Sharp AR-M550N, AR-M550U, AR-M620N, AR-M620U, AR-M700N Service Manual

...

SERVICE MANUAL

CODE: 00ZAR700//F1E

DIGITAL LASER COPIER/PRINTER DIGITAL MULTIFUNCTIONAL SYSTEM

AR-M550N/M550U AR-M620N/M620U

MODEL

[1] OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[2] CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

[3] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

[4] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

[5] EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . . . 5-1

[6] DETAILS OF EACH SECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[7] SETTING AND ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[8] SIMULATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

[9] SELF DIAG MESSAGE AND TROUBLESHOOTING . . . . . . . . . . 9-1

[10] ROM VERSION-UP METHOD . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

[11] MAINTENANCE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

AR-M700N/M700U

CONTENTS

[12] OTHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

[13] ELECTRIC DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

[14] SIGNAL NAME LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION

for after sales service only. The contents are subject to change without notice.

CAUTION

This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achieved on the eye’s retina, there is the danger of spot damage to the retina.

The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time of servicing.

1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as a unit, not as individual parts.

2) Do not look into the machine with the main switch turned on after removing the developer unit, toner cartridge, and drum cartridge.

3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connected when removing and installing the optical system.

4) The middle frame contains the safety interlock switch.

Do not defeat the safety interlock by inserting wedges or other items into the switch slot.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

Wave length: 785 nm Pulse times

North America: 55 cpm model (3.1 µs

Europe: 55 cpm model (3.7 µs

Output power: Max 0.8 mW

Laserstrahl

+10 nm –15 nm

62 cpm model (3.1 µs 70 cpm model (2.7 µs

62 cpm model (3.7 µs 70 cpm model (3.2 µs

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

CAUTION

UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.

VORSICHT

USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.

ADVARSEL

USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.

ADVERSEL

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.

VARNING

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VAR O!

± 3.1 ns)/7 mm ± 3.1 ns)/7 mm ± 2.7 ns)/7 mm ± 3.7 ns)/7 mm ± 3.7 ns)/7 mm ± 3.2 ns)/7 mm

CAUTION

INVISIBLE LASER RADIATION,

WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

VORSICHT

UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.

VARO !

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN.

ADVARSEL

USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.

VARNING !

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN. – STRÅLEN ÄR FARLIG.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

CONTENTS

[1] OUTLINE

1. Main Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

A. High reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

B. Network tandem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

C. 2-Way Security Solution . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

D. Document Filing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

[2] CONFIGURATION

1. Main unit and option lineup. . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

2. Block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

[3] SPECIFICATIONS

1. Basic specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

A. Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

2. Engine specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

A. Paper feeding, paper conveyance,

and discharge section . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

B. Scanner section (read) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

C. Scanner section (write) . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

D. Image processing section . . . . . . . . . . . . . . . . . . . . . . . . 3-4

E. Fuser section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

F. Drive section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

3. Operating specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

A. Common operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

B. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

C. Image send function . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

D. Printer function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11

E. Document filing function . . . . . . . . . . . . . . . . . . . . . . . . 3-14

4. Safety and environmental protection standards . . . . . . . . . 3-15

A. Safety standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

B. Environmental standards. . . . . . . . . . . . . . . . . . . . . . . . 3-15

5. Ambient conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

A. Space required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

B. Operating ambient conditions . . . . . . . . . . . . . . . . . . . . 3-15

C. Ambient storage conditions . . . . . . . . . . . . . . . . . . . . . . 3-15

D. Ambient conditions for transporting. . . . . . . . . . . . . . . . 3-16

E. Standard temperature and humidity . . . . . . . . . . . . . . . 3-16

6. Service related items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

[4] CONSUMABLE PARTS

1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

A. USA, Canada, South and Central America . . . . . . . . . . . 4-1

B. Europe affiliates (Including East Europe, Russia)/

Australia/New Zealand/UK) . . . . . . . . . . . . . . . . . . . . . . . 4-1

C. Asia affiliates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

D. Hong Kong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

E. China (AR-M620N/M700N) . . . . . . . . . . . . . . . . . . . . . . . 4-1

F. Middle East/Philippine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

G. Taiwan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

2. Maintenance parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

A. USA, Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

B. Europe affiliates (Including East Europe, Russia)

Australia/New Zealand/UK . . . . . . . . . . . . . . . . . . . . . . . 4-3

C. Middle East/Asia/South and Central America . . . . . . . . . 4-4

D. China. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

E. Taiwan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

[5] EXTERNAL VIEW AND INTERNAL STRUCTURE

1. External view and operation parts . . . . . . . . . . . . . . . . . . . . 5-1

A. External view and external operation parts. . . . . . . . . . . 5-1

B. Internal operation parts . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

C. Operation, display parts . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

D. Job status screen (common to print, copy,

network scan and internet fax) . . . . . . . . . . . . . . . . . . . . 5-4

2. Function parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

A. Sensor/detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

B. Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

C. Clutch/solenoid. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

D. Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

E. Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14

F. Fan motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15

G. PWB (Main unit section) . . . . . . . . . . . . . . . . . . . . . . . . 5-16

H. FAX section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17

I. Fuse/thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18

J. Adjustment volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19

K. Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

L. Heater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20

M. Lock position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21

N. Roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22

O. Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24

[6] DETAILS OF EACH SECTION

1. Operation panel section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

A. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

B. Major parts and signal functions . . . . . . . . . . . . . . . . . . . 6-2

C. Maintenance and parts replacement. . . . . . . . . . . . . . . . 6-3

2. Paper feed, paper transport, duplex,

and paper exit reverse sections . . . . . . . . . . . . . . . . . . . . . . 6-5

[Paper feed section] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

(Manual paper feed section) . . . . . . . . . . . . . . . . . . . . . . 6-6

(Paper feed tray sections 1 and 2) . . . . . . . . . . . . . . . . 6-13

(Paper feed trays 3 and 4) . . . . . . . . . . . . . . . . . . . . . . 6-20

[Paper Transport Section] . . . . . . . . . . . . . . . . . . . . . . . . . 6-30

(Vertical paper transport section 1). . . . . . . . . . . . . . . . 6-30

(Vertical paper transport section 2). . . . . . . . . . . . . . . . 6-34

(Horizontal transport section) . . . . . . . . . . . . . . . . . . . . 6-39

[Paper exit and turning section] . . . . . . . . . . . . . . . . . . . . . 6-44

(Duplex section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-49

3. Laser scan unit (LSU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-60

4. Image process section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-63

[Toner hopper and toner bottle section] . . . . . . . . . . . . . . . 6-64

[Developer tank section]. . . . . . . . . . . . . . . . . . . . . . . . . . . 6-69

[OPC drum section] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-74

[Transfer section] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-82

[Main charger section] . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-87

5. Scanner section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-89

6. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-101

7. SPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-113

[External outfit section]. . . . . . . . . . . . . . . . . . . . . . . . . . . 6-114

[Paper feed tray section] . . . . . . . . . . . . . . . . . . . . . . . . . 6-116

[Paper feed/transport section] . . . . . . . . . . . . . . . . . . . . . 6-119

[CIS section]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-125

[Paper exit section]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-127

[Other] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-131

8. Drive section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-133

9. Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-146

10.PWB section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-147

11.Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-151

12.Fan motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-153

13.Sensors and switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-158

[7] SETTING AND ADJUSTMENTS

[ADJ 1] Adjusting high voltage values. . . . . . . . . . . . . . . . . . . 7-2

[ADJ 2] Adjusting the developing unit . . . . . . . . . . . . . . . . . . . 7-6

[ADJ 3] Adjusting image distortions. . . . . . . . . . . . . . . . . . . . . 7-7

[ADJ 4] Adjusting the SPF parallelism. . . . . . . . . . . . . . . . . . 7-12

[ADJ 5] Adjusting the image focus . . . . . . . . . . . . . . . . . . . . 7-14

[ADJ 6] Adjusting the image magnification . . . . . . . . . . . . . . 7-16

[ADJ 7] Adjusting the image off-center . . . . . . . . . . . . . . . . . 7-21

[ADJ 8] Adjusting the image position, image loss,

and void area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

[ADJ 9] Adjusting the copied image quality. . . . . . . . . . . . . . 7-30

[ADJ 10] Adjusting the print quality in fax mode . . . . . . . . . . . 7-33

[ADJ 11] Adjusting the image quality in scan mode . . . . . . . . 7-36

[ADJ 12 Common image quality adjustments for all of copy,

scan, and fax modes . . . . . . . . . . . . . . . . . . . . . . . . 7-38

[ADJ 13] Adjusting the fusing paper guide position. . . . . . . . . 7-39

[ADJ 14] Adjusting the paper size detection . . . . . . . . . . . . . . 7-40

[ADJ 15] Adjusting the original size detection

(in original table mode). . . . . . . . . . . . . . . . . . . . . . . 7-42

[ADJ 16] Adjusting the touch panel coordinates . . . . . . . . . . . 7-43

[ADJ 17] Adjusting the supply voltage. . . . . . . . . . . . . . . . . . . 7-43

[8] SIMULATION

1. Adjustment value/Simulation and storage data . . . . . . . . . . 8-1

A. Simulation adjustment value/Set value data . . . . . . . . . . 8-1

B. Each storage data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

2. Outline and purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

3. Code-type simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

A. Operating procedures and operations. . . . . . . . . . . . . . . 8-6

B. Simulation list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8

C. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20

[9] SELF DIAG MESSAGE AND TROUBLESHOOTING

[Error code] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

2. Function and purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

3. Self diag message kinds. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

4. Self diag operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

A. Self diag operation and related work flow . . . . . . . . . . . . 9-1

5. Breakdown sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

A. Breakdown mode process . . . . . . . . . . . . . . . . . . . . . . . . 9-2

B. Power ON trouble detection sequence.. . . . . . . . . . . . . . 9-3

6. Communication in trouble . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

A. FAX call request/call-in specifications . . . . . . . . . . . . . . . 9-4

7. Trouble kind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

8. Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7

[10] ROM VERSION-UP METHOD

1. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

A. Version-up target ROM's . . . . . . . . . . . . . . . . . . . . . . . 10-1

B. ROM version-up is required in the following cases: . . . 10-1

2. Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

A. Relationship between each ROM and version-up. . . . . 10-2

3. Necessary items for Flash ROM version-up. . . . . . . . . . . . 10-2

4. Flash ROM version-up method . . . . . . . . . . . . . . . . . . . . . 10-2

A. MFP control PWB ROM DIP switch selection

and Flash ROM slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

B. Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

C. Version-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . 10-13

D. Version-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . 10-23

E. Countermeasures against "Result: NG" . . . . . . . . . . . . 10-4

5. Turning OFF the power during the version-up procedure . 10-5

6. Version-up procedure flowchart . . . . . . . . . . . . . . . . . . . . . 10-5

[11] MAINTENANCE LIST

1. Maintenance list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1

2. Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

A. Drum peripheral section . . . . . . . . . . . . . . . . . . . . . . . . 11-4

B. Transfer section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5

C. Developing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6

D. Fusing section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7

E. Scanner section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9

F. SPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10

G. Paper feed section . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-11

H. Transport section/paper exit reverse section/

duplex section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12

I. Drive section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13

J. Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-14

3. Maintenance and disassembly. . . . . . . . . . . . . . . . . . . . . 11-15

A. Necessary execution items in maintenance

and servicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-15

[12] OTHER

1. VARIOUS COUNTERS SPECIFICATIONS. . . . . . . . . . . . 12-1

A. Count specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

B. Location and display of each counter data . . . . . . . . . . 12-5

2. Web setting service mode . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

A. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

B. Operating procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

C. Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7

3. Paper jam code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9

A. Paper jam judgment conditions. . . . . . . . . . . . . . . . . . . 12-9

B. Inserter (AR-CF2) paper jam judgment conditions . . . 12-13 C. Finisher (AR-F15/F16) paper jam judgment

conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14

[13] ELECTRIC DIAGRAM

1. Overall block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1

2. Power line chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2

3. Actual wiring chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

A. Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-5

4. Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-13

[14] SIGNAL NAME LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1

[1] OUTLINE

1. Main Features

(1) Single Pass Duplex Scanner

• Max. 76 cpm for duplex scanning

• Best-in-class 150-sheet feeder

(2) Security Solution

Data encryption + data clear with random number

• Network security

(3) New Toner

• Higher density/Finer particles

(4) Inner Output

• Separate copy output pages from printer output pages

(5) Enhance the solutions such as document filing and

other features.

(6) Design for High Reliability

• Robust frame designed by highly accurate CAE analysis

(7) Improved Performance

• Network Tandem Copy/Print

• High-speed Processor

• New high-speed ASIC

(8) Fax feature

For replacement of mid/low speed devices (up to area)

(9) Large Capacity Finisher

Finisher capacity: 4,000-sheet

2. Features

(2) Strengthened Frame Structure

Highly Rigid Frame

Improved stability with less machine distortion, and both rigidity and lightweight been achieved.

(3) Energy Saving with Unique External Heat Roller

Fusing System

Newly Developed External Heating System

1) High reliability with stabilized fusing ability

2) Shortened warm up time before start copying

3) Achievement of energy efficiency that clears 2006 Rationalization in Energy Use Law

External Heat Roller Fusing System

Thin Steel Fusing Roller

Low Heat Capacity Rubber Roller

High Efficiency Heater

External Heating Roller

B. Network tandem

With Network tandem function, users can output one job on two network connected engines. Productivity of large-volume copying/printing can be dramatically improved by high-speed output of up to 110cpm (55cpm model), 124cpm (62cpm model) and 140cpm (70cpm model)

Scan original from

Copy

document glass or DSPF

A. High reliability

(1) Improved Image Quality/Paper Transport

Full-Grip Path Design

Stable paper feeding realized by rollers that firmly grip paper

Small-Diameter Belt Transfer System

With reduced effect to paper types, drum paper release is stabilized and transfer efficiency is improved

Easier Paper Jam Fixation with Open Paper Path

Jammed paper on vertical paper path can be easily removed by opening the left side cover, which shortens time to fix paper jam

Send print data from PC

NOTE: Users can use the function simply by connecting the engines

AR-M550/M620/M700 OUTLINE 1 - 1

to network. This means no Tandem Kit (Connection cable) necessary. For N model, only optional Printer Expansion Kit is required.

C. 2-Way Security Solution

aEncrypted data

ONLY-ONE

Print data

Way-in : Network Security

Allow access of authorized network address only and prevent unauthorized access from outside. (Filtering of network address)

(1) Data Security coexisting with Document Filing

Document Filing/Quick File

•

Original data

•

Print data

•

Fax data

Store Store

Store

HDD memoryHDD memory

Raw/compressed dataRaw/compressed dataRaw/compressed data

Recall (Job settings)Recall (Job settings)

•

PIN printing

•

Password input

Install DSKInstall DSK

Copy data

Print data

Scan data

Fax data

Way-out : HDD Data Clear + Encryption

Data clear by plural writing random number. Cannot be analyzed even when peeped by encryption.

Data SecurityData Security

Document Filing/Quick File

•

Original data

•

Print data

•

Fax data

•

PIN printing

•

Password input

Encrypt before storing

Encrypt before storingEncrypt before storing

Recall (Job settings)

HDD memory

Encrypted dat

Security is assured by encrypting the data to be stored!

AR-M550/M620/M700 OUTLINE 1 - 2

D. Document Filing

Document filing is a function that enables users to share and reuse data stored in the engine’s HDD by digitalizing various information sent/scanned from printer, fax, PC or MFP that are connected by network.

PC Fax PC i-Fax

Print data

PC-Fax is like printing Word data etc. onto fax paper.

G3 Fax

Fax data

Copy

HDD

AR-M550N/U

AR-M550N/U AR-M620N/U

AR-M620N/U

i-Fax data

Internet-Fax

Scan

FAX

i-FAX

Telephone line Network/LAN

Send E-mail

Send

Send E-mail

<List of data stored in Main folder

G3 Fax

Internet Fax

AR-M550/M620/M700 OUTLINE 1 - 3

: Feb. 9 2004

[2] CONFIGURATION

1. Main unit and option lineup

(1) Main unit lineup

Model name Composition

AR-M550U/M620U/M700U Copier model

AR-M550N/M620N/M700N Network printer model

(2) Option lineup

AR-LC6/Large capacity tray AR-F15/Finisher AR-F16/Saddle stitch finisher

(Boot/PCL, PS)

SOFT KEY

AR-CF2/Inserter AR-PN2A/B/C/D / Punch unit AR-P19/Printer expansion kit

SOFT KEY

AR-PK5/PS3 expansion kit AR-PF1/Barcode font kit AR-FR11/Data security kit

SOFT KEY

Fax BOX

AR-NS3/Network scanner expansion kit AR-FX8/ Facsimile expansion kit*1 AR-MM9/FAX expansion memory (8MB)*1

AR-U11M/Sharpdesk 1 license kit

AR-U15, AR-U15M / Sharp desk 5 license kit

AR-U1AM/Sharpdesk 50 license kit

AR-U1BM/Sharp desk 100 license kit

Up to country

SOFT KEY

NIC

(Boot/PCL, PS)

*1: North America, Europe, Australia, New Zealand, Singapore, Taiwan

AR-M550/M620/M700 CONFIGURATION 2 - 1

: Feb. 9 2004

(3) Option combinations

STD:Standard provision, ❍:Installable, ×:Not installable

Option Machine model

Copier model Network printer

AR-M550U/

M620U/M700U

AR-M550N/

M620N/M700N

Paper feed

Section

Large capacity tray(AR-LC6) ❍❍

Item

system Paper exit system Finisher (AR-F15) ❍❍

Saddle stitch finisher (AR-F16) ❍❍ Inserter (AR-CF2) ❍❍ Punch unit (AR-PN4A/4B/4C/4D) ❍❍For finisher and saddle stitch

Electrical system (Printer controller)

Printer expansion kit(AR-P19) ❍ STD PS3 expansion kit(AR-PK5) ❍❍For installation to the AR- Barcode font kit(AR-PF1) ❍❍

Software Data security kit (Not acknowledged version) (AR-FR11) ❍❍

Network scanner expansion kit (AR-NS3) ❍❍ Sharp desk 1 license kit (AR-U11M) ❍❍ Sharp desk 5 license kit (AR-U15M) ❍❍ Sharpdesk 50 license kit (AR-U1AM) ❍❍ Sharpdesk 100 license kit (AR-U1BM) ❍❍

FAX system Facsimile expansion kit (AR-FX8) ❍❍

FAX expansion memory (8MB)(AR-MM9) ❍❍

Remarks

finisher

M550U/M620U/M700U, the printer expansion kit, AR-P19, is required.

2. Block diagram

Telephone Line

Fax unit (Option)

MFP Control PWB

USB

Network

Por t

Paper Exit and switch

back Section

Pararell

Por t

HDD

Fusing Section

ADU Section

SPF Unit (CIS)

Image Scanner (reading) Section (CCD)

Scanner Control PWB

Scanner(writing)

(LSU) Section

Drum Section

Paper Transport Section

Operating Section

Engine Control Section

(PCU PWB)

Toner Bottle

Toner Hopper

Developer SectionTransfer Section

Manual Paper

Feed Tray

Finisher (Option)

Punch Unit

(Option)

Inserter

(Option)

DC Power Unit

AC Power Unit

Paper Feed Tray 1 Paper Feed Tray 2

AR-M550/M620/M700 CONFIGURATION 2 - 2

Paper Feed Tray 3

Paper Feed Tray 4

Large Capacity

Paper Tray Unit

(Option)

: Feb. 9 2004

[3] SPECIFICATIONS

1. Basic specifications

A. Main unit

(1) Type

Type Console Clip tray Provided

Operation mode Format

Copy mode Monochrome digital (Electronic photo graphic)

(2) Target users

Mode Model Volume of usage

Copy mode AR-M550N/

M550U

AR-M620N/ M620U

AR-M700N/ M700U

(3) Engine speed

Paper size

A4, 8.5×11 55ppm 62ppm A4R, 8.5×11R 40ppm 45ppm A5R/5.5×8.5R, Invoice-R B5 55ppm 62ppm B5R,

Executive-R B4/8.5×14 35ppm 39ppm A3/11×17 30ppm 34ppm Extra 30ppm 34ppm Postcard Since the next paper is fed after completion of paper

AR-M550N/

M550U

40ppm 45ppm

exit outside the machine, it depends on the machine composition.

(4) External dimensions (W x D x H)

Packaged – Main unit 728 x 679 x 1050mm (Height: Floor –

When an option is installed (Machine occupying area) Main unit + LCC installed 1347 x 679 x 1192mm Main unit + Saddle

finisher/ Saddle finisher installed

Main unit + LCC + Finisher/ Saddle finisher installed Main unit + Inserter + Finisher/ Saddle finisher Main unit + LCC + Inserter + Finisher/ Saddle finisher installed

(5) Weight

AR-M550N/M620N/M700N Packaged About 212 Kg

AR-M550U/M620U/M700U Packaged About 214 Kg

Scope – 250,000 pages/month Average

copy volume Scope – 300,000 pages/month Average

copy volume Scope – 300,000 pages/month Average copy volume

Glass surface) 728 x 679 x 1192mm (Height: Floor – SPF top)

1794 x 679 x 1192mm

1887 x 679 x 1192mm

2079 x 679 x 1192mm

2156 x 679 x 1192mm

Main unit 185 Kg

– 40,000 pages/month

– 50,000 pages/month

AR-M620N/

M620U

AR-M700N/

M700U 70ppm 48ppm

48ppm

70ppm

48ppm

45ppm 39ppm 39ppm

(6) Languages supported

Key sheet language support

Japanese, English (America English/UK English), German, French, Spanish, Italian, Dutch, Swedish, Norwegian, Finnish, Danish, Czech, Polish, Hungarian, Greek, Chinese

(7) Internal auditor

System Key operation system No. of departments 500

(8) Operation panel

Type Dot matrix LCD (640 x 240dots) Operating procedure LCD drive display area LCD backlight Fluorescent lamp backlight system LCD brightness adjustment Character used in LCD

Touch-panel input

153.5 × 57.5mm

Provided

Type Sharp/Fujitsu font Dot Kanji: 16 x 16dots, Alphabet and

Bold text display

numeral: 8 x 16dots, 16 x 16dots ❍ (Mixed used in a same area or a

same sentence is inhibited.)

(9) Controller board

CPU RM7065 (64bit RISC CPU, 525 MHz) Interface IEEE1284 Parallel 1 port (* For printer/servicing) Ethernet 1 port* USB2.0 1 port (* For printer/servicing) Expansion port PCI slot 1 slot Memory 128MB (onboard) Memory expansion slot

*: Standard for the AR-M550N/M620N/M700N. The Printer expansion

kit AR-P19 is required for the AR-M550U/M620U/M700U.

1 slot (168pin SDRAM DIMM compatible) 64MB/ 128MB/256MB expandable

(10) Hard disk

Hard disk capacity 40GB Hard disk storage

quantity

60000 sheets

(11) Power source

a. Dehumidifier functionality (Option)

Section Paper conveyor section/Scanner section

b. Operating voltage/power consumption

Power consumption

Power supply voltage/frequency

100V (Japan) 50/60Hz 1450 Other countries in 100V system 50/60Hz 1800 Other countries in 200V system 50/60Hz 1840

With full options

Max.

AR-M550/M620/M700 SPECIFICATIONS 3 - 1

: Feb. 9 2004

2. Engine specifications

A. Paper feeding, paper conveyance, and discharge section

(1) Paper feeding performance

Type 4-stage paper feed tray (Parallel LCC + 2 tray + Multi manual paper feed) Paper feed method Paper is fed from the above by the front loading system. Dehumidification heater Japan Standard

Except for Japan Option

• Tray 1 (Left tray in the parallel LCC)

Paper size

(set by software)

A4, 8.5" x 11"

Paper size

change method

Size setting by user

Paper type

setting

Paper size setting

when shipping

YES Japan : A4

Inch Series:

8.5" x 11" AB Series: A4 (16K is not supported.)

*1: Time required from tray insertion to empty detection when paper is empty.

• Tray 2 (Right tray in the parallel LCC)

Paper size (set by

software)

Japan:

A4, B5, 8.5" x 11" AB series (Europe, SCA):

A4, 8.5" x 11" AB series (Other):

A4, B5, 8.5" x 11" Inch Series:

8.5" x 11", A4

Paper size

change method

Size setting by serviceman (B5 available through bolt fixing and setting by serviceman)

Paper type

setting

YES Japan: B5

Paper size setting

when shipping

Inch Series:

8.5" x 11" AB Series: A4 (16K is not supported.)

*1: Time required from tray insertion to empty detection when paper is empty.

• Tray 3 (Multi-purpose tray)

Paper size

A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR 11 x 17, 8.5 x 14,

8.5 x 13, 8.5 x 11,

8.5 x 11R, 7.25 x

10.5R, 5.5 x 8.5R, Special size (Tab paper is of A4; limited to tab width 12mm – 20mm/8.5 x 11; tab width 6.1mm – 17mm.)

*1: For 105g/m

or above, A4/8.5 x 11 or less. For 128g/m2 or above, horizontal feed only.

Paper size

change method

Guide adjustment by user

Paper type

setting

YES Shipped with

Paper size

setting when

shipping

the paper guide width at Max.

*2: For multi copy and back surface copy, single feed only.

• Tray 4 (500-sheet paper feed tray)

Paper size

A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR 11 × 17, 8.5 × 14,

8.5 × 13,

8.5 × 11,

8.5 × 11R,

7.25 × 10.5R

*1: For 105g/m

Paper size

change

method

Guide adjustment by user

or above, A4/8.5 x 11 or less. For 128g/m2 or above, horizontal feed only.

Paper

type

setting

Paper size

setting when

shipping

YES Shipped with

the paper guide width at Max.

Normal paper: 60 – 105g/m (16 – 28 lbs) *1, *2 Thick paper: 106 – 128g/m (29 – 34 lbs) 205g/m 176g/m

*2: For multi copy and back surface copy, single feed only.

Allowable paper type and weight

for paper feed Normal paper: 60 – 105g/m (16 – 28lbs)

Allowable paper type and weight

for paper feed

Normal paper: 60 – 105g/m (16 – 28lbs)

Allowable paper type and weight

for paper feed

Normal paper: 60 – 105g/m (16 – 28 lbs) Thick paper: 106 – 128g/m (29 – 34 lbs)

(110 lbs)

205g/m

176g/m

(65 lbs) OHP, label sheet, tab paper *1, *2

Allowable paper type and weight

for paper feed

(110 lbs)

(651 lbs)

Paper capacity

(Standard paper)

Japan: 900

sheets (64g/m Except for Japan: 800 sheets

)

(80g/m

Paper capacity

(Standard paper)

Japan: 1300

sheets (64g/m Except for Japan: 1200 sheets

)

(80g/m

Paper capacity

(Standard paper)

Standard paper

Japan: 550 sheets (64g/m

Except for Japan: 500 sheets (80g/m

OHP 40 sheets Automatic

Tab paper Enable For 8K, 16K, and 16KR,

Paper capacity

(Standard paper)

Japan: 550 sheets (64g/m Except for Japan: 500 sheets (80g/m

Normal paper,

)

printed paper, recycled, letterhead,

)

punched paper, color paper, thick paper

Paper type

Normal paper, printed

)

paper, recycled, letterhead, punched paper, color paper

remaining

detection Enable (Paper empty and 3

steps)

Paper

Paper type

remaining

detection

Normal paper,

printed paper,

)

recycled, letterhead, punched paper, color paper

Enable (Paper empty and 3 steps)

Paper type Document detection

Normal paper, printed paper,

)

recycled, letterhead, punched paper, color paper, thick

)

paper, label sheet, OHP, tab paper

Automatic detection Auto-AB

detection Auto-inch

setting is made manually.

Detection disregard setting

Paper type Document detection

Automatic detection Auto-AB

Automatic detection Auto-inch

A3, B4, A4, A4R, B5, B5R, 8.5×13

11 × 17, 8.5 × 14,

8.5 × 11, 8.5 × 11R,

7.25 × 10.5R

For 8K, 16K, and 16KR, setting is made manually.

Tray lift time

Up Within

Down Free fall

Tray lift time

Up Within

Down Free fall

A3, B4, A4, A4R, B5, B5R,

8.5 × 13

11 × 17,

8.5 × 14,

8.5 × 11,

8.5 × 11R,

7.25 ×

10.5R

Enable

Enable (Paper empty and 3 steps)

12sec *1

Paper

remaining

detection

Enable (Paper empty and 3 steps)

Paper

remaining

detection

AR-M550/M620/M700 SPECIFICATIONS 3 - 2

: Feb. 9 2004

• Manual paper feed

Paper size

A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR, Postcard 11×17, 8.5×14,

8.5×13, 8.5×11,

8.5×11R,

7.25×10.5R,

5.5×8.5R

Paper type

setting

YES Thin paper: 52 – 59g/m

*1: For paper exceeding 105g/m

Allowable paper type and

weight for paper feed

(14 – 15lbs) (Tab paper in single feed) Normal paper: 60 – 105g/m Thick paper: 106 – 128g/m 176g/m 205g/m OHP, postcard, label sheet, tab paper*1, *2

(16 – 28 lbs)

(65 lbs) cover

(110 lbs) Index

, A4/8.5 x 11 or smaller. For paper exceeding 128g/m2, horizontal feed only.

(29 – 34 lbs),

(Standard paper)

Plain paper : 100 sheets (80g/m Postcard: 20 sheets OHP: 20 sheets

Paper capacity

*2: Multi-back surface copy is enable only in single feed.

• Duplex System Non stack system

Paper size A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K,

16KR, 11 x 17, 8.5 x 14, 8.5 x 13, 8.5 x 11, 8.5

x 11R, 8.5 x 5.5R Type and weight of paper which can be passed

Plain paper: 60 – 105g/m² (16 – 28lbs)

Thick paper: 106 – 128g/m² (29 – 34 lbs),

176g/m² (65 lbs cover)

205g/m² (110 lbs) Index

(2) Finishing performance

Paper exit position / system

Paper exit capacity 250 sheets (80g/m Paper exit paper size/ kind Remaining paper detection Paper exit paper full detection

Main unit top surface face-down paper exit

paper)

All kinds of paper which can be fed

None

Provided

B. Scanner section (read)

(1) Type

Document table mode / SPF (front side) mode Scanning method By the CCD image sensor.

SPF (back side) mode Scanning method By the CIS image sensor

(2) Original standard position, scanning size, and

scanning area

a. Original standard position

Document table Left bottom reference SPF Center reference

b. Scanning size

Max. original size AB Series A3

Inch Series 11 × 17

(3) Resolution

Scan resolution (dpi)

Platen Magnification

ratio

SPF Magnification

ratio When in

single copy When in

duplex copy (front) CCD

When in duplex copy (back) CIS

25 – 99

600 × 600 600 × 600 600 × 600

25 – 99

600 × 367 600 × 367 600 × 367 600 × 600

600 × 600 600 × 600

600 × 300 600 × 300 600 × 600 600 × 600

Copy mode

Normal

ratio

Normal

ratio

101 – 171 172 – 400

600 ×

(600 × 2)

101 – 117 118 – 200

600 ×

(600 × 2)

600 ×

(600 × 2)

Paper type Document detection

Normal paper, recycled

)

paper, printed paper, punched paper, color paper, letterhead, back paper, label paper, thick paper, OHP, tab paper (tab width 20mm or less)

Input and send resolution (dpi)

* Except for FAX sending

Input and send resolution (dpi)

(4) Gradation

256 gradations (8bit) 2 gradations (1bit)

(5) Scanning speed

DSPF 65 surfaces (single)

(6) Light source

Type None-electrode xenon lamp (Front), LED (Back)

(7) Scanning sensor

Type Monochrome CCD

Paper empty

Automatic detection Auto-AB

Automatic detection Auto-inch

Detection of 8K and 16K in the manual paper feed tray is not performed.

When in the Fax send mode and the scanner FAX broadcast mode

Select mode

Input resolution: OC

Input resolution: SPF simplex

Input resolution: SPF simplex (front) CCD

Input resolution : SPF duplex (back) CIS

Communication resolution

Select mode 200 × 200 300 × 300 400 × 400 600 × 600 Input resolution:

OC Input resolution:

SPF simplex Input resolution:

SPF duplex (front) CCD

Input resolution: SPF duplex (back) CIS

Communication resolution

A3, B4, A4, A4R, B5, B5R, Postcard, A5R

11×17, 8.5×14, 8.5×13,

8.5×11, 8.5×11R,

7.25×10.5R, 5.5×8.5R

Fine

Standard

600 × 600

600 × 367

600 × 600

600 × 300

203.2 ×

200 × 100

600 × 600 600 × 600 600 × 600 600 × 600

600 × 367 600 × 367 600 × 367 600 × 367

600 × 600 600 × 600 600 × 600 600 × 600

600 × 300 600 × 300 600 × 300 600 × 300

200 × 200 300 × 300 400 × 400 600 × 600

203.2 ×

97.8

Scanner mode

text

600 ×

600

600 ×

367

600 ×

600

600 ×

300

195.6 Internet FAX

200 ×

200

Super

fine test

600 ×

600

600 ×

367

600 ×

600

600 ×

300

FAX

203.2 × 391

200 ×

400

YES

Ultra

fine text

600 × 600

600 × 367

600 × 600

600 × 300

406.4 × 391

400 ×

400

detection

600dpi send *

–

600 ×

600

Input Output

Scans per minute

76 surfaces (duplex)

AR-M550/M620/M700 SPECIFICATIONS 3 - 3

: Feb. 9 2004

C. Scanner section (write)

(1) Type

Scan system Laser scanning

(2) Laser unit specifications

Rotation speed

Mirror surfaces 14 surfaces Laser power

Laser beam size Main scan: 60 – 85 mm,

Laser wavelength 770 – 795 nm Scan width (sub scan direction)

34000 rpm (AR-M550N/U, AR-M620N/U) 40000 rpm (AR-M700N/U)

0.385±0.04 mW (AR-M550N/U, AR-M620N/U)

0.480±0.04 mW (AR-M700N/U)

sub scan: 75 – 110 mm

AB series: 420 mm Inch series: 432mm

(3) Resolution

Main scanning direction Sub scanning direction

600dpi 600dpi

(4) Gradation

2 gradations (1bit)

D. Image processing section

(1) Imaging speed

335 mm/sec (AR-M550N/U, AR-M620N/U)

395 mm/sec (AR-M700N/U)

(2) Photosensitive drum

Type OPC φ80mm Life

55ppm: 250K, 62/70ppm: 300K

(3) Toner

Capacity 1430/1650g (Other countries), 1275g (Japan)

(4) Developer

1 1

Capacity Life

725g x 2 (2 bags are used.) 55ppm: 250K, 62/70ppm: 300K

(5) Charging

Type Corotron

Voltage

–590V±2V

(6) Exposure

System Exposure from laser diode

(7) Developing system

System Dry, 2-component magnetic brush development Voltage –500V±5V (Developing mode)

+150V (Cleaning mode)

(8) Transfer

System Static electricity transfer (transfer belt method) Transfer section

35µA (AR-M550N/U, AR-M620N/U) 40µA (AR-M700N/U) Cleaning mode (AC 4.5kV, DC –100V)

(9) Paper separation system

System Curvature separation + Separation pawl

(10) Discharging

System Discharging lamp method

(11) Cleaning

System Counter blade system

(12) Waste toner collector capacity

Capacity 40% of toner capacity

E. Fuser section

(1) Type

System Heat roller attachment system

(2) Fuser temperature

Copy/Print

mode

Pre-heat mode

(4) Heat roller

Type Teflon lined Life 300K

(5) Pressure roller

Type Silicone rubber roller Life 300K

(6) Method

Forced release by releasing tabs

Normal mode control temperature Heat roller Normal mode control temperature Sub heat roller Thick paper mode control temperature Heat roller Thick paper mode control temperature Sub heat roller Energy saving mode control temperature Heat roller Control temperature in the energy save mode Sub heat roller

Mode

(Unit: °C)

Control temperature

Fusing roller Auxiliary heat roller

Inch

(U.S.A.,

Canada)

200 205 200 205 200 205 200 205 200 205 200 205 200 205 200 205 170 170 170 170 170 170 170 170

AB_B

(Europe, U.K.)

AB_A

(Australia)

Inch

(U.S.A.,

Canada)

AB_B

(Europe, U.K.)

AB_A

(Australia)

F. Drive section

Drive section Motor name Motor type Image scanner Scanner motor Stepping motor Developing system Developing motor DC brush-less motor Paper feed and conveyance Transfer, OPC drum OPC drum motor DC brush-less motor Fusing Fusing motor DC brush-less motor

Paper feed motor DC brush-less motor

AR-M550/M620/M700 SPECIFICATIONS 3 - 4

: Feb. 9 2004

3. Operating specifications

A. Common operations

(1) Warm-up, jam recovery time, low power mode, sleep mode

a. Warm-up time (ambient temp. of 20°C)

After turned on Max. 120 seconds Reset time from preheat mode Within 30 seconds

b. Jam recovery time

Jam recovery time Within approx. 30 sec (Condition: door open/

fusing unit pull-out, after leaving for 60sec, standard condition, polygon stop) Under 30 seconds (conditions: door open)

c. Low power mode, sleep mode

Low power consumption mode

Reset time from low power mode 30sec Power consumption in the sleep mode Shift time to sleep mode 90 min (Max. 240 min)

*1: Calculation formula: 3.85 x ipm + 5W *2: Calculation formula: 3.85 x ipm + 50W (ipm: input page per minute)

S/U model*1 216.75W 243.7W M/N model*2 261.75W 288.7W

S/U model*1 20W or less M/N model*2 95W or less

(2) Size sensing summary

Yes: detection; yes USER: by USER setting USER 1: USER SETTING 1 (INCH series) USER 2: USER SETTING 2 (AB series) SVC: By serviceman setting No: detection; no (engine performs as extra mode) N/A: Not applicable PRT Key OP: by printer key operator program T/C: Simulation setting(by Serviceman) The size detection- off mode will be added in printer key operator program. Refer to Front panel spec.

Destination All Destinations

Paper size

A6-R N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A

5.5 x 8.5 in.-R N/A N/A Yes *2 N/A N/A N/A N/A Yes *2 N/A Yes USER A5-R N/A N/A N/A Yes *2 N/A N/A N/A N/A Yes *2 USER Yes B5 N/A SVC N/A Yes *2 N/A Yes N/A N/A Yes *2 USER Yes B5R N/A N/A N/A Yes *2 N/A Yes N/A N/A Yes *2 USER Yes Executive-R N/A N/A Yes *2 N/A Yes N/A N/A Yes *2 N/A Yes USER Letter USER SVC Yes N/A Yes N/A SVC Yes N/A Yes USER Letter-R N/A N/A Yes *2 N/A Yes N/A N/A Yes N/A Yes USER A4 USER SVC N/A Yes N/A Yes SVC N/A Yes USER Yes A4-R N/A N/A N/A Yes *2 N/A Yes N/A N/A Yes USER Yes Legal N/A N/A Yes *3 N/A Yes *2 N/A N/A Yes *3 N/A Yes USER Foolscap N/A N/A N/A Yes *3 N/A Yes *2 N/A N/A Yes *3 USER Yes B4 N/A N/A N/A Yes *3 N/A Yes *2 N/A N/A Yes *3 USER Yes A3 N/A N/A N/A Yes *3 N/A Yes *2 N/A N/A Yes *3 USER Yes 11 x 17 in N/A N/A Yes *3 N/A Yes *2 N/A N/A Yes *3 N/A Yes USER Postcard N/A N/A N/A N/A N/A N/A N/A N/A Yes N/A N/A Custom 148-181mm N/A N/A USER USER N/A N/A N/A USER USER N/A N/A 182-432mm N/A N/A USER USER N/A N/A N/A USER USER N/A N/A 8K *1 N/A N/A USER USER USER USER N/A USER USER USER USER 16K *1 N/A N/A USER USER USER USER N/A USER USER USER USER

16K-R *1 N/A N/A USER USER USER USER N/A USER USER USER USER *1: China destination only *2: Except Tab Paper type *3: Except Heavy/Label/Transparency/Tab paper type

Tray 1

tandem

tray left

tray right

AR-M550N/U AR-M620N/U AR-M700N/U

Tray 2

tandem

Tray 3

Universal tray

USER 1 USER 2 USER 1 USER 2 USER 1 USER 2 USER 1 USER 2

274.5W

319.5W

Tray 4

Drawer Tray

LCC desk

Multi bypass tray Inserter tray

AR-M550/M620/M700 SPECIFICATIONS 3 - 5

(3) Paper type summary

Yes: This function is effective No: This function is invalid USER: by USER setting

Paper Type Print job Copy job Fax job I-Fax job Filing job F-R attribute Duplex disable Staple disable Punch disable Standard paper USER USER USER USER USER NO NO NO NO Recycled paper USER USER USER USER USER NO NO NO NO Color paper USER USER USER USER USER NO NO NO NO Printed paper USER USER USER USER USER YES NO NO NO Letterhead USER USER USER USER USER YES NO NO NO Thick paper USER USER USER USER USER NO NO YES NO Punched paper USER USER USER USER USER NO NO NO NO Label sheet USER USER USER USER USER NO YES YES YES OHP USER USER USER USER USER NO YES YES YES Tab paper USER USER USER USER USER NO YES NO NO User Type USER USER USER USER USER USER USER USER USER

(4) Effective print area

C A

Paper size

Ledger 11.0 (inch) 6600 17.0 (inch) 10200 6400 10000 100 100 100 100 Legal 8.5 (inch) 5100 14.0 (inch) 8400 4900 8200 100 100 100 100 Foolscap 8.5 (inch) 5100 13.0 (inch) 7800 4900 7600 100 100 100 100 Letter 11.0 (inch) 6600 8.5 (inch) 5100 6400 4900 100 100 100 100 Letter-R 8.5 (inch) 5100 11.0 (inch) 6600 4900 6400 100 100 100 100 Executive-R 7.25 (inch) 4350 10.5 (inch) 6300 4150 6100 100 100 100 100 Invoice-R 5.5 (inch) 3300 8.5 (inch) 5100 3100 4900 100 100 100 100 A3 297 (mm) 7015 420 (mm) 9921 6815 9721 100 100 100 100 B4 257 (mm) 6070 364 (mm) 8598 5870 8398 100 100 100 100 A4 297 (mm) 7015 210 (mm) 4960 6815 4760 100 100 100 100 A4R 210 (mm) 4960 297 (mm) 7015 4760 6815 100 100 100 100 B5 257 (mm) 6070 182 (mm) 4299 5870 4099 100 100 100 100 B5R 182 (mm) 4299 257 (mm) 6070 4099 5870 100 100 100 100 A5R 148 (mm) 3496 210 (mm) 4960 3296 4760 100 100 100 100 A6R 105 (mm) 2480 148 (mm) 3496 2280 3296 100 100 100 100 Postcard 100 (mm) 2362 148 (mm) 3496 2162 3296 100 100 100 100

– –––––reference 4.23 (mm) 4.23 (mm) 4.23 (mm) 4.23 (mm)

NOTE: Engine can make void area by force. Because when real paper size is smaller than the detected size, engine can stop laser shot to prevent

machine damage that causes from created drum image which is out of paper.

(mm/inch) (dots) (mm/inch) (dots) (dots) (dots) (dots) (dots) (dots) (dots)

ABCDEFGH

(5) Image rotation in staple mode

Staple mode by Finisher/Saddle stitch finisher need 180 degrees image rotation.

Because by mechanical reasons, paper edge which to be stapled cannot be changed.

Finisher Mode Image rotation

Finisher/Saddle stitch finisher

Non-staple 180°C

Staple 180°C

AR-M550/M620/M700 SPECIFICATIONS 3 - 6

: Feb. 9 2004

B. Copy mode

(1) Document size

Scan mode

Original stand mode

Paper

type AB Series

Location

AB-1 — 297 x AB-2 — A3, A4, A4R, A5, B5, B5R, 216×330

AB-3 — 8K, A4, AR4, A5, B4, 16K, 16KR Inch Series

DSPF mode AB

Series Inch

Series

Inch-1 — 5.5 × 8.5 11 × 17 11×17, 8.5×14, 8.5×11, 8.5×11R, 5.5×8.5

Inch-2 — 11×17, 8.5×13, 8.5×11, 8.5×11R, 5.5×8.5

AB-1 ——A5 A3 A3, B4, A4, A4R, B5, B5R, A5, 8.5×11R, 216×330

AB-2 —— 8K, A4, A4R, B4, 16K, 16KR, A5, 8.5×11, 216×330

Inch-1 ——8.5 × 5.5 11 × 17 11×17, 8.5×14, 8.5×11, 8.5×11R, 8.5×5.5, A4

Inch-2 —— 11×17, 8.5×13, 8.5×11, 8.5×11R, 8.5×5.5, A4 Mix paper feed (Same series, same width paper) enabled

(2) Paper size

Paper type

AB Series ——A6 (A6R) Postcard A3 A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR,

Inch Series ——8.5 × 5.5 11 × 17 11×17, 8.5×14, 8.5×13, 8.5×11, 8.5×11R,

Dimensions Paper size

Min. Max. Min. Max.

(3) Exposure

a. Density/copy image quality process

Exposure speed Binary: Text (Auto/Manual), Text/Photo, Photo Number of manual steps Toner save mode YES

b. Resolution

• Scanning Main scanning direction Sub scanning direction

Basic resolution Basic resolution

600dpi 600dpi

• Write Main scanning direction Sub scanning direction

Basic resolution Basic resolution

600dpi 600dpi

c. Gradation/image processing

Scanning Printing

256 gradations (8bit) 2 gradations (1bit)

d. Distortion

203mm

9 steps

Print horizontal line

Print vertical line

Dimensions Paper size

Min. Max. Min. Max.

A5 A3 A3, B4, A4, A4R, B5, B5R, A5

431.8mm

1mm

| D |

60 m

Paper size Note

Postcard

7.25×10.5R, 5.5×8.5R

(4) Copy magnification

a. Copy magnification (independent magnification by direction is

possible)

Main scanning direction Sub scanning direction

Mode

Zoom mode 25 – 400(200)%* Zoom mode 25 – 400(200)%* Fixed

magnification mode (AB Series)

Fixed magnification mode (Inch Series)

Magnification range/

fixed magnification

25, 50, 70, 81, 86, 100, 115, 122, 141, 200, 400%

25, 50, 64, 77, 100, 121, 129, 141, 200, 400%

Mode

Fixed magnification mode (AB Series)

Fixed magnification mode (Inch Series)

Magnification range/

fixed magnification

25, 50, 70, 81, 86, 100, 115, 122, 141, 200, 400%

25, 50, 64, 77, 100, 121, 129, 141, 200, 400%

* When copying from SPF: 25 – 200%

Preset copy magnification ratio: 4

b. Copy magnification precision

Main scanning direction Sub scanning direction

Copy

magnification Normal copy 100% ± 0.8% Normal copy 100% ± 0.8% Enlargement copy Set magnification

Reduction copy Set magnification

Magnification

precision

± 1.0%

Copy

magnification

Enlargement copy Set magnification

± 1.0%

Reduction copy Set magnification

± 1.0%

c. Zoom method

Main scanning direction Performed through image processing Sub scanning direction Performed by changing image processing

and scanning speed

(5) Job speed

a. First copy time

AR-M550N/

M550U Document table Within 3.9sec Within 3.9sec DSPF Within 6.1sec Within 6.1sec

∗ Measurement conditions: When paper of A4/8.5 x 11 is fed from the

main unit tray, the polygon motor is rotating.

AR-620N/

M620U

Magnification

precision

AR-M700N/

M700U Within 3.3sec Within 5.5sec

AR-M550/M620/M700 SPECIFICATIONS 3 - 7

: Feb. 9 2004

b. Copy speed

AR-M550N/M550U AR-620N/M620U

Copy mode Paper size

Original stand mode

A4, 8.5×11 55 55 55 62 62 62 A4R, 8.5×11R 404040454545 A5R/5.5×8.5R, Invoice-R404040454545 B5 55 55 55 62 62 62 B5R, Exective-R 40 40 40 45 45 45 B4/8.5×14 35 35 35 39 39 39 A3/11×17 30 30 30 34 34 34 Extra 303030343434 8K 35 35 35 39 39 39 16K 555555626262 16KR 40 40 40 45 45 45 Postcard Since the next paper is fed after completion of paper exit outside the machine, it depends on the machine composition.

Reduction

copy (25%)

Copy magnification Copy magnification

Normal copy

(100%)

c. Job speed

• BLI standards

AR-M550N/

M550U

S → S 50.1cpm (91%) 56.4cpm (91%) S → D 49.0cpm (89%) 53.3cpm (86%) D → D 51.7cpm (94%) 57.0cpm (92%)

AR-M620N/

M620U

AR-M700N/

M700U

63.0cpm (90%)

58.8cpm (84%)

63.0cpm (90%)

∗ S → S: A4/8 x 11 documents 10 sheets, copy 5 sets ∗ S → D: A4/8 x 11 documents 10 sheets, copy 5 sets ∗ D → D: A4/8 x 11 documents 10 sheets (20 pages), copy 5 sets

• Bertl standards

AR-M550N/

M550U

AR-M620N/

S → S 46.2cpm (84%) 50.8cpm (82%) S → D 33.6cpm (61%) 34.1cpm (55%) D → D 49.0cpm (89%) 53.9cpm (87%)

M620U

AR-M700N/

M700U

57.9cpm (82%)

36.9cpm (52%)

58.7cpm (83%)

∗ S → S: A4/8 x 11 documents 5 sheets, copy 5 sets ∗ S → D: A4/8 x 11 documents 10 sheets, copy 1 set ∗ D → D: A4/8 x 11 documents 5 sheets (10 pages), copy 5 sets

d. Maximum no. of copies

Multi max. quantity 999 sheets

• Max copy set quantity by each copy mode Single-side copy 999 sheets

Duplex copy 999 sheets

(6) Copy area

(Front edge)

Printed image

(image area)

Feeding direction

Enlargement

copy (400%)

AR-M700N/M700U

Reduction

copy (25%)

Normal copy

(100%)

Enlargement copy (400%)

copy (25%)

Copy magnification

Reduction

Normal copy

(100%) 70 70 70 48 48 48 48 48 48 70 70 70 48 48 48 45 45 45 39 39 39 39 39 39 45 45 45 70 70 70 48 48 48

• Printable range A3 289 × 412mm 11 × 17 271 × 424mm

B4 242 × 356mm 8.5 × 14 208 × 348mm A4 202 × 289mm 8.5 × 13 208 × 322mm B5 168 × 249mm 8.5 × 11 208 × 271mm A5 140 × 202mm 5.5 × 8.5 132 × 208mm Executive 183 × 259mm 8K 270 × 390mm Postcard 92 × 140mm 16K 195 × 270mm

• Image loss

One side copy (excluding A3

Front

edge (A) Max. 5mm

Rear

edge (B) Max. 5mm

Total

(C + D) Max. 6mm

Left edge

(C)

Max.

3.0mm

(11 × 17)) One side copy

for A3 (11 × 17) Duplex copying Max.

OHP copying Max.

Max. 5mm

5mm

10mm

Max. 7mm

Max. 10mm

Max. 6mm

Max.

3.0mm Max.

3.0mm

• Void area

One side copy (excluding A3

Front

edge (A)

Max. 5mm

Rear

edge (B)

Max. 5mm

Total

(C + D) Max.

8mm

Left edge

(C)

Max.

3.0mm

(11 × 17)) One side copy

for A3 (11 × 17) Duplex copying Max.

OHP copying Max.

Max. 5mm

5mm

10mm

Max. 7mm

Max. 10mm

Max. 8mm

Max.

3.0mm Max.

3.0mm

• Reference shift (off-center shift) normal ratio Main unit (OC

mode)

Simplex ±1.5mm Duplex ±1.7mm

Overall (SPF) Simplex S-S ±2.8mm

Simplex D-S ±3.5mm Duplex S-D ±3.0mm Duplex D-D ±3.5mm

Enlargement copy (400%)

Right

edge (D)

Max.

3.0mm

Max.

3.0mm Max.

3.0mm

Right

edge (D)

Max.

3.0mm

Max.

3.0mm Max.

3.0mm

Dimensions show void area

(Rear edge)

AR-M550/M620/M700 SPECIFICATIONS 3 - 8

: Feb. 9 2004

(7) Copy functions

Automatic paper selection ❍ Automatic magnification ratio

selection Vertical/horizontal

independent magnification ratio Paper type selection ❍ By type setup Auto tray switching ❍ Rotation copy ❍ Electronic sort ❍ Rotation sort ❍ Job reservation ❍ Tray installation priority × Program call/register ❍ Document filing ❍ Preheat function ❍ Set by the key operator Auto power shut off function ❍ Set by the key operator program Dept. management ❍ 500 department Process control ❍ Tandem copy ❍ (Via network) Indefinite document size input ❍ Indefinite paper size input ❍ Binding margin ❍ Edge erase/Center erase ❍ 1 set 2 copy ❍ Cover/Insert paper/Tab insert paper OHP insert paper ❍ Tab copy ❍ Centering × Multi shot (N in 1) ❍ (2 in 1/4 in 1) (Centering provided) Card shot ❍ Center binding ❍ (Centering provided) Duplex copy system switch ❍ Large volume document mode ❍ (Max. 10000 sheets) Black-white reversion ❍ Shading × Mirror image ❍ Enlargement continuous copy × Repeat × Date print × Stamp × Page print ×

❍

C. Image send function

(1) Mode

Scanner (Scan to E-mail, Scan to Sharp desk, Scan to FTP, Scan to HDD ), FAX, Internet FAX

(2) Support system

Mode Scanner Internet FAX FAX Supported server

(3) Support image

Mode TIFF, PDF, TIFF-F, TIFF-FX Compression

system

SMTP server

FTP server

Scanner Internet FAX FAX

Non-compression

G3 (1st dimension)

= MH (Modified

Huffman)

G4 = MMR

(Modified MR)

POP server

SMTP server

ESMTP server

MH, MMR MH, MR,

–

MMR, JBIG

(4) Image process

Mode Scanner Internet FAX FAX half tone

reproduction Density

adjustment Image quality

selection Resolution

(Differs depending on the file type/ communication system.)

200×200dpi * 200×100dpi * Normal text

300×300dpi 200×200dpi Small text

400×400dpi 200×400dpi Fine text

600×600dpi 400×400dpi Ultra fine text

Equivalent to 256 gradations

Auto + 5 steps

Half tone ON/OFF (*: Not available)

(203.2×97.8dpi)*

(203.2×195.6dpi)

(203.2×391dpi)

(406.4×391dpi)

– 600×600dpi –

(5) Address specification

Mode Scanner Internet FAX FAX LDAP ❍ (Can be registered as one-touch address.) Address specification No. of onetouch registration items Group ❍ Registered from the one-touch dial and the direct

Program ❍ (8 items) Direct address input

Chain dial (Direct address input)

Resend The previous address is called. Reduction

address selection

Specified by one-touch, group, or direct address

input.

Max. total 999 items

(of which 200 can be assigned to FTP and/or

desktop)

dial. (Max. 500 items)

Soft keyboard Input by the 10-

key, # key, and *

key.

– Used together

with Pause. Up to

64 digits.

The address registration number is called by the 10-

key input.

(6) Multiple address specification

Mode Scanner Internet FAX FAX Address specification No. of

registration items of direct address input *

Broadcast send ❍ (Broadcast

Sequential send request

*: Direct address input: 10-key other than one-touch, and soft keyboard

input

• When broadcast includes FAX, the resolution is set to the FAX reso-

lution.

• The compression system in broadcast conforms to the key operator

setup.

Specified by one-touch, group, or direct address

input *.

Max. total 5000 items of group/interface broadcast

❍

send is disabled

for FTP/

Desktop)

– ❍

AR-M550/M620/M700 SPECIFICATIONS 3 - 9

: Feb. 9 2004

(7) Functions

Mode Scanner Internet FAX FAX Send

function

1 1

Receive function

Memory

– ❍

transmission Onhook – ❍ Quick online

– ❍

send Direct

– Only in

transmission Automatic

– ❍ A3 → B4,

reduction send

Rotation send Zoom send

❍ (Zooming of fixed size → fixed size

❍

only.)

Recall mode

Error – ❍ Busy ––❍

Number of times/time are set by the key operator.

Book document

❍

send Long document send

File division

❍❍❍

Max. 800mm

❍ –

send Send size limit ❍ No. of

❍ –

Max. 999 items registration items of senders Automatic

– ❍

reception Manual

– ❍

reception Memory

– ❍

receive Fixed size

– ❍

reduction receive Specified size

–

zoom receive Rotation

– ❍

receive Division receive – ❍ Conditions are set by the

key operator.

Duplex receive – ❍ Conditions are set by the

key operator. 2 in 1 receive – Domain/

– ❍ (50 items) – Address specification receive enable

Domain/

– ❍ (50 items) Specified Address specification receive disable Automatic

– ❍

switch of TEL/ FAX

External

– ❍

telephone connection remote Answering

–× (PAT telephone connection

Onhook

A3 → A4,

B4 → A4

number only

(Japan only)

countermeasure)

Mode Scanner Internet FAX FAX Receive function

Transfer function when

– ❍

output is disable

Automatic boot

– ❍

mode

Special functions

Time specification

❍

Poling receive ––❍ Bulletin board

––❍

send

Cover function –– Sender print – ❍ Page division ❍ Page

connection Confidential

– ❍ (F code (Remote machine) Relay

– ❍ (F code broadcast indication Send message × Edge erase ❍ Center erase ❍ Multi shot ❍ (2 in 1) Card shot ❍

Report/ List function

Communication record table

Communication

× ❍

❍

result table Address/

❍

Telephone number table Group table ❍ ID, sender

–

address table

Sender table Confidential

box check table

❍ ×

– ❍

(Integrated

memory box

Interface group table

– ❍

(Integrated

memory box

Program table ❍ Send

reservation table

Memory box table

Memory contents

– ❍ (FAX

mode only)

–

(Error report) Clear notification table

Other PC send – PC-iFAX PC-FAX

system)

into the

table.)

into the

table.)

AR-M550/M620/M700 SPECIFICATIONS 3 - 10

: Feb. 9 2004

(8) Transmission system

Mode Scanner Internet FAX FAX Transmission

time

Modem speed – 33.6kbps → 2.4kbps

Mutual communication

Communication line

ECM – ❍

– Between 2 and 3sec

(Super G3/JBIG)

Between 6 and 7sec

(G3 ECM)

automatic fall back

– Super G3/G3

– Public Switched

Telephone Network

(PSTN), Private

Branch Exchange

(PBX), F net

(9) Record size

Mode Scanner Internet FAX FAX Max. record

width Record size –– A3 – A5,

293mm

11"×17" – 5.5"×8.5"

(10) F code communication

Mode Scanner Internet FAX FAX Sub address – ❍ Pass code – ❍

D. Printer function

Standard for the AR-M550N/M620N/M700N. The Printer expansion kit

AR-P19 is required for the AR-M550U/M620U/M700U.

(1) Platform

IBM PC/AT (or compatible) Macintosh (MacOS8.6 or later (excluding MacOS10.2.2) and AppleTalk applicable)

(2) Support OS

Custom PS Windows 95/98/Me

Windows NT 4.0 Windows 2000 Windows XP

Custom PCL5e/ 6(XL)SPDL2

PPD Windows 95/98/Me

(3) PDL emulation

PCL5e compatible, PCL6 compatible, SPDL2 (Japan only), PostScript3 compatible (option)

(4) ESC/P, ESC/P super

(Japan only)

Emulation ESC/P (VP-1100), ESC/P_super Built-in fonts Japanese: Mincho, Gothic (bitmap)

Windows 95/98/Me Windows NT 4.0 Windows 2000 Windows XP

Windows NT 4.0 Windows 2000 Windows XP Mac OS8.6 – 9.x, 10.1.5 and 10.2 – 10.2.8 (excluding 10.2.2)

ANK: Roman, Sans Serif (Bitmap)

(5) Built-in fonts

The printing system is provided with standard fonts of one type of HP compatible bitmap font and 80 types of Latin outline fonts for PCL.

In addition, by use of the PS expansion kit, 136 types of Latin outline fonts and 5 types of Japanese outline fonts are available.

Bitmap fonts 1 kind of font PCL5 Latin font 80 PCL Latin fonts (SPDL)

Standard built-in fonts PCL Kanji font Option (2 ACT Fonts) PS Latin font 136 Type 1 Latin fonts

PS kanji font 5 Type 1 Kanji Fonts

Bar code font Option

Auxiliary to the PS expansion kit

Auxiliary to the PS expansion kit (Japan only)

(6) Print channel

Support print channel

IEEE1284 parallel port USB USB 1.1: Windows98/98SE/Me/2000/XP only

For NetWare environment PSERVER/RPRINT LPR UNIX LPR/LPD command compatible print

IPP IPP 1.0 conforming print channel PAP: EtherTalk (AppleTalk) FTP Function to print receive data by use of the built-

NetBEUI Microsoft NetBEUI compatible print channel Port9100 Supports TCP port 9100 (Raw port).

IEEE1284 parallel port

PSERVER/RPRINT for NetWare environment

LPR

IPP

PAP: EtherTalk (AppleTalk)

FTP

NetBEUI

Raw Port (Port 9100)

USB2.0

Receives print data via the standard IEEE1284

parallel port.

USB 2.0: Windows 2000 / XP only

Used in NetWare environment.

Print channel in the PSERVER/PRINT mode.

channel

Print channel used in the Macintosh

environment

in FTP server.

(7) Print function

Bar code font (JetCAPS BarDIMM emulation) EZ cluster × PDF/TIFF direct print

❍

(8) Compatibility

PCL 5e compatible PCL5e is aimed to provide compatibility with HP

LaserJet 4050.

A small difference in margin, a difference in

rendering caused by a different font family, the

default, a difference in the transfer function are

not included in the compatibility.

Not all PCL commands are included in the

compatibility. PCL6 compatible PCL6 is aimed to provide compatibility with HP

LaserJet 4050.

A small difference in margin, a difference in

rendering caused by a different font family, the

default, a difference in the transfer function are

not included in the compatibility.

Not all PCL commands are included in the

compatibility.

AR-M550/M620/M700 SPECIFICATIONS 3 - 11

: Feb. 9 2004

PostScript compatible

PostScript is aimed to provide compatibility with Adobe PostScript. A small difference in margin, a difference in rendering caused by a different font family, the default, a difference in the transfer function are not included in the compatibility.

ESX/P and ESC/P Super compatible

ESC/P and ESC/P Super are aimed to provide compatibility with Epson VP-1100. A small difference in margin, a difference in rendering caused by a different font family, the default, a difference in the transfer function are not included in the compatibility.

(9) Environment setting

Setting item General

Default setting Basic setting of printing such as the number of

copies and printing direction.

PCL (SPDL*) setting

PCL (SPDL) symbol setting and font setting

∗ SPDL is for

Japan only. PS setting Setting of print enable/disable in a PS error ESC/P (super) setting

ESC/P font and return code setting

(Japan only)

(10) Windows driver function

a. Frequently used functions

PPD *1

Function PCL5e PCL6 PS

Number of

1 – 999 copies Print direction Vertical/Horizontal

Duplex print Simplex print, duplex print (Left/

Upper/Right binding)

Center binding

Invoice on Letter, Letter on

Ledger, A5 on A4, A4 on A3, B5

on B4, Letter on Letter, Ledger on

Ledger, A4 on A4, A3 on A3, B4

on B4

Binding direction

Simplex print, duplex print (Left/

Upper/Right binding) N-up 2/4/6/8 N-up direction N-up frame

❍/✕

Z/Reverse Z/N/ Reverse N

line

*1: For printing, the PS driver bundled in Windows is required. *2: The PS driver bundled in Windows may differ in specifications

depending on the OS.

b. Paper feed system

Function PCL5e PCL6 PS

Paper size A3/B4/A4/B5/A5/Postcard/Ledger/Legal/Foolscap/

Letter/Executive/Invoice/8K/16K

Paper type Normal paper, letterhead, printed paper, punched

paper, recycled paper, color paper, label sheet, thick paper, OHP, tab paper

User

7 types – definition type Paper feed

Auto paper feed, Tray 1/2/3/4/5, manual feed method Cover paper/

Back cover

❍/✕

Setting of Duplex/Simplex/No print page

(In the case of

Windows XP)

Vertical/Horizontal/ Horizontal rotation (*2) Simplex print, duplex print (Long side/Short side binding) (*2) Yes (2up booklet only) (*2)

–

2/4/6/9/16 (*2) Z (*2)

❍ (Always ❍) (*2)

PPD *1

(In the case of

Windows XP)

–

PPD *1

Function PCL5e PCL6 PS

Insert paper ❍/✕

OHP insert

Setting of Duplex/Simplex/No print ✕, ❍ (White paper), ❍ (Printed paper) –

(In the case of

Windows XP)

–

paper

*1: For printing, the PS driver bundled in Windows is required.

c. Paper exit method

PPD *1

Function PCL5e PCL6 PS

Paper exit destination setting

Center tray Finisher → Tray 1 Finisher → Tray 2 Saddle stitch finisher → Tray 1

(In the case of

Windows XP)

❍ (*2)

Saddle stitch finisher → Tray 2 Saddle stitch finisher → Saddle stitch tray

Staple Finisher

• No staple

• 1 position

• 2 positions

Saddle stitch finisher

• No staple

• 1 position

Offset

• 2 positions

❍/✕ *1: For printing, the PS driver bundled in Windows is required. *2: The PS driver bundled in Windows may differ in specifications

depending on the OS.

d. Exposure

PPD *1

Function PCL5e PCL6 PS

(In the case of

Windows XP) Resolution 600/300dpi 600dpi 600dpi Halftone –

❍/✕ (AR-M550N/U, AR-M620N/U)

– (AR-M700U/N)

Screen Frequency

8.0 to 360.0 in 0.1 steps Screen angle 0.0 to

–

360.0 in 0.1

steps Graphic mode

Luster HP-GL2

Luster vector –

selection Smoothing

❍/✕ (AR-M550N/U, AR-M620N/U)

– (AR-M700U/N)

❍/✕ (AR-M550N/U, AR-M620N/U)

–

(AR-M700U/N: Display only and

no function) Toner save ❍/✕ Ultra fine

photo Black-white

–

– ❍/✕

reversion Mirror image – Horizontal/

Horizontal (*2)

Vertical

Zoom –

25 – 400% (XY

1 – 1000% (*2)

independent)

Fit page ❍/✕ –

*1: For printing, the PS driver bundled in Windows is required. *2: The PS driver bundled in Windows may differ in specifications

depending on the OS.

AR-M550/M620/M700 SPECIFICATIONS 3 - 12

: Feb. 9 2004

e. Font

PPD *1

Function PCL5e PCL6 PS

Download

system which

Bitmap, TrueType Bitmap,

can be selected

Type 1, TrueType

(In the case of

Windows XP) Auto, Outline, Bitmap, Native TrueType (*2)

*1: For printing, the PS driver bundled in Windows is required. *2: The PS driver bundled in Windows may differ in specifications

depending on the OS.

f. Other functions

PPD *1

Function PCL5e PCL6 PS

Units composition

❍

(In the case of

Windows XP)

setting Watermark ❍

❍

(Limitations on

functions) Overlay ❍ – Print hold ❍ – Job retention ❍ – Sample print ❍ – Print department

❍ –

management User setting ❍ – Option auto setting ❍ – Job complete

❍ –

notification Tandem print ❍ Carbon print ❍ – Enlargement

–

continuous copy Vertical/horizontal

– ❍ –

independent magnification ratio

Cover insertion +center

❍ –

binding Document filing ❍

–

*1: For printing, the PS driver bundled in Windows is required.

(11) Macintosh driver functions

a. Frequently used functions

Function

(in the case of Mac OS X Ver.10.2.8) Number of copies 1 – 999 Print direction

Duplex print

Vertical/Horizontal/Horizontal rotation (*1) Simplex print, duplex print, pamphlet (Left/

Right/Upper binding) Center binding ❍ N-up N-up direction

N-up frame line

2/4/6/9/16 (*1)

Z/Reverse Z/N/Reverse N (*1)

None / Single Hairline / Single Thinline / Double

Hairline / Double Thinline (*1)

*1 : The PS driver bundled in Macintosh may differ in specifications

depending on the OS.

b. Paper feed method

Function

(in the case of Mac OS X Ver.10.2.8)

Paper size A3/B4/A4/B5/A5/Postcard/Ledger/Legal/

Foolscap/Letter/Executive/Invoice/8K/16K Paper type setting Normal paper/Letter head/Printed paper/

Punched paper/Recycled paper/Color paper/

Label paper/Heavy paper/OHP/Tab paper

Macintosh PPD

Function

User definition type –

(in the case of Mac OS X Ver.10.2.8)

Macintosh PPD

Paper feed method Auto paper feed, Tray 1/2/3/4/5, manual feed Paper feed tray of

the first page

Cover paper/Back cover paper/Insert paper

❍/✕ (*1)

–

(OS9 only: None/before document/after document) (*1)

OHP insert paper ✕, ❍ (White paper), ❍ (Printed paper)

*1: The PS driver bundled in Macintosh may differ in specifications

depending on the OS.

c. Paper exit method

Function

Paper exit destination setting

(in the case of Mac OS X Ver.10.2.8)

Center tray

Macintosh PPD

Finisher Tray 1 Tray 2 Saddle stitch finisher Tray 1 Tray 2 Saddle stitch tray

Staple Finisher

• No staple

• 1 position

• 2 positions

Saddle stitch finisher

• No staple

• 1 position

Offset

• 2 positions ❍/✕

d. Exposure

Function

(in the case of Mac OS X Ver.10.2.8)

Macintosh PPD

Resolution 600dpi Half tone

–

Graphic mode selection – Smoothing

❍/✕ (AR-M550N/U, AR-M620N/U)

– (AR-M700N/U) Toner save ❍/✕ Ultra fine photo

❍/✕ (AR-M550N/U, AR-M620N/U)

– (AR-M700N/U) Black-white reversion

Mirror image Zoom Fit page

–

1-100000 (*1)

–

*1 : The PS driver bundled in Macintosh may differ in specifications

depending on the OS.

e. Font

Function

Download system which can be selected

(in the case of Mac OS X Ver.10.2.8)

–

(Selection allowed only with Mac OS9

Macintosh PPD

(LaserWriter)) (*1)

*1: The PS driver bundled in Macintosh may differ in specifications

depending on the OS.

f. Other functions

Function

(in the case of Mac OS X Ver.10.2.8)

Macintosh PPD

Units composition setting ❍ Watermark ❍

Overlay

Print hold ❍ Job retention ❍ (PIN code input enable)

AR-M550/M620/M700 SPECIFICATIONS 3 - 13

: Feb. 9 2004

Function

Sample print ❍ Print department management ❍ User setting – Option auto setting

Job complete notification – Tandem print ❍ Tab print –

Carbon print Enlargement continuous copy – Vertical/horizontal independent

magnification ratio Cover insertion +center

binding

Document filing

(12) Print performance

Model PDL type

AR-M550N/ M550U

AR-M620N/ M620U

AR-M700N/

M700U

* Measurement conditions

Windows PC: Pentium III 1GHz 128MB OS: Windows XP Professional Macintosh PC: PowerPC G3 700MHz 256MB OS: MacOS X

Driver setting: Default Software: Microsoft Office XP

PCL5 (SPDL2)

(in the case of Mac OS X Ver.10.2.8)

– (OS9 only: ❍)

–

Yes (*1)

Word:

script.doc

(jpn) 9 pages

in total

14sec 9sec 28sec

13sec 8sec 24sec

sec sec sec

Macintosh PPD

Excel:

EXCL.xls 3

pages in

total

PowerPoint:

J11.ppt 12

pages in

total

E. Document filing function

(1) Basic function

Document filing capacity

Fixed folder Standard folder

Number of pages for one file

Number of folders which can be formed in the user folder

Number of users which can be registered

(2) Data operation by each function (For S/U models,

temporary saving only.)

Job

Copy ❍❍❍ × Printer ❍❍❍ × Scan to E-mail/FTP ❍

Scan to HDD ❍❍ ×× FAX receive ×××× FAX send ❍ × ❍ × i-FAX receive ××× × i-FAX send ❍ × ❍ × PC FAX/PC i-FAX send

16GB

User folder Temporary

folder Conforms to the large volume document mode.

(Within the HD capacity) Max. 500 folders

Max. 500 users

Each folder in the

standard folder/user

folder

Common

data

❍ × ❍ ×

Max. 20000 pages or 3000 files

Max. 10000 pages or 1000 files

Temporary folder

Confidential

data

Common

data

× ❍ ×

Confidential

data

(3) Data operation contents

A: S/U model alone B: Printer expansion kit (AR-P19) C: Network expansion kit (AR-NS3) D: FAX expansion kit (AR-FX8)

Reprint ❍❍❍❍❍❍ Resend *1 × ❍❍❍❍❍ Delete ❍❍❍❍❍❍ Shift × ❍❍ × ❍❍ Attribute change *2 (Protection from common use, etc.)

File name change ❍❍❍❍❍❍ Folder making (in the user folder) File transfer to the local PC, FTP server Machine HDD occupying rate display Print log display, CSV export

Print data image view × ❍

Retrieval ❍

*1: The resend enable modes (E-mail send, FAX send, internet FAX send, PC-FAX send, PC-i-FAX send) vary depending on the installation condi-

tions of options.

A (S/U model) A+B (M/N model) A+C (+B) A+D A+B+D A+B+C+D

❍

(Protection from

common use <>

only)

× ❍❍ × ❍❍

× ❍❍ ××❍

× ❍❍ × ❍❍

× ❍

(Enable only on the

(Simple)

❍❍❍

(Protection from

common use <>

only)

Web)

❍

(Simple)

(Enable only on the

❍

Web)

❍

(Enable only on the

Web)

❍

(Simple)

× ❍

(Enable only on the

× ❍

(Enable only on the

❍

(Simple)

❍❍

(Enable only on the

Web)

(Enable only on the

Web)

❍

(Simple)

❍

Web)

❍

Web)

❍

(Simple)

AR-M550/M620/M700 SPECIFICATIONS 3 - 14

: Feb. 9 2004

*2: Attribute change: The file attribute is changed from “Common” to “Protection”/“Confidential”, etc.

(4) Upper limit value of the storable file, folder, and user

The number of files storable in the standard folder and the user folder The number of files storable in the temporary storage folder The number of files storable in the

Max. 3,000 files or 20,000 pages

Max. 1,000 files or 10,000 pages

Max. 500 folders

5. Ambient conditions

A. Space required

(1) Area required

Main unit 1263 × 679mm With full options 2163×691.5mm (With the AR-LC6, AR-F15, AR-

user folder Number of users which can be

Max. 500 users

registered

4. Safety and environmental protection

B. Operating ambient conditions

(1) Temperature/Humidity

Humidity

standards

A. Safety standards

Item Standard

Safety standards Electric safety regulations

UL CSA CE (SEMKO) GB4943

Environmental standards (EMC)

VCCI Class B FCC Class B CISPR22 B GB9254-1998 CLASSB GB17625.1-1998 GB17625.2-1999

GB/T17618-1998 Line standards (When the FAX expansion board is installed.)

Technical standard conformity

acknowledgement (Telecommunications

Business Law)

FCC part 68

ICCS-03

ECCTR-21

A-Tick

B. Environmental standards

(1) Power consumption and environmental standards

Standard International energy program complex machine (EPS) Environmental Choice Program (ECP) Conforms to New Blue Angel. Nordic swan (Sharp: Follows the Green Product Declaration.)

(2) Ozone level

Max. 0.02mg/m³

(3) Noise level

Model Operating Standby AR-M550N/M550U 7.3B or less 5.5B or less AR-M620N/M620U 7.3B or less 5.5B or less AR-M700N/M700U 7.3B or less 5.5B or less

(2) Power supply voltage and frequency

Power supply voltage Rated voltage ± 10% Power supply frequency Rated frequency ± 2%

C. Ambient storage conditions

80%

20%

Humidity

90%

10%

Humidity

90%

20%

F16, AR-CF2 installed)

30˚C, 80%

35˚C, 60%

15˚C 35˚C

Temperature

Main unit

40˚C, 90%

–10˚C50˚C

Consumable items (unopened)

Temperature

40˚C, 90%

50˚C, 60%

AR-M550/M620/M700 SPECIFICATIONS 3 - 15

–5˚C40˚C

Temperature

: Feb. 9 2004

D. Ambient conditions for transporting

Humidity

RH 90%

20%

Main unit

30˚C, 90%

45˚C, 60%

20˚C45˚C

Humidity

90%

10%

–10˚C40˚C

Temperature

Consumable items

40˚C, 90%

Temperature

E. Standard temperature and humidity

Temperature 20 to 25°C Humidity

65 ± 5% RH

6. Service related items

Device cloning ❍ Address book send/ receive tool Humidifier heater SEC only (Standard provision for Japan

RIC Telephone line RIC terminal available

Coin vendor terminal ❍ Card counter Angle/Harness parts supply Key counter (SF-71A/B) Mechanical counter Conforming to 7-digit OEM

❍

model) (Supplied as a service part)

E-mail RIC available (Conforming to soft key.)

Only the harness is left.

For SHARP (Parts support)

AR-M550/M620/M700 SPECIFICATIONS 3 - 16

: Feb. 9 2004

[4] CONSUMABLE PARTS

1. Supply system table

A. USA, Canada, South and Central America

No. Part name Content Life Model name Packing Remark

1 Toner cartridge (Black) Toner cartridge (Black)

(Toner; Net weight 1430g) With IC chip

Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip

2 Developer (Black)

3 Drum OPC drum x 1 62/70ppm: 300k

Developer (Black) (Developer; Net weight 725g)

B. Europe affiliates (Including East Europe, Russia)/Australia/New Zealand/UK)

No. Part name Content Life Model name Packing Remark

1 Toner cartridge (Black) Toner cartridge (Black)

(Toner; Net weight 1430g) With IC chip

Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip

2 Developer (Black) Developer (Black)

3 Drum OPC drum x 1 62/70ppm: 300k

(Developer; Net weight 725g)

C. Asia affiliates

No. Part name Content Life Model name Packing Remark

Toner cartridge (Black)

Developer (Black)

Drum OPC drum

Toner cartridge (Black) (Toner; Net weight 1430g) With IC chip Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip

Developer (Black) (Developer; Net weight 725g)

x 10 720k (72k x 10) AR-620MT 1 * Life setting by A4/LT

6% document

MT = NT x 10

x 10 830k (83k x 10) AR-621MT

x 10 62/70ppm: 300k

55ppm: 250k

x 10 720k (72k x 10) AR-620LT 1 * Life setting by A4/LT

x 10 830k (83k x 10) AR-621LT

x 10 62/70ppm: 300k

55ppm: 250k

x 10 720k (72k x 10) AR-620CT 1 * Life setting by A4/LT

x 10 830k (83k x 10) AR-621CT

x 10 62/70ppm: 300k

55ppm: 250k

x 1 62/70ppm: 300k

55ppm: 250k

AR-620MD 1 Used two bags.

AR-620DR 10

AR-620LD 1 Used two bags.

AR-620DM 10

AR-620CD 1

AR-620DR 10

MD = ND x 10

6% document

LT = T x 10

LD = DV x 10

6% document

CT = ST x 10

Used two bags. CD = SD x 10

D. Hong Kong

No. Part name Content Life Model name Packing Remark

Toner cartridge (Black) For SRH

Developer (Black)

Drum OPC drum

Toner cartridge (Black) (Toner; Net weight 1430g) With IC chip

Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip Developer (Black) (Developer; Net weight 725g)

x 10 720k (72k x 10) AR-620CT-C 1 * Life setting by A4/

x 10 830k (83k x 10) AR-621CT-C

x 10 62/70ppm: 300k

55ppm: 250k

x 1 62/70ppm: 300k

55ppm: 250k

AR-620CD-C 1

AR-620DR-C 10

LT 6% document

CT-C = ST-C x 10

Used two bags. CD-C = SD-C x 10

E. China (AR-M620N/M700N)

No. Part name Content Life Model name Packing Remark

Toner cartridge (Black)

Developer (Black)

Drum OPC drum

Toner cartridge (Black) (Toner; Net weight 1430g) With IC chip Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip Developer (Black) (Developer; Net weight 725g)

AR-M550/M620/M700 CONSUMABLE PARTS 4 - 1

x 10 72k (72k x 1) AR-621ST-C 1 * Life setting by A4/LT

6% document

x 10 83k (83k x 1) AR-622ST-C

x 10 62/70ppm: 300k AR-620SD-C 1 Used two bags.

x 1 62/70ppm: 300k AR-620DR-C 1

: Feb. 9 2004

F. Middle East/Philippine

No. Part name Content Life Model name Packing Remark

1 Toner cartridge (Black) Toner cartridge (Black)

(Toner; Net weight 1430g) With IC chip Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip

2 Developer (Black) Developer (Black)

(Developer; Net weight 725g)

3 Drum OPC drum x 1 62/70ppm: 300k

x 10 720k (72k x 10) AR-620ET 1 * Life setting by A4/LT

x 10 830k (83k x 10) AR-621ET

x 10 62/70ppm: 300k

55ppm: 250k

AR-620CD 1 Used two bags.

AR-620DR 10

6% document

ET=FT x 10

CD = SD x 10

G. Taiwan

No. Part name Content Life Model name Packing Remark

1 Toner cartridge (Black) Toner cartridge (Black)

(Toner; Net weight 1430g) With IC chip Toner cartridge (Black) (Toner; Net weight 1650g) With IC chip

2 Developer (Black) Developer (Black)

(Developer; Net weight 725g)

3 Drum OPC drum x 1 62/70ppm: 300k

x 10 720k (72k x 10) AR-620ET 1 * Life setting by A4/LT

6% document

ET=FT x 10

x 10 830k (83k x 10) AR-621ET

x 10 62/70ppm: 300k

55ppm: 250k

AR-620LD 1 Used two bags.

LD = DV x 10

AR-620DM 10

2. Maintenance parts list

A. USA, Canada

No. Name Content

1 Maintenance kit 1 Side seal F x 1 250K 300K 300K AR-620KA 10

Side seal R x 1 MC cleaning unit x 1 Cleaner blade x 1 Drum separation pawl x 4 Screen grid x 1 Toner reception seal x 1 Charging plate x 1 Paper dust removal unit x 1 DV seal x 1 DV side seal F x 1 DV side seal R x 1 Toner filter x 1

2 Maintenance kit 2 Transfer cleaning roller x 1 250K 300K 300K AR-620KB 10

Transfer belt x 1 Transfer roller x 1 Transfer gear x 1

3 Upper heat reoller kit Upper heat roller x 1 250K 300K 300K AR-620UH 10

Fusing separation pawl (Upper) x 6

4 Lower heat roller kit Lower heat roller x 1 250K 300K 300K AR-620LH 10

Fusing separation pawl (lower) x 2

5 Cleaner blade Cleaner blade x 10 250K

6 Cleaning roller kit

(55/62cpm model)

7 Maintenance kit 3

(70cpm model)

8 Heat roller kit Sub heat roller x 1 250K 300K 300K AR-620HR 10

9 DSPF roller kit SPF paper feed roller x 1 100K 100K 100K AR-620DF 10

10 Paper feed roller kit Main unit paper feed roller x 1 100K 100K 100K AR-620RT 10

Scraper unit x 10 250K Sub heat roller cleaning unit x 10 Cleaning sheet x 10 ––300K AR-700CR 1 Oil roller x 10 Cleaning roller bearing x 20 Pressure cleaning plate x 10

Heat roller bearing x 2

SPF take-up roller x 1 SPF reverse roller x 1

Main unit paper feed take-up roller x 1 Main unit paper feed reverse roller x 1

55cpm 62cpm 70cpm

(x 10)

Life

300K (x 10) 300K (x 10)

Model name Packing Remark

300K

(x 10)

AR-620CB 1 AR-620CB =

– AR-620CR 1 AR-620CR =

(AR-620BL) x 10

(AR-620RC) x 10

AR-M550/M620/M700 CONSUMABLE PARTS 4 - 2

: Feb. 9 2004

No. Name Content

11 Staple cartridge Finisher staple x 3 5,000

12 Staple cartridge Saddle finisher staple x 3 2,000

55cpm 62cpm 70cpm

times x 3

Life

5,000

times x 3

2,000

times x 3

5,000

times x 3

2,000

times x 3

Model name Packing Remark

SF-SC11 20 Cartridge for AR-F15

AR-SC3 40 Cartridge for AR-F16

B. Europe affiliates (Including East Europe, Russia) Australia/New Zealand/UK

No. Part name Content

1 Maintenance kit 1 Side seal F x 1 250K 300K 300K AR-620KA 10

2 Maintenance kit 2 Transfer cleaning roller x 1 250K 300K 300K AR-620KB 10

Transfer belt x 1 Transfer roller x 1 Transfer gear x 1

3 Maintenance kit 3

(55/62cpm model)

Maintenance kit 3 (70cpm model)

4 DSPF roller kit SPF paper feed roller x 1 100K 100K 100K AR-620DF 10

5 Paper feed roller kit Main unit paper feed roller x 1 100K 100K 100K AR-620RT 10

6 Staple cartridge Finisher staple x 3

7 Staple cartridge Saddle finisher staple x 3

Upper heat roller x 1 250K 300K – AR-620KC 5 Lower heat roller x 1 Fusing separation pawl (Upper) x 6 Fusing separation pawl (lower) x 4 Scraper unit x 1 Sub heat roller cleaning unit x 1 Sub heat roller x 1 Heat roller bearing x 2 Upper heat roller x 1 ––300K AR-700KC 5 Lower heat roller x 1 Fusing separation pawl (Upper) x 6 Fusing separation pawl (lower) x 4 Cleaning sheet x 1 Oil roller x 1 Cleaning roller bearing x 2 Pressure cleaning plate x 1 Sub heat roller x 1 Heat roller bearing x 2

SPF take-up roller x 1 SPF reverse roller x 1

Main unit paper feed take-up roller x 1 Main unit paper feed reverse roller x 1

55cpm 62cpm 70cpm

5,000

times x 3

2,000

times x 3

Life

5,000

times x 3

2,000

times x 3

5,000

times x 3

2,000

times x 3

Model

name

SF-SC11 20 Cartridge for AR-F15

AR-SC3 40 Cartridge for AR-F16

(Common with the cartridge for AR-F11/ F12)

(Common with the cartridge for AR-F12)

Packing Remark

(Common with the cartridge for AR-F11/ F12)

(Common with the cartridge for AR-F12)

AR-M550/M620/M700 CONSUMABLE PARTS 4 - 3

: Feb. 9 2004

C. Middle East/Asia/South and Central America

No. Part name Content

1 Maintenance kit 1 Side seal F x 1 250K 300K 300K AR-620KA 10

2 Maintenance kit 2 Transfer cleaning roller x 1 250K 300K 300K AR-620KB 10

Transfer belt x 1 Transfer roller x 1 Transfer gear x 1

3 Maintenance kit 3

(55/62cpm model)

Maintenance kit 3 (70cpm model)

4 DSPF roller kit SPF paper feed roller x 1 100K 100K 100K AR-620DF 10

5 Paper feed roller kit Main unit paper feed roller x 1 100K 100K 100K AR-620RT 10

6 Staple cartridge Finisher staple x 3

7 Staple cartridge Saddle finisher staple x 3

SPF take-up roller x 1 SPF reverse roller x 1

Main unit paper feed take-up roller x 1 Main unit paper feed reverse roller x 1

55cpm 62cpm 70cpm

5,000

times x 3

2,000

times x 3

Life

5,000

times x 3

2,000

times x 3

5,000

times x 3

2,000

times x 3

Model name Packing Remark

SF-SC11 20 Cartridge for AR-F15

AR-SC3 40 Cartridge for AR-F16

(Common with the cartridge for AR-F11/ F12)

(Common with the cartridge for AR-F12)

AR-M550/M620/M700 CONSUMABLE PARTS 4 - 4

: Feb. 9 2004

D. China

x 3

Life

5,000 times

2,000 times

Model name Packing Packing

SF-SC11 20 Cartridge for AR-F15

x 3

AR-SC3 40 Cartridge for AR-F16

x 3

No. Part name Content

1 Maintenance kit 1 Side seal F x 1 300K 300K AR-620KA 10

2 Maintenance kit 2 Transfer cleaning roller x 1 300K 300K AR-620KB 10

Transfer belt x 1 Transfer roller x 1 Transfer gear x 1

3 Maintenance kit 3

(55/62cpm model)

Maintenance kit 3 (70cpm model)

4 DSPF roller kit SPF paper feed roller x 1 100K 100K AR-620DF 10

5 Paper feed roller kit Main unit paper feed roller x 1 100K 100K AR-620RT 10

6 Staple cartridge Finisher staple x 3

7 Staple cartridge Saddle finisher staple x 3

Upper heat roller x 1 300K – AR-620KC 5 Lower heat roller x 1 Fusing separation pawl (Upper) x 6 Fusing separation pawl (lower) x 4 Scraper unit x 1 Sub heat roller cleaning unit x 1 Heat roller bearing x 2 Upper heat roller x 1 – 300K AR-700KC 5 Lower heat roller x 1 Fusing separation pawl (Upper) x 6 Fusing separation pawl (lower) x 4 Heat seal plate N assembly x 1 Oil roller x 1 Cleaning roller bearing x 2 Pressure cleaning plate x 1 Sub heat roller x 1 Heat roller bearing x 2

SPF take-up roller x 1 SPF reverse roller x 1

Main unit paper feed take-up roller x 1 Main unit paper feed reverse roller x 1

62cpm 70cpm

5,000 times

2,000 times

(Common with the cartridge for AR-F11/F12)

(Common with the cartridge for AR-F12)

AR-M550/M620/M700 CONSUMABLE PARTS 4 - 5

+ 428 hidden pages