Sharp 68-409-01 User Manual

Sharp Installation Configuration and Connections

SYSTEM 8/10 Plus

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: SHARP

Included Communications Adapter(s):

Quantity Part Number Description

1 26-426-01 ADP, SHARP IR
1 26-467-01 ADP, UNV, “A”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔” IN THE “Config as” COLUMN. IF Y OUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE Y OUR SWITCHER

WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: SHARP XG (RS-232)

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 45678910Adapter

✔ XG (RS-232) 0 0 F 9 J2 ↓↓↑↓↑↓↓ ↓↑↓26-467-01

XG-E1200U 1 0 F 3 J2 ↑↓↑↓↑↓↓ ↓↑↓26-426-01
XG-1000/E1100 0 0 F 3 J2 ↑↓↑↓↑↓↓↓↑↓26-426-01

XG-NV6/NV2U/NV5 2 0 F 9 J 2 ↑↓↑↓↑↓↓ ↓↑↓26-467-01
XG-NV3 1 0 F 9 J2 ↑↓↑↓↑↓↓ ↓↑↓26-467-01

XG-P10XU 2 0 F 9 J 2 ↑↓↑↓↑↓↓ ↓↑↓26-467-01
PG-C30XU 2 0 F 9 J2 ↑↓↑↓↑↓↓ ↓↑↓26-467-01

XG-P20XU 1 0 F 9 J 2 ↑↓↑↓↑↓↓ ↓↑↓26-467-01

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C

Page 1

Sharp Installation Configuration and Connections

Sharp XG Series Projector Configuration (RS-232)

Verify that the System 8/10 Plus is already configured for the Sharp XG Series
projector by following the procedure and switch settings below. The general
setup is explained on page 3-4 of your System 8/10 Plus User’s Manual.

1. Use a small screwdriver to remove the access cover from the System 8/10 Plus
front panel. Refer to page 3-3 of the User’s Manual.

_________ Before changing anything, remove the AC power cord to the System 8/10 Plus

and also turn the projector’s power OFF.

2. Set the System 8/10 Plus switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Sharp XG (RS-232) 0 0 F 9 J2 ↓↓↑↓ ↑↓ ↓↓¯↑↓ 26-467-01

4

2

ON

RS2

3456 789101

SW15 DIP Switch

RS3

RS4

RS1

RS5 RS2

RS1

Configured For:

RS-232

RS3 RS4

3. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and
the others in the down position. See illustration on the left.

4. Use the illustration on the following page and continue with the steps below.

5. Connect the BNC cables from the System 8/10 Plus outputs to the projector
inputs according to the application requirements (RGBS, S-Video or Composite
Video).

________ The projector’s RGB BNC input will not accept rates lower than VGA or higher

than XGA. Please refer to your projector user manual.

________ Some Sharp projectors will only select S-Video when connected to an S-Video

Extron • System 8/10 P

source. You should not input S-Video and Composite Video sources
simultaneously on these models. Consult your Sharp manual to determine if
your model supports CVID and SVID simultaneously.

6. Apply Main Power to the System 8/10 Plus by connecting the power cord. The
Main Power LED should light. Apply power to the projector.

7. Installation is now completed.

LUS

• User’s Manual • P/N 68-409-01 Rev. C

Page 2

Sharp Installation Configuration and Connections

WIRED

REMOTE

COMPUTER

AUDIO IN

FOR PC98MOUSE

PC CONTROL

INPUT 1 OUTPUT

COMPUTER RGB AUDIO OUTPUT

LR

R

G

BH V

INPUT 2

DC5V OUTPUT

-

MAX CURRENT 1A

+

VIDEO INPUT AUDIO INPUT

VIDEO OUTPUT

S-VIDEO

VIDEO

LR

FILTER

ON

OFF

VIDEO INPUT

S-VIDEO

VIDEO

IN
1

IN
2

RGBHV 5 BNC

9-Pin Female

Universal

CommAdapter

26-467-01

15-Pin
Male

DO NOT
CONNECT
HERE

Composite

Video

or

S-Video

9-Pin Male

Composite

Video

and

S-Video

CONNECT
HERE

Composite

Video

or

S-Video

System 8/10 Plus to Sharp XG Series Projector Connections (RS-232)

Use the illustration below as a guide when connecting the System 8/10 Plus to a
Sharp projector. Refer to Sharp documentation to continue the installation.

________ Important note! For Sharp projectors which do not allow simultaneous

connections to S-Video and Composite Video (see last note on previous page),
please refer to the following diagram where either S-Video or Composite Video
may be connected, but not both at the same time. For those Sharp projectors
which will allow you to connect to S-Video and Composite Video sources
simultaneously - please refer to the inset diagram below.

________ When RS-232 control of the projector is used, the projector’s IR remote can be

used. However, because the projector’s IR remote does not communicate with
the System 8/10 Plus switcher, the projector and switcher can become out-of­sync if the projector’s IR remote is used to change the projector’s input, picture
mute or power settings. Should this occur, press the power, mute or channel
buttons on the switcher to allow the projector and switcher to resynchronize.

________ If the installation includes looping (master/slave) switchers, see Chapter 5 of the

System 8/10 Plus User’s Manual.

________ If Video Loop Back is part of the installation, refer to pages 2-10 and 2-11.

Extron • System 8/10 P

LUS

• User’s Manual • P/N 68-409-01 Rev. C

Page 3

Sharp Installation Configuration and Connections

Sharp XG-1000/E1100 Projector Configuration

Verify that the System 8/10 PLUS is already configured for the Sharp projector.
The general setup is explained on page 3-4 and the switch settings for the Sharp
projector are repeated below.

1. Use a small screwdriver to remove the access cover from the System 8/10 PLUS
front panel. See bottom of page 3-3. The label on the back of the access cover
also has the configuration information.

__________ Before changing anything, remove the AC power cord to the System 8/10 P

to verify that the main power is OFF; also turn the projector power OFF.

2. Set the switches as follows:

Config Model Rotary Switches Cable SW15 Settings Comm

as RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter

Sharp XG 0 0 F 3 J2 ↑↓ ↑ ↓↑↓ ↓ ↓¯↑↓ 26-426-01

4

2

3456 789101

SW15 DIP Switch

RS3 RS4

RS3

RS4

_ RS5 is for

RGB switching
delay. See
page 3-4 for
more
information.

RS2

RS1

RS5 RS2

RS1

ON

Configured For:

RS-232

LUS

Extron • System 8/10 P

3. Use a grease pencil (or other rub-off marker) to mark the space on the label next
to “Sharp XG”.

4. Locate the switcher’s Address DIP switches on the rear panel, lower right.
Unless this is part of a master/slave system, set #3 and #5 to the up position and
the others down. See picture to the left.

Use the illustration on the next page to do the following steps.

5. Connect the Comm Adapter’s miniphone connector to the “Wired Remote” input
jack and the power plug to the Aux power port on the rear panel of the projector.

6. Connect the CC-50' (or CC-100') cable from the 9-pin male connector of the
Comm Adapter to the 15-pin HD “Projector Control” port located on the rear
panel of the System 8/10 PLUS. (If you wish to make your own communications
cable, see page 3-2.)

______ Secure the screws on all D connectors.

7. Connect the BNC cables from the System 8/10 PLUS outputs to the Sharp
projector inputs according to the application requirements.

8. Apply Main Power to the System 8/10 PLUS by connecting the power cord. The
Main Power LED should light. Apply power to the projector.

9. Return System 8/10 PLUS and projector to normal operation.

LUS

• User’s Manual • P/N 68-409-01 Rev. C

Page 4