROUND mode is set to off, and start-up function is set to CD
when volume is -14 dB (STEP 17). The button operations in the test mode are the same as those of ordinary operation excepting
sound volume UP/DOWN.

(1) The indication is the same as that of ordinary operation excepting test mode setting.
(2) The sound volume control with the sound volume UP/DOWN button is only the following 3 steps unlike the ordinary state.

Volume- ∞ (STEP 0) <-> Volume-14 dB (STEP 23) <-> Volume-0 (STEP 30)

(3) BASS/TREBLE and SURROUND are switched when button operation is performed.

5. Timer test Mode (TEST 4)

When the test mode is set, the following indication lights for one second.

The current time and timer time are set in the following procedure to perform the timer playback.

1.Set the current time to 1:00, set the timer to ON time 1:02, set the function to Tape, and set volume STEP 8. One minute is counted
as one second, and the timer playback operation is performed. The fade-in (when playback is started) is executed at a rate of
one step for 0.5 sec. After completion of fade-in the fade-out is executed at a rate of one step for 0.5 sec (WAIT 1 sec inserted).
After completion of fade-out the power is turned off (after WAIT 1 sec), and the mode is changed to the standby mode.

The indication during operation is the same as that of ordinary timer operation.

6. LCD Test Mode (TEST 5)

When the LCD test mode is set, all the LCD segments are lighted. After that the indication is changed as follows according to
the "PLAY" button input.

Lighting of all segments Lighting of odd segments Lighting of even segments

7. Key input diagnosis Test Mode (TEST 6)

When the test mode is set, the following indication appears.

This test mode is intended to check whether all the main unit buttons can be detected. Accordingly, in this test mode checking
as to whether the "POWER" button was pressed after all the buttons shown below were pressed is performed. If the result is
OK, OK is indicated. Even any one of keys was not pressed, an error is indicated. In case of OK termination or error termination
exit from this mode occurs when the "POWER" button is pressed next time, and the standby mode is set.
The button pressing order is not specified. Checking as to whether all the buttons were pressed is executed.

[Detection button]

The button 11 below will be detected as all buttons.
PLAY, JOG MODE, BAND, BASS/TREBLE, FUNCTION, MEMORY/SET, REC PAUSE, REW, FF, STOP, CLOCK/TIMER/
SLEEP

The OK/NG indication of test result is as follows.

– 14 –

NOTES ON SCHEMATIC DIAGRAM

XL-530H,CP-XL530H

• Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.

• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to
electrolytic capacitor, the expression “capacitance/withstand
voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type

• Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.

REF. NO DESCRIPTION POSITION POSITIONREF. NO DESCRIPTION

SW700 JOG DIAL ON—OFF
SW701 CD EJECT ON—OFF
SW702 VOLUME/JOG DIAL ON—OFF
SW703 PLAY ON—OFF
SW704 STOP ON—OFF
SW705 FUNCTION ON—OFF
SW706 BAND ON—OFF
SW707 MEMORY/SET ON—OFF
SW708 RECORD PAUSE ON—OFF

• The indicated voltage in each section is the one measured
by Digital Multimeter between such a section and the chas­sis with no signal given.

1. In the tuner section,

( ) indicates AM
< > indicates FM stereo

2. In the main section, a tape is being played back.

3. In the deck section, a tape is being played back.

( ) indicates the record state.

4. In the power section, a tape is being played back.

5. In the CD section, the CD is stopped.

• Parts marked with “ ” ( ) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.

SW710 FAST FORWARD ON—OFF
SW711 REWIND ON—OFF
SW717 BASS/TREBLE ON—OFF
SW718 ON/STAND-BY ON—OFF
SW719 CLOCK/TIMER/SLEEP ON—OFF
SW801 PICKUP IN ON—OFF
SW901 FOOL PROOF ON—OFF
SW902 CAM ON—OFF

FRONT VIEW

FRONT

VIEW

FRONT

VIEW

2SB562 C
2SC2001 K
2SC535 C
2SD468 C
KRA102 M
KRC102 M

FRONT

VIEW

FRONT
VIEW

KRC104 M

ECB

(S)(G)(D)
(1) (2) (3)

KRC107 M
KTA1266 GR
KTC3199 GR

BCE

2SD2012 Y

Figure 15 TYPES OF TRANSISTOR AND LED

L1154GDA

KV1236Z23

KDV147C

MEASURES TO BE TAKEN TO CHANGE THE MICROCOMPUTERS, STARTING
FROM SERIAL No. 905xxxxx

The system microcomputers and peripheral parts will be changed as follows, starting from 1999 Serial No. 905xxxxx.
When microcomputers from the 1999 Serial No. 904xxxxx are repaired, special attention should be paid so that they are changed
according to the following instructions.
(There is no problem in using the NEW microcomputers without changing the peripheral circuits.)

Serial No. (904xxxxx)

REF. NO DESCRIPTION PARTS CODE PARTS CODE

IC701 System Microcomputer RH-iX0015SJZZ RH-iX0022SJZZ
C707 4.7µF, 25V, Electrolytic RC-GZA475AF1E Abolition
R909 1 kohm, 1/6W VRD-ST2CD102J Jumper

Serial No. (905xxxxx~)

– 15 –

WAVEFORMS OF CD CIRCUIT

NO DISC FOCUS SEARCH STOP PLAY

XL-530H,CP-XL530H

1

FOO

IC802 48pin

FO+ 2

2

IC804 26pin

3

FO- 3 DMO 3

IC804 25pin

FOCUS SEARCH TOC IL STOP PLAY

4

SEL 1 TEI 1

IC802 57pin

5

FEI 2 TRO 2

IC802 43pin

TEI 3 FMO 3

6

IC802 46pin IC802 53pin

STOP PLAY CUE

5

IC802 43pin

IC802 44pin

FEI

SBAD 2 TRO 2

7

1 TMAX 1

1 TEI 1

12

IC802 30pin

13

IC802 12pin

14

IC802 55pin

6

IC802 46pin

11

IC802 49pin

15

6

IC802 46pin

11

IC802 49pin

SBOK

2

RFO 3 FMO 3

8

IC801 22pin

STOP PLAY REVIEW

5

FEI

IC802 43pin

RFGO 2 TRO 2

9

IC801 19pin IC802 49pin

RFRP 3

10

IC801 17pin

STOP PLAY TCD-782 TNO-02 PLAYBACK

TEI 1LO 1

6

IC802 46pin

TRO 2

11

IC802 49pin

SBAD 3

7

IC802 44pin

1 TEI 1

15

IC802 53pin

6

IC802 46pin

11
15

IC802 53pin

16

IC802 85pin

17

IC802 82pin

FMO

RO 2

3

– 27 –

XL-530H,CP-XL530H

TROUBLESHOOTING

When the CD does not function

When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate, clean
the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check
the following items.
Remove the cabinet and follow the troubleshooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup
lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."

Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.

Dust gradually accumulates on the objective lens during use, and it may degrade performance.
To avoid this problem, use a cleaning disc designed for CD optical pickup lenses.

HOW TO USE

1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has
the mark next to it.

2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button.

3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop

button.

CAUTION

The CD lens cleaner should be effective for 30~50 operations, however if the brushes become worn out earller then please

replace the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth.
Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and /

or rinse with clean water and seek medical advice.
The CD cleaner disc must not be used on car CD players or on computer CD ROM drives.
All rights reserved. Unauthorized duplicating, broadcasting and renting this product is prohibited by law.

Cleaner Liquid

Cleaning Disc
PARTS CODE: UDSKA0004AFZZ

– 28 –

Make sure that the disc is normal, and set the CD TEST MODE (STEP 1).

XL-530H,CP-XL530H

Is the measured voltage as specified in circuit diagram?

Yes

Is "PU ERROR" displayed"?

Yes

Move the pickup to most internal circumference side of
Turn the power off and reset the CD TEST MODE (STEP 1).
Is "PU ERROR " not displayed?

Yes

Is +5V applied to pin 100 (/RST) of IC802?

Yes

Does the CD TEST MODE advance from "STEP 2"?

Yes

Does the laser come on in CD TEST MODE "STEP 2"?

Yes

Does the CD TEST MODE advance from "STEP 3" to "STEP
4"?

Yes

Does the spindle motor rotate normally when the CD TEST
MODE changes from "STEP 4" to "STEP 3"?

Yes

No

No

No

No

No

No

No

Check the main unit power supply circuit.

Check the pattern between pin 57 (PUIN) of IC701 and BI803/

No

CNS803.
Check the between BI803/CNS803 and PU-IN switch.

Check the PWB pattern between pin 45 (CD RES) of IC701 and
pin 100 (/RST) of IC802.

Is CD Lid switch SW701
ON condition ?

Yes

Check the between pattern IC701 and SW701 If OK.
Check the main unit power supply circuit.

Check the procedure in "LASER FAILURE".

Check the procedure in "FOCUS FAILURE".

Check the procedure in "SPINDLE MOTOR CLV SERVO
FAILURE".

Set ON condition the CD

No

Lid switch.

Is the HF output on pin 38 of IC802 in CD TEST MODE "STEP 5"?

Yes

Does the sound heard when the optical pickup move to the
selected play by the FF/REW key.

Yes

Does the LCD track number and time indicator work properly ?

Yes

Turn the power off and then back on.
Does the unit initialize properly and start playback when PLAY
key is pressed?

Yes

Does the unit play in order in the FF mode?

Yes

Does playback continue for 30 seconds after the start of
playback ?

Yes

Normal

No

No

No

No

No

No

– 29 –

Check the procedure "HF ERROR".

Does the sled motor
move ?

Yes

Check the procedure "NO SOUND"

Check the pattern between IC701 and LCD701.

Is "PU ERROR
"displayed ?

Yes

Check the pattern between pin 57 (PUIN) of IC701 and
BI803/CNS803.
Check the between BI803/CNS803 and PU-IN switch.

Check the procedure in "HF ERROR".

Check the procedure in "TRACK SEARCH FAILUR".

Check the procedure in "SLED SERVO FAILURE".

No

Check the procedure in

No

"SLED MOTOR
OPERATING FAILURE ".

Is "PU ERROR" displayed?

Yes

XL-530H,CP-XL530H

• Laser failure.

Is +6.2V applied to the emiter of Q861 ?

Yes

Is +5V applied to the collector of Q861 ?

Yes

Is +5V applied to the pin 62 (VDD) of IC802 ?

Yes

Is +5V applied to the pin 1 (VCC) of Ic801 ?

Yes

Is 0V applied to the pin 57 (SEL) of IC802 ?

Yes

Is approx. 2V applied to the collector of Q801.

Yes

No

No

No

No

No

No

No

Check the PWB pattern between pin 16 of CNS602 and emiter of
Q861.

Check the peripheral parts of IC804 and Q861.

Check the PWB pattern between collector of Q861 and pin 62 of
IC802.

Check the PWB pattern between collector of Q861 and pin 1 of
IC801.

Does the laser come on when pattern cut between pin 8 (SEL) of
IC801 and pin 57 (SEL) of IC802 ?

Yes

Check the PWB pattern between IC701 and IC802 (BUCK/CCE/
BUS0~3)

Check the peripheral parts of IC801 and Q801. If it is normal, the
optical pickup is faulty.

Check BI802/CNS802. If it is normal, the optical pickup is
faulty.

• Focus failure.

Does the optical pickup move up and down when the disc is
removed?

Yes

Is the following waveform ouput at the pin 43 (FEI) of IC802
when the disc is set?

Yes

pin 43
(FEI)

pin 48
(FOO)

pin 44
(SBAD)

Is the waveform shown above input at the pin 44 (SBAD) of
IC802?

Yes

No

No

No

Check as stated in item "FOCUS SERVO SAWTOOTH WAVE
FAILURE".

Check the periphery of IC801 and BI802/CNS802. Is it normal?

Yes

The optical pickup is faulty.

Check the pattern between pin 13 of IC801 and pin 44 of IC802.
Check the periphery of IC801 and BI802/CNS802.

IC801 is faulty.

– 30 –

• Focus servo sawtooth wave failure.

XL-530H,CP-XL530H

Is sawtooh wave output to the pin 48 (FOO) of IC802 ?

Yes

1.5~2.5sec

Is +6.2V applied to the pins 1 and 30 (VCC) of IC804 ?

Yes

Is sawtooth wave obtained between pins 25 and 26 of IC804 ?

Yes

1.5~2.5sec

Is sawtooth wave obtained between pins 3 and 4 of BI801/
CNS801 ? (as shown above)

Yes

BI801/CNS801 connection failure or optical pickup failure.

No

No

No

No

IC802 is faulty.

Check the PWB pattern between pin 16 of CNS602 and IC804.

Is +5V applied to the pin 2
(MUTE) of IC804 ?

Yes

Check the PWB pattern
between pin 2 of IC804

No

and pin 58 (CD STB) of
IC701.

Check the PWB pattern between pin 48 (FOO) of IC802 and pins
27 and 28 of IC804. If OK. IC804 is faulty.

Check the PWB pattern between BI801/CNS801 and IC804.

• Spindle motor clv servo failure.

Is following wave output to the pin 55 (DMO) of IC802 when
the CD TEST MODE "STEP 3" is changed to " STEP 4" ?

Yes

DMO

Is above wave obtained between pins 5 and 6 of IC804 ?

Yes

Is above wave obtained between pins 5 and 6 of BI801/
CNS801 ?

Yes

BI801/CNS801 connection failure or optical pickup failure.

No

No

No

Check the procedure in "HF ERROR".
If OK. IC802 is faulty.

Check the PWB pattern between pin 55 (DMO) of IC802 and pins
5 and 6 of IC804. If OK. IC804 is faulty.

Check the PWB pattern between BI801/CNS801 and IC804.

– 31 –

XL-530H,CP-XL530H

• HF error.

Is output (tracking error signal) obtained at the pins 46 (TEI)
and 47 (TEZI) of IC802 the CD TEST MODE "STEP 4" is
changed to "STEP 5"?

Yes

test mode "step 4" test mode "step 5"

TEI

TEZI

Is output (HF signal) obtained at the pin 38 (RFI) of IC802
when the CD TEST MODE "STEP 4" is changed to "STEP 5"?

Yes

test mode "step 4" test mode "step 5"

RFI

No

No

5 of BI802/CNS802

Check the periphery of IC801.
Check the PWB pattern between
pin 12.
(TEO) of IC801 and pins 46 and 47
of IC802.
Is it normal ?

Check the PWB pattern between pin 50 (TEO) of IC802 and pin 18
of IC804.
Check the periphery of IC804 and BI801/CNS801.
If OK. Optical pickup failure.

Is output obtained at the pins 1 and
3, 4 of BI802/CNS802.

Check the periphery of IC801.
Check the PWB pattern between pin 19 (RFGO) of IC801 and pins
38 (RFI) of IC802.
If OK. IC801 is faulty

Is output obtained at the pins 2 and

Optical pickup failure.

No

Yes

IC801 is faulty.

No

Yes

Optical pickup failure.

No

Yes

Is output (HF signal) obtained at the pins 41 (RFZI) and 42
(RFRP) of IC802 when the CD TEST MODE "STEP 4" is
changed to "STEP 5"?

Yes

test mode "step 4" test mode "step 5"

RFZI

RFRP

Is the following wave output to the pin 55 (DMO) of IC802
when the CD TEST MODE "STEP 4" or "STEP 5"?

Yes

test mode "step 4" test mode "step 5"

DMO

Normal.

• No sound.

No sound from both L and R-ch?

Yes

No

No

No

Check the periphery of IC801.
Check the PWB pattern between pin17 (RFRP) of IC801 and pins
41 (RFZI) and 42 (RFRP) of IC802.
If OK. IC801 is faulty.

Check the periphery pins 28~32 of IC802.
If OK. IC802 failure.

Check the interval between the pins 82 or 85 of IC802 and the pins
1 or 3 IC601.

Is +4.5V applied to pin 83 (DVDD) of IC802?

Yes

Is signal of pins 82 and 85 of IC802 output?

Yes

The main PWB is faulty.

No

No

– 32 –

Check the PWB pattern between R819 and Q861.

Check the peripheral parts of IC802. If OK, IC802 is faulty.

• Track search failure

XL-530H,CP-XL530H

Does the sled motor run in FF/REW state when the SERVO
TEST MODE "STEP1" is set?

Yes

Is the following wave output to the pin 49 (TRO) of IC802
during track search in normal playback?

Yes

TRO

Is the following wave output to the pins 12 (TEO) of IC801
during track search in normal playback?

Yes

TEO

TEI

TEZI

Is the above wave output to the pins 46 (TEI) and 47 (TEZ) of
IC802 during track serch in normal playback?

Yes

Is the following wave output to the pin 41 (RFZI) and 42
(RFRP) of IC802 during track search in normal playback?

Yes

RFRP

RFZI

No

No

No

No

No

Check as stated in item "SLED MOTOR OPERATION FAILURE".

IC802 failure.

Check the PWB pattern between pin 49 (TRO) of IC802 and pin
18 of IC804.
Check the PWB pattern between pins 20 and 21 of IC804 and
Optical pickup.
If OK. Optical pickup failure.

Check the PWB pattern between pin 12 (TEO) of IC801 and pins 46
and 47 of IC802. If OK. IC801 failure.

Check the PWB pattern between pin 17 (RFO) and 18 (RFIS), 19
(RFRP) of IC801 and pins 41 and 42 of IC802. If OK. IC801 failure.

Normal.

• Sled motor operation failure.

Is following sled feed signal output the pin 53 (FMO) of IC802
when FF/REW key is pressed after the CD TEST MODE
"STEP 1" is seted?

Yes

Is following sled feed signal output the pins 12 and 13 of
IC804 when FF/REW key is pressed after the CD TEST
MODE "STEP 1" is seted?

Yes

Is sled feed signal output the pins 10 and 11 of IC804?

Yes

Is sled feed voltage applied between both terminals of sled
motor?

Yes

Check the CD mechanism (periphery of sled motor).
If the sled motor does not run when DC2.0V is applied to
both terminals of sled motor, the sled motor is faulty.

FF REW

FMO

FF REW

SL ±

No

No

No

No

C801 is faulty.

Check the PWB pattern between pin 53 of IC802 and pins 12 and
13 of IC804.

Check the peripheral parts of IC804. If OK, IC804 is faulty.

Check the BI803/CNS803.

• Sled servo failure.

Is following sled signal output the pin 53 (FMO) of IC802
during playback?

Yes

FMO

Normal.

No

IC802 is faulty.

– 33 –

XL-530H,CP-XL530H

FUNCTION TABLE OF IC

IC401 VHiM62495FP-1: Audio Processor (M62495FP)

Pin No. Port Name Function

1 IN A1 It is the input terminal of the channel 1
2 IN B1 It is the input terminal of the channel 1
3 IN C1 It is the input terminal of the channel 1
4* IN D1 It is the input terminal of the channel 1
5* IN E1 It is the input terminal of the channel 1

6 SELO1 Selector COM output terminal of channel 1
7 VOLI1 Volume input terminal of channel 1
8 TONEH1 Channel 1 treble frequency adjusting terminal
9 TONEL1 Channel 1 bass frequency, gain adjusting terminal
10 OUT1 Channel 1 output terminal
11 GND GND terminal
12 VDD Positive power terminal
13 CONT Microcomputer data input terminal
14 VSS Negative power terminal
15 OUT1 Channel 2 output terminal
16 TONEL2 Channel 2 bass frequency, gain adjusting terminal
17 TONEH2 Channel 2 treble frequency adjusting terminal
18 VOLI2 Volume input terminal of channel 2
19 SELO2 Selector COM output terminal of channel 2
20* IN E2 It is the input terminal of the channel 2.

21* IN D2 Input terminal of channel 2
22 IN C2 Input terminal of channel 2
23 IN B2 Input terminal of channel 2
24 IN A2 Input terminal of channel 2

Independent control (from chA to D) is possible. Simultaneous ON use is enabled.
When only chE is set to on, set Selector ALL OFF mode

Independent control (from chA to D) is possible. Simultaneous ON use is enabled.
When only chE is set to on, set Selector ALL OFF mode.

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

IC401 VHiM62495FP-1: Audio Processor (M62495FP)

INA2

24 23 22 21 20 19 18 17 16 15 14 13

Input SW

123456789101112

INA1

INB2

Monophonic

SW

INB1

INC2

INC1

IND2

MUTE

IND1

INE2

5k

5k

INE1

14dB

14dB

SELOUT2

Volume

SELOUT1

VOLIN2

30k

30k

VOLIN1

Figure 34 BLOCK DIAGRAM OF IC

TONEH2

21.6k

2.4k

2.4k

21.6k

Treble

boost

TONEH1

TONEL2

46k

46k

TONEL1

OUT 2

Bass

boost

OUT 1

VSS

GND

CONT

Control Logic

VDD

– 34 –

XL-530H,CP-XL530H

IC701 RH-iX0015SJZZ: System Microcomputer (iX0015SJ) (1/2) (Serial No. 904xxxxx)
IC701 RH-iX0022SJZZ: System Microcomputer (iX0022SJ) (1/2) (Serial No. 905xxxxx~)

Pin No.

1-4 COM3-COM0 Output LCD common output terminal
5-7 VLC3-VLC1 — LCD power terminal
8 VDD — Microcomputer power +5V
9 OSC2 Output Main clock oscillator connection terminal f=8MHz
10 OSC1 Input An oscillation child connection terminal for the main clock f=8MHz
11 VSS — Microcomputer power GND
12 XI Input Sub-clock oscillator connection terminal f=32.768kHz
13 XO Output Sub-clock oscillator connection terminal f=32.768kHz
14 MMOD Input Memory mode selection terminal
15 VREF- — AD converter power GND
16 KEY0 AN0/PA0 Input Destination detection input Acts as an A/D input port.

17 KEY1 AN0/PA1 Input Operation button input, max. 8 buttons
18 KEY2 AN0/PA2 Input Operation button input, max. 8 buttons
19 KEY3 AN0/PA3 Input Model detection input H: XL-560/570 L: XL-540
20* KEY4 AN0/PA4 Input Tuner signal meter (S meter) voltage input terminal
21 KEY5 AN0/PA5 Input Cassette tape safety lug detection input

22 KEY6 AN0/PA6 Input Tape running/END detection input

23 KEY7 AN7/PA7 Input Cassette mechanism operation state detection input

24 VREF+ — A/D converter power +5V
25 TXD SBO0/P00 Output Terminal to output data to TUNER PLL IC
26 RXD SBI0/P01 Input Data input from TUNER PLL IC
27 SBT0/P02 Output Output of clock synchronizing with TUNER PLL IC
28 SBO1/P03 Output Terminal 1 to output data to VOL IC
29* SBI1/P04 —
30 SBT1/P05 Output POWER IC STANDBY terminal control
31 DK/BZER P06 Output Enable output of TUNER PLL IC "L" = OFF "H" = ON
32 RST/P27 Input Reset signal input
33 RMOUT Input CLOCK/TIMER/SLEEP button input
34 P11 Output Power mute output "H" = MUTE OFF "L" = MUTE ON
35 TM2IO P12 Output Main TRANS RELAY CONTROL "H" = ON "L" = OFF
36 TM3IO P13 Output CD servo power circuit control output "H" = CD power ON "L" = CD power OFF
37 TM4IO P14 Input Power button input detection
38 IRQ0 P20 Input Power failure detection input. When "L" is set, the mode is changed to HALT mode.
39 SENS IRQ1/P21 Input Remote control signal input
40* IRQ2 P22 Input Input of clock synchronizing with RDS IC
41 IRQ3 P23 Input Jog dial UP pulse input
42 IRQ4 Input Jog dial DOWN pulse input
43* P30 Input RDS signal reception state detection

44* P31 Input Data input from RDS IC
45 P32 Output TC9462F reset signal output
46 LED0 WE/P50 Output TC9462F chip enable terminal "L" = Bus terminal active
47 LED1 RE/P51 Output TC9462F data sync clock output
48 LED2 CS/P52 Output Tuner mute output "H" = Mute ON "L" = Mute OFF
49
50*
51 SEG49 P60/A0 Output Cassette mechanism solenoid drive control output
52 SEG48 P61/A1 Output Cassette mechanism motor drive control output

LDE3/S51 A16/P53
LED4/S50 A17/P54

Input/Output

When reset,it detects the destination setting according to DC voltage.

"H" = Record inhibited "L" = Record enabled

If pulse input is detected, it is judged that the tape is running.

"H" = Mechanism stopped "L" = Mechanism is operating

"H" = RDS not received "L" = RDS is being received

Output LCD backlight control signal output 1 Added "H" = Backlight ON "L" = Backlight OFF

—

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

FunctionTerminal Name

– 35 –

XL-530H,CP-XL530H

IC701 RH-iX0015SJZZ: System Microcomputer (iX0015SJ) (2/2) (Serial No. 904xxxxx)
IC701 RH-iX0022SJZZ: System Microcomputer (iX0022SJ) (2/2) (Serial No. 905xxxxx~)

Pin No.

Input/Output

53 SEG47 P62/A2 Output Tape circuit record/playback selection output "H" = Record mode "L" = Playback mode
54 SEG46 P63/A3 Output Record bias oscillation frequency selection control output
55 SEG45 P64/A4 Output Record bias oscillation circuit control output "H" = Bias oscillation "L" = Start stop
56 SEG44 P65/A5 Input CD lid state detection input "L" = Lid closed "H" = Lid opened
57 SEG43 P66/A6 Input CD pickup position detection SW input "L" = Innermost periphery
58 SEG42 P67/A7 Output CD servo control IC ON/OFF output terminal "H" = Servo ON "L" = Servo standby 2 Changed
59-62 SEG41 P70/A8- Input/Output TC9462F control data input/output terminal

SEG38 P73/A11
63* SEG37 P74/A12 Output SURROUND control output
64* SEG36 P75/A13 —
65 SEG35 P76/A14 Input Radio stereo broadcast reception detection input "L" = During stereo broadcast reception
66 SEG34 P77/A15 Input Broadcast reception state detection input "L" = During broadcast wave reception
67* SEG33 P87/D7 — LCD segment output.
68* SEG32 P86/D6 — LCD segment output.
69-73* SEG31 P85/D5- — LCD segment output

SEG27 P79/D1 Note:

Since RH-IX0015SJZZ is 24-pin LCD, SEG0 of LCD is connected to SEG7 of microcomputer
output terminal, with subsequent successive connection (up to SEG26).

74 SEG26 P80/D0 — LCD segment output

Note:
Since RH-IX0015SJZZ is 24-pin LCD, SEG0 of LCD is connected to SEG7 of microcomputer
output terminal, with subsequent successive connection (up to SEG26).

75-93 SEG25-SEG7 — LCD segment output

Note:
Since RH-IX0015SJZZ is 24-pin LCD, SEG0 of LCD is connected to SEG7 of microcomputer
output terminal, with subsequent successive connection (up to SEG26).

94-100* SEG8-SEG0 — LCD segment output

Note:
Since RH-IX0015SJZZ is 24-pin LCD, SEG0 of LCD is connected to SEG7 of microcomputer
output terminal, with subsequent successive connection (up to SEG26).

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

IC701 RH-iX0015SJZZ: System Microcomputer (iX0015SJ) (Serial No. 904xxxxx)

IC701 RH-iX0022SJZZ: System Microcomputer (iX0022SJ) (Serial No. 905xxxxx~)

FunctionTerminal Name

COM3
COM2
COM1
COM0

VLC3
VLC2
VLC1

VDD
OSC2
OSC1

VSS

XI

XO

MMOD

VREF­AREA

KEY1
KEY2

MODEL

VSM

F.P

RUN PLS

CAM-SW

VREF+

DI

SEG0

SEG1

SEG2

SEG3

SEG4

SEG5

SEG6

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

SEG13

SEG14

SEG15

SEG16

SEG17

SEG18

SEG19

SEG20

SEG21

SEG22

SEG23

CCE

BUCK

R-MUTE

SEG24

76

B-LIGHT

S

75

SEG25

S

74

SEG26

S

73

SEG27

S

72

SEG28

S

71

SEG29

S

70

SEG30

S

69

SEG31

S

68

SEG32

S

67

SEG33

I

66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

O
I/O
I/O
I/O
I/O

O

O

O

O

O

O

I

I
I

SD

STEREO

SURR
BUS3
BUS2
BUS1
BUS0

CD_STB

PU-IN

LID-SW

BIAS

B-CAN

REC

MOT

SOL

SSSSSSSSSSSSSSSSSSSSSSSSS

9998979695949392919089888786858483828180797877

100

1

O

2

O

3

O

4

O

5
6
7
8
9

O

10

I

11
12

I

13

O

14

I

15
16

I

17

I

18

I

19

I

20

I

21

I

22

I

23

I

24
25

O

26272829303132333435363738394041424344454647484950
I

OOOOO

CL

DO

VDO1

VDO2

P-STB

CE

I

I

RESET

CLOCK

OOO

P-MUTE

P-CONT

CD+B

IIIIIII

CLE

JOG UP

POWER

SYS STOP

REMOCON

JOG DOWN

ID

I

DATA

OOOOO

CD RES

Figure 36 BLOCK DIAGRAM OF IC

– 36 –

IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F)

XL-530H,CP-XL530H

Pin No.

Terminal Name

Input/Output

Function

1 VCC — Power voltage terminal
2 FNI Input Main beam amp input terminal
3 FPI Input Main beam amp input terminal
4 TPI Input Sub-beam amp input terminal
5 TNI Input Sub-beam amp input terminal
6 MDI Input Monitor photodiode amp input terminal
7 LDO Output Laser diode amp output terminal
8 SEL Input Laser diode control signal input and APC circuit ON/OFF signal input terminal
9 TEB Input Tracking error balance adjustment signal input terminal

To be controlled by 3-value PWM signal. (PWM carrier = 88.2 kHz)
10 2VRO Output Standard voltage (2VR) output terminal. When Vcc = 5V, 2VR = 4.2V.
11 TEN Input Tracking error signal generation amp reversed phase input terminal
12 TEO Output Tracking error signal generation amp output terminal
13 SBAD Output Sub-beam addition signal output terminal
14 FEO Output Focus error signal generation amp output terminal
15 FEN Input Focus error signal generation amp reversed phase input terminal
16 VRO Output Standard voltage (VR) output terminal. When Vcc = 5V, VR = 2.1V.
17 RFRP Output Track count signal generation amp output terminal
18 RFIS Input RFRP detection circuit input terminal
19 RFGO Output RF signal output terminal
20 RFGC Input RF amplitude adjustment control signal input terminal

The amplitude of RF signal can be controlled by using the 3-value PWM signal (PWM

carrier = 88.2 kHz) which is output from the RFGC terminal of TC9432F.
21 AGCI Input RF signal amplitude adjustment amp input terminal
22 RFO Output RF signal generation amp output terminal
23 GND — GND terminal
24 RFN Input RF reversed phase input terminal

IC801 VHiTA2109F/-1:Servo Pre Amp. (TA2109F)

SBAD

FEO

FEN

VRO

RFRP

RFIS

RFGO

RFGC

AGCI

RFO

GND

RFN

14

15

16

17

18

19

20

21

22

23

24

10pF

10kΩ

20kΩ

23.5kΩ

re = 130Ω

7.96kΩ

21kΩ 21kΩ

50µA

20kΩ

3.3kΩ

50kΩ

20kΩ

1.53kΩ

3.3kΩ

36pF

12kΩ
12kΩ

PEAK

BOTTOM

12kΩ

15kΩ
15kΩ

20µA

10kΩ

10kΩ
10kΩ

180kΩ

40pF

Figure 37 BLOCK DIAGRAM OF IC

30kΩ

30kΩ

21kΩ 29kΩ

24kΩ

1.74kΩ

65µA

180kΩ

20pF

180kΩ

20pF

40pF

180kΩ

24kΩ

47kΩ

SW

60kΩ

60kΩ

– 37 –

13kΩ

3

10kΩ

SW

7.67kΩ

3 STATE

DET.

SW

1

2

680kΩ

I . I

I . I

20kΩ

20kΩ

1kΩ

2.12kΩ

LDC

20pF

20kΩ

20kΩ

1213

11

10

9

8

7

6

5

4

3

2

1

TEO

TEN

2VRO

TEB

SEL

LDO

MDI

TNI

TPI

FPI

FNI

VCC

SEL

L

HiZ

H

SW1

ON
OFF
OFF

LDC

SW2

SW3

OFF OFF

ONONON

ON

XL-530H,CP-XL530H

IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (1/3)

Pin No.

1* TEST0 Input Test mode terminal. To be opened usually.
2* /HSO Output Playback speed mode flag output terminal.

3* /UHSO Output

4* EMPH Output Sub-code Q data emphasis flag output terminal. "H": Emphasis ON "L": Emphasis OFF

5* LRCK Output Channel clock (44.1 kHz) output terminal. "L": L channel "H": R channel

6 VSS — Digital ground terminal.
7 BCK Output Bit clock (1.4122 MHz) output terminal.
8* AOUT Output Audio data output terminal.
9* DOUT Output Digital out output terminal.
10* MBOV Output Buffer memory over signal output terminal. "H": Over
11* IPF Output Correction flag output terminal.

12* SBOK Output Sub-code Q data CRCC judgment result output terminal. "H": When judgment result is OK.
13* CLCK Input/Output Sub-code P-W data read clock output/input terminal. Selectable with command bit.
14 VDD — Digital + power terminal.
15 VSS — Digital ground terminal.
16* DATA Output Sub-code P-W data output terminal.
17* SFSY Output Playback system frame sync signal output terminal.
18* SBSY Output Sub-code block sync output terminal. "H": On S1 position when the sub-code sync is detected.
19* SPCK Output Processor status signal read clock (176.4 kHz) output terminal.
20* SPDA Output Processor status signal output terminal.
21* COFS Output Correction system frame clock (7.35 kHz) output terminal.
22* MONIT Output LSI internal signal monitor terminal.

23 VDD — Digital + power terminal.
24 TESIO0 Input Test input/output terminal. To be fixed to "L" usually.

25 P2VREF — 2VREF terminal for PLL system.
26* HSSW Output VREF voltage in case of x2 speed/x4 speed.
27* ZDET Output 1-bit DAC zero detection flag output terminal.
28 PDO Output Terminal to output the phase difference between EFM signal and PLCK signal.
29* TMAXS Output TMAX detection result output terminal. To be selected with command bit TMPS.
30 TMAX Output TMAX detection result output terminal. To be selected with command bit TMPS.

Port Name

Input/Output

/UHSO

H H x1 speed playback
H L x2 speed playback
L H x4 speed playback
LL—

The output polarity can be inverted by command.

The output polarity can be inverted by command.

"H": When AOUT output is correction-disabled symbol in case of C2 correction output.

It is possible to monitor the DSP internal flag and PLL system clock with the microcomputer
command. Terminal for serial output of text data according to command.

Terminal to input the text data read clock according to command.

/HSO

TMAX detection result

Longer than specific period "P2VREF"
Shorter than specific period "VSS"
Within specific period "HIZ"

31 LPFN Input Low-pass filter amp inverted input terminal.
32 LPFO Output Low-pass filter amp output terminal.
33 PVREF — VREF terminal for PLL system.
34 VCOREF Input VCO center frequency standard level terminal. To be fixed to PVref usually.
35 VCOF Output VCO filter terminal.
36 AVSS — Analog system ground terminal.
37 SLCO Output Data slice level generation DAC output terminal.
38 RFI Input RF signal input terminal.

Function

Playback speed

TMAX output

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

– 38 –

IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (2/3)

XL-530H,CP-XL530H

Pin No.

39 AVDD — Analog system power terminal.
40 RFCT Input RFRP signal center level input terminal.
41 RFZI Input RFRP zero cross input terminal.
42 RFIP Input RF ripple signal input terminal.
43 FEI Input Focus error signal input terminal.
44 SBAD Input Sub-beam addition signal input terminal.
45 TSIN Input Test input terminal. To be fixed to Vref usually.
46 TEI Input Tacking error input terminal. (Tracking servo ON: Taking-in).
47 TEZI Input Tracking error, zero cross input termina.l
48 FOO Output Focus equalizer output terminal.
49 TRO Output Tracking equalizer output terminal.
50 VREF — Analog standard power terminal.
51 RFGC Output RF amplitude adjustment control signal output terminal.

52 TEBC Output Tracking balance control signal output terminal.

53 FMO Output Feed equalizer output terminal. 3-value PWM signal is output. (PWM carrier = 88.2 kHz)
54* FVO Output Speed error signal or feed search EQ output terminal.

55 DMO Output Disc equalizer output terminal.

56 2VREF — Analog standard power terminal (2xVREF)
57 SEL Output APC circuit ON/OFF signal output terminal.

58* FLGA Output Internal signal monitor external flag output terminal.

59* FLGB Output Internal signal monitor external flag output terminal.

60* FLGC Output Internal signal monitor external flag output terminal.

61* FLGD Output Internal signal monitor external flag output terminal.

62 VDD — Digital + power terminal.
63 VSS — Digital ground terminal.
64* IO0 Input/Output General-use I/O port.

65* IO1 The input port and output port can be selected with command. In case of input port the terminal
66* IO2 state (H/L) can be read with the read command.
67* IO3 In case of output port the terminal state (H/L/HiZ) can be controlled with command.

68* /DMOUT Input Terminal to set the mode to output 2-value PWM of feed equalizer from IO0,1 terminal and 2-

69* /CKSE Input To be opened usually.
70* /DACT Input DAC test mode terminal. To be opened usually.
71 TESIN Input Test input terminal (externally provided VCO clock input terminal). To be fixed to "L" usually.
72 TESIO1 Input Test input/output terminal. To be fixed to "L" usually.
73 VSS — Digital ground terminal.
74 PXI Input DSP system clock oscillation circuit input terminal. To be fixed to "L" usually.
75* PXO Output DSP system clock oscillation circuit output terminal.
76 VDD — Digital + power terminal.
77 XVSS — System clock oscillation circuit ground terminal.
78 XI Input System clock oscillation input terminal.
79 XO Output System clock oscillation circuit output terminal.
80 XVDD — System clock oscillation circuit + power terminal.
81 DVSR — R channel D/A converting section power terminal.
82 RO Output R channel data forward rotation output terminal.

Port Name

Input/Output

3-value PWM signal is output. (PWM carrier = 88.2 kHz)

3-value PWM signal is output. (PWM carrier = 88.2 kHz)

3-value PWM signal is output. (PWM carrier = 88.2 kHz)

3-value PWM signal is output. (PWM carrier = DSP system 88.2 kHz, sync with PXO)

When laser is ON and UHS = L, "Hi-Z". When UHS = H, "H" output is obtained.

TEZC, FOON, FOK and RFZC signals can be selected with command.

DFCT, FOON, FMON and RFZC signals can be selected with command.

TRON, TRSR, FOK, and SRCH signals can be selected with command.

TRON, DMON, HYS and SHC signals can be selected with command.

value PWM of disc equalizer from IO2,3 terminal. "L" active

Function

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

– 39 –

XL-530H,CP-XL530H

IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F) (3/3)

Pin No.

Port Name

Input/Output

Function

83 DVDD — D/A converting section power terminal.
84 DVR — Reference voltage terminal.
85 LO Output L channel data forward rotation output terminal.
86 DVSL — L channel D/A converting section power terminal.
87* TEST1 Input Test mode terminal. To be opened usually.
88* TEST2 Input Test mode terminal. To be opened usually.
89* TEST3 Input Test mode terminal. To be opened usually.
90-93 BUS0-BUS3 Input/Output Microcomputer interface data input/output terminal.
94 VDD — Digital + power terminal.
95 VSS — Digital ground terminal.
96 BUCK Input Microcomputer interface clock input terminal.
97 /CCE Input Microcomputer interface chip enable signal input terminal. "L": BUS0 to 3 is active.
98* TEST4 Input Test mode termina. To be opened usually.
99* /TSMOD Input Local test mode selection terminal.
100 /RST Input Reset signal input terminal. "L": Reset.

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

IC802 VHiTC9462F/-1: Servo/Signal Control (TC9462F)

LPFN
LPFO

PVREF

VCOREF

VCOF

AVSS

SLCO

RFI

AVDD

RFCT

RFZI

RFRP

FEI

SBAD

TSIN

TEI
TEZI
FOO

TRO

VREF

TMAX

TMAXS

PDO

ZDET

HSSW

P2VREF

TESIO0

VDD

MONIT

COFS

SPDA

SPCK

SBSY

SFSY

DATA

VSS

VDD

CLCK

SBOK

IPF

MBOV

DOUT

AOUT

BCK

VSS

LRCK

EMPH

/UHSO

/HSO

15

1718

Sub-code

demodulation

circuit

16

22232425 21272829 2030 26

31
32
33
34

PLL

TMAX

VCO

Status

19 10

Digital

out

11

121314

Audio output

circuit

35
36
37
38
39

Data

slicer

CLV

servo

Synchronizing

signal guarantee

EFM demodulation

40
41
42
43

A/D

Digital equalizer

adjustment circuit

44

RAM

ROM

16KRAM

Address

circuit

Correction

circuit

Microcomputer

interface

45
46
47
48
49

D/A

PWM

Servo control

Clock

generator

1Bit

DAC

LPF

50

RFGC

TEBC

FMO

FVO

DMO

56

2VREF

SEL

58

FLGA

59

FLGB

60

FLGC

61

FLGD

VDD

VSS

IO0

IO1

6652 53 54 5551 57

IO2

67 68 69

IO3

/DMOUT

/CKSE

/DACT

71

TESIN

72

TESIO1

73 74 75

PXI

VSS

PXO

VDD

77 78 7970807662 63 64 65

XVSS

TEST0

2345 1789 6

100

/RST

99

/TSMOD

98

TEST4

97

/CCE

96

BUCK

95

VSS

94

VDD

93

BUS3

92

BUS2

91

BUS1

90

BUS0

89

TEST3

88

TEST2

87

TEST1

86

DVSL

85

LO

84

DVR

83

DVDD

82

RO
DVSR

81

XI

XO

XVDD

Figure 40 BLOCK DIAGRAM OF IC

– 40 –

IC804 VHiLA6541D/-1: Focus/Tracking/Spin/Slide Driver (LA6541D)

Pin No. Port Name

1 VCC Power (short-circuited to pin 30)
2 MUTE All BTL AMP output ON/OFF
3 VIN1 BTL AMP1 input terminal
4 VG1 BTL AMP1 input terminal (for gain adjustment)
5 VO1 BTL AMP1 output terminal (noninversion side)
6 VO2 BTL AMP1 output terminal (inversion side)
7 GND GND terminal (lowest potential)
8 GND GND terminal (lowest potential)
9 GND GND terminal (lowest potential)
10 VO3 Output terminal of BTL AMP2 (inversion side)
11 VO4 Output terminal of BTL AMP2 (noninversion side)
12 VG2 Input terminal of BTL AMP2 (for gain adjustment)
13 VIN2 Input terminal of BTL AMP2
14 REG OUT Connect the collector of externally provided transistor (PNP). 5V power output
15 REG IN Connect the base of externally provided transistor (PNP).
16* RES Reset output
17* CD Reset output delay time setting (capacitor provided externally)
18 VIN3 Input terminal of BTL AMP3
19* VG3 Input terminal of BTL AMP3 (for gain adjustment)
20 VO5 Output terminal of BTL AMP3 (noninversion side)
21 VO6 Output terminal of BTL AMP3 (inversion side)
22 GND GND terminal (lowest potential)
23 GND GND terminal (lowest potential)
24 GND GND terminal (lowest potential)
25 VO7 Output terminal of BTL AMP4 (inversion side)
26 VO8 Output terminal of BTL AMP4 (noninversion side)
27 VG4 Input terminal of BTL AMP4 (for gain adjustment)
28 VIN4 Input terminal of BTL AMP4
29 VREF Application of standard voltage of level shift circuit
30 VCC Power (short-circuited to pin 1)

Function

XL-530H,CP-XL530H

*GND (lowest potential) is connected to the frame of pin center.

In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.

IC804 VHiLA6541D/-1: Focus/Tracking/Spin/Slide Driver (LA6541D)

26

Vo7

GND

GND

25 24 23 22 21

Vcc

4

1

VCC

30

Vref

29

VIN4

28 27

11kΩ

Level shift

Level shift

VG4

4

Vo8

BTL AMP

BTL AMP

1

11kΩ

1 2 3 4 5 6 7 8 9

VCC

Mute VIN1

VG1

Vo1

Vo2

GND GND GND

Figure 41 BLOCK DIAGRAM OF IC

GND

Vo6

Vo3

BTL AMP

BTL AMP

10

2

3

Vo5

20

11

Vo4

VG3

19

Level shift

Level shift

12 13 14

VG2

VIN3

18 17

11kΩ

3

2

11kΩ

Reg OUT

VIN2

CD

RESET

Regulator

RES

16

15

Reg IN

– 41 –

XL-530H,CP-XL530H

LCD701 RV-LX0004SJZZ: LCD Display

1

Z1

2

Z2

123456789

PinNo

1
2
3

com1
com1

com2

com2

Z3

3

o

9

r5

k

q4

q5

10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

com3

com3

com4

PinNo

13
14
15

com1

a4
g4

com2

f3

b4

j4

7

com3

e3
c4
k4

Z4

com4

RANDOM

d4
4
5
6
7
8
9

10
11
12

f2
a1
g1

i1

a2

m2

VOL

a3

e2
h1

j1
f1

b2

j2

b3

j3

EQ

b1

k1

e1

c2

n2

c3

p3

com4

16

17
c1
d1
z1
z2
d2

AUX

d3

Figure 42 LCD SEGMENT

18

19

20

21

22

23

24

AM
PM

a5
z3
a6

REC

b7
a7

SLEEP

f4

b5

f5

r5

b6

f6
j7
f7

kHz

e4

j5
e5
q5

j6
e6
c7
e7

MHz

q4

c5

d5

MEMORY

c6

d6

ST

d7

z4

– 42 –

PARTS GUIDE

XL-530H micro component system consisting of
XL-530H micro component system and CP­XL530H speaker system.

XL-530H,CP-XL530H

“HOW TO ORDER REPLACEMENT PARTS”

To have your order filled promptly and correctly, please furnish the
following information.

1. MODEL NUMBER 2. REF. No.

3. PART NO. 4. DESCRIPTION

MARK: SPARE PARTS-DELIVERY SECTION

Explanation of capacitors/resistors parts codes

Capacitors

VCC ....................... Ceramic type

VCK........................ Ceramic type

VCT........................ Semiconductor type

VC • • MF ............... Cylindrical type (without lead wire)

VC • • MN............... Cylindrical type (without lead wire)

VC • • TV................ Square type (without lead wire)

VC • • TQ ............... Square type (without lead wire)

VC • • CY ............... Square type (without lead wire)

VC • • CZ ............... Square type (without lead wire)

VC • • • • • • • • • J .. The 13th character represents capacity difference.

("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%,
"C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.)

If there are no indications for the electrolytic capacitors, error is ±20%.

MODEL

XL-530H
CP-XL530H

For U.S.A. only

Contact your nearest SHARP Parts Distributor to order.

For location of SHARP Parts Distributor,
Please call Toll-Free;
1-800-BE-SHARP

Resistors

VRD ....................... Carbon-film type

VRS........................ Carbon-film type

VRN ....................... Metal-film type

VR • • MF ............... Cylindrical type (without lead wire)

VR • • MN............... Cylindrical type (without lead wire)

VR • • TV................ Square type (without lead wire)

VR • • TQ ............... Square type (without lead wire)

VR • • CY ............... Square type (without lead wire)

VR • • CZ ............... Square type (without lead wire)

VR • • • • • • • • • J .. The 13th character represents error.

("J" ±5%, "F" ±1%, "D" ±0.5%.)

If there are no indications for other parts, the resistors are ±5%
carbon-film type.

NOTE:

Parts marked with “ ” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.

– 43 –

XL-530H,CP-XL530H

PARTS CODE NO. PARTS CODE

PRICE
RANK

DESCRIPTIONNO.

XL-530H

INTEGRATED CIRCUITS

IC101 VHIBA3126N/-1 J AF Head Selector,BA3126N
IC102 VHIBA3311L/-1 J AK Playback and Record/

IC301 VHITA7358AP-1 J AG FM Front End,TA7358AP
IC302 VHILC72131/-1 J AP PLL Controller,LC72131
IC303 VHILA1832//-1 J AR FM IF DET./FM MPX./AM IF,

IC401 VHIM62495FP-1 J AV Audio Processor,M62495FP
IC601 VHILA4600//-1 J AN Power Amp.,LA4600
IC701 RH-IX0015SJZZ J BD System Microcomputer,

IC701 RH-IX0022SJZZ J System Microcomputer,
IC801 VHITA2109F/-1 J AL Servo Pre Amp.,TA2109F

IC802 VHITC9462F/-1 J AZ Servo/Signal Control,TC9462F
IC804 VHILA6541D/-1 J AW Focus/Tracking/Spin/

Playback Amp.,BA3311L

LA1832

IX0015SJ [Serial No.904ЧЧЧЧЧ]
IX0022SJ[SerialNo.905ЧЧЧЧЧ~]

Slide Driver,LA6541D

TRANSISTORS

Q101~106 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q107 VSKRC104M//-1 J AC Digital,NPN,KRC104 M
Q151 VS2SC2001-K-1 J AD Silicon,NPN,2SC2001 K
Q152 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GR
Q153 VSKRC104M//-1 J AC Digital,NPN,KRC104 M
Q154,155 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q171 VSKRA102M//-1 J AC Digital,PNP,KRA102 M
Q172 VSKRC102M//-1 J AC Digital,NPN,KRC102 M
Q305,306 VS2SC535-C/-1 J AC Silicon,NPN,2SC535 C
Q351 VSKRC104M//-1 J AC Digital,NPN,KRC104 M
Q360 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GR
Q401 VS2SD468-C/-1 J AD Silicon,NPN,2SD468 C
Q601~603 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q604,605 VS2SD2012Y/-1 J AF Silicon,NPN,2SD2012 Y
Q606 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q607 VS2SD2012Y/-1 J AF Silicon,NPN,2SD2012 Y
Q608 VSKRA102M//-1 J AC Digital,PNP,KRA102 M
Q609 VSKRC107M//-1 J AC Digital,NPN,KRC107 M
Q681,682 VS2SD468-C/-1 J AD Silicon,NPN,2SD468 C
Q683 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q701 VSKRC102M//-1 J AC Digital,NPN,KRC102 M
Q702,703 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q705 VSKRA102M//-1 J AC Digital,PNP,KRA102 M
Q706 VSKRC102M//-1 J AC Digital,NPN,KRC102 M
Q707 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GR
Q801 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GR
Q861 VS2SB562-C/-1 J AD Silicon,PNP,2SB562 C
Q901 VSKRC102M//-1 J AC Digital,NPN,KRC102 M
Q902 VS2SB562-C/-1 J AD Silicon,PNP,2SB562 C
Q903 VSKRC107M//-1 J AC Digital,NPN,KRC107 M
Q904 VSKRC102M//-1 J AC Digital,NPN,KRC102 M
Q905 VS2SB562-C/-1 J AD Silicon,PNP,2SB562 C
Q906 VSKRA102M//-1 J AC Digital,PNP,KRA102 M

DIODES

D101,102 VHD1N4148//-1 J AA Silicon,1N4148
D104~106 VHD1N4148//-1 J AA Silicon,1N4148
D301,302 VHD1N4148//-1 J AA Silicon,1N4148
D305,306 VHD1N4148//-1 J AA Silicon,1N4148
D601~604 VHD1N4148//-1 J AA Silicon,1N4148

! D651~654 VHD1N4004//-1 J AB Silicon,1N4004
! D681~684 VHD1N4004//-1 J AB Silicon,1N4004

D685 VHD1N4004//-1 J AB Silicon,1N4004
D704~709 VHPL1154GDA-1 J AD LED,Green,L1154GDA
D718 VHD1N4004//-1 J AB Silicon,1N4004
D720~723 VHD1N4148//-1 J AA Silicon,1N4148
D901~904 VHD1N4148//-1 J AA Silicon,1N4148
VD301 VHCKV1236Z23F J AS Variable Capacitance,

VD302,303 VHCKDV147C/-1 J AH Variable Capacitance,KDV147C
ZD351 VHEMTZJ5R1B-1 J AC Zener,5.1V,MTZJ5.1B
ZD401 VHEMTZJ5R6B-1 J AD Zener,5.6V,MTZJ5.6B
ZD601 VHEMTZJ130A-1 J AC Zener,13V,MTZJ13A
ZD602 VHEMTZJ7R5C-1 J AC Zener,7.5V,MTZJ7.5C
ZD681 VHEMTZJ6R8A-1 J AA Zener,6.8V,MTZJ6.8A

KV1236Z23F

PRICE

RANK

ZD682 VHEMTZJ5R6B-1 J AD Zener,5.6V,MTZJ5.6B
ZD701 VHEMTZJ3R3B-1 J AA Zener,3.3V,MTZJ3.3B

DESCRIPTION

FILTERS

BF301 RFILR0008AWZZ J AE Band Pass Filter
CF302,303 RFILF0004SJZZ J AG FM RF,10.7 MHz
CF351 RFILF0003AWZZ J AK FM IF
CF352 RFILA0003SJZZ J AF AM IF
X351 RCRM-0007SJZZ J AG VCO,456 kHz

TRANSFORMERS

T302 RCILA0007SJZZ J AG AM Antenna
T304 RCILI0005SJZZ J AF FM IF
T306 RCILB0009SJZZ J AG AM Oscillation
T351 RCILI0004SJZZ J AF AM IF

! T651 RTRNP0024SJZZ J BC Power,Main
! T681 RTRNP0025SJZZ J AU Power,Sub

COILS

L151 VP-MK331K0000 J AB 330 µH,Choke
L302 RCILR0003SJZZ J AD FM RF
L303 RCILB0010SJZZ J AG FM Oscillation
L351,352 VP-DH101K0000 J AB 100 µH,Choke
L353 VP-DH102K0000 J AB 1 mH,Choke
L701 VP-DH101K0000 J AB 100 µH,Choke

! LF651 RCILZ0002SJZZ J AG Line Filter

VARIABLE RESISTOR

VR351 RVR-M0999AFZZ J AB 10 kohm (B),Semi-VR

[FM Mute Level]

VIBRATORS

X352 RCRSP0003SJZZ J AL Crystal,4.5 MHz
X701 RCRM-0008SJZZ J AG Ceramic,8 MHz
X702 RCRSP0011AWZZ J AC Crystal,32.768 kHz
X801 RCRM-0002SJZZ J AE Ceramic,16.93 MHz

CAPACITORS

C101,102 VCKYTV1HB102K J AA 0.001 µF,50V
C103,104 VCKYTV1HB331K J AA 330 pF,50V
C105,106 VCKYTV1HB271K J AA 270 pF,50V
C107,108 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C109,110 VCQYKA1HM153J J AB 0.015 µF,50V,Mylar
C111,112 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C113,114 RC-GZA475AF1E J AB 4.7 µF,25V,Electrolytic
C115,116 VCKYTV1HB222K J AA 0.0022 µF,50V
C117 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C118 VCKYTV1EF223Z J AA 0.022 µF,25V
C119,120 VCKYTV1EF103Z J AA 0.01 µF,25V
C121,122 VCCSTV1HL820J J AA 82 pF,50V
C123 RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C124 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C125 RC-GZA107AF1E J AB 100 µF,25V,Electrolytic
C126 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic
C129,130 RC-GZA475AF1E J AB 4.7 µF,25V,Electrolytic
C151 VCKYTV1HB181K J AB 180 pF,50V
C152 VCKYTV1HB102K J AA 0.001 µF,50V
C153 VCQPKA2AA392J J AB 0.0039 µF,100V,Polypropylene
C154 VCQYKA1HM273J J AB 0.027 µF,50V,Mylar
C155 RC-GZA475AF1E J AB 4.7 µF,25V,Electrolytic
C156 VCKYPA1HF223Z J AB 0.022 µF,50V
C303 VCKYTV1HB102K J AA 0.001 µF,50V
C304 VCKYTV1EF103Z J AA 0.01 µF,25V
C305 VCKYTV1HB472K J AA 0.0047 µF,50V
C306 VCCUTV1HJ7R0D J AA 7 pF (UJ),50V
C307 VCKYTV1HB472K J AA 0.0047 µF,50V
C308 VCKYTV1EF223Z J AA 0.022 µF,25V
C309,310 VCKYTV1HB102K J AA 0.001 µF,50V
C311 VCCCTV1HH100J J AA 10 pF (CH),50V
C312 VCCSTV1HL330J J AA 33 pF,50V
C313 VCCUTV1HJ3R0C J AA 3 pF (UJ),50V
C314 VCCCTV1HH220J J AA 22 pF (CH),50V
C315 VCKYBT1HB101K J AA 100 pF,50V

– 1 –

XL-530H,CP-XL530H

NO. PARTS CODE

C316 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C317 VCKYTV1EF223Z J AA 0.022 µF,25V
C318 VCCSTV1HL5R0J J AA 5 pF,50V
C319 VCCCTV1HH180J J AA 18 pF (CH),50V
C323 VCKYTV1EF223Z J AA 0.022 µF,25V
C330 VCCUPA1HJ8R0D J AA 8 pF (UJ),50V
C331 VCKYTV1EF473Z J AB 0.047 µF,25V
C332,333 VCKYTV1EF223Z J AA 0.022 µF,25V
C334 VCCUTV1HJ180J J AA 18 pF (UJ),50V
C335 VCCCTV1HH180J J AA 18 pF (CH),50V
C336 VCKYTV1HB471K J AA 470 pF,50V
C337 VCKYTV1EF223Z J AA 0.022 µF,25V
C343 VCCSTV1HL330J J AA 33 pF,50V
C349 VCKYTV1EF223Z J AA 0.022 µF,25V
C350,351 VCKYTV1EF223Z J AA 0.022 µF,25V
C352 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C353,354 VCKYTV1EF223Z J AA 0.022 µF,25V
C355 VCCSTV1HL220J J AA 22 pF,50V
C356 VCKYTV1HB102K J AA 0.001 µF,50V
C357 RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C358 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C360,361 VCKYTV1EF223Z J AA 0.022 µF,25V
C362 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C363 VCKYPA1HF223Z J AB 0.022 µF,50V
C364 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C365 VCKYTV1EF223Z J AA 0.022 µF,25V
C366 VCKYTV1HB102K J AA 0.001 µF,50V
C367,368 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C369 VCCSTV1HL560J J AA 56 pF,50V
C370~372 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C373,374 VCTYPA1CX153K J AA 0.015 µF,16V
C380 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C381 VCCCTV1HH120J J AA 12 pF (CH),50V
C382 VCCCTV1HH150J J AA 15 pF (CH),50V
C383 VCTYBT1EF223Z J AA 0.022 µF,25V
C384 VCKYTV1HB102K J AA 0.001 µF,50V
C385 VCKYTV1HB103K J AA 0.01 µF,50V
C386 VCKYTV1HB331K J AA 330 pF,50V
C387 VCKYTV1EF223Z J AA 0.022 µF,25V
C388 VCKYPA1HB102K J AA 0.001 µF,50V
C391 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C392 VCKYTV1HB102K J AA 0.001 µF,50V
C393 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C394 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C395 VCKYTV1EF223Z J AA 0.022 µF,25V
C396 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C397 VCKYTV1EF223Z J AA 0.022 µF,25V
C398 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C399 VCKYPA1HF223Z J AB 0.022 µF,50V
C401~406 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C415~418 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C419,420 VCKYTV1HB333K J AA 0.033 µF,50V
C421~424 VCKYTV1EF224Z J AA 0.22 µF,25V
C425,426 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C428 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C430 RC-GZA477AF1A J AC 470 µF,10V,Electrolytic
C431 VCKYTV1HB101K J AA 100 pF,50V
C432 VCKYTV1EF223Z J AA 0.022 µF,25V
C433 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C434 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C601 RC-GZA336AF1C J AB 33 µF,16V,Electrolytic
C603,604 VCKYTV1HB102K J AA 0.001 µF,50V
C605,606 VCTYPA1CX473K J AA 0.047 µF,16V
C607 RC-GZA107AF1E J AB 100 µF,25V,Electrolytic
C608 RC-GZA226AF1E J AB 22 µF,25V,Electrolytic
C613,614 RC-GZV108AF1E J AD 1000 µF,25V,Electrolytic
C615 VCKYPA1HF223Z J AB 0.022 µF,50V
C616 RC-GZW478AF1E J AG 4700 µF,25V,Electrolytic
C620 RC-GZV477AF1E J AC 470 µF,25V,Electrolytic
C621 RC-GZA107AF1E J AB 100 µF,25V,Electrolytic
C622 VCKYPA1HF223Z J AB 0.022 µF,50V
C623 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C624 VCKYPA1HF223Z J AB 0.022 µF,50V
C625 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C626 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C627 VCKYTV1EF223Z J AA 0.022 µF,25V
C628 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic

! C651~654 VCFYDA1HA104J J AB 0.1 µF,50V,Thin Film

C660 VCKYPA1HF103Z J AB 0.01 µF,16V

! C681,682 VCFYDA1HA473J J AB 0.047 µF,50V,Thin Film

C683 RC-GZV228AF1C J AG 2200 µF,16V,Electrolytic
C684 VCFYDA1HA473J J AB 0.047 µF,50V,Thin Film

PRICE
RANK

DESCRIPTION

NO.

C685 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C686 VCKYPA1HF223Z J AB 0.022 µF,50V
C688 VCKYPA1HF223Z J AB 0.022 µF,50V
C689 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C695 VCKYPA1HB102K J AA 0.001 µF,50V
C696 VCKYPA1HF103Z J AB 0.01 µF,50V
C697 VCKYPA1HB102K J AA 0.001 µF,50V
C699 VCKYPA1HB102K J AA 0.001 µF,50V
C701,702 VCCCTV1HH220J J AA 22 pF (CH),50V
C703,704 VCKYTV1EF223Z J AA 0.022 µF,25V
C705,706 VCKYTV1HB102K J AA 0.001 µF,50V
C707 RC-GZA475AF1E J AB 4.7 µF,25V,Electrolytic

C710 VCKYTV1EF103Z J AA 0.01 µF,25V
C711 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C712 VCKYTV1EF103Z J AA 0.01 µF,25V
C713 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C714 VCKYTV1HB561K J AA 560 pF,50V
C715 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C801 VCCSPA1HL101J J AA 100 pF,50V
C802 VCKYTV1EB153K J AB 0.015 µF,25V
C803 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C804 VCKYTV1EB103K J AA 0.01 µF,25V
C805 VCKYTV1HB272K J AA 0.0027 µF,50V
C806 VCKYTV1HB472K J AA 0.0047 µF,50V
C807 VCKYTV1EB333K J AB 0.033 µF,25V
C809,810 VCKYTV1HB102K J AA 0.001 µF,50V
C811 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C812 VCKYTV1EF103Z J AA 0.01 µF,25V
C813 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C817~819 VCKYTV1EB104K J AA 0.1 µF,25V
C820 VCKYTV1EF103Z J AA 0.01 µF,25V
C821 VCKYTV1EB104K J AA 0.1 µF,25V
C822 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic
C823 VCKYTV1EF103Z J AA 0.01 µF,25V
C824,825 VCKYTV1EB563K J AA 0.056 µF,25V
C828,829 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C830 VCKYTV1EB563K J AA 0.056 µF,25V
C831,832 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C833,834 VCKYTV1HB471K J AA 470 pF,50V
C835 VCKYTV1EB563K J AA 0.056 µF,25V
C836 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C837 VCKYPA1HB471K J AA 470 pF,50V
C838 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C839 VCCSTV1HL2R0C J AA 2 pF,50V
C840,841 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C842 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C843 VCKYTV1EF104Z J AA 0.1 µF,25V
C844 VCKYTV1HB682K J AA 0.0068 µF,50V
C845 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C846,847 VCKYTV1EB104K J AA 0.1 µF,25V
C848 VCCSPA1HL390J J AA 39 pF,50V
C849 VCKYTV1EB563K J AA 0.056 µF,25V
C850 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic
C855 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C857 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C858 VCKYTV1EF103Z J AA 0.01 µF,25V
C859 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic
C860 VCKYTV1EF104Z J AA 0.1 µF,25V
C861 VCKYBT1HB102K J AA 0.001 µF,50V
C862 VCKYPA1HB102K J AA 0.001 µF,50V
C863 VCKYTV1HB221K J AA 220 pF,50V
C864 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C887 VCKYTV1HB102K J AA 0.001 µF,50V
C901 VCKYTV1HB102K J AA 0.001 µF,50V
C902 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C903 RC-GZA107AF1E J AB 100 µF,25V,Electrolytic
C904,905 VCKYPA1HF223Z J AB 0.022 µF,50V

PRICE
RANK

DESCRIPTIONPARTS CODE

[Serial No.904ЧЧЧЧЧ Only]

RESISTORS

R70A,B VRS-TV2AB102J J AA 1 kohm,1/10W
R70C VRS-TV2AB332J J AA 3.3 kohms,1/10W
R70E VRS-TV2AB104J J AA 100 kohm,1/10W
R70F VRS-TV2AB820J J AA 82 ohms,1/10W
R70G VRS-TV2AB102J J AA 1 kohm,1/10W
R70H,J VRS-TV2AB103J J AA 10 kohm,1/10W
R70K VRS-TV2AB121J J AA 120 ohms,1/10W
R70L VRS-TV2AB102J J AA 1 kohm,1/10W
R70M VRD-ST2CD101J J AA 100 ohm,1/6W

VRS-TV2AB000J J AA 0 ohm,Jumper,1.25×2mm,Green

– 2 –

XL-530H,CP-XL530H

PARTS CODE NO. PARTS CODE

R80A,B,C VRS-TV2AB823J J AA 82 kohms,1/10W
R80E VRD-ST2CD823J J AA 82 kohms,1/6W
R80F VRS-TV2AB823J J AA 82 kohms,1/10W
R80G VRD-ST2CD823J J AA 82 kohms,1/6W
R101,102 VRD-ST2CD102J J AA 1 kohm,1/6W
R103,104 VRS-TV2AB121J J AA 120 ohms,1/10W
R105 VRS-TV2AB154J J AA 150 kohms,1/10W
R106 VRD-ST2CD154J J AA 150 kohms,1/6W
R107 VRD-ST2CD103J J AA 10 kohm,1/6W
R108 VRS-TV2AB103J J AA 10 kohm,1/10W
R109,110 VRS-TV2AB392J J AA 3.9 kohms,1/10W
R111 VRD-ST2EE222J J AA 2.2 kohms,1/4W
R112 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R113,114 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R115,116 VRS-TV2AB153J J AA 15 kohms,1/10W
R117,118 VRS-TV2AB223J J AA 22 kohms,1/10W
R119,120 VRS-TV2AB101J J AA 100 ohm,1/10W
R121~124 VRS-TV2AB472J J AA 4.7 kohms,1/10W
R125 VRS-TV2AB104J J AA 100 kohm,1/10W
R126 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R127,128 VRS-TV2AB392J J AA 3.9 kohms,1/10W
R129,130 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R131 VRD-ST2CD472J J AA 4.7 kohms,1/6W
R132 VRS-TV2AB472J J AA 4.7 kohms,1/10W
R133 VRS-TV2AB102J J AA 1 kohm,1/10W
R134 VRS-TV2AB104J J AA 100 kohm,1/10W
R135 VRS-TV2AB684J J AA 680 kohms,1/10W
R136 VRS-TV2AB103J J AA 10 kohm,1/10W
R137 VRS-TV2AB472J J AA 4.7 kohms,1/10W
R138 VRD-ST2EE331J J AA 330 ohms,1/4W
R139 VRD-ST2EE272J J AA 2.7 kohms,1/4W
R140 VRS-TV2AB103J J AA 10 kohm,1/10W
R141 VRD-ST2CD331J J AA 330 ohms,1/6W
R151 VRS-TV2AB473J J AA 47 kohms,1/10W
R152 VRS-TV2AB104J J AA 100 kohm,1/10W
R153,154 VRS-TV2AB103J J AA 10 kohm,1/10W
R155 VRD-ST2EE560J J AA 56 ohms,1/4W
R156,157 VRD-ST2EE151J J AA 150 ohms,1/4W
R159,160 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R301 VRD-ST2EE220J J AA 22 ohms,1/4W
R302 VRS-TV2AB104J J AA 100 kohm,1/10W
R303 VRS-TV2AB333J J AA 33 kohms,1/10W
R304 VRD-ST2CD473J J AA 47 kohms,1/6W
R305 VRS-TV2AB681J J AA 680 ohms,1/10W
R306 VRS-TV2AB100J J AA 10 ohm,1/10W
R307 VRD-ST2EE470J J AA 47 ohms,1/4W
R308 VRS-TV2AB103J J AA 10 kohm,1/10W
R309 VRD-ST2EE471J J AA 470 ohms,1/4W
R310 VRS-TV2AB472J J AA 4.7 kohms,1/10W
R311 VRD-ST2CD331J J AA 330 ohms,1/6W
R312 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R313 VRS-TV2AB681J J AA 680 ohms,1/10W
R314,315 VRS-TV2AB330J J AA 33 ohms,1/10W
R319 VRS-TV2AB104J J AA 100 kohm,1/10W
R320 VRD-ST2EE330J J AA 33 ohms,1/4W
R321 VRD-ST2EE220J J AA 22 ohms,1/4W
R323 VRS-TV2AB683J J AA 68 kohms,1/10W
R324 VRS-TV2AB104J J AA 100 kohm,1/10W
R336 VRD-ST2CD472J J AA 4.7 kohms,1/6W
R350 VRS-TV2AB272J J AA 2.7 kohms,1/10W
R351 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R352 VRS-TV2AB102J J AA 1 kohm,1/10W
R353 VRS-TV2AB271J J AA 270 ohms,1/10W
R355 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R356 VRS-TV2AB102J J AA 1 kohm,1/10W
R357 VRS-TV2AB474J J AA 470 kohms,1/10W
R358 VRS-TV2AB822J J AA 8.2 kohms,1/10W
R359 VRD-ST2CD182J J AA 1.8 kohms,1/6W
R360 VRD-ST2CD472J J AA 4.7 kohms,1/6W
R361,362 VRS-TV2AB123J J AA 12 kohms,1/10W
R363 VRD-ST2CD682J J AA 6.8 kohms,1/6W
R364 VRS-TV2AB682J J AA 6.8 kohms,1/10W
R365 VRS-TV2AB103J J AA 10 kohm,1/10W
R371~374 VRD-ST2CD102J J AA 1 kohm,1/6W
R376 VRD-ST2CD103J J AA 10 kohm,1/6W
R377 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R379 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R380 VRD-ST2CD152J J AA 1.5 kohms,1/6W
R381 VRS-TV2AB103J J AA 10 kohm,1/10W
R382 VRD-ST2EE331J J AA 330 ohms,1/4W
R383 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R384 VRD-ST2CD682J J AA 6.8 kohms,1/6W

PRICE
RANK

DESCRIPTIONNO.

PRICE

RANK

R385 VRD-ST2CD562J J AA 5.6 kohms,1/6W
R386 VRD-ST2EE331J J AA 330 ohms,1/4W
R387 VRD-ST2CD562J J AA 5.6 kohms,1/6W
R391,392 VRD-ST2EE391J J AA 390 ohms,1/4W
R393 VRS-TV2AB102J J AA 1 kohm,1/10W
R395 VRS-TV2AB473J J AA 47 kohms,1/10W
R415~420 VRS-TV2AB152J J AA 1.5 kohms,1/10W
R423~428 VRS-TV2AB473J J AA 47 kohms,1/10W
R435,436 VRS-TV2AB103J J AA 10 kohm,1/10W
R437,438 VRS-TV2AB682J J AA 6.8 kohms,1/10W
R439,440 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R441,442 VRS-TV2AB391J J AA 390 ohms,1/10W
R443 VRS-TV2AB123J J AA 12 kohms,1/10W
R444,445 VRD-ST2EE221J J AA 220 ohms,1/4W
R446 VRD-ST2EE820J J AA 82 ohms,1/4W
R447 VRD-ST2EE471J J AA 470 ohms,1/4W
R448 VRD-ST2EE221J J AA 220 ohms,1/4W
R449 VRS-TV2AB103J J AA 10 kohm,1/10W
R450 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R451~453 VRD-ST2EE221J J AA 220 ohms,1/4W
R601,602 VRS-TV2AB103J J AA 10 kohm,1/10W
R603,604 VRS-TV2AB102J J AA 1 kohm,1/10W
R607 VRS-TV2AB682J J AA 6.8 kohms,1/10W
R608 VRD-ST2EE102J J AA 1 kohm,1/4W
R615,616 VRS-TV2AB391J J AA 390 ohms,1/10W
R617 VRS-TV2AB333J J AA 33 kohms,1/10W
R619,620 VRD-ST2EE470J J AA 47 ohms,1/4W
R621 VRS-TV2AB223J J AA 22 kohms,1/10W
R623 VRS-TV2AB223J J AA 22 kohms,1/10W
R624 VRD-ST2EE102J J AA 1 kohm,1/4W
R625 VRS-TV2AB103J J AA 10 kohm,1/10W
R627 VRS-TV2AB103J J AA 10 kohm,1/10W
R628 VRD-ST2EE101J J AA 100 ohm,1/4W
R629 VRD-ST2EE821J J AA 820 ohms,1/4W
R634 VRD-ST2EE102J J AA 1 kohm,1/4W
R661,662 VRD-ST2EE331J J AA 330 ohms,1/4W
R680 VHHRXE030//-1 J AN 1 ohm,Semicondactor
R681 VRD-ST2CD470J J AA 47 ohms,1/6W
R682 VRD-ST2CD122J J AA 1.2 kohms,1/6W
R683 VRD-ST2CD470J J AA 47 ohms,1/6W
R684 VRD-ST2CD122J J AA 1.2 kohms,1/6W
R685 VRD-ST2CD103J J AA 10 kohm,1/6W
R686 VRD-ST2CD473J J AA 47 kohms,1/6W
R702A,B,C VRS-TV2AB820J J AA 82 ohms,1/10W
R703A,B,C VRS-TV2AB820J J AA 82 ohms,1/10W
R707 VRD-ST2CD103J J AA 10 kohm,1/6W
R708 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R709 VRS-TV2AB392J J AA 3.9 kohms,1/10W
R710 VRD-ST2CD272J J AA 2.7 kohms,1/6W
R711,712 VRD-ST2CD182J J AA 1.8 kohms,1/6W
R713 VRS-TV2AB103J J AA 10 kohm,1/10W
R714 VRS-TV2AB273J J AA 27 kohms,1/10W
R715 VRD-ST2CD103J J AA 10 kohm,1/6W
R716 VRS-TV2AB562J J AA 5.6 kohms,1/10W
R717 VRS-TV2AB392J J AA 3.9 kohms,1/10W
R718 VRD-ST2CD272J J AA 2.7 kohms,1/6W
R719,720 VRD-ST2CD182J J AA 1.8 kohms,1/6W
R721 VRD-ST2CD103J J AA 10 kohm,1/6W
R722 VRS-TV2AB103J J AA 10 kohm,1/10W
R723~725 VRS-TV2AB473J J AA 47 kohms,1/10W
R726 VRS-TV2AB102J J AA 1 kohm,1/10W
R727 VRS-TV2AB472J J AA 4.7 kohms,1/10W
R728 VRS-TV2AB102J J AA 1 kohm,1/10W
R729 VRS-TV2AB103J J AA 10 kohm,1/10W
R730~732 VRS-TV2AB102J J AA 1 kohm,1/10W
R734~739 VRS-TV2AB473J J AA 47 kohms,1/10W
R741~746 VRS-TV2AB102J J AA 1 kohm,1/10W
R747 VRS-TV2AB471J J AA 470 ohms,1/10W
R749~751 VRS-TV2AB102J J AA 1 kohm,1/10W
R752 VRD-ST2CD102J J AA 1 kohm,1/6W
R753 VRS-TV2AB102J J AA 1 kohm,1/10W
R754 VRD-ST2CD102J J AA 1 kohm,1/6W
R755~757 VRS-TV2AB102J J AA 1 kohm,1/10W
R759~761 VRS-TV2AB102J J AA 1 kohm,1/10W
R764~767 VRS-TV2AB102J J AA 1 kohm,1/10W
R769 VRS-TV2AB103J J AA 10 kohm,1/10W
R770~776 VRS-TV2AB102J J AA 1 kohm,1/10W
R777 VRS-TV2AB103J J AA 10 kohm,1/10W
R778~781 VRS-TV2AB102J J AA 1 kohm,1/10W
R784,785 VRS-TV2AB102J J AA 1 kohm,1/10W
R787 VRS-TV2AB473J J AA 47 kohms,1/10W
R788 VRD-ST2CD473J J AA 47 kohms,1/6W

DESCRIPTION

– 3 –

XL-530H,CP-XL530H

NO. PARTS CODE

R793,794 VRD-ST2CD473J J AA 47 kohms,1/6W
R796 VRS-TV2AB102J J AA 1 kohm,1/10W
R798 VRS-TV2AB473J J AA 47 kohms,1/10W
R799 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R801 VRD-ST2CD103J J AA 10 kohm,1/6W
R802 VRS-TV2AB473J J AA 47 kohms,1/10W
R804 VRS-TV2AB104J J AA 100 kohm,1/10W
R806 VRS-TV2AB153J J AA 15 kohms,1/10W
R807 VRS-TV2AB103J J AA 10 kohm,1/10W
R808 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R809 VRS-TV2AB103J J AA 10 kohm,1/10W
R810 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R811 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R812 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R813 VRD-ST2EE100J J AA 10 ohm,1/4W
R814 VRS-TV2AB332J J AA 3.3 kohms,1/10W
R815,816 VRD-ST2CD103J J AA 10 kohm,1/6W
R817,818 VRS-TV2AB102J J AA 1 kohm,1/10W
R819 VRD-ST2CD221J J AA 220 ohms,1/6W
R820 VRS-TV2AB102J J AA 1 kohm,1/10W
R821 VRD-ST2CD220J J AA 22 ohms,1/6W
R822 VRD-ST2EE220J J AA 22 ohms,1/4W
R823 VRD-ST2CD102J J AA 1 kohm,1/6W
R824 VRS-TV2AB273J J AA 27 kohms,1/10W
R825 VRS-TV2AB104J J AA 100 kohm,1/10W
R826 VRS-TV2AB272J J AA 2.7 kohms,1/10W
R827 VRS-TV2AB273J J AA 27 kohms,1/10W
R828 VRS-TV2AB122J J AA 1.2 kohms,1/10W
R829 VRD-ST2CD683J J AA 68 kohms,1/6W
R852~855 VRS-TV2AB104J J AA 100 kohm,1/10W
R861~863 VRS-TV2AB222J J AA 2.2 kohms,1/10W
R901 VRD-ST2CD152J J AA 1.5 kohms,1/6W
R902 VRD-ST2CD563J J AA 56 kohms,1/6W
R903 VRS-TV2AB473J J AA 47 kohms,1/10W
R904 VRS-TV2AB271J J AA 270 ohms,1/10W
R905 VRS-TV2AB103J J AA 10 kohm,1/10W
R906 VRD-ST2CD152J J AA 1.5 kohms,1/6W
R907 VRD-ST2CD103J J AA 10 kohm,1/6W
R908 VRD-ST2CD473J J AA 47 kohms,1/6W
R909 ———— — Lead Jumper

R909 VRD-ST2CD102J J AA 1 kohm,1/6W

PRICE
RANK

DESCRIPTION

[Serial No.905ЧЧЧЧЧ~]
[Serial No.904ЧЧЧЧЧ Only]

OTHER CIRCUITRY PARTS

BI652/CNS652 QCNWN0126SJZZ J Connector Ass’y,2/2Pin
BI681/CNS681 QCNWN0125SJZZ J Connector Ass’y,3/3Pin
BI801/CNS801 QCNWN0120SJZZ J Connector Ass’y,8/8Pin
BI802/CNS802 QCNWN0121SJZZ J Connector Ass’y,7/7Pin
BI803/CNS803 QCNWN0122SJZZ J Connector Ass’y,6/6Pin
BI901/CNS901 QCNWN0119SJZZ J Connector Ass’y,7/7Pin
CFW701 QCNWN0124SJZZ J Flat Wire,2Pin
CFW702 QCNWN0123SJZZ J Flat Wire,2Pin
CFW901 ———— — Flat Wire,2Pin

CNP101 QCNCM931HAFZZ J AC Plug,8Pin
CNP301 QCNCM603CAFZZ J AB Plug,3Pin
CNP602 QCNCM010QAWZZ J AD Plug,15Pin
CNP603 QCNCM010QAWZZ J AD Plug,15Pin
CNP652,653 QCNCM998BAFZZ J Plug,2Pin
CNP681 QCNCM603CAFZZ J AB Plug,3Pin
CNP803 QCNCM932FAFZZ J AC Plug,6Pin
CNP901 ———— — Plug,7Pin

CNS101 QCNWN0118SJZZ J Connector Ass’y,8Pin
CNS602 QCNCW010QAWZZ J AE Socket,15Pin
CNS603 QCNCW010QAWZZ J AE Socket,15Pin
CNW601 QCNWN0127SJZZ J Flat Wire,5Pin

! F651 QFS-C252ASJNI J AH Fuse,T2.5A L 250V
! F653 QFS-C801ASJNI J AH Fuse,T800mA L 250V

J601 QJAKM0001SJZZ J AG Jack,Headphone
LCD701 RV-LX0004SJZZ J AV LCD Display
M801 RMOTV0409AFM1 J AN Motor with Gear [Sled]
M802 RMOTV0408AFM3 J AN Motor with Chassis [Spindle]
M901(237- 9) 9GD19213527 J Motor with Pulley [Tape]
PH901 ———— — Phote Interrupter

! RLY681 RRLYD0001SJZZ J AQ Relay

RX701 VHLN64H380A-1 J AK Remote Sensor,N64H380A
SO601 QTANA0003SJZZ J AG Terminal,Speaker

(Supplies at REF No.PWB-D)

(Supplies at REF No.PWB-D)

(Supplies at REF No.PWB-E)

NO.

! SO651 QSOCA0004SJZZ J AH Socket,AC Power Input

SOL901(237- 4)9GD19212118 J AP Solenoid Ass’y
SW700 QSW-Z0003AWZZ J AH Switch,Rotary Type [Jog Dial]
SW701 QSW-P0004AWZZ J AE Switch,Push Type [CD Eject]
SW702 QSW-K0005AWZZ J AC Switch,Key Type

SW703 QSW-K0005AWZZ J AC Switch,Key Type [Play]
SW704 QSW-K0005AWZZ J AC Switch,Key Type [Stop]
SW705 QSW-K0005AWZZ J AC Switch,Key Type [Function]
SW706 QSW-K0005AWZZ J AC Switch,Key Type [Band]
SW707 QSW-K0005AWZZ J AC Switch,Key Type [Memory/Set]
SW708 QSW-K0005AWZZ J AC Switch,Key Type

SW710 QSW-K0005AWZZ J AC Switch,Key Type [Fast Forward]
SW711 QSW-K0005AWZZ J AC Switch,Key Type [Rewind]
SW717 QSW-K0005AWZZ J AC Switch,Key Type [Bass/Treble]
SW718 QSW-K0005AWZZ J AC Switch,Key Type [On/Stand-by]
SW719 QSW-K0005AWZZ J AC Switch,Key Type

SW801 QSW-F9001AWZZ J AE Switch,Push Type [Pickup In]
SW901(237- 7) 9GD640101210 J AE Switch,Leaf Type [Fool Proof]
SW902(237- 8) 9GD640101210 J AE Switch,Leaf Type [CAM]

PRICE
RANK

DESCRIPTIONPARTS CODE

[Volume/Jog Dial]

[Record Pause/Beat Cancel]

[Clock/Timer/Sleep]

CD MECHANISM PARTS

301 NGERH0586AFZZ J AC Gear,Middle
302 NGERH0587AFZZ J AC Gear,Drive
303 MLEVP1054AFZZ J AC Rail,Guide
304 NSFTM0291AFFW J AD Shaft,Guide
305 PCUSG0613AFZZ J AC Cushion

! 306 DCTRH8002SJ01 J BP Pickup Unit Ass’y

306- 1 ———— — Pickup Unit
306- 2 NGERR0043AFZZ J AC Gear,Rack

306- 3 MSPRC0961AFZZ J AA Spring,Rack
307 PCOVP1333AFSA J AF Cover,Mechanism
701 XBSSD26P06000 J AA Screw,ø2.6×6mm
702 XHBSD20P05000 J AA Screw,ø2×5mm
703 XBBSD20P03000 J AA Screw,ø2×3mm
704 LX-WZ1070AFZZ J AA Washer,ø1.5×ø3.8×0.25mm
M801 RMOTV0409AFM1 J AN Motor with Gear [Sled]
M802 RMOTV0408AFM3 J AN Motor with Chassis [Spindle]
SW801 QSW-F9001AWZZ J AE Switch,Push Type [Pickup In]

(Not Replacement Item)

CABINET PARTS

201 CPNLC1028SJ01 J AV Front Panel Ass’y
201- 1 ———— — Front Panel

201- 2 HDECQ0014SJSA J AK Decoration Plate,LCD Display
201- 3 PCUSG0003SJZZ J AC Cushion,Leg
202 CDORF0002SJ01 J AQ Cassette Holder Ass’y
202- 1 ———— — Cassette Holder

202- 2 HDECQ0013SJSA J AK Decoration Plate,Cassette
203 CGERH0001SJ01 J AF Cassette Holder Damper Gear
204 MSPRD0006SJFJ J AC Spring,Cassette Holder

205 GCOVH1001SJSA J AD Cover,Remote Control Sensor
206 JKNBZ0023SJSA J AH Button,Operation,Left
207 JKNBZ0027SJSA J AM Button,Operation,Right
208 HDECQ0018SJSA J AF Ring,Jog Dial Knob
209 JKNBK0015SJSA J AF Knob,Jog Dial
210 GCABC1028SJSA J AN Top Cabinet
211 MLEVP0001SJSA J AL Lever,CD Eject Button
212 GDORT0001SJSA J AK CD Lid
213 CGERH0001SJ01 J AF CD Lid Gear Ass’y
214 JKNBZ0029SJSA J AE Button,CD Eject
215 MSPRD0007SJFJ J AD Spring,CD Lid
216 CHLDM1002SJ01 J AH Stabilizer Ass’y
216- 1 ———— — Stabilizer

216- 2 PMAGF0002AWZZ J AE Magnet,Stabilizer
217 GITAS0001SJSA J AL Side Panel,Left
218 GITAS0002SJSA J AL Side Panel,Right
219 TLABS0003SJZZ J AD Label,Class 3A
220 TLABS0004SJZZ J AC Label,Laser
221 GCABB1021SJSA J AL Rear Panel
222 QCNWN0147SJZZ J Lead Wire with Lug
223 LCHSM0004SJFW J Main Chassis

(Not Replacement Item)

(Not Replacement Item)
Holder
Ass’y

(Not Replacement Item)

– 4 –

XL-530H,CP-XL530H

PARTS CODE NO. PARTS CODE

224 LANGF0012SJFW J AF Bracket,Sub Transformer
225 LHLDW1001SJZZ J AD Nylon Band
226 PCOVW1010SJZZ J AH Cover,Power PWB

! 227 QFSHD0001AWZZ J AB Holder,Fuse

228 LANGT0001SJFW J AD Bracket,Main PWB/
229 QCNWN0148SJZZ J Lead Wire with Lug

230 PRDAR0016SJFW J Heat Sink
231 PCOVS3002SJFW J AF Shield Cover,Main PWB
232 PSHEP0002SJZZ J AH Sheet,LCD Display
233 LHLDZ1012SJSA J AG Holder,LCD Display
234 LHLDZ1013SJSA J AF Holder,LED PWB
235 TSPC-0055SJZZ J AE Label,Specifications [For U.K.]
235 TSPC-0056SJZZ J Label,Specifications [For Europe]
236 TLABN0041SJZZ J Label,SER No.
237 CMECB0002SJ01 J BL Tape Mechanism Ass’y
237- 1 94R19210703 J AE Belt,FF/REW
237- 2 9GD19210943 J AG Belt,Main
237- 3 94R192104309 J AG Pinch Roller Arm Ass’y
237- 4(SOL901)9GD19212118 J AP Solenoid Ass’y
237- 5 9GD62161401 J AN Head,Erase
237- 6 94R62010111 J Head,Record/Playback
237- 7(SW901) 9GD640101210 J AE Switch,Leaf Type [Fool Proof]
237- 8(SW902) 9GD640101210 J AE Switch,Leaf Type [CAM]
237- 9(M901) 9GD192112344 J AY Motor with Pulley [Tape]
237-10(PWB-D)9GD192121303 J AZ Tape Mechanism PWB Ass’y
237-11(PWB-E) 9GD192121304 J AW Tape Mechanism PWB Ass’y
601 XJBSF30P10000 J AA Screw,ø3×10mm
602 XEBSD25P10000 J Screw,ø2.5×10mm
603 XJBSD30P08000 J AA Screw,ø3×8mm
604 XHBSD30P06000 J AA Screw,ø3×6mm
605 XESSD30P10000 J AA Screw,ø3×10mm
606 LX-JZ0010AFFD J AA Screw,ø3×10mm
607 XEBSF25P08000 J Screw,ø2.5×8mm

PRICE
RANK

DESCRIPTIONNO.

CD Servo PWB

PRICE

RANK

DESCRIPTION

CP-XL530H

SPEAKER BOX PARTS

701 9GDHSY049SPK01 J AS Net Frame Ass’y
702 9GDHSY049SPK02 J AW Speaker Box Ass’y
703 9GDHSY049SPK03 J AG Duct Pipe
704 9GDHSY049SPK05 J AE Screw,ø4×12mm
705 9GDHSY049SPK04 J AK Cord,Speaker
706 9GDHSY049SPK09 J AC Label,Specifications
SP601,602 VSP0010PBY24N J AU Speaker,Full-Range

PACKING PARTS

1 9GDHSY049SPK07 J AD Polyethylene Bag,Speaker
2 SPAKA0018SJZZ J AK Packing Add.,Top,Speaker
3 SPAKA0018SJZZ J AK Packing Add.,Bottom,Speaker

ACCESSORIES/PACKING PARTS

! 1 QACCB0001SJ00 J AW AC Power Supply Cord
! 1 QACCE0001SJZZ J AC Power Supply Cord

2 QANTL0003SJZZ J AM FM/AM Loop Antenna
3 TCADN0001SJZZ J AE R-Card [U.K. Only]
4 RRMCG0012SJSA J AY Remote Control
4- 1 GFTAB1021AWSA J Battery Lid,Remote Control
5 SPAKA0016SJZZ J AN Packing Add.,Left/Right
6 SPAKC0044SJZZ J AT Packing Case
7 SPAKP0002SJZZ J AD Polyethylene Sheet,Unit
8 SPAKP0003SJZZ J AC Polyethylene Sheet,AC Power

9 SSAKA0002SJZZ J AE Polyethylene Bag,Accessories
10 TINSE0017SJZZ J AM Operation Manual [For U.K.]
10 TINSZ0024SJZZ J AU Operation Manual [For Europe]
11 TLABE0030SJZZ J Label,Bar Code
12 TLABM0007SJZZ J Label,Feature
13 TLABN0041SJZZ J Label,SER No.
14 TLABZ0015SJZZ J AC Label,VJ No.
15 TLABZ0034SJZZ J Label,Saving Energy
16 TLABZ0030SJZZ J Label,Ecology [For Europe Only]

[For U.K.]
[For Europe]

Supply Cord

P.W.B. ASSEMBLY (Not Replacement Item)

PWB-A1~7 DCEKK0004SJ03 J — Main/Headphones/LED/Display/

! PWB-B DCEKA0001SJ03 J — Power

PWB-C QPWBF3895AFZZ J AC CD Motor (PWB Only)
PWB-D 9GD192121303 J — Tape Mechanism
PWB-E 9GD192121304 J — Tape Mechanism

CD Servo/Switch/Washer
(Combined Ass’y)

OTHER SERVICE PART

UDSKA0004AFZZ J AZ CD Pickup Lens Cleaner Disc

– 5 –

XL-530H,CP-XL530H

XL-530H

A

307

B

701

306

306-2

304

701

C

306-1

704

306-3

302

D

702

301

303

E

703x2

M802

F

305

G

M801

305x2

SW801

H

1

23456

Figure 6 CD MECHANISM EXPLODED VIEW

– 6 –

– 49 –

PWB-C

XL-530H,CP-XL530H

XL-530H

217

A

B

C

601x2

206

205

PWB-A3

234

233

232

LCD701

231

207

601

216

216-2

PWB-A4

603

212

602x4

607

PWB-A1

216-1

601

CD
MECHANISM

602x3

606

PWB-A7

x3

220

215

213

601

211

PWB-A6

214

601

210

235

236

D

201

Q605

IC601

218

603x3

Q607

230

604x4

Silicon
Grease

PWB-B

226

PWB-A2

603

203

Q604

E

201-2

602x4

TAPE
MECHANISM

229

603

F

201-1

201-3

x2

603

204

202-1

G

202-2

209

237

(237-1,237-2,237-3,
237-4(SOL901),237-5,
237-6,237-7(SW901),
237-8(SW902),
237-9(M901),
237-10(PWB-D),
237-11(PWB-E))

208

228

604

224

227x2

PWB-A5

227x2

T681

603

T651

605

223

221

601

219

601

225

H

202

222

604

Note: Only the unit and consumale parts are supplied as aprts supply for the Tape mechanism.

1

23456

Figure 7 CABINET EXPLODED VIEW

– 7 –

– 50 –

601x2

XL-530H,CP-XL530H

704x4

703

702

706

701

705

SP601(L-CH)
SP602(R-CH)

BLACK WITH WHITE LINE

BLACK

FULL-RANGE
SPEAKER
SP601(L-CH)
SP602(R-CH)

CP-XL530H

A

B

C

D

E

F

G

H

1

23456

Figure 8 SPEAKER EXPLODED VIEW

– 8 –

– 51 –

XL-530H,CP-XL530H

PACKING OF METHOD (FOR U.K. ONLY)

XL-530H

1. AC Power Supply Cord QACCB0001SJ00

2. FM/AM Loop Antenna QANTL0003SJZZ

3. R-Card TCADN0001SJZZ

4. Remote Control RRMCG0012SJSA

5. Packing Add., Left/Right SPAKA0016SJZZ

6. Packing Case SPAKC0044SJZZ

7. Polyethylene Sheet, Unit SPAKP0002SJZZ

8. Polyethylene Sheet, SPAKP0003SJZZ
AC Power Supply Cord

9. Polyethylene Bag, Accessories SSAKA0002SJZZ

10. Operation Manual TiNSE0017SJZZ

11. Bar Code Label TLABE0030SJZZ

12. Feature Label TLABM0007SJZZ

13. SER No. Label TLABN0041SJZZ

14. VJ No. Label TLABZ0015SJZZ

15. Saving Energy Label TLABZ0034SJZZ

Setting position of switches and knobs

Tape Mechanism STOP
Cassette Holder CLOSE
CD Lid CLOSE

CP-XL530H

1. Polyethylene Bag, Speaker 9GDHSY049SPK07

2. Packing Add., Top, Speaker SPAKA0018SJZZ

3. Packing Add., Bottom, Speaker SPAKA0018SJZZ

1

8

7

2, 3, 9, 10

15

12

L

XL-530H

Left

Right

Front

R

5

4

Button
Side

1

CP-XL530H

2

Front

3

Rear

14

6

COPYRIGHT 1999 BY SHARP COPORATION

©

ALL RIGHTS RESERVED.

No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.

– 10 –

– 52 –

13

11

SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan

Printed in U.K.

A9905-2994NS•HA•C

SG • SK • E.Europe