Sharp 19C140 - 19"" CRT TV, 19C140 Service Manual

19C140

SERVICE MANUAL

COLOR TELEVISION

Chassis No. CD-A

MODELS

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.

19C140

CONTENTS

Page

» ELECTRICAL SPECIFICATIONS......................................................................................................... 1

» IMPORT ANT SERVICE SAFETY PRECAUTION................................................................................. 2

»LOCATION OF USER'S CONTROL.....................................................................................................4

»INSTALLATION AND SERVICE INSTRUCTIONS................................................................................5

»CHASSIS LAYOUT............................................................................................................................10

»BLOCK DIAGRAM.............................................................................................................................11

»SCHEMATIC DIAGRAMS..................................................................................................................12

»PRINTED WIRING BOARD ASSEMBLIES........................................................................................15

»REPLACEMENT PARTS LIST...........................................................................................................18

»PACKING OF THE SET.....................................................................................................................23

ELECTRICAL SPECIFICATIONS

POWER INPUT................................120 V AC 60 Hz

POWER RATING .............................................69 W

PICTURE SIZE.......................1,194cm

CONVERGENCE........................................Magnetic

SWEEP DEFLECTION................................Magnetic

FOCUS...........................Hi-Bi-Potential Electrostatic

INTERMEDIATE FREQUENCIES

Picture IF Carrier Frequency ................. 45.75 MHz

Sound IF Carrier Frequency .................. 41.25 MHz

Color Sub-Carrier Frequency ................ 42.17 MHz

SHARP CORPORATION

2 (185sq inch)

(Nominal)

AUDIO POWER

OUTPUT RATING...........1.0 W (at 10% distortion)

SPEAKER

SIZE .................................................. 8 cm (Round)

VOICE COIL IMPEDANCE...........8 ohm at 400 Hz

ANTENNA INPUT IMPEDANCE

VHF/UHF................................ 75 ohm Unbalanced

TUNING RANGES

VHF-Channels.......................................... 2 thru 13

UHF-Channels........................................ 14 thru 69

CATV Channels...................................... 1 thru 125

(EIA, Channel Plan U.S.A.)

Specifications are subject to change without
prior notice.

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

19C140

IMPORT ANT SER VICE SAFETY PRECAUTION

Ë

Service work should be performed only by qualified service technicians who are thoroughly
familiar with all safety checks and the servicing guidelines which follow:

WARNING

1. For continued safety, no modification of any circuit
should be attempted.

2. Disconnect AC power before servicing.

3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.

4. The chassis in this receiver has two ground systems
which are separated by insulating material. The non­isolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.

CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE

4A 125V

ONLY WITH SAME TYPE 4A­125V FUSE.

SERVICING OF HIGH VOL T AGE SYSTEM
AND PICTURE TUBE

When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the pic­ture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)

1. Picture tube in this receiver employs integral
implosion protection.

2. Replace with tube of the same type number for
continued safety .

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely .

X-RADIA TION AND HIGH VOL TAGE LIMITS

1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation.
The only potential source of X-ray in current solid
state TV receivers is the picture tube. However, the
picture tube does not emit measurable X-Ray
radiation, if the high voltage is as specified in the
"High Voltage Check" instructions.
It is only when high voltage is excessive that X­radiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.

2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.

3. High voltage should always be kept at the rated value

-no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.

4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem.
Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly .

5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry .

6. When troubleshooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.

2

2
2

IMPORTANT SERVICE SAFETY PRECAUTION

(Continued)

19C140

BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)

Before returning the receiver to the user, perform
the following safety checks.

1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators and etc.

3. To be sure that no shock hazard exists, check for
leakage current in the following manner.

» Plug the AC cord directly into a 120 volt AC outlet,

(Do not use an isolation transformer for this test).

» Using two clip leads, connect a 1.5k ohm, 10 watt

resistor paralleled by a 0.15mF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.

» Use an AC voltmeter having with 5000 ohm per volt,

or higher, sensitivity to measure the AC voltage drop
across the resistor.

» Connect the resistor connection to all exposed metal

parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon and etc.) and measure the AC voltage
drop across the resistor.
AII checks must be repeated with the AC ine cord
plug connection reversed. (If necessary, a non­polarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.

1.5k ohm
10W

0.15µF

TEST PROBE

TO EXPOSED
METAL PARTS

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

CONNECT TO
KNOWN EARTH
GROUND

SAFETY NOTICE

Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage and etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.

3

19C140

LOCATION OF USER'S CONTROL

4

19C140

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic

screwdrivers or TV alignment tools.

(2)Before performing adjustments, the TV set must be on at least 15 minutes.

CIRCUIT PROTECTION

The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.

X-RADIA TION PROTECTOR CIRCUIT TEST

After service has been performed on the horizontal
deflection system, high voltage system, +B system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:

1) Apply 120V AC using a variac transformer for
accurate input voltage.

2) Allow for warm up and adjust all customer controls
for normal picture and sound.

3) Receive a good local channel.

4) Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 21.3 ±1.5 V.

5) Apply external 28.9V DC at TP653 by using an
external DC supply, TV must be shut off.

6) T o reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.

7) If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before
the set is returned to the customer.

HIGH VOL T AGE CHECK

High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:

1. Connect an accurate high voltage meter between
ground and anode of picture tube.

2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly
tuned in test signal.

3. Enter the service mode and select the service
adjustment "S19" and Bus data "01" (Y-mute on).

4. The voltage should be approximately, 26.0kV (at zero
beam).
If a correct reading cannot be obtained, check
circuitry for malfunctioning components. After the
voltage test, make Y-mute off to the normal mode.

5

19C140

For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.

Note: There are still a few analog adjustments in this series such as focus and master screen voltage.

Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if serv­ice adjustments are required.

1. Service mode

Before putting unit into the service mode, check that
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to
ensure customer controls are in their proper (reset)
position.

2. Service number selection

Once in the service mode, press the Ch-up or Ch­down button on the remote controller or at the set.
The service adjustment number will vary in
increments of one, from "S01" to "OP". Select the
item you wish to adjust.

3. Data number selection

Press the Vol-up or down button to adjust the data
number.

DATA NUMBER

SERVICE ADJUSTMENT NUMBER

To enter the service mode and exit service
mode.

While pressing the Vol-up and Ch-up buttons at the
sametime, plug the AC cord into a wall socket.
Now the TV set is switched on and enters the service
mode.
To exit the service mode, turn the television off by
pressing the power button.

CHANNEL

S01

Figure A.

55(085)

02

S01 D:00

6

19C140

SERVICE

NUMBER

S01 PICTURE 55 00-7F
S02 TINT 46 00-7F
S03 COLOR 32 00-7F
S04 BRIGHTNESS 40 00-7F
S05 SHARPNESS 28 00-3F Must be set to "24"
S06 VERTICAL PHASE 00 00-07 Must be set to "00" ~ "03"
S07 HORIZONTAL PHASE 12 00-1F
S08 RF-AGC 23 00-3F
S09 VERTICAL AMP 20 00-3F
S10 VCO 2C 00-7F
S11 R CUT-OFF 00 00-FF
S12 G CUT -OFF 00 00-FF
S13 B CUT-OFF 00 00-FF
S14 G GAIN 7F 00-FF
S15 B GAIN 7F 00-FF
S16 TRAP(3.58MHz) 00 00 or 01 Must be set to "00"
S17 BALANCE 20 00-3F Must be set to "20"
S18 C.C.POSITION 17 00-7F
S19 Y-MUTE 00 00,01,03
S20 ENERGY SA VE OFFSET 20 00-3F Must be set to "23"
S21 D.D.E. OFFSET 03 00-1F Must be set to "03"
S22 OSD SETUP 00 00-03 Must be set to "00"
S23 TUNER SETUP 00 00-01 Must be set to "00"
OP OPTION 30 00-FF Must be set to "02"

ADJUSTMENT ITEM

INITIAL VALUE

DATA

ADJUSTMENT CONTENTS

RANGE

"00" = NORMAL, "01" = No Y, "03" = No VERTICAL

Table - A

Holding down both the CH-up/down buttons on the TV set at service mode for more than 2 seconds will automatically
write the above initial values into IC2101.

PART REPLACED

IC2001

IC201

IC2101 X

CRT X

ADJUSTMENT

NECESSARY

X

UNNECESSARY

X

Data is stored in IC2101.
The adjustment is needed to compensate for characteristics

of parts including IC201.

Holding down both the CH-up/down buttons on the TV set in
the service mode for more than 2 seconds will automatically
write the above initial values into IC2101.

Adjust items related to picture tube only.

NOTES

Table - B

7

19C140

Ë

SERVICE ADJUSTMENT

VCO Adjustment

1. Connect a digital voltmeter between pin (44) of IC201
and ground.

2. Receive a good local channel.

3. Enter the service mode and select the service
adjustment "S10".

4. Adjust the data so that digital voltmeter reads 2.2V.

5. Adjustment is completed, remove the voltmeter,
return to "normal" mode.

RF AGC Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service
adjustment "S08".

3. Set the data value to point where no noise or beat
appears.

4. Select another channel to confirm that no noise or
beat appears.
Note 1: You will have to come out of the service

mode to select another channel.

Note 2: Setting the data to "00" will produce a black

raster.

White Balance Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service
adjustment "S03" and set to "00" (minimum
color)(Record original data code under adjustment
"S03" before changing). "S03" does not have to be
adjusted, if you selected a B/W picture or monoscope
pattern.

3. Alternately adjust the service adjustment data of
"S14" and "S15" until a good grey scale with normal
whites is obtained.

4. Select the service adjustment "S03" and adjust data
to obtain normal color level.

Sub-Picture Adjustment

1. Receive a good local channel.

2. Make sure the customer picture control is set to
maximum.

3. Enter the service mode and select the service
adjustment "S01".

4. Adjust the data value to achieve normal contrast
range.

Screen Adjustment

1. Connect a digital voltmeter between TP852 and
TP853 on the CRT Unit.
Note: These test points may not be provided.

Then connect the voltmeter to both ends of
R852 located near Q852 on the foil side.

2. Receive a good local channel.

3. Enter the service mode and select the service
adjustment "S03" and set the data value to "00" to
set the color level to minimum. (Record original data
code under adjustment "S03" before changing) You
may skip this step, if you selected a B/W picture or
monoscope pattern.

4. Select the service adjustment "S19" and adjust the
data value to "01", this turn off the luminance signal
(Y -mute).

5. Select the service adjustment "S04" and adjust data
value to obtain 0.17 volts on the digital voltmeter.

6. Adjust the master screen cotrol until the raster
darkens to the point where raster is barely seen.

7. Adjust the service adjustments "S11" red, "S12"
green and "S13" blue to obtain a good grey scale
with normal whites at low brightness level.

8. Select the service adjustment "S19" and reset data
to "00". Select the service adjustment "S03" and reset
data to obtain normal color level.

9. Remove digital voltmeter, and reset the master
screen control to obtain normal brightness range.

Sub-Tint Adjustment

1. Receive a good local channel.

2. Set customer tint control to center of it's range.

3. Enter the service mode and select the service
adjustment "S02".

4. Adjust "S02" data value to obtain normal flesh tones.

Sub-Color Adjustment

1. Receive a good local channel.

2. Make sure the customer color control is set to center
position .

3. Enter the service mode and select service
adjustment "S03".

4. Adjust "S03" data value to obtain normal color level.

8

DESCRIPTION OF SCHEMATIC DIAGRAM

19C140

NOTES:

1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)

2. All resistors are 1/10 watt, unless otherwise noted.

3. All capacitors are µF, unless otherwise noted.
(P=pF=µµF)

4. (G) indicates ±2% tolerance may be used.

5. indicates line isolated ground.

VOLTAGE MEASUREMENT CONDITIONS:

1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set f or normal
picture unless otherwise indicated.

2. All voltages measured with 1000µV B & W or Color
signal.

WAVEFORMS

1.0

1.0

0.9

WAVEFORM MEASUREMENT CONDITIONS:

1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.

2.

indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)

å

AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.

'

MARK= X-RAY RELATED PARTS.

This circuit diagram is a standard one, printed
circuits may be subject to change for product
improvement without prior notice.

5.0

5.0

2.1

1.0

1.2

1160

1.4

25

220

105

47

150

95

4.6

133

105

0.7

220

33

1.7

39.0

0.7

9

19C140

CHASSIS LAYOUT

H

G

F

E

NORMAL

D

PR701

C708

C

B

A

654321

10

BLOCK DIAGRAM

H

G

F

19C140

E

D

C

B

A

654321

11

19C140

SCHEMATIC DIAGRAM: MAIN-1 Unit

H

G

F

E

D

C

B

A

87 109654321

12

19C140

1716 1918151413121110

13

19C140

H

G

F

SCHEMATIC DIAGRAM: CRT Unit

E

D

C

B

A

654321

14

PRINTED WIRING BOARD ASSEMBLIES

H

G

F

19C140

E

D

C

B

PWB-A: MAIN Unit (Wiring Side)

A

654321

15

19C140

H

\

G

F

\r

\r

\n

\r\r

\r

\

\r

\r

\r

\r

\

\r

\

\

\

\

\

\

E

\

\r

\n

\n

\n

\

\n

\

\f

\f

\

\

\

\

\n

\

\

\

\

\

\

\

\

\

\

\n

\n

\n

\b

\b\b\b

\n

\b

\r

\r\

\r\

\n

\n

\n

\n

\n

\n

\n

\f\f\f

\

\

\b\b\b

\b\r\r

\

\n

\n\r\n

\b

\f

\n

\n

\n

\n

\n

\n

\n

\n\n

\

\n

\n

\r\n\r

\n\

\

\

\

\

\

\\

\n\

\

\

\

\n

\n

\f

\f

\f

\f

\f

\f

\f

\

\f

\

\

\

\f

\f

D

\

\

\

\b

\n\n\n

C

\n

\

\f

\r

\n\n\n

\n

\

\

\

B

PWB-A: MAIN Unit (Chip Parts Side)

A

654321

16

19C140

H

G

F

PWB-B: CRT Unit (Wiring Side)

E

D

\b

\b

\b\\b\\b

C

B

\b\

\b\

\b\

\b

\b

\b

\b

\b

\b\

\b\

\b\b

PWB-B: CRT Unit (Chip Parts Side)

A

654321

17

19C140

Ref. No. Part No. « Description Code

PARTS LIST

PARTS REPLACEMENT

Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.

"HOW TO ORDER REPLACEMENT PARTS"

To have your order filled promptly and correctly, please furnish the
following informations.

1. MODEL NUMBE

3. PART NO.4. DESCRIPTION

in USA:Contact your nearest SHARP Parts Distributor to order.

For location of SHARP Parts Distributor, Please call Toll­Free; 1-800-BE-SHARP

« MARK: SPARE PARTS-DELIVERY SECTION

p

Ref. No. Part No. « Description Code

pU V101 VB48JLL40X/*S X BR

U L703 RCILG0099PEZZ X Degaussing coil (19v) AF

pU DY601 RCILH0105GJZZ X DY (20V) AQ

QEARC2016PEZZ X Earth Parts AC
PMAGF3045CEZZ X Purity Magnet AC
PSPAG0012MEZZ X WEDGE AB
LHLDW0102GJKZ X WIRE TIE (20 .32 cm) AB
LHLDW1007MEKZ X WIRE TIE (36 .4 cm) AB

PRINTED WIRING BOARD ASSEMBLIES

(NOT REPLACEMENT ITEM)

DUNTKA358WEW9 — MAIN Unit —
DUNTKA359WEW0 — CRT Unit —

R2. REF. NO.

MARK: X-RAY RELATED PARTS

PICTURE TUBE

CRT 19V (Orion)

PWB-A: DUNTKA358WEX9

MAIN UNIT

NOTE:THE PARTS HERE SHOWN ARE SUPPLIED AS AN

ASSEMBLY BUT NOT INDEPENDETLY

U TU51 VTUVT1T5UF214 X TUNER AP

pU IC201 RH-IX3354CEN1 X IX3354CE AM

IC351 VHIAN7511//-1 X AN7511 AC

U IC501 VHILA7840//-1 X LA7840 AE
U IC701 VHITEA1507/-1 X TEA1507 AE
U IC702 RH-FX0034CEZZ X FX0034CE AB
U IC771 VHIKA7805AP-1 X KA7805AP AC

IC2001 RH-IX3492CEZZQ X IX3492CE AN
IC2040 VHIPST994C/-1+ X PST994C AB
IC2102 VHIBR24L16F-1Y X BR24L16F AC

Q101 VS2SC945AQ/-1+ X 2SC945AQ AB
Q201 VS2SC2735//1EY X 2SC2735 AB
Q451 VS2SA1530R/-1Y X 2SA1530R AB
Q452 VS2SA1266-Y-1+ X 2SA1266(Y) AB
Q601 VS2SC2482//-1+ X 2SC2482 AB

U Q602 VS2SD2586//1E X 2SD2586 AF

Q631 VS2SC945AQ/-1+ X 2SC945AQ AB

U Q701 VSSPA04N603-1 X SPA04N603 AF

Q702 VS2SC945AQ/-1+ X 2SC945AQ AB
Q751 VS2SC945AQ/-1+ X 2SC945AQ AB
Q752 VS2SC945AQ/-1+ X 2SC945AQ AB
Q2201 VS2SD601AR/-1Y X 2SD601AR AB
Q2211 VS2SD601AR/-1Y X 2SD601AR AB

D52 RH-EX0676GEZZY X Zener Diode 32V AB
D101 RH-EX0617GEZZY X Zener Diode 5.6V AB
D352 VHD1SS119//-1Y X Diode AA
D353 RH-EX0644GEZZY X Zener Diode 13V AB

U D453 RH-EX0616GEZZY X Zener Diode 5.6V

D455 VHD1SS119//-1Y X Diode AA
D456 RH-DX0475CEZZY X Diode AB
D457 RH-EX0644GEZZY X Zener Diode 13V AB
D458 RH-EX0644GEZZY X Zener Diode 13V AB
D459 VHD1SS119//-1Y X Diode AA
D502 RH-DX0131CEZZY X Diode AB
D511 RH-DX0441CEZZY X Diode AB
D632 RH-EX0630GEZZY X Zener Diode 9.1V AB
D641 RH-EX0630GEZZY X Zener Diode 9.1V AB

p U

D651 VHD1SS244//-1Y X Diode AB

p U

D653 RH-EX0667GEZZY X Zener Diode 27V AB

D661 RH-DX0468CEZZ X Diode AB

U

D701 RH-DX0490CEZZY X Diode AB

U

D702 RH-DX0490CEZZY X Diode AB

U

D703 RH-DX0490CEZZY X Diode AB

U

D704 RH-DX0490CEZZY X Diode AB

D707 VHD1SS119//-1Y X Diode AA
D708 VHD1SS119//-1Y X Diode AA
D709 RH-DXA006WJZZ X Diode AB
D712 RH-DX0487CEZZY X Diode AB
D717 RH-EX0616GEZZY X Zener Diode 5.6V AB
D725 RH-DX0131CEZZY X Diode AB
D726 VHD1SS119//-1Y X Diode AA
D751 RH-EX0611GEZZY X Zener Diode 5.1V AB
D752 RH-DX0441CEZZY X Diode AB
D753 RH-DX0441CEZZY X Diode AB
D757 VHD1SS119//-1Y X Diode AA
D758 RH-DX0131CEZZY X Diode AB

U PR702 RMPTP0092CEZZ X Packaged Circuit AD

X801 RCRSAA010WJZZ X Crystal AB
VA701 RH-VXA009WJZZ X Varistor AB
CF2040 RFILA0099CEZZ+ X FILTER AB
SF201 RFILC0441CEZZ X SAW Filter AD

TUNER

INTEGRATED CIRCUITS

TRANSISTORS

DIODES

AB

PACKAGED CIRCUITS

18

19C140

Ref. No. Part No. « Description Code

PWB-A: DUNTKA358WEX9

MAIN UNIT (Continued)

CONTROL

R738 RVR-M4588CEZZ+ X 22k 130V Adj. AB

CAPACITORS

[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]

C51 VCEA0A1AW337M+ X 330 10V EL. AB
C53 VCEA0A1HW105M+ X 1 50V EL. AB
C54 VCEA0A1HW475M+ X 4.7 50V EL. AB
C55 VCEA0A1AW107M+ X 100 10V EL. AB
C101 VCEA0A1CW476M+ X 47 16V EL. AB
C201 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C202 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C203 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C204 VCQYTA1HM223J+ X 0.022 50V Mylar AB
C205 VCKYPA1HB103K+ X 0.01 50V Ceramic AB
C206 VCKYCY1HB102KY X 1000p 50V Ceramic AA

C207 VCEA0A1CW476M+ X 47 16V EL. AB
C208 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C209 VCEA0A1HW105M+ X 1 50V EL. AB
C210 VCEA0A1HW474M+ X 0.47 50V EL. AB
C212 VCEA0A1HW474M+ X 0.47 50V EL. AB
C220 VCKYCY1CB104KY X 0.1 16V Ceramic AA
C301 VCCCCY1HH220JY X 22p 50V Ceramic AA
C302 VCKYCY1HB102KY X 1000p 50V Ceramic AA
C304 VCCCCY1HH220JY X 22p 50V Ceramic AA
C305 VCKYCY1HB103KY X 0.01 50V Ceramic AA
C306 VCQYTA1HM103J+ X 0.01 50V Mylar AB
C354 VCEA0A1HW225M+ X 2.2 50V EL. AB
C356 VCKYCY1HB332KY X 3300p 50V Ceramic AA
C357 VCEA0A1HW106M+ X 10 50V EL. AB
C358 VCEA0A1HW106M+ X 10 50V EL. AB
C361 VCEA0A1CW227M+ X 220 16V EL. AB
C401 VCCCCY1HH470JY X 47p 50V Ceramic AA
C411 VCEA0A1AW108M+ X 1000 10V EL. AB
C412 VCKYCY1HB103KY X 0.01 50V Ceramic AA
C414 VCEA0A1HW225M+ X 2.2 50V EL. AB
C416 VCEA0A1HW105M+ X 1 50V EL. AB
C418 VCKYCY1HB103KY X 0.01 50V Ceramic AA
C421 VCEA0A1HW106M+ X 10 50V EL. AB
C451 VCQYTA1HM563J+ X 0.056 50V Mylar AB
C454 VCEA0A1HW475M+ X 4.7 50V EL. AB
C455 VCEA0A1CW226M+ X 22 16V EL. AB
C456 VCEA0A1HW475M+ X 4.7 50V EL. AB
C509 VCKYPA2HB102K+ X 1000p 500V Ceramic AB
C510 VCEA0A1VW477M+ X 470 35V EL. AB
C512 VCFYSA1JB224J+ X 0.22 63V Mylar AB
C513 VCFYSA1JB473J+ X 0.047 63V Mylar AB
C514 VCEA0A1EW477M+ X 470 25V EL. AB
C515 VCEA0A1HW475M+ X 4.7 50V EL. AB
C516 VCKYCY1HB222KY X 2200p 50V Ceramic AA
C517 VCEA0A1CW226M+ X 22 16V EL. AB
C520 VCEA0A1HW107M+ X 100 50V EL. AB
C530 VCFYFA1HA334J+ X 0.33 50V Mylar AB
C531 VCFYFA1HA564J+ X 0.56 50V Mylar AB
C606 VCKYPA2HB561K+ X 560p 500V Ceramic AB
C607 VCKYPA1HB472K+ X 4700p 50V Ceramic AB

pU C610 VCFPVC3ZA772H X 7700p 1.5kV M-Poly. AB

C612 VCFPVC2DB474J X 0.47 200V M-Poly. AB
C633 VCEA0A1AW337M+ X 330 10V EL. AB
C634 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C635 VCEA0A1HW105M+ X 1 50V EL. AB
C636 VCQYTA1HM153J+ X 0.015 50V Mylar AB
C637 VCEA0A1CW476M+ X 47 16V EL. AB
C652 VCEA0A1HW475M+ X 4.7 50V EL. AB
C653 VCEA0A1HW105M+ X 1 50V EL. AB
C661 VCKYPA2HB152K+ X 1500p 500V Ceramic AB
C662 VCEA0A1CW477M+ X 470 16V EL. AB
C701 RC-FZ036SCEZZ X 0.1mF AC125V Plastic AB
C702 RC-KZ0029CEZZ+ X 0.01 AC250V Ceramic AB
C703 RC-KZ0029CEZZ+ X 0.01 AC250V Ceramic AB
C705 RC-EZ0718CEZZ X 470 200V EL. AE

Ref. No. Part No. « Description Code

C706 RC-KZ0092GEZZA X 3300p AC250V Ceramic AB
C717 VCKYPA2HB472K+ X 4700p 500V Ceramic AB
C723 RC-EZ0638CEZZ X 33 160V EL. AC
C725 RC-EZ0724CEZZ X 100 160V EL. AC
C726 VCKYPH3DB561K X 560p 2kV Ceramic AB
C727 VCKYPA2HB472K+ X 4700p 500V Ceramic AB

U C730 VCEA0A1CW108M+ X 1000 16V EL. AB

C731 VCEA0A1EW107M+ X 100 25V EL. AB
C732 VCKYPA1HF103Z+ X 0.01 50V Ceramic AA
C735 VCCCPA1HH680J+ X 68p 50V Ceramic AA
C737 VCEA0A1EW226M+ X 22 25V EL. AB
C738 RC-KZ0040CEZZ X 820p 2kV Ceramic AB
C739 VCEA0A1HW104M+ X 0.1 50V EL. AB
C740 VCEA0A1EW476M+ X 47 25V EL. AB
C743 VCKYPH3DB561K X 560p 2kV Ceramic AB
C750 VCKYPA1HF103Z+ X 0.01 50V Ceramic AA
C752 VCEA0A1CW476M+ X 47 16V EL. AB
C754 VCEA0A1CW476M+ X 47 16V EL. AB
C758 VCEA0A2EW106M+ X 10 250V EL. AB
C759 VCKYPA2HB102K+ X 1000p 500V Ceramic AB
C760 VCEA0A1CW108M+ X 1000 16V EL. AB
C771 VCEA0A1CW476M+ X 47 16V EL. AB
C772 VCEA0A1CW476M+ X 47 16V EL. AB
C783 VCQYTA1HM103J+ X 0.01 50V Mylar AB
C801 VCCCCY1HH180JY X 18p 50V Ceramic AA
C802 VCEA0A1CW106M+ X 10 16V EL. AB
C807 VCKYCY1EF104ZY X 0.1 25V Ceramic AA
C808 VCEA0A1CW106M+ X 10 16V EL. AB
C809 VCEA0A1HW105M+ X 1 50V EL. AB
C811 VCKYCY1CB473KY X 0.047 16V Ceramic AA
C812 VCEA0A1HW474M+ X 0.47 50V EL. AB
C901 VCEA0A1HW105M+ X 1 50V EL. AB
C905 VCEA0A1HW106M+ X 10 50V EL. AB
C2001 VCCCCY1HH101JY X 100p 50V Ceramic AA
C2002 VCKYCY1HF103ZY X 0.01 50V Ceramic AA
C2040 VCEA0A1AW107M+ X 100 10V EL. AB
C2041 VCEA0A1HW105M+ X 1 50V EL. AB
C2060 VCKYCY1CB104KY X 0.1 16V Ceramic AA
C2061 VCKYCY1HB222KY X 2200p 50V Ceramic AA
C2062 VCEA0A1AW107M+ X 100 10V EL. AB
C2201 VCKYCY1HB682KY X 6800p 50V Ceramic AA
C2202 VCCCCY1HH560JY X 56p 50V Ceramic AA
C2601 VCEA0A0JW107M+ X 100 6.3V EL. AB
C2602 VCCCCY1HH101JY X 100p 50V Ceramic AA

RESISTORS

[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]

RJ2 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ7 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ8 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ9 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ10 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ12 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ18 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ19 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ20 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
RJ21 VRS-CY1JF000JY X 00 1/16W M-Ox. AA

U R53 VRS-RG3LB223J+ X 22k 3W M-Ox. AB

R54 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R55 VRS-CY1JF101JY X 100 1/16W M-Ox. AA

R56 VRS-CY1JF823JY X 82k 1/16W M-Ox. AA
R57 VRD-RA2BE563JY X 56k 1/8W Carbon AA
R101 VRD-RA2BE152JY X 1.5k 1/8W Carbon AA
R201 VRS-CY1JF221JY X 220 1/16W M-Ox. AA
R202 VRS-CY1JF122JY X 1.2k 1/16W M-Ox. AA
R203 VRS-CY1JF682JY X 6.8k 1/16W M-Ox. AA
R204 VRS-CY1JF270JY X 27 1/16W M-Ox. AA
R205 VRD-RA2BE680JY X 68 1/8W Carbon AA
R206 VRD-RA2EE151JY X 150 1/4W Carbon AA
R207 VRD-RA2BE223JY X 22k 1/8W Carbon AA
R208 VRS-CY1JF332JY X 3.3k 1/16W M-Ox. AA

19

19C140

Ref. No. Part No. « Description Code

PWB-A: DUNTKA358WEX9

MAIN UNIT

RESISTORS

[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]

R209 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R210 VRS-CY1JF104JY X 100k 1/16W M-Ox. AA
R211 VRS-CY1JF104JY X 100k 1/16W M-Ox. AA
R212 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R215 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R220 VRS-CY1JF331JY X 330 1/16W M-Ox. AA
R301 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R302 VRS-CY1JF152JY X 1.5k 1/16W M-Ox. AA
R353 VRD-RA2BE683JY X 68k 1/8W Carbon AA
R354 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R355 VRD-RA2BE223JY X 22k 1/8W Carbon AA
R357 VRS-CY1JF822JY X 8.2k 1/16W M-Ox. AA
R401 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R402 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R403 VRS-CY1JF101JY X 100 1/16W M-Ox. AA

R404 VRD-RA2BE102JY X 1k 1/8W Carbon AA
R411 VRS-CY1JF684JY X 680k 1/16W M-Ox. AA
R412 VRS-CY1JF391JY X 390 1/16W M-Ox. AA
R413 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R414 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R421 VRS-CY1JF223JY X 22k 1/16W M-Ox. AA

U R451 VRS-RG2HC103J+ X 10k 1/2W M-Ox. AB

R453 VRD-RA2BE152JY X 1.5k 1/8W Carbon AA
R454 VRD-RA2EE334JY X 330k 1/4W Carbon AA
R455 VRD-RA2BE392JY X 3.9k 1/8W Carbon AA
R456 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA

R457 VRD-RA2BE102JY X 1k 1/8W Carbon AA
R458 VRD-RA2EE334JY X 330k 1/4W Carbon AA
R460 VRD-RA2BE152JY X 1.5k 1/8W Carbon AA
R461 VRS-CY1JF184JY X 180k 1/16W M-Ox. AA
R462 VRS-CY1JF273JY X 27k 1/16W M-Ox. AA
R495 VRS-RG3DB820J+ X 180k 1/16W M-Ox. AB
R512 VRD-RM2HD102JY X 1.0k 1/2W Carbon AA
R513 VRD-RM2HD102JY X 1.0k 1/2W Carbon AA
R514 VRD-RM2HD1R0JY X 1 1/2W Carbon AA
R515 VRS-RG3AB391J+ X 390 1W M-Ox. AB
R516 VRS-CY1JF153JY X 15k 1/16W M-Ox. AA
R517 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R518 VRS-CY1JF333JY X 33k 1/16W M-Ox. AA
R519 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R520 VRD-RM2HD1R5JY X 1.5 1/2W Carbon AA
R522 VRD-RA2BE102JY X 1k 1/8W Carbon AA
R523 VRD-RA2BE562JY X 5.6k 1/8W Carbon AA
R525 VRD-RA2BE272JY X 2.7k 1/8W Carbon AA
R527 VRD-RA2BE223JY X 22k 1/8W Carbon AA
R528 VRD-RA2BE272JY X 2.7k 1/8W Carbon AA
R529 VRD-RA2BE472JY X 4.7k 1/8W Carbon AA

U R604 VRS-RG3DB682J+ X 6.8k 2W M-Ox. AB

R605 VRD-RA2BE121JY X 120 1/8W Carbon AA
R606 VRD-RA2BE102JY X 1k 1/8W Carbon AA
R607 VRS-RG3DB682J+ X 6.8k 2W M-Ox. AB

U R608 VRS-RG3DB391J+ X 390 2W M-Ox. AB
U R609 VRS-RG3AB562J+ X 5.6k 1W M-Ox. AB

R610 VRD-RM2HD220JY X 22 1/2W Carbon AA

U R611 VRS-KA3HG3R3K X 3.3 5W M-Ox. AB

R622 VRS-CY1JF222JY X 2.2k 1/16W M-Ox. AA
R623 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R624 VRN-RA2BK472FY X 4.7k 1/8W M-Film AB
R634 VRD-RM2HD121JY X 120 1/2W Carbon AA
R635 VRS-CY1JF332JY X 3.3k 1/16W M-Ox. AA
R636 VRD-RA2EE221JY X 220 1/4W Carbon AA

U R641 VRS-RG3AB682J+ X 6.8k 1W M-Ox. AB

R651 VRD-RM2HD270JY X 27 1/2W Carbon AA

Ref. No. Part No. « Description Code

R653 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R654 VRD-RA2BE154JY X 150k 1/8W Carbon AA

p R655 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA

R659 VRN-RL3AB3R3J+ X 3.3 1W M-Film AB
R661 VRN-RL3ABR47J+ X 0.47 1W M-Film AB
R662 VRD-RA2BE102GY X 1.0k 1/8W Carbon AA

U R702 RR-DZ0049CEZZY X 3.9M 1/2W Solid AB
U R703 VRW-KP3HC1R8K X 1.8 5W Cement AB

U R705 VRN-RL3ABR39J+ X 0.39 1W M-Ox. AB
U R706 VRN-RL3ABR39J+ X 0.39 1W M-Ox. AB
U R707 VRD-RM2HD270JY X 27 1/2W Carbon AA
U R708 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
U R710 VRS-RG2HC102J+ X 1k 1/2W M-Ox. AB
U R711 VRS-CY1JF334JY X 330k 1/16W M-Ox. AA

R712 VRD-RA2BE100JY X 10 1/8W Carbon AA
R713 VRS-RG2HC122J+ X 1.2k 1/2W M-Ox. AB
R715 VRD-RA2BE150JY X 15 1/8W Carbon AA
R716 VRS-RG3AB121J+ X 120 1W M-Ox. AB

R721 VRD-RM2HD124JY X 120k 1/2W Carbon AA
R723 VRS-CY1JF000JY X 00 1/16W M-Ox. AA

R725 VRS-RG2HC821J+ X 820 1/2W M-Ox. AB
R733 VRD-RA2EE394JY X 390k 1/4W Carbon AA
R736 VRD-RM2HD184JY X 180k 1/2W Carbon AA
R739 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA
R740 VRD-RM2HD470JY X 47 1/2W Carbon AA
R741 VRN-RA2BK682FY X 6.8k 1/8W M-Film AB
R751 VRD-RA2BE821JY X 820 1/8W Carbon AA
R752 VRD-RA2BE392JY X 3.9k 1/8W Carbon AA

U R755 VRD-RM2HD151JY X 150 1/2W Carbon AA
U R758 VRS-RG2HC100J+ X 10 1/2W M-Ox. AB

R759 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA

U R773 VRS-VV3LB270J X 27 3.0W M-Ox. AB

R774 VRS-VV3LB680J X 68 3.0W M-Ox. AB
R801 VRD-RM2HD470JY X 47 1/2W Carbon AA
R807 VRS-CY1JF272JY X 2.7k 1/16W M-Ox. AA
R808 VRS-CY1JF222JY X 2.2k 1/16W M-Ox. AA
R809 VRS-CY1JF223JY X 22k 1/16W M-Ox. AA
R810 VRS-CY1JF223JY X 22k 1/16W M-Ox. AA
R901 VRD-RA2BE101JY X 100 1/8W Carbon AA
R902 VRS-CY1JF750JY X 75 1/16W M-Ox. AA
R906 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R925 VRS-CY1JF104JY X 100k 1/16W M-Ox. AA
R961 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R962 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R2001 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R2002 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2006 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2008 VRS-CY1JF472JY X 4.7k 1/16W M-Ox. AA
R2009 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R2010 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R2012 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2016 VRS-CY1JF223JY X 22k 1/16W M-Ox. AA
R2018 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2020 VRS-CY1JF223JY X 22k 1/16W M-Ox. AA
R2022 VRS-CY1JF333JY X 33k 1/16W M-Ox. AA
R2023 VRD-RA2BE223JY X 22k 1/8W Carbon AA
R2024 VRD-RA2BE682JY X 6.8k 1/8W Carbon AA
R2025 VRD-RA2BE682JY X 6.8k 1/8W Carbon AA
R2026 VRD-RA2BE682JY X 6.8k 1/8W Carbon AA
R2027 VRD-RA2BE682JY X 6.8k 1/8W Carbon AA
R2028 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R2029 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2032 VRD-RA2BE471JY X 470 1/8W Carbon AA
R2033 VRS-CY1JF684JY X 680k 1/16W M-Ox. AA
R2034 VRS-CY1JF684JY X 680k 1/16W M-Ox. AA
R2040 VRS-CY1JF102JY X 1k 1/16W M-Ox. AA
R2041 VRS-CY1JF333JY X 33k 1/16W M-Ox. AA
R2042 VRD-RA2BE101JY X 100 1/8W Carbon AA
R2043 VRD-RA2BE101JY X 100 1/8W Carbon AA
R2044 VRS-CY1JF683JY X 68k 1/16W M-Ox. AA

20

19C140

Ref. No. Part No. « Description Code

PWB-A: DUNTKA358WEX9

MAIN UNIT (Continued)

RESISTORS (Continued)

[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]

R2045 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R2047 VRS-CY1JF221JY X 220 1/16W M-Ox. AA
R2048 VRS-CY1JF562JY X 5.6k 1/16W M-Ox. AA
R2049 VRS-CY1JF333JY X 33k 1/16W M-Ox. AA
R2060 VRS-CY1JF221JY X 220 1/16W M-Ox. AA
R2061 VRS-CY1JF562JY X 5.6k 1/16W M-Ox. AA
R2062 VRS-CY1JF183JY X 18k 1/16W M-Ox. AA
R2063 VRS-CY1JF222JY X 2.2k 1/16W M-Ox. AA
R2065 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R2066 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2067 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2068 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2070 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2072 VRS-CY1JF103JY X 10k 1/16W M-Ox. AA
R2103 VRD-RA2BE101JY X 100 1/8W Carbon AA
R2104 VRD-RA2BE101JY X 100 1/8W Carbon AA
R2201 VRD-RA2BE103JY X 10k 1/8W Carbon AA
R2202 VRD-RA2BE473JY X 47k 1/8W Carbon AA
R2203 VRS-CY1JF332JY X 3.3k 1/16W M-Ox. AA
R2211 VRD-RA2BE222JY X 2.2k 1/8W Carbon AA
R2212 VRS-CY1JF682JY X 6.8k 1/16W M-Ox. AA
R2213 VRD-RA2BE223JY X 22k 1/8W Carbon AA
R2401 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R2402 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R2403 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R2404 VRS-CY1JF101JY X 100 1/16W M-Ox. AA
R2501 VRS-CY1JF123JY X 12k 1/16W M-Ox. AA
R2503 VRS-CY1JF273JY X 27k 1/16W M-Ox. AA
R2504 VRS-CY1JF123JY X 12k 1/16W M-Ox. AA
R2505 VRS-CY1JF563JY X 56k 1/16W M-Ox. AA
R2506 VRS-CY1JF563JY X 56k 1/16W M-Ox. AA
R2507 VRS-CY1JF823JY X 82k 1/16W M-Ox. AA
R2508 VRS-CY1JF153JY X 15k 1/16W M-Ox. AA
R2509 VRS-CY1JF272JY X 2.7k 1/16W M-Ox. AA
R2601 VRD-RA2BE100JY X 10 1/8W Carbon AA
R2603 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R2605 VRS-CY1JF000JY X 00 1/16W M-Ox. AA
R2607 VRS-CY1JF000JY X 00 1/16W M-Ox. AA

FILTERS AND COILS

L50 VP-DF150K0000Y X Peaking 15mH AB
L201 VP-XF1R2K0000Y X Peaking 1.2mH AB
L202 VP-XF1R2K0000Y X Peaking 1.2mH AB
L203 VP-XF220K0000Y X Peaking 22mH AB
L204 RCILI0632CEZZ X IF Coil AB
L301 VP-XF150K0000Y X Peaking 15mH AB

U L701 RCILF0078PEZZ X Coil Line Filter AC

L705 RCILP0179CEZZ+ X Coil AB
L706 RCILP0197CEZZ X Coil AB
L2040 RCILB0131CEZZ X Coil (OSC) AB

TRANSFORMERS

T601 RTRNZ0731CEZZ X TRANSFORMER AD

pU T602 RTRNF0213PEZZ X H-Volt Transformer AP

U T702 RTRNW0003PEZZ X Power Transformer AE

SWITCH

S2501 QSW-K0202PEZZ+ X SWITCH AB
S2502 QSW-K0202PEZZ+ X SWITCH AB
S2503 QSW-K0202PEZZ+ X SWITCH AB
S2504 QSW-K0202PEZZ+ X SWITCH AB
S2505 QSW-K0202PEZZ+ X SWITCH AB

FERRITE BEAD

FB351 RBLN-0047CEZZY X FERRITE BEAD AB
FB601 RBLN-0047CEZZY X FERRITE BEAD AB
FB2002 RBLN-0037CEZZY X FERRITE BEAD AB
JA409 RBLN-0047CEZZY X FERRITE BEAD AB

Ref. No. Part No. « Description Code

JACK

J903 QJAKE0211CE09 X RCA JACK WHITE AB
J905 QJAKE0211CE04 X RCA JACK YELLOW AB

Plug

P302 QPLGN0261CEZZ X Plug (2 ) PINS AB
P401 QPLGN0561CEZZA X Plug 5Pin (KA) AB
P601 QPLGN0660CEZZ X Plug (6 ) PINS AB
P651 QPLGN0361CEZZA X Plug 3pin (TP651-3) AB

P701 QPLGN0260CEZZ X Plug 2pin (M1-2) AB
P751 QPLGN0461CEZZA X Plug 4pin (S1-4) AB
P2001 QPLGN0561CEZZA X Plug 5Pin (KA) AB

MISCELLANEOUS PARTS

RMC2601 RRMCU0222CEZZ X R/C RECEIVER AD
F701 QFS-B4023CEZZ X FUSE 4A 125V AB
FH701 QFSHD1013CEZZ+ X FUSE CLIP AB
FH702 QFSHD1014CEZZ+ X FUSE CLIP AB
RY701 RRLYJ0081CEZZ X RELAY AD
RDA501 PRDAR0297PEFW X Heat Sink (Aluminum) AB
RDA602 PRDAR0216PEFW X Heat Sink (Steel) AB
RDA701 PRDAR0026PEFW X Heat Sink (Steel) AB

PWB-A: DUNTKA359WEW0

CRT Unit

TRANSISTORS

Q852 VSBF422////-1+ X BF422 AB
Q854 VSBF422////-1+ X BF422 AB
Q856 VSBF422////-1+ X BF422 AB
Q881 VS2SA1266-Y-1+ X 2SA1266(Y) AB

DIODES

D882 RH-DX0475CEZZY X Diode AB
D885 RH-DX0475CEZZY X Diode AB

FILTERS

L852 VP-MK820K0000+ X Peaking 82mH AB

CAPACITORS

[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]

C851 VCCCCY1HH151JY X 150p 50V Ceramic AA
C852 VCCCCY1HH151JY X 150p 50V Ceramic AA
C853 VCCSPA1HL151J+ X 150p 50V Ceramic AA
C854 RC-KZ0029CEZZ+ X 0 AC250V Ceramic AB
C883 VCEA0A1CW336M+ X 33 16V EL. AB

RESISTORS

[M-Ox.··· Metal Oxide, M-Film ··· Metal Film]

R852 VRD-RA2BE181JY X 180 1/8W Carbon AA
R853 VRS-CY1JF121JY X 120 1/16W M-Ox. AA
R857 VRS-VV3AB123J X 12K 1W M-Ox. AB
R858 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA
R860 VRD-RA2BE181JY X 180 1/8W Carbon AA
R861 VRS-CY1JF121JY X 120 1/16W M-Ox. AA
R865 VRS-VV3AB123J X 12K 1W M-Ox. AB
R866 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA
R867 VRS-CY1JF470JY X 47 1/16W M-Ox. AA
R868 VRS-CY1JF181JY X 180 1/16W M-Ox. AA
R869 VRS-CY1JF121JY X 120 1/16W M-Ox. AA

R873 VRS-VV3AB123J X 12K 1W M-Ox. AB
R874 VRD-RM2HD332JY X 3.3k 1/2W Carbon AA
R881 VRS-CY1JF561JY X 560 1/16W M-Ox. AA
R882 VRS-CY1JF391JY X 390 1/16W M-Ox. AA
R883 VRD-RA2BE561JY X 560 1/8W Carbon AA
R884 VRS-CY1JF152JY X 1.5k 1/16W M-Ox. AA
R886 VRS-CY1JF821JY X 820 1/16W M-Ox. AA
R887 VRD-RA2BE470JY X 47 1/8W Carbon AA
R890 VRS-CY1JF470JY X 47 1/16W M-Ox. AA
R891 VRS-CY1JF470JY X 47 1/16W M-Ox. AA

MISCELLANEOUS PARTS

SC852 QSOCV0840CEZZ X SOCKET (CRT) AC
P851 QPLGN0561CEZZ X PLUG (5 PINS) AB
P852 QPLGN0461CEZZ X PLUG (4 PINS) AB

21

19C140

Ref. No. Part No. « Description Code

MISCELLANEOUS PARTS

ACC701 QACCDA015WJPZ X AC-CORD AE
SP1 VSP0080PBL4YS X SPEAKER 32ohm 2W AE

QCNW-2111PEZZ X WIRE (YBN) AB
QCNW-2112PEZZ X WIRE (S) AB
QCNW-2160PEZZ X WIRE (GBN) AC
LHLDK0014PEZZ X AC CORD HOLDER AB
LHLDZ0063PEZZ X HOLDER AB
TLABM0002GJZZ X Model label mono voltge UL AB
TLABN0101GJZZ X REMARK LABEL AB
XTASD30P12000 X SCREW (BTN) AA
XTASD40P20000 X SCREW (CAB) AA

SUPPLIED ACCESORRIESSUPPLIED ACCESORRIES

Ref. No. Part No. « Description Code

PACKING PARTS

(NOT REPLACEMENT ITEM)

SPAKCB315WJZZ X PACKING CASE —
SPAKP0102GJZZ X LAMIFOAM AC
SPAKX0003GJZZ X PACKING FOAM AG
SSAKA0101GJZZ X PLASTIC BAG AB

CABINET PARTS

1 CCABA0108WEJ5 X CAB-A ASSY —
1-1 Not Available — FRONT CABINET —

TINS-B244WJZZ X OPERATION MANUAL —
RRMCG1324CESC X R/C GUN AH
TCAUS3000GJZZ X CAUTION LABEL AA
TGAN-A216WJN1 X WARRANTY CARD AB

1-2 GCOVA0003GJSA X COVER —
1-3 HBDGB1001GJSB X BADGE AB
1-4 JBTN-0003GJSJ X Button(Power, —

2 GCABB0109GJKA X REAR CABINET (19RM100) AS

Vol-up/down,CH-up/down)

1-1

1

2

22

1-3

1

-

2

POWER VIDEO IN AUDIO

C

H

–

L

V

+

O

1-4

★ Wrapping Paper

19C140

PACKING OF THE SET

★ Polyethylene Bag

Operation Manual
Infrared R/C Unit

★ Batteries

★ Buffer Material

FRONT

★ MARK : Not replacement items.

★ Packing Case

Use tape to
fix the top side of
packing case.

REAR

Use 10 staples to
fix the bottom side
of packing case.

23

QRC0005-L

Feb. 2004

J B

Design and Production Information

Design base : JAPAN
Production : SEMEX

Modify : SEMEX

COPYRIGHT © 2004 BY SHARP CORPORATION

ALL RIGHTS RESERVED.

No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.

SHARP ELECTRONICA MEXICO S. A. DE C. V.
Quality & Reliability Control Center
Blvd. SHARP No. 3510 Parque Industrial Rosarito
Playas de Rosarito, México B. C. 22710

19C140