Mounting the Lens
Remove the wide conversion lens
1
from its original box. Put the screw
thread of the wide conversion lens
and the projector lens together.
Projector lens
Fix the focus ring of the projector
2
manually. Then turn the wide
conversion lens clockwise slowly.
(NOTE: Mounting the lens when
the screw thread of both lenses
is incorrectly set may cause
damage. Make sure that the
screw thread of both lenses is set
correctly and then turn the wide
conversion lens slowly.)
When the wide conversion lens has been mounted, set
3
the part for preventing the lens from falling. (See the
“Mounting the part for preventing the lens from falling”
section in this manual.)
Wide conversion lens
Mounting the part for preventing the
lens from falling
Set the part for preventing the
1
lens from falling as shown on the
illustration. (Make sure that the
part is attached to the outer ditch
of the focus ring on the projector.)
Attach the two screws (included)
2
using the included screwdriver.
The part for preventing
the lens from falling
(included)
GB
2
AN_W9Z(E)#p02-05.pm6 01.12.27, 1:12 PM2
Adjust the picture size and focus
Refer to the “Zooming and Focusing” section in the Projector
Operation Manual for details about adjusting the picture size
and focus.
Before Calling for Service
1) Is the lens in focus? (See the “Zooming and Focusing”
section in the Projector Operation Manual.)
2) Is the projection distance within the range of focus?
(Check the projection distance charts).
Handling Precautions
• Do not disassemble this lens.
Please refer any maintenance and inspections, requiring
an open cabinet to your authorized dealer.
• Care
1) Mounting of the wide conversion lens should be
conducted in a dust free environment to avoid
dust particles entering the optical path between
the lens and projector.
2) When cleaning the lens, use compressed air or lens
cleaning material.
3) Avoid cleaning the lens with abrasive materials as
this may scratch the lens surface.
CAUTION
• Do not pack and transport the projector with the wide
conversion lens still attached.
• Do not expose the projector to shock while the wide
conversion lens is still attached.
AN_W9Z(E)#p02-05.pm6 01.12.27, 1:12 PM3
GB
3
Specifications
Product type
Model
Type of lens
Picture size (diagonal)
Focal length
F no.
Screen width to throw
distance ratio
Dimensions
Weight
Wide Conversion Lens for Projector
AN-W9Z
Wide conversion lens
50" to 150"
26.1 ~ 35.3mm
3.0
1.45 ~ 1.96:1
Ø 91.5 × 56.0
Approx. 410g
Throw distance chart
The replacement lens is a wide conversion lens. Once the
lens is installed, set the picture size and the projection
distance, referring to the table below.
Normal mode
When using a
normal screen (4:3)
In case of setting the
16:9 picture to the full
horizontal width of the
4:3 screen.
4
: Screen area
: Picture area
Screen size (4:3)
Diag.
Width
150"
100"
84"
72"
60"
The fomula for screen size and projection distance
3
y1 = (0.04038x – 0.06318)
y2 = (0.03x – 0.06317)
x : Screen size (diag.) (inches)
y : Projection distance (feet)
Height
120"
80"
67"
58"
48"
Projection Distance (y)
Maximum (y1)
90"
19'9" (6.0 m)
60"
13'1" (4.0 m)
50"
10'12" (3.3 m)
43"
9'5" (2.9 m)
36"
7'9" (2.4 m)
×
3.28
×
3.28
Minimum (y2)
14'7" (4.4 m)
9'8" (2.9 m)
8'1" (2.5 m)
6'11" (2.1 m)
5'8" (1.7 m)
• There is an error of ±3% in the formula above.
GB
4
AN_W9Z(E)#p02-05.pm6 01.12.27, 1:12 PM4
Wide mode
When using a
wide screen (16:9)
In case of displaying
the 16:9 picture on
the whole of the 16:9
screen.
16
: Picture area
Screen size (16:9)
Diag.
150"
133"
106"
100"
92"
84"
72"
9
60"
50"
Width
131"
116"
92"
87"
80"
73"
63"
52"
44"
Height
Projection Distance (y)
Maximum (y1)
74"
21'6" (6.6 m)
65"
19'1" (5.8 m)
52"
15'1" (4.6 m)
49"
14'3" (4.4 m)
45"
13'1" (4.0 m)
41"
11'12" (3.6 m)
35"
10'3" (3.1 m)
29"
8'6" (2.6 m)
25"
7' (2.1 m)
Minimum (y2)
15'1" (4.8 m)
14'1" (4.3 m)
11'1" (3.4 m)
10'6" (3.2 m)
9'7" (2.9 m)
8'9" (2.7 m)
7'6" (2.3 m)
6'2" (1.9 m)
5'2" (1.6 m)
The fomula for screen size and projection distance
y1 = (0.04423x – 0.06883)
y2 = (0.03268x – 0.06882)
x : Screen size (diag.) (inches)
y : Projection distance (feet)
• There is an error of ±3% in the formula above.
×
3.28
×
3.28
The specifications of the lens shift function are the same as
the standard lens. Refer to the “Setting Up the Screen”
section in the Projector Operation Manual.
Set-up Dimensions
Unit: mm
79.2
Ø
AN_W9Z(E)#p02-05.pm6 01.12.27, 1:12 PM5
452.3
406
178
GB
5
Loading...