NAMES OF PARTS .......................................................................................................................................................... 4
TEST MODE ....................................................................................................................................................................14
NOTES ON SCHEMATIC DIAGRAM ............................................................................................................................. 20
TYPE OF TRANSISTOR AND LED ................................................................................................................................ 20
SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD.............................................................................................24
WAVEFORMS OF CD CIRCUIT..................................................................................................................................... 46
FUNCTION TABLE OF IC .............................................................................................................................................. 50
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CD-C1H/CP-C1H
SAFETY PRECAUTION FOR SERVICE MANUAL
WARNINGS
THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER
COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1. THEREFORE IT IS
IMPORTANT THAT THE FOLLOWING PRECAUTIONS ARE OBSERVED DURING SERVICING TO PROTECT YOUR EYES
AGAINST EXPOSURE TO THE LASER BEAM.
1-WHEN THE CABINET IS REMOVED, THE POWER IS TURNED ON WITDOUT A COMPACT DISC IN POSITION AND THE
PICK-UP IS ON THE OUTER EDGE THE LASER WILL LIGHT FOR SEVERAL SECONDS TO DETECT A DISC. DO NOT
LOOK INTO THE PICK-UP LENS.
2-THE LASER POWER OUTPUT OF THE PICK-UP UNIT AND REPLACEMENT SERVICE PARTS ARE ALL FACTORY
PRE-SET BEFORE SHIPMENT.
DO NOT ATTEMPT TO RE-ADJUST THE LASER PICK-UP UNIT DURING REPLACEMENT OR SERVICING.
3-UNDER NO CIRCUMSTANCES STARE INTO THE PICK-UP LENS AT ANY TIME.
4-CAUTION-USE OF CONTROLS OR ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
● CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
As the laser beam used in this compact disc player
is harmful to the eyes, do not attempt to disassemble
the cabinet. Refer servicing to qualified personnel
only.
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO
BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD. STIRRA
EJ IN I STRALEN OCH BETRAKTA EJ STRALEN MED OPTISKA INSTRUMENT.
ADVERSEL-USYNLIG LASERSTRALING VED ABNING. SE IKKE IND I
STRALEN-HELLER IKKE MED OPTISKE INSTRUMENTER.
VARO! AVATTAESSA OLET ALTTIINA NAKYMATON LASERSATEILYLLE.
ALA TUIJOTA SATEESEEN ALAKA KATSO SITA OPTISEN LAITTEEN LAPI.
VARNING-OSYNLIG LASERSTRALNING NAR DENNA DEL AR OPPNAD.
STIRRA EJ IN I STRALEN OCH BETRAKTA EJ STRALEN GENOM OPTISKT
INSTRUMENT.
ADVERSEL-USYNLIG LASERSTRALING NAR DEKSEL APNES. STIRR IKKE
INN I STRALEN ELLER SE DIREKTE MED OPTISKE INSTRUMENTER.
VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN
TÄSSÄ
KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING - OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT
ÄN I DENNA BRUKSANVISNING SPECIFICERAS. KAN
ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR
LASERKLASS 1.
VARO !Avattaessa ja suojalukitus ohitettaessa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteeseen.
VARNING!Osynlig laserstralning när denna del är öppnad och spärren är urkopplad. Betrakta ej strälen.
– 2 –
CD-C1H
● General
Power source:AC 230 V, 50 Hz
Power consumption:500 W
Dimensions:Width; 270 mm (10-5/8")
Height; 356 mm (14-3/16")
Depth; 355 mm (14")
Weight:10.5 kg (23.1 lbs.)
● Amplifier section
Output power:PMPO; 880 W (total)
MPO; 440 W (220 W + 220 W)
(DIN 45 324)
RMS; 300 W (150 W + 150 W)
(DIN 45 324)
Input terminals:Video/Auxiliary (audio signal);
500 mV/47 kohms
Output terminals:Speakers; 6 ohms
Headphones; 16-50 ohms
(recommended; 32 ohms)
CD digital output (optical)
Quantization:16-bit linear
Filter:8-times oversampling digital filter
D/A converter:1-bit D/A converter
Frequency response:20 - 20,000 Hz
Dynamic range:90 dB (1 kHz)
Wow and flutter:Unmeasurable
(less than 0.001% W. peak)
● Tuner section
Frequency range:FM; 87.5 - 108 MHz
MW; 522 - 1,620 kHz
LW; 153 - 281 kHz
● Cassette deck section
Type:Compact cassette tape
Frequency response:50 - 14,000 Hz (Normal tape)
50 - 15,000 Hz (CrO
2
tape)
Motor:DC motor with electronic gov-
ernor × 1
Signal/noise ratio:55 dB (TAPE 1, playback, Dolby
NR off)
50 dB (TAPE 2, recording/playback, Dolby NR off)
Dolby NR effect; 10 dB
(at over 5 kHz)
Bias and erasure
system:AC
Tape speed:4.76 cm/sec. (1-7/8 ips.)
Wow and flutter:0.2 % (DIN 45 511, playback)
Heads:TAPE-1: Playback × 1
TAPE-2: Record/playback × 1
Erase × 1
● Speaker section
Type:3-way type [20 cm (7-7/8")
woofer, 8 cm (3-3/16") tweeter
and super tweeter]
Rated input power:150 W
Maximum input
power:300 W
Impedance:6 ohms
Dimensions:Width; 295 mm (11-5/8")
Height; 361 mm (14-1/4")
Depth; 378 mm (14-15/16")
Weight:6.7 kg (14.8 lbs.)/each
CD-C1H/CP-C1H
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
SPECIFICATIONS
CP-C1H
Specifications for this model are subject to change without
prior notice.
– 3 –
CD-C1H/CP-C1H
12
3
4567
8
9
10
15
16
17
18
19
11
12
13
14
20 21 22
23
24 25 26 27
28
29
30
31
32
33
35
37
3936
34
4038
41 42
43 44
CD-C1H
■ Front panel
11.
Disc 1 Select/Direct Play Button
12.
Disc 1 Open/Close Button
13.
Disc 2 Select/Direct Play Button
14.
Disc 2 Open/Close Button
15.
Disc 3 Select/Direct Play Button
16.
Disc 3 Open/Close Button
17.
Disc Trays
18.
Function Selector Buttons
19.
Remote Control Sensor
10.
On/Stand-by Button
11.
Programme Type/Traffic Information Search
Button
12.
EON Button
13.
ASPM Button
14.
Display Mode Selector Button
15.
Volume Control
16.
Extra Bass Button
17.
3D Surround Mode Button
18.
3D Surround Pass Button
19.
Equalizer Selector/Demo Mode Button
NAMES OF PARTS
20.
(CD) Random Play Indicator
21.
(CD/TUNER) Memory Indicator
22.
(TAPE 2) Direction Indicators
23.
(CD) Pause Indicator
24.
SRS Indicator
25.
Extra Bass Indicator
26.
Timer Play Indicator
27.
Timer Record Indicator
28.
Sleep Indicator
29.
(TAPE) Dolby NR Indicator
30.
Traffic Announcement Indicator
31.
RDS Indicator
32.
EON Indicator
33.
Programme Type Indicator
34.
Traffic Programme Indicator
35.
Traffic Information Indicator
36.
(TAPE) Reverse Mode Indicator
37.
(TAPE) Record Indicator
38.
(CD) Play Indicator
39.
(CD) Repeat Indicator
40.
(CD) Disc Number Indicators
41.
Spectrum Analyzer/Volume Level Indicator
42.
(CD) Music Schedule Indicators
43.
FM Stereo Indicator
44.
FM Stereo Mode Indicator
– 4 –
11.
(Continued)
12
910
678
3
45
11 12 13
14
1516
17
19
20
18
6
1
2
3
4
5
9
10
11
8
7
12.
13.
14.
15.
3
3
16.
17.
3
3
18.
3
19.
10.
11.
12.
13.
14.
15.
16.
17.
18.
(CD) Clear Button
Memory/Set Button
(TAPE) Reverse Mode Button
(TAPE) Reverse Play Button
(TUNER) Tuning Down Button
(CD) Track Down/Review Button
(TAPE) Fast Wind Button
Jog Dial
(TUNER) Tuning Up Button
(CD) Track Up/Cue Button
(TAPE) Fast Wind Button
(CD) Play/Repeat Button
(TAPE) Forward Play Button
(TAPE) Record Pause Button
(TAPE) Editing Speed Selector Buttons
Headphone Socket
Clock Button
Timer Button
Sleep Button
(CD) Pause Button
(CD/TAPE) Stop Button
(TAPE) Dolby NR Button
Beat Cancel Button
CD-C1H/CP-C1H
19.
(TAPE 1) Cassette Compartment
20.
(TAPE 2) Cassette Compartment
■ Rear panel
11.
Video/Auxiliary (Audio Signal) Input Sockets
12.
CD Digital Output Socket
13.
AC Power Lead
14.
FM 75 Ohms Aerial Socket
15.
MW/LW Loop Aerial Input Socket
16.
Speaker Terminals
CP-C1H
■ Speaker section
17.
Tweeter
18.
Woofer
19.
Super Tweeter
10.
Bass Reflex Duct
11.
Speaker Terminals
– 5 –
CD-C1H/CP-C1H
CD-C1H
■ Remote control
11.
Remote Control Transmitter LED
● CD control section
12.
Track Down/Review Button
13.
Track Up/Cue Button
14.
CD Select/Direct Play Buttons
15.
Play/Repeat Button
16.
Stop Button
17.
Memory Button
18.
Clear Button
19.
Random Button
10.
Pause Button
● Tuner control section
11.
Programme Type/Traffic Information Search Button
12.
Preset Up/Down Buttons
● Tape control section
13.
Reverse Play Button
14.
Record Pause Button
15.
Stop Button
16.
Forward Play Button
17.
Fast Wind Buttons
● Common section
18.
3D Surround Pass Button
19.
3D Surround Mode Button
20.
Function Selector Buttons
21.
Balance Buttons
22.
On/Stand-by Button
23.
Dimmer Button
24.
Equalizer Mode Button
25.
Extra Bass Button
26.
Volume Up/Down Buttons
2
3
13
14
20
21
22
23
7
1
89
11
18
4
5
6
10
12
15
16
17
19
24
25
26
– 6 –
OPERATION MANUAL
SETTING THE CLOCK
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Turn the jog dial to select the time display mode.
0:00AM 12:000:00AM
3
4
5
6
7
8
9
MEMORY/
SET
ON/STAND-
BY
CLOCK
"0:00" → The 24-hour dis play will appea r.
(0:00 - 23:59)
"AM 12:00" → The 12-hour display will ap pear.
(AM or PM 12:00 - 11:59)
"AM 0:00" → The 12-hour display will appear.
(AM or PM 0:00 - 11:59)
● Note that this can only be set when the unit is first installed
or it has been reset.
5
Press the MEMORY/SET button.
6
Adjust the hour by turning the jog dial.
● Turn the dial one click to advance the time by 1 hour.
Keep turning the dial to advance continuously.
● When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
Adjust the minutes by turning the jog dial.
● Turn the dial one click to advance the time by 1 minute.
Keep turning the dial to advance continuously.
● The hour setting will not advance even if minutes advance
from "59" to "00".
9
Press the MEMORY/SET button.
● The clock starts operating from "0" seconds. (Seconds are
not displayed.)
Note:
● In the event of a power failure or when the AC power lead
is disconnected, the clock display will go out.
When the AC power supply is restored, the clock display will
flash on and off to indicate the time when the power failure
occurred or when the AC power lead was disconnected.
If this happens, follow the procedure below to change the
clock time.
To change the clock time:
When the unit is in the stand-by mode:
① Press the MEMORY/SET button.
② Perform steps 6 - 9 above.
When the unit is on:
① Press the CLOCK button.
② Within 5 seconds, press the MEMORY/SET button.
③ Perform steps 6 - 9 above.
To see the time display:
Press the CLOCK button.
● The time display will appear for about 5 seconds.
To change the time display mode:
① Perform steps 1 - 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 31 of Operation Manual.
② Perform steps 1 - 9 above.
In this example, the clock is set for the 24-hour
(0:00) system.
Jog dial
2
PREPARATION FOR USE
■Remote control
Notes concerning use:
● Replace the batteries if control distance decreases or oper-
ation becomes erratic.
● Periodically clean the transmitter LED on the remote control
and the sensor on the main unit with a soft cloth.
● Exposing the sensor on the main unit to strong light may
interfere with operation. Change the lighting or the direction
of the unit.
● Keep the remote control away from moisture, excessive heat,
shock, and vibrations.
15
15
0.2 m - 6 m
(8" - 20')
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following conditions:
● To erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
● If the display is not correct.
● If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2 Press and hold down the button, the EQ/DEMO button
and the ON/STAND-BY button all at the same time. Hold
them for at least 1 second.
Caution:
● The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and CD
presets.
1,2
2
WHEN "PROTECT" APPEARS
The unit will be overheated when "PROTECT" appears in the
display.
Due to the problem in speaker circuit the unit will be switched
to the stand-by mode automatically.
In this case take the following corrective actions.
1 Unplug the AC power plug from the AC socket.
2 Make sure that the unit vent is not blocked.
3
Make sure that the speaker wires have been correctly con-
nected to the speaker terminals.
4 After checking items 2 and 3 above, wait for 2 or 3 hours
before trying to use the unit.
5 Reconnect the AC power lead.
Note:
● If "PROTECT" appears again during use, please unplug the
AC power plug, and contact the SHARP authorised service
centre.
CD-C1H/CP-C1H
– 7 –
CD-C1H/CP-C1H
DISASSEMBLY
Caution on Disassembly
Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need be
removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were
before disassembling.
4. Take suff cient care on static electricity of integrated
circuits and other circuits when servicing.
Note : After removing the connector for the optical pickup
fromthe connector wrap the conductive aluminium foil
around the front end of connector so as to protect the
optical pickup from electrostatic damage.
FIGURE
STEP
Side Panel
(Right)
(B1)x3
Ø3x10mm
(B2)x4
Ø3x10mm
Front Panel
CD Servo
PWB
(C1)x1
Main
PWB
– 8 –
CP-CH
REMOVAL
1Front Panel1. Net ....................... (A1) x1 10-2
2Speaker1. Screw ................... (B1) x2 10-3
PROCEDURE
2. Net holder ............ (A2) x4
3. Screw ................... (A3) x4
4. Screw ................... (A4) x2
2. Screw ................... (B2) x2
3. Bracket................. (B3) x1
4. Screw ................... (B4) x2
5. Screw ................... (B5) x4
FIGURE
CD-C1H
(A1)x2
Ø3x12mm
Rear Panel
Top Cabinet
Front Panel
Side Panel
(Left)
(A1)x2
Ø3x12mm
(B1)x3
Ø3x10mm
Figure 8-1
(C3)x2
Ø3x12mm
CD Changer Block
CD Changer
Holder
(C2)x2
Ø3x10mm
Rear
Panel
Figure 8-2
CD-C1H/CP-C1H
Power
PWB
(D2)x1
Ø3x10mm
Rear
Panel
(D1)x6
Ø3x10mm
(F1)x1
(E4)x1
Ø3x10mm
(E1)x1
(E5)x1
Ø3x8mm
(E2)x1
Power
AMP. PWB
Figure 9-1
(E3)x2
Pull
(E1)x2
Display PWB
(D3)x4
Ø3x10mm
Front Panel
Main PWB
(E4)x1
Ø3x10mm
(E5)x1
Ø3x8mm
Tuner
PWB
(F1)x1
Lug Wire
(F2)x1
Ø3x6mm
(F3)x2
Ø3x10mm
(M1)x1
Ø3x10mm
(M2)x4
Ø4x8mm
Power
Supply
PWB
(L3)x1
Ø3x6mm
CD Changer Block
Figure 9-3
(P1)x2
ø3x10mm
(L3)x1
Ø3x6mm
(L1)x1
(N1)x1
ø3x10mm
(L2)x4
Ø3x10mm
Power AMP.
PWB
Front Panel
(H1)x3
Ø3x10mm
(G3)x12
Ø3x10mm
Tape Mechanism
CD Switch PWB
(K1)x6
Ø3x10mm
Figure 9-2
Washer
Lug Wire
(G1)x2
(G2)x1
Display
PWB
Headphones
PWB
Open
(J1)x1
Ø3x8mm
Cassette
Holder (Left/Right)
CD Changer
Block
Tray
Switch
PWB
(R1)x1
ø2x7mm
(P1)x1
ø3x10mm
CD Digital PWB
CD Servo PWB
CD Changer Holder
Figure 9-4
CD Servo PWB
(Q1)x3
(Q2)x3
ø3 x10mm
(Q1)x3
– 9 –
Figure 9-5
CD-C1H/CP-C1H
(S1) x2
ø2 x7mm
(S3) x1
Push
.
Push the pawl of disc tray
with a proper screwdriver.
Back surface
Pawl
Pawl
Disc Tray 3
(After drawing out the disc trays 1, 2, and 3, turn
over the mechanism unit, push two pawls, and
remove successively the three disc trays from the
mechanism unit, starting with the disc tray 3.
Thereby the CD mechanism shown in the right
figure can be removed.)
Disc Tray 1
Disc Tray 2
(S7) x2
ø2 x6mm
(S4) x3
Spring
(S2) x1
(S8) x1
Normal state
Disc Tray 2
Disc Tray 3
(S5) x1
ø2.6 x12mm
Disc Tray 1
(S6) x1
(S9) x1
CD
Mechanism
(S10) x4
ø2.6 x10mm
Turn clockwise the
main cam to raise the
CD mechanism up to
the uppermost position.
Press in turns the arrow
1
parts, starting with the
2
uppermost one, to
3
withdraw the disc trays
Pawl
CP-C1H
ø4x25mm
(A2)x4
(A1)x1
ø4x20mm
(A3)x4
(A4)x2
Figure 10-1
(B3)x1
Driver
Tweeter
Super
Tweeter
(B4)x2
ø3x10mm
Front
Speaker
Front Panel
Figure 10-2Figure 10-3
Box
(B1)x2
ø3x10mm
Panel
(B5)x4
ø4x12mm
Woofer
(B2)x2
ø3x10mm
Speaker
Box
– 10 –
Tray Motor
Main Cam
Motor
Belt
(B1) x1
Belt
(B1) x1
(B2) x2
ø2.6 x4mm
(B2) x2
ø2.6 x4mm
REMOVING AND REINSTALLING THE MAIN PARTS
(When CD is in playback state.)
CD Disc
Disc Holder
Turn the main cam clockwise,
and raise the CD mechanism
and disc holder up to
uppermost position.
CD Changer
Block
Press in turns the arrow
parts, starting with the
uppermost one, to
withdraw the disc trays
CD Disc
Disc Holder
CD Mechanism
(When CD exists in the tray)
Disc Tray 1
Disc Tray 2
Disc Tray 3
Turn the main cam clockwise,
and raise the CD mechanism
and disc holder up to
uppermost position.
CD Changer
Block
1
2
3
CD MECHANISM SECTION
For the procedure to remove the CD mechanism from the
main unit, refer to Disassembling Procedure, Steps 1~8, and
13~17. (page 8).
How to Remove the optical pickup
(See Fig. 11-1.)
1. Remove the screws (A1)x 2 pcs., to remove shaft (A2)x 1
pc.
Note:
After disconnecting the optical pickup connector wrap the
front end of connector in conductive aluminum foil so as to
prevent damage to the optical pickup by static electricity.
How to Remove the tray motor/main cam motor
(See Fig. 11-2.)
1. Remove the CD changer section by the method described
in page 8, and disassemble as shown in the figure.
2. Remove the belts (B1)x 2 pcs., from the motor side.
3. Remove the screws (B2)x 4 pcs.
4. Remove the tray motor and main cam motor.
Stop Washer
(A3) x1
Pickup
CD
Mechanism
(A1) x2
ø2.6 x5mm
Figure 11-1
CD-C1H/CP-C1H
Shaft
(A2) x1
Gear
(A4) x1
How to remove the CD disc
(When CD is in playback state) (See Fig. 11-3.)
1. Remove the Top cabinet .
2. Disassemble as shown in the figure so that the CD disc of
CD changer becomes visible.
3. Remove the CD disc as shown in the figure.
How to remove the CD disc
(When CD exists in the tray) (See Fig. 11-4.)
1. Remove the Top cabinet.
2. Disassemble as shown in the figure so that the CD disc of
CD changer can be taken out.
3. Remove the CD disc from the tray as shown in the figure.
Figure 11-2
Figure 11-3
Figure 11-4
– 11 –
CD-C1H/CP-C1H
ADJUSTMENT
MECHANISM SECTION
• Driving Force Check
Torque Meter
Play: TW-2412Tape 1: Over 80 g
• Torque Check
Torque MeterSpecified Value
Tape 1
Play: TW-211130 to 60 g. cm30 to 60 g.cm
Fast forward: TW-223160 to 120 g.cm60 to 120 g.cm
Rewind: TW-223160 to 120 g.cm60 to 120 g.cm
Position of each switch or control
VolumeMAX
3D Surround Mode ButtonPASS
Pre-programmed EqualizerFLAT
Extra BassOFF
FunctionTAPE
Dolby NR switchOFF
X-BassOFF
1: Description of the "FM IF Adjustment" is not carried on this
Manual. It is because the IF coil in the FM front end section
has been best adjusted in the factory so that its further
adjustment is not needed at the field. When replacing the
FM front end assembly, no adjustment is needed either.
2: The parts in the FM front end section are prepared in a
complete unit, so you can't obtain each part individually
• FM Mute Level
Signal generator: 1 kHz, 40 kHz dev., FM modulated
• Setting the test mode
Any one of test mode can be set by pressing several keys as follows.
Hold down the EQ and CD buttons, and press the POWER switch.TEST: CD operation test
• TEST mode
Function — CD test mode
Setting of TEST mode
Indication of CD TEST mode (Fig. 14-1)
OPEN/CLOSE operation is manual operation.
The pickup can be moved by using the (
<MEMORY>
key input
When the tracking servo is activated, playback
will begin at the
Press the
STOP button.
current position.
) or () key.
IL is not performed.
The pickup
willreturn to
the STOP
position.
<MEMORY>
key input
When the tracking servo is activated, playback
will begin at the
current position.
<STOP>
key input
The pickup normally returns to
the STOP position.
<PLAY> key input
TOC. IL is performed, and the ordinary PLAY is performed.
If the following key is pressed during PLAY, it is possible
to specify directly any Track No.
<Disc Number 1> key: Track 4
<Disc Number 2> key: Track 9
<Disc Number 3> key: Track 15
Press <STOP> key.Stop
Note:
Only in STOP state it is possible to slide the pickup with the
(
) or () key.
VOL. --- Last memory
BAL. --- CENTER
R.GEQ. --- FLAT
X-BAS --- OFF
Canceling method - POWER OFF
Figure 14-1
CD SECTION
Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary
to readjust it.
Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted.
5. RF level automatic follow-up of the tracking gain
This automatic adjustment is performed each time a disc is changed.
Therefore, each disc is played back using the optimal settings.
10ms
0.50 V
IC1 16 FD
Enlarged
View
0.1s
0.50 V
IC1 16 FD
0.1s
0.50 V
IC1 7 TE
200 ms
1V/diV
IC 1 15
TO
Figure 14-2
FOCUS
OFF-SET
ADJUST
TRACKING
OFF-SET
ADJUST
1
2
TRACKING/
ERROR
BARANCE
1
ADJUST
10ms
0.50 V
IC1 7 TE
200 ms
1V/diV
IC 1 7
TE
2
Figure 14-4
TRACKING
OFF-SET
ADJUST
1
2
– 14 –
Figure 14-3
CD-C1H/CP-C1H
EXPLANATION OF AUTOMATIC SOUND VALUE CORRECTION CONTROL
1. Outline
The recent trend is toward rise of CD record level in the world, for example rock, dancing music, etc. In case of continuous high
level playback G-EQ (graphic equalizer) and VOL (Volume) are controlled (lowered) automatically after a lapse of specific time
(10 minutes) so as to get the easy-to-listen sound level.
2. Explanation of operation
The CD playback operation is explained below.
Distortion clip point
X
0w
10 minutes
A
X : Threshold value of control circuit operation
A : Hight energy (hatched area) exceeding X is detecated, and the control mode is set.
B : After a lapse of 10 minutes the control is started.
B ~ C :
Data is fetched every 4
seconds to control.
Initial frequency
characteristics.
At first, the H and L frequency characteristics are lowered as shown above so thet the distortion
and disturbance are reduced. However, if hight energy exceeding X is detected, VOL is lowered
to get sound easy to listen.
Hand L frequency characteristics are lowered.
BCD
SP output
level
VOL (Volume) is lowered.
C ~ D :
Control mode cancel conditions
Stable control
Continued control
The output data is fetched every 4 seconds to control. When quiet music is played back, the
control is performed so as to restore the initial frequency characteristics and initial VOL values.
When output exceeding X is not given
continuously for 10 minutes.
When the power is turned off or on.
– 15 –
When quiet music is played back.
When VOL is lowered.
CD-C1H/CP-C1H
RDS
RDS (Radio Data System) OPERATION
■
Receiving FM Stations with RDS (Radio Data System)
RDS is a broadcasting service which a growing number of FM stations are now providing. It allows these FM stations to
send additional signals along with their regular programme signals. For example, the stations send their station names, and
information about what type of programme they broadcast, such as sports or music, etc.
When tuned to an FM station which provide the RDS service, the RDS will appear, the station frequency (and then the
station name if sent) is displayed.
The TP (Traffic Programme) will appear on the display when the received broadcast carries traffic announcements, and the
TA (Traffic Announcement) will appear whilst a traffic announcement is being received.
EON will appear whilst the EON (Enhanced Other Networks information) data is being broadcast.
Note:
When the TP and TA appear at the same time, an announcement is being made.
When only the TA appears, an announcement is not being made. (See page 21.)
■
Information Provided by RDS
With the CD-C1H, you can watch two types of RDS service. To
show them on the display, press the DISPLAY MODE button.
Each time you press the DISPLAY MODE button, the display will
change to show the following information.
DISPLAY
PS (Programme Service):
MODE
PTY (Programme Type): Programme type will be dis-
Station Frequency:
Descriptions of the PTY (Programme Type) codes, TP (Traffic Programme) and TA (Traffic Announcement)
With the CD-C1H, you can search for and receive the following PTY, TP and TA signals.
NEWS:
AFFAIRS:
INFO:
SPORT:
EDUCATE:
DRAMA:
CULTURE:
SCIENCE:
VARIED:
DISPLAY
News
Topical programme expanding on the
current news or affairs
Programmes on medical service,
weather forecast, etc.
Sports events
Educational programmes
Radio plays
Programmes on national or regional cul-
ture.
Programmes on national sciences and
technology
Other programmes like comedies or
ceremonies
POP M:
ROCK M:
M.O.R. M:
LIGHT M:
CLASSICS:
OTHER M:
ALARM:
NONE:
TP:
TA:
Note:
● When the unit is in the EON stand-by mode and a programme is selected, the unit will display "TI" instead of
"TA".
Station names commonly
known will be displayed. "NO
PS" appears if no signal is
being sent.
played.
"NO PTY" appears if no signal
is being sent.
Station frequencies.
Pop music
Rock music
Middle-of-the-road music (usually called
"easy listening")
Light music
Classics
Other music
Emergency broadcasts
No programme type (receive only)
Broadcasts which carry traffic announcements
Traffic announcements are being broadcast at present.
Lights up when RDS station is received.
Lights up when TA station is received.
Lights up when TP station is received.
G9G9G6G8G5G4G10
G2
G3
G7
Lights up when stand-by mode and blinks during staying other network station.
Lights up when RDS with EON station is received.
8 character can display E1 table of EBU.
– 16 –
CD-C1H/CP-C1H
Yes
Displayed the TTL quantity of memo-
rized stations by ASPM operation on
this time. And return to the previous
receiving freq. automatically .
Preset CH memory become full over?
No
Begin to ASPM SCAN from the next
CH-SPAN again.
No effect
Pass
Pass
No effect
Repeat and continue with same format
ASPM operation untill 108 MHz.
After reached 108 MHz, displayed the
TTL quantity of memorized stations.
And return to the previous receiving
freq. automatically .
Effect
Memorized to the lowest
vacant preset channel.
Pass
No effect
Pass
No effect
No
No effectNoNo effect
No effect
Memorized to the lowest
vacant preset channel.
No
Yes
No operate. After displayed “END”. Return to
previous station.
Yes
No
Hold down the ASPM button for 3 more second.
ASPM, summary operation
“ASPM” blinks in the display.
Preset CH memory full over?
Begin to scan start 87.50 → 108.00 MHz
No
SD (TUNE) DET out OK?
No
Yes
If count 1st OK?
No
Yes
If count 2nd OK?
Comparing freg. same or not?
between current receiving frequency
and (already) previously memorized
frequency .
No
Yes
RDS signal or not? PI—identify
No
Yes
Comparing PI cord same or not?
between current receiving PI and
before PI which is already memorized
by ASPM on this time.
Yes
Comparing freg. same or not?
Between current receiving frequency
and (already) previously memorized
frequency .
Yes
Yes
Compare the field strength of current
receiving signal. Is receiving signal
stronger than signal which has same PI
cord and is already memorized to
preset memory ahead of this receiving
time?
– 17 –
CD-C1H/CP-C1H
• ASPM SCAN: 87.50MHz → 108.00 MHz.
• Only RDS signal is memorized by ASPM because RDS signal has PI code and is suitable and convenient for ASPM operation.
ASPM
Comparing field strength, only one strongest RDS station is memorized of all stations (repeater relay stations) that have same
PI code.
Each PI has AF’S list by individually.
Same PI code — freq: different
(AF’S)
PS: same
PTY: same
[For example]Pickup and memorized to preset CH.
f 1
f 2f 3
P 1 (PI cord)
PS 1 (Station Name)
Select signals (f1, f5, f7, f10) are memorized in the preset memory by ASPM.
• If tentative - ASPM operation is repeated intententionally, never memorized (over write) at the same frequecy.
1st time ASPM → strongest stations of each pi are memorized.
ASPM is not only very usefull for PTY search, but also EON operation.
2nd time ASPM → 2nd strong stations of each pi are memorized and so on.
PTY search function is equal to FM band search function as a result.
f 5f 4
P 2
PS 2
Exa: P1 has f1, f2, f3 (same PTY).
P2 has f4, f5 (same PTY).
---
f 6
f 7f 8
P 3
PS 3
---
f 9f 10
f 11 f 12 f13
P 4
PS 4
1. Introduction of RDS for CD-C1H
CD-C1H RDS function is equal to adding EON feature to the current CD-C75H RDS.
EON feature is EON—PTY and EON—TI.
Although PTY and TI indicators are separated, PTY contains TI in the PTY items (software) like current PTY search items.
NEWS,AFFAIRS,INFO,ALARM,TI(TTL 17 kinds)
↑
EON—PTYEON—TI
Can select and stand-byCan select and stand-by
EON—PTY and EON—TI are basically stand-by → receive the desired program of ON station.
2.The difference point from current CD-C75H RDS. (CD-C75H — CD-C1H)
1. PTY item: added TA.TTL 18 kind.
2. Each “TP”, “TA” ind. light up or go out individually.
“TA” ind. doesn’t light up on current model, CD-C75H due to none EON—TI.
3. Added 3 indicators(in FL) due to adding EON feature.
EON: Lights up only during receiving EON data (14A).
TI:During EON-TI stand-by → Light up
During receiving ON station. → blink.
PTY: During EON-PTY stanb-by → Light up
During receiving ON station. → blink.
4. No adjust type (None adjusting circuit.)
5. Added EON button.
6. Need to change RDS logo due to add EON feature.
7. Added EON—TI, EON—PTY function.
3. Summary of CD-C1H RDS—EON operation
EON—PTY:Select and set the desired “PTY” → stand-by → switch to ON(other network) Station at the
start of desired PTY automatically → stay and listen to PTY of ON station → switch back to TN(This net) station
automatically at the end of PTY(ON) i.e. after changing to another PTY(except AFFAIRS) or cancelling to receive PTY of ON
station midway.
EON—TI:Select and set the “TI” → stand-by → switch to ON station at the start of traffic announcement automati
cally → stay and listen to TA of ON station → switch back to TN station autmatically at the end of TA(ON).
ie after TA(ON) is over or cancelled to receive TA of ON station midway.
When switching TN → ON station.
In case of exist 2 more stations having the desired(specified) “PTY” or “TI”, the receiver will select and switch to ON station
comparing field strength at the same time. But when the frequency of ON station exists in the preset-memory, then reciver
switches straight to that ON station(CH), without comparing field strength so can make a quick switching from TN—ON sta
tion. Preset memory takes priority of switching TN—ON station.
therefore ASPM is usefull not only for PTY search but also for rapid EON switching. Anyway CD-C1H EON is basically standby and receiving method, along with the Guidelines for EON implementation.
↑
– 18 –
CD-C1H/CP-C1H
EON summary notice for reference
1. EON-TI/PTYEON stand-by can be set, only when EON ind. lights up.
While EON ind. goes out (NO EON STATION), EON stand-by can't be set.
If the EON button is pressed, then “NO EON” is indication the display.
2. EON-TI/PTYEven if switch back ON→ TN station continue to keep EON stand-by.
3. EON-TIDon’t switch TN→ON during TN broadcast TA. (same item)
4. EON-TI/PTY
5. EON-TI/PTYEON stand-by is perfectly cancelled (cleared) by pressing EON button 2 times during stand-by or
powerOFF or Tun Up/Down or change band or recall pre-set CH.
6. EON-TI/PTYAfter setting EON stand-by, stand-by items can be confirmed by pressing EON button one time.
7. EON-TI/PTYEON button function: •EON setting
8. EON-TI/PTYAfter setting EON-TI and EON-PTY stand-by, if when EON data is not transmitted, EON ind goes out
9. EON-TIEON-TI stand-by can't be set. When TP=0,TA=0(TN) even if EON ind. lights up and the EON button is
10. EON-PTYDon’t switch TN→ON during TN broadcast same specified PTY. (same item of PTY)
11. EON-TI/PTYSwitch TN→ON→ TN station one cycle.
12. EON-TI/PTYAfter switch TN→ON station. When ON station is NO RDS, NO signal, TA=OFF or different PTY items.
13.During receive ON station. when ON station become to be NO RDS, NO signal, TA=ON to OFF or
14. EON-TI/PTYSwitch TN→ON in case of 2 more stations exist, comparing field strength and switch to thestrongest
15.Even if switch TN→ON preset memory straight, that ON station is very weak signal, then search another
16. EON-TI/PTYNo linkage volume, power ON/OFF, and switch function.
EON can be cancelled during receiving ON station by pressing EON button if necessary and
switch back ON→TN.
•Confirm stand-by items
•Cancel (ON→TN)
•EON clear cancel (2 times)
and EON stand-by is automatically cancelled display “NO EON”.
pressed then “NO TI” is indication the display.
Never switch TN→ON1→ON2→Other net to other net station.
The receiver switch back ON→TN displaying “NO READY”.
different PTY item, The receiver switch back ON→TN.
station, if these signals are same strength, switch to the first previous station.
If same frequency as AF'Sexists in the preset memory, then switch TN→ON (preset memory station)
straight.
In case of exist 2 more preset memories of AF’S,then switch to the preset CH which taken in EON DATA
first, also in this case no concern to field strength.
AF'S (ON) station comparing field strength and switch to the strongest station as a result. Of all atations
of AF'S are very weak or no good condition, then, switch back ON→TN automatically display "NO
READY".
Traffic Programme code
(TP)
OFFOFFThis programme does not carry traffic announcements nor does
OFFONThis programmecarries EON information about another
ONOFFThis programme carries traffic announcements but none are
ONONA traffic announcement is being broadcast on this programme at
Traffic Announcement code
(TA)
Applications
it refer, via EON, to a programme that does.
programme which gives traffic information.
being broadcast at present and may also carry EON information
about other traffic announcements.
present.
– 19 –
CD-C1H/CP-C1H
NOTES ON SCHEMATIC DIAGRAM
• Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
• The indicated voltage in each section is the one measured by
Digital Multimeter between such a section and the chassis
with no signal given.
1. In the tuner section,
( ) indicates AM
< > indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.
2SC535 C
2SC1845 F
2SC2236 Y
2SC2878 B
2SC2878 A
2SD468 C
KTA1266 GR
KTA1270 Y
KTA1271 Y
KTA1273 Y
KTC3199 GR
KTC3200 GR
KTC3203 Y
KRA107 M
KRC102 M
KRC104 M
KRC107 M
• NOTES ON SCHEMATIC DIAGRAM can be found on page 20.
1
23456
Figure 44 SCHEMATIC DIAGRAM (14/15)
POWER SUPPLY PWB-C2
– 44 –
CD-C1H/CP-C1H
10
10
ION
R
PROTECTION
98
3.8V
R
0V
C997
47/50
L902
0.29µH
L901
0.29µH
(1/2W)
(1/2W)
0V
R992
10
(1/2W)
R990
10 (1/2W)
R925
56K
R926
56K
R998
R929
3.9 (1/2W)
C927
0.022(ML)
1SS133
R971
22K
C925
0.022(ML)
1SS133
RL901
RELAY
C921
0.1
(ML)
C923
0.1
(ML)
R927
4.7
(1/2W)
56K
R928
4.7
(1/2W)
C924
0.1
(ML)
C922
0.1
(ML)
KTC3199 GR
+B
D999
1SS133
+B
Q999
RELAY
DRIVER
12.1V
D912
1SS133D911
R972
22K
R973
15K
0V
0V
R996
47K
R997
3.3K
C926
0.022(ML)
C928
0.022(ML)
R930
3.9 (1/2W)
D995
1SS133
D996
1SS133
D997
SP DET
C988
10/50
ZD998
MTZJ5.1B
R931
5.6 (1/2W)
C931
0.022(ML)
C929
0.022(ML)
L911
0.29µH
L912
0.29µH
C930
0.022(ML)
C932
0.022(ML)
R932
5.6 (1/2W)
+B
R978
100K
R933
560
R934
560
R977
10K
C994
100/50
R976
47
ZD999
MTZJ5.6B
R974
3.9K
R995
18K
C998
0.001
8.8V
R975
3.9K
8.8V
0V
0V
FAN MOTOR
CONTROL
C999
0.001
C970
47/25
0V
Q995
KTC3199 GR
HP-L CH
HP-R CH
C933
0.001
(ML)
C934
0.001
(ML)
CNP901
9.3V
Q994
GND(A)
H/P SW
H/P SW
WT902
KTA1270 Y
FAN MOTOR
SO901
SPEAKER TERMINALS
+
L-CH
–
6 OHMS
–
R-CH
+
CNS901
2
2
M
1
1
M901
FAN MOTOR
CONTROL
5
5
5
4
3
2
1
1
1
FW901
HEADPHONE PWB-A3
C937
100P
L903
2.2 µH(XH)
C938
100P
J901
HEADPHONES
1
1
BI851
+B
WT853
When Servicing, pay attension as the area enclosed by this line
( ) is directry connected with AC main voltage.
F853
T2A L 250V
C860
220/50
1N4004S
C859
220/63
1N4004S
T851
POWER TRNSFORMER
T.F
F855
T2.5A L 250V
(267)
CORE
(268)
(267)
AC POWER
SUPPLY CORD
(253)
AC 230V
50Hz
RL851
D851
BR102J02
C851 0.22 (ML)
C865 0.22 (ML)
+B
+B
+B
–B
–B
L851
100µH (DH)
C866 0.22 (ML)
C852 0.22 (ML)
–B
RELAY
D870
1SS133
D850
S4VB20
+–
+B
–B
+B
–B
–38V
D852–D855
1N4004S
D852
+B
D853
R851
12K
C867
0.22 (ML)
C868
0.22 (ML)
D855
D854
C855
47/50
C857
100/35
ZD852
MTZJ100D
-37.0V
ZD854
MTZJ4.7B
VOLTAGE REGULATOR
C856
47/50
-37.6V
Q851
2SB1375
0.047
C854
0.047
(ML)
-39.8V
C853
(ML)
R857
2.2K
F858
T5A L 250V
C858
ZD853
MTZJ8.2C
ZD851
MTZJ30C
1N4004S
F857
T5A L 250V
220/50
D858
220/63
C861
D861
1N4004S
D859
D860
POWER SUPPLY PWB-C2
7
89101112
Figure 45 SCHEMATIC DIAGRAM (15/15)
– 45 –
CD-C1H/CP-C1H
0.5ms
10.0 V
JP+
0.5ms
10.0 V
JP-
0.5ms
0.50 V
JP
0.5ms
1.00 V
TE
6
7
8
9
PLAY
TCD-712 (140mm)
TN0=01
50ms
1.00 V
SPO
50ms
2.00 V
CLV+
10
11
PLAY
TCD-712
5ms
100mV
SLD
1
12
0.5ms
100mV
SLD
1
12
STOPPLAY
5ms
1
0.50 V
FE
WAVEFORMS OF CD CIRCUIT
FOCUSSERCH
5ms
2
5.0 V
DRF
0.5ms
1.00 V
3
HF
0.5ms
5.0 V
4
HFL
0.5ms
5.0 V
5
TES
0.5ms
3
1.00 V
HF
0.5ms
5.0 V
4
HFL
0.5ms
5.0 V
5
TES
50ms
10.0 V
6
JP+
50ms
7
10.0 V
JP-
50ms
8
0.50 V
JP
50ms
1.00 V
9
TE
3
1
CUE
1
2
3
REVIEW
1
2
3
CUE
10
11
20ms
1.00 V
SPO
20ms
2.00 V
CLV+
NORMAL DISC
TN0=01
PLAY
0.5ms
10.0 V
6
JP+
0.5ms
7
10.0 V
JP-
0.5ms
8
0.50 V
JP
0.5ms
9
1.00 V
TE
50ms
10.0 V
6
JP+
50ms
7
10.0 V
JP-
50ms
8
0.50 V
JP
50ms
9
1.00 V
TE
REVIEW
– 46 –
CD-C1H/CP-C1H
TROUBLESHOOTING
When the CD does not function
When the CD section does not operate When the objective lens of the optical pickup is dirty,this section may not operate.Clean
the objective lens,and check the playback operation.When this section does not operate even after the above step is taken,check
the following items.
Remove the cabinet and follow the troubleshooting instructions.
"Track skipping and/or no TOC(Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens.
Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
• The CD tray fails to operate.
Check the changer mechanism cam switch (SWB101 to
SWB104) and tray switch (SWB105 to SWB108).
Yes
Check whether state changes to Low when
IC201 pin 96 cam SW1
pin 96 cam SW2
pin 97 cam SW3
pin 98 cam SW4
is on.
Check whether state changes to Low when
IC201 pin 33 tray SWA
pin 100 tray SWB
pin 1 tray SWC
pin 2 tray SWB
is on.
Yes
ICheck whether output of pins 3 and 7 of main cam motor
driver IC81 is normal.
Yes
Check whether the output of pins 3 and 7 of tray motor
driver IC82 is normal.
Yes
Check the motors MOB1 and MOB2.
• The CD function will not work.
No
No
No
Check the connection between IC201 and SW.
Check the connection from IC2 to IC81.
Check the connection from IC2 to IC82.
The CD operating keys don't work
Yes
Check the CD, DSP, power supply, and 16.93 MHz clock
and reset terminal IC2 pin 57.
Yes
Check the waveform of SCK, SO (DATA) and SI (COMM).
Check the waveform of IC2 pin 54 (SQOUT), pin 55 (COIN),
and pin 57 (CQCK).
Yes
Check that the pickup is in the PICKUP IN switch position
of SW702A.
Yes
If the items mentioned above are OK, check the main
microcomputer IC201.
– 47 –
CD-C1H/CP-C1H
0.5s
0.50 V
IC1 16 FD
2
1
0.5s
0.50 V
IC1 7 TE
3
2
1
4
0.5s
1.00 V
IC1 16 FD
0.5s
10.0 V
IC2 13 CLV+
0.5s
10.0 V
IC1 54 DRF
0.5s
2.00 V
IC1 7 TE
• The CD operation keys work.
Check the FOCUS-HF system.
Playback can be performed without a disc.
Yes
Does the pickup move up and down two twice?
Yes
Does the output waveform of IC1 pin 16 (FD) match that
shown in Figure 48-1?
Yes
Check 4 MHz of IC1 pin 50 (CLK) line and the microcomputer
data of pin 51 (CL), pin 52 (DAT) and pin 53 (CE).
• Playback can only be performed when disc is
loaded.
Is the Focus servo active? (Can you hear it working?)
Yes
Focus search OK
No
Check the area around IC3 to CNP2.
No
No
Check the laser diode driver.
Check the area around IC1 pin 16 to pin 21 (focus servo
circuit).
Focus search is
performed two times
when play operation
is done without disc.
Figure 48-1
Does the DRF signal of IC1 pin 54 change from "L" to "H"?
Yes
Is HF waveform normal (see the Figure 48-2, Figure48-3.)?
Yes
Check the tracking system.
HF
1.0V/DIV
0.5µsec/DIV(DC)
(When playing
back the disc)
Figure 48-2
No
No
– 48 –
If the disc is not turning,
the DRF should not
change to "H".
Level is abnormal
Yes
Yes
Yes
Figure 48-3
Check the spindle system.
Check the periphery of
IC1 pin 41 and pin 42.
Check the spindle system.Waveform is unstable.
Waveform in case
of normal play-back
• Check the tracking system.
3
4
5ms
1.00 V
IC1 7 TE
5 ms
5.0 V
IC1 54 DRF
Check the waveform of IC1 pin 7 (TE).
CD-C1H/CP-C1H
The waveform shown in Figure 49-1
appears, and no disc state appears
soon.
Playback is possible in TEST mode.
Data cannot be read.
• Check the spindle system
Play operation is performed without disc.
Yes
The turntable rotates a little.
Yes
Tracking servo is inoperative.
Yes
Playback is impossible
Yes
although initialization
is possible.
Yes
Check the VCO-PLL system.
No
Yes
Normal jump is
Yes
impeded, and the
program top
cannot be
reached.
Figure 49-1
The spindle driver is normal.
Check the periphery of IC1 pin 8 to
pin 15, and IC5 to CNP2.
Check the
Yes
periphery of IC1
pin 14.
The turntable fails to rotate or rotates at high speed.
• Checking the VCO-PLL system.
Play operation is performed when disc exists.
Yes
Although the HF waveform is normal, TOC data cannot be
read.
Stop -- > Play
As VCO frequency is
0.5s
1.00 V
IC2 3 PDO
0.5s
1.00 V
IC2 16 FD
locked at 4.32 MHz,
voltage of PDD rises
and stabilizes.
2
3
Figure 49-2
• Although HF waveform is normal and time
indication is normal, no sound is not output.
No
No
Check the periphery of IC1 pin 23 to pin 27, pin 39, pin 40, IC2
pin 12, pin 13, from IC3 to CNP3.
Check the PDD waveform of IC2 pin 3. (Figure 49-2)
Abnormal
Check the IC1 pin 43, pin 44, IC2 pin 3, pin 5, pin 7, pin 10, and
pin 11.
Check the IC2 pin 48 (EFLG).
Yes
Check the IC2 pin 37 and pin 40.
Yes
Check IC501 and POWER AMP. IC901.
No
– 49 –
Usually, the number of pulses of flawless disc is 100 pulses/sec
or less.
CD-C1H/CP-C1H
FUNCTION TABLE OF IC
IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (1/2)
Pin No.Port Name
1FIN2Connection pin for photodiode of pickup.
RF signal is generated through addition with FIN pin, and FE signal is generated through subtraction.
2FIN1Connection pin for photodiode of pickup.
3EConnection pin for photodiode of pickup. TE signal is generated through subtraction with F pin.
4FConnection pin for photodiode of pickup.
5TBPin for input of DC component of TE signal.
6TE-Pin to connect gain setting resistor of TE signal to TE signal.
7TETE signal output pin.
8TESITES (Track error sense) comparator input pin. TE signal is band-passed and input.
9SCIInput pin for shock detection.
10THPin to set time constant of tracking gain.
11*TATA amplifier output pin.
12TD-Pin to compose tracking phase compensation constant between TD and VR pins.
13TDPin to set tracking phase compensation.
14JPPin to set amplitude of tracking jump signal (kick pulse).
15TOTracking control signal output pin.
16FDFocusing control signal output pin.
17FD-Pin to compose focusing phase compensation constant between FD and FA pins.
18FAPin to compose focusing phase compensation constant between FD-/FA-pins.
19FA-Pin to compose focusing phase compensation constant between FA and FE pins.
20FEOutput pin of FE signal.
21FE-Pin to connect gain setting resistor of FE signal across TE pin.
22AGNDGND for analog signal.
23SPSingle end output for CV+ and CV- pin input.
24SPISpindle amplifier input.
25SPGPin to connect gain setting resistor in the 12cm mode of spindle.
26SP-Pin to connect spindle phase compensation constant together with SPD pin.
27SPOSpindle control signal output pin.
28SLEOPin to connect thread phase compensation constant.
29SLDThread control signal output pin.
30SL-Input pin of thread feed signal from micro computer.
31SL+Input pin of thread feed signal from micro computer.
32JP-Input pin of tracking jump signal from DSP.
33JP+Input pin of tracking jump signal from DSP.
34TGLInput pin of tracking gain control signal from DSP. TGL = Gain low at "H"
35TOFFInput pin of tracking off control signal from DSP. TOFF = Off at "H"
36TES Output pin of TES signal to DSP.
37HFL(HIGH FREQUENCY LEVEL) is used to judge whether main beam is positioned on the bit or on the mirror.
38SLOFThread servo off control input pin.
39CV-Pin to input CLV error signal from DSP.
40CV+Pin to input CLV error signal from DSP.
41RFSMRF output pin.
42RFS-Pin to set gain of RF and set 3T compensation constant together with RFSM pin.
43SLC(SLICE LEVEL CONTROL) is the output pin to control of the level of the data slice with RF waveform DSP.
44SLIInput pin to control the level of data slice with DSP.
45DGNDGND pin in the digital system.
46FSCOutput pin for focus search smoothening capacitor.
47TBC(Tracking Balance Control) Pin to set EF balance variable range.
48*NCNo connect.
49DEFDefect detection output pin of disk.
50CLKReference clock input pin. 4.23MHz of DSP is input.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
Function
– 50 –
IC1 VHiLA9241M/-1: Servo Amp., (LA9241M) (2/2)
1
FIN2
FIN1
E
F
TB
TE-
TE
TESI
SCI
TH
TA
TD-
TD
JP
TO
FD
FD-
FAFE
JP+
TGL
TOFF
TES
HFL
SLOF
CV-
CV+
RFSM
RFS-
SLC
SLI
DGND
FSC
TBC
NC
DEFCLK
CL
DAT
CE
DRF
FSS
VCC2
REFI
VRLF2
PHI
BHI
LDDLDS
SLC
RF AMP
TE
F.SERVO & F.LOGICSPINDLE SERVOSLED SERVO
VCC1
2
3
4
6
7
5
8
9
10
11
12
13
14
15
16
17
1819
20
2123
22
25
26
27 28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
46
47
48
49
50
51
52
53
54
55
5657
58
59
6160
62
63
64
45
24
APC
RF DET
REF
VCA
VCA
INTER FACE
BAL
µ-COM
I/V
T.SERVO & T.LOGIC
JP-
SL+
SL-SLDSLEO
SPO
SP-SPGSPISP
AGND
FE-FA-
CD-C1H/CP-C1H
Pin No.
Port Name
Function
51CLMicro computer command clock input pin.
52DATMicro computer command data input pin.
53CEMicro computer command chip enable input pin.
54DRF(DETECT RF) RF level detection output.
55FSS(Focus Serch Select) Pin to switch focus search mode. (± search/+ search for reference voltage)
56VCC2VCC pin for servo system and digital system.
57REFIPin to connect pass control for reference voltage.
58VRReference voltage output pin.
59LF2Pin to set defect detection time constant of disk.
60PHIPin to connect capacitor for peak hold of RF signal.
61BHIPin to connect capacitor for bottom hold of RF signal.
62LDDAPC circuit output pin.
63LDSAPC circuit output pin.
64VCC1RF system VCC pin.
IC1 VHiLA9241M/-1: Servo Amp., (LA9241M)
Figure 51 BLOCK DIAGRAM OF IC
– 51 –
CD-C1H/CP-C1H
IC2 VHiLC78622K-1: Servo/Signal Control (LC78622K) (1/2)
Pin No.FunctionTerminal Name
1DEFIInputInput terminal of defect detection signal (DEF). (Connected to OV when not used.)
2TA1InputFor PLLInput terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
3PDOOutputOutput terminal of phase comparison for external VCO control.
4VVSS—Ground terminal for integrated VCO. Surely connected to 0V.
5ISETInputResistance connection terminal for current adjustment of PDO output.
6VVDD—Power terminal for integrated VCO.
7FRInputVCO frequency range adjustment.
8VSS—Ground terminal of digital system. Surely connected to 0V.
9EFMOOutputFor slice level controlEFM signal output terminal.
10EFMINInputEFM signal input terminal.
11TEST2InputInput terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
12CLV+OutoutOutput for disk motor control. 3 values can be output with the commands.
13CLV-OutputOutput for disk motor control. 3 values can be output with the commands.
14V/POutputMonitor output terminal for automatic switch of rough servo/phase control.
15HFLIntputInput terminal of track detection signal. Schmit input.
16TESInputInput terminal of tracking error signal. Schmit input.
17TOFFOutputTracking OFF output terminal.
18TGLOutputOutput terminal for switch of tracking gain "L" increases the gain.
19JP+OutputOutput for track jump control. 3 values can be output with the commands.
20JP-OutputOutput for track jump control. 3 values can be output with the commands.
21*PCKOutputClock monitor terminal for EFM data replay. 4,3218MHz as the phase clock.
22*FSEQOutputOutput terminal synchronous signal detection. "H" is output when synchronous signal detected
23VDD—Power terminal of digital system.
24CONT1OutputOPEN direction
25CONT2OutputCLOSE direction
26CONT3OutputCam motor forward rotation
27CONT4OutputCam motor reverse rotation
28CONT5OutputCam motor speed selection High speed "L" Low speed "H"
29*EMPHOutputDifference monitor terminal At "H", deemphasis disk is being replayed.
30*C2FOutputC2 flag output terminal.
31DOUTOutputOutput terminal of digital OUTPUT. (EIAJ format)
32*TEST3InputInput terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
33TEST4InputInput terminal for test. Pull-down resistor is integrated. Surely connected to 0V.
34PCCL—Terminal not use. Ground terminal.
35*MUTELOutputL channel 1 bit DACMute output terminal for L channel.
36LVDD—Power terminal for L channel.
37LCHOOutputL channel output terminal.
38LVSS—Ground terminal for L channel Surely connected to 0V.
39RVSS—R channel 1 bit DACGround terminal for R channel Surely connected to 0V.
40RCHOOutputR channel output terminal.
41RVDD—Power terminal for R channel.
42*MUTEROutputMute output terminal for R channel.
43XVDD—Power terminal for quartz oscillation.
44XOUTOutputGround terminal of 16.9344 MHz quartz oscillator.
45XINInputGround terminal of 16.9344 MHz quartz oscillator.
46XVSS—Ground terminal for quartz oscillation. Surely connected to 0V.
47*SBSYOutputOutput terminal of synchronous signal of subcode block.
48*EFLGOutputCorrection monitor terminal of C1, C2, single and double.
Input/Output
"H" for rough servo, and "L" for phase servo.
by EFM signal matches synchronous signal internally generated.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
– 52 –
CD-C1H/CP-C1H
IC2 VHiLC78622K-1: Servo/Signal Control (LC78622K) (2/2)
Pin No.
Input/Output
49*PWOutputOutput terminal of subcodes P, A, R, S, T, U and W.
50*SFSYOutputOutput terminal of synchronous signal of subcode frame. It drops when subcode stands by.
51SBCKInputClock input terminal to read subcode. Schmit input (Connected to 0V when not used.)
52*FSXOutputOutput terminal of synchronous signal of 7.35kHz divided from quartz oscillation.
53WRQOutputOutput terminal to stand by output of subcode Q.
54RWCInputInput terminal of read/write. Schmit input.
55SQOUTOutputOutput terminal of subcode Q.
56COINInputCommand input terminal from microcomputer.
57CQCKInputClock input terminal to fetch command input, or pick up subcode from SQOUT. Schmit input
58RESInputReset input terminal of LC78622. When turning on power, set it at "L".
59*TST11OutputOutput terminal for test. Used in the open state ("L" output as ordinary).
60*16MOutputOutput terminal of 16.9344Hz.
614MOutputOutput terminal of 4.2336MHz.
62TEST5InputInput terminal for test Pull-down resistor is integrated. Surely connected to 0V.
63CSInputChip selection input terminal. Pull-down resistor is integrated.
Connected to 0when not controlled.
64TEST1InputInput terminal for test Pull-down resistor is integrated. Surely connected to 0V.
Note: The same potential must be supplied to the power terminals (VDD, VVDD, LVDD, RVDD, XVDD).
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
FunctionTerminal Name
IC2 VHiLC78622K-1: Servo/Signal Control (LC78622K)
DEFI
EFMIN
FSEQ
CLV+
CLV-
V/P
PW
SBCK
SBSY
SFSY
CS
WRQ
SQOUT
CQCK
COIN
RWC
1
10
22
EFM demodulation
12
13
14
49
Subcode division
51
47
50
63
53
55
57
56
54
15
EFMO
96
Slice level
control
Sync detection
CLV
Digital servo
QCRC
µ COM
Interface
Servo commander
20
16 17
HFL
TES
JP-
TOFF
19 5818
JP+
RES
VVDDVVss
PDO
I SET
34
VCO colck oscillation
clock control
General-use port
24
25 26 27 28
TGL
CONT1
CONT2
CONT3
FR
PCK
TAI
75
24 48 60
CONT5
CONT4
59221
Flag processing of C1/C2
error detection and correction
XTAL system timing
16M
EFLG
EMPH
TSTI1
TEST1
TEST2
64
11
2KX8bit
RAM
generator
61 46
4M
XVss
TEST3
32
52
FSX
TEST4
6233
45
XIN
TEST5
43
44
XOUT
DD
XV
DD
V
23
39 41
RVss
8
DD
RV
Vss
RAM address
generator
Interpolation mute
Bilingual
Digital
attenuator
X4 oversampling
digital filter
1bitDAC
L.P.F
42
40
RCHO
MUTER
37 35
LCHO
Digital OUT
36
38
LVss
MUTEL
DD
LV
30
31
34
C2F
DOUT
PCCL
Figure 53 BLOCK DIAGRAM OF IC
– 53 –
CD-C1H/CP-C1H
IC201 RH-iX0210AWZZ: System Microcomputer (IX0210AW)(1/2)
Port NameTerminal NamePin No.Input/Output
1P06TRY_SW3InputCD Chenger mechanism tray position detection switch
2P07TRY_SW4InputCD Chenger mechanism tray position detection switch
3SO0COINOutputCD command
4SI0SQ_OUTInputCD Q code data
5SCK0CQCKOutputCD seria clock
6SO1COMOutputDISP microcomputer control line
7SI1DATInputDISP microcomputer control line
8SCK1SCKOutputDISP microcomputer control line
9P16STBOutputDISP microcomputer control line
10P17DISP_RESOutputDISP microcomputer control line
11INT0WRQInputCD WRQ input
12RESRESInputReset input
13P74DRFInputCD DRF input
14P75PU-IN SWInputCD PU-IN switch input
15VSS1VSS—Ground terminal
16CF1CF1InputMain clock 4.194304 MHz
17CF2CF2InputMain clock 4.194304 MHz
18VDD1VDD—Positive power supply
19AN0SP_63 HzInputInput for spectrum analyzer 63 Hz
20AN1SP_250 HzInputInput for spectrum analyzer 250 Hz
21AN2SP_1 kHzInputInput for spectrum analyzer 1 kHz
22AN3SP_4 kHzInputInput for spectrum analyzer 4 kHz
23AN4SP_16 KHZInputInput for spectrum analyzer 16 KHz
24AN5POSISTORInputInput for temperature detection
25AN6TUNER_SMInputFor tuner input detection
26AN7SP_DETInputFor speaker output detection
27INT1SYS_STOPInputPower failure detection input –> HOLD mode
28INT2SP PROTECTInputSpeaker ovecurrent detection input –> PROTECT mode
29INT3INT3InputFor outside break-in terminal
30PA0T2_B-FP SWInputTape B-FP switch
31PA1T2_A-FP SWInputTape A-FP switch
32PA2T2_CROM SWInputTape T2 CrO2 switch
33PA3T1_CROM SWInputTape T1 CrO2 switch
34PA4T2_RUNInputTape T2 RUN pulse
35PA5T2_PLAY SWInputtTape T2 PLAY switch
36PA6VOL SWOutputVoltage selection hold
37PA7MOTOROutputTape motor output
38PB0T2_SOLOutputFor tape T2 solenoid drive
39PB1T1_SOLOutputFor tape T1 solenoid drive
40PB2T1_RUNInputTape T1 RUN pulse
41PB3T1_PLAY SWInputTape T1 PLAY switch
42PB4HI_SPEEDOutputTape HIGH SPEED state "L" –> "H"
43PB5TA_BIASOutputTape REC BIAS OSC
44PB6BEET_CANCELOutputTape BIAS frequency selection; Usually "L"
45PB7TA_R/POutputTepe PB/REC signal selection
46PC0TA_PB-EQOutputTape playback side tape Equalizer selection NOR/CrO2
47PC1REC-EQOutputTape record Amp Equalizer selection signal NOR/CrO2
48PC2REC_MUTOutputTape record muting output
49PC3TA_T1/T2OutputTape T1 = "H" T2 = "L"
50PC4—OutputNot used
51PC5DOLBY-ON/OFFOutputDOLBY mode control ON : H OFF : L
52PC6DOLBY-PB/RECOutputDOLBY playback/record selection output RECORD : H PLAYBACK : L0
Function
– 54 –
IC201 RH-iX0210AWZZ: System Microcomputer (IX0210AW) (2/2)
CD-C1H/CP-C1H
Pin No.
53PC7PB_MUTOutputTape playback muting output
54PD0SP_RELAYOutoutFor speaker relay drive
55PD1FUN_MOTOROutputFor fan motor drive
56VDD2VDD—Positive power supply
57VSS2VSS—Ground terminal
58PD2TUNER_MUTOutputTuner muting output
59PD3SRS_PASSOutputSRS control output PASS : H Otheres : L
60PD4SRS_3D/MONOOutputSRS control output MONO : H Otheres : L
61PD5SRS_AOutputSRS control output SRS 1, 4, 5 : H Otheres : L
62PD6SRS_BOutputSRS control output SRS 2, 3, 5 : H Otheres : L
63PD7SRS_INHOutputSRS control output SRS 3, 4, 5 : H Otheres : L
64PE0Q_AOutputQ-SOUND control PASS mode : H Otheres : L
65PE1Q_BOutputQ-SOUND control Q-Sound PASS mode : H Otheres : L
66PE2SPREDOutputQ-SOUND control ENHANCDE mode : H Otheres : L
67PE3PL_ENAOutputDOLBY PROLOGIC LV1035M control
68PE4C2B_CEOutputTuner/preamplifier C2B serial control input/output control output
69PE5C2B_CLOutputTuner/preamplifier C2B serial control clock output
70PE6TUN_SDInputTuner signal detection input signal found : L
71PE7C2B_DIInputTuner /preamplifier C2B serial control data input
72PF0C2B_DOOutputTuner /preamplifier C2B serial control data output
73PF1VOICE-CANCELOutputKaraoke function. "H": ON
74PF2LINE_MUTOutputLINE out MUT signal
75PF3SYS_MUTOutputFront Amp MUT signal
76PF4REAR_MUTOutputRear Amp MUT signal
77PF5CENTER_MUTOutputCenter Amp MUT signal
78PF6SWFE_MUTOutputSuper woofer Amp MUT signal
79PF7POWEROutputSet power control, ON "H", "OFF"L"
80PL69K/10KInputSpan selection 9K "H" 10K "L"
81PL5MIC_DETInputMIC existence/nonexistence detection. Existence "L", Nonexistenece "H"
82PL4TUN_STInputGround connection by resistor
83PL0H/P SWInputH. P existence/nonexistence detection
84PL1AUT_SCANInputTuner AUT SCAN function provided/not provided
85PL2SRS_A/NAInputSURROUND SRS/Q-SOUND selection
86PL3DOL_A/NAInputDolby Pro function provided/not provided
87P30CD_MUTEOutputCD output MUT signal
88P31PCCLOutputCD general-use port control signal
89VSS3VSS—Ground terminal
90VDD3VDD—Positivo power supply
91P32RESOutputCD DSP RES signal
92P33SL-OutputCD Sled motor -signal
93P34SL+OutputCD Sled motor +signal
94P35RWCOutputCD RWC
95P00CAM_SW1InputCD Changer mechanism cam detection switch
96P01CAM_SW2InputCD Changer mechanism cam detection switch
97P02CAM_SW3InputCD Changer mechanism cam detection switch
98P03CAM_SW4InputCD Changer mechanism cam detection switch
99P04TRY_SW1InputCD Chenger mechanism tray position detection switch
100P05TRY_SW2InputCD Chenger mechanism tray position detection switch
Port Name
Terminal Name
Input/Output
Function
– 55 –
CD-C1H/CP-C1H
IC501 VHiLC75396N-1: Audio Processor (LC75396N)
Pin No.
1-3RF1C1-RF1C3 Terminal to connect capacitor of filter configuration for equalizer F1 band
Connect the capacitor between LF1C1(RF1C1) and LF1C2(RF1C2) between LF1C2 (RF1C2) and LF1C3(RF1C3).
4-6RF2C1-RF2C3 Terminal to connect capacitor of filter configuration for equalizer F2 band
Connect the capacitor between LF2C1(RF2C1) and LF2C2(RF2C2) between LF2C2 (RF2C2) and LF2C3(RF2C3).
7-9RF3C1-RF3C3 Terminal to connect capacitor of filter configuration for equalizer F3 band
Connect the capacitor between LF3C1(RF3C1) and LF3C2(RF3C2) between LF3C2 (RF3C2) and LF3C3(RF3C3).
10-12RF4C1-RF4C3 Terminal to connect capacitor of filter configuration for equalizer F4 band
Connect the capacitor between LF4C1(RF4C1) and LF4C2(RF4C2) between LF4C2 (RF4C2) and LF4C3(RF4C3).
13RF5Terminal to connect capacitor of filter configuration for equalizer F5 band
Terminal to connect the externally provided capacitor
14RTOUTEqualizer output terminal
15RFINInput terminal of R-ch front side 4dB step control
16RFCOMCommon terminal of R-ch front side 1dB step control
17RFOUTOutput terminal of R-ch front side control
18RRINInput terminal of R-ch rear side 4dB step control
19RRCOMCommon terminal of R-ch rear side 1dB step control
20RROUTOutput terminal of R-ch rear side control
21RVREFInternal analog ground terminal
22VREFConnect the capacitor of about several 10 uF between Vref and AVSS (VSS) so as to prevent power supply
ripple in the VDD/2 voltage generating section.
23CLTerminal to input serial data and clock for control
24DITerminal to input serial data and clock for control
25CEChip enable terminal. Data is written in the internal latch with a timing of changing H to L, and the specific
analog switch is actuated. Data transfer is enabled on the H level.
26VSSGND
27LVREFInternal analog ground terminal
28LROUTOutput terminal of L-ch rear side control
29LRCOMCommon terminal of L-ch rear side 1dB step control
30LRINInput terminal of L-ch rear side 4dB step control
31LFOUTOutput terminal of L-ch front side control
32LFCOMCommon terminal of L-ch front side 1dB step control
33LFINInput terminal of L-ch front side 4dB step control
34LTOUTEqualizer output terminal
35LF5Terminal to connect capacitor of filter configuration for equalizer F5 band
Terminal to connect the externally provided capacitor
36-38LF4C3-LF4C1Terminal to connect capacitor of filter configuration for equalizer F4 band
Connect the capacitor between LF4C1(RF4C1) and LF4C2(RF4C2) between LF4C2 (RF4C2) and LF4C3(RF4C3).
39-41LF3C3-LF3C1Terminal to connect capacitor of filter configuration for equalizer F3 band
Connect the capacitor between LF3C1(RF3C1) and LF3C2(RF3C2) between LF3C2 (RF3C2) and LF3C3(RF3C3).
42-44LF2C3-LF2C1Terminal to connect capacitor of filter configuration for equalizer F2 band
Connect the capacitor between LF2C1(RF2C1) and LF2C2(RF2C2) between LF2C2 (RF2C2) and LF2C3(RF2C3).
45-47LF1C3-LF1C1Terminal to connect capacitor of filter configuration for equalizer F1 band
Connect the capacitor between LF1C1(RF1C1) and LF1C2(RF1C2) between LF1C2 (RF1C2) and LF1C3(RF1C3).
48LTINEqualizer input terminal
49LSELOInput selector output terminal
50LINVIN1Operational amplifier reverse input terminal for input gain setting
51-55L5-L1Input signal terminal
56VDDPower terminal
57-61R1-R5Input signal terminal
62RINVIN1Operational amplifier reverse input terminal for input gain setting
63RSEROInput selector output terminal
64RTINEqualizer input terminal
52S20/PC4S23OutputDisplay tube segment drive
53S21/PC5S22OutputDisplay tube segment drive
54S22/PC6S21OutputDisplay tube segment drive
55S23/PC7S20OutputDisplay tube segment drive
56S24/PD0S19OutputDisplay tube segment drive
57S25/PD1S18OutputDisplay tube segment drive
58S26/PD2S17OutputDisplay tube segment drive
59S27/PD3S16OutputDisplay tube segment drive
60S28/PD4S15OutputDisplay tube segment drive
61S29/PD5S14OutputDisplay tube segment drive
62S30/PD6S13OutputDisplay tube segment drive
63S31/PD7S12OutputDisplay tube segment drive
64S32/PE0S11OutputDisplay tube segment drive
65S33/PE1S10OutputDisplay tube segment drive
66S34/PE2S9OutputDisplay tube segment drive
67S35/PE3S8OutputDisplay tube segment drive
68S36/PE4S7OutputDisplay tube segment drive
69S37/PE5S6OutputDisplay tube segment drive
70S38/PE6S5OutputDisplay tube segment drive
71S39/PE7S4OutputDisplay tube segment drive
72Vdd4Vdd-F—Normal proper supply for display tube drive
73S40/PF0S3OutputDisplay tube segment drive
74S41/PF1S2OutputDisplay tube segment drive
75S42/PF2S1OutputDisplay tube segment drive
76S43/PF3—OutputNC
77S44/PF4LED1OutputLED output H Lights : Not defined
78S45/PF5LED2OutputLED output H Lights : Not defined
79S46/PF6LED3OutputLED output H Lights : F-PLAY
80S47/PF7LED4OutputLED output H Lights : STOP
81S48/PG0LED5OutputLED output H Lights : FF
82S49/PG1LED6OutputLED output H Lights : REW
83S50/PG2LED7OutputLED output H Lights : SRS-G
84S51/PG3LED8OutputLED output H Lights : SRS-R
85P00LED9OutputLED output H Lights : VIRTUAL-G
86P01LED10OutputLED output H Lights : VIRTUAL-R
87P02LED11OutputLED output H Lights : PHANTOM-G
88P03LED12OutputLED output H Lights : PHANTOM-R
89Vss2Vss—GND
90Vdd2Vdd—Normal power supply
91P04LED13OutputLED output H Lights : NORMAL-G
92P05LED14OutputLED output H Lights : NORMAL-R
93P06LED15OutputLED output H Lights : STEREO-G
94P07LED16OutputLED output H Lights : STEREO-R
95P10/S00DIP_KETOutputSerial data output for system microcomputer
96P11/S10/SB0DIP_DATInputSerial data input for system microcomputer
97P12/SKC0DIP_SCKInputSerial clock input for system microcomputer
98P13/S01NCOutputNC
99P14/S11/SB1NCOutputNC
100P15/CK1NCOutoutNC
Port Name
Terminal Name
Input/Output
Function
– 58 –
CD-C1H/CP-C1H
VDDA
VREF
VREF
FLOUT
CIN
VSSA
VDDD
VSSD
RDS-ID
SYNC
SYR
XOUTXIN
DO
CL
DI
CE
T1
T2
REFERENCE
VOLTAGE
57kHz
BPF
(SCF)
ANTIALIASING
FILTER
CCB
TEST
SMOOTHING
FILTER
RAM
(24 BLOCK DATA)
ERROR CORRECTION
(SOFT DECISION)
PLL
(57kHz)
CLOCK
RECOVERY
(1187.5Hz)
DATA
DECODER
SYNC
DETECT-1
OSC/DIVIDER
MEMORY CONTROL
CLK(4.332MHz)
SYNC
DETECT-2
SYNC/EC CONTROLLER
156
3
4
2
20
21
22
23
7
8
1312
24
18
19
15
14
MPXIN
9
10
11
17
T3
T4
T5
T7
16
T6
ICT21 VHiLC72720/-1: RDS Microcomputer (LC72720)
Terminal NamePin No.Input/Output
1VREFOutputReference voltage output (Vdda/2)
2MPXINInputBase band (multiplex) signal input
3VDDA—Analog system power supply (+5V)
4VSSA—Analog system ground
5FLOUTOutputSub-carrier input (comparator input)
6CINInputSub-carrier output (filter output)
7T1InputTest input (to be always connected to ground)
8T2InputTest input (standby control)
0: Normal operation/1: Standby state (crystal oscillation stop)
9*T3 (RDCL)Input/Output Test I/O (RDS clock output)
10*T4 (RDDA)Input/Output Test I/O (RDS data output)
11 *T5 (RSFT)Input/Output Test I/O (Soft judgment control data output)
12XOUTOutputCrystal oscillation output
13XINInputCrystal oscillation input (external reference signal input)
14VDDD—Digital system power supply
15VSSD—Digital system ground
16*T6 (ERROR/57K/BE1)Input/Output Test I/O (Error existence/nonexistence output/playback carrier output/error block
number output)
17*T7 (CORREC/ARI-ID/BE0Input/Output Test I/O (Error existence/nonexistence output/SK detection output/error block
number output)
18*SYNCInput/Output Block sync detection output
19*RDS-IDOutputRDS detection output
20DOOutputData output
21CLInputClock inputSerial data interface (CCB)
22DIInputData input
23CEInputChip enable
24SYRInputSync and RAM address reset (positive logic)
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
If there are no indications for the electrolytic capacitors, error is ±20%.
Resistors
VRD ....................... Carbon-film type
VRS........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF ............... Cylindrical type (without lead wire)
VR • • MN............... Cylindrical type (without lead wire)
VR • • TV................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ............... Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for other parts, the resistors are ±5%
carbon-film type.
NOTE:
Parts marked with “” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
– 61 –
CD-C1H/CP-C1H
PART CODENO.PARTS CODE
PRICE
RANK
DESCRIPTIONNO.
CD-C1H
INTEGRATED CIRCUITS
IC1VHILA9241M/-1J AS Servo Amp.,LA9241M
IC2VHILC78622K-1J AY Servo/Signal Control,LC78622K
IC3VHIM56748FP-1J AR Focus/Tracking/Spin/Slide
IC81VHITA7291S/-1J AH Main Cam Motor Driver,
IC82VHITA7291S/-1J AH Tray Motor Driver, TA7291S
IC101VHIAN7345K/-1J AM Playback and Record/ Playback
IC201RH-IX0210AWZZJ AZ System Microcomputer,
IC302VHILC72131/-1J AP PLL Controller,LC72131
IC303VHILA1832//-1J AR FM IF Det./FM Mpx./ AM IF,
IC451VHISRS5250AS1J AZ SRS,SRS5250AS1
IC452VHIBU4066BC-1J AG SRS Mode Selector,BU4066BC
IC501VHILC75396N-1J AX Audio Processor,LC75396N
IC502~504VHINJM4558D-1J AH Ope Amp.,NJM4558D
IC701RH-IX0209AWZZJFL Driver & Controller,IX0209AW
IC901VHISTK41713-1J BM Power Amp.,STK41713
ICD01VHIHA12134AF1J AK Dolby NR,HA12134AF
ICD03VHIBA3311L/-1J AK REC./P.B.Equalizer Amp.,
ICP01VHINJM4565M-1J AC Low Boost Amp.,NJM4565M
ICT21VHILC72720/-1J AW RDS Microcomputer,LC72720
Driver,M56748FP
TA7291S
Amp.,AN7345K
IX0210AW
LA1832
BA3311L
TRANSISTORS
Q1VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q51VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q52VSKTC3203Y/-1J AC Silicon,NPN,KTC3203 Y
Q101,102VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q103~106VS2SC1845F/-1J AC Silicon,NPN,2SC1845 F
Q107,108VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q109VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q110,111VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q113,114VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q119VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q121,122VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q124,125VSKTA1271Y/-1J AC Silicon,PNP,KTA1271 Y
Q126,127VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q128VS2SC2236-Y-1J AB Silicon,NPN,2SC2236 Y
Q131,132VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q139~144VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q146VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q147~150VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q153,154VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q156VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q201VSKRC102M//-1J AC Digital,NPN,KRC102 M
Q202,203VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q206VSKRA107M//-1J AE Digital,PNP,KRA107 M
Q301VS2SC380-O/-1J AC Silicon,NPN,2SC380 O
Q302~304VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q353,354VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q360VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q361VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q362VSKRA107M//-1J AE Digital,PNP,KRA107 M
Q371VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q451VSKRA107M//-1J AE Digital,PNP,KRA107 M
Q452VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q458~460VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q461VSKTC3203Y/-1J AC Silicon,NPN,KTC3203 Y
Q463,464VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q465~467VS2SK246GR/-1J AB FET,2SK246 GR
Q501,502VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
Q702~714VSKTC3875GR-1J AB Silicon,NPN,KTC3875 GR
Q716~723VSKTA1504Y/-1J AB Silicon,PNP,KTA1504 Y
Q820VS2SD2012//-1J AD Silicon,NPN,2SD2012
Q821VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q822VS2SD2012//-1J AD Silicon,NPN,2SD2012
Q823VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q824VS2SD2012//-1J AD Silicon,NPN,2SD2012
Q825VS2SD468-C/-1J AD Silicon,NPN,2SD468 C
Q826VSKRA107M//-1J AE Digital,PNP,KRA107 M
Q827VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q828VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q851VS2SB1375//-1J AF Silicon,PNP,2SB1375
PRICE
RANK
Q903,904VSKTC3200GR-1J AC Silicon,NPN,KTC3200 GR
Q994VSKTA1270Y/-1J AD Silicon,PNP,KTA1270 Y
Q995VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR
Q997~999VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
QD01,02VS2SC2878A/-1J AE Silicon,NPN,2SC2878 A
QD03VSKRC107M//-1J AC Digital,NPN,KRC107 M
QD06VSKRC104M//-1J AC Digital,NPN,KRC104 M
QD07~10VSKRC107M//-1J AC Digital,NPN,KRC107 M
QM01VS2SK246GR/-1J AB FET,2SK246 GR
QM02VSKTA1273Y/-1J AE Silicon,PNP,KTA1273 Y
QM03,04VSKTA1271Y/-1J AC Silicon,PNP,KTA1271 Y
QM08VSKRC104M//-1J AC Digital,NPN,KRC104 M
QM20~22VSKRC104M//-1J AC Digital,NPN,KRC104 M
QP01,02VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
QP03,04VS2SC2878A/-1J AE Silicon,NPN,2SC2878 A
QP07,08VSKTC3199GR-1J AB Silicon,NPN,KTC3199 GR
DESCRIPTION
DIODES
D1VHD1SS133//-1J AA Silicon,1SS133
D2~4VHD1N4004S/-1J AB Silicon,1N4004S
D51VHD1SS133//-1J AA Silicon,1SS133
D81,82VHD1SS133//-1J AA Silicon,1SS133
D101~104VHD1SS133//-1J AA Silicon,1SS133
D202~205VHD1SS133//-1J AA Silicon,1SS133
D301~304VHD1SS133//-1J AA Silicon,1SS133
D351~353VHD1SS133//-1J AA Silicon,1SS133
D401~403VHD1SS133//-1J AA Silicon,1SS133
D501,502VHD1SS133//-1J AA Silicon,1SS133
D552~557VHD1SS133//-1J AA Silicon,1SS133
D701VHD1N4004S/-1J AB Silicon,1N4004S
D702VHD1SS133//-1J AA Silicon,1SS133
D823VHD1SS133//-1J AA Silicon,1SS133
D826,827VHD1SS133//-1J AA Silicon,1SS133
D829VHD1SS133//-1J AA Silicon,1SS133
! D850VHDS4VB20//-1J AG Rectifier,S4VB20
! D851VHDBR102J02-1J AM Silicon,BR102J02
D852~855VHD1N4004S/-1J AB Silicon,1N4004S
D858~861VHD1N4004S/-1J AB Silicon,1N4004S
D870VHD1SS133//-1J AA Silicon,1SS133
D901,902VHD1SS133//-1J AA Silicon,1SS133
D905,906VHD1N5402M/-1J AE Silicon,1N5402M
D907,908VHD1N4004S/-1J AB Silicon,1N4004S
D909~912VHD1SS133//-1J AA Silicon,1SS133
D993VHD1SS133//-1J AA Silicon,1SS133
D995~999VHD1SS133//-1J AA Silicon,1SS133
DD01,02VHD1SS133//-1J AA Silicon,1SS133
DM01,02VHD1SS133//-1J AA Silicon,1SS133
DM03VHD1SS133//-1J AA Silicon,1SS133
DT01,02VHD1SS133//-1J AA Silicon,1SS133
LED701~707 VHP333GTH4/-1J AC LED,Green,333GTH4
LED708VHP333GTH2/-1J AD LED,Green,333GTH2
LED709VHP333GTH4/-1J AC LED,Green,333GTH4
LED714,715VHP333GTH2/-1J AD LED,Green,333GTH2
LED716~718 VHP333GTH4/-1J AC LED,Green,333GTH4
LED721~724 VHPSPR325MV-1 J AF LED,Red,SPR325MV
LED725VHP333GTH2/-1J AD LED,Green,333GTH2
LED726VHP333GTH4/-1J AC LED,Green,333GTH4
VD301VHCKV1236Z23FJ AS Variable Capacitance,
ZD61VHEMTZJ4R7B-1 J AB Zener,4.7V,MTZJ4.7B
ZD201VHEMTZJ3R3A-1 J AB Zener,3.3V,MTZJ3.3A
ZD351VHEMTZJ4R7B-1 J AB Zener,4.7V,MTZJ4.7B
ZD352VHEMTZJ3R9B-1 J AC Zener,3.9V,MTZJ3.9B
ZD451,452VHEMTZJ8R2C-1 J AB Zener,8.2V,MTZJ8.2C
ZD550VHEMTZJ5R6A-1 J AC Zener,5.6V,MTZJ5.6A
ZD820VHEMTZJ130B-1J AC Zener,13V,MTZJ13B
ZD821VHEMTZJ5R6A-1 J AC Zener,5.6V,MTZJ5.6A
ZD822VHEMTZJ8R2C-1 J AB Zener,8.2V,MTZJ8.2C
ZD851VHEMTZJ300C-1J AC Zener,30V,MTZJ30C
ZD852VHEMTZJ4R7B-1 J AB Zener,4.7V,MTZJ4.7B
ZD853VHEMTZJ8R2C-1 J AB Zener,8.2V,MTZJ8.2C
ZD854VHEMTZJ4R7B-1 J AB Zener,4.7V,MTZJ4.7B
ZD901VHEMTZJ130B-1J AC Zener,13V,MTZJ13B
ZD903,904VHEMTZJ4R3A-1 J AC Zener,4.3V,MTZJ4.3A
ZD998VHEMTZJ5R1B-1 J AC Zener,5.1V,MTZJ5.1B
ZD999VHEMTZJ5R6B-1 J AD Zener,5.6V,MTZJ5.6B
ZDT21VHEMTZJ4R3B-1J AC Zener,4.3V,MTZJ4.3B
KV1236Z23F
FILTERS
CF301RFILF0072AFZZJ AG FM IF
– 1 –
CD-C1H/CP-C1H
NO.PART CODE
CF302RFILF0072AFZZJ AG FM IF
CF351RFILF0003AWZZJ AK FM IF
CF352RFILA0009AWZZJ AE AM IF
PRICE
RANK
DESCRIPTION
TRANSFORMERS
T301RCILA1074AFZZJ AD LW Antenna
T302RCILA1064AFZZJ AD MW Antenna
T305RCILB1073AFZZJ AC LW Oscillation
T306RCILB1074AFZZJ AC MW Oscillation
T351RCILI0011AWZZJ AD AM IF
! T851RTRNP0183AWZZ J BQ Power
COILS
L61VP-XHR82K0000J AC 0.82 µH
L95VP-XH2R2K0000J AB 2.2 µH,Choke
L102,103RCILC0094AFZZJ AD 6.8 mH
L104VP-MK331K0000J AB 330 µH,Choke
L105,106VP-XH2R2K0000J AB 2.2 µH,Choke
L201VP-DH2R2M0000J AB 2.2 µH,Choke
L251,252RCILL0105AFZZJ AE MPX. Filter
L341RBLN-0001AWZZ J AD Balun
L342VP-DH2R2K0000J AB 2.2 mmH,Peaking
L351,352VP-DH101K0000J AB 100 µH,Choke
L353VP-DH102K0000J AB 1 mH,Choke
L354RFILL0001AWZZJ AE Low Pass Filter
L701VP-CH2R2M0000J AB 2.2 µH
L851VP-DH101K0000J AB 100 µH,Choke
L901,902RCILZ0137AFZZJ AA 0.29 µH
L903VP-XH2R2K0000J AB 2.2 µH,Choke
L911,912RCILZ0137AFZZJ AA 0.29 µH
LD01,02RCILC0094AFZZJ AD 6.8 mH
LT21,22VP-XH2R2K0000J AB 2.2 µH,Choke
VARIABLE RESISTORS
VR101RVR-M0028AWZZ J AC 22 kohms (B),Semi-VR
VR102RVR-M0028AWZZ J AC 22 kohms (B),Semi-VR
VR151RVR-M0030AWZZ J AC 47 kohms (B),Semi-VR
VR152RVR-M0030AWZZ J AC 47 kohms (B),Semi-VR
VR351RVR-M0026AWZZ J AC 10 kohm (B),Semi-VR
VRD01RVR-M0028AWZZ J AC 22 kohms (B),Semi-VR
VRD02RVR-M0028AWZZ J AC 22 kohms (B),Semi-VR
VRD03RVR-M0028AWZZ J AC 22 kohms (B),Semi-VR
VRD04RVR-M0028AWZZ J AC 22 kohms (B),Semi-VR
VRM01RVR-M0030AWZZ J AC 47 kohms (B),Semi-VR
[L-CH Bias Current]
[R-CH Bias Current]
[L-CH Rec/Play Sens.]
[R-CH Rec/Play Sens.]
[FM Mute Level]
[Tape 1 Play L-CH Sens.]
[Tape 1 Play R-CH Sens.]
[Tape 2 Play L-CH Sens.]
[Tape 2 Play R-CH Sens.]
[Tape Speed]
C1RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
C2VCTYMN1CY103K J AA 0.01 µF,16V
C3RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C4RC-GZA104AF1H J AB 0.1 µF,50V,Electrolytic
C5,6VCTYPA1CX333K J AA 0.033 µF,16V
C7RC-GZA104AF1H J AB 0.1 µF,50V,Electrolytic
C8VCTYPA1CX683K J AA 0.068 µF,16V
C9VCTYPA1CX473K J AA 0.047 µF,16V
C10VCKYMN1HB181K J AA 180 pF,50V
C11,12VCTYPA1CX104K J AB 0.1 µF,16V
C13VCKYMN1HB331K J AA 330 pF,50V
C14VCTYMN1CY103K J AA 0.01 µF,16V
C16VCTYMN1CX472K J AA 0.0047 µF,16V
NO.
C17VCKYMN1HB102K J AA 0.001 µF,50V
C18RC-GZA474AF1H J AA 0.47 µF,50V,Electrolytic
C19RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C20RC-GZA476AF1AJ AB 47 µF,10V,Electrolytic
C21VCTYMN1CX332K J AA 0.0033 µF,16V
C22VCCSPA1HL221J J AA 220 pF,50V
C23VCTYMN1CX272K J AA 0.0027 µF,16V
C24VCCSMN1HL2R2C J AB 2.2 pF,50V
C25VCCSMN1HL270J J AA 27 pF,50V
C26VCTYPA1CX333K J AA 0.033 µF,16V
C27VCKYMN1HB102K J AA 0.001 µF,50V
C28VCTYPA1CX104K J AB 0.1 µF,16V
C29RC-GZA475AF1EJ AB 4.7 µF,25V,Electrolytic
C30RC-GZA104AF1H J AB 0.1 µF,50V,Electrolytic
C31VCEAZA0JW227M J AC 220 µF,6.3V,Electrolytic
C32VCTYMN1CY103K J AA 0.01 µF,16V
C33RC-GZA474AF1H J AA 0.47 µF,50V,Electrolytic
C34RC-GZA334AF1H J AA 0.33 µF,50V,Electrolytic
C35RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C36RC-GZA107AF1AJ AB 100 µF,10V,Electrolytic
C37VCTYMN1EF223Z J AA 0.022 µF,25V
C38VCTYMN1CY103K J AA 0.01 µF,16V
C39,40VCTYPA1CX473K J AA 0.047 µF,16V
C41VCCCBT1HH120J J AA 12 pF (CH),50V
C42VCCCBT1HH150J J AA 15 pF (CH),50V
C43RC-GZA107AF1AJ AB 100 µF,10V,Electrolytic
C44~49VCKYMN1HB101K J AA 100 pF,50V
C51,52RC-GZA107AF1AJ AB 100 µF,10V,Electrolytic
C53VCTYMN1EF223Z J AA 0.022 µF,25V
C54VCKYMN1HB102K J AA 0.001 µF,50V
C55RC-EZ0004AWZZ J AD 100 µF,10V,Electrolytic
C56VCTYMN1EF223Z J AA 0.022 µF,25V
C57VCKYBT1HB102K J AA 0.001 µF,50V
C71,72RC-EZ0004AWZZ J AD 100 µF,10V,Electrolytic
C80VCTYMN1EF223Z J AA 0.022 µF,25V
C81,82RC-GZA476AF1EJ AB 47 µF,25V,Electrolytic
C83VCKYMN1HB102K J AA 0.001 µF,50V
C85VCTYMN1EF223Z J AA 0.022 µF,25V
C86,87RC-GZA476AF1EJ AB 47 µF,25V,Electrolytic
C95RC-GZA107AF1AJ AB 100 µF,10V,Electrolytic
C96VCTYBT1EF223Z J AA 0.022 µF,25V
C101~104VCKYMN1HB271K J AA 270 pF,50V
C105,106VCKYMN1HB331K J AA 330 pF,50V
C107,108VCKYMN1HB561K J AA 560 pF,50V
C109VCKYPA1HF223Z J AB 0.022 µF,50V
C111~114VCKYMN1HB331K J AA 330 pF,50V
C115,116RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C117,118VCTYPA1CX333K J AA 0.033 µF,16V
C119,120VCKYMN1HB561K J AA 560 pF,50V
C121,122RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C123,124VCTYPA1CX123K J AA 0.012 µF,16V
C125,126VCTYPA1CX103K J AA 0.01 µF,16V
C127VCTYMN1EF223Z J AA 0.022 µF,25V
C128RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C131,132VCKYMN1HB271K J AA 270 pF,50V
C133,134RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C139,140VCTYMN1CX332K J AA 0.0033 µF,16V
C141,142RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C145RC-GZA226AF1E J AB 22 µF,25V,Electrolytic
C146VCEAZA1AW227M J AC 220 µF,10V,Electrolytic
C147VCTYMN1EF223Z J AA 0.022 µF,25V
C148VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C150VCQYKA2AA822J J0.0082 µF,100V,Polypropylene
C151VCQYKA1HM393J J AB 0.039 µF,50V,Mylar
C152VCEAZA1AW227M J AC 220 µF,10V,Electrolytic
C161VCKYMN1HB561K J AA 560 pF,50V
C162VCQYKA1HM473M J AB 0.047 µF,50V,Mylar
C167,168VCTYPA1CX103K J AA 0.01 µF,16V
C175,176VCTYMN1CX562K J AA 0.0056 µF,16V
C177,178VCTYMN1CX682K J AA 0.0068 µF,16V
C179,180VCTYPA1EX822K J AA 0.0082 µF,25V
C181,182RC-GZA104AF1H J AB 0.1 µF,50V,Electrolytic
C183VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C184VCEAZA1HW475M J AB 4.7 µF,50V,Electrolytic
C201VCEAZA1AW477M J470 µF,10V,Electrolytic
C202VCTYMN1CY103N J AA 0.01 µF,16V
C203RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C204VCTYMN1CY103N J AA 0.01 µF,16V
C205,206VCCCMN1HH150J J AA 15 pF (CH),50V
C207RC-GZA226AF1E J AB 22 µF,25V,Electrolytic
C251,252VCTYMN1CX332K J AA 0.0033 µF,16V
C256VCTYMN1EF223Z J AA 0.022 µF,25V
PRICE
RANK
DESCRIPTIONPARTS CODE
– 2 –
CD-C1H/CP-C1H
PART CODENO.PARTS CODE
C257RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C301VCKYMN1HB102K J AA 0.001 µF,50V
C302VCKYBT1HB102K J AA 0.001 µF,50V
C321VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C322VCCCMN1HH6R8D J AA 6.8 pF (CH),50V
C323VCTYMN1EF223Z J AA 0.022 µF,25V
C324VCCUMN1HJ270J J AA 27 pF (UJ),50V
C325VCKYMN1HB221K J AA 220 pF,50V
C326VCCCMN1HH180J J AA 18 pF (CH),50V
C327VCKYMN1HB681K J AA 680 pF,50V
C328VCTYMN1EF223Z J AA 0.022 µF,25V
C329VCCSPA1HL330J J AA 33 pF,50V
C330VCCUMN1HJ100J J AA 10 pF (UJ),50V
C331VCKYPA1HF473Z J AB 0.047 µF,50V
C332VCTYMN1EF223Z J AA 0.022 µF,25V
C333VCCCMN1HH220J J AA 22 pF (CH),50V
C334VCCUMN1HJ180J J AA 18 pF (UJ),50V
C335VCCCMN1HH180J J AA 18 pF (CH),50V
C336VCKYMN1HB471K J AA 470 pF,50V
C337VCTYMN1EF223Z J AA 0.022 µF,25V
C338VCKYMN1HB102K J AA 0.001 µF,50V
C339VCCCMN1HH220J J AA 22 pF (CH),50V
C341,342VCTYMN1EF223Z J AA 0.022 µF,25V
C343,344VCCSMN1HL330J J AA 33 pF,50V
C345~347VCTYMN1EF223Z J AA 0.022 µF,25V
C350,351VCTYMN1EF223Z J AA 0.022 µF,25V
C352RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C353,354VCTYMN1EF223Z J AA 0.022 µF,25V
C355VCCSMN1HL220J J AA 22 pF,50V
C356VCKYMN1HB102K J AA 0.001 µF,50V
C357RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C358RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C361VCTYMN1EF223Z J AA 0.022 µF,25V
C362RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C363VCTYMN1EF223Z J AA 0.022 µF,25V
C364RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C365VCTYPA1CX223K J AA 0.022 µF,16V
C366VCKYMN1HB102K J AA 0.001 µF,50V
C367,368RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C369VCCSBT1HL270J J AA 27 pF,50V
C370~372RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C373,374VCTYPA1CX333K J AA 0.033 µF,16V
C375RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic
C380RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
C381VCCCMN1HH120J J AA 12 pF (CH),50V
C382VCCCMN1HH150J J AA 15 pF (CH),50V
C384VCKYMN1HB102K J AA 0.001 µF,50V
C385VCTYMN1CY103K J AA 0.01 µF,16V
C386VCKYMN1HB331K J AA 330 pF,50V
C387VCTYMN1EF223Z J AA 0.022 µF,25V
C391RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C392VCKYMN1HB102K J AA 0.001 µF,50V
C393RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C394RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C395VCTYMN1EF223Z J AA 0.022 µF,25V
C396RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C397VCTYMN1EF223Z J AA 0.022 µF,25V
C398RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C399VCTYMN1EF223Z J AA 0.022 µF,25V
C453,454RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C456,457VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C458VCQYKA1HM473J J AB 0.047 µF,50V,Mylar
C460RC-GZA474AF1H J AA 0.47 µF,50V,Electrolytic
C461VCTYMN1CX472K J AA 0.0047 µF,16V
C471VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C472RC-GZA334AF1H J AA 0.33 µF,50V,Electrolytic
C481~484RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C485RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C486VCTYMN1EF223Z J AA 0.022 µF,25V
C487RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C488VCTYMN1EF223Z J AA 0.022 µF,25V
C501~506RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C509,510RC-GZA106AF1H J AB 10 µF,50V,Electrolytic
C511,512VCKYMN1HB101K J AA 100 pF,50V
C515,516RC-GZA474AF1H J AA 0.47 µF,50V,Electrolytic
C517,518RC-QZA184AFYJJ AC 0.18 µF,50V,Mylar
C521,522VCFYDA1HA184J J AC 0.18 µF,50V,Thin Film
C523,524VCFYDA1HA154J J AB 0.15 µF,50V,Polyester
C525,526RC-GZA224AF1H J AA 0.22 µF,50V,Electrolytic
C527,528VCQYKA1HM273J J AB 0.027 µF,50V,Mylar
C529,530VCQYKA1HM153J J AB 0.015 µF,50V,Mylar
C531,532VCQYKA1HM222J J AB 0.0022 µF,50V,Mylar
PRICE
RANK
DESCRIPTIONNO.
PRICE
RANK
C533,534VCQYKA1HM472J J AA 0.0047 µF,50V,Mylar
C535,536RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C539~542RC-GZA106AF1H J AB 10 µF,50V,Electrolytic
C543RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C545,546RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C547,548RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic
C551,552RC-GZA106AF1H J AB 10 µF,50V,Electrolytic
C555,556RC-GZA476AF1C J AB 47 µF,16V,Electrolytic
C557~559RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C560VCTYMN1EF223Z J AA 0.022 µF,25V
C561,562VCTYMN1CX682K J AA 0.0068 µF,16V
C563,564VCTYMN1CY822K J AA 0.0082 µF,16V
C565,566VCTYMN1CX272K J AA 0.0027 µF,16V
C567,568RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C569,570VCKYMN1HB681K J AA 680 pF,50V
C571,572VCKYMN1HB271K J AA 270 pF,50V
C573,574RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C575~578VCTYMN1EF223Z J AA 0.022 µF,25V
C579VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C581,582RC-GZA106AF1H J AB 10 µF,50V,Electrolytic
C701VCTYBT1EF223Z J AA 0.022 µF,25V
C702RC-GZA107AF1A J AB 100 µF,10V,Electrolytic
C705~708VCKYTV1HB102K J AA 0.001 µF,50V
C709VCCSTV1HL151J J AA 150 pF,50V
C710VCEAZA0JW227M J AC 220 µF,6.3V,Electrolytic
C711VCKYTV1HF223Z J AA 0.022 µF,50V
C715~718VCKYBT1HB151K J AA 150 pF,50V
C728~730RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
C732~741VCCSTV1HL221J J AA 220 pF,50V
C782VCEAZA1HW476M J AB 47 µF,50V,Electrolytic
C820VCTYBT1EF223Z J AA 0.022 µF,25V
C821,822RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C823VCTYMN1EF223Z J AA 0.022 µF,25V
C824RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C825VCEAZA1EW227M J220 µF,25V,Electrolytic
C826VCTYMN1EF223Z J AA 0.022 µF,25V
C827RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C830RC-GZW478AF1E J AG 4700 µF,25V,Electrolytic
C831VCTYBT1EF223Z J AA 0.022 µF,25V
C832RC-GZA226AF1E J AB 22 µF,25V,Electrolytic
C833RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C851,852RC-QZA224AFYJJ AB 0.22 µF,50V,Mylar
C853,854VCQYKA1HM473J J AB 0.047 µF,50V,Mylar
C855,856VCEAZA1HW476M J AB 47 µF,50V,Electrolytic
C857VCEAZA1VW107M J AC 100 µF,35V,Electrolytic
C858VCEAZV1HW227M J220 µF,50V,Electrolytic
C859RC-GZV227AF1JJ AD 220 µF,63V,Electrolytic
C860VCEAZV1HW227M J220 µF,50V,Electrolytic
C861RC-GZA227AF1JJ AC 220 µF,63V,Electrolytic
C865~868RC-QZA224AFYJJ AB 0.22 µF,50V,Mylar
C907,908RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
C911,912VCCSMN1HL470J J AA 47 pF,50V
C913,914VCCSMN1HL330J J AA 33 pF,50V
C917,918VCQYKA1HM223J J AB 0.022 µF,50V,Mylar
C921~924VCQYKA1HM104J J AC 0.1 µF,50V,Mylar
C925~932VCQYKA1HM223J J AB 0.022 µF,50V,Mylar
C933,934VCQYKA1HM102J J AB 0.001 µF,50V,Mylar
C935,936VCEAZA1HW476M J AB 47 µF,50V,Electrolytic
C970RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
C983,984VCEAZA1HW476M J AB 47 µF,50V,Electrolytic
C985,986VCEAZW1VW478M J4700 µF,35V,Electrolytic
C988RC-GZA106AF1H J AB 10 µF,50V,Electrolytic
C989VCEAZA1EW227M J220 µF,25V,Electrolytic
C990VCKYPA1HF223Z J AB 0.022 µF,50V
C991,992RC-GZV476AF2A J AC 47 µF,100V,Electrolytic
C994VCEAZA1HW107M J AC 100 µF,50V,Electrolytic
C995,996RC-EZ1677AFZZJ AL 3300 µF,71V,Electrolytic
C997VCEAZA1HW476M J AB 47 µF,50V,Electrolytic
C998,999VCKYPA1HB102K J AA 0.001 µF,50V
CD01,02RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
CD03,04VCKYMN1HB471K J AA 470 pF,50V
CD05VCKYMN1HB331K J AA 330 pF,50V
CD06VCKYBT1HB331K J AA 330 pF,50V
CD07,08VCKYMN1HB331K J AA 330 pF,50V
CD9~11RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
CD12,13RC-GZA224AF1H J AA 0.22 µF,50V,Electrolytic
CD14~18RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
CD19,20VCKYMN1HB151K J AA 150 pF,50V
CD21RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
CD31,32RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
CD33,34VCKYMN1HB151K J AA 150 pF,50V
CD35,36RC-GZA107AF1AJ AB 100 µF,10V,Electrolytic
DESCRIPTION
– 3 –
CD-C1H/CP-C1H
NO.PART CODE
CD37,38RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
CD39,40RC-GZA104AF1H J AB 0.1 µF,50V,Electrolytic
CD41,42RC-GZA226AF1EJ AB 22 µF,25V,Electrolytic
CD43,44VCTYMN1CY103N J AA 0.01 µF,16V
CD45RC-GZA476AF1E J AB 47 µF,25V,Electrolytic
CD46RC-GZA106AF1H J AB 10 µF,50V,Electrolytic
CD51,52RC-GZA105AF1H J AB 1 µF,50V,Electrolytic
CM01RC-GZA476AF1EJ AB 47 µF,25V,Electrolytic
CM02RC-GZA336AF1C J AB 33 µF,16V,Electrolytic
CP01,02RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic
CP07,08VCFYHA1HA124J J AB 0.12 µF,50V,Thin Film
CP09,10VCFYHA1HA334J J AC 0.33 µF,50V,Thin Film
CP11,12VCKYMN1HB102K J AA 0.001 µF,50V
CP13,14RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic
CP17VCQYKA1HM473J J AB 0.047 µF,50V,Mylar
CP18RC-GZA476AF1EJ AB 47 µF,25V,Electrolytic
CT03,04VCKYMN1HB391K J AA 390 pF,50V
CT05VCKYPA1HF223Z J AB 0.022 µF,50V
CT21RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
CT22VCTYMN1EF223Z J AA 0.022 µF,25V
CT23RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
CT24VCTYMN1EF223Z J AA 0.022 µF,25V
CT25VCKYMN1HB561K J AA 560 pF,50V
CT26,27VCCCPA1HH220J J AA 22 pF (CH),50V
CT28RC-GZA476AF1A J AB 47 µF,10V,Electrolytic
CT29VCTYMN1EF223Z J AA 0.022 µF,25V
CT36VCKYPA1HF223Z J AB 0.022 µF,50V
CT37VCTYMN1EF223Z J AA 0.022 µF,25V
CT43RC-GZA106AF1C J AB 10 µF,16V,Electrolytic
PRICE
RANK
DESCRIPTION
RESISTORS
VRD-MN2BD000C J AA 0 ohm,Jumper,ø1.4×3.5mm,Ivory
R1VRD-MN2BD100J J AA 10 ohm,1/8W
R2VRD-MN2BD683J J AA 68 kohms,1/8W
R3,4VRD-MN2BD823J J AA 82 kohms,1/8W
R5VRD-MN2BD683J J AA 68 kohms,1/8W
R6,7VRD-MN2BD823J J AA 82 kohms,1/8W
R8VRD-MN2BD153J J AA 15 kohms,1/8W
R9VRD-MN2BD104J J AA 100 kohm,1/8W
R10VRD-MN2BD222J J AA 2.2 kohms,1/8W
R11VRD-ST2CD682JJ AA 6.8 kohms,1/6W
R12VRD-MN2BD101J J AA 100 ohm,1/8W
R13VRD-MN2BD102J J AA 1 kohm,1/8W
R14VRD-MN2BD273J J AA 27 kohms,1/8W
R15VRD-MN2BD123J J AA 12 kohms,1/8W
R16VRD-MN2BD332J J AA 3.3 kohms,1/8W
R17VRD-MN2BD333J J AA 33 kohms,1/8W
R18VRD-MN2BD153J J AA 15 kohms,1/8W
R19,20VRD-ST2CD102JJ AA 1 kohm,1/6W
R21,22VRD-MN2BD223J J AA 22 kohms,1/8W
R23VRD-MN2BD103J J AA 10 kohm,1/8W
R24VRD-MN2BD473J J AA 47 kohms,1/8W
R25VRD-MN2BD152J J AA 1.5 kohms,1/8W
R26VRD-MN2BD823J J AA 82 kohms,1/8W
R27VRD-MN2BD393J J AA 39 kohms,1/8W
R28VRD-MN2BD103J J AA 10 kohm,1/8W
R29VRD-MN2BD563J J AA 56 kohms,1/8W
R30VRD-MN2BD682J J AA 6.8 kohms,1/8W
R31VRD-MN2BD122J J AA 1.2 kohms,1/8W
R32VRD-MN2BD103J J AA 10 kohm,1/8W
R33VRD-MN2BD122J J AA 1.2 kohms,1/8W
R34VRD-MN2BD223J J AA 22 kohms,1/8W
R35,36VRD-MN2BD224J J AA 220 kohms,1/8W
R37VRD-ST2CD823JJ AA 82 kohms,1/6W
R38VRD-MN2BD471J J AA 470 ohms,1/8W
R39VRD-MN2BD102J J AA 1 kohm,1/8W
R40VRD-MN2BD562J J AA 5.6 kohms,1/8W
R41,42VRD-MN2BD473J J AA 47 kohms,1/8W
R43VRD-MN2BD563J J AA 56 kohms,1/8W
R44VRD-MN2BD333J J AA 33 kohms,1/8W
R45VRD-MN2BD472J J AA 4.7 kohms,1/8W
R46VRD-MN2BD561J J AA 560 ohms,1/8W
R47VRD-MN2BD104J J AA 100 kohm,1/8W
R48VRD-MN2BD103J J AA 10 kohm,1/8W
R49VRD-ST2CD102JJ AA 1 kohm,1/6W
R50VRD-MN2BD681J J AA 680 ohms,1/8W
R51VRD-ST2CD335JJ AA 3.3 Mohms,1/6W
R52VRD-MN2BD273J J AA 27 kohms,1/8W
R53VRD-MN2BD122J J AA 1.2 kohms,1/8W
R54VRD-ST2CD331JJ AA 330 ohms,1/6W
VRS-TV2AB000JJ AA 0 ohm,Jumper,1.25×2mm,Green
NO.
R55VRD-MN2BD151J J AA 150 ohms,1/8W
R56,57VRD-MN2BD102J J AA 1 kohm,1/8W
R58,59VRD-ST2CD102JJ AA 1 kohm,1/6W
R60~62VRD-MN2BD102J J AA 1 kohm,1/8W
R63VRD-ST2CD102JJ AA 1 kohm,1/6W
R64VRD-MN2BD220J J AA 22 ohms,1/8W
R66VRD-MN2BD331J J AA 330 ohms,1/8W
R71,72VRD-MN2BD272J J AA 2.7 kohms,1/8W
R73,74VRD-MN2BD681J J AA 680 ohms,1/8W
R80VRD-MN2BD392J J AA 3.9 kohms,1/8W
R81VRD-MN2BD272J J AA 2.7 kohms,1/8W
R82VRD-MN2BD105J J AA 1 Mohm,1/8W
R83,84VRD-ST2EE1R0JJ AA 1 ohm,1/4W
R85VRD-MN2BD272J J AA 2.7 kohms,1/8W
R86VRD-MN2BD822J J AA 8.2 kohms,1/8W
R87VRD-MN2BD332J J AA 3.3 kohms,1/8W
R88~92VRD-ST2CD102JJ AA 1 kohm,1/6W
R101,102VRD-ST2CD102JJ AA 1 kohm,1/6W
R103,104VRD-MN2BD222J J AA 2.2 kohms,1/8W
R105,106VRD-MN2BD332J J AA 3.3 kohms,1/8W
R107,108VRD-MN2BD104J J AA 100 kohm,1/8W
R109VRD-ST2CD103JJ AA 10 kohm,1/6W
R110VRD-MN2BD103J J AA 10 kohm,1/8W
R111,112VRD-ST2CD153JJ AA 15 kohms,1/6W
R113VRD-MN2BD103J J AA 10 kohm,1/8W
R114,115VRD-ST2CD103JJ AA 10 kohm,1/6W
R117,118VRD-ST2CD102JJ AA 1 kohm,1/6W
R119,120VRD-ST2CD560JJ AA 56 ohms,1/6W
R121,122VRD-MN2BD104J J AA 100 kohm,1/8W
R123,124VRD-MN2BD392J J AA 3.9 kohms,1/8W
R125VRD-ST2CD562JJ AA 5.6 kohms,1/6W
R126~128VRD-MN2BD562J J AA 5.6 kohms,1/8W
R129,130VRD-MN2BD682J J AA 6.8 kohms,1/8W
R131,132VRD-MN2BD224J J AA 220 kohms,1/8W
R133VRD-ST2CD223JJ AA 22 kohms,1/6W
R134VRD-MN2BD683J J AA 68 kohms,1/8W
R135,136VRD-ST2CD332JJ AA 3.3 kohms,1/6W
R137,138VRD-ST2CD682JJ AA 6.8 kohms,1/6W
R139,140VRD-MN2BD101J J AA 100 ohm,1/8W
R141VRD-ST2CD1R0J J AA 1 ohm,1/6W
R145VRD-MN2BD103J J AA 10 kohm,1/8W
R148VRD-ST2EE221JJ AA 220 ohms,1/4W
R149~152VRD-MN2BD103J J AA 10 kohm,1/8W
R153VRD-ST2CD103JJ AA 10 kohm,1/6W
R154VRD-MN2BD103J J AA 10 kohm,1/8W
R155,156VRD-MN2BD153J J AA 15 kohms,1/8W
R157VRD-MN2BD472J J AA 4.7 kohms,1/8W
R158VRD-ST2EE221JJ AA 220 ohms,1/4W
R160,161VRD-ST2CD151JJ AA 150 ohms,1/6W
R162,163VRD-ST2CD104JJ AA 100 kohm,1/6W
R164,165VRD-MN2BD472J J AA 4.7 kohms,1/8W
R166VRD-ST2CD223JJ AA 22 kohms,1/6W
R167VRD-MN2BD473J J AA 47 kohms,1/8W
R168VRD-MN2BD4R7J J A A 4.7 ohms,1/8W
R169VRD-MN2BD103J J AA 10 kohm,1/8W
R170VRD-ST2CD472JJ AA 4.7 kohms,1/6W
R171VRD-ST2CD332JJ AA 3.3 kohms,1/6W
R172VRD-MN2BD102J J AA 1 kohm,1/8W
R173,174VRD-MN2BD223J J AA 22 kohms,1/8W
R179,180VRD-MN2BD392J J AA 3.9 kohms,1/8W
R185,186VRD-ST2EE330JJ AA 33 ohms,1/4W
R189VRD-ST2CD100JJ AA 10 ohm,1/6W
R190VRD-MN2BD100J J AA 10 ohm,1/8W
R191,192VRD-MN2BD152J J AA 1.5 kohms,1/8W
R195,196VRD-MN2BD102J J AA 1 kohm,1/8W
R197,198VRD-MN2BD101J J AA 100 ohm,1/8W
R201,202VRD-ST2CD103JJ AA 10 kohm,1/6W
R204~206VRD-MN2BD103J J AA 10 kohm,1/8W
R207,208VRD-ST2CD103JJ AA 10 kohm,1/6W
R210VRD-ST2CD473JJ AA 47 kohms,1/6W
R211VRD-ST2CD103JJ AA 10 kohm,1/6W
R214VRD-ST2CD473JJ AA 47 kohms,1/6W
R215~217VRD-MN2BD103J J AA 10 kohm,1/8W
R218VRD-MN2BD473J J AA 47 kohms,1/8W
R219VRD-ST2CD103JJ AA 10 kohm,1/6W
R220VRD-ST2CD473JJ AA 47 kohms,1/6W
R221VRD-ST2CD103JJ AA 10 kohm,1/6W
R222VRD-MN2BD103J J AA 10 kohm,1/8W
R223~228VRD-ST2CD103JJ AA 10 kohm,1/6W
R229,230VRD-MN2BD151J J AA 150 ohms,1/8W
R231VRD-MN2BD102J J AA 1 kohm,1/8W
R232VRD-MN2BD101J J AA 100 ohm,1/8W
PRICE
RANK
DESCRIPTIONPARTS CODE
– 4 –
CD-C1H/CP-C1H
PART CODENO.PARTS CODE
R233,234VRD-MN2BD103J J AA 10 kohm,1/8W
R235VRD-MN2BD102J J AA 1 kohm,1/8W
R236VRD-MN2BD332J J AA 3.3 kohms,1/8W
R237VRD-MN2BD102J J AA 1 kohm,1/8W
R238VRD-ST2CD104JJ AA 100 kohm,1/6W
R239VRD-MN2BD820J J AA 82 ohms,1/8W
R240VRD-MN2BD103J J AA 10 kohm,1/8W
R256VRD-MN2BD102J J AA 1 kohm,1/8W
R257VRD-MN2BD103J J AA 10 kohm,1/8W
R258VRD-MN2BD103J J AA 10 kohm,1/8W
R301VRD-MN2BD331J J AA 330 ohms,1/8W
R319VRD-MN2BD104J J AA 100 kohm,1/8W
R323VRD-MN2BD683J J AA 68 kohms,1/8W
R324VRD-MN2BD104J J AA 100 kohm,1/8W
R331VRD-MN2BD562J J AA 5.6 kohms,1/8W
R332VRD-MN2BD104J J AA 100 kohm,1/8W
R333VRD-MN2BD562J J AA 5.6 kohms,1/8W
R334VRD-ST2CD562JJ AA 5.6 kohms,1/6W
R335VRD-MN2BD104J J AA 100 kohm,1/8W
R336VRD-ST2CD472JJ AA 4.7 kohms,1/6W
R337VRD-ST2CD471JJ AA 470 ohms,1/6W
R344VRD-MN2BD471J J AA 470 ohms,1/8W
R345VRD-MN2BD472J J AA 4.7 kohms,1/8W
R346VRD-MN2BD331J J AA 330 ohms,1/8W
R347VRD-MN2BD682J J AA 6.8 kohms,1/8W
R348VRD-MN2BD681J J AA 680 ohms,1/8W
R349VRD-ST2CD330JJ AA 33 ohms,1/6W
R350VRD-ST2CD272JJ AA 2.7 kohms,1/6W
R351VRD-MN2BD562J J AA 5.6 kohms,1/8W
R352VRD-MN2BD102J J AA 1 kohm,1/8W
R353VRD-MN2BD271J J AA 270 ohms,1/8W
R354VRD-ST2CD472JJ AA 4.7 kohms,1/6W
R355VRD-MN2BD332J J AA 3.3 kohms,1/8W
R356VRD-MN2BD102J J AA 1 kohm,1/8W
R357VRD-ST2CD474JJ AA 470 kohms,1/6W
R358VRD-MN2BD822J J AA 8.2 kohms,1/8W
R359VRD-MN2BD182J J AA 1.8 kohms,1/8W
R360VRD-MN2BD472J J AA 4.7 kohms,1/8W
R361,362VRD-MN2BD471J J AA 470 ohms,1/8W
R363,364VRD-MN2BD222J J AA 2.2 kohms,1/8W
R365,366VRD-MN2BD103J J AA 10 kohm,1/8W
R367VRD-MN2BD102J J AA 1 kohm,1/8W
R368VRD-ST2CD333JJ AA 33 kohms,1/6W
R369VRD-MN2BD820J J AA 82 ohms,1/8W
R370VRD-MN2BD102J J AA 1 kohm,1/8W
R371~374VRD-MN2BD102J J AA 1 kohm,1/8W
R376VRD-MN2BD102J J AA 1 kohm,1/8W
R377VRD-ST2CD473JJ AA 47 kohms,1/6W
R378VRD-MN2BD823J J AA 82 kohms,1/8W
R379VRD-MN2BD222J J AA 2.2 kohms,1/8W
R380VRD-MN2BD152J J AA 1.5 kohms,1/8W
R381VRD-MN2BD103J J AA 10 kohm,1/8W
R382VRD-ST2EE151JJ AA 150 ohms,1/4W
R383~385VRD-MN2BD562J J AA 5.6 kohms,1/8W
R387VRD-MN2BD223J J AA 22 kohms,1/8W
R391,392VRD-ST2EE391JJ AA 390 ohms,1/4W
R393VRD-ST2CD102JJ AA 1 kohm,1/6W
R395VRD-ST2CD473JJ AA 47 kohms,1/6W
R397VRD-MN2BD102J J AA 1 kohm,1/8W
R455,456VRD-MN2BD104J J AA 100 kohm,1/8W
R459VRD-MN2BD104J J AA 100 kohm,1/8W
R460VRD-ST2CD104JJ AA 100 kohm,1/6W
R461,462VRD-MN2BD104J J AA 100 kohm,1/8W
R465VRD-ST2CD102JJ AA 1 kohm,1/6W
R466VRD-MN2BD102J J AA 1 kohm,1/8W
R467VRD-ST2CD681JJ AA 680 ohms,1/6W
R468,469VRD-MN2BD102J J AA 1 kohm,1/8W
R470VRD-ST2CD103JJ AA 10 kohm,1/6W
R471,472VRD-MN2BD104J J AA 100 kohm,1/8W
R473,474VRD-MN2BD103J J AA 10 kohm,1/8W
R475VRD-MN2BD222J J AA 2.2 kohms,1/8W
R477VRD-ST2CD681JJ AA 680 ohms,1/6W
R479VRD-MN2BD223J J AA 22 kohms,1/8W
R480VRD-MN2BD473J J AA 47 kohms,1/8W
R481VRD-MN2BD392J J AA 3.9 kohms,1/8W
R482VRD-ST2CD333JJ AA 33 kohms,1/6W
R483VRD-MN2BD104J J AA 100 kohm,1/8W
R484VRD-MN2BD152J J AA 1.5 kohms,1/8W
R487VRD-MN2BD104J J AA 100 kohm,1/8W
R488VRD-MN2BD472J J AA 4.7 kohms,1/8W
R490VRD-MN2BD472J J AA 4.7 kohms,1/8W
R491VRD-MN2BD152J J AA 1.5 kohms,1/8W
PRICE
RANK
DESCRIPTIONNO.
PRICE
RANK
R492VRD-MN2BD472J J AA 4.7 kohms,1/8W
R493VRD-MN2BD102J J AA 1 kohm,1/8W
R498VRD-MN2BD472J J AA 4.7 kohms,1/8W
R501,502VRD-MN2BD564J J AA 560 kohms,1/8W
R503,504VRD-MN2BD153J J AA 15 kohms,1/8W
R505,506VRD-MN2BD332J J AA 3.3 kohms,1/8W
R509~511VRD-ST2CD102JJ AA 1 kohm,1/6W
R513,514VRD-MN2BD102J J AA 1 kohm,1/8W
R517,518VRD-ST2CD102JJ AA 1 kohm,1/6W
R521,522VRD-ST2CD102JJ AA 1 kohm,1/6W
R553VRD-ST2CD153JJ AA 15 kohms,1/6W
R554VRD-MN2BD474J J AA 470 kohms,1/8W
R555VRD-MN2BD274J J AA 270 kohms,1/8W
R556VRD-ST2CD563JJ AA 56 kohms,1/6W
R557VRD-MN2BD474J J AA 470 kohms,1/8W
R558VRD-ST2CD104JJ AA 100 kohm,1/6W
R559VRD-ST2CD225JJ AA 2.2 Mohms,1/6W
R560VRD-MN2BD225J J AA 2.2 Mohms,1/8W
R561VRD-MN2BD104J J AA 100 kohm,1/8W
R562VRD-MN2BD183J J AA 18 kohms,1/8W
R563VRD-MN2BD223J J AA 22 kohms,1/8W
R564VRD-MN2BD684J J AA 680 kohms,1/8W
R565VRD-ST2CD224JJ AA 220 kohms,1/6W
R566VRD-MN2BD104J J AA 100 kohm,1/8W
R567VRD-ST2CD123JJ AA 12 kohms,1/6W
R568VRD-ST2CD683JJ AA 68 kohms,1/6W
R569VRD-MN2BD394J J AA 390 kohms,1/8W
R570VRD-MN2BD224J J AA 220 kohms,1/8W
R571VRD-MN2BD104J J AA 100 kohm,1/8W
R572VRD-MN2BD474J J AA 470 kohms,1/8W
R573VRD-MN2BD123J J AA 12 kohms,1/8W
R574VRD-MN2BD393J J AA 39 kohms,1/8W
R575VRD-ST2CD224JJ AA 220 kohms,1/6W
R576VRD-MN2BD104J J AA 100 kohm,1/8W
R577VRD-MN2BD394J J AA 390 kohms,1/8W
R578VRD-ST2CD103JJ AA 10 kohm,1/6W
R579VRD-MN2BD333J J AA 33 kohms,1/8W
R580VRD-ST2CD224JJ AA 220 kohms,1/6W
R581VRD-MN2BD104J J AA 100 kohm,1/8W
R582VRD-ST2EE331JJ AA 330 ohms,1/4W
R583VRD-ST2CD221JJ AA 220 ohms,1/6W
R591,592VRD-ST2CD272JJ AA 2.7 kohms,1/6W
R595,596VRD-ST2CD222JJ AA 2.2 kohms,1/6W
R700VRD-ST2EE390JJ AA 39 ohms,1/4W
R701~703VRS-TV2AB103JJ AA 10 kohm,1/10W
R706,707VRS-TV2AB102JJ AA 1 kohm,1/10W
R708VRD-ST2CD821JJ AA 820 ohms,1/6W
R709~712VRS-TV2AB102JJ AA 1 kohm,1/10W
R713VRD-ST2CD102JJ AA 1 kohm,1/6W
R714,715VRS-TV2AB102JJ AA 1 kohm,1/10W
R716VRD-ST2CD102JJ AA 1 kohm,1/6W
R717VRS-TV2AB102JJ AA 1 kohm,1/10W
R718VRD-ST2CD102JJ AA 1 kohm,1/6W
R719VRS-TV2AB102JJ AA 1 kohm,1/10W
R720~723VRS-TV2AB103JJ AA 10 kohm,1/10W
R724VRS-TV2AB102JJ AA 1 kohm,1/10W
R725VRS-TV2AB822JJ AA 8.2 kohms,1/10W
R726VRD-ST2CD102JJ AA 1 kohm,1/6W
R727VRD-ST2CD122JJ AA 1.2 kohms,1/6W
R728VRS-TV2AB182JJ AA 1.8 kohms,1/10W
R729VRS-TV2AB222JJ AA 2.2 kohms,1/10W
R730VRS-TV2AB822JJ AA 8.2 kohms,1/10W
R731VRD-ST2CD102JJ AA 1 kohm,1/6W
R732VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R733VRS-TV2AB182JJ AA 1.8 kohms,1/10W
R734VRS-TV2AB222JJ AA 2.2 kohms,1/10W
R735VRS-TV2AB392JJ AA 3.9 kohms,1/10W
R736VRS-TV2AB562JJ AA 5.6 kohms,1/10W
R737VRD-ST2CD822JJ AA 8.2 kohms,1/6W
R743VRD-ST2CD822JJ AA 8.2 kohms,1/6W
R744VRD-ST2CD102JJ AA 1 kohm,1/6W
R745VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R746VRS-TV2AB182JJ AA 1.8 kohms,1/10W
R747VRS-TV2AB222JJ AA 2.2 kohms,1/10W
R748VRS-TV2AB392JJ AA 3.9 kohms,1/10W
R749VRS-TV2AB562JJ AA 5.6 kohms,1/10W
R750VRD-ST2CD822JJ AA 8.2 kohms,1/6W
R751VRS-TV2AB102JJ AA 1 kohm,1/10W
R752VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R753VRS-TV2AB182JJ AA 1.8 kohms,1/10W
R754VRD-ST2CD222JJ AA 2.2 kohms,1/6W
R755VRD-ST2CD392JJ AA 3.9 kohms,1/6W
DESCRIPTION
– 5 –
CD-C1H/CP-C1H
NO.PART CODE
R756VRD-ST2CD562JJ AA 5.6 kohms,1/6W
R757VRS-TV2AB123JJ AA 12 kohms,1/10W
R758VRD-ST2CD822JJ AA 8.2 kohms,1/6W
R759VRS-TV2AB102JJ AA 1 kohm,1/10W
R760VRD-ST2CD122JJ AA 1.2 kohms,1/6W
R765VRS-TV2AB102JJ AA 1 kohm,1/10W
R766VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R767VRS-TV2AB182JJ AA 1.8 kohms,1/10W
R768VRS-TV2AB222JJ AA 2.2 kohms,1/10W
R769VRS-TV2AB392JJ AA 3.9 kohms,1/10W
R770~772VRS-TV2AB821JJ AA 820 ohms,1/10W
R773VRD-ST2CD102JJ AA 1 kohm,1/6W
R774,775VRD-ST2CD681JJ AA 680 ohms,1/6W
R778~784VRS-TV2AB102JJ AA 1 kohm,1/10W
R786,787VRS-TV2AB681JJ AA 680 ohms,1/10W
R788VRS-TV2AB102JJ AA 1 kohm,1/10W
R790VRS-TQ2BB102JJ AA 1 kohm,1/8W
R791VRD-ST2CD102JJ AA 1 kohm,1/6W
R792VRS-TQ2BB102JJ AA 1 kohm,1/8W
R793,794VRD-ST2CD102JJ AA 1 kohm,1/6W
R795VRS-TQ2BB102JJ AA 1 kohm,1/8W
R796VRD-ST2CD102JJ AA 1 kohm,1/6W
R797VRS-TQ2BB102JJ AA 1 kohm,1/8W
R798,799VRS-TV2AB822JJ AA 8.2 kohms,1/10W
R820VRD-ST2CD470JJ AA 47 ohms,1/6W
R822VRD-ST2EE561JJ AA 560 ohms,1/4W
R823,824VRD-ST2CD470JJ AA 47 ohms,1/6W
R825VRD-MN2BD102J J AA 1 kohm,1/8W
R826VRD-ST2EE561JJ AA 560 ohms,1/4W
! R827VRG-ST2EC220JJ AB 22 ohms,1/4W,Fusible
R828VRD-ST2EE101JJ AA 100 ohm,1/4W
R829VRD-ST2EE152JJ AA 1.5 kohms,1/4W
R831VRD-MN2BD223J J AA 22 kohms,1/8W
R834VRD-ST2CD102JJ AA 1 kohm,1/6W
R835VRD-MN2BD333J J AA 33 kohms,1/8W
R851VRD-MN2BD123J J AA 12 kohms,1/8W
R857VRD-ST2CD222JJ AA 2.2 kohms,1/6W
R907,908VRD-MN2BD563J J AA 56 kohms,1/8W
R909,910VRD-MN2BD102J J AA 1 kohm,1/8W
R911,912VRD-MN2BD563J J AA 56 kohms,1/8W
R913,914VRD-ST2EE271JJ AA 270 ohms,1/4W
R915,916VRD-MN2BD102J J AA 1 kohm,1/8W
R919,920VRD-ST2CD472JJ AA 4.7 kohms,1/6W
R921~924VRN-VV3DAR22J J0.22 ohms,2W
R925,926VRD-ST2CD563JJ AA 56 kohms,1/6W
R927,928VRD-RT2HD4R7J J AA 4.7 ohms,1/2W
R929,930VRD-RT2HD3R9J J AA 3.9 ohms,1/2W
R931,932VRD-RT2HD5R6J J AA 5.6 ohms,1/2W
R933,934VRS-VV3DA561JJ560 ohms,2W
R939,940VRD-ST2CD472JJ AA 4.7 kohms,1/6W
R941,942VRD-ST2CD102JJ AA 1 kohm,1/6W
R947,948VRD-ST2CD123JJ AA 12 kohms,1/6W
R971VRD-ST2CD223JJ AA 22 kohms,1/6W
R972VRD-MN2BD223J J AA 22 kohms,1/8W
R973VRD-MN2BD153J J AA 15 kohms,1/8W
R974VRD-MN2BD392J J AA 3.9 kohms,1/8W
R975VRD-ST2CD392JJ AA 3.9 kohms,1/6W
R976VRD-ST2EE470JJ AA 47 ohms,1/4W
R977VRD-MN2BD103J J AA 10 kohm,1/8W
R978VRD-ST2CD104JJ AA 100 kohm,1/6W
R979VRD-MN2BD333J J AA 33 kohms,1/8W
R985VRS-VV3DA391JJ390 ohms,2W
R987,988VRD-MN2BD332J J AA 3.3 kohms,1/8W
R989~992VRD-RT2HD100JJ AA 10 ohm,1/2W
! R993,994VRG-ST2HC101JJ AB 100 ohm,1/2W,Fusible
R995VRD-MN2BD183J J AA 18 kohms,1/8W
R996VRD-ST2CD473JJ AA 47 kohms,1/6W
R997VRD-ST2CD332JJ AA 3.3 kohms,1/6W
R998VRD-MN2BD563J J AA 56 kohms,1/8W
R999VRD-ST2CD100JJ AA 10 ohm,1/6W
RA01VRD-ST2CD102JJ AA 1 kohm,1/6W
RA02~05VRD-MN2BD102J J AA 1 kohm,1/8W
RA06~10VRD-ST2CD102JJ AA 1 kohm,1/6W
RA11~13VRD-MN2BD102J J AA 1 kohm,1/8W
RA14VRD-ST2CD102JJ AA 1 kohm,1/6W
RA17VRD-MN2BD821J J AA 820 ohms,1/8W
RA19~23VRD-ST2CD102JJ AA 1 kohm,1/6W
RA24VRD-MN2BD103J J AA 10 kohm,1/8W
RA25~28VRD-MN2BD102J J AA 1 kohm,1/8W
RA29VRD-MN2BD473J J AA 47 kohms,1/8W
RA30~33VRD-ST2CD102JJ AA 1 kohm,1/6W
RA34,35VRD-MN2BD102J J AA 1 kohm,1/8W
PRICE
RANK
DESCRIPTION
NO.
RA36,37VRD-ST2CD102JJ AA 1 kohm,1/6W
RA38,39VRD-MN2BD102J J AA 1 kohm,1/8W
RA40VRD-ST2CD102JJ AA 1 kohm,1/6W
RA41,42VRD-MN2BD102J J AA 1 kohm,1/8W
RA43VRD-ST2CD472JJ AA 4.7 kohms,1/6W
RA44,45VRD-MN2BD102J J AA 1 kohm,1/8W
RA46,47VRD-ST2CD102JJ AA 1 kohm,1/6W
RA48,49VRD-MN2BD102J J AA 1 kohm,1/8W
RA51VRD-ST2CD102JJ AA 1 kohm,1/6W
RA52,53VRD-MN2BD102J J AA 1 kohm,1/8W
RA54VRD-ST2CD102JJ AA 1 kohm,1/6W
RA55VRD-MN2BD102J J AA 1 kohm,1/8W
RA58VRD-ST2CD102JJ AA 1 kohm,1/6W
RA59VRD-MN2BD102J J AA 1 kohm,1/8W
RA61VRD-ST2CD102JJ AA 1 kohm,1/6W
RA62,63VRD-MN2BD102J J AA 1 kohm,1/8W
RA68,69VRD-MN2BD102J J AA 1 kohm,1/8W
RA70VRD-ST2CD102JJ AA 1 kohm,1/6W
RA71,72VRD-MN2BD102J J AA 1 kohm,1/8W
RA73VRD-MN2BD223J J AA 22 kohms,1/8W
RA75VRD-MN2BD102J J AA 1 kohm,1/8W
RA79,80VRD-MN2BD102J J AA 1 kohm,1/8W
RA81VRD-ST2CD102JJ AA 1 kohm,1/6W
RA82,83VRD-MN2BD102J J AA 1 kohm,1/8W
RA87,88VRD-ST2CD102JJ AA 1 kohm,1/6W
RA91~94VRD-MN2BD102J J AA 1 kohm,1/8W
RA95,96VRD-ST2CD102JJ AA 1 kohm,1/6W
RA97,98VRD-MN2BD102J J AA 1 kohm,1/8W
RA99VRD-ST2CD102JJ AA 1 kohm,1/6W
RD01VRD-MN2BD102J J AA 1 kohm,1/8W
RD02VRD-ST2CD102JJ AA 1 kohm,1/6W
RD03,04VRD-MN2BD102J J AA 1 kohm,1/8W
RD05,06VRD-MN2BD103J J AA 10 kohm,1/8W
RD07,08VRD-MN2BD222J J AA 2.2 kohms,1/8W
RD09VRD-ST2CD223JJ AA 22 kohms,1/6W
RD10,11VRD-MN2BD103J J AA 10 kohm,1/8W
RD12VRD-MN2BD473J J AA 47 kohms,1/8W
RD13,14VRD-ST2CD103JJ AA 10 kohm,1/6W
RD15VRD-ST2EE271JJ AA 270 ohms,1/4W
RD16VRD-ST2CD102JJ AA 1 kohm,1/6W
RD21VRD-ST2CD683JJ AA 68 kohms,1/6W
RD22VRD-MN2BD683J J AA 68 kohms,1/8W
RD23,24VRD-MN2BD392J J AA 3.9 kohms,1/8W
RD25,26VRD-MN2BD471J J AA 470 ohms,1/8W
RD27VRD-ST2CD683JJ AA 68 kohms,1/6W
RD28VRD-MN2BD683J J AA 68 kohms,1/8W
RD29,30VRD-MN2BD122J J AA 1.2 kohms,1/8W
RD31,32VRD-MN2BD822J J AA 8.2 kohms,1/8W
RD33,34VRD-MN2BD472J J AA 4.7 kohms,1/8W
RD35VRD-MN2BD105J J AA 1 Mohm,1/8W
RD36VRD-MN2BD101J J AA 100 ohm,1/8W
RD37VRD-ST2EE271JJ AA 270 ohms,1/4W
RD38VRD-ST2CD332JJ AA 3.3 kohms,1/6W
RD39VRD-MN2BD104J J AA 100 kohm,1/8W
RD41VRD-MN2BD472J J AA 4.7 kohms,1/8W
RD42VRD-ST2CD472JJ AA 4.7 kohms,1/6W
RD43,44VRD-ST2CD224JJ AA 220 kohms,1/6W
RD69VRD-ST2CD103JJ AA 10 kohm,1/6W
RD70VRD-MN2BD103J J AA 10 kohm,1/8W
RD71,72VRD-ST2CD682JJ AA 6.8 kohms,1/6W
RD73VRD-ST2CD472JJ AA 4.7 kohms,1/6W
RD75VRD-ST2CD473JJ AA 47 kohms,1/6W
RD76VRD-ST2CD103JJ AA 10 kohm,1/6W
RD77,78VRD-MN2BD472J J AA 4.7 kohms,1/8W
RM01VRD-MN2BD333J J AA 33 kohms,1/8W
RM02VRD-MN2BD223J J AA 22 kohms,1/8W
RM03VRD-MN2BD473J J AA 47 kohms,1/8W
RM04VRD-ST2CD104JJ AA 100 kohm,1/6W
RM05VRD-ST2CD103JJ AA 10 kohm,1/6W
RM06VRD-ST2CD222JJ AA 2.2 kohms,1/6W
RM09VRD-MN2BD103J J AA 10 kohm,1/8W
RM10VRD-ST2CD103JJ AA 10 kohm,1/6W
RM11,12VRD-ST2CD222JJ AA 2.2 kohms,1/6W
RM23,24VRD-ST2CD821JJ AA 820 ohms,1/6W
RM25VRD-MN2BD102J J AA 1 kohm,1/8W
RP01,02VRD-MN2BD104J J AA 100 kohm,1/8W
RP05,06VRD-MN2BD222J J AA 2.2 kohms,1/8W
RP07VRD-MN2BD102J J AA 1 kohm,1/8W
RP08VRD-ST2CD102JJ AA 1 kohm,1/6W
RP09,10VRD-ST2CD103JJ AA 10 kohm,1/6W
RP11,12VRD-MN2BD473J J AA 47 kohms,1/8W
RP13,14VRD-ST2CD562JJ AA 5.6 kohms,1/6W
PRICE
RANK
DESCRIPTIONPARTS CODE
– 6 –
CD-C1H/CP-C1H
PART CODENO.PARTS CODE
RP15,16VRD-ST2EE221JJ AA 220 ohms,1/4W
RP33VRD-ST2CD562JJ AA 5.6 kohms,1/6W
RP37VRD-MN2BD683J J AA 68 kohms,1/8W
RP38VRD-ST2CD683JJ AA 68 kohms,1/6W
RP41,42VRD-ST2CD222JJ AA 2.2 kohms,1/6W
RP46VRD-ST2CD562JJ AA 5.6 kohms,1/6W
RP101RH-QX0009AWZZ J AE Posistor,1.8 ohms
RT05,06VRD-MN2BD273J J AA 27 kohms,1/8W
RT07,08VRD-MN2BD222J J AA 2.2 kohms,1/8W
RT21VRD-ST2CD104JJ AA 100 kohm,1/6W
RT26VRD-ST2CD102JJ AA 1 kohm,1/6W
RT28VRD-MN2BD102J J AA 1 kohm,1/8W
RT29VRD-ST2CD102JJ AA 1 kohm,1/6W
RT30VRD-MN2BD102J J AA 1 kohm,1/8W
RT32VRD-ST2CD103JJ AA 10 kohm,1/6W
RT33,34VRD-ST2CD563JJ AA 56 kohms,1/6W
RT35~37VRD-ST2CD224JJ AA 220 kohms,1/6W
RT48,49VRD-ST2EE391JJ AA 390 ohms,1/4W
RT51~54VRD-ST2CD102JJ AA 1 kohm,1/6W
RY01VRS-TV2AB102JJ AA 1 kohm,1/10W
RY03~10VRS-TV2AB104JJ AA 100 kohm,1/10W
RY12VRS-TV2AB104JJ AA 100 kohm,1/10W
RY14VRS-TV2AB104JJ AA 100 kohm,1/10W
RY16VRS-TV2AB104JJ AA 100 kohm,1/10W
RY18VRS-TV2AB104JJ AA 100 kohm,1/10W
RY20VRS-TV2AB104JJ AA 100 kohm,1/10W
RY22VRS-TV2AB104JJ AA 100 kohm,1/10W
RY29VRS-TV2AB330JJ AA 33 ohms,1/10W
RY30,31VRD-ST2CD330JJ AA 33 ohms,1/6W
RY32~38VRS-TV2AB330JJ AA 33 ohms,1/10W
RY40VRS-TV2AB103JJ AA 10 kohm,1/10W
RY41VRD-ST2CD103JJ AA 10 kohm,1/6W
RY42,43VRS-TV2AB103JJ AA 10 kohm,1/10W
RY44VRD-ST2CD103JJ AA 10 kohm,1/6W
RY45~56VRS-TV2AB104JJ AA 100 kohm,1/10W
RY57VRD-ST2EE390JJ AA 39 ohms,1/4W
PRICE
RANK
DESCRIPTIONNO.
OTHER CIRCUITRY PARTS
BI4A/BQCNWN1086AWZZ J AH Connector Ass’y,3/3Pin
BI851/CNS851 QCNWN1091AWZZ J AG Connector Ass’y,4/4Pin
BIM1QCNWN1005AWZZ J AF Connector Ass’y,4Pin
BIM2/CNS2QCNWN1020AWZZ J AF Connector Ass’y,5/5Pin
BIM3QCNWN0987AWZZ J AH Connector Ass’y,6Pin
CFW1QCNCWZG27AWZZ J AE Socket,27Pin
CFW2QCNCWZG27AWZZ J AE Socket,27Pin
CFW852QCNCWZG14AWZZ J AD Socket,14Pin
CFW903QCNCWZG14AWZZ J AD Socket,14Pin
CNP192LCONPB7BPHK J AC Plug,7Pin
CNP292LCONPB8BPHK J AC Plug,8Pin
CNP392LCONE6P53253 J AC Plug,6Pin
CNP3A92LCONE6P53254 J AC Plug,6Pin
CNP1192LCONE4P53014 J AC Plug,4Pin
CNP1292LCONE5P53253 J AB Plug,5Pin
CNP1392LCONE6P53253 J AC Plug,6Pin
CNP10192LCONE3P53253 J AB Plug,3Pin
CNP10292LCONE7P53253 J AC Plug,7Pin
CNP201QCNCWZS10AWZZ J AK Socket,10Pin
CNP202QCNCW010MAWZZ J AD Plug,12Pin
CNP30192LCONE-2P5268 J AB Plug,2Pin
CNP303QCNCM010MAWZZ J AC Plug,12Pin
CNP851QCNCM698DAFZZ J AB Plug,4Pin
CNP901QCNCM705BAFZZ J AA Plug,2Pin
CNS1A/BQCNWN0858AWZZ J AG Connector Ass’y,8/8Pin
CNS2A/BQCNWN0859AWZZ J AF Connector Ass’y,7/7Pin
CNS3A/BQCNWN0857AFZZ J AK Connector Ass’y,6/6Pin
CNS101A/BQCNWN1095AWZZ J AG Connector Ass’y,3/3Pin
CNS102A/BQCNWN1096AWZZ J AM Connector Ass’y,7/6Pin
CNS701QCNCMZS10AWZZ J AK Socket,10Pin
CNS901QCNWN1090AWZZ J AD Connector Ass’y,2Pin
! F82092LFUSE-T501-EJ AD Fuse,T500mA,250V
! F85392LFUSE-T202-EJ AD Fuse,T2A L 250V
! F85592LFUSE-T252-EJ AD Fuse,T2.5A L 250V
! F857,85892LFUSE-T502-EJ AD Fuse,T5A L 250V
FE301RTUNS0007AWZZ J AT FM Front End
FL701VVKCK1627M/-1J BM FL Display
FW1QCNWN1085AWZZ J AF Flat Cable,27Pin
FW201QCNWN1101AWZZ J AE Flat Wire,8Pin
FW701QCNWN1092AWZZ J AE Flat Cable,6Pin
FW853QCNWN1100AWZZ J AC Flat Wire,3Pin
FW901QCNWN1087AWZZ J AD Flat Cable,5Pin
FW903QCNWN1089AWZZ J AH Flat Cable,14Pin
PRICE
RANK
FW904QCNWN1088AWZZ J AF Flat Wire,8Pin
FWM1QCNWN1093AWZZ J AF Flat Wire,8Pin
FWM2QCNWN1094AWZZ J AH Flat Wire,13Pin
IC95VHPGP1F38T/-1J AL Treminal,Digital Output
J901QJAKM0005AWZZ J AD Jack,Headphones
JT01QSOCJ0205AWZZ J AG Jack,VIDEO/AUX 1
M70192LMTR1854CASY J AS Motor with Chassis [Spindle]
M70292LMTR1854BASY J AP Motor with Gear [Sled]
M90192LMTR1810AJ AK Motor,Air Cooling Fan
MM1(300-3)92PF525-319J AW Motor with Pulley [Tape]
MOB1RMOTV0373AFM1 J AQ Main Cam Motor Ass’y
MOB2RMOTV0373AFM1 J AQ Tray Motor Ass’y
PHM1,2 ————— Phote Interrupter
RL851RRLYD0007AWZZ J AQ Relay
RL901RRLYD0004AWZZ J AP Relay
RX701VHLSPS4421/-1J AL Remote Control Sensor,
SO301QTANC0103AWZZ J AD Terminal,Antenna
SO901QTANA0404AWZZ J AF Terminal,Speaker
SOL1,2 ————— Solenoid
SW701QSW-Z0003AWZZ J AH Switch,Rotary Type
SW702QSW-Z0003AWZZ J AH Switch,Rotary Type [Jog Dial]
SW702AQSW-F9001AWZZ J AE Switch,Push Type [Pickup In]
SW70392LSWICHT1663T J AC Switch,Key Type [X-BASS]
SW70492LSWICHT1663T J AC Switch,Key Type
SW70592LSWICHT1663T J AC Switch,Key Type [SRS Mode]
SW70692LSWICHT1663T J AC Switch,Key Type [SRS Pass]
SW70792LSWICHT1663T J AC Switch,Key Type [FF]
SW70892LSWICHT1663T J AC Switch,Key Type [Stop]
SW70992LSWICHT1663T J AC Switch,Key Type [Edit Normal]
SW71092LSWICHT1663T J AC Switch,Key Type [Edit High]
SW71192LSWICHT1663T J AC Switch,Key Type [Record/Pause]
SW71292LSWICHT1663T J AC Switch,Key Type [Forward Play]
SW71392LSWICHT1663T J AC Switch,Key Type [Dolby-NR]
SW71792LSWICHT1663T J AC Switch,Key Type [Rewind]
SW71892LSWICHT1663T J AC Switch,Key Type [CD Pause]
SW71992LSWICHT1663T J AC Switch,Key Type [Reverse Play]
SW72092LSWICHT1663T J AC Switch,Key Type
SW72192LSWICHT1663T J AC Switch,Key Type [Clock]
SW72292LSWICHT1663T J AC Switch,Key Type [Timer]
SW72392LSWICHT1663T J AC Switch,Key Type [Sleep]
SW72492LSWICHT1663T J AC Switch,Key Type [Video/AUX]
SW72592LSWICHT1663T J AC Switch,Key Type [Tape 1/2]
SW72692LSWICHT1663T J AC Switch,Key Type [Tuner (BAND)]
SW72792LSWICHT1663T J AC Switch,Key Type [CD]
SW72892LSWICHT1663T J AC Switch,Key Type
SW72992LSWICHT1663T J AC Switch,Key Type [RDS EON]
SW73092LSWICHT1663T J AC Switch,Key Type
SW73192LSWICHT1663T J AC Switch,Key Type [RDS ASPM]
SW73292LSWICHT1663T J AC Switch,Key Type [Clear]
SW73392LSWICHT1663T J AC Switch,Key Type [Memory/Set]
SW73492LSWICHT1663T J AC Switch,Key Type [On/Stand-by]
SW73992LSWICHT1663T J AC Switch,Key Type
SW74092LSWICHT1663T J AC Switch,Key Type [Disc 3]
SW74192LSWICHT1663T J AC Switch,Key Type
SW74292LSWICHT1663T J AC Switch,Key Type [Disc 2]
SW74392LSWICHT1663T J AC Switch,Key Type
SW74492LSWICHT1663T J AC Switch,Key Type [Disc 1]
SWB101,102 QSW-F0353AFZZ J AD Switch,Leaf Type [Cam1,2]
SWB103,104 QSW-F0353AFZZ J AD Switch,Leaf Type [Cam3,4]
SWB105QSW-P0920AFZZ J AC Switch,Push Type [CD Eject]
SWB107QSW-P0920AFZZ J AC Switch,Push Type [CD In]
SWB108QSW-P0920AFZZ J AC Switch,Push Type [CD Set]
SWE1 ————— Switch,Leaf Type [Tape 1 Play]
SWE2 ————— Switch,Leaf Type [Tape 1 CrO
SWE4 ————— Switch,Leaf Type [Tape 2 Play]
DESCRIPTION
(Supplies at REF No.PWB-G/
PWB-H)
SPS4421
(Supplies at REF No.PWB-G/
PWB-H)
[Volume Up/Down]
[Equalizer/Demo]
[Reverse Mode]
[RDS Programme Type/Traffic
Information Search]
[RDS Display Mode]
[Disc 3 Open/Close]
[Disc 2 Open/Close]
[Disc 1 Open/Close]
(Supplies at REF No.PWB-G)
2]
(Supplies at REF No.PWB-G)
(Supplies at REF No.PWB-H)
– 7 –
CD-C1H/CP-C1H
NO.PART CODE
SWE5 ————— Switch,Leaf Type [Tape 2 CrO2]
SWE7 ————— Switch,Leaf Type
SWE8 ————— Switch,Leaf Type
TP45192LCONE3P53253 J AB Plug,3Pin [Test Point]
WT853QCNCW039CAWZZ J AD Socket,3Pin
WT90292LCONE5P52287 J AC Socket,5Pin
WTM192LCONE8P52287 J AD Plug,8Pin,Wire Trap
WTM2QCNCW012NAWZZ J AE Plug,13Pin,Wire Trap
PRICE
RANK
DESCRIPTION
(Supplies at REF No.PWB-H)
[Tape 2 Side A FP]
(Supplies at REF No.PWB-H)
[Tape 2 Side B FP]
(Supplies at REF No.PWB-H)
CD MECHANISM PARTS
301NGERH0011AWZZ J AC Gear,Middle
302NGERH0012AWZZ J AC Gear,Drive
303MLEVP0010AWZZ J AC Rail,Guide
304NSFTM0002AWFW J AE Shaft,Guide
305PCUSG0427AFSC J AC Cushion
! 306RCTRH8164AFZZ J BF Pickup Unit Ass’y
306- 1 ————— Pickup Unit
306- 2NGERR0043AFZZ J AC Gear,Rack
306- 3MSPRC0961AFZZ J AA Spring,Rack
307PCUSG0001AWSA J AD Insulator
308PCUSG0004AWSA J AD Insulator
70192L2R6S+6CZJ AB Screw,ø2.6×6mm
702XHBSD20P05000J AA Screw,ø2×5mm
703XBBSD20P03000J AA Screw,ø2×3mm
70492L1R5WC3R8R25 J AA Washer,ø1.5×ø3.8×0.25mm
M70192LMTR1854CASY J AS Motor with Chassis [Spindle]
M70292LMTR1854BASY J AP Motor with Gear [Sled]
SW702AQSW-F9001AWZZ J AE Switch,Push Type [Pickup In]
(Not Replacement Item)
CHANGER MECHANISM
101LCHSM0037AWZZ J AP Main Base
102LANGF0024AWZZ J AE Top Board
103NROLP0007AWZZ J AB Rollar,Cam Guide
104NPLYR0004AWZZ J AC Pulley,Drive
105NGERH0052AWZZ J AC Gear,Idler
106NGERH0053AWZZ J AB Gear,Cam
107NGERH0054AWZZ J AB Gear,Midle
108NGERH0057AWZZ J AB Gear,Tray Idler
109MCAMP0127AFZZ J AR Main Cam
110MLEVP0056AWZZ J AC Lever,Front Switch
111MLEVP0057AWM1 J AC Rear Switch Lever Ass’y
112MLEVP0058AWZZ J AB Lever,Tray Lock
113PGIDM0018AWZZ J AF Holder,Mechanism
114PGIDM0019AWZZ J AE Holder,Stabilizer
115LHLDM1008AWZZ J AD Stabilizer
116PGIDM0017AWZZ J AC Guide,Mechanism Holder
119GCOVA1152AWZZ J AL Tray,Disc Guide
120GCOVA1153AWZZ J AF Tray,Disc
121LANGF0025AWZZ J AB Bracket,Switch
122NSFTL0001AWZZ J AB Shaft,Tray Change
123MSPRD0078AWFJ J AB Spring,Tray Switch
124MSPRD0080AWFJ J AB Spring,Tray Lock Lever
125MSPRD0079AWFJ J AB Spring,Disc Stop
126NBLTK0028AWZZ J AB Belt,Tray Drive
127NBLTK0027AWZZ J AB Belt,Cam Drive
128PMAGF0001AWZZ J AF Magnet
12992LN-BAND1318A J AA Nylon Band,80mm
130PGUMS0012AWZZ J AB Tray Rubber
131LANGF0028AWZZ J AB Bracket,Mechanism Holder
132LCHSM0038AWZZ J AK Changer Box
133NGERH0055AWZZ J AC Gear,Center
134NGERH0056AWZZ J AB Gear,Center Tray
135NGERH0058AWZZ J AB Gear,Tray Drive
136MLEVP0052AWZZ J AC Lever,Tray Change
137MLEVP0053AWZZ J AC Lever,Top Joint
138MLEVP0054AWZZ J AC Lever,Midle Joint
139MLEVP0055AWZZ J AC Lever,Bottom Joint
801XBPSD26P04000J AA Screw,ø2.6×4mm
802XEBSD20P07000J AB Screw,ø2×7mm
803XEBSD20P06000J AA Screw,ø2×6mm
804XEBSD26P12000J AA Screw,ø2.6×12mm
805LX-EZ0005AWFDJ AA Screw,ø2.6×10mm
MOB1RMOTV0373AFM1 J AQ Main Cam Motor Ass’y
MOB2RMOTV0373AFM1 J AQ Tray Motor Ass’y
NO.
SWB101,102 QSW-F0353AFZZJ AD Switch,Leaf Type [Cam1,2]
SWB103,104 QSW-F0353AFZZJ AD Switch,Leaf Type [Cam3,4]
SWB105QSW-P0920AFZZ J AC Switch,Push Type [CD Eject]
SWB106QSW-P0920AFZZ J AC Switch,Push Type
SWB107QSW-P0920AFZZ J AC Switch,Push Type [CD In]
SWB108QSW-P0920AFZZ J AC Switch,Push Type [CD Set]
PRICE
RANK
DESCRIPTIONPARTS CODE
[CD Tray Close]
CABINET PARTS
20192LCAB2766AS1J BE Front Panel Ass’y
201- 1 ————— Front Panel
201- 2PCUSG0022AWZZ J AB Cushion,Leg
201- 3HDECP0043AWSA J AE Panel,Function
20292LPNL2766AS1JFL Panel Ass’y
202- 1HBDGB1006AWSA J AD Badge,SHARP
202- 2HDECQ0343AWSA J AG Panel,FL Display
203KNOB2695AASY1 J AR Disc No.Button Ass’y
204KNOB2695BASY2 J AT Operation Button Ass’y
205GCAB-1049AWSA J AR Top Cabinet
206GCOVA1173AWSA J AK Cover,Disc Tray 1
207GCOVA1174AWSA J AK Cover,Disc Tray 2
208GCOVA1175AWSA J AK Cover,Disc Tray 3
209JKNBZ0465AWSA J AF Button,RDS
211GDORF0049AWSA J AM Cassette Holder,Tape 1
212GDORF0050AWSA J AM Cassette Holder,Tape 2
213GITAR0325AWSA J AT Rear Panel
214GITAS0044AWSA J AP Side Panel,Left
215GITAS0045AWSA J AP Side Panel,Right
217HDECQ0281AWSA J AH Decoration Plate,Cassette
218HDECQ0282AWSA J AH Decoration Plate,Cassette
219HDECQ0285AWSA J AL Panel,Operation Botton
220JKNBK0052AWSA J AF Knob,Volume Up/Down
221JKNBK0053AWSA J AF Knob,Jog Dial
222JKNBZ0455AWSA J AF Button,On/Stand-by
223JKNBZ0457AWSA J AF Button,Function
224JKNBZ0458AWSA J AF Button,X-BASS
225JKNBZ0459AWSA J AF Button,SRS
226LANGK0057AWFW J AE Bracket,Heat Sink,Front
227LANGK0058AWFW J AE Bracket,Heat Sink,Rear
228LANGK0059AWFW J AD Bracket,Fan Motor
229LANGK0104AWFW J AK Bracket,Main PWB
230LANGK0110AWFW J AE Bracket,Cassette Lock,Tape 1
231LANGK0111AWFW J AE Bracket,Cassette Lock,Tape 2
232LANGK0113AWFW J AL Bracket,Main PWB Supt,Right
! 233LBSHC0002AWZZ J AD Bushing,AC Power Supply Cord
234LCHSM0065AWFW J AV Main Chassis
235LCHSZ0012AWZZ J AQ Holder,CD Mechanism
237LHLDZ1171AWZZ J AF Holder,FL Display
238LHLDZ1172AWZZ J AD Holder,LED Operation,Left
239LHLDZ1173AWZZ J AD Holder,LED Operation,Right
240LHLDZ1174AWZZ J AD Holder,LED Disc No.
241MLIFP0003AWZZ J A E Damper,Cassette Holder
242MLOKC0001AWZZ J AD Cassette Lock,Tape 1
243MLOKC0002AWZZ J AD Cassette Lock,Tape 2
244MSPRD0092AWFJ J AB Spring,Cassette,Tape 1
245MSPRD0093AWFJ J AB Spring,Cassette,Tape 2
246MSPRD0109AWFJ J AB Spring,Cassette Lock,Tape 1
247MSPRD0110AWFJ J AB Spring,Cassette Lock,Tape 2
248NFANP0001AWZZ J AD Rotary Fan
249PCUSG0022AWZZ J AB Cushion,Leg
250PRDAR0065AWFW J AD Heat Sink,Diode
251PRDAR0095AWFW J BB Heat Sink,Main
252PRDAR0096AWFW J AM Heat Sink,Sub
! 253QACCE0008AW00 J AG AC Power Supply Cord
254QCNWN1102AWZZ J AE Lead Wire with Lug
25892LCAUT1706A1J AC Label,Class 3
25992LCAUT1706BJ AA Label,Laser Caution
26092LCLMP1810AJ AC Wire Holder
26192LCSPR1431CJ AA Spring,Rotary Fan
26392LN-BAND1318A J AA Nylon Band,80mm
26592LRDAT1587AJ AC Heat Sink,Diode
! 266QFSHD0001AWZZ J AB Holder,Fuse
! 26792LLUG1746AJ AA Lug,Terminal
268RCORF0002AWZZ J AE Core
269PFLT-0037AWZZJFelt
(Not Replacement Item)
Holder,Tape 1
Holder,Tape 2
– 8 –
CD-C1H/CP-C1H
PART CODENO.PARTS CODE
300KMECB0006AWZZ J BS Tape Mechanism Ass’y
300- 192PF513-810J AY Head,Record/Playback/Erase
300- 292PF513-811J AX Head,Playback [Tape 1]
300- 3(MM1)92PF525-319J AW Motor with Pulley [Tape]
300- 4(PWB-H) 92PF567-612J AX Tape 2 Mechanism PWB Ass’y
300- 5(PWB-G) 92PF567-613J AV Tape 1 Mechanism PWB Ass’y
300- 692PFF17G-31J AG Belt,Main
300- 792PF514-118J AK Pinch,Roller Ass’y,Right
300- 892PF514-119J AK Pinch,Roller Ass’y,Left
300- 992PFF18W-12J AF Belt,Fast Forward/Rewind
300-1092PFF19D-21J AG Belt,Joint
601LX-HZ0009AWFD J AC Screw,Special
602LX-HZ0082AFZZJ AA Screw,ø4×8mm
603LX-JZ0010AFFDJ AA Screw,ø3×10mm
604LX-JZ0022AFFDJ AA Screw,ø3×8mm
605XBBSD20P04000J AA Screw,ø2×4mm
606XJBSD30P10000J AA Screw,ø3×10mm
607XHBSD26P04000J AA Screw,ø2.6×4mm
608XHBSD30P06000J AA Screw,ø3×6mm
609XEBSD30P10000J AA Screw,ø3×10mm
610XJBSD30P14000J AA Screw,ø3×14mm
611XJBSF30P10000J AA Screw,ø3×10mm
612XJBSF30P12000J AA Screw,ø3×12mm
613XJSSD30P10000J AA Screw,ø3×10mm
614XJBSD30P12000J AA Screw,ø3×12mm
PRICE
RANK
DESCRIPTIONNO.
[Tape 2]
ACCESSORIES/PACKING PARTS
QANTL0005AWZZ J AG AM Loop Antenna
SPAKA0193AWZZ J AN Packing Add.
SPAKC0646AWZZ J AZ Packing Case
SPAKP0032AWZZ J AF Polyethylene Bag,Unit
SPAKZ0375AWZZ J AF Pad,Changer
SPAKZ0378AWZZ J AE Pad,Protection (B)
TINSZ0302AWZZJ AU Operation Manual
TLABE0236AWZZ JLabel,Bar Code
92LFANT1535AJ AF FM Antenna
92LLABL372CJ AB Label,Serial No.
RRMCG0125AWSA J AX Remote Control
92LLID1782AJ AQ Battery Lid,Remote Control
P.W.B. ASSEMBLY (Not Replacement Item)
PWB-A1~392LPWB2766DPLS J — Display/CD Switch/Headphone
PWB-B92LPWB2766MANS J— Main
! PWB-C1~392LPWB2766PWRS J — Power Amp./Power Supply/CD
PWB-D92LPWB2766TUNS J — Tuner
PWB-EQPWBF0027AWZZ J AD CD Motor (PWB Only)
PWB-FQPWBF0322AWZZ J AC Tray Switch (PWB Only)
PWB-G92PF567-613J AV Tape 1 Mechanism
PWB-H92PF567-612J AX Tape 2 Mechanism
(Combined Ass’y)
Servo (Combined Ass’y)
PRICE
RANK
DESCRIPTION
CP-C1H
SPEAKER BOX PARTS
90192L20100PC1W10 J AQ Net Frame Ass’y
90292L200L0PC1W20 J BG Front Panel Ass’y,Left
90292L200R0PC1W20 J BG Front Panel Ass’y,Right
90392L100L2PC1W10 JSpeaker Box Ass’y,Left
90392L100R2PC1W10 JSpeaker Box Ass’y,Right
90492L205L0PC1W00 J AL Speaker Duct,Left
90492L205R0PC1W00 J AL Speaker Duct,Right
90592LPCATIXL12J AB Holder,Catcher
90692L21000PC1W00 J AR Holder,Woofer
90792L3141CPC1W10 J AQ C1 + Cord Ass’y
90892L44010212800J AE Cushion,Speaker Duct
90992LG53-1203-08J AD Cushion,Speaker Cord,Woofer
91092L44210610100J AE Cushion,Front Panel
91192L42710000300J AH Bracket,Tweeter
91292L6000CPC1H00 JLabel,Specification
91392L411S84016AB J AD Screw,ø4×16mm
91492L411B840120PJ AD Screw,ø4×12mm
91592L411N84020AB J AE Screw,ø4×20mm
91692L411R130100P JScrew,ø3×10mm
91792LN44-4025-45J AE Screw,ø4×25mm
SP1,2VSP0020WB906A J BN Woofer
SP3,4VSP0080TBN86A J BC Tweeter
SP5,692L303R0300510J AN Super Tweeter
(2.7 µF,100V,Film Capacitor)
ACCESSORIES/PACKING PARTS
92L3191CPC1W10 J AQ Speaker Cord Ass’y
92L6100CPC1H00 JLabel Feature,Speaker
92L70032001110J AE Polyethylene Bag,Speaker
92L71525002700J AF Mirror Mat
92L720BCPC1W00 J AP Packing Add.,Bottom,Speaker
92L720TCPC1W00 J AP Packing Add.,Top,Speaker
92L74231001100J AF Pad,Speaker
– 9 –
A
B
C
D
E
F
G
H
1
23456
CD-C1H
CD-C1H/CP-C1H
306
306-2
306-1
701
304
701
704
306-3
302
301
702
702
303
703x2
M701
307
305x2
M702
308
SW702A
PWB-E
Figure 10 CD MECHANISM EXPLODED VIEW
– 10 –
CD-C1H/CP-C1H
CD-C1H
A
120
802
125
102
114
802
128
112
B
119
124
120
115
112
119
124
804
116
C
113
120
112
D
CD Mechanism
805x4
119
124
122
804
109
E
F
G
H
PWB-F
SWB
105
802
126
103
110x2
SWB
106
111x2
SWB
107
SWB
108
104
107
803x2
801x2
123x4
131
130
103
MOB2
129
127
104
105
MOB1
80mm
106
108
103
101
801
x2
SWB101~104
133
804x2
121
803
108x3
135
108x3
135
134
108x3
135
134
134
132
139
138
137
108
135
136
108
135
136
108
135
136
1
23456
Figure 11 CHANGER MECHANISM XPLODED VIEWCD-CIW
– 11 –
CD-C1H/CP-C1H
A
B
C
D
E
F
G
H
1
23456
CD-C1H
205
612x2
214
611x3
240
223
249
604
PWB-A3
FL701
201
201-3
201-1
201-2
202
202-1
202-2
With
SW702
221
242
219
211
246
601
607x2
237
201-2
300-10
SWE7
300-4
220
(TAPE2 MECHANISM
PWB-H)
SWE4
300-8
300-2
230
300
TAPE MECHANISM
ASSEMBLY
212
209
300-7
300-8
238
SWE5
606x12
SW702
239
222
SWE8
609x2
269
269
225
241
300-6
300-9
300-9
300-5
(TAPE1MECHANISM
PWB-G)
SWE1
300-7
300-1
231
604
SWE2
PWB-D
243
609
241
613x6
247
606x3
SW701
PWB-A1
224
609
300-3
(MM1)
300-6
608
203
CD Changer
Block
207
208
204
603x2
603x2
603x4
229
254
PWB-A2
206
PWB-B
604
PWB-C1
260x2
605
x2
261
608
248
614x2
606
266x2
603
x2
259
610x2
M901
606x3
606
x2
608
x2
228
606x2
235
Q820
IC901
608
Q822
603
232
Q824
Silicon
Grease
Silicon
Grease
226
Silicon
Grease
251
250
608x2
252
260
265
D851
606
266x6
215
606
D850
610
603
610
612x2
PWB-C3
606x3
PWB-C4
606
x2
227
602x4
606
IC95
611x12
608
T851
with
IC95
603
268x2
267x2
258
253
233
PWB-C2
213
266
x2
263
601
606x2
234
249
611x3
607x2
217
244
218
245
Note: Only the unit and consumale parts are supplied as aprts supply for the Tape mechanism.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A9803-1813NS•HA•M
SG
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.