Sharp Aquos LC-13C3U, Aquos LC-15C3U, Aquos LC-20C3U, LC-13C3US, LC-15C3US Operation Manual

LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA

DE CRISTAL LÍQUIDO

TELEVISOR DE CRISTAL

LÍQUIDO

LC-13C3U
LC-15C3U
LC-20C3U

OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE OPERACIÓN
MANUAL DE OPERAÇÃO

ENGLISH

FRANÇAIS

ESPAÑOL

PORTUGUÊS

LC-13C3U
LC-15C3U
LC-20C3U

LIQUID CRYSTAL TELEVISION

OPERATION MANUAL

ENGLISH

ENGLISH

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK.
DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrow­head symbol, within an equilat­eral triangle, is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.

The exclamation point within a
triangle is intended to alert the
user to the presence of impor­tant operating and maintenance
(servicing) instructions in the
literature accompanying the
product.

IMPORTANT:
To aid reporting in case of loss or theft, please
record the TV’s model and serial numbers in the
space provided. The numbers are located at the
rear of the TV.

U.S.A. ONLY

Model No.:

Serial No.:

2

IMPORTANT INFORMATION (Continued)

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF

PLUG TO WIDE SLOT, FULLY INSERT.

U.S.A. ONLY

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.
Disposal of these materials may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the Electronic Industries Alliance:
www.eia.org

3

DEAR SHARP CUSTOMER

Thank you for your purchase of the Sharp LCD Color TV product. To ensure safety and
many years of trouble-free operation of your product, please read the Safety Precau­tions carefully before using this product.

IMPORTANT SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property
damage if improperly handled. This product has been engineered and manufactured with the highest
priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent
potential danger, please observe the following instructions when installing, operating and cleaning the
product. To ensure your safety and prolong the service life of your LCD color TV product, please read
the following precautions carefully before using the product.

■ Read instructions—All operating instructions must be read and understood before the product is
operated.

■ Keep this manual in a safe place—These safety and operating instructions must be kept in a
safe place for future reference.

■ Observe warnings—All warnings on the product and in the instructions must be observed
closely.

■ Follow instructions—All operating instructions must be followed.

■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inad-

equate attachments can result in accidents.

■ Power source—This product must operate on a power source specified on the specification
label. If you are not sure of the type of power supply used in your home, consult your dealer or
local power company. For units designed to operate on batteries or another power source, refer
to the operating instructions.

■ Power cord protection—The power cords must be routed properly to prevent people from
stepping on them or objects from resting on them. Check the cords at the plugs and product.

■ If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a
SHARP service center or your dealer.

■ Overloading—Do not overload AC outlets or extension cords.
Overloading can cause fire or electric shock.

■ Entering of objects and liquids—Never insert an object into the product through vents or open­ings. High voltage flows in the product, and inserting an object can cause electric shock and/or
short internal parts. For the same reason, do not spill water or liquid on the product.

■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to
high voltage and other dangerous conditions. Request a qualified service person to perform
servicing.

■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and
request a qualified service person to perform repairs.
a.When the power cord or plug is damaged.
b.When a liquid was spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d.When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper

adjustment of controls not described in the instructions can cause damage, which often

requires extensive adjustment work by a qualified technician.
e.When the product has been dropped or damaged.
f. When the product displays an abnormal condition. Any noticeable abnormality in the product

indicates that the product needs servicing.

■ Replacement parts—In case the product needs replacement parts, make sure that the service
person uses replacement parts specified by the manufacturer, or those with the same character­istics and performance as the original parts. Use of unauthorized parts can result in fire, electric
shock and/or other danger.

■ Safety checks—Upon completion of service or repair work, request the service technician to
perform safety checks to ensure that the product is in proper operating condition.

■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the
product according to the method recommended by the manufacturer.

■ Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a
plug having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.

4

■ The LCD panel is a very high technology product with 921,600 thin film transistors, giving you fine
picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.
Please note that this does not affect the performance of your product.

IMPORTANT SAFETY PRECAUTIONS (Continued)

■ Cleaning—Unplug the power cord from the AC outlet before
cleaning the product. Use a damp cloth to clean the product.
Do not use liquid cleaners or aerosol cleaners.

■ Water and moisture—Do not use the product near water,

such as bathtub, washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.

■ Stand—Do not place the product on an unstable cart, stand,

tripod or table. Placing the product on an unstable base can
cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manu­facturer or sold with the product. When mounting the product
on a wall, be sure to follow the manufacturer’s instructions.
Use only the mounting hardware recommended by the
manufacturer.

■ When relocating the product placed on a cart, it must be

moved with utmost care. Sudden stops, excessive force and
uneven floor surface can cause the product to fall from the
cart.

■ Ventilation—The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block these vents
and openings since insufficient ventilation can cause over­heating and/or shorten the life of the product. Do not place
the product on a bed, sofa, rug or other similar surface,
since they can block ventilation openings. This product is not
designed for built-in installation; do not place the product in
an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer’s instruc­tions are followed.

■ The LCD panel used in this product is made of glass.

Therefore, it can break when the product is dropped or
applied with impact. Be careful not to be injured by broken
glass pieces in case the LCD panel breaks.

■ Heat sources—Keep the product away from heat sources

such as radiators, heaters, stoves and other heat-generating
products (including amplifiers).

5

IMPORTANT SAFETY PRECAUTIONS (Continued)

■ If an outside antenna is connected to the television equipment, be sure the antenna system is
grounded so as to provide some protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code provides information with respect to proper grounding
of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode.

■ An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.

ANTENNA
LEAD IN
WIRE

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

GROUND CLAMPS
POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(

NEC ART 250, PART H

)

ELECTRIC
SERVICE
EQUIPMENT

NEC—NATIONAL ELECTRICAL CODE

GROUND
CLAMP

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

■ For added protection for this television equipment during a
lightning storm, or when it is left unattended and unused for
long period of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the
equipment due to lightning and power-line surges.

6

CONTENTS

Page

IMPORTANT INFORMATION ....................................................................................................... 1, 2

DEAR SHARP CUSTOMER .............................................................................................................3

IMPORTANT SAFETY PRECAUTIONS ....................................................................................... 3-5

CONTENTS ....................................................................................................................................... 6

SUPPLIED ACCESSORIES ............................................................................................................. 7

PREPARATION ............................................................................................................................ 8-10

Using the Remote Control ......................................................................................................... 8

Batteries for the Remote Control .............................................................................................. 8

Antenna Connection .............................................................................................................9, 10

Power Connection .................................................................................................................... 10

DISPLAY AND CONTROL OVERVIEW .................................................................................. 11-13

Removing the Back Cover ....................................................................................................... 13

Listening with Headphones ..................................................................................................... 13

REMOTE CONTROL ...................................................................................................................... 14

EZ SETUP ....................................................................................................................................... 15

EZ SETUP during the First Power On .................................................................................... 15

BASIC OPERATION ................................................................................................................. 16-20

TV signals in your region ........................................................................................................ 16

Turning on POWER................................................................................................................... 17

Standby ...................................................................................................................................... 17

Switching TV/VIDEO [AV1/AV2/COMPONENT/TV] Modes ................................................... 18

Sound Volume ........................................................................................................................... 19

Changing Channels .................................................................................................................. 20

SELECTING MENU ITEMS ............................................................................................................21

Selecting Menu Items .............................................................................................................. 21

ADJUSTMENTS ........................................................................................................................ 22-42

Adjusting SLEEP TIMER Settings ........................................................................................... 22

Adjusting BRIGHTNESS Settings ........................................................................................... 23

Adjusting PICTURE FLIP Settings ..........................................................................................24

Adjusting PRESET Settings .................................................................................................... 25

Adjusting LANGUAGE Settings .............................................................................................. 26

Adjusting VIDEO ADJUST Settings ..................................................................................27, 28

Adjusting AUDIO ADJUST Settings .................................................................................. 29, 30

SET UP .................................................................................................................................31, 32

Adjusting BLUE SCREEN Settings ......................................................................................... 33

Adjusting CLOSED CAPTION Settings ............................................................................ 34, 35

Adjusting V-CHIP Settings .................................................................................................. 36-42

CONNECTING EXTERNAL DEVICES ..................................................................................... 43-45

Bundling Cables with Clamps ................................................................................................ 45

TROUBLESHOOTING ..............................................................................................................46, 47

SPECIFICATIONS........................................................................................................................... 48

DIMENSIONAL DRAWINGS .....................................................................................................49-51

CALLING FOR SERVICE ............................................................................................................... 52

LIMITED WARRANTY ..............................................................................................................52, 53

7

Make sure the following accessories are provided with the product.

SUPPLIED ACCESSORIES

AC CordAntenna Cable

“AAA” size (UM/SUM-4) Dry Battery (×2)

AC Adapter

UBATU0026GEZZ

QCNWG0003CEPA

UADP-0212CEZZ

TINS-A419WJZZ

Cable Clamp (×2)

ENGLISHFRANÇAISESPAÑOLPORTUGUÊS

QACCD3097CEPA

Operation Manual

Remote Control

RRMCGA118WJSA

LHLDWA002WJSA

UADP-A009WJPZ (LC-13/15C3U)

UADP-0243CEPZ (LC-20C3U)

8

PREPARATION

Batteries for the Remote Control

Before using the LCD TV set for the first time, install two (“AAA” size, UM/SUM-4) batteries (supplied).
When the batteries become depleted and the remote control fails to operate, replace the batteries with
new (“AAA” size, UM/SUM-4) batteries.

1 Open the battery

cover.

2 Insert two (“AAA” size, UM/

SUM-4) batteries.

3 Close the battery

cover.

■ Slide the cover while
pressing the (b) part.

■ Position the positive and
negative ends of the batteries
as indicated in the compart­ment.

Caution!

Cautions regarding batteries

Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instruc­tions below.

• Place batteries with their terminals corresponding to the (+) and (–) as indicated in the compartment.

• Different types of batteries have different characteristics. Do not mix batteries of different types.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new

battery and/or cause the old battery to leak chemicals.

• Remove batteries when they become weak.
Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a
cloth.

• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.

• If the remote control will not be used for an extended period of time, remove the batteries from the

remote control.

Using the Remote Control

■ Use the remote control by pointing it towards the remote

control sensor window on the main unit. Objects between
the remote control and sensor window may prevent proper
operation.

Cautions regarding use of the remote control

■ Do not expose the remote control to shock.

In addition, do not expose the remote control to liquid, and
do not place in an area with high humidity.

■ Do not install or place the remote control under direct

sunlight. The heat may cause deformation of the unit.

■ The remote control may not work properly if the remote

control sensor window of the main unit is under direct
sunlight or strong lighting. In such case, change the angle of
the lighting or LCD TV set, or operate the remote control
closer to the remote control sensor window.

+

–

+

–

SLEEPPOWER

■ Engage the claw on the
cover into the battery
housing and slide shut.

SLEEP indicator
POWER indicator
Remote control
sensor

9

V

I

D

E

O

S

-

V

I

D

E

O

A

U

D

I

O

HEAD
PHONE

L

R

A

V

-

I

N

1

V

ID

E

O

A

U

D

I

O

L

R

A

V

-

IN

2

/

O

U

T

Y

AN

T.

PO

W

ER

IN

PU

T

DC

13V

COMPONENT

L

R

A

UDIO

P

B

P

R

75-ohm

coaxial cable

300-ohm
twin-lead

VHF/UHF

antenna

VHF/UHF

antenna

300-75-ohm

adapter

(not supplied)

300-ohm
twin-lead

300-ohm
twin-lead

75-ohm
coaxial cable

OUT IN

VHF

antenna

UHF

antenna

Combiner

(not supplied)

or

ANT.

POWER

INPUT
DC13V

or

PREPARATION (Continued)

A. Combination VHF/UHF Antenna

OUTDOOR ANTENNA CONNECTION

• Use one of the following two diagrams if you connect an outdoor antenna.
A: Using a VHF/UHF combination outdoor antenna
B: Using separate VHF and/or UHF outdoor antennas

• Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the TV set.

B. Separate VHF and/or

UHF Antennas

F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (flat)

1. A 75-ohm system is generally a round cable with F-type
connector that can easily be attached to a terminal without
tools (not supplied).

2. A 300-ohm system is a flat “twin-lead” cable that can be
attached to a 75-ohm terminal through a 300-75-ohm
adapter (not supplied).

Antenna Connection

• The antenna requirements for good color television reception are more important than those for black & white
television reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connections that are provided with the various antenna
systems.

ANT. (Antenna
terminal)

Antenna cable (supplied)

ANTENNAS

10

Power Connection

A

• Use a commercially available AC plug adapter, if necessary, depending on the design of the wall outlet.

• Always turn the MAIN POWER switch of the LCD TV set to off when connecting the AC adapter.

• Unplug the AC adapter from the product and power outlet when not using for a long period of time.

PREPARATION (Continued)

Antenna Connection (Continued)

Cable TV converter/

descrambler

(not supplied)

Two-set
signal
splitter
(not
supplied)

Cable TV Line

RF switch (not supplied)

OUT

IN

A

• Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be
required.

POWER

INPUT
DC13V

VIDEO

S-VIDEO

AUDIO

HEAD
PHONE

L

R

A

V

-

IN

1

VIDEO

AUD

IO

L

R

A

V

-IN

2

/O

U

T

Y

A

N

T

.

P

O

W

E

R

IN

P

U

T

D

C

1

3

V

C

O

M

P

O

N

E

N

T

L

R

A

U

D

IO

P

B

P

R

• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-

ohm coaxial cable to the set, screw the 75-ohm cable to the ANT. terminal.

• Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay

channels are scrambled, a cable TV converter/descrambler is generally provided to the subscriber
by the cable TV company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set your TV to channel 3 or 4, typically one of these channels is used. If this
is unknown, consult your cable TV company.) For more specific instructions on installing cable TV,
consult your cable TV company. One possible method of utilizing the converter/descrambler
provided by your cable TV company is explained below.

Please note: An RF switch provided with two inputs (A and B) is required (not supplied).

“A” position on the RF switch (not supplied): You can view all unscrambled channels by using the TV’s

channel keys.

“B” position on the RF switch (not supplied): You can view the scrambled channels via the converter/

descrambler by using the converter’s channel keys.

CABLE TV (CATV) CONNECTION

Household power outlet

AC cord

AC adapter

POWER INPUT
terminal
(DC12V:LC-13C3U

: LC-15C3U

DC13V: LC-20C3U)

MAIN POWER

11

CHVOL

MENU

TV/VIDEO MAIN POWER

CHVOL

MENU

TV/VIDEO MAIN POWER

A

• TV/VIDEO, CH ( )/( ), VOL (–)/(+), and MENU on the main unit have the same functions as the same buttons
on the remote control. Basically, this operation manual provides a description based on operation with the remote
control.

• The LC-13C3U, LC-15C3U and LC-20C3U have different external dimensions and the positions where the names
of the buttons are displayed also differ but the same operating procedures are followed for all three models.

DISPLAY AND CONTROL OVERVIEW

MAIN POWER

TV/VIDEO

MENU

CH ( )/( )

VOL (–)/(+)

Speaker (Right)

SLEEP indicator

The SLEEP indicator lights up red when the
SLEEP TIMER is set.

Upper control panel

To change the vertical
angle of the LCD TV set,
tilt the screen up to 2.5
degrees forward or 10
degrees backward. The
TV set can also be
rotated 25 degrees
horizontally. Adjust the
angle so that the TV set
can be watched most
comfortably.

Speaker (Left)

POWER indicator

A green indicator lights when the power is
on and a red indicator lights when in the
standby mode (the indicator will not light
when the main power is off).

Controls

* The examples used throughout this manual are based

on the LC-20C3U model.

Subwoofer

LC-20C3U

LC-13C3U
LC-15C3U

Remote control sensor

12

V

ID

E

O

S-VIDEO

AUDIO

HEAD
PHONE

L

R

A

V

-IN

1

VIDEO

AUDIO

L

R

A

V

-IN

2

/O

U

T

Y

A

N

T

.

P

O

W

E

R

IN

P

U

T

D

C

1

3

V

C

O

M

P

O

N

E

N

T

L

R

A

U

D

IO

P

B

P

R

ANT.

Y

P

B

P

R

AUDIO

L

R

POWER

INPUT
DC13V

COMPONENT

VIDEO

S-VIDEO

AUDIO

HEAD
PHONE

L

R

AV-IN1

VIDEO

AUDIO

L

R

AV-IN2/OUT

DISPLAY AND CONTROL OVERVIEW (Continued)

ANT. (Antenna terminal)

AUDIO (L)

AUDIO (R)

HEADPHONE

POWER INPUT

(DC12V: LC-13C3U

: LC-15C3U

DC13V: LC-20C3U)

AUDIO (L)
AUDIO (R)

VIDEO

Y

P

R

PB

AV-IN2/OUT

COMPONENT

AUDIO (L)
AUDIO (R)

VIDEO

S-VIDEO

AV-IN1

Carrying handle

Hold the carrying handle and tilt the
screen while steadying the stand with
your other hand.

● Adjusting the screen view angle

Terminals

13

Listening with Headphones

DISPLAY AND CONTROL OVERVIEW (Continued)

■ Before connecting cables and cords to the rear terminals, remove the
back covers. Push in the tabs and pull out the back covers carefully.

■ To mount the cover, insert the 2 hooks on the bottom of the cover
into the cabinet and press on the upper part of the back cover until
the tab locks in place with a click.

Removing the Back Cover

■ Plug the headphone mini-plug into the HEADPHONE jack located on the rear of the TV set.

Headphones

A

• Headphones are not included in the supplied accessories.

• No sound is heard from the main unit speakers when a headphone mini-plug is connected into the

HEADPHONE jack.

▼ On-screen display

20

VOLUME

c Rear terminal

V

ID

E

O

S-V

ID

E

O

A

UD

IO

H

E

A

D

P

H

O

N

E

L

R

A

V

-IN

1

VID

EO

AU

DIO

L

R

A

V-IN

2/O

UT

V

ID

E

O

S

-V

I

D

E

O

A

U

D

IO

H

E

A

D

P

H

O

N

E

L

R

A

V

-

IN

1

V

I

D

E

O

A

U

D

I

O

L

R

A

V

-I

N

2

/O

U

T

Y

A

N

T

.

P

O

W

ER

IN

P

U

T

D

C

13

V

C

O

M

P

O

N

E

N

T

L

R

A

U

D

IO

P

B

P

R

Adjust the sound volume
using VOL (e)/(f) on the
remote control.

14

CHVOL

POWER

ENTER

SUB

MUTE

DISPLAY MENU

SLEEP PIC. FLIP

BRIGHT

CC

TV/VIDEO

RETURN

REMOTE CONTROL

1 POWER (p. 17)

Switch the Liquid Crystal Television power
on or off.

2 SUB (p. 29)

Switch the subwoofer on or off.

3 SLEEP (p. 22)

Set the sleep timer.

4 ENTER

Execute a command.

5 DISPLAY

Display the channel information.

6 BRIGHT (p. 23)

Adjust the brightness of the screen.

7 MUTE (p. 19)

Mute the sound.

8 VOL (+)/(–) (p. 19)

Set the volume.

9 CH ( )/( ) (p. 20)

Select channel.

10 MTS (p. 19)

Select audio settings.

11 PIC. FLIP (p. 24)

Set the orientation of the picture.

12 a/b/c/d (Cursor control) (p. 21)

Select a desired item on the screen.

13 MENU (p. 21)

Display the menu screen.

14 CC (p. 34)

Display Closed Caption subtitles.

15 TV/VIDEO (p. 18)

Select a Liquid Crystal Television input
source.

16 RETURN

Return to the previous channel.

17 Channel Select (p. 20)

Set the channel.

1

2
3

4
5

6

7

8

9

10

11

12

13

14

15

16

17

15

EZ SETUP

Control section of main unit

1 Press MAIN POWER, located on

the upper side of the main unit, to
turn on the TV. The SELECT
LANGUAGE mode will be dis­played.

2 Press a/b to select “ENGLISH”,

“ESPAÑOL (SPANISH)” or
“FRANCAIS (FRENCH)”.

3 Press ENTER to access EZ

SETUP mode.

4 Press d.

The tuner will automatically search
for the broadcasting and cable TV
channels. (The CH No. will
automatically increase when it
appears.)

If you want to stop the EZ SETUP
process once it has started, press
c and it will be canceled. If you
want to SET UP again, please refer
to pages 31 and 32 on SET UP.

To cancel EZ SETUP

Press c.

5 Once EZ SETUP is completed, the

lowest channel number memorized
will be displayed.

SELECT LANGUAGE
ENGLI SH
ESPAÑOL
FRANCAI S

SELECT : ENTER: EXIT:

ENTER

MENU

EZ SETUP during the First Power On

CHVOL

POWER

ENTER

SUB

MUTE

DISPLAY MENU

SLEEP PIC. FLIP

BRIGHT

CC

TV/VIDEO

RETURN

MAIN POWER

CHVOL

MENU

MAIN POWER

TV/VIDEO

ENTER/
a/b/c/d

■ When you turn on the TV for the first time, it will automatically
memorize the broadcasting channels.
Please perform the following instructions before you press MAIN
POWER.
(1) Insert the batteries into the remote control. (See page 8.)
(2) Connect the antenna cable to the TV set. (See page 9.)
(3) Connect the AC adapter to the POWER INPUT terminal of the

product and plug in the AC cord to the wall outlet. (See page 10.)

START EZ SETUP?

CONNECT ANTENNA OR CA BL E.

YES : NO : EXIT:

MENU

PLEASE WAIT

AUTO PROGRA

MM

ING

STOP:

2

A

• Do not let the EZ SETUP screen remain unattended for a long time.

• If EZ SETUP does not memorize all the channels in your region, please refer to pages 31 and 32 for more

information on manually memorizing the channels using CHANNEL SETTING.

• It may be difficult to preset when the broadcasting signals are weak, the channel cycle frequency is incorrect or
the frequency jamming is occurring around the area. Please refer to pages 31 and 32 for more information on
manually memorizing channels using CHANNEL SETTING.

MENU

16

Country

TV broadcasting

Factory setting of color system User setting

system

TV Video TV

U.S.A.

Color: NTSC NTSC (N358) World Multi

TV ch: US ch US ch Auto System

Not required or N/A

Canada, Mexico, Color: NTSC NTSC (N358) World Multi
Latin America TV ch: US ch US ch Auto System

Not required or N/A

Brazil

Color: PAL-M NTSC (N358) World Multi Set color system to
TV ch: US ch US ch Auto System PAL-M (see page 28)

Argentina, Color: PAL-N NTSC (N358) World Multi Set color system to
Uruguay TV ch: US ch US ch Auto System PAL-N (see page 28)

The World Multi Auto System
is compatible with all color
systems indicated below.

1 N358
2 N443
3 PAL
4 PAL-M
5 PAL-N
6 SECAM
7 PAL-60

BASIC OPERATION

Country

TV broadcasting

Factory setting of color system User setting

system

TV Video TV/Video

U.S.A.

Color: NTSC NTSC (N358) NTSC (N358)

TV ch: US ch US ch US ch

Not required or N/A

Canada, Mexico, Color: NTSC NTSC (N358) NTSC (N358)
Latin America TV ch: US ch US ch US ch

Not required or N/A

Brazil

Color: PAL-M NTSC (N358) NTSC (N358) Set color system to
TV ch: US ch US ch US ch PAL-M (see page 28)

Argentina, Color: PAL-N NTSC (N358) NTSC (N358) Set color system to
Uruguay TV ch: US ch US ch US ch PAL-N (see page 28)

A

• The 3 Dimensional Y/C separation circuit* only works when the color system is set to N358 in TV mode and Video
mode.
*The 3 Dimensional Y/C separation circuit is used to remove flickering and color bleeding.

This product is factory set to comply with the TV broadcasting system in the United States. For Brazil,
Argentina and Uruguay, set the color system according to the country before using this product by
following the table below.

■ LC-13C3U, LC-15C3U

The VIDEO INPUT mode is compatible with color systems worldwide and is automatically set.

■ LC-20C3U

TV signals in your region