Page 1
EN-1
ENGLISH
SPLIT TYPE
ROOM AIR CONDITIONER
OPERATION MANUAL
INDOOR UNIT OUTDOOR UNIT
AH-PNX11 AU-PNX11
AH-PNX14 AU-PNX14
Device of this mark is a
trademark of Sharp Corporation.
Plasmacluster is a registered
trademark or a trademark of
Sharp Corporation.
AH-PNX11_EN.indd 1 11.3.17 4:02:12 PM
Page 2
EN-2
AH-PNX11_EN.indd 2 11.3.17 4:02:12 PM
Page 3
EN-1
ENGLISH
Please read this manual carefully before using
the product. This manual should be kept in a
safe place for handy reference.
ENGLISH
CONTENTS
• IMPORTANT SAFETY INSTRUCTIONS .....EN-1
• PART NAMES ..............................................EN-2
• USING THE REMOTE CONTROL ..............
EN-4
• AUXILIARY MODE ......................................
EN-4
• TIPS ON SAVING ENERGY ........................EN-4
• BASIC OPERATION ....................................EN-5
•
ADJUSTING THE AIR FLOW DIRECTION
........EN-6
• SUPER JET OPERATION ...................EN-6
• GENTLE COOL AIR ....................................
EN-7
• PLASMACLUSTER OPERATION ...............
EN-7
• LAUNDRY OPERATION ..............................
EN-8
• TIMER OPERATION
....................................EN-9
• INSTANT LOW WATTAGE OPERATION ....EN-10
• SELF CLEAN OPERATION .........................EN-10
• MAINTENANCE ..........................................EN-11
• BEFORE CALLING FOR SERVICE ............EN-12
• OPERATING CONDITION
...........................EN-12
IMPORTANT SAFETY
INSTRUCTIONS
WARNINGS
• Do not pull or deform the power supply cord.
Pulling and misuse of the power supply cord
can result in damage to the unit and cause
electrical shock.
• Be careful not to expose your body directly to
the outlet air for a long time. It may affect your
physical conditions.
• When using the air conditioner for infants,
children, elderly, bedridden, or disabled people
make sure the room temperature is suitable for
those in the room.
• Never insert objects into the unit. Inserting
objects can result in injury due to the high
speed rotation of internal fans.
• Ground the air conditioner without fail. Do not
connect the grounding wire to gas pipe, water
pipe, lightning rod or telephone grounding
wire. Incomplete grounding may cause electric
shock.
• If anything is abnormal with the air conditioner
(ex. a burning smell), stop the operation
immediately and turn the circuit breaker OFF.
• The appliance shall be installed in accordance
with national wiring regulations. Improper
cable connection can cause the power supply
cord, plug and the electrical outlet to overheat
and cause fire.
• If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similarly qualified person in order
to avoid a hazard. Use only the manufacture-
specified power cord for replacement.
• Do not splash or pour water directly on the
unit. Water can cause electrical shock or
equipment damage.
• Do not attempt to install/remove/repair the unit
by yourself. Incorrect work will cause electric
shock, water leak, fire etc. Consult your dealer
or other qualified service personnel for the
installation/removal/repair of the unit.
CAUTIONS
• Open a window or door periodically to
ventilate the room, especially when using gas
appliances. Insufficient ventilation may cause
oxygen shortage.
• Do not operate the buttons with wet hand. It
may cause electric shock.
• For safety, turn the circuit breaker off when not
using the unit for an extended period of time.
• Check the outdoor unit mounting rack
periodically for wear and to make sure it is
firmly in place.
• Do not put anything on the outdoor unit nor
step on it. The object or the person may fall
down or drop, causing injury.
• This unit is designed for residential use. Do
not use for other applications such as in a
kennel or greenhouse to raise animals or grow
plants.
• Do not place a vessel with water on the unit.
If water penetrates into the unit, electrical
insulations may deteriorate and cause electric
shock.
• Do not block the air inlets nor outlets of the
unit. It may cause insufficient performance or
troubles.
• Be sure to stop the operation and turn the
circuit breaker off before performing any
maintenance or cleaning. A fan is rotating
inside the unit and you may get injured.
• This appliance is not intended for use by
young children or infirm persons without
supervision. Young children should be
supervised to ensure that they do not play with
the appliance.
• Make sure to connect the air conditioner to
power supply of the rated voltage and frequency. Use of a power supply with improper
voltage and frequency can result in equipment
damage and possible fire.
• Do not install the unit in a place where inflammable gas may leak. It may cause fire.
Install the unit in a place with minimal dust,
fumes and moisture in the air.
• Arrange the drain hose to ensure smooth
drainage. Insufficient drainage may cause wetting of the room, furniture etc.
• Make sure a leak breaker or a circuit breaker
is installed, depending on the installation location, to avoid electrical shock.
AH-PNX11_EN.indd 1 11.3.17 4:02:12 PM
........
Page 4
EN-2
1 Inlet (Air)
2 Open Panel
3 Air Filter
4 AUX Button
5 Receiver Window
6 Power Supply Cord
7 Vertical Airflow Louvre
8 Horizontal Airflow Louvre
9 Outlet (Air)
10 INSTANT LO W WATTA G E
Lamp (red / green
)
11 PLASMACLUSTER Lamp
(blue
)
12 OPERATION Lamp (red
)
13 TIMER Lamp (orange
)
14 SUPER JET Lamp
(green
)
15 LAUNDRY Lamp (red
)
16 Inlet (Air)
17 Refrigerant Pipe and
Interconnecting Cord
18 Drainage Hose
19 Outlet (Air)
NOTE:
Actual units might vary slightly
from those shown above.
OUTDOOR UNIT
1
2
3
4
5
6
7
8
9
PART NAMES
INDOOR UNIT
AH-PNX11AH-PNX14
AH-PNX11_EN.indd 2 11.3.17 4:02:13 PM
10
11
12
13
14
15
10
11
12
13
14
15
16
18
19
17
Page 5
EN-3
ENGLISH
REMOTE CONTROL
1 TRANSMITTER
2 DISPLAY
3 ON/OFF Button
4 THERMOSTAT Button
5 INSTANT LOW WATTAGE Button
6 LAUNDRY Button
7 PLASMACLUSTER Button
8 TIMER ON Button
9 MODE Button
10 TIMER OFF Button - SLEEP MODE
11 FAN Button
12 TIMER CANCEL Button
13 SWING Button
14 RESET Button
15 SUPER JET Button
16 SELF CLEAN Button
17 GENTLE COOL AIR Button
DISPLAY
18
19
20
21
22
23
24
25
26
27
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18 MODE Symbols
: AUTO : COOL : DRY
19 SUPER JET Symbol
20 SELF CLEAN Symbol
21 PLASMACLUSTER Symbol
22 FAN SPEED Symbols
: AUTO
: Manual setting
23
GENTLE COOL AIR Symbol
24 TEMPERATURE AND TIMER COUNT
DOWN Indicator
25 LAUNDRY Symbol
26 TRANSMITTING Symbol
27 TIMER ON / TIMER OFF Indicator
AH-PNX11_EN.indd 3 11.3.17 4:02:14 PM
Page 6
EN-4
LOADING BATTERIES
1
Remove the battery cover.
2
Insert two batteries.
(AAA(R03))
Make sure the (+) and (-) polarities are correctly aligned.
3
Reinstall the battery cover.
4
Press the RESET button using a
thin stick.
NOTE:
• The battery life is approximately 1 year in
normal use.
• When replacing the batteries, always change
both and use the same type.
• If you will not be using the unit for a long time,
remove the batteries from the remote control.
USING THE REMOTE CONTROL
Battery cover
HOW TO USE THE REMOTE CONTROL
Point the remote control towards the receiver
window and press the desired button. The
unit generates a beep when it receives the
signal.
• Make sure nothing, such as curtains, block the
signal receiver window.
• The signal effective distance is 7 m.
CAUTION:
•
Do not expose the receiver window to direct
sunlight. This may adversely affect its operation.
•
Use of certain fluorescent lamp in the same room
may interfere with transmission of the signal.
• Do not leave the remote control in direct
sunlight or near a heater. Protect the remote
control from moisture and shock.
Use this mode when the remote control is
not available.
TO TURN ON
Press the AUX button.
•
The red OPERATION lamp ( ) will light and
the unit will start operating in the AUTO mode.
• The fan speed and temperature setting are
set to AUTO.
TO TURN OFF
Press the AUX button again.
• The red OPERATION lamp ( ) will turn off.
AUX
AUXILIARY MODE
TIPS ON SAVING ENERGY
Below are some simple ways to save energy
when you use your air conditioner.
Set the proper temperature
• Setting the temperature lower than necessary during cooling operation will result in
increased power consumption.
Block direct sunlight and prevent drafts
•
Blocking direct sunlight during cooling operation
will reduce power consumption.
• Close the windows and doors during cooling
operation.
Keep filter clean to ensure the most ef-
ficient operation
Disconnect the power cord when the
unit is not used for an extended period
of time
• The indoor unit still consumes a small amount
of power when it is not operating.
7 m
Receiver window
RESET button
AH-PNX11_EN.indd 4 11.3.17 4:02:14 PM
AUX
Page 7
EN-5
ENGLISH
1
Press the MODE button to select the
operation mode.
2
Press the ON/OFF button to start
operation.
• The red OPERATION lamp ( ) will light up.
TO TURN OFF
Press the ON/OFF button again.
• The red OPERATION lamp ( ) will turn off.
3
Press the THERMOSTAT button to
set the desired temperature.
(AUTO/DRY mode)
The temperature can be
changed up to ±2 °C the
automatically set of temperature.
(COOL mode)
The temperature setting
range:
16-30°C.
4
Press the FAN button to set the
desired fan speed.
2
3
1
4
BASIC OPERATION
AUTO COOL DRY
AUTO SOFT LOW HIGH
NOTE:
AUTO MODE
In the AUTO mode, the temperature setting and mode are automatically selected according to the
room temperature when the unit is turned on.
DRY MODE
The fan speed is preset to AUTO and cannot be changed.
WHEN POWER FAILURE OCCURS
This air conditioner has a memory function to store settings when a power failure occurs.
After power recovery, the unit will automatically re-start in the same settings which were active before
the power failure, except for timer settings.
AH-PNX11_EN.indd 5 11.3.17 4:02:14 PM
Page 8
EN-6
HORIZONTAL AIR FLOW DIRECTION
Hold the horizontal airflow louvre levers and adjust the air flow direction.
CAUTION:
Never attempt to adjust the vertical airflow louvre manually.
• Manual adjustment of the vertical airflow lou-
vre can cause the unit to malfunction.
• When the vertical adjustment louvre is posi-
tioned at the lowest position in the COOL or
DRY mode for an extended period of time,
condensation may res
ult.
VERTICAL AIR FLOW DIRECTION
1
Press the SWING button.
• The vertical airflow louvre will swing.
2
Press the SWING button again
to stop the desired position.
• The adjustment range is narrower the
swing range in order to prevent condensation from dripping.
ADJUSTING THE AIR FLOW
DIRECTION
1
2
Louvre levers
The air conditioner works at the maximum
power and optimum louvre direction to
makes the room cool rapidly.
1
During operation, press the
SUPER JET button.
• The remote control will display “ ”.
• The temperature display will go off.
• The green SUPER JET lamp (
)
will light up.
• The vertical airflow louvre will be set
obliquely downward.
TO CANCEL
Press the SUPER JET button
again.
• The green SUPER JET lamp ( )
will turn off.
• The vertical airflow louvre will return to
the original direction.
NOTE:
• The air conditioner will operate at “Extra
HIGH” fan speed for 15 minutes, and then
shift to “HIGH” fan speed.
• You can not set the temperature or fan speed
during the SUPER JET operation.
1
SUPER JET OPERATION
AH-PNX11_EN.indd 6 11.3.17 4:02:15 PM
Page 9
EN-7
ENGLISH
The vertical airflow louvre is set obliquely
upward to deliver cool air to the ceiling in
order to avoid direct airflow.
1
During operation, press the
GENTLE COOL AIR button.
• The remote control will display “ ”.
TO CANCEL
Press the GENTLE COOL AIR button
again.
NOTE:
•
If you want GENTLE COOL AIR operation in
SUPER JET mode, press GENTLE COOL
AIR button during SUPER JET operation.
1
GENTLE COOL AIR
PLASMACLUSTER OPERATION
Plasmacluster ions released into the room
will reduce some airborne mold.
1
During operation, press the
PLASMACLUSTER button.
• The remote control will display “ ”.
• The blue PLASMACLUSTER lamp (
)
will light up.
TO CANCEL
Press the PLASMACLUSTER button
again.
• The blue PLASMACLUSTER lamp ( )
will turn off.
NOTE:
• Use of the PLASMACLUSTER operation will
be memorized, and it will be activated the next
time you turn on the unit.
• To perform Plasmacluster operation in FAN
only mode, press the PLASMACLUSTER button when the unit is not operating.
The mode symbol of the remote control will go
off and the fan speed cannot be set to AUTO.
1
AH-PNX11_EN.indd 7 11.3.17 4:02:15 PM
Page 10
EN-8
1
STOP
LAUNDRY OPERATION
When you want to quickly dry clothes.
1
Press the LAUNDRY button.
• The remote control will displays “ ”.
•
The blue PLASMACLUSTER lamp ( ),
the red LAUNDRY lamp (
) and the red
OPERATION lamp ( ) will light up.
2
Press the SWING button and
select the swing range so that
air from the unit is blown to the
clothes.
• The swing range can be selected in 7 pat-
terns.
TO STOP
Press the ON/OFF Button.
Alternatively, press the LAUNDRY but-
ton.
•
The blue PLASMACLUSTER lamp( ),
the red LAUNDRY lamp ( ) and the red
OPERATION lamp ( ) will turn off.
NOTE:
Up to 1
hour
Operate in Fan only mode at high
speed to dry clothes.
1 hour
to 5
hour
Operate in dry mode at low or
soft fan speed to dry room and
reduce odors of clothes with
Plasmacluster ions.
After 5
hours
Operate in fan only mode at soft
fan speed to circulate air.
• You can not set the temperature, fan speed or
the TIMER ON during the LAUNDRY operation.
• Depending on the volume and material of
clothes, the clothes may not be dry thoroughly.
• You can extend laundry operation in cooling
and dry mode using the TIMER OFF(
).
• The clothes may not dry thoroughly when
the unit set to the INSTANT LOW WATTAGE
mode.
2
AH-PNX11_EN.indd 8 11.3.17 4:02:15 PM
fan
Page 11
EN-9
ENGLISH
TIMER ON
1
Press the TIMER ON button and
set the time as desired.
•
The orange TIMER lamp ( ) will light
up.
• The time setting will count down to show
the remaining time.
TO CANCEL
Press the CANCEL button.
•
The orange TIMER lamp ( ) will turn
off.
TIMER OPERATION
1
TIMER OFF - SLEEP MODE
1
Press the TIMER OFF button
and set the time as desired.
•
The orange TIMER lamp ( ) will light
up.
• The time setting will count down to show
the remaining time.
TO CANCEL
Press the CANCEL button.
• The orange TIMER lamp ( ) will turn
off.
CANCEL
1
NOTE:
• Timer duration can be set from a minimum half an hour to a maximum of 12 hours. Up to 9.5 hours,
you can set in half-hour increments, and from 10 to 12 hours, in 1-hour increments.
• The TIMER OFF and TIMER ON can not be set together.
• The LAUNDRY operation has priority over the TIMER ON operation.
• When the temperature is set during timer setting, the temperature will show in the display for 5 sec
-
onds and then return to the timer display.
• If a power failure occurs while the TIMER is set, the TIMER setting will be cancelled and will not be
retrieved even after the power is restored.
TIMER OFF - SLEEP MODE
• When the TIMER OFF is set, the unit automatically adjusts the temperature setting to prevent
excessive cooling while you are in sleep. One hour after the TIMER OFF is set, the unit gradually
raises the temperature setting by 1°C by repeated ON/OFF operation for your comfortable sleep.
TIMER ON
• The unit will turn on prior to the set time to allow the room to reach the desired temperature by the
programmed time. (Awaking function)
CANCEL
AH-PNX11_EN.indd 9 11.3.17 4:02:16 PM
Page 12
EN-10
INSTANT LOW WATTAGE
OPERATION
The air conditioner will operate with reduced
maximum power and excess power consumption will be avoided.
1
During operation, press the
INSTANT LOW WATTAGE
button to select desired maximum wattage.
• The INSTANT LOW WATTAGE lamp
(
) will light up as follows.
(AH-PNX11)
Maximum wattage 600W 400W Free
Lamp (
)
Red Green OFF
(AH-PNX14)
Maximum wattage 800W 600W Free
Lamp (
)
Red Green OFF
NOTE:
• The unit memorizes the previous INSTANT
LOW WATTAGE setting and will be activated
the next time operated.
• INSTANT LOW WATTAGE operation can not
be available when the unit is in PLASMACLUSTER operation at FAN mode and SELF
CLEAN operation.
1
SELF CLEAN OPERATION
SELF CLEAN operation will reduce the
growth mold fungus with Plasmacluster
ions and dry inside of the unit. Utilize the
operation at seasonal change over terms or
every 4 months.
1
Press the SELF CLEAN button
when the unit is not operating.
• The remote control will display “ ”.
• The blue PLASMACLUSTER lamp (
)
will light up.
•
The unit will stop operation after 40 minutes.
TO CANCEL
Press the SELF CLEAN button.
• The blue PLASMACLUSTER lamp ( )
will turn off.
NOTE:
• You cannot set the temperature, fan speed, air
flow direction or timer setting during the SELF
CLEAN operation.
• Mold fungus already grown can not be
eliminated by this operation.
1
AH-PNX11_EN.indd 10 11.3.17 4:02:16 PM
Page 13
EN-11
ENGLISH
Be sure to disconnect the power cord from
the wall outlet or turn off the circuit breaker
before performing any maintenance.
CLEANING THE FILTERS
1
Turn off the unit.
2
Remove the filters.
1 Lift the open panel.
2
Pull the air filters down to remove them.
3
Clean the filters.
• Use a vacuum cleaner to remove dust. If
the filters are dirty, wash them with warm
water and a mild detergent. Dry filters in
the shade before reinstalling.
4
Reinstall the filters and close
the open panel.
CLEANING THE UNIT AND THE REMOTE CONTROL
• Wipe them with a soft cloth.
• Do not directly splash or pour water on them.
It can cause electrical shock or equipment
damage.
• Do not use hot water, thinner, abrasive pow-
ders or strong solvents.
MAINTENANCE
MAINTENANCE AFTER AIR CONDITIONER SEASON
1
Operate the unit in the SELF
CLEAN operation to thoroughly
dry inside the unit.
2
Stop the operation and unplug
the unit.
• Turn off the circuit breaker, if you have
one exclusively for the air conditioner.
3
Clean the filters, then reinstall
them.
MAINTENANCE BEFORE AIR CONDITIONER SEASON
1
Make sure that the air filters are
not dirty.
2
Make sure that nothing obstructs the air inlet or outlet.
AH-PNX11_EN.indd 11 11.3.17 4:02:16 PM
Page 14
EN-12
Check the following points before calling for
service.
The unit does not operate
• Check if the circuit breaker has tripped or the
fuse has blown.
The unit does not cool effectively
• Check the filters. If dirty, clean them.
• Check the outdoor unit to make sure nothing
is blocking the air inlet or outlet.
• Check the thermostat is proper setting.
• Make sure windows and doors are closed
tightly.
The unit does not receive the remote
control signal
• Check whether the remote control batteries
have become old and weak.
• Try to send the signal again with the remote
control pointed properly towards the unit’s
signal receiver window.
• Check whether the remote
control batteries
are installed properly.
Please call for service when OPERATION
lamp and TIMER lamp on the unit blink.
BEFORE CALLING FOR SERVICE
The following conditions do not denote
equipment malfunctions
UNIT DOES NOT OPERATE
The unit will not operate if it is turned on immediately after it is turned off. The unit will
not operate immediately after the mode is
changed. This is to protect the unit. Wait 3 minutes before operating the unit.
ODORS
Carpet and furniture odors that entered into the
unit may be sent out from the unit.
CRACKING NOISE
This sound is generated by the friction of the
unit expanding or connecting due to a temperature change.
A LOW BUZZING NOISE
This is a sound of the unit generating Plasmacluster ions.
SWISHING NOISE
The soft, swishing noise is the sound of the
refrigerant flowing inside the unit.
MIST SEEN AT INDOOR AIR OUTLET
In cooling operation, this is caused by the difference between the room air temperature and
the air discharged.
THE OUTDOOR UNIT DOES NOT STOP
After stopping the operation, the outdoor unit
will rotate its' fan for about a minute to cool
down the unit.
ODOR EMITTED FROM THE
PLASMACLUSTER AIR OUTLET
This is the smell of ozone generated from
the Plasmacluster Ion generator. The ozone
concentration is very small, posing no adverse
effect on your health. The ozone discharged
into the air rapidly decomposes, and its density
in the room will not increase.
OPERATING CONDITION
Mode
Indoor
Temp.
Outdoor
Temp.
Cooling
Upper limit 32˚C 43˚C
Lower limit 21˚C 21˚C
• The built-in safety device may prevent the unit
from operating when used out of this range.
• Condensation may form on the air outlet if the
unit operates continuously in the COOL or
DRY mode when humidity is over 80 %.
AH-PNX11_EN.indd 12 11.3.17 4:02:17 PM
Page 15
IN-13
INDONESIA
AH-PNX11_ID.indd 13 11.3.17 4:07:28 PM
Page 16
IN-14
Printed in Thailand
TINSEA733JBRZ 11L- 1
SHARP CORPORATION
AH-PNX11_ID.indd 14 11.3.17 4:07:28 PM
Loading...