TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol warns the user of
uninsulated voltage within the unit
that can cause dangerous electric
shocks.
This symbol alerts the user that there
are important operating and
maintenance instructions in the
literature accompanying this unit.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS UNIT IS
HARMFUL TO THE EYES, DO NOT ATTEMPT TO
DISASSEMBLE THE CABINET.
REFER SERVICING TO QUALIFIED PERSONNEL
ONLY.
•This Player is classified as a CLASS 1 LASER
product.
•The CLASS 1 LASER PRODUCT label is located
on the rear cover.
•This product contains a low power laser device. To
ensure continued safety do not remove any cover
or attempt to gain access to the inside of the
product. Refer all servicing to qualified personnel.
“WARNING–FCC Regulations state that
any unauthorized changes or
modifications to this equipment not
expressly approved by the manufacturer
could void the user’s authority to operate
this equipment.”
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses and can radiate radio frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment
and receiver.
–Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
–Consult the dealer or an experienced radio/TV
technician for help.
1
SAFETY INFORMATION
The following statement applies to BD-AMS20U only.
*
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
Wireless Radio
For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other channels is not possible.
This device is going to be operated in 2.400–2.483GHz frequency range, it is restricted in indoor environment only.
Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal
injuries and property damage if improperly handled. This product has been engineered
and manufactured with the highest priority on safety. However, improper use can result
in electric shock and/or fire. In order to prevent potential danger, please observe the
following instructions when installing, operating and cleaning the product. To ensure
your safety and prolong the service life of your Blu-ray Disc/DVD Player, please read the
following precautions carefully before using the product.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of
time.
14) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
2
IMPORTANT SAFETY INSTRUCTIONS
18) Damage Requiring Service—Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions.
Adjust only those controls that are covered by the operating instructions as
an improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to its
normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a
need for service.
• Water and Moisture—Do not use this product near
water - for example, near a bath tub, wash bowl,
kitchen sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
• Stand—Do not place the product on an unstable
cart, stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or
table recommended by the manufacturer or sold with
the product.
• Selecting the location—Select a place with no direct
sunlight and good ventilation.
• Ventilation—The vents and other openings in the
cabinet are designed for ventilation. Do not cover
or block these vents and openings since insufficient
ventilation can cause overheating and/or shorten the
life of the product. Do not place the product on a bed,
sofa, rug or other similar surface, since they can block
ventilation openings. This product is not designed
for built-in installation; do not place the product in an
enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s
instructions are followed.
19) Replacement Parts—When replacement parts are required, be sure the service
technician has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20) Safety Check—Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the product is in
proper operating condition.
21) The main AC plug is used as disconnect device and shall always remain readily
operable.
Introduction
• Heat—The product should be situated away from
heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce
heat.
• Lightning—For added protection for this product
during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from
the wall outlet. This will prevent damage to the
product due to lightning and power-line surges.
• To prevent fire, never place any type of candle or
flames on the top or near the product.
• To prevent fire or shock hazard, do not expose this
product to dripping or splashing.
No objects filled with liquids, such as vases, should
be placed on the product.
• To prevent fire or shock hazard, do not place the AC
cord under the product or other heavy items.
3
PRECAUTIONS
Precautions on viewing stereoscopic 3D images
• Do not view stereoscopic 3D images if you have a history of photosensitivity, heart
disease or poor health. This may cause the symptoms to worsen.
• If you experience any health problems such as fatigue and discomfort while viewing
stereoscopic 3D images, immediately discontinue viewing. Continuing viewing after
symptoms appear may cause health risks. Take a break until the symptoms have
completely disappeared.
• Ages of 5–6 or over are recommended for viewing stereoscopic 3D images.
Symptoms such as fatigue and discomfort are difficult to determine in young
children, therefore they may suddenly become ill. When viewing 3D images with
children, please watch for eye strain symptoms.
• When viewing stereoscopic 3D images, take a moderate break after watching one
title. Viewing for extended periods may cause visual strain.
Precautions when cleaning this product
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• To clean the outer cabinet, periodically wipe it with a soft cloth (cotton, flannel, etc.).
• For severe dirt, soak a soft cloth (cotton, flannel, etc.) in some neutral detergent
diluted with water, wring the cloth out thoroughly, wipe off the dirt, then wipe again
with a soft, dry cloth.
• Do not use chemicals or a chemically treated cloth for cleaning. It may damage the
cabinet finish.
Notes on using Wireless LAN
• When this player is connected to a wireless LAN network, transmissions between
the wireless LAN adapter (BD-AMS10U: VR-WL25, sold separetely/BD-AMS20U:
supplied) and a wireless LAN compatible broadband router (commercially available)
are carried out.
Precautions on using Wireless LAN
• The following devices, radio stations, etc. use the same frequency bands. Do not use
wireless LAN near them.
Manufacturing/scientific/diagnostic equipment such as pacemakers, etc.
Specified low power radio stations (radio stations that do not require a license)
If this player is used near these devices, there is a possibility that radio wave
interference may occur. Therefore transmission may not be possible or speed may be
reduced.
• Mobile phones, radios, etc. use different radio frequency bands from wireless LAN,
so there will not be any effect on the transmissions of these devices or wireless LAN
if this player is used near them.
However, if a wireless LAN product is placed near one of these devices, audio or
video noise may occur due to the electromagnetic waves that emit from wireless LAN
products.
• Radio waves will pass through the wood, glass, etc. used in standard housing,
however they will not pass through reinforcing bars, metal, concrete, etc. Radio
waves will not pass through walls and floors if these materials are used.
4
DEAR SHARP CUSTOMER
Thank you for your purchase of the SHARP Blu-ray Disc/DVD Player. To ensure safety and many years of trouble-free operation of your product, please read
the Important Safety Instructions carefully before using this product.
Getting Started
Step 1: Unpacking
Make sure the following accessories are provided with the product.
Remote control unit
“AA” size battery (g2)
Page 21
Wireless LAN adapter
(supplied with BD-AMS20U only)
VR-WL25
Step 2: Selecting equipment to connect
Connection varies with the equipment used. Refer to Connection
(Pages 16–20).
Turn off the devices before connecting.
Introduction
Enjoying BD-LIVE and video on demand services (e-Contents)
To enjoy BD-LIVE content or video on demand streaming content on your TV,
after an Internet connection is made, communication setup is required.
Refer to “Communication Setup” (Pages 50–53).
Step 3: Playing back video/picture/music content
Play back video, picture or music content from the desired media source
such as Blu-ray and DVD discs, or via the Internet.
Refer to Playback (Pages 21–42) and video on demand streaming content
(Pages 59–61).
Step 4: Adjust settings to suit your preference
Adjust settings to enjoy various features and other functions for playing
discs/content.
Refer to Settings (Pages 44–58).
Pages 15 and 21
Page 20
5
Contents
Introduction
SAFETY INFORMATION ...................................................................................... 1
IMPORTANT SAFETY INSTRUCTIONS .............................................................. 2
• The illustrations used throughout this operation manual are based on BD-AMS20U.
Streaming content (pp. 59–61)
Shows the Internet streaming services available with this
player.
Appendix (pp. 62–77)
Provides troubleshooting tips and more information.
The illustrations and on-screen displays in this operation manual
are for explanation purposes and may vary slightly from the
actual operations.
7
What would you like to do with this Player?
Watch high quality movies on Blu-ray discs
This Player offers full high-definition Blu-ray disc playback.
Video/Picture/Music Playback (p. 26)
Enjoy stereoscopic and powerful 3D images
This player can play 3D content from 3D compatible Blu-ray discs through
an HDMI cable. To watch 3D images, connect a 3D compatible TV to this
player using an HDMI cable and play the 3D content while wearing 3D
glasses.
Using 3D (p. 24)
Enjoy different kinds of media sources
Use this player to enjoy video, picture or music content from various types
of media sources such as DVDs, USB devices and via the Internet.
About Media Types (pp. 9–12)
Video/Picture/Music Playback (p. 26)
Simple connection and operation through HDMI
This Player is equipped with an HDMI terminal. You can connect it to the TV
using HDMI and no other cable will be needed to enjoy movies. If your TV is
compatible with AQUOS LINK, you can control both the TV and this Player
with simple operations.
Enjoy BD-LIVE functions through the Internet
This Player is compatible with BD-LIVE. You can enjoy bonus content such
as movie trailers through the Internet when playing back BD-Video discs
compatible with BD-LIVE.
Enjoying BONUSVIEW or BD-LIVE (pp. 28–29)
Access to videos, pictures and music from home network
servers
This player can play back video, picture and music data stored on your
home network servers such as a DLNA certified PC.
Accessing DLNA servers (p. 37)
Enjoy video on demand streaming content with higher
image quality on your TV
This player supports video on demand streaming services using the
Internet. By connecting this player to the Internet, you can enjoy various
content streamed on your TV. Also, with this player’s “Super Picture”
function, you can enjoy video streaming images with higher image quality.
Playing back video on demand streaming content (pp. 59–61)
SUPER PICTURE (p. 47)
Connecting to a TV/projector (p. 16)
8
About Media Types
Blu-ray Disc
Blu-ray Disc is the ultimate next generation optical
media format, offering the following key features:
• Largest capacity (25 GB single layer – 50 GB dual layer)
– with over 5 times the amount of content possible with
current DVDs, particularly well suited for high definition
feature films with extended levels of interactive features
• Pristine picture quality with the capability for full high
definition 1920 x 1080p resolution
• Best audio possible with uncompressed surround sound
(higher quality than even theater audio)
• Broadest industry support – ensuring more choice for
consumers in the marketplace
• Hardware products will be backward compatible with
DVDs, allowing continued enjoyment of existing DVD
libraries.
• Disc Durability – new breakthroughs in hard coating
technologies gives Blu-ray Discs the strongest
resistance to scratches and finger prints.
Types of Discs/Media Formats that
Can Be Used with This Player
• The following discs can be played back in this Player.
Do not use an 8 cm (3”) to 12 cm (5”) adapter.
• Use discs that conform to compatible standards as
indicated by the presence of official logos on the disc
label. Playback of discs not complying with these
standards is not guaranteed. In addition, the image
quality or sound quality is not guaranteed even if the
discs can be played back.
Disc Type
BD
Video
Region
code A/ALL
BD-RE/BD-RE DL
BD-R/BD-R DL
DVD
Video
Region
code
Recording
Format
—Audio
BDMV/BDAV
format
Video formatAudio
1/ALL
ALL
1
DVD+RW/DVD+R
DVD-RW/DVD-R
DVD+R DL/DVD-R
DL
Video/VR/
AVCHD
format
(finalized disc
only)
DivX Plus®
HD
(H.264/MKV)
J
JPEG
K
MP3
Audio CD
I
Audio CD
(CD-DA)
CD-RW/CD-RAudio CD
(CD-DA)
J
JPEG
K
MP3
Contents
Disc
Size
12 cm
+ Video
(5”)
(Movie)
12 cm
+ Video
(Movie)
(5”)
8 cm
(3”)
Audio
+ Video
(Movie)
12 cm
(5”)
8 cm
(3”)
Still
image
(JPEG file)
Audio
Audio12 cm
(5”)
Audio
8 cm
(3”)
Still
image
(JPEG file)
Audio
Media Format
USB device
(USB HDD, USB
memory device)
See the following page for details on these terms.
*
Recording Format
DivX Plus® HD
(H.264/MKV)
J
JPEG
K
MP3
Contents
Audio + Video
(Movie)
Still image
(JPEG file)
Audio
• BD/DVD video players and discs have region codes,
which dictate the regions in which a disc can be played.
This Player’s region code is A for BD and 1 for DVD.
(Discs marked ALL will play in any player.)
• BD/DVD video operations and functions may be
different from the explanations in this manual and
some operations may be prohibited due to disc
manufacturer’s settings.
• If a menu screen or operating instructions are displayed
during playback of a disc, follow the operating
procedure displayed.
NOTE
• Playback for some of the discs in the left side column
tables may not be possible depending on the disc.
• “Finalize” refers to a recorder processing a recorded
disc so that it will play in other DVD players/recorders
as well as this player. Only finalized DVD discs will play
back in this player. (This player does not have a function
to finalize discs.)
• Regarding DVD+RW/+R/+R DL discs, only video format
discs (finalized) can be played back. JPEG files, MP3
files, DivX Plus® HD files, etc. cannot be played back.
• Some discs cannot be played back depending on the
recording format.
• DivX playback may not be available depending on the
DivX content and file.
Introduction
9
About Media Types
Discs that Cannot Be Used with
This Player
The following discs cannot be played back or will
not play back properly on this Player. If such a
disc is mistakenly played back, speaker damage
may occur. Never attempt to play back these
discs.
CDG, Video CD, Photo CD, CD-ROM, CD-TEXT,
SVCD, SACD, PD, CDV, CVD, DVD-RAM, DVDAudio, BD-RE with the cartridge, CD-WMA
Discs with unusual shapes cannot be played.
• Discs with unusual shapes (heart-shaped or hexagonal
discs, etc.) cannot be used. The use of such discs will
cause malfunction.
The following BD video discs cannot be played.
• Discs not displaying “A” or “ALL” for the region code
(discs sold outside the authorized marketing area).*
• Discs produced illegally.
• Discs recorded for commercial use.
The region code for this product is A.
*
The following DVD video discs cannot be played.
• Discs not displaying “1” or “ALL” for the region code
(discs sold outside the authorized marketing area).*
• Discs produced illegally.
• Discs recorded for commercial use.
The region code for this product is 1.
*
The following BD-RE/R, DVD-RW/R and
DVD+RW/R discs cannot be played.
• Discs on which data has not been recorded cannot be
played back.
*1
The following Audio CD discs cannot be played.
• Discs containing a signal for the purpose of protecting
copyrights (copy control signal) may not be played back
with this Player.
• This Player has been designed on the premise of
playing back Audio CDs that comply with CD (Compact
Disc) standards.
The following CD-RW/R discs cannot be played.
• Discs on which data has not been recorded cannot be
played back.
• Discs recorded in a format other than an Audio CD and
JPEG/MP3 file format cannot be played back.
• Discs may not be played back depending on their
recording status or the status of the disc itself.
• Discs may not be played back depending on their
compatibility with this Player.
*2
About the JPEG file format
JPEG is a type of file format for storing still-image
files (photos, illustrations, etc.). The Player lets you
play JPEG format still-image files.
File formats that are not compatible.
• Still images in formats other than JPEG (such as TIFF)
cannot be played.
• There may be some files that cannot be played even if
they are in JPEG format.
• Progressive JPEG files cannot be played.
• Moving image files as well as Motion JPEG format files
cannot be played, even though they are JPEG files.
Other files that cannot be played back.
• You may not be able to play some still images which
you have created, touched up, copied or otherwise
edited on your computer.
• You may not be able to play some still images you have
processed (rotated or saved by overwriting other images
you have imported from the Internet or e-mail).
You may experience one or more of the following
symptoms when playing files.
• It may take some time to play files depending on the
number of folders, number of files and volume of data
involved.
• EXIF information will not be displayed. EXIF stands for
Exchangeable Image File Format, and is a standard for
storing interchange information in image files, especially
those using JPEG compression. (Refer to http://exif.org
for more information.)
*3
About the MP3 file format
MP3 files are audio data compressed in the
MPEG1/2 Audio layer-3 file format. “MP3 files” have
“.mp3” as extensions. (Some files that have “.mp3”
extensions or files that have not been recorded in
MP3 format will produce noise or cannot be played.)
Playing the MP3 file format
• The MP3 files are not played in the order they were
recorded.
• It is recommended to record data at a lower speed as
data recorded at a fast speed can produce noise and
may not be able to be played.
• The more folders there are, the longer the reading time.
• Depending on the folder tree, reading MP3 files can take
time.
• The playing time may not be correctly displayed during
MP3 file playback.
The following files cannot be played on this
player.
• When both Audio CD [CD-DA] format and JPEG/
MP3 file formats are recorded on a disc. (The disc is
recognized to be an Audio CD [CD-DA] only tracks in
Audio CD [CD-DA] format are played back.)
• Multi-session discs cannot be played.
About the DivX Plus® HD (H.264/MKV)
file format
• DivX playback may not be available depending on the
DivX content and file.
10
About Media Types
About files/folders for Still images (JPEG
files) and audio data (MP3 files)
You can play still images (JPEG files) /audio data
(MP3 files) with this unit by making folder(s) on discs
or USB devices as shown below.
Example of a folder structure (Disc):
Root
001.jpg/001.mp3
xxx.jpg/xxx.mp3
*
*
01 Folder
xxx Folder
Including the root directory, the maximum number of folders
*
and files in each folder is limited to 256 in total.
Folder
001.jpg/001.mp3
255.jpg/255.mp3
001.jpg/001.mp3
256.jpg/256.mp3
File and folder requirements
• The discs or USB devices which this player can play
back (recognize) are limited to the following properties:
Contains EXIF format files (only JPEG files)
Picture resolution: Between 32 x 32 and 7680 x 4320
pixels (only JPEG files)
Maximum number of folders and files in each folder:
Disc: 256
USB device: 65536
Maximum hierarchy level of folders: 5
File size: 20 MB or less (JPEG files)
200 MB or less (MP3 files)
NOTE
• File and folder names displayed on this player may differ
from those displayed on PCs.
001.jpg/001.mp3
256.jpg/256.mp3
*
*
ABOUT DivX VIDEO
• DivX® is a digital video format created by DivX, LLC, a
subsidiary of Rovi Corporation. This is an official DivX
Certified® device that plays DivX video. Visit divx.com
for more information and software tools to convert your
files into DivX videos.
DivX Certified® to play DivX® and DivX Plus® HD
(H.264/MKV) video up to 1080p HD including premium
content.
ABOUT DivX VIDEO-ON-DEMAND
• This DivX Certified® device must be registered in
order to play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate the DivX
VOD section in your device setup menu. Go to vod.
divx.com for more information on how to complete your
registration.
About Disc Contents
BD Video
Enjoy BD-specific functions including BONUSVIEW
(BD-ROM Profile 1 Version 1.1), such as picture-inpicture, and BD-LIVE (page 29).
For the BD video discs compatible with
BONUSVIEW/BD-LIVE, you can enjoy additional
contents by copying the data from the discs or
downloading it via the Internet. For instance, this
function is capable of playing the original movie as
the primary video while playing video commentary
from the film director on a small screen as a
secondary video.
NOTE
• The available functions differ depending on the disc.
Title, Chapter and Track
•Blu-ray discs and DVDs are divided into “Titles”
and “Chapters”. If the disc has more than one
movie on it, each movie would be a separate
“Title”. “Chapters”, on the other hand, are
subdivisions of titles. (See Example 1.)
•Audio CDs are divided into “Tracks”. You can think
of a “Track” as one tune on an Audio CD. (See
Example 2.)
Example 1: Blu-ray disc or DVD
Title 1Title 2
Chapter 1Chapter 2Chapter 3Chapter 1
Example 2: Audio CD
Track 1Track 2Track 3Track 4
Introduction
11
About Media Types
1
2
3
4
BD-R
AUDIO CD
Icons Used on BD/DVD Video Disc
Cases
The back of the case of a BD/DVD that is
commercially available usually contains various
information about the contents of the disc.
1 2
1. English
2
2. Chinese
3 45
16:9
LB
2
21 3
54 6
DVD Video BD Video
Audio tracks and audio formats
BD and DVD discs can contain up to 8 separate
tracks with a different language on each. The first in
the list is the original track.
This section also details the audio format of each
soundtrack — Dolby Digital, DTS, MPEG etc.
Dolby Digital
A sound system developed by Dolby Laboratories Inc.
that gives movie theater ambience to audio output
when the Player is connected to a Dolby Digital
processor or amplifier.
DTS
DTS is a digital sound system developed by DTS, Inc.
for use in cinemas.
Linear PCM
Linear PCM is a signal recording format used for
Audio CDs and on some DVD and Blu-ray discs. The
sound on Audio CDs is recorded at 44.1 kHz with
16 bits. (Sound is recorded between 48 kHz with 16
bits and 96 kHz with 24 bits on DVD video discs and
between 48 kHz with 16 bits and 192 kHz with 24 bits
on BD video discs.)
2
1. English
2. Chinese
Subtitle languages
This indicates the kind of subtitles.
Screen aspect ratio
Movies are shot in a variety of screen modes.
Camera angle
Recorded onto some BD/DVD discs are scenes
which have been simultaneously shot from a number
of different angles (the same scene is shot from the
front, from the left side, from the right side, etc.).
5
Region code
This indicates the region code (playable region code).
The Icons Used in This Operation
Manual
BD VIDEO
BD-RE
DVD VIDEO
DVD-RW
DVD-R
CD-RW
.............. Indicates the functions that can be
performed for BD Video discs.
.............. Indicates the functions that can be
performed for BD-RE discs.
.............. Indicates the functions that can be
performed for BD-R discs.
...........Indicates the functions that can be
performed for DVD Video discs.
.............. Indicates the functions that can be
performed for DVD-RW discs.
.............. Indicates the functions that can be
performed for DVD-R discs.
.............. Indicates the functions that can be
performed for Audio CDs.
.............. Indicates the functions that can be
CD-R
performed for CD-R discs.
.............. Indicates the functions that can be
performed for CD-RW discs.
.............. Indicates the functions that can be
USB
performed for USB devices.
12
Important Information
Disc Precautions
Be Careful of Scratches and Dust
• BD, DVD and CD discs are sensitive to dust, fingerprints
and especially scratches. A scratched disc may not
be able to be played back. Handle discs with care and
store them in a safe place.
Proper Disc Storage
Place the disc in the center
of the disc case and store the
case and disc upright.
Avoid storing discs in locations
subject to direct sunlight,
close to heating appliances or
in locations of high humidity.
Do not drop discs or subject
them to strong vibrations or
impacts.
Avoid storing discs in locations
where there are large amounts
of dust or moisture.
Handling Precautions
• If the surface is soiled, wipe gently with a soft, damp
(water only) cloth. When wiping discs, always move the
cloth from the center hole toward the outer edge.
• Do not use record cleaning sprays, benzene, thinner,
static electricity prevention liquids or any other solvent.
• Do not touch the surface.
• Do not stick paper or adhesive labels to the disc.
• If the playing surface of a disc is soiled or scratched,
the Player may decide that the disc is incompatible
and eject the disc tray, or it may fail to play the disc
correctly. Wipe any dirt off the playing surface with a
soft cloth.
Cleaning the Pick Up Lens
• Never use commercially available cleaning discs. The
use of these discs can damage the lens.
• Request the nearest service center approved by SHARP
to clean the lens.
Warnings about dew formation
• Condensation may form on pick up lens or disc in the
following conditions:
− Immediately after a heater has been turned on.
− In a steamy or very humid room.
− When the Player is suddenly moved from a cold
environment to a warm one.
When condensation forms:
• It becomes difficult for the Player to read the signals
on the disc and prevents the Player from operating
properly.
To remove condensation:
• Take out the disc and leave the Player with the
power off until the condensation disappears. Using
the Player when there is condensation may cause
malfunction.
License and Copyright
Audio-visual material may consist of copyrighted
works which must not be recorded without the
authority of the owner of the copyright. Refer to
relevant laws in your country.
• “This item incorporates copy protection technology
that is protected by U.S. patents and other intellectual
property rights of Rovi Corporation. Reverse engineering
and disassembly are prohibited.”
• Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
• HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
• “x.v.Color” and “x.v.Color” logo are trademarks of Sony
Corporation.
• Java is a registered trademark of Oracle and/or its
affiliates.
• “BONUSVIEW” logo is a trademark of Blu-ray Disc
Association.
• “AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
• “Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of
Blu-ray Disc Association.
• Netflix and the Netflix logo are the registered trademarks
of Netflix, Inc.
• YouTube is a trademark of Google Inc.
• VUDU™ is a trademark of VUDU, Inc.
• DivX®, DivX Certified®, DivX Plus® HD and associated
logos are trademarks of Rovi Corporation or its
subsidiaries and are used under license.
• LC
_LCFONT+ and LC logo
mark are registered trademarks of SHARP Corporation.
This product is embedded with LC Font technology,
which was developed by SHARP Corporation for clearly
displaying easy-to-read characters on an LCD screen.
However, other non-LCD fonts are used for displaying
some screen pages.
• MHL, the MHL logo, and Mobile High-Definition Link are
trademarks or registered trademarks of MHL licensing,
LLC.
• “Copyright 2004-2010 Verance Corporation. Cinavia™
is a Verance Corporation trademark. Protected by U.S.
Patent 7,369,677 and worldwide patents issued and
pending under license from Verance Corporation. All
rights reserved.”
ENERGY STAR® Program Information
Products that have earned
the ENERGY STAR
designed to protect the
environment through
superior energy efficiency.
ENERGY STAR® is a U.S. registered mark.
®
are
Introduction
13
Major Components
Main Unit (Front)
1
1Disc tray (p. 26)
2 OPEN/CLOSE (p. 26)3 d PLAY (p. 26)4 H STOP (p. 26)5 POWER (p. 22)
POWER (ON/STANDBY) indicator (p. 22)
67 BD/DVD/CD mode indicator (p. 22)
23456
78 910
8 Remote control sensor (p. 21)9 Front panel display (p. 22)
• The elapsed time is displayed during
playback.
• When skipping is performed,
the chapter (or track) number is
displayed.
0 USB2 terminal (pp. 18, 28, 32, 35)
Main Unit (Rear)
1
*
32
45
1
1AC cord (p. 21)
2 MHL/HDMI INPUT terminal (p. 43) (3 HDMI OUT terminal (p. 16)4 DIGITAL AUDIO OUT OPTICAL terminal (p. 17)5 ETHERNET terminal (p. 19)6 W-LAN
J
Only use the recommended wireless LAN adapter (VR-WL25, supplied with BD-AMS20U only)
with this player.
2
/USB1 terminal (pp. 18, 20, 28, 32)
*
NOTE
• When you insert or remove a USB device, be sure to turn off the main power of this
player and the USB device (only if connecting a USB HDD). Also, be sure to set “Quick
Start” to “No” (See page 47) before inserting or removing the device. If you insert or
remove the device with the player or Quick Start on, the data may become damaged.
6
1
for BD-AMS20U only)
*
14
Major Components
Remote Control Unit
10
11
12
13
1POWER (p. 22)
2 m OPEN/CLOSE (p. 26)
1
16
2
3
17
4
5
6
7
8
18
19
20
21
9
3 AUDIO (p. 40), SUBTITLE (p. 40)4 Number buttons (p. 42)5 VUDU (p. 60)6 T SKIP/k (pp. 30, 38)
7 U SKIP/l (pp. 30, 38)
8 F PAUSE (pp. 34, 35, 36, 38)9 d PLAY (p. 26)
0 TOP MENU/TITLE LIST (pp. 27, 30)
Q Cursor buttons (a/b/c/d), ENTER (pp. 23, 44)
W EXIT (pp. 34, 37, 44)E A (Red), B (Green), C (Blue), D (Yellow)
(pp. 30, 31, 36, 53)
(Lock) (See below.)
RT NETFLIX (p. 59)Y DISPLAY (pp. 27, 39)U TV control buttons (p. 23)I FUNCTION (pp. 39, 41)
O V FWD (p. 38)PS REV (p. 38)
A H STOP (p. 26)
SPOP-UP MENU (p. 28)D n RETURN (pp. 34, 36, 37, 39)FHDMI (p. 43)
• This function is available for BD-AMS20U only.
G HOME (pp. 23, 34–37, 44)
Introduction
22
Keylock function
You can set the keylock to prevent accidental operations.
This function allows TVs compatible with AQUOS LINK to also perform a Key Lock on the player.
Press and hold (Lock) for more than 3 seconds.
23
•Each time you perform this operation, the function is activated or deactivated.
•If you try to operate the Player while the keylock function is set, “Hold” blinks on the front display panel
to indicate that the keylock function is set.
14
15
24
25
15
Connection
Connecting to a TV/projector
You can enjoy high quality digital picture and sound using an HDMI cable. (Only
TVs/projectors with an HDMI terminal can be connected to this player.)
When you use AQUOS LINK, make sure to use a certified HDMI cable.
1 Be sure to turn off this Player and the TV/projector before making any
connections.
2 Firmly connect an HDMI cable (commercially available) to the HDMI OUT
terminal on the player (1) and the HDMI IN terminal of the TV/projector (2).
HDMI cable
(commercially available)
NOTE
• In this player, “HDMI Video Out” is set to “Auto” as a default (See page 46). (Normally set
to “Auto”.) If you don’t get a stable image with “HDMI Video Out” set to “Auto”, select
the output resolution which corresponds to the connected equipment.
• To enjoy 3D images, connection to a 3D compatible TV is needed.
• For connection to a TV/projector, refer to the TV/projector’s operation manual.
E
After connecting
•If desired, connect audio equipment. (Page 17)
•If necessary, perform the Audio Video Settings. (Pages 46–47)
•Refer to AQUOS LINK function. (Pages 24 and 47)
•Prepare the desired disc or content and start playback. (Pages 26–37, 59)
16
ProjectorTV
Connecting to an amplifier/AV receiver
You can connect this player to an amplifier/AV receiver to enjoy digital surround
sound. With this player, the audio connection can be made using either one of
the following methods depending on the capabilities of the amplifier/AV receiver
you connect.
• HDMI connection
• Digital audio connection
NOTE
• Be sure to turn off this Player and the equipment before making any connections.
• For details on output of audio formats, see page 58.
HDMI connection
HDMI cable
*
NOTE
• When using an HDMI output, 7.1 ch Digital Output is available.
• Audio transmitted in DTS-HD High Resolution Audio and DTS-HD Master Audio
formats is output from the HDMI terminal as Bitstream. Connect an amplifier with a
built-in decoder to enjoy the fine sound quality.
• When a connection to a 3D TV is made via an amplifier/AV receiver, it is necessary to
connect to a 3D compatible amplifier/AV receiver.
If the amplifier/AV receiver is not 3D compatible, connect the HDMI cable to the TV
directly while connecting the player and the amplifier/AV receiver using an optical
digital cable.
Digital audio connection
You can connect an amplifier/AV receiver using an optical digital audio cable
(commercially available).
Optical digital
cable
*
Connection
TV
Commercially available
*
HDMI cable*
Amplifier/
AV receiver
Amplifier/
AV receiver
Commercially available
*
NOTE
• When using OPTICAL DIGITAL AUDIO OUT, 5.1ch Digital Output is available. (7.1ch
Digital Output is not available.)
E
After connecting
•If necessary, perform the Audio Video Settings. (Pages 46–47)
•Prepare the desired disc or content and start playback. (Pages 26–37, 59)
17
Connecting to a USB device
You can connect USB devices to this player (USB memory device, USB HDD) to
enjoy video, music, or picture files stored on the USB device. This player has 2
USB terminals, one on the front side and another on the rear side.
NOTE
• When you insert or remove a USB device, be sure to turn off the main power of this
player and the USB device (only if connecting a USB HDD). Also, be sure to set “Quick
Start” to “No” (See page 47) before inserting or removing the device. If you insert or
remove the device with the player or Quick Start on, the data may become damaged.
• Refer to “Wireless connection (wireless LAN)” on page 20 when connecting a wireless
LAN adapter.
USB memory device connection
Example: Front*
USB memory
device
USB2 terminal
A USB terminal is also available on the rear side (USB1 terminal).
*
USB HDD connection
Example: Front*
1 Connect a USB cable (commercially available) to the USB1 or USB2 terminal
on this player and the USB port of the USB HDD.
2 Turn on the power of the USB HDD.
3 Press POWER to turn on the power of this player.
CAUTION
• SHARP cannot guarantee breakdown or malfunction of a USB HDD, or loss of the
stored data in a USB HDD caused by connecting to other equipment.
NOTE
• Make sure to use a USB device supporting USB 2.0 High Speed (480 Mbps).
• Only self-powered type USB HDD can be used with this player. USB-powered HDD
cannot be used.
• Refer to the operation manual for the USB HDD for details regarding usage.
• This player cannot play back TV programs recorded in a USB HDD by a recorder.
Regarding USB HDD formats
USB HDD is compatible with the following formats:
Formats
FAT32NTFSEXT3
Format
Copy
Delete
Play
4
444
444
444
——
(commercially available)
A USB terminal is also available on the rear side (USB1 terminal).
*
USB cable
18
USB
USB HDD
E
After connecting
•To play back video, music or picture files stored in a USB device, see pages 32–33
and 35–36.
•To initialize data stored in a USB device or delete BD-LIVE data, see page 54.
Broadband Internet Connection
By connecting this player to the Internet, you can enjoy a variety of content
on your TV using BD-LIVE functions, video on-demand services (e-Contents),
home networks and also perform software updates. In this player, the Internet
connection can be made using either one of the following methods.
•Wired connection (LAN cable)
•Wireless connection (wireless LAN) (See page 20.)
NOTE
• Be sure to turn off this Player and the equipment before making any connections.
• When an Internet connection is made, wired and wireless connections cannot be used
at the same time. Use only one of the connection types (See page 50).
CAUTION
• When using a broadband Internet connection, a contract with an Internet service
provider is required. For more details, contact your nearest Internet service provider.
• Refer to the operation manual of the equipment you have as the connected equipment
and connection method may differ depending on your Internet environment.
Wired connection (LAN cable)
Connect a LAN cable (commercially available) to the ETHERNET terminal of this
player (1) and the LAN port of the broadband router (2).
LAN cable
PC
LAN
*
Connection
InternetModemBroadband
router
Commercially available
*
NOTE
• Use a LAN cable/router supporting 10BASE-T/100BASE-TX.
• SHARP cannot guarantee that all brands’ broadband routers will operate with this
player.
E
After connecting
•Perform the communication settings. (Pages 50–53)
•When enjoying BD-LIVE functions, see pages 29 and 48.
•When enjoying video on-demand services (e-Contents), see pages 59–61.
•To play back files via the Home Network, see page 37.
•To update the software via the Internet, perform Software Update Settings.
(Pages 55–56)
19
Broadband Internet Connection
Wireless connection (wireless LAN)
Insert a wireless LAN adapter (Model number VR-WL25, supplied with BDAMS20U only) into the W-LAN/USB1 terminal on the rear of the player.
Wireless LAN
adapter
(supplied with
BD-AMS20U only)
*
NOTE
• When you insert or remove a wireless LAN adapter, be sure to turn the main power off
and make sure that “Quick Start” is set to “No” (See page 47).
• You must use a wireless router/access point that supports IEEE802.11 b/g/n. (n is
recommended for stable operation of the wireless network.)
• Wireless LAN, in its nature, may cause interference, depending on the usage conditions
(access point performance, distance, obstacles, interference by other radio devices,
etc.).
• Set the wireless router/access point to Infrastructure mode. Ad-hoc mode is not
supported.
• SHARP cannot guarantee that wireless LAN adapters other than the VR-WL25 adapter
(supplied with BD-AMS20U only) will operate with this player.
• SHARP cannot guarantee that all brands’ wireless routers will operate with this player.
E
After connecting
•Perform the communication settings. (Pages 50–53)
•When enjoying BD-LIVE functions, see pages 29 and 48.
•When enjoying video on-demand services (e-Contents), see pages 59–61.
•To play back files via the Home Network, see page 37.
•To update the software via the Internet, perform Software Update Settings.
(Pages 55–56)
PCWireless
ModemInternet
router
When a wireless connection is made, it is necessary to enter the MAC address
shown on the wireless LAN adapter for the wireless router. We recommend writing
down the MAC address in this operation manual. (See page 52.)
Optional accessories*
Wireless LAN adapter
(supplied with BD-AMS20U only)
VR-WL25
20
Playback
Before Starting Playback
Loading the Batteries in the Remote
Control
1 Hold in the tab on the battery cover and pull the
cover towards the direction of the arrow.
2 Load the two “AA” size batteries (R-06 size,
UM/SUM-3). Place batteries with their terminals
corresponding to the m and n indications in
battery compartment.
3 Insert the smaller tab of the battery cover into
the opening 1, and press down on the cover
until it clicks in place 2.
NOTE
• Do not subject the remote control unit to shock, water
or excessive humidity.
• The remote control unit may not function if the Player’s
remote sensor is in direct sunlight or any other strong
light.
• Incorrect use of batteries may cause them to leak or
burst. Read the battery warnings and use the batteries
properly.
• Do not mix old and new batteries, or mix different
brands.
• Remove the batteries if you will not use the remote
control unit for an extended period of time.
Approximate operating range of
remote control
Remote control sensor
15º
30º30º
*Approx. 22 feet (7m)
Connecting the Power Cord
Plug the AC cord into AC outlet.
NOTE
• Place the Player close to the AC outlet, and keep the
power plug within reach.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH THE UN-INSULATED PARTS OF ANY CABLES
WHILE THE AC CORD IS CONNECTED.
• The POWER (ON/STANDBY) indicator blinks while the
Player is preparing for starting up. You cannot turn the
Player on until the POWER (ON/STANDBY) indicator
stops blinking.
• If you are not going to use this Player for a long period
of time, be sure to remove the AC cord from the AC
outlet.
Playback
WARNING
• Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater.
This can cause batteries to leak, overheat, explode or
catch fire.
It can also reduce the life or performance of batteries.
15º
Remote control unit
21
Before Starting Playback
Turning the Power On
1 POWER button2 POWER (ON/STANDBY) indicator3 BD/DVD/CD mode indicator4 Front panel display
Turning the power on
Press POWER on the remote control or on the
Indicators on the Player
POWER (ON/STANDBY) indicator
Player to turn on the power of the Player.
Green onPower on
Red onStandby
BD/DVD/CD mode indicator
NOTE
21
• When you turn on this player for the first time after
purchase or when you turn on this player after you
perform “System Reset” (see page 49), the language
setting screen will be displayed, so please perform the
language setting (see step 4 of page 23).
Blue onPlaying back
Blue blinksLoading a disc/updating
About the Home screen
When turning on the player, the Home screen
Entering standby
43
Press POWER on the remote control or on the
appears.
Home screen
Player to enter standby.
• If you press POWER again immediately after entering
standby, the Player may not turn on. If this happens,
wait for 10 seconds or more and then turn on the power
again.
NOTE
• When the POWER (ON/STANDBY) indicator is blinking
(may take some time), the Player cannot be turned on.
Video
1 Main menu2 Submenu3 Button Guide
MusicPicturee-ContentsSettings
BD-VIDEOUSB-1USB-2Home Network
Next
22
Loading...
+ 56 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.