In the interests of user safety (Required by safety regulations in some countries) the set should be restored to its original
condition and only parts indentical to those specified should be used.
World Multi 18 System
100-CH Program Memory
AV Mode (Movie/Music/News)
CATV Hyper Band Ready
Blue/White Stretch Circuit
Picture Noise Reduction
White Temp. Select
Gamma Correction
Multi Language OSD (English/France/Russian/Arabic)
Hotel Mode
Off Timer
Rear AV-IN 1, AV Output (Monitor Out), M.P.IN
The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and
power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Maintenance and repairing of this receiver should be done by
qualified service personnel only.
SERVICE OF HIGH VOLTAGE SYSTEM AND
PICTURE TUBE
When servicing the high voltage system, remove static charge from it by
connecting a 10K ohm resistor in series with an insulated wire (such as a test
probe) between picture tube dag and 2nd anode lead. (AC line cord should
be disconnected from AC outlet.)
1. Picture tube in this receiver employs integral implosion protection.
2. Replace with the same type number of picture tube for continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof goggles and after discharging
the high voltage completely.
29Q-FG1A/1F/1N/1S/1U
X-RAY
This receiver is designed so that any X-Ray radiation is kept to an absolute
minimum. Since certain malfunctions or servicing may produce potentially
hazardous radiation with prolonged exposure at close range, the following
precautions should be observed:
1. When repairing the circuit, please make sure do not increase the high voltage of the set
to more then 34.0kV (at beam 0 A).
2. To keep the set in a normal operation, please make sure it's function at 30.0kV 1.5kV
(at beam 1700 A). The set has been factory - adjusted to the above-mentioned high voltage.
*If there is a possibility that the high voltage fluctuates as a result of the repaires,
never forget to check for such high voltage after the work.
3. Do not substitute a picture tube with unauthorized types and/or brands which may cause
excessive X-ray radiation.
BEFORE RETURNING THE RECEIVER
Before returning the receiver to the user, perform the following safety checks.
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metal control knobs, insulating fishpapers,
cabinet backs, adjustment and compartment covers or shields, isolation resistor- capacity networks, mechanical insulators etc.
2 – 1
Page 4
29Q-FG1A/1F/1N/1S/1U
ADJUSTMENT PRECAUTIONS
This model's setting are adjusted in two different ways: through the I2C bus control and in the
conventional analog manner. The adjustments via the I2C bus control include preset-only items and
variable data.
1. Setting the service mode by the microprocessor.
(1). Press and hold the local key "VOL DOWN" & "CH UP" when power on the main switch,
Precaution: If haven't done this initialization, malfunction might be happen.
(1) The following default data has been factory-setting for the EEPROM.
GB7 PACKAGE 2 MODEL SET KEY
Model set will follow the data in table below (1.1).
MODEL-NAMEOSD LANGUAGESOUND SYSTEM
29Q-FG1A, 29Q-FG1NENGLISHB/G
29Q-FG1F, 29Q-FG1S
ARABIC
B/G
29Q-FG1URUSSIAND/K
Table 1.1
Default settings:
ItemsDefault Settings
Last powerON
Last TV/AV modeTV mode
Last position-TVProgram 1
Flashback Program-TV Program 1
Favorite Program AProgram 10
Favorite Program BProgram 20
Favorite Program CProgram 30
Favorite Program DProgram 40
1/2 digit entry2 digit
Volume0
AFTAll programs ON
AV MODEMOVIEMUSICNEWS
Contrast606050
Colour+60-6
Brightness000
Tint000
Sharpness+60-6
Picture NROFFOFFOFF
White temp000
(2) Select "RF-AGC" item in the Adjustment(2) Connect the oscilloscope to TP53 .
Item. Push the RF-AGC button, blue display
(Tuner's AGC Ter minal) as shown in figure 3-1.
with OK sign indicates the adjustment is
working properly.OSCILLOSCOPE
BIAS BOX
TV SET
Bias Box : about 4.5V
Fig. 3-1
(3) Select "RF-AGC" item in the Adjustment
Mode. Adjust the "RF-AGC" bus data to
obtain the Tuner output pin drop
0.1V1.0V
below maximum voltage.
(4) Change the antenna input signal to 63 ~ 67dBµV, and make s ure there is no nois e.
(5)Turn up the input signal to 90 ~ 95 dBµB to be sure that there is no c ross modulation beat.
FOCUS ADJUSTMENT
NO ADJUSTMENT POINTADJUSTMENT CONDIT ION / PROCEDUREWAVEFORM OR REMARKS
1FOCUS1. Receive E-5CH (Monoscop patter n).
ADJUSTMENT2. With the remote controller, m ake the image normal.
3. Adjust the focus VR to make the character"575" on lef t bottom of m onoscope
as fine as possible.
CUT OFF, BKGD, SUB-CONT ADJUSTMENT
NO ADJUSTMENT POINTADJUSTMENT CONDIT ION / PROCEDUREWAVEFORM OR REMARKS
1CRTCUTOFF
ADJUSTMENT1. Make sure following items are in INT IAL DATA before adj ust CRT cutoff.
(I2C BUS CONTROL)
a) 18 CUT-RS = 32
b) 19 CUT-GS = 32
c) 58 CUT OFF = 10
2. Switch TV to video mode, blue back off, with no signal and press R/C to set picture
into normal condition.
3. Go to service mode at adjustment mode item A057 VSD and press Volum e Up at R/C.
4. Adjust screen voltage until retrace line j ust become visible.
PAL CHROM A ADJUSTMENT
NO ADJUSTMENT POINTADJUSTMENT CONDIT ION / PROCEDUREWAVEFORM OR REMARKS
1SUB COLOUR1. Receive the "PAL Color Bar" signal.
(I2C BUS CONTROL) 2. Make the image normal with the rem ote controller.Cy GB
3. Connect the oscilloscope to TP47R (IC851 #9
( Use Probe 10:1)
Range : 2V / Div Sweep tim e: 20m sec / Div
4. Set the sub color adjustment mode with the remote contr oller, and vary the sub
color data to mak e 100% W of the color bar and RED at the same level for
adjustment shown in F ig. 1-1.75 % W Y 100%
WMg
R
NOTE : Due to diff erent signal between SEM & SREC, please add 2 step
Fig. 1-1
after adjust sub color. This instruction effective for SREC production
only.
NTSC CHROMA ADJUSTMENT
NO ADJUSTMENT POINTADJUSTMENT CONDIT ION / PROCEDUREWAVEFORM OR REMARKS
1SUB-T INT(1) Receive the "NTSC 3.58 Colour Bar" signal through AV IN
Same Level
(I2C BUS CONTROL) (2) Connect the oscilloscope to TP47B (P860 Pin4) BLUE-OUT
Range: 100mV/Div (AC)(Use Probe 10:1)
Sweep time
:10sec/Div
(3) Select the "SUB-TINT " item in the ADJUSTMENT MODE.. Adjust the "SUB-TINT"
data to obtain the waveform shown as Figure 1.1 (W and Mg same level)
(4) Minus 2 steps of adjustment value from item (3).
NOTE : Gnd for oscilloscope must be connected to small signal gnd in CRT
board. If others lo cation gnd is used, please offset the sub tint
value accordingly
Auto Adju stme nt
Manual Adjustment
-
TP53
0.1V
䌾
1.0V
W
YCyG
Mg
R
B
[2] ADJUSTMENT
3 – 11
Page 15
CUT OFF, BKGD, SUB-CONT ADJUSTMENT CONTINUED
NOADJUSTMENT POINTADJUSTMENT CONDITION / PROCEDUREWAVEFORM OR REMARKS
2WHITE BALANCE(1) Receive the internal RF monoscope pattern.
BACKGROUND(2) Make the picture normal with the remote controller.
I2C BUS(3) Connect the beam ammeter between terminal of R623.7500K X : 0.300 Y : 0.310
ADJUSTMENT(4) Coarsely confirm the beam current to approx. 1.7mA.18000K X : 0.255 Y : 0.255
(AV-IN SIGNAL)(5) Receive the window pattern with AV input.17000K X : 0.261 Y : 0.261
(6) With the data of DRI-GS and DRI-BS, adjust the color temperature of the 50% white.
12300K X : 0.272 Y : 0.275
(7) Adjust the right dark area of the window to
12300K
with CUT-RS
( With Monolta color thermometer CA-100)
and CUT-GS.
(8) Go back to 50% white area to check colour temperature, if out of range, please
go back to step (6).
* 12300ºK
DRI-GW = "DRI-GS" - 7
DRI-BW = "DRI-BS" - 7
Note 1: Apply this adjustment after aging 30 min or more with the beam currentDRI-GC = "DRI-GS" - 7
1700 ± 50µA. (On the white or green monocolor screen)DRI-RC = 25
2: The colour temperature is based on the shipment destination as shown in Table 2.1 at* 17000ºK & 18000ºK
page 20.DRI-GW = "DRI-GS" - 7
DRI-BW = "DRI-BS" - 7
3: Adjust DRI-GC/GW, DRI-BC/BW , CUT-RW/C and CUT-GW/C as following DATA,DRI-GC = "DRI-GS" - 5
after finishing DRI-BS and DRI-GS DATA adjustment.DRI-RC = 27
4SUB-BRIGHTNESS(1) Receive the window pattern with AV input.
ADJUSMENT(2) Make the image normal with the remote controller.Note 1: Use "Y" of Minolta color analyzer
(I2C BUS CONTROL) (3) Select the sub- bright adjustment mode with the remote controller, and adjust theCA-100 in adjustment
(AV-IN SIGNAL)
right dark white area of the window pattern to
3.0cd ± 0.5cd
Note 2: Use the window pattern of the signal
generator SX-1006 for adjustment.
5SUB-BRIGHTNESS(1) Select DVD mode.
ADJUSMENT(2) Receive the signal of the DVD signal generator . ( Component signal)
(I2C BUS CONTROL)( Window Pattern)
(DVD SIGNAL)(3) Make the image normal with the remote controller.
(4) Select the SUB-BRIGHT adjustment mode (DVD) , and adjust the right dark white
area of the window pattern to
3.0cd ± 0.5cd
6SUB-CONTRAST(1) Receive the window pattern with AV input.
I2C BUS(2) Make the image normal with the remote controller.
ADJUSTMENT(3) Select the SUB-CONTRAST adjustment mode with the remote controller, and
(AV-IN SIGNAL)
adjust 50% white to
130 ± 10cd.
Note : Make sure the TV set already in the RF receiving atate before changing to AV mode
to contimue with this adjustment (no power OFF from the previous adjustment).
7SUB-CONTRAST(1) Select the DVD mode.
I2C BUS(2) Receive the signal of the DVD signal generator. ( Component signal)
ADJUSTMENT(Window Pattern)
(DVD SIGNAL)(3) Select the SUB-CONTRAST adjustment mode (DVD) with the remote controller,
and adjust 50% white to
130 ± 10cd.
Note : Make sure the TV set already in the RF receiving atate before changing to AV mode
to contimue with this adjustment (no power OFF from the previous adjustment).
50% white
dark white
29Q-FG1A/1F/1N/1S/1U
3 – 12
Page 16
29Q-FG1A/1F/1N/1S/1U
HORIZONTAL , VERTICAL, DEFLECTION LOOP AND ADJUSTMENT
NOADJUSTMENT POINTADJUSTMENT CONDITION / PROCEDUREWAVEFORM OR REMARKS
1MAIN SCREEN
ADJUSTMENT
A
V-SLOPEAdjust V-Slope by Volume Up / Down Remote Control.(monoscope)
Refer to Fig. 1.1.
V-SHI-50Align the center of the screen to the geometric center of CRT.(monoscope)
V-AMP-50Adjust the overscan to 8%(monoscope)
V-LINAdjust the linearity to the best.(monoscope)
S CORAlready preset.(Adjust this unless the linearity is achieved.)(monoscope)
H-SHI-50Align the center of the screen to the geometric center of CRT.(monoscope)
EW-W-50Adjust the overscan to 10%(monoscope)
E/W-PAR-50Adjust the 2nd vertical line from the right end of the crosshatch pattern
(crosshatch)
UPCOR-PARAdjust the 2nd upper vertical line from the right end of the crosshatch pattern
(crosshatch)
LOCOR-PARAdjust the 2nd lower vertical line from the right end of the crosshatch pattern
(crosshatch)
H-BOWAdjust the 2nd vertical line from the end of the crosshatch pattern
Refer to Fig 1.7.
(crosshatch)
H-PARAdjust the 2nd vertical line from the end of the crosshatch pattern(crosshatch)
Refer to Fig 1.6.
EW-TRAPAdjust the 2nd vertical line from the right end of the crosshatch pattern
so that the D1 (center area of the second vertical line - edge of screen)
and D2 (top area of the second vertical line - edge of screen) are same.
Refer to Fig 1-5.(crosshatch)
V-SHI-60Align the center of the screen to the geometric center of CRT.(monoscope)
V-AMP-60Adjust the overscan to 10%.(monoscope)
H-SHI-60Align the center of the screen to the geometric center of CRT.(monoscope)
EW-W-60Adjust the overscan to 10% .(monoscope)
E/W-PAR-60Adjust the 2nd vertical line from the right end of the crosshatch pattern
(crosshatch)
B
C
A = Out of spec
B=OK
C = Out of spec
Fig 1-1
Fig 1-2
Fig 1-3
Fig 1-4
Fig 1-5
H-PAR
Fig 1.6
D2
D1
H-BOW
Fig 1.7
3 – 13
Page 17
FUNCTION OPERATION CHECKING (1) (VIDEO & AUDIO)
NOADJUSTMENT POINTADJUSTMENT CONDITION / PROCEDUREWAVEFORM OR REMARKS
(3) Press Volume Up/Down key to check W HITE TEMP Option, STANDARD:
NORMAL SETTING, W ARM for more REDDISH direction changing, COOL for
more BLUISH direction changing.
8COLOUR SYSTEM(1) Receive the "PAL COLOUR BAR" signal, press the COLOUR SYSTEM
key to select modes except PAL, check the COLOUR is not working properly.
Then, select the "PAL" mode. Check again its colour so that it is working properly.
(2) Receive "SECAM COLOUR BAR" signal, press COLOUR SYSTEM
key to select modes except SECAM, check the COLOUR is not working properly.
Then, select the "SECAM" mode. Check again its colour so that it is working
properly.
(3) Receive "NTSC 4.43" signal, press COLOUR SYSTEM key to select
modes except NTSC 4.43, check the COLOUR is not working properly.
Then, select the "NTSC 4.43" mode. Check again its colour so that it is working
properly.
SYSTEM key to select modes except N4.43/3.58, check the COLOUR is not
working properly. Then, select the "NTSC 4.43/3.58" mode. Check again its
colour so that it is working properly.
29Q-FG1A/1F/1N/1S/1U
3 – 14
Page 18
29Q-FG1A/1F/1N/1S/1U
CHECKING FUNCTION OPERATION (2) (VIDEO & AUDIO) CONTINUED
NOADJUSTMENT POINTADJUSTMENT CONDITION / PROCEDUREWAVEFORM OR REMARKS
9SUB VOL(1) Receive PAL color bar signal. Signal content : 400 Hz 100% Mod. (Note *)
Note *
(BUS ADJUSTMENT)Make sure the sound setting is :-
(2) Normalize TV using rem ote control. Set Volume Max.
*MOVIEMODE
(3) Select
SUB-VOL (61)
in Adjustment mode. Then demute sound using remote control
* SURROUND : ONI
*TREBLE:+6
(4) Connect multimeter probe to Right Speaker terminal.
*BASS:+4
* BALANCE : 0
(5) Adjust the SUB-VOL data to make indication in the range
8.3~9.0 Vrms
*LOUDNESS:ON
Note : If the reading initially already in the stated range, no adjustment is needed.
10SOUND SYSTEM(1) Receive "PAL-D/K" signal, press the "SOUND SYSTEM"
to select B/G, I. Check the sound output is not working properly.
Select D/K and check the sound output to make sure it is working properly.
(2) Receive "PAL-I" signal, press the "SOUND SYSTEM"
to select B/G, D/K. Check the sound output is not working properly.
Select I and check the sound output to make sure it is working properly.
(3) Receive "PAL-B/G" signal, press the "SOUND SYSTEM"
to select I, D/K. Check the sound output is not working properly.
Select B/G and check the sound output to make sure it is working properly.
11HEADPHONE(1) Receive PAL COLOR BAR with sound 400 Hz ,100% modulation (± 50kHz Dev)
OUTPUT CHECKING
(FOR MODEL W ITH(2) Maximum volume , and check the headphone output with 400kHz sound
HEADPHONE FEATURE)and no sound out from speaker .
Ref : OUTPUT level of HEADPHONE is as following
Apx. 500mVp-p
12NOISE MUTE(1) Receive "PAL COLOUR BAR" signal.
CHECKING
(2) Turn up the volume control to maximum, make sure the sound is
heard from the speakers. Then put the unit in no signal state.
(3) Check the sound mute is effective.
(4) Finally turn sound level of CTV to m inimum.
13M.P.IN1) Turn up the volume control to maximum, make sure the sound is heard from speakers
4) of IC1100. Also
check the waveform
no.5 of IC501 and its
related parts. Check
8V supply at pin 36
of IC1100, 5V supply
at pin 55, 35, 18 &
11 of IC1100.
GREEN
RED
RED
No
Check 3.3V supply at
pin2,4,5&75of
IC1100. Check
oscillation of crystal
X1001.
Check CRT connector
(KY), (H) bias.
(Heater voltage 120 V,
210 V line)
Normal
Check R,G,B
input and output
of IC 851.
Abnormal
Check the heater
voltage 120V and
210V line from the
main PWB side.
4 – 1
Page 20
29Q-FG1A/1F/1N/1S/1U
NO LED LIGHT
Check F701
Normal
Does STBY+5V appear at pin 4
IC752 main unit ?
No
Check the power
circuit consisting of
IC701, IC702, T701
and its related parts.
Check 3V output
from pin 1 of IC
704 and its related
parts.
Blown out
Replace the fuse
No
Is the fuse again blown out ?
Yes
Check the power circuit
consisting of IC701,
IC702, D704 and its
related parts.
Yes
4 – 2
Page 21
NO NORMAL SOUND
29Q-FG1A/1F/1N/1S/1U
YES
Check IC301 &
its surrounding
circuit.
No sound
comes out at
AV-out J905.
Check sound output
signal from pin 23 &
24 of IC1100 and its
related circuit.
NO
Check input signal
at pin 13 & 14 of
IC3801.
NO
No sound from the
speaker.
Set volume to maximum. Is there
any sound output signal at pin 11 &
9 of IC301 ?
NO
Check if there is
sound input signal
Check connection
to the speaker.
at pin 2 & 4 of
IC301.
Check output
signal at pin 25,
26 of IC1100 and
its related circuit.
YES
Check IC3801 &
its surrounding
circuit.
YES
4 – 3
Page 22
29Q-FG1A/1F/1N/1S/1U
NO PICTURE
Snow noise
increase
Does 5V appear
at pin 7 of TU 251 ?
YES
Does 31V appear
at pin 9 of TU 251 ?
YES
Check TU 251
YES
NO
NO
Does the snow noise
appear on the screen at
maximum contrast and
brightness ?
Check the PC+5V line.
Check +120V line and
its related circuit.
NO
A
4 – 4
Page 23
A
No snow noise
Check pin 45 &
46 of IC 1100.
29Q-FG1A/1F/1N/1S/1U
Abnormal (No
signal or noise)
Noise or signal
appear.
Does AV input at
AV1 & AV2 normal ?
NO
Check pin 29 & 31 of
IC 1100. Does signal
or noise appear ?
NO
Check circuit
between AV-in
terminal and pin 29 &
31 of IC 1100.
YES
YES
Check TU 251
(Tuner), SF 202 and
its related circuit.
Check IC 1100 and
its related circuits.
Check IC 1100 RGB
out at pin 6, 7 & 8.
Is the output normal ?
NO
Check IC 1100 and
its related circuit.
YES
Does signal output
atpin7,8&9of
IC 851 normal ?
NO
Check IC 851 at
input pin 1, 2 & 3
and its related
circuit.
YES
Check the related
circuit of screen
heater (FBT) and
the CRT.
4 – 5
Page 24
29Q-FG1A/1F/1N/1S/1U
NO SPECIFIC COLOUR
Is only RF signal's colour
abnormal ?
YES
Check tuner TU 251,
SF 202 and its related
circuit.
NO
NO COLOUR
Adjust the colour
control at the user
MENU. Does colour
appear ?
NO
Go to CHANNEL
SETTING at the user
MENU and change
to the appropriate
colour system. Does
the colour appear ?
NO
Using a PAL colour
bar signal, check the
RGBin&outline
between IC 1100 and
IC 851. Does the
waveforms normal ?
YES
YES
COLOUR PRODUCED
Set the
appropriate
colour level.
Set the
appropriate
colour system.
B
NO
Check IC 851, IC
1100 and its related
circuit.
4 – 6
Page 25
B
Is some colours produced
in the B/W broadcast
reception ?
29Q-FG1A/1F/1N/1S/1U
NO
Check IC 1100
& IC 851 and its
related circuit
including the
RGB input &
output line.
Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
RJ2VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ52VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ53VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ55VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ56VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ57VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ65VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ66VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ125VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ251VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ701VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ702VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ703VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ704VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ705VRS-CY1JF000JYAAR0 1/16W Metal Oxide
RJ751VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R205VRS-CY1JF471JYAAR470 1/16W Metal Oxide
R206VRS-CY1JF392JYAAR3.9k 1/16W Metal Oxide
R207VRS-CY1JF272JYAAR2.7k 1/16W Metal Oxide
R208VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R210VRS-RG3AB221J+AAR220 1W Metal Film
R211VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R221VRD-RA2BE181JYAAR180 1/8W Carbon
R227VRS-CY1JF680JYAAR68 1/16W Metal Oxide
R228VRS-CY1JF102JYAAR1k 1/16W Metal Oxide
R230VRS-CY1JF391JYAAR390 1/16W Metal Oxide
R231VRS-CY1JF105JYAAR1 1/16W Metal Oxide
R249VRS-CY1JF123JYAAR12k 1/16W Metal Oxide
R250VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R253VRS-CY1JF123JYAAR56k 1/16W Metal Oxide
R254VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R255VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R307VRS-CY1JF822JYAAR8.2k 1/16W Metal Oxide
R308VRS-CY1JF222JYAAR2.2k 1/16W Metal Oxide
R309VRS-CY1JF123JYAAR12k 1/16W Metal Oxide
R310VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R311VRS-CY1JF681JYAAR680 1/16W Metal Oxide
R314VRS-CY1JF222JYAAR2.2k 1/16W Metal Oxide
R315VRS-CY1JF822JYAAR8.2k 1/16W Metal Oxide
R319VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R321VRS-CY1JF104JYAAR100k 1/16W Metal Oxide
R323VRD-RA2BE102JYAAR1k 1/8W Carbon
R324VRD-RA2BE183JYAAR18k 1/8W Carbon
R325VRD-RA2BE153JYAAR15k 1/8W Carbon
R335VRD-RM2HD1R0JYAAR1 1/2W Carbon
R336VRD-RM2HD1R0JYAAR1 1/2W Carbon
R347VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R348VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R351VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R352VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R353VRS-CY1JF471JYAAR470 1/16W Metal Oxide
R354VRS-CY1JF471JYAAR470 1/16W Metal Oxide
R355VRD-RA2BE333JYAAR33k 1/8W Carbon
R356VRD-RA2BE000JYAAR0 1/16W Metal Oxide
R357VRD-RA2BE101JYAAR100 1/8W Carbon
R375VRS-CY1JF562JYAAR5.6k 1/16W Metal Oxide
R376VRS-CY1JF562JYAAR5.6k 1/16W Metal Oxide
R391VRN-RL3DBR10J+AAR0.10 2W Metal Film
R395VRS-CY1JF000JYAAR0 1/16W Metal Oxide
29Q-FG1A/1F/1N/1S/1U
DESCRIPTION
5
Page 45
29Q-FG1A/1F/1N/1S/1U
NO.PARTS CODE
[3] MAIN UNIT
R402VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R403VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R404VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R421VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R422VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R423VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R501VRS-RG3AB221J+AAR220 1W Metal Film
R502VRN-RL3DB5R6J+ABR5.6 2W Metal Oxide
R503VRS-RG3DB271J+ABR270 2W Metal Oxide
R504VRS-RG3DB561J+ABR560 2W Metal Oxide
R505VRN-RA2BK182FYABR1.8k 1/8W Carbon
R506VRN-RL3DB1R0J+ABR1 2W Metal Oxide
R507VRN-RA2BK182FYABR1.8k 1/8W Carbon
R508VRD-RA2BE103JYAAR10k 1/8W Carbon
R509VRD-RA2BE222JYAAR2.2k 1/8W Carbon
R510VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R518VRD-RA2BE101JYAAR100 1/8W Carbon
R519VRD-RA2BE101JYAAR100 1/8W Carbon
R520VRD-RA2BE101JYAAR100 1/8W Carbon
R521VRS-CY1JF123JYAAR12k 1/16W Metal Oxide
R601VRS-CY1JF393FYAAR39k 1/16W Metal Oxide
R602VRS-RG2HC270J+AAR27 1/2W Metal oxide
!
!
!
!
!
!
R604VRN-RL3AB4R7J+AAR4.7 1W Metal Film
R605VRD-RA2EE103JYAAR10k 1/4W Carbon
R606VRN-RL3ABR47J+AAR0.47 1W Metal Film
R607VRD-RA2EE103JYAAR10k 1/4W Carbon
R608VRS-CY1JF393JYAAR39k 1/16W Metal Oxide
R609VRN-RL3DB6R8J+ABR6.8 2W Metal Oxide
R611VRD-RM2HD332JYAAR3.3k 1/2W Carbon
R612VRD-RA2BE101JYAAR100 1/8W Carbon
R613VRD-RA2BE103JYAAR10k 1/8W Carbon
R614VRD-RM2HD124JYAAR120k 1/2W Carbon
R615VRD-RM2HD124JYAAR120k 1/2W Carbon
R616VRD-RM2HD123JYAAR12k 1/2W Carbon
R618VRN-RL3ABR47J+AAR0.47 1W Metal Film
R619VRS-RG3DB183J+ABR18K 2W Metal Oxide
R621VRD-RM2HD220JYAAR22 1/2W Carbon
R622VRD-RA2BE394JYAAR390k 1/8W Carbon
R623VRS-RG2HC102J+AAR1k 1/2W Metal oxide
R624VRD-RA2BE394JYAAR390k 1/8W Carbon
R625VRD-RA2BE394JYAAR390k 1/8W Carbon
R626VRS-RG3AB562J+AAR5.6k 1W Metal Film
R628VRW-KQ3NC1R2KABR1.2 7W Metal Oxide
R633VRS-CY1JF331JYAAR330 1/16W Metal Oxide
R634VRS-CY1JF331JYAAR330 1/16W Metal Oxide
R635VRS-CY1JF332JYAAR3.3k 1/16W Metal Oxide
R637VRD-RA2BE563JYAAR56k 1/8W Carbon
R638VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R639VRS-KA3NG152JADR1.5k 7W Metal Oxide
R640VRS-CY1JF182JYAAR1.8k 1/16W Metal Oxide
R643VRN-VV3LB3R3J+ABR3.3 2W Metal Oxide
R645VRN-RA2BK473FYAAR47k 1/8W Carbon
R652VRS-CY1JF102JYAAR1k 1/16W Metal Oxide
R654VRS-RG3DB103J+ABR10k 2W Metal Oxide
R657VRS-KQ3HC681KADR680 5W Metal Oxide
R664VRD-RA2BE123JYAAR12k 1/8W Carbon
R671VRD-RA2BE101JYAAR100 1/8W Carbon
R701VRD-RA2BE220JYAAR22 1/8W Carbon
R703VRD-RA2BE332JYAAR3.3k 1/8W Carbon
R704VRD-RA2BE221JYAAR220 1/8W Carbon
R707VRS-VV3DB104JABR100k 2W Metal Oxide
R708VRD-RA2BE683JYAAR68k 1/8W Carbon
R712RR-HZ0014GEZZYAER12 1
R713VRD-RA2BE222JYAAR2.2k 1/8W Carbon
R714VRD-RA2BE393JYAAR39k 1/8W Carbon
R715VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R717VRS-RG3DB104J+ABR100k 2W Metal Oxide
R718VRN-RA2BK124FYAAR120k 1/8W Carbon
R719VRN-RA2BK563FYAAR56k 1/8W Carbon
R720VRD-RA2BE334JYAAR330k 1/8W Carbon
R721VRN-RA2BK124FYAAR1.8k 1/8W Carbon
R722VRN-RA2BK562FYAAR5.2k 1/8W Carbon
R738VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R739VRD-RA2BE102JYAAR1k 1/8W Carbon
R741VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R761VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R764VRN-RA2BK102FYAAR1k 1/8W Carbon
R766VRD-RA2BE100JYAAR100 1/8W Carbon
R768VRD-RA2EE182JYAAR1.8k 1/4W Carbon
R769VRD-RA2BE821JYAAR820 1/8W Carbon
R905VRD-RA2BE101JYAAR100 1/8W Carbon
R906VRD-RA2BE101JYAAR100 1/8W Carbon
R907VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R909VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R910VRD-RA2BE101JYAAR100 1/8W Carbon
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
6
Page 46
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
[3] MAIN UNIT
R913VRD-RA2BE101JYAAR100 1/8W Carbon
R915VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R917VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R918VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R919VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R920VRD-RA2BE750JYAAR75 1/8W Carbon
R921VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R922VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R923VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R924VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R925VRD-RA2BE101JYAAR100 1/8W Carbon
R926VRD-RA2BE101JYAAR100 1/8W Carbon
R930VRS-CY1JF750JYAAR75 1/16W Metal Oxide
R931VRS-CY1JF750JYAAR75 1/16W Metal Oxide
R932VRS-CY1JF750JYAAR75 1/16W Metal Oxide
R933VRS-CY1JF750JYAAR75 1/16W Metal Oxide
R935VRS-CY1JF104JYAAR100k 1/16W Metal Oxide
R938VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R940VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R941VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R942VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R943VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R944VRS-CY1JF000JYAAR0 1/16W Metal Oxide
R946VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R947VRS-CY1JF561JYAAR560 1/16W Metal Oxide
R948VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R949VRS-CY1JF561JYAAR560 1/16W Metal Oxide
R950VRS-CY1JF102JYAAR1k 1/16W Metal Oxide
R953VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R954VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R956VRS-CY1JF102JYAAR1k 1/16W Metal Oxide
R959VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R961VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R962VRD-RA2BE102JYAAR1k 1/8W Carbon
R963VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R965VRD-RA2BE101JYAAR100 1/8W Carbon
R966VRD-RA2BE560JYAAR56 1/8W Carbon
R968VRD-RA2BE331JYAAR330 1/8W Carbon
R969VRS-CY1JF223JYAAR22k 1/16W Metal Oxide
R970VRD-RA2BE331JYAAR330 1/8W Carbon
R977VRS-CY1JF104JYAAR100k 1/16W Metal Oxide
R978VRS-CY1JF104JYAAR100k 1/16W Metal Oxide
R1002 VRS-CY1JF331JYAAR330 1/16W Metal Oxide
R1003 VRS-CY1JF681JYAAR680 1/16W Metal Oxide
R1005 VRS-CY1JF222JYAAR2.2k 1/16W Metal Oxide
R1006 VRS-CY1JF152JYAAR1.5k 1/16W Metal Oxide
R1011 VRD-RA2BE101JYAAR100 1/8W Carbon
R1012 VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R1014 VRD-RA2BE391JYAAR390 1/8W Carbon
R1020 VRS-CY1JF181JYAAR180 1/16W Metal Oxide
R1021VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R1022 VRD-RA2BE183JYAAR18k 1/8W Carbon
R1023VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R1024VRS-CY1JF473JYAAR47k 1/16W Metal Oxide
R1027VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R1028 VRD-RA2BE101JYAAR100 1/8W Carbon
R1029 VRD-RA2BE102JYAAR1k 1/8W Carbon
R1030 VRD-RA2BE101JYAAR100 1/8W Carbon
R1031 VRS-CY1JF122JYAAR1.2k 1/16W Metal Oxide
R1032 VRD-RA2BE101JYAAR100 1/8W Carbon
R1033 VRD-RA2BE181JYAAR180 1/8W Carbon
R1034 VRD-RA2BE472JYAAR4.7k 1/8W Carbon
R1035 VRD-RA2BE101JYAAR100 1/8W Carbon
R1036 VRD-RA2BE101JYAAR100 1/8W Carbon
R1037 VRD-RA2BE122JYAAR1.2k 1/8W Carbon
R1039 VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R1040 VRS-CY1JF101JYAAR100 1/16W Metal Oxide
R1041 VRS-CY1JF221JYAAR220 1/16W Metal Oxide
R1042 VRD-RA2BE101JYAAR100 1/8W Carbon
R1043 VRS-CY1JF152JYAAR1.5k 1/16W Metal Oxide
R1044 VRD-RA2BE101JYAAR100 1/8W Carbon
R1045 VRD-RA2BE333JYAAR33k 1/8W Carbon
R1046 VRD-RA2BE101JYAAR100 1/8W Carbon
R1047 VRD-RA2BE101JYAAR100 1/8W Carbon
R1048 VRD-RA2BE101JYAAR100 1/8W Carbon
R1050 VRD-RA2BE101JYAAR100 1/8W Carbon
R1051 VRS-CY1JF331JYAAR330 1/16W Metal Oxide
R1052 VRS-CY1JF332JYAAR3.3k 1/16W Metal Oxide
R1104 VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R1105 VRS-CY1JF472JYAAR4.7k 1/16W Metal Oxide
R1107 VRD-RA2BE101JYAAR100 1/8W Carbon
R3802VRS-CY1JF103JYAAR10k 1/16W Metal Oxide
R3803 VRS-SV2HC221JYAAR220 1/2W Metal oxide
RDA301PRDARA287WJFWAHRHeat Sink for IC301
RDA501PRDARA288WJFWAGRHeat Sink for IC501
RDA602PRDARA361WJFWRHeat Sink for Q602
RDA604PRDAR0224PEFWRHeat Sink for Q604
RDA701PRDARA286WJFWAGRHeat Sink for IC701
RDA755PRDARA181WJFWACRHeat Sink for D755
CCABAB742WEV1-RFront Cabinet Ass'y ( 29Q-FG1U )
1-1Not Available--Front Cabinet
1-2GCOVAB964WJSA-RLED / Remote Control Cover
1-3GDORFA197WJSA-RDoor
1-4HBDGB3141CESAAGRSharp Badge
1-5HINDPC058WJSA-RIndication Plate
1-6JBTN-A626WJSA-RPower Button
1-7MSPRCA040WJFW-RSpring For Power Button
1-8MSPRPA003WJFW-RSpring For Door
1-9PSPAGA026WJZZ-RRubber Spacer For Door
3SPAKCD166WJZZ--Packing Case
4SPAKXB333WJZZ--Buffer Material Top
5SPAKXB355WJZZ--Buffer Material Rear
6SPAKXB334WJZZ--Buffer Material Bottom
7SSAKA0001PEZZ--Poly Bag For Accessory
8SSAKH0018PEZZ--Wrapping Sack For Set
9TLABZB390WJZZ--Case Label ( 29Q-FG1A )