Sharp Aquos LC-32LE700S, Aquos LC-46LE700E, Aquos LC-40LE700E, Aquos LC-40LE700S, Aquos LC-46LE700S Operation Manual
...
LC-32LE700E/LC-32LE700S/
LC-40LE700E/LC-40LE700S/
LC-32LE700E LC-32LE700S
LC-40LE700E LC-40LE700S
LC-46LE700E LC-46LE700S
LC-52LE700E LC-52LE700S
OPERATION MANUAL/BEDIENUNGSANLEITUNG/MODE D’EMPLOI/MANUALE DI
LC-32LX700E LC-40LX700E LC-46LX700E
LC-32LU700E LC-32LU700S LC-40LU700E LC-40LU700S LC-46LU700E LC-46LU700S
LC-32LE705E LC-32LE705S LC-40LE705E LC-40LE705S
LC-46LE705E LC-46LE705S LC-52LE705E LC-52LE705S
LC-32LX705E LC-40LX705E LC-46LX705E
LC-32LU705E LC-32LU705S LC-40LU705E LC-40LU705S LC-46LU705E LC-46LU705S
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISEUR COULEUR À ÉCRAN
CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
TELEVISOR DE CRISTAL LÍQUIDO
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
MANUAL DE OPERAÇÃO
NEDERLANDS
ESPAÑOL
PORTUGUÊS
SPECIAL NOTE FOR USERS IN THE U.K.
ASA
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A
fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
and of the same rating as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied,
cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and
disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a
serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
•
The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
•
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin
plug.
Before replacing the plug cover make sure that:
If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
•
The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
•
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
OPERATION MANUAL
The illustrations and the OSD in this operation manual are for
•
explanation purposes and may vary slightly from the actual
operations.
The examples used throughout this manual are based on the
•
LC-46LE700E model.
•
LC-32LE700E, LC-32LE700S, LC-32LX700E, LC-32LU700E,
LC-32LU700S, LC-40LE700E, LC-40LE700S, LC-40LX700E,
LC-40LU700E, LC-40LU700S, LC-46LE700E, LC-46LE700S,
LC-46LX700E, LC-46LU700E, LC-46LU700S, LC-52LE700E,
LC-52LE700S, LC-32LE705E, LC-32LE705S, LC-32LX705E,
LC-32LU705E, LC-32LU705S, LC-40LE705E, LC-40LE705S,
LC-40LX705E, LC-40LU705E, LC-40LU705S, LC-46LE705E,
LC-46LE705S, LC-46LX705E, LC-46LU705E, LC-46LU705S,
LC-52LE705E and LC-52LE705S models are compatible with
H.264 (MPEG4 H.264, MPEG4 AVC, MPEG4 AVC/H.264)
compressed broadcasts.
•
Only the LC-32LE705E, LC-32LE705S, LC-40LE705E, LC40LE705S, LC-46LE705E, LC-46LE705S, LC-32LX705E,
LC-40LX705E, LC-46LX705E, LC-32LU705E, LC-32LU705S,
LC-40LU705E, LC-40LU705S, LC-46LU705E and LC46LU705S models are compatible with the Common Interface
(CI) standard as well as the enhanced security Common
Interface Plus (CI+) standard.
Dear SHARP customer
Thank you for your purchase of the SHARP LCD colour
TV product. To ensure safety and many years of troublefree operation of your product, please read Important
safety precautions carefully before using this product.
Trademarks
“HDMI, the HDMI logo and High-Definition Multimedia
•
Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
Manufactured under license from Dolby Laboratories.
•
•
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
The “HD TV 1080p” Logo is a trademark of EICTA.
•
The DVB logo is the registered trademark of the Digital
•
Video Broadcasting—DVB—project.
LC_ LCFONT+ and LC logo mark
•
are registered trademarks of SHARP Corporation. This
product is embedded with LC Font technology, which was
developed by SHARP Corporation for clearly displaying
easy-to-read characters on an LCD screen. However, other
non-LCD fonts are used for displaying some screen pages.
ENGLISH
Introduction ................................................................. 2
Important safety precautions ................................. 2
Remote control unit .............................................. 3
TV (front view) ....................................................... 4
TV (rear view) ........................................................ 4
Preparation.................................................................. 5
Supplied accessories ............................................ 5
Attaching the stand unit ........................................ 5
Inserting the batteries............................................ 6
Using the remote control unit ................................ 6
Quick guide ................................................................. 7
Initial installation overview...................................... 7
Before turning on the power ................................. 8
Initial auto installation ............................................ 9
Inserting the CA card into the CI module ............. 11
Watching TV .............................................................. 12
Daily operation .................................................... 12
EPG .................................................................... 13
Teletext ............................................................... 15
Connecting external devices ................................... 16
Video connections .............................................. 16
Audio connections .............................................. 18
AQUOS LINK ............................................................. 19
Controlling HDMI devices using AQUOS LINK ..... 19
AQUOS LINK connection .................................... 19
AQUOS LINK setup ............................................ 20
Operating an AQUOS LINK device ...................... 21
Menu operation......................................................... 22
What is the MENU? ............................................ 22
Basic adjustment ...................................................... 23
Picture settings ................................................... 23
Audio settings ..................................................... 25
Power save settings ............................................ 26
Channel settings ................................................. 27
Password/Parental lock settings ......................... 30
Other basic adjustments ..................................... 30
Useful viewing functions .......................................... 31
Selecting the picture size .................................... 31
Language settings .............................................. 32
Display settings ................................................... 33
Other useful features ............................................... 34
Setting when using external devices ................... 34
Additional features .............................................. 34
Connecting a USB device ................................... 35
USB Photo viewer/Music player .......................... 35
Connecting a PC ....................................................... 37
Connecting a PC ................................................ 37
Displaying a PC image on the screen .................. 37
RS-232C port specifications ............................... 39
Appendix ................................................................... 41
Troubleshooting .................................................. 41
Updating your TV via DVB-T ............................... 42
Reset .................................................................. 42
Identification ....................................................... 42
Updating your TV via USB .................................. 43
Specifications ..................................................... 44
Environmental specifications ............................... 46
End of life disposal .............................................. 48
ENGLISH
1
Introduction
Important safety precautions
Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use
•
liquid cleaners or aerosol cleaners.
Use a soft damp cloth to gently wipe the panel when it is dirty. To protect the panel, do not use a chemical cloth to clean it.
•
Chemicals may cause damage or cracks in the cabinet of the TV.
Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub, swimming pool and
•
in a wet basement.
Do not place vases or any other water-filled containers on this product. The water may spill onto the product
•
causing fire or electric shock.
Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause the product
•
to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod,
bracket or table recommended by the manufacturer or sold with the product. When mounting the product on
a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the
manufacturer.
When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive
•
force and uneven floor surface can cause the product to fall from the cart.
Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or block
•
these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the
product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation
openings. This product is not designed for built-in installation; do not place the product in an enclosed place
such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are
followed.
The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or
•
impact applied. If the LCD panel is broken, be careful not to be injured by broken glass.
Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-
•
generating products (including amplifiers).
To prevent fire, never place any type of candle or naked flames on the top or near the TV set.•
To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.•
Headphones—Do not set the volume at a high level. Hearing experts advise against extended listening at high volume levels.•
Do not display a still picture for a long time, as this could cause an afterimage to remain.•
There is power consumption always if main plug is connected.•
Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous
•
conditions. Request a qualified person to perform servicing.
The LCD panel is a very high technology product, giving you fine picture details.
Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a fixed point of blue, green or
red. This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speakers. Be sure to always carry the TV by two people holding it with two
hands—one hand on each side of the TV.
Devices connected to the protective earthing of the building installation through the MAINS connection or through other devices with a
connection to protective earthing and to a television distribution system using coaxial cable, may in some circumstances create a fire
hazard. Connection to a television distribution system therefore has to be provided through a device providing electrical isolation within a
certain frequency range (galvanic isolator, see EN 60728-11).
NOTE
For requirements in Norway and Sweden, the requirements for isolation are also relevant for devices that can be connected to
•
television distribution systems.
2
Introduction
Remote control unit
B (Standby/On)
1
(Page 12)
Buttons for useful operations
2
m (Teletext)
ATV: Display analogue teletext
(Page 15).
DTV: Select MHEG-5 and teletext
for DTV (Page 15).
k (Reveal hidden teletext)
(Page 15)
[ (Subtitle)
Switch subtitle languages on/off
(Pages 15 and 32).
3 (Freeze/Hold)
Press to freeze a moving image on
the screen.
Teletext: Stop updating teletext
pages automatically or release the
hold mode.
1 (Subpage)
(Page 15)
v (Top/Bottom/Full)
Set the area of magnification in
teletext mode (Page 15).
Numeric buttons 0_9
3
Set the channel.
Enter desired numbers.
Set the page in teletext mode.
When the five Nordic countries
•
(Sweden, Norway, Finland,
Denmark or Iceland) are selected
in the country setting from “Auto
installation” (page 27), DTV
services are four digits. When
another country is selected, DTV
services are three digits.
A (Flashback)
4
Press to return to the previously
selected channel or external input.
DTV
5
Press to access digital TV mode.
ATV
6
Press to access conventional
analogue TV mode.
2 (Sound mode)
7
Select a sound multiplex mode
(Page 12).
i+/- (Volume)
8
Increase/decrease TV volume.
e (Mute)
9
TV sound on/off.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
f (WIDE MODE)
0
Select a wide mode (Pages 31
and 37).
#
Q
Select a video setting (Page 24).
a/b/c/d (Cursor)
W
Select a desired item on the setting
screen.
;
Execute a command within the
“MENU” screen.
ATV/DTV: Display the programme
list when no other “MENU” screen
is running.
15
16
17
18
19
20
21
22
23
24
25
>
E
Exit the “MENU” screen.
R/G/Y/B (Colour) buttons
R
The coloured buttons are
correspondingly used to select the
coloured items on the screen (e.g.,
EPG, MHEG-5, teletext).
b (INPUT SOURCE)
T
Select an input source (Page 12).
EPG
Y
DTV: Display the EPG screen
(Pages 13_14).
RADIO
U
DTV: Switch between radio and
data mode.
When only data broadcasting
•
(no radio broadcasting) is
transmitted by DVB, the radio
broadcasting will be skipped.
P. INFO
I
Press to display programme
information which is transmitted
through digital video broadcasting in
the upper left corner of the screen
(DTV only).
:r/s
O
Select the TV channel.
p (Display information)
P
Press to display the station
information (channel number, signal,
etc.) in the upper right corner of the
screen (Page 33).
ECO (Standard/Advanced/Off)
A
Select “Energy save” setting (Page
26).
@
S
“MENU” screen on/off.
6 (Return)
D
Return to the previous “MENU”
screen.
SLEEP
F
Press to schedule a time for the TV
to automatically standby (Page 26).
AQUOS LINK buttons
G
If external equipment such as a
AQUOS BD player is connected via
HDMI cables and is AQUOS LINK
compatible, you can use these
AQUOS LINK buttons. See pages
19 and 21 for details.
3
Introduction
TV (front view)
TV (rear view)
1
2
3
4
5
1
Blue illumination LED
2
B (Standby/On indicator)
6
2 3 45
7
8
1
9
10
6
*1
7
8
9
11
10
12
*2
13
14
15
3
OPC indicator
4
Remote control sensor
5
OPC sensor
6
a (Power button)
7
@ (Menu button)
8
b (Input source button)
9
:r/s (Programme [channel]
buttons)
i+/- (Volume buttons)
10
COMMON INTERFACE slot
1
USB terminal
2
HDMI 4 (HDMI) terminal
3
EXT 9 (VIDEO/AUDIO) terminals
4
Headphones
5
AC INPUT terminal
6
MAIN POWER switch
7
HDMI 3 (HDMI) terminal
8
HDMI 1 (HDMI) terminal
9
EXT 4 (ANALOGUE RGB (PC))
10
terminal
Antenna terminal
11
HDMI 2 (HDMI) terminal
12
HDMI 2/PC AUDIO (R/L) jack
13
DIGITAL AUDIO OUTPUT
14
terminal
RS-232C terminal
15
EXT 3 (COMPONENT/AUDIO)
16
terminals
EXT 1 (RGB) terminal
17
EXT 2 (AV) terminal
18
OUTPUT (AUDIO) terminals
19
WARNING
Excessive sound pressure from earphones
•
and headphones can cause hearing loss.
•
Do not set the volume at a high level.
Hearing experts advise against extended
listening at high volume levels.
16 17 18 19
When the MAIN POWER switch is turned off (a), the amount of electric power consumed will be reduced to 0.01 W or less. However,
I
unlike when unplugging the AC cord, the power is not completely disconnected.
J
The HDMI 2 and EXT 4 terminals can both use the same audio input terminal (HDMI 2/PC AUDIO (R/L)). However, the proper item must
be selected in the “PC audio select” menu (refer to page 25 for details).
4
Preparation
Supplied accessories
Remote control unit ( x 1) AC cord ( x 1) Cable clamp ( x 1) Stand unit ( x 1)
For 32 inch models
Product shape varies in
For 40/46/52 inch models
some countries.
Pages 3 and 6 Page 8 Page 8 Page 5
Operation manual (this publication)
•
“AAA” size zinc-carbon battery ( x 2) ... Page 6
•
Attaching the stand unit
Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
•
Before performing work, spread cushioning over the surface on which you will be laying the TV. This will prevent it from being damaged.
•
CAUTION
Attach the stand in the correct direction.
•
Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
•
Confirm that there are eight screws with the
1
stand unit.
Models Screws
32 inch models
AB
40/46/52 inch models
CD
Inserting the stand.
3
Insert the stand into the openings on the
1
bottom of the TV (hold the stand so it will not
drop from the edge of the base area).
2
Insert and tighten the four screws into the four
holes on the rear of the TV.
2 2
Attach the supporting post for the stand unit
2
onto the base using the four screws with the
screw driver as shown.
*
32 inch models: Use Screws B in the table in step 1.
*
40/46/52 inch models: Use Screws D in the table in step 1.
*
Supporting
post
Soft cushion
1
1
32 inch models: Use Screws A in the table in step 1.
*
40/46/52 inch models: Use Screws C in the table in step 1.
*
NOTE
To detach the stand unit, perform the steps in reverse order.
•
A screw driver is not supplied with this product.
•
The stand base is made of glass. Therefore, be careful not to
•
drop the stand base or apply pressure to it.
•
Do not place heavy objects on the stand base.
5
Preparation
Inserting the batteries
Before using the TV for the first time, insert two supplied “AAA” size zinc-carbon batteries. When the batteries become
depleted and the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Open the battery cover.
1
2
Insert two supplied “AAA” size zinc-carbon
batteries.
Place batteries with their terminals corresponding to the (e)
•
and (f) indications in the battery compartment.
Close the battery cover.
3
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
Do not mix batteries of different types. Different types of batteries have different characteristics.
•
Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old
•
batteries.
•
Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage,
wipe thoroughly with a cloth.
•
The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
•
If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
•
When replacing the batteries, use zinc-carbon batteries instead of alkaline ones.
Note on disposing batteries
The batteries provided contain no harmful materials such as cadmium, lead or mercury.
Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household rubbish.
Deposit any used batteries free of charge into the designated collection containers set up at commercial businesses.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control unit
and sensor may prevent proper operation.
5 m
Remote control sensor
Cautions regarding the remote control unit
Do not expose the remote control unit to shock. In addition, do not expose the remote
•
control unit to liquids, and do not place in an area with high humidity.
Do not install or place the remote control unit under direct sunlight. The heat may cause
•
deformation of the unit.
The remote control unit may not work properly if the remote control sensor of the TV is
•
under direct sunlight or strong lighting. In such cases, change the angle of the lighting or
the TV, or operate the remote control unit closer to the remote control sensor.
6
Quick guide
Initial installation overview
Follow the steps below one by one when using the TV for the first time. Some steps may not be necessary depending
on your TV installation and connection.
Run the
Preparation
Connect an antenna cable to the
antenna terminal (Page 8).
If necessary, insert a CA
card into the CI slot to watch
scrambled broadcasts (Page 11).
initial
settings
Turn on (;) the MAIN POWER
switch on the left side of the TV
(Page 4).
The factory default for the MAIN
•
POWER switch is set to on (;).
Turn on the power using a on
the TV (Page 12).
Run the initial auto installation
(Page 9).
Watch TV
Congratulations!
Now you can watch TV.
If necessary, adjust the antenna
to attain maximum signal
reception (Page 11).
Connect external
devices
Connect external devices
such as a DVD player/
recorder as instructed (Pages
16_18).
Connect the AC cord to the TV
(Page 8).
Product shape varies in some
countries.
Language setting
✔
Home/Store setting
✔
STORE
✔
Austria
Finland
Greece
✔
HOME
Country setting
Channel search
setting
Digital search
Analogue search
Start searching
channels
Connect external audio
devices such as speakers/
amplifier as instructed (Page
18).
7
Quick guide
Before turning on the power
1
2
Cable clamp (bundle the cables with the clamp)
Standard DIN45325 plug (IEC 169-2) 75 q coaxial cable
Turn on (;) the MAIN POWER switch on the left side of the TV.
AC cord (product shape varies in some countries)
The AC cord is supplied either with a ferrite core or without a ferrite core. Neither type
*
causes unnecessary electrical wave emissions or interference.
Place the TV close to the AC outlet,
and keep the power plug within
reach.
Supplying power to the antenna
You must supply power to the antenna in order to receive digitally/terrestrially broadcast stations after connecting
the antenna cable to the antenna terminal on the rear of the TV.
Press @ and the “MENU” screen displays.
1
Press c/d to select “Setup”.
2
Press a/b to select “Antenna setup-DIGITAL”, and then press ;.
3
Press a/b to select “Supply voltage”, and then press ;.
4
Press c/d to select “On”, and then press ;.
5
*
Mounting the TV on a wall
This TV should be mounted on a wall only with the wall mount bracket and attachment* available from SHARP (Page 46).
•
The use of other wall mount brackets may result in an unstable installation and may cause serious injuries.
Mounting the LCD colour TV requires special skills and should only be performed by qualified service personnel. Customers
•
should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting that
results in accident or injury.
You can ask qualified service personnel about using an optional bracket and attachment* to mount the TV to a wall.
•
When you mount the TV on a wall, you should attach the supporting post.
•
Only for 40 inch models.
*
8
Quick guide
Initial auto installation
When the TV is powered on for the first time after
purchase, the initial auto installation wizard appears.
Follow the menus and make the necessary settings one
after another.
Confirm the following before turning on
the power
Is the antenna cable connected?
E
Is the AC cord plugged in?
E
Is the MAIN POWER switch turned on (;)?
E
Press a on the TV.
1
2
3
The initial auto installation wizard appears.
•
Setting the OSD language.
Press a/b/c/d to select the desired language,
and then press ;.
Selecting the location of the TV.
HOME
STORE
NOTE
If you set “Sweden” in the country setting, you can select
•
the cable provider “ComHem”. Refer to the H mark
in the following steps or instructions about the settings for
“ComHem”.
Starting channel search.
5
Digital search
Analogue search
Press c/d to select “Digital search” or “Analogue
search”, and then press ;.
To watch both analogue broadcasts and digital
•
broadcasts, you should perform the auto installation
setting for each format (Page 27).
•
If you want to search for more broadcasts, execute
“Additional search” from the “Programme setup” menu
(Pages 27_29).
NOTE
•
If you turn off the power on the TV while performing a channel
search, the initial auto installation wizard will not appear. The
auto installation function allows you to execute the installation
again from the “Setup” menu (Page 27).
•
The initial auto installation wizard will abort if you leave the TV
unattended for 30 minutes before searching for channels.
•
After initial auto installation is completed, the default PIN is
automatically set to “1234”. To change the PIN setting, refer to
Password/Parental lock settings (Page 30). To clear the PIN
setting (PIN input will no longer be needed), refer to CLEARING
THE PIN (Page 41).
•
When “Italy” is selected in the country setting, the default age
restriction value is set to 18.
Press c/d to select where you will use this TV,
and then press ;.
HOME: “STANDARD” will be the default value for the “AV
•
MODE” setting.
•
STORE: “DYNAMIC (Fixed)” will be the default value for
the “AV MODE” setting. If the “AV MODE” is changed,
the TV will automatically switch back to “DYNAMIC
(Fixed)” when there is no signal input from the TV or
remote control unit for 30 minutes.
•
A demonstration image will be displayed after initial auto
installation is completed. If you have chosen “STORE” by
mistake, go to “Setup” > “Reset” > select “HOME” again.
Setting the country.
4
Austria
Finland
Greece
Press a/b/c/d to select your country or area,
and then press ;.
This setting screen only appears during the first
•
installation.
Digital broadcast setting
Press c/d to select “Terrestrial” or “Cable”,
and then press ;.
Terrestrial
H
•
When you set “Sweden” in the country setting and select
“Cable” for the searching format, you can select the
cable provider “ComHem”.
Searching for terrestrial broadcasts
E
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
•
Cable
9
Quick guide
Searching for cable broadcasts
E
To change each item to the appropriate
settings:
Press a/b to select the menu, and then
1
press ;.
Scrambled stations [Yes]
Search method
Start frequency
Network ID
Symbol rate 1
Symbol rate 2
QAM modulation 1
QAM modulation 2
Reset
Search start
2
Press a/b/c/d or 0_9 to select or input
the appropriate item/value, and then press
;.
3
Press a/b to select “Search start”, and then
press ;.
4
The TV searches for, sorts and stores all
the receivable TV stations according to their
settings and the connected antenna.
•
To abort the initial auto installation in progress, press 6.
H
•
The “Scrambled stations” menu and the “Search method”
menu are not displayed on the screen as each menu item is
fixed.
•
The value of “Start frequency” and “Network ID” should be set
to the value specified by the cable provider.
[Channel]
[None]
Menu Description Selectable items
Scrambled
stations
Search
method
Start
frequency
Network ID
Symbol
rate 1*
Symbol
rate 2*
QAM
modulation 1
QAM
modulation 2
*
Set up “Symbol rate 2” if the cable provider uses several
symbol rates.
Specifies if you
need to add pay-TV
services.
Specifies how you
search channels.
Specifies the network.
Set this to register
only the specified
network ID without
registering any special
services.
The symbol rates
are specified by the
cable provider. Input
the value received for
CATV.
The symbol rates
are specified by the
cable provider. Input
the value received for
CATV.
Yes, No
Channel: Extracts all
of information from a
channel (quick, but
needs corresponding
TV stations).
Frequency: Checks
every frequency in
range (slow).
From 47.0_858.0
MHz
None, 0_65535
1000_9000
1000_9000
16, 32, 64, 128, 256
None, 16, 32, 64,
128, 256
H
When you set “Sweden” in the country setting and select
•
“Cable” for the searching format, you can select the cable
provider “ComHem”. Follow the screen prompts.
10
Analogue broadcast setting
The TV searches for, sorts and stores all the
receivable TV stations according to their
settings and the connected antenna.
To abort the initial auto installation in progress, press 6.
•
Quick guide
Checking signal strength and
channel strength (DVB-T/C)
If you install a DVB-T/C antenna for the first time or
relocate it, you should adjust the alignment of the
antenna to receive a good reception while checking the
antenna setup screen.
Go to “MENU” > “Setup” > “Antenna setupDIGITAL”.
Checking signal strength
E
Press a/b to select “Signal strength”, and
then press ;.
Supply voltage
Signal strength
Channel strength
E
Checking channel strength
Press a/b to select “Channel strength”, and
then press ;.
You can input a specified frequency band using the 0_9
•
numeric buttons.
CH no.
Signal strength
Current Max.
Quality
Current Max.
Channel strength of DVB-T
Supply voltage
Signal strength
Channel strength
CH no.
Signal strength
Current Max.
Quality
Current Max.
MHz
Channel strength of DVB-C
Supply voltage
Signal strength
Channel strength
Position and align the antenna so that
4
Frequency
Symbol rate
QAM modulation
Signal strength
Current
Quality
Current Max.
Max.
the maximum possible values for “Signal
strength” and “Quality” are obtained.
NOTE
The values of “Signal strength” and “Quality” indicate when to
•
check the appropriate alignment of the antenna.
MHz
Inserting the CA card into the CI module
In order to receive coded digital stations, a common interface module (CI module) and a CA card must be inserted in the
CI slot of the TV.
Checking CI module information
Go to “MENU” > “Digital setup” > “CI menu”.
This menu is only available for digital stations.
•
The content of this menu depends on the provider of the CI module.
•
Module
Carefully insert the CI module in
1
the CI slot with the contact side
forward.
The logo on the CI module must
2
be facing outward from the rear
of the TV.
NOTE
Only the LC-32LE705E, LC-32LE705S, LC-40LE705E, LC-40LE705S, LC-46LE705E, LC-46LE705S, LC-32LX705E, LC-40LX705E, LC-
•
46LX705E, LC-32LU705E, LC-32LU705S, LC-40LU705E, LC-40LU705S, LC-46LU705E and LC-46LU705S models are compatible with
the Common Interface (CI) standard as well as the enhanced security Common Interface Plus (CI+) standard.
It takes about 30 seconds to certify the license key when you insert a CA card into the CI+ compatible CI module for the first time. This
•
process may fail when there is no antenna input or you have never run “Auto installation”.
The CI+ compatible CI module sometimes upgrades its firmware. You may not receive any TV images before upgrading. You can only use
•
the power button during upgrading.
The CI+ compatible CI module does not allow you to output any copy protected programmes using monitor out. In this case, the copy
•
protect icon* is shown in the programme information when P. INFO is pressed.
Protect icon: X
*
If the TV displays an update confirmation message for the CA card while receiving CI+ compatible broadcasts, follow the screen prompts.
•
Make sure that the CI module is properly inserted.
•
General information on CI module displays.
Menu
Adjustment parameters of each CA card displays.
Enquiry
You can input numerical values such as passwords here.
11
Watching TV
Daily operation
Switching on/off
Turning on/off the power
Turn on (;) the MAIN POWER switch on the
1
left side of the TV (Page 4).
Press a on the TV.
2
Switch it off by pressing a on the TV.
When turning off the power using a on the TV, EPG data
•
will be lost.
Standby mode
To standby mode
E
If the TV is switched on, you can switch it to standby by
pressing B on the remote control unit.
E
Switching on from standby
From standby, press B on the remote control unit.
TV indicator status
B (Standby/On
indicator)
Off
Green
Red
Power off
Power on
Standby
Status
NOTE
If you are not going to use this TV for a long period of time, be
•
sure to remove the AC cord from the AC outlet or turn off (a)
the MAIN POWER switch on the left side of the TV (Page 4).
•
A small amount of electric power is still consumed even when
a is turned off.
Switching between digital and
analogue broadcasts
Watching digital
broadcasts
Watching analogue
broadcasts
Changing channels
Selecting an external video
source
Once the connection is made,
press b to display the “INPUT
SOURCE” screen, and then press
b or a/b to switch over to
the appropriate external source
with ;.
INPUT SOURCE
TV
EXT 1
EXT 2
EXT 3
Selecting a sound mode
DTV mode
E
If multi sound modes are received, each time you press
2 the mode switches as follows.
Audio (ENG) STEREO
L/R LRLR
Audio (ENG) CH A
CH A CH B CH AB
Audio (ENG) MONO
Press c/d to select L or R sound when the STEREO or
DUAL MONO screen is displayed.
Audio (ENG) STEREO
L/R LRLR
NOTE
The sound mode screen disappears in six seconds.
•
Selectable items vary depending on the received broadcasts.
•
ATV mode
E
Each time you press 2, the mode switches as shown
in the following tables.
NICAM TV broadcasts selection
Signal Selectable items
Stereo
Bilingual
Monaural
Signal Selectable items
Stereo
Bilingual
Monaural
NICAM STEREO, MONO
NICAM CH A, NICAM CH B, NICAM CH AB,
MONO
NICAM MONO, MONO
A2 TV broadcasts selection
STEREO, MONO
CH A, CH B, CH AB
MONO
With :r/s With 0_9
12
NOTE
•
When no signal is input, the sound mode will display “MONO”.
Watching TV
EPG
EPG is a programme list that is displayed on the screen. With the EPG, you can check the schedule of DTV/RADIO/
DATA, view detailed information about them, tune to an event currently on-air.
Useful settings for using EPG
Basic operation
Press @ and the “MENU” screen
1
displays.
Press c/d to select “Digital setup”.
2
Press a/b to select “EPG setup”, and then
3
press ;.
Digital setup
REC picture size [16:9 TV]
Download setup [Yes]
EPG setup
Subtitle
CI menu
Press a/b to select the desired item, and
4
then press ; (e.g., “EPG setup”, “Display
range setup”, etc.).
EPG setup
Display range setup
Genre icon setup
Press a/b/c/d to select or adjust the
5
Receive broadcasting EPG
automatically?
Yes No
desired item, and then press ; (e.g., “Yes”,
“No”, etc.).
EPG display settings
EPG setup (setting for receiving EPG
E
data)
If you want to use the EPG for digital stations, select
“Yes”. The EPG data must be automatically captured
while the TV is in standby mode. After setting to “Yes”,
it may take some time to turn off the power using the
remote control unit due to the process of the data
capture.
NOTE
If the MAIN POWER switch or the power button on the TV are
•
switched off, the EPG data will not be captured.
Display range setup
E
The “Display range setup” allows you to select three
types of time spans for display on the screen.
Item
Mode 1 (Wide
angle)
Mode 2 (Zoom)
Mode 3 (Vertical
angle)
E
Genre icon setup
You can grey out or place a mark on desired genres and
smoothly search for programmes you frequently watch.
Displays six hours of programme
information.
Displays three hours of programme
information.
Changes to the EPG display format with
a vertical time span.
E
Genre icon list
Icon Genre Icon Genre
Movie/Drama Music/Ballet/Dance
News/Current
affairs
Show/Game show
Sports
Children’s/Youth
programmes
Arts/Culture
(without music)
Social/Political
issues/Economics
Education/Science/
Factual topics
Leisure hobbies
13
Watching TV
Selecting a programme using EPG
Basic operation
The illustrations on this page are explained
using three digit services.
Display/Close the EPG
E
screen
Press EPG.
Select a programme
E
Select
2
AM PM
Programme info. Search by genre Search by date
Enter Back Exit
Select the desired programme
1
Select the time span
Press a/b to select the desired programme.
•
Press c/d to select the time span you want
to search.
Continue to press d to display programmes in the next
•
time span.
Useful functions
Check programme information
3
1
Press a/b/c/d to select the programme you want to check.
2
Press R, and then press ; to tune to the selected programme.
Search a programme in a category
4
1
Press G.
2
Press a/b to select the desired genre, and then press ;.
3
Press a/b to select a programme you want to watch, and then press
;.
Refer to page 13 for the genre setting.
•
5
Search for a programme by date/time
1
Press Y.
2
Press c/d to select the desired time span, and then press ;.
If a or b are displayed on the left of the services,
continue to press a/b to display next or previous
screen.
Movie/Drama
News/Current affairs
Show/Game show
Sports
Children’s/Youth programmes
Music/Ballet/Dance
Search by time
0 AM - 6 AM 6 AM - 0 PM 0 PM - 6 PM 6 PM - 0 AM
3
Press a/b to select the desired programme, and then press ;.
14
Tod ay
Back to EPGEnterSelect time
Enter +1 Week Next
Next
Loading...