SHARP 15JF25, 15JF25F, 15JF25H, 15JF25S, 15JF26H Service manual & schematics

...

Download

Page 1

15JF-25H

SERVICE MANUAL

SE0015JF25H00

Issued: 30th Sept. 2002

GA-1E CHASSIS

PAL I SYSTEM COLOUR TELEVISION

MODEL 15JF-25H

In the interests of user safety (required by safety regulations in some countries) the set should restored to its original condition and only parts identical to those specified should be used.

CONTENTS

ELECTRICAL SPECIFICATION ....................... 3

IMPORTANT SERVICING NOTES .................. 4

CONTROLS & TERMINALS ............................ 5

SERVICE ADJUSTMENTS .............................. 6

CHASSIS LAYOUTS ....................................... 14

LED FLASHING CODES ................................ 15

PRINTED WIRING BOARDS ......................... 15

ICs ADDITIONAL INFORMATION ............. 20

SCHEMATIC DIAGRAMS ............................. 26

BLOCK DIAGRAMS ...................................... 32

TROUBLESHOOTING TABLES .................... 34

PARTS LISTING ........................................... 37

ACCESSORIES ............................................... 42

SOURCE OF DOCUMENTATION ................ 42

SHARP CORPORATION

This document has been published to be used for after sales service only.

Page 2

15JF-25H

SERVICE MANUAL UPDATE LOG SHEET

Technical Report No. Technical Bulletin No.

Cause / Solution

Part No.

Page No.

Application Data /Serial No.

Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section. If you need more information, please refer to the Technical Report (Bulletin).

Page 3

ELECTRICAL SPECIFICATIONS

15JF-25H

•Power Input .................... 220V-240 Volts AC 50Hz

•Power Consumption

Normal Operation (Method IEC60107) ............ 37W

Stand-by Operation ............................................ 3W

•Audio Power Output Rating ........................ 2 W (MPO)

Speaker .............................. 16Ω, 4W, 9 x 5 cm, 1pc

•Convergence ............................... Self Converging System

•Focus ....................... High Bi-Potential Electrostatic

•Sweep Deflection ..................................... Magnetic

•Picture Intermediate frequency ................. 38.9 MHz

•Sound Carrier Trap .................................. 32.9 MHz

•Adjacent Sound Carrier Trap ................... 40.9 MHz

•Adjacent Picture Carrier Trap ................. 30.9 MHz

•Aerial Input Impedance

VHF/UHF ...................... 75 ohm Unbalanced

•Tuning Ranges........... 45.75 MHz thru 855.25 MHz

VHF.................... IR A-J

VHF .................. S1 - S41 (HYPERBAND)

UHF .................. I21 - I69 CH

•White Level Set brightness control to get total picture tube cathode current of 900 µA under no signal condition. Maximum necessary correction of each picture tube cathode current to get 8900 degrees K-20 MPCD screen temperature should not exceed 15% of its original value.

X=0.290 ± 0.015 Y=0.284 ± 0.015

Specifications are subject to change without prior notice.

WARNING

The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service personnel.

Page 4

15JF-25H

IMPORTANT SERVICING NOTES

Only qualified service personnel are allowed to carry out maintenance and repair of this receiver.

Servicing of High Voltage System and CRT

It is important that the static charge is removed from the high voltage system when carrying out work on the receiver. This can be achieved by connecting a 10K resistor (with a suitably insulated lead) from the CRT cavity connector to the CRT ground tag. This must be carried out with the AC supply disconnected from the receiver.

Note the following:

• The CRT in this receiver employs Integral Implosion Protection.

• If the CRT has to be changed it MUST be replaced with the correct type for continued safe working.

• DO NOT lift the CRT by its neck.

• When handing the CRT, ensure that shatterproof goggles are worn.

• Ensure that the CRT is discharge before handling.

X-Ray

This receiver is designed to keep any x-ray emission to an absolute minimum. Some fault conditions and servicing procedures may produce potentially hazardous x-ray radiation levels. This is a problem when in close proximity to the receiver for long periods of time. To reduce any risks associated with this, please observe the following precautions:

1. When undertaking any servicing on this chassis, DO NOT increase the EHT to more than 27.5 KV, (at a

instantaneous beam current of 1000µA).

2. Ensure that during normal operation the EHT does not exceed 24.5 KV±1.5KV (at a beam current of 900µA). This level has been preset in the factory. Always check that this level has not been exceeded after carrying out any repair on the receiver.

3. DO NOT replace the CRT with any other type than that specified in the parts listing as this may cause excessive x-ray radiation.

Before returning the receiver to the customer

In addition to the above checks, the following should also be carried out before returning the receiver to the customer.

1. Inspect all the leads to ensure that they are dressed correctly and that they are not obstructed or pinched by any other parts.

2. Ensure that all protective devices are in good condition. These will include nonmetallic control knobs, insulating fish papers, cabinets backs, compartment covers or shields, mechanical insulators, etc.

Page 5

Remote Control

CONTROLS & TERMINALS

CALL ( )/CHILD LOCK ( ) button

15JF-25H

Infrared Transmitter Window

Aim this window at the infrared sensor on your TV set

TV Front

SOUND MUTE ( ) button

POWER/STANDBY ( ) button

Programme Select buttons

FLASHBACK ( ) button

Returns to previously viewed programme

VOLUME UP ( )/DOWN ( ) button

( ) Increases sound ( ) Decreases sound (These are also used for menu set up)

CLOCK ( ) button (Teletext)

REVEAL ( ) button (Teletext)

HALF PAGE ( ) button (Teletext)

CANCEL ( ) button (Teletext)

RESET ( ) button (Teletext)

TV/VIDEO

1 2 3

4 5 6

7 8 9

XiS

TV/TEXT REMOTE CONTROL

LIST

TV/VIDEO Select button

Single/Double Entry button ( )

CHANNEL (PROGRAMME) UP ( )/

DOWN ( ) button

( ) Selects next higher programme ( ) Selects next lower programme (These are also used for menu set up)

Text/Mix/Picture ( ) Select button (Teletext)

COLOUR buttons

INDEX ( ) button (Teletext)

HOLD ( ) button (Teletext)

LIST Select button (Teletext)

STORE ( ) button (Teletext)

Power ( ) button

Power/On Timer indicator

Remote Control Sensor

Volume Up ( )/Down ( ) buttons

Channel Up ( )/Down ( ) buttons

Menu button

Euro-SCART, 21 Pin Terminal

For greater A/V enjoyment, various audio and video devices may be connected via the Euro-SCART 21-Pin Terminal.

1. Audio right output

2. Audio right input

3. Audio left output

4. Common earth for audio

5. Earth for blue

6. Audio left input

7. Blue input

8. Audio-video control

9. Earth for green

10. Not used

11. Green input

12. Not used

13. Earth for red

14. Not used

15. Red input

16. Red/Green/Blue

17. Earth for video

Audio: Mono Input/Output.

control

Earphone Jack

3.5 mm ø Jack PLUG Earphone impedance 16 ~ 600 ohm

21-Pin Euro-

18. Earth for video

19. VIDEO output

20. VIDEO input

21. Common earth

Page 6

15JF-25H

SERVICE ADJUSTMENTS

•Service Mode Function

All required adjustments for servicing this TV set, may be done in “Service Mode”, excepting G2 and FOCUS.

How to access the Service Mode

1. Turn the receiver on and ensure that it is tuned into a test pattern.

2. Turn the receiver off using the mains switch.

3. Press the volume down and channel up buttons together. See Figure 1.

4. Continue pressing the volume down and channel up buttons while turning the mains on using the mains switch. See Figure 1.

5. Keep pressing the volume down and channel up buttons until the picture appears.

6. When <<SHARPX X VXX.XX>> appears on the screen, release the two buttons.

7. The receiver is now in the Service Mode. See Figure 2.

To move between the various Service Mode functions, use the channel up and down buttons. See Figure 3.

Use the volume buttons to change the data to the desired value. See Figure 3.

The data will be stored automatically when exiting the Service Mode. To exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch.

Figure 1

SHARP X X VXX.XX

STS0: XXXX XXXX STS1: XXXX XXXX STS2: XXXX XXXX

Figure 2

Adjustment (Yellow)

XXXX:

Figure 3

XX:

Value (Green)

•How to record a new (blank) NVM (EEP-ROM)

When the NVM (EEP-ROM) is replaced for a new one, the Microprocessor automatically record values shown in “Initial” column (Page 7).

Procedure:

1. Access the Service Mode. See the above procedure “How to access the Service Mode”. Now the Microprocessor has recorded the “Initial” Values.

Page 7

15JF-25H

2. Change manually the value of those NVM position pointed out in grey shadow from the “Initial” Value to “Default” Value (Page 7) .

3. Adjust the TV set as detailed in the following pages ( Screen, AGC, Geometry and Colour Adjustments).

• Service Adjustments and Data List

The table below shows the various Service Mode positions, range of values and default value. The columns are headed as follows.

Heading: Description:

OSD This is what will appear on the screen when at this position

Function This is the description of the mode’s function

Range This is the range of values that can be entered while in this mode

Initial This is the value recorded just after changing the NVM

Default This is the recommended default value for this mode

FIX/ADJ If this is ADJ, then it may be necessary to adjust this value away from the default

No. OSD Function Range Initial Default FIX/ADJ

1 AGC AGC Take Over Point 0...63 14 34 ADJ

2 V-LIN Vertical Slope [VS] 0...63 32 33 ADJ

3 V-AMP Vertical Amplitude [VA] 0...63 32 27 ADJ

4 V-CENT Vertical Shift [VSH] 0...63 32 32 ADJ

5 H-CENT Horizontal shift [HS] 0...63 32 24 ADJ

6 H-CENT60 offset to H-CENT for 60 Hz 0...31 data (-16..+15) 16 20 FIX

7 EW / / Horizontal Parallelogram [HP] 0...63 32 32 FIX

8 HB Horizontal Bow 0...63 32 32 FIX

9 S-COR S-Correction [SC] 0...63 0 22 FIX

10 DRI-RS White point Red Standard white temp. 0...63 32 42 ADJ

11 DRI-GS White point Green Standard white temp. 0...63 32 42 ADJ

12 DRI-BS White point Blue Standard white temp 0...63 32 42 ADJ

13 DRI-RW White point Red Warm white temp. 0...32 16 16 FIX

14 DRI-GW White point Green Warm white temp. 0...32 16 9 FIX

15 DRI-BW White point Blue Warm white temp. 0...32 16 9 FIX

16 DRI-RC White point Red Cold white temp. 0...32 16 9 FIX

17 DRI-GC White point Green Cold white temp. 0...32 16 9 FIX

18 DRI-BC White point Blue Cold white temp. 0...32 16 16 FIX

19 SUB-VOL Max Volume 0...63 60 52 FIX

20 SUB-CON Sub Contrast 0...63 63 63 FIX

21 SUB-COL Sub Colour 0...63 32 25 FIX

22 SUB-BRI Sub Brightness 0...63 32 33 FIX

23 TINT Sub Tint 0...63 32 32 FIX

24 SUB-SHP Sub Sharpness 0...63 32 11 FIX

Page 8

15JF-25H

No. OSD Function Range Initial Default FIX/ADJ

25 HTL-VOL Max Hotel Volume 0...63 30 30 FIX 26 HTL-PRG Hotel Program number 0...99 or > 99 for none 255 255 FIX 27 RGB OSD RGB Reference 0...15 15 0 FIX 28 SEARCH-SYS Sound system for auto turning 0(L-BG),1(BG),2(I),3(DK) 1 2 FIX 29 CUT-R Black Level off-set R [BLR] 0...63 0 0 FIX 30 CUT-G Black Level off-set G [BLG] 0...63 0 10 FIX 31 CDL Cathode Drive Level [CL] 0...15 0 3 FIX 32 DL-PT Y-Delay time for PAL (TV) [YD] 0...15 12 4 FIX 33 DL-ST Y-Delay time for SECAM (TV) [YD] 0...15 15 8 FIX 34 DL-4T Y-Delay time for N443 (TV) [YD] 0...15 12 8 FIX 35 COL-OP COLOUR OFFSET (PAL) 0...15 8 8 FIX 36 COL-OS COLOUR OFFSET (SECAM) 0...15 8 8 FIX 37 COL-O4 COLOUR OFFSET (NTSC443) 0...15 4 4 FIX 38 SHP-OP SHARPNESS OFFSET(PAL) 0...15 8 8 FIX 39 SHP-OS SHARPNESS OFFSET(SECAM) 0...15 4 4 FIX 40 SHP-O4 SHARPNESS OFFSET(NTSC443) 0...15 8 8 FIX 41 SC-VOL SCART volume 0..255 115 115 FIX 42 PRE-SC Prescaler SCART input 0..127 25 25 FIX 43 PRE-FM Prescaler FM/AM 0..127 72 72 FIX 44 PRE-NICAM Prescaler SCART input 0..127 0 0 FIX 45 AVC-DKY AVC Decay 0...3 data(1.2.4.8.) 2 2 FIX 46 AC-OFF-TIM Time to set the AC-OFF 0..15 0 0 FIX

timer is in steps of 10 minutes

47 DISP Language or symbols 0(symboles), 0 1 FIX

1(English), 2(French)

48 TXT-EUR Teletext pan-European language 0 (teletext pan-European language) 0 0 FIX

1 (second language;cyrillic)

2 (third language;Greek) 49 BKS Black Stretch 0 (disable) or 1 (enable) 1 1 FIX 50 AVC Automatic Volume Control(AVL) 0 (disable) or 1 (enable) 0 1 FIX 51 FFI Fast Filter IF-PLL 0 (disable) or 1 (enable) 0 0 FIX 52 ACL Auto Colour Limit 0 (disable) or 1 (enable) 0 1 FIX 53 S-L Sound system L 0 (disable) or 1 (enable) 0 0 FIX 54 S-DK Sound system DK 0 (disable) or 1 (enable) 1 0 FIX 55 S-I Sound system I 0 (disable) or 1 (enable) 1 1 FIX 56 S-BG Sound system BG 0 (disable) or 1 (enable) 1 0 FIX 57 BLUE-BACK Video mute at Ident loss 0 (disable) or 1 (enable) 1 1 FIX 58 VMC V ideo Mute at program/source Change 0 (disable) or 1 (enable) 1 0 FIX 59 HTL Hotel mode 0 (disable) or 1 (enable) 0 0 FIX 60 BTSC Reduced FM demodulator Gain (for BTSC sig) 0 (disable) or 1 (enable) 0 0 FIX 61 AV Number of external AV sources 0 for 1 AV or 1 for 2 AV 1 0 FIX 62 FMWS FM Window Selection 0 (disable) or 1 (enable) 0 0 FIX 63 SM0 Sound Mute bit 0 0 (disable) or 1 (enable) 1 1 FIX 64 SM1 Sound Mute bit 1 0 (disable) or 1 (enable) 0 0 FIX 65 AGC0 IF AGC speed bit0 0 (disable) or 1 (enable) 1 1 FIX 66 AGC1 IF AGC speed bit1 0 (disable) or 1 (enable) 0 0 FIX 67 FOA-FE Phi 1 time constant for FE(RF) 0 (disable) or 1 (enable) 0 0 FIX 68 FOB-FE Phi 2 time constant for FE(RF) 0 (disable) or 1 (enable) 0 0 FIX 69 FOA-AV Phi 1 time constant for AV 0 (disable) or 1 (enable) 1 1 FIX 70 FOB-AV Phi 2 time constant for AV 0 (disable) or 1 (enable) 1 1 FIX 71 TXT Teletext 0 (disable) or 1 (enable) 0 1 FIX 72 TXT-WE Teletext Western or Eastern characters 0 (western) or 1 (eastern) 0 0 FIX 73 FSL Forced V-SYNC slicing level 0 (disable) or 1 (enable) 0 0 FIX 74 HP2 Sync of OSD 0 for Ph1 or 1 for Ph2 0 0 FIX 75 CP Charge pump 0 (fast tuning) or 0 0 FIX

1 (moderate speed tuning) 76 NICAM NICAM decoding enabled 0 (disable) or 1 (enable) 0 0 FIX 77 IGR IGR decoding enabled 0 (disable) or 1 (enable) 0 0 FIX 78 AUTO Start auto tuning at POWER-ON 0 (disable) or 1 (enable) 0 0 FIX 79 TXT-TGL Function of TXT key 0 or 1 0 1 FIX 80 EVG Enable Vertical Guard 0 (disable) or 1 (enable) 1 1 FIX

Page 9







• Screen Adjustment

1. G2 Adjustment

1. Enter the Service Mode (see page 6).

2. Use the channel up or channel down buttons to enter the << BLUE-BACK >> function.

3. Set this to << BLUE-BACK: 0 >>, i.e. blue background is turned off.

4. Turn the set off at the mains.

5. Turn the set back on.

6. Set the picture control settings to normal.

7. Select the SCART input by pressing the TV/SCART button on the remote control. Do not connect an input to the SCART socket. A blank raster will appear.

8. Connect an oscilloscope to TP852 on the CRT PWB. The waveform as in figure 4 should be displayed.

9. Adjust the G2 control (screen voltage) so that the peak of this waveform is 3.0V +/-0.1V above the zero volt line.

15JF-25H

Figure 4

10. Enter the Service Mode.

11. Turn the blue background function back on again - set << BLUUE-BACK: 1 >>.

12. Turn off the receiver using the mains button.

13. The G2 adjustment is now complete.

2. Focus Adjustment

1. Receive a monoscope pattern signal at a level of 60 to 80 dB/µV.

2. Set the picture settings to normal.

3. Adjust the focus potentiometer to obtain maximum definition.

• AGC Adjustment

1. Tune the receiver into a colour bar signal on channel I-42.

2. Set the RF generator to an output signal strength of 57dB/µV (+/-1dBµV) –50 Ohms unbalanced.

3. Connect an oscilloscope to TP201. TP201 is one end of R201.

4. Enter the Service Mode (see page 6).

5. Use the channel up and channel down buttons to enter the AGC mode.

6. By using the volume up and the volume down buttons, adjust the AGC until the voltage on TP201 drops by 0.1V

7. Change the input signal strength to 66-70 dB/µV and make sure that there is no noise apparent in the picture.

8. Turn the receiver off at the mains, this will exit the Service Mode and store the adjustment.

to 0.3V below its maximum value.

Page 10

15JF-25H

• Geometry Adjustment Procedure

To adjust the geometry, follow the procedure outlined below:

1. Tune the set into a Philips test pattern.

2. Enter the Service Mode as described on page 6.

3. Use the channel up or channel down buttons to enter the desired mode

4. Use the volume buttons to achieve correct setting.

5. When adjustments are complete, use the stand-by button to turn off the set. The adjustment values will be stored at this point.

V-LIN

Adjust the vertical linearity control so that the picture centring is as shown in figure 5.

V-AMP

Adjust the vertical amplitude control so that the picture overscans as shown in figure 6.

V-CENT

Adjust the vertical centring control so that the picture is centred as shown in figure 7.

H-CENT

Adjust the horizontal centring control so that the picture is centred as shown in figure 8.

Figure 5

Figure 6

Figure 7

Figure 8

Page 11

15JF-25H

•Colour Adjustment Procedure

The following adjustments should only be carried out when the CRT or IC801 are replaced.

Notes:

• This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 700

µA.

• The red value «DRI-RS» should be fixed to 42. (Refer to “How to access Service Mode” section).

• «DRI-GS» adjustment alters “Y” co-ordinate.

• «DRI-BS» adjustment alters “X” and “Y” co-ordinates.

Adjustment Method 1 (using the signal generator, varying the picture signal)

1. Adjust G2.

2. Input a white pattern with burst signal from SCART.

3. Position the colorimeter in the centre of screen.

4. Adjusting input signal level, select a luminance of 70 nits.

5. Operate again in “Service Mode“ and select «DRI-GS» and/or «DRI-BS» locations to obtain colour co-ordinates:

X Y Screen temperature

0.290 ± 0.015 0.284 ± 0.015 8900º K-20 MPCD

6. Re-set the TV with the mains switch button to store the adjustment and exit Service Mode.

7. Check colour co-ordinates “X” and “Y” at 20 a 120 Nits. It may be necessary to repeat the same procedure to obtain the above values.

Adjustment Method 2 (using the signal generator, with a fixed picture signal)

1. Adjust G2.

2. Tune a white pattern with burst signal.

3. Operate in “Service Mode”:

4. Using «SUB-CON», select a luminance of 70 nits.

5. Operate again in “Service Mode“ and select «DRI-GS» and/or «DRI-BS» locations to obtain colour co-ordinates:

X Y Screen temperature

0.290 ± 0.015 0.284 ± 0.015 8900º K-20 MPCD

6. Select «SUB-CON». Return data to “63”.

7. Re-set the TV with the mains switch button to store the adjustment and exit Service Mode.

8. Check colour co-ordinates “X” and “Y” at 20 a 120 Nits. It may be necessary to repeat the same procedure to obtain the above values.

Page 12

15JF-25H

•Hotel Mode Functions

The following procedure details how to set up the Hotel Mode Functions.

1. Short Description

1.1. Hotel Mode “HTL”: Main Hotel Mode. It deactivates “Channel Setting” functions. It reduces the Maximum Volume.

1.2. Hotel Mode “HTL-VOL”: Maximum Volume Level Regulation.

1.3 Hotel Mode “HTL-PRG”: Fixing start up program when the TV set is switched on.

2. Before start

2.1. It is necessary to program “Channel Setting” before setting up Hotel Mode “HTL” because after that Channel Setting are deactivated.

2.2. Consider that regarding TXT Features, after activate any of the Hotel modes in the “List Mode” will not be stored any page.

2.3. Consider that changed video control values are not stored.

3. Procedure

3.1. Hotel Mode “HTL” (Main Hotel Mode).

3.1.1. Previous Service Information: Initial Value: 0. Range: 0 to 1. Service Mode Indication: HTL.

3.1.2. Access the Service Mode (see this procedure on page 6).

3.1.3. Select “HTL” by using channel up/down buttons.

3.1.4. Change initial value from “0” (off ) to “1” (on).

3.1.5. Notes:

3.1.5.1. The maximum volume level has been reduced from 60 to 30. For other value go to 3.2. Hotel Mode

“HTL-VOL”

3.1.5.2. “Channel Setting” functions have been deactivated.

3.1.5.3. It is necessary to select Hotel Mode “HTL” to be able to set up Hotel Mode “HTL-VOL” or Hotel Mode “HTL-PRG”.

3.1.5.4. If you do not need to set up Hotel Mode “HTL-VOL” or “HTL-PRG” get out from Service Mode (To

exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).

3.2. Hotel Mode “HTL-VOL” (Maximum Volume Level Regulation)

3.2.1. Previous Service Information: Initial value: 30. Range: 0 to 60. Service Mode indication: HTL-VOL.

3.2.2. To activate this Hotel Mode it is necessary activate previously Hotel Mode “HTL”. Then the maximum volume level changed fro 60 to 30 as initial value.

Page 13

15JF-25H

3.2.3. Select “HTL-VOL” by using channel up/down buttons.

3.2.4. Set the value according to your necessities by using volume up/down buttons.

3.2.5. Change initial value from “0” (off ) to “1” (on).

3.2.6. Note: If you do not need to set up Hotel Mode “HTL-PRG” get out from Service Mode (To exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).

3.3. Hotel Mode “HTL-PRG” (Fixing start up program when the TV Set is switched on)

3.3.1. Initial value: 255. Range: 0 to 255. Service Mode indication: HTL-PRG.

3.3.2. To activate this Hotel Mode it is necessary activate previously Hotel Mode “HTL”.

3.3.4. Select “HTL-PRG” by using channel up/down buttons.

3.3.3. The initial value to 255, ensures that the TV Set starts up in the same program number that it was been displayed before turn it off.

3.3.4 If you want to fix other program number proceed as follows set the value according to your necessities by using volume up / down buttons. Use values between 0 to 99. In this way, the new program number appear fixed when you start up the TV set.

Example: If you would like to set starting program number “2”, change from 255 to 2.

3.3.5. Get out from Service Mode (To exit the Service Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).

Page 14

15JF-25H

Mother Unit

CHASSIS LAYOUTS

CRT Unit

Page 15

LED FLASHING CODES

PURPOSE: The led indicates the power mode,ocurred I2C error and On timer

INPUT: - Current power mode

- I2C Errors

- On timer

Processing: - If in STAND-BY mode and On timer in-active then switch LED off.

- If in STAND-BY and On timer active set LED to blinking, (switch on and off at 1 Hz with a 50 % duty cycle).

- If in POWER-ON mode, switch LED on.

- If an I2C error occurred, let the LED blink at 1 Hz, 50 % duty cycle. For the blinking times see the Table below.

Note: Only when an I2C error occurs for a number of times, or for a number of seconds,

the I2C error is handled by the system (that is ,only then the set will go to stand-by, the led starts blinking).

15JF-25H

IC/Module Name Slave Address Bus Error LED Remarks Ref. No.

Blinking Time

M24C04 or M24C08 A0,A2 2 512x8 EEPROM or 1024x8 EEPROM IC1002 TDA935x/6x/8x 8A 3 Address of internal TV processor IC801 VTST6HD64 or C0 6 PLL Tuner TU201 CTF551 C0 6

Table Error LED blinking times

PRINTED WIRING BOARDS

F 7341N0 PWB. Components side.

56 78

101

Page 16

15JF-25H

F7340N6 PWB. Component side

19 18 17 16 15 14 13 1225 24 23 22 21 20

Page 17

15JF-25H

F7340N6 PWB. Component side

Page 16

76 543 2113 12 11

Page 18

15JF-25H

F7340N6 PWB. Copper side

19 18 17 16 15 14 13 1225 24 23 22 21 20

Page 19

15JF-25H

F7340N6 PWB. Copper side

Page 18

76 543 2113 12 11

Page 20

15JF-25H

SYMBOL PARAMETER MIN. TYP. MAX. UNIT

Supply

supply voltages − 8.0/3.3 − V

supply current − 135/60 − mA

Input voltages

iVIFrms)

video IF ampliﬁer sensitivity (RMS value) − 75 −µV

iSIF(rms)

QSS sound IF ampliﬁer sensitivity (RMS value) − 60 −µV

iAUDIO(rms)

external audio input (RMS value) − 500 − mV

iCVBS(p-p)

external CVBS/Y input (peak-to-peak value) − 1.0 − V

iCHROMA(p-p)

external chroma input voltage (burst amplitude) (peak-to-peak value)

− 0.3 − V

iRGB(p-p)

RGB inputs (peak-to-peak value) − 0.7 − V

iYIN(p-p)

luminance input signal (peak-to-peak value) − 1.4 − V

iUVIN(p-p)

U/V input signal (peak-to-peak value) − 1.33/1.05 − V

Output signals

o(IFVO)(p-p)

demodulated CVBS output (peak-to-peak value) − 2.5 − V

o(QSSO)(rms)

sound IF intercarrier output in QSS versions (RMS value) − 100 − mV

o(AMOUT)(rms)

demodulated AM sound output in QSS versions (RMS value)

− 500 − mV

o(AGCOUT)

tuner AGC output current range 0 − 5mA

oRGB(p-p)

RGB output signal amplitudes (peak-to-peak value) − 2.0 − V

oHOUT

horizontal output current 10 −−mA

oVERT

vertical output current (peak-to-peak value) 1 −−mA

oEWD

EW drive output current 1.2 −−mA

TDA93XX (IC801)

Quick Reference Data

ICs ADDITIONAL INFORMATION

Pinning

AVL/SNDIF/

REFO/AMOUT

DECSDEM/SIFIN2

GND2

SNDPLL/SIFAGC

VSC

TUNERAGC

AUDEEM/SIFIN1

IREF

IFIN2

IFIN1

VDRB

VDRA

AVL/EWD

GND3

DECBG

PH1LF

PH2LF

VP2

DECDIG

VSSA

SECPLL

P0.6

P0.5

VSSC/P

P3.3/ADC3/PWM3

P3.0/ADC0/PWM0

P3.1/ADC1/PWM1

P3.2/ADC2/PWM2

P1.6/SCL

P1.7/SDA

P2.0/TPMW

Fig. 3 Pin configuration (SDIP 64)

MXXxxx

FBISO

HOUT

AMOUT

AUDEXT/QSSO/

EHTO

PLLIF

IFVO/SVO

VP1

CVBSINT

GND1

CVBS/Y

INSSW2

CHROMA

AUDOUT/AMOUT

TDA935X/6X/8X PS/N2

R2/VIN

G2/YIN

XXX

BCLIN

B2/UIN

BLKINBOGO

VDDA

VPE

VDDC

OSCGND

XTALIN

XTALOUT

RESET

VDDP

P1.0/INT1

P1.1/T0

P1.3/T1

P1.2/INT0

handbook, halfpage

Page 21

SYMBOL PIN DESCRIPTION

P1.3/T1 1 port 1.3 or Counter/Timer 1 input P1.6/SCL 2 port 1.6 or I

C-bus clock line

P1.7/SDA 3 port 1.7 or I

C-bus data line P2.0/TPWM 4 port 2.0 or Tuning PWM output P3.0/ADC0/PWM0 5 port 3.0 or ADC0 input or PWM0 output P3.1/ADC1/PWM1 6 port 3.1 or ADC1 input or PWM1 output P3.2/ADC2/PWM2 7 port 3.2 or ADC2 input or PWM2 output P3.3/ADC3/PWM3 8 port 3.3 or ADC3 input or PWM3 output VSSC/P 9 digital ground for µ-Controller core and periphery P0.5 10 port 0.5 (8 mA current sinking capability for direct drive of LEDs) P0.6 11 port 0.6 (8 mA current sinking capability for direct drive of LEDs) VSSA 12 analog ground of Teletext decoder and digital ground of TV-processor SECPLL 13 SECAM PLL decoupling VP2 14 2

supply voltage TV-processor (+8V) DECDIG 15 decoupling digital supply of TV-processor PH2LF 16 phase-2 ﬁlter PH1LF 17 phase-1 ﬁlter GND3 18 ground 3 for TV-processor DECBG 19 bandgap decoupling AVL/EWD

(1)

20 Automatic Volume Levelling /East-West drive output VDRB 21 vertical drive B output VDRA 22 vertical drive A output IFIN1 23 IF input 1 IFIN2 24 IF input 2 IREF 25 reference current input VSC 26 vertical sawtooth capacitor TUNERAGC 27 tuner AGC output AUDEEM/SIFIN1

(1)

28 audio deemphasis or SIF input 1 DECSDEM/SIFIN2

(1)

29 decoupling sound demodulator or SIF input 2 GND2 30 ground 2 for TV processor SNDPLL/SIFAGC

(1)

31 narrow band PLL ﬁlter /AGC sound IF AVL/SNDIF/REF0/

AMOUT

(1)

32 Automatic VolumeLevelling/ sound IFinput / subcarrier referenceoutput /AM output

(non controlled) HOUT 33 horizontal output FBISO 34 ﬂyback input/sandcastle output AUDEXT/

QSSO/AMOUT

(1)

35 external audio input /QSS intercarrier out /AM audio output (non controlled)

EHTO 36 EHT/overvoltage protection input PLLIF 37 IF-PLL loop ﬁlter IFVO/SVO 38 IF video output / selected CVBS output VP1 39 main supply voltage TV-processor (+8 V) CVBSINT 40 internal CVBS input GND1 41 ground 1 for TV-processor CVBS/Y 42 external CVBS/Y input CHROMA 43 chrominance input (SVHS) AUDOUT /AMOUT

(1)

44 audio output /AM audio output (volume controlled)

TDA93XX (IC801)

Pinning

15JF-25H

Page 22

15JF-25H

TDA93XX (IC801)

Pinning

SYMBOL PIN DESCRIPTION

INSSW2 45 2 R2/VIN 46 2 G2/YIN 47 2 B2/UIN 48 2 BCLIN 49 beam current limiter input / (V-guard input, note 2) BLKIN 50 black current input / (V-guard input, note 2) RO 51 Red output GO 52 Green output BO 53 Blue output VDDA 54 analog supply of Teletext decoder and digital supply of TV-processor (3.3 V) VPE 55 OTP Programming Voltage VDDC 56 digital supply to core (3.3 V) OSCGND 57 oscillator ground supply XTALIN 58 crystal oscillator input XTALOUT 59 crystal oscillator output RESET 60 reset VDDP 61 digital supply to periphery (+3.3 V) P1.0/INT1 62 port 1.0 or external interrupt 1 input P1.1/T0 63 port 1.1 or Counter/Timer 0 input P1.2/INT0 64 port 1.2 or external interrupt 0 input

RGB / YUV insertion input

R input / V (R-Y) input

G input / Y input

B input / U (B-Y) input

Note

1. The function of pin 20, 28, 29, 31, 32, 35 and 44 is dependent on the IC version (mono intercarrier FM demodulator / QSS IF amplifier and East-West output or not) and on some software control bits. The valid combinations are given in table 1.

2. The vertical guard function can be controlled via pin 49 or pin 50. The selection is made by means of the IVG bit in subaddress 2BH.

Table 1 Pin functions for various versions

IC version FM-PLL version QSS version

East-West Y/N N Y N Y CMB1/CMB0 bits 00 01/10/11 00 01/10/11 00 01/10/11 00 01/10/11 AM bit −− − − −01 − 01 Pin 20 AVL EWD AVL EWD Pin 28 AUDEEM SIFIN1 Pin 29 DECSDEM SIFIN2 Pin 31 SNDPLL SIFAGC Pin 32 SNDIF

(1)

REFO

(2)

AVL/SNDIF

(1)

REFO

(2)

AMOUT REFO

(2)

AMOUT REFO

(2)

Pin 35 AUDEXT AUDEXT QSSO AMOUT AUDEXT QSSO AMOUT Pin 44 AUDOUT controlled AM or audio out

Note

1. When additional (external) selectivity is required for FM-PLL system pin 32 can be used as sound IF input. This function is selected by means of SIF bit in subaddress 28H.

2. The reference output signal is only available for the CMB1/CMB0 setting of 0/1. For the other settings this pin is a switch output (see also table 67).

Page 23

TDA93XX (IC801)

Block Diagram

15JF-25H

+3.3 V

I/O PORTS (4x)

ADC IN (4x) VST OUT

SDASCL

LED OUT (2x)

VPE

RESET

AUDOUT

AUDEXT

54 56

1+62-64

5-8

C-BUS

10/11

60 55 59 58 57

1/10 PAGE

MEMORY

I/O PORTS

TRANSCEIVER

VST PWM-DAC

80C51 CPU

ENHANCED

DISPLAY

TELETEXT/OSD

TELETEXT

ACQUISITION

CVBS

ROM/RAM

ROGOB0

515253

BL B

CONTR/BRIGHTN

OSD/TEXT INSERT

COR

SYNC

PEAKING

LUMA DELAY

BLKIN

BCLIN

CCC

BLACK STRETCH

WHITE-P. ADJ.

RGB/YUV INSERT

45 484746

SATURATION

RGB/YUV MATRIX

YUV/RGB MATRIX

(20)

(EW GEOMETRY)

222625

V-DRIVE +

GEOMETRY

G/Y B/U BL R/V

EWD

EHTO

HOUT V-DRIVE

TRAP

SOUND

SNDIF

TUNERAGC

29 28

(20)

(32)

27 37 38

(32)

(AVL)

DEEMPHASIS

AUDIO SWITCH

VOLUME CONTROL

AGC/AFC

VISION IF

VIDEO AMP.

PLL DEMOD.

ALIGNMENT-FREE

IFIN

PLL

AGC CIRCUIT

NARROW BAND

DEMODULATOR

VIDEO IDENT.

VIDEO SWITCH

VIDEO FILTERS

CHROMA

CVBS/Y

BASE-BAND

REF

PAL/SECAM/NTSC

DELAY LINE

DECODER

(32)

LOOP

H-DRIVE

H/V SYNC SEP.

+8V

H-SHIFT

H-OSC. + PLL

Block diagram TDA935X/6X8X PS/N2 with mono intercarrier sound demodulator

Page 24

15JF-25H

SUPPLY

MANAGEMENT

internal

supply

UVLO start

M-level

GND

CTRL

FREQUENCY

CONTROL

VOLTAGE

CONTROLLED

OSCILLATOR

LOGIC

OVER-

VOLTAGE

PROTECTION

OVERPOWER PROTECTION

short

winding

soft

start

OVER-

TEMPERATURE

PROTECTION

UVLO

MAXIMUM

ON-TIME

PROTECTION

POWER-ON

RESET

−

VALLEY

TEA1507

100 mV

clamp

DRIVER

START-UP

CURRENT SOURCE

0.75 V

0.5 V

sense

DRIVER

DEM

DRAIN

HVS n.c.

OCP

LEB

blank

2.5 V

burst detect

TEA1507 (IC701)

Block Diagram

SYMBOL PIN DESCRIPTION

GND 2 ground

1 supply voltage

CTRL 3 control input DEM 4 input from auxiliary winding for

sense

demagnetization timing, OVP and OPP

5 programmable current sense input DRIVER 6 gate driver output HVS 7 high voltage safety spacer, not

connected

DRAIN 8 drain of external MOS switch, input for

start-up current and valley sensing

handbook, halfpage

GND

CTRL

DEM

3 4

TEA1507

Pin configuration.

MGU231

8 7 6 5

DRAIN HVS DRIVER I

sense

Page 25

AN7523 (IC303)

Block Diagram Pin Descriptions

Note: Do not apply voltage or current to NC pin from outside

Output

GND

Output

Standby

Input

GND

N.C.

Volume

15JF-25H

Pin No. Description

1 Vcc

2 Ch Output (+)

3 GND

4 Ch Output (-)

5 Stand-by

6 Ch Input

7 GND (Input)

8 N.C

9 Volume

AN5522 (IC501)

Block Diagram Pin Descriptions

Pin No. Pin Name

1 Inverting Input

2 Power Supply

3 Pump-up Output

4 GND

5 Vertical Output

6 Vertical Output Power Supply

7 Non-inverting Input

Pump Up

12 3

Vcc

Inverting Input

Pump Up Out

Thermal Protection

Amp

GND

567

Output

Output Vcc

Non-inverting Input

Page 26

15JF-25H

Description

SAFETY NOTE:

1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS.

2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING.

IMPOTANT SAFETY NOTE:

PARTS MARKED WITH « » ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.

CAUTION This circuit diagram is original one, therefore there may be slight difference from yours.

SCHEMATIC DIAGRAMS

NOTE:

1. The unit of resistance «ohm»is omitted (K=1000 ohms. M= Megaohm).

2. All resistors are 1/16 watt. unless otherwise noted.

3. All capacitors are

µµF).

4. The capacitor with Part No. RC-FZ9XXXBMNJ is designed to with stand 63V.

5. The capacitor with Part No. RC-FZ4XXXBMNJ is designed to with stand 50V.

SERVICE PRECAUTION:

THE AREA ENCLOSED BY THIS LINE ( ) IS DIRECTLY CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK.

WAVEFORM MEASUREMENT CONDITION:

Colour bar generator signal of 70 dB from RF input.

µF, unless otherwise noted (P=

Waveforms

Page 27

15JF-25H

Page 28

15JF-25H

Schematic Diagram of Mother Unit (F7340N6, 00 Version)

Page 29

4 567

Page 29

Schematic Diagram of Mother Unit (F7340N6, 00 Version)

15JF-25H

Page 30

Page 28

8 9 10 11 121314

Page 30

15JF-25H

Schematic Diagram of Mother Unit (F7340N6, 00 Version)

Page 29

15 16 17 18 19 20 21

Page 31

15JF-25H

Schematic Diagram of CRT Unit (F7341N0, 00 Version)

4567

Page 32

15JF-25H

CRT Unit

BLOCK DIAGRAMS

1 2

4567

Page 33

Mother Unit

15JF-25H

1 234567

Page 34

15JF-25H

TROUBLESHOOTING TABLES

789:;<=>:

^_K`MN

YZ [\]

^_K`eNPcU

rsJSWOdK

YZ [\]

^_K` fNm]NOU

^cU

IJKLnt

OPPKOQOWPcU

urvJqeN

u]weeQOULqv

^_K`MNimINiym^Nn k^NnmpNinOUfriScUK

YZ [\]

IJKL

OPPKOQcU

wOcUxj^Nin

YZ [\]

IJKLMN

OPPKOQ

^_K`I

IJKLaJTKQb\I

RQcd_WQKeVQU

JUX

\YI

fKPSOKW_KqVLK

IJKLMN

OPPKOQ

RSJTUJVW

OcUX

^_K`k^NmINmINnm INmINom^NimpN

[\]YZ

]KKwOUzJqWKUI MSOL_KLcUQKmW_cLcUcOWKLT_c_k^WJ _K`VP

Power LED Flashes

NVM (EEPROM)

(IC1002)

TV PROCESSOR (IC801)

TUNER (TU201)

YZ [\]

^_K`^yNy

^_K`^fe

JUUKWJQgh

^_K`k^ym

k^n

Page 35

NEITHER VERTICAL NOR

HORIZONTAL SYNCHRONIZATION

CIRCUIT TO BE CHECKED:

Sync. Separator Circuit. Check pin33 and 34

of IC801.

DEFECTIVE VERTICEL AMP.

AND VERTICAL LINEARITY

Readjusted vertical size.

(Bass Data)

15JF-25H

Vertical linearity and size

is abnormal.

Check R502,R505

NO VERTICAL SCAN

Check IC501 bias.

Normal Abnormal

Check C502 and C514. Check IC501.

NO SPECIFIC COLOUR

NO YES

Is some colour produced in

B/W broadcast reception?

Check IC801,R801,R802,

R803,D804,D805,D806 properly adjusted?

and Q801.

YES

Is the white balance

Readjusted the white

balance.

The picture colour is cyan. The picture colour is magenta. The picture colour is yellow.

Check Q870,Q885 and Check Q871,Q883 and Check Q872,Q887 and

their adjacent circuits. their adjacent circuits. their adjacent circuits.

Page 36

15JF-25H

NO PICTURE, NO SOUND

CIRCUITS TO BE CHECKED:

Tuner. PIF. Does the noise level increase at max. Automatic Gain Control. Contrast,Brightness and Sound controls? 5V, 32V Power Source.

Noise increase but no No snow noise.

signal is received.

Check the tuner supply voltage Does noise or signal appear

LB and HB must be approx. 5V, at pin40 of IC801?

BT must be approx. 32V,and

CH preset data check.

Normal pin38 of IC801? circuit.

NO YES

Does noise or Check IC801

signal appear at and its related

NO YES

Check the tuner Does noise or

AGC at TP201. signal appear at Check Q401

pin23 and 24 Q402 and related

Normal Abnormal of IC801? circuit.

NO YES

Check pin38 Check pin27 Check pin1,2 of

of IC801. of IC801,Tuner SF201,Tuner Check pin37 of

and related circuit. and related IC801 and

circuit. related circuit.

NO SOUND

CIRCUITS TO BE CHECKED:

Audio Output Circuit. Does signal appear Check IC801 and

at pin6 of IC303? its related circuit.

YES NO

Check Speaker. Check IC303 and

peripheral circuit.

Page 37

15JF-25H

PARTS LISTING

REPLACEMENT PARTS

Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified by

in the Replacement Parts Listing. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended is not permitted. Replacement parts not shown in this service manual may create shock fire, or other hazards.

HOW TO ORDER REPLACEMENT PARTS

To have your order completed promptly and correctly please supply the following information.

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

5. CODE 6. QUANTITY

MARK *: SPARE PARTS DELIVERY SECTION

REF No. PARTS DESCRIPTION * CODE

PICTURE TUBE

VB36AKJ13X/1E 15" FLAT A36AKJ13X01 CHUNGWA S AK RCILGA031WJZZ ADG COIL 15" FLAT S AM QEARCA013WJZZ COATING EARTH 15" S AG LHLDW1514BM00 HOLDER UNEX 2233 S AA LHLDWA011WJKA DEGAUSSING HOLDER 40mm DGCE-4-2-19 S AA

PRINTED WIRING BOARD (Not replacement item)

PWB-A DUNTK7340CJW5 ADJUST CHASSIS 15JF25H S CA PWB-B DUNTK7341BMW5 CRT UNIT 15JF25H S AW

PWB-A MOTHER UNIT

TUNER

TU 0201 VTUCTF5511+++ TUNER THOMSON S AZ

INTEGRATED CIRCUITS

IC 0303 VHIAN7523++-1 IC AN7523 MATSUSHITA S AH IC 0501 VHIAN5522++-1 IC AN5523 MATSUSHITA S AG IC 0601 VHIKA7808AP-1 IC KIA7808API KOREA ELECTRONICS S AE IC 0701 VHITEA1507/-1 IC TEA1507P/N1 PHILIPS S AH IC 0702 RH-FX0008GEZZ P/COUPLER RANK-S SHARP S AD IC 0751 VHITA48M033-1 IC TA48M033F(S) TOSHIBA S AF IC 0801 RH-IX3559CEN1 IC TDA9350PS/NA_A3 PHILIPS S BE IC 1002 VHIM24C08W6-1 IC M24C08-WMN6T ST MICRO S AF

TRANSISTORS

Q 0331 VS2SC3928AR-1 TRANSISTOR S AA Q 0341 VS2SC3928AR-1 TRANSISTOR S AA Q 0342 VS2SC3928AR-1 TRANSISTOR S AA Q 0351 VS2SC3928AR-1 TRANSISTOR S AA Q 0352 VS2SC3928AR-1 TRANSISTOR S AA Q 0401 VS2SC3928AR-1 TRANSISTOR S AA Q 0402 VS2SC3928AR-1 TRANSISTOR S AA Q 0451 VS2SC3928AR-1 TRANSISTOR S AA Q 0501 VS2SC3928AR-1 TRANSISTOR S AA Q 0502 VS2SC3928AR-1 TRANSISTOR S AA Q 0601 VS2SC2482//-1 TRT 2SC2482 TOSHIBA S AC Q 0602 VS2SD2586//1E TRT 2SD2586 TOSHIBA S AK Q 0603 VS2SC3928AR-1 TRANSISTOR S AA Q 0604 VS2SC1815GW-1 TRT NPN 60V 150MA 400MW S AA Q 0605 VS2SA1530ARS1 smt transistor S AA Q 0701 VSSTP4NC80Z1E MOS FET STP4NC80ZFP TOMEN S AH Q 0631 VS2SA1530ARS1 smt transistor S AA Q 0752 VS2SC1815GW-1 TRT NPN 60V 150MA 400MW S AA Q 0753 VS2SC3928AR-1 TRANSISTOR S AA Q 0754 VS2SC3928AR-1 TRANSISTOR S AA Q 1005 VS2SC3928AR-1 TRANSISTOR S AA Q 1006 VS2SC3928AR-1 TRANSISTOR S AA

DIODES

D 0201 RH-EX0676GEZZ ZENER DIODE MTZJ33CT ROHM S AA D 0303 RH-DX0045BMZZ DIODE 1N4148 S AA D 0351 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB

REF No. PARTS DESCRIPTION * CODE

D 0451 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0452 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0453 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0454 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0456 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0457 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0501 RH-DX0131CEZZ DIODE EU-1 SANKEN S AB D 0502 RH-DX0441CEZZ DIODE IN4002G23 GENERAL INSTRUMENT S AB D 0503 RH-EX0684GEZZ ZENER DIODE MTZJ39BT ROHM S AA D 0504 RH-EX0684GEZZ ZENER DIODE MTZJ39BT ROHM S AA D 0505 RH-DX0131CEZZ DIODE EU-1 SANKEN S AB D 0507 RH-EX0603GEZZ Z.DIODE MTZJ 3.9A S AA D 0508 RH-DX0045BMZZ DIODE 1N4148 S AA D 0509 RH-DX0045BMZZ DIODE 1N4148 S AA D 0510 RH-EX0627GEZZ ZENER DIODE MTZJ8.2BT ROHM S AA D 0601 RH-DX0302CEZZ DIODE UZA S AB D 0602 RH-DX0045BMZZ DIODE 1N4148 S AA D 0603 RH-DX0131CEZZ DIODE EU-1 SANKEN S AB D 0604 RH-DX0045BMZZ DIODE 1N4148 S AA D 0605 RH-DX0045BMZZ DIODE 1N4148 S AA D 0606 RH-DX0045BMZZ DIODE 1N4148 S AA D 0607 RH-EX0653GEZZ DIODE ZENER MTZJ18C ROHM S AA D 0608 RH-DX0577BMZZ DIODE 1N4935 ACPA S AE D 0609 VHD1SS244//-1 SW DIODE 1SS244T-72 S AA D 0610 RH-DX0045BMZZ DIODE 1N4148 S AA D 0611 RH-EX0615GEZZ ZENER DIODE 5.6V S AA D 0612 RH-DX0045BMZZ DIODE 1N4148 S AA D 0614 RH-DX0045BMZZ DIODE 1N4148 S AA D 0615 RH-DX0045BMZZ DIODE 1N4148 S AA D 0631 RH-EX0627GEZZ ZENER DIODE MTZJ8.2BT ROHM S AA D 0632 RH-DX0045BMZZ DIODE 1N4148 S AA D 0701 RH-DX0571BMZZ DIODE 1N4005 ACPA S AA D 0702 RH-DX0571BMZZ DIODE 1N4005 ACPA S AA D 0703 RH-DX0571BMZZ DIODE 1N4005 ACPA S AA D 0704 RH-DX0571BMZZ DIODE 1N4005 ACPA S AA D 0705 VHD1SS244//-1 SW DIODE 1SS244T-72 S AA D 0708 RH-DX0045BMZZ DIODE 1N4148 S AA D 0709 RH-EX0656GEZZ ZENER DIODE MTZJ20C ROHM S AA D 0751 RH-DX0302CEZZ DIODE UZA S AB D 0752 RH-DX0064GEZZ DIODE AK04V1 SANKEN S AC D 0753 RH-EX0612GEZZ ZENER DIODE MTZJ5.1BT ROHM S AA D 0754 RH-DX0302CEZZ DIODE UZA S AB D 0755 RH-DX0045BMZZ DIODE 1N4148 S AA D 0756 RH-EX0615GEZZ ZENER DIODE 5.6V S AA D 0759 RH-DX0045BMZZ DIODE 1N4148 S AA D 0804 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0805 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0806 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 0807 RH-EX1399CEZZ ZENER DIODE UDZSTE-179.1B WAKO ELECTRIC S AB D 1001 RH-PX0013PEZZ LED L-53ID-13.95L/F S AB

PACKAGED CIRCUITS

PR 0701 RMPTP0001BMZZ PTC B59250-C1080-B70 S AD X 1001 RCRSB0300CEZZ CRYSTAL HC-49/U-S 12000KHz-A1 MURATA S AF

COILS

L 0201 VP-DF270K0000 PEAK COIL 27UH 10% S AB L 0204 VP-DF270K0000 PEAK COIL 27UH 10% S AB L 0302 VP-DF3R3K0000 PEAK COIL 3,3UH 10% S AB L 0304 VP-DF3R3K0000 PEAK COIL 3,3UH 10% S AB L 0308 VP-CF3R3K0000 PEAK COIL 3.3UH 10% S AB L 0351 VP-DF3R3K0000 PEAK COIL 3,3UH 10% S AB L 0353 VP-DF3R3K0000 PEAK COIL 3,3UH 10% S AB L 0354 VP-DF3R3K0000 PEAK COIL 3,3UH 10% S AB L 0403 VP-XF120K0000 PEAK COIL 12UH 10% 1/8W S AA L 0451 VP-DF3R3K0000 PEAK COIL 3,3UH 10% S AB L 0602 RCILP0225CEZZ COIL SL_A TOKYO S AD L 0603 RCILZA014WJZZ COIL S AG L 0701 RCILF0111BMZZ COIL HR-19043 S AL L 0801 VP-XF100K0000 PEAK COIL 10UH 10% 1/8W S AA L 0802 VP-XF100K0000 PEAK COIL 10UH 10% 1/8W S AA L 1002 VP-XF100K0000 PEAK COIL 10UH 10% 1/8W S AA L 3030 VP-CF3R3K0000 PEAK COIL 3.3UH 10% S AB

CERAMIC FILTERS

Page 38

15JF-25H

REF No. PARTS DESCRIPTION * CODE

CF 0401 RFILC0023CEZZ SOUND FILTER (TAPED) S AD

TRANSFORMERS

T 0601 RTRNZ0026PEZZ DRIVER TRANSFORMER S AE T 0602 RTRNF2053CEZZ FBT BSC21-2643S SHENZHEN S AY T 0701 RTRNWA062WJZZ TRANSF. 15" S AM

CAPACITORS

C 0201 VCEA0A1CW476M ELEC C 47UF 20% 16V S AA C 0202 VCEA0A1AW107M ELEC C 100UF 20% 10V S AA C 0204 VCEA0A1HW106M ELEC C 10UF 20% 50V S AA C 0206 VCKYCY1HF223Z SC CAPACITOR 0.022UF 50V TAPED S AA C 0207 VCKYCY1HB472K S.CHIP CAP 4700PF/50V T S AA C 0208 VCKYCY1HB821K GRM39B 821K 50 (1608)SMD CAPACITOR S AA C 0209 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 0210 VCCCCY1HH220J S. CHIP CAP 22PF/50V TAPED S AA C 0211 VCKYPA1HF103Z C.CAPACITOR 0.01U-F 50V S AA C 0212 VCKYPA1HF103Z C.CAPACITOR 0.01U-F 50V S AA C 0215 VCCCCY1HH220J S. CHIP CAP 22PF/50V TAPED S AA C 0302 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0305 VCEA0A1EW337M ELEC C 330UF 20% 25V S AB C 0307 VCEA0A1CW226M ELEC C 22UF 20% 16V S AA C 0308 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0309 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA C 0310 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0320 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0322 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0324 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0328 VCCCCY1HH221J S. CHIP CAP 220PF/50V TAPED S AA C 0329 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0331 VCEA0A1HW225M ELEC C 2,2UF 20% 50V S AA C 0341 VCKYCY1HB332K s.chip cap 3300pf /50v S AA C 0342 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0343 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0345 VCKYCY1HB222K S CHIP CAPACITOR 0.0022UF/50V TAPED S AA C 0346 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0348 VCEA0A1HW105M ELEC C 1UF 20% 50V S AA C 0349 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0351 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0352 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA C 0354 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA C 0358 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0359 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0361 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0362 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0363 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0402 VCCCCY1HH220J S. CHIP CAP 22PF/50V TAPED S AA C 0403 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0404 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0431 VCKYCY1HF223Z SC CAPACITOR 0.022UF 50V TAPED S AA C 0432 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0433 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 0451 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0453 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0502 VCEA0A1EW477M ELEC C 470UF 20% 25V S AB C 0504 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0505 VCEA0A1HW107M ELEC C 100UF 20% 50V S AA C 0506 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0507 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0508 RC-FZ0272CEZZ C POL P 0,39UF 100V S AC C 0509 VCQYTA2AA563J POL FILM C 56NF 5% 100V S AB C 0511 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0512 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0513 VCKYPA2HB102K CERAM C 1NF 10% 500V S AA C 0514 VCEA0A1EW477M ELEC C 470UF 20% 25V S AB C 0515 VCQYTA1HM103J F. CAPACITOR 0.01UF/50V S AA C 0521 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0522 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0531 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0532 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0533 VCQYTA1HM104J F. CAPACITOR 0.1 UF 50 V S AA C 0599 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0602 VCEA0A1CW477M ELEC C 470UF 20% 16V S AA C 0603 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA

REF No. PARTS DESCRIPTION * CODE

C 0604 VCKYPA1HF103Z C.CAPACITOR 0.01U-F 50V S AA C 0605 VCEA0A1AW227M ELEC C 220UF 20% 10V S AA C 0606 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA C 0607 VCKYPA1HF103Z C.CAPACITOR 0.01U-F 50V S AA C 0608 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 0609 VCKYPA2HB102K CERAM C 1NF 10% 500V S AA C 0610 VCFYSB2EB823J POL FILM C 82NF 5% 100V S AB C 0611 VCFPVC3CA762H PP FILM C 7,6NF 3% 1,6KV S AC C 0614 VCFPVC2DB274J PP FILM C 270NF 5% 200V S AB C 0615 RC-EZ0724CEZZ ELEC C 100UF 160V KMF160VB-100MMC NICHIC S AE C 0616 VCQYTA1HM104J F. CAPACITOR 0.1 UF 50 V S AA C 0617 VCEA0A1HW105M ELEC C 1UF 20% 50V S AA C 0619 VCEA0A1HW106M ELEC C 10UF 20% 50V S AA C 0620 VCKYPA2HB221K CERAM C 220PF 10% 500V S AA C 0621 VCEA0A2CW105M ELEC C 1UF 20% 160V S AA C 0622 VCEA0A1CW227M E CAPACITOR 220UF 16V 6.3x11 S AB C 0631 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 0632 VCKYCY1HB222K S CHIP CAPACITOR 0.0022UF/50V TAPED S AA C 0633 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA C 0701 RC-FZ0176BMZZ POL C B81130 100NF 275V X2 S AB C 0702 RC-KZ0029CEZZ CERAM C 10NF 80,20% 250V S AC C 0703 RC-KZ0029CEZZ CERAM C 10NF 80,20% 250V S AC C 0704 RC-KZ0029CEZZ CERAM C 10NF 80,20% 250V S AC C 0705 RC-EZ0150BMZZ ELEC C 100uF 400V LPN100M2GN JAMICON S AM C 0707 VCEA0A1EW107M E. CAPACITOR 100UF 25V 6.3x11 S AA C 0708 VCQYTA1HM104J F. CAPACITOR 0.1 UF 50 V S AA C 0709 VCFYFA1HA474J FILM CAPACITOR 474 MAT S AB C 0710 RC-KZ0040CEZZ CERAM C 820PF 2KV S AD C 0712 RC-KZ0105GEZZ C. CAP 2200PF/4KV-KX S AB C 0713 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0716 VCKYPA2HB102K CERAM C 1NF 10% 500V S AA C 0751 RC-KZ0299CEZZ CERAM C DE1105-979BN821K2K-A3 MURATA S AB C 0752 RC-EZ0724CEZZ ELEC C 100UF 160V KMF160VB-100MMC NICHIC S AE C 0753 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0754 VCEA0A1CW108M ELEC C 1000MF 16V 10X16MM S AB C 0755 VCEA0A1CW227M E CAPACITOR 220UF 16V 6.3x11 S AB C 0756 VCEA0A0JW227M E CAPACITOR 220UF/6.3V-5X11 S AA C 0757 VCKYPA2HB102K CERAM C 1NF 10% 500V S AA C 0758 VCEA0A1EW477M ELEC C 470UF 20% 25V S AB C 0759 VCKYPA1HB102K C.CAPACITOR 1000PF/50V S AA C 0761 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 0762 VCCCPA1HH680J CERAM C 68PF 5% 50V S AA C 0764 VCEA0A1EW107M E. CAPACITOR 100UF 25V 6.3x11 S AA C 0765 VCEA0A1CW107M ELEC C 100UF 20% 16V S AA C 0767 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0801 VCEA0A1CW227M E CAPACITOR 220UF 16V 6.3x11 S AB C 0803 VCFYFA1HA224J PP FILM C 220NF 5% 50V S AA C 0804 VCFYFA1HA224J PP FILM C 220NF 5% 50V S AA C 0805 VCKYCY1HB222K S CHIP CAPACITOR 0.0022UF/50V TAPED S AA C 0806 VCEA0A1HW105M ELEC C 1UF 20% 50V S AA C 0807 VCKYCY1HB472K S.CHIP CAP 4700PF/50V T S AA C 0808 VCKYCY1HF223Z SC CAPACITOR 0.022UF 50V TAPED S AA C 0809 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA C 0810 VCEA0A1HW474M ELEC C 0,47UF 20% 50V S AA C 0811 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0812 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0813 VCKYCY1HB102K S. CHIP CAP 0.001UF/50V S AA C 0814 VCKYCY1HB561K S. CAPACITOR 560PF/50V S AA C 0815 VCEA0A1CW227M E CAPACITOR 220UF 16V 6.3x11 S AB C 0817 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0818 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0819 VCEA0A1CW227M E CAPACITOR 220UF 16V 6.3x11 S AB C 0822 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 0823 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 1001 VCCCCY1HH330J S. CHIP CAP 33PF/50V S AA C 1002 VCCCCY1HH330J S. CHIP CAP 33PF/50V S AA C 1004 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 1006 VCKYCY1HF223Z SC CAPACITOR 0.022UF 50V TAPED S AA C 1009 VCEA0A0JW107M ELEC C 100UF 20% 6,3V S AA C 1011 VCEA0A0JW107M ELEC C 100UF 20% 6,3V S AA C 1012 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA C 1013 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 1014 VCEA0A0JW107M ELEC C 100UF 20% 6,3V S AA C 1015 VCEA0A1CW106M ELEC C 10UF 20% 16V S AA

Page 39

15JF-25H

REF No. PARTS DESCRIPTION * CODE

C 1017 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 1018 VCKYCY1HF103Z CHIP CAP 0.01UF/50V S AA C 1020 VCKYCY1EF104Z S CHIP TAPE CAP 0.1UF/25V S AA

RESISTORS

R 0201 VRD-RA2BE332J RES 3,3KOHM 5% 1/8W S AA R 0202 VRS-CY1JF681J S. CHIP RES. 680-OHM TAPED S AA R 0208 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0209 VRS-CY1JF391J SURFACE MOUNT CHIP RESISTOR 390 OHM S AA R 0290 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0302 VRS-CY1JF472J S. RES. 4.7K OHM TAPED S AA R 0303 VRD-RA2BE331J RES 330 OHM 5% 1/8W S AA R 0306 VRS-CY1JF392J S. CHIP RES. 3.9K-OHM TAPED S AA R 0308 VRS-CY1JF471J S. CHIP RES. 470-OHM TAPED S AA R 0309 VRS-CY1JF471J S. CHIP RES. 470-OHM TAPED S AA R 0310 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0311 VRD-RA2HD680J RES 68 OHM 5% 1/2W S AA R 0312 VRS-CY1JF682J S. CHIP RES. 6.8 K OHM TAPED S AA R 0313 VRS-CY1JF223J S.CHOP REG 22K-OHM T S AA R 0331 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 0332 VRS-CY1JF473J S. CHIP RES 47K-OHM TAPED S AA R 0333 VRD-RA2BE103J RES 10KOHM 5% 1/8W S AA R 0339 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0340 VRS-CY1JF821J S. CHIP RES. 820-OHM S AA R 0341 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0342 VRS-CY1JF821J S. CHIP RES. 820-OHM S AA R 0343 VRS-CY1JF471J S. CHIP RES. 470-OHM TAPED S AA R 0344 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0351 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0352 VRS-CY1JF104J S. CHIP RES. 100K-OHM TAPED S AA R 0356 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0357 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 0359 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0360 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 0362 VRS-CY1JF472J S. RES. 4.7K OHM TAPED S AA R 0363 VRS-CY1JF104J S. CHIP RES. 100K-OHM TAPED S AA R 0364 VRS-CY1JF472J S. RES. 4.7K OHM TAPED S AA R 0365 VRS-CY1JF104J S. CHIP RES. 100K-OHM TAPED S AA R 0366 VRS-CY1JF561J S. CHIP RES 560-OHM TAPED S AA R 0367 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0390 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0391 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0401 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0403 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0405 VRS-CY1JF181J S CHIP RES. 180-OHM TAPED S AA R 0406 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0407 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0408 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0409 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA R 0451 VRD-RA2EE750J RES 75 OHM 5% 1/4W S AA R 0452 VRS-CY1JF104J S. CHIP RES. 100K-OHM TAPED S AA R 0453 VRS-CY1JF223J S.CHOP REG 22K-OHM T S AA R 0454 VRS-CY1JF562J S. CHIP RES. 5.6K-OHM TAPED S AA R 0455 VRD-RA2EE750J RES 75 OHM 5% 1/4W S AA R 0456 VRD-RA2EE750J RES 75 OHM 5% 1/4W S AA R 0457 VRD-RA2EE750J RES 75 OHM 5% 1/4W S AA R 0458 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 0459 VRD-RA2EE750J RES 75 OHM 5% 1/4W S AA R 0460 VRD-RA2EE750J RES 75 OHM 5% 1/4W S AA R 0461 VRD-RA2BE224J RES 220KOHM 5% 1/8W S AA R 0490 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0491 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0492 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0501 VRD-RA2BE392J RES 3,9KOHM 5% 1/8W S AA R 0502 VRN-VV3DB2R7J MET FILM R 2,7 OHM 5% 2W S AB R 0503 VRD-RA2HD331J RES 330 OHM 5% 1/2W S AA R 0504 VRS-CY1JF181J S CHIP RES. 180-OHM TAPED S AA R 0505 VRD-RA2BE1R0J RES 1 OHM 5% 1/8W S AA R 0507 VRS-CY1JF181J S CHIP RES. 180-OHM TAPED S AA R 0509 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA R 0511 VRD-RA2HD102J RES 1KOHM 5% 1/2W S AA R 0512 VRD-RA2BE100J RES 10 OHM 5% 1/8W S AA R 0513 VRD-RA2BE103J RES 10KOHM 5% 1/8W S AA R 0514 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA

REF No. PARTS DESCRIPTION * CODE

R 0515 VRS-CY1JF153J S CHIP RES. 15K-OHM TAPED S AA R 0516 VRS-CY1JF153J S CHIP RES. 15K-OHM TAPED S AA R 0517 VRS-CY1JF223J S.CHOP REG 22K-OHM T S AA R 0518 VRS-CY1JF334J S. CHIP RES. 330K-OHM TAPED S AA R 0531 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0532 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0533 VRD-RA2BE393J RES 39KOHM 5% 1/8W S AA R 0603 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA R 0604 VRD-RA2HD472J RES 4.7KOHM 5% 1/2W S AA R 0605 VRS-KT3LB332J MET OX RES 3,3KOHM 5% 3W S AD R 0606 VRD-RA2HD102J RES 1KOHM 5% 1/2W S AA R 0607 VRD-RA2BE104J RES 100KOHM 5% 1/8W S AA R 0608 VRN-RV3AB1R8J MET FILM R 1.8 OHM 5% 1W S AA R 0609 VRD-RA2HD101J RES 100 OHM 5% 1/2W S AA R 0610 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0611 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 0612 VRD-RA2BE331J RES 330 OHM 5% 1/8W S AA R 0613 VRD-RA2HD184J RES 180KOHM 5% 1/2W S AA R 0614 VRD-RA2HD472J RES 4.7KOHM 5% 1/2W S AA R 0615 VRD-RA2HD472J RES 4.7KOHM 5% 1/2W S AA R 0616 VRD-RA2HD182J RES 1,8KOHM 5% 1/2W S AA R 0618 VRD-RA2BE123J RES 12KOHM 5% 1/8W S AA R 0619 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 0620 VRD-RA2HD220J RES 22 OHM 5% 1/2W S AA R 0621 VRD-RA2HD820J RES 82 OHM 5% 1/2W S AA R 0622 VRD-RA2HD222J RES 2,2KOHM 5% 1/2W S AA R 0623 VRG-RL2HB562J FUS RES 5,6KOHM 5% 1/2W S AB R 0624 VRD-RA2BE123J RES 12KOHM 5% 1/8W S AA R 0625 VRD-RA2BE103J RES 10KOHM 5% 1/8W S AA R 0626 VRS-CY1JF562J S. CHIP RES. 5.6K-OHM TAPED S AA R 0627 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 0629 VRD-RA2EE151J RES 150 OHM 5% 1/4W S AA R 0630 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0631 VRD-RA2BE391J RES 390 OHM 5% 1/8W S AA R 0632 VRD-RA2BE273J RES 27KOHM 5% 1/8W S AA R 0633 VRS-CY1JF822J S. CHIP RES. 8.2K-OHM TAPED S AA R 0634 VRS-CY1JF102J S.CHIP RES TAPE 1K OHM S AA R 0636 VRS-CY1JF154J S CHIP RES. 150K-OHM TAPED S AA R 0637 VRS-CY1JF273J S. CHIP RES. 27-OHM TAPED S AA R 0638 VRS-CY1JF221J S. CHIP RES. 220-OHM TAPED S AA R 0639 VRD-RA2BE333J RES 33KOHM 5% 1/8W S AA R 0640 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 0701 VRW-KP3HC5R6K WOUND RES 5,6 OHM 10% 5W S AC R 0706 VRD-RA2BE122J RES 1,2KOHM 5% 1/8W S AA R 0707 VRD-RA2BE393J RES 39KOHM 5% 1/8W S AA R 0708 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA R 0710 VRN-VV3ABR27J MET FILM R .27 OHM 5% 1W S AA R 0711 VRD-RA2BE270J RES 27 OHM 5% 1/8W S AA R 0712 VRD-RA2HD100J RES 10 OHM 5% 1/2W S AA R 0713 VRD-RA2BE394J RES 390KOHM 5% 1/8W S AA R 0716 RR-HZ0014GEZZ high vol. resistor 12m ohm S AC R 0718 VRD-RA2BE824J RES 820KOHM 5% 1/8W S AA R 0752 VRD-RA2HD102J RES 1KOHM 5% 1/2W S AA R 0753 VRN-VV3DB5R6J MET FILM R 5.6 OHM 5% 2W S AA R 0761 VRD-RA2BE681J RES 680 OHM 5% 1/8W S AA R 0762 VRD-RA2HD184J RES 180KOHM 5% 1/2W S AA R 0763 VRD-RA2BE822J RES 8,2KOHM 5% 1/8W S AA R 0766 VRD-RA2EE183J RES 18KOHM 5% 1/4W S AA R 0768 VRD-RA2HD124J RES 120KOHM 5% 1/2W S AA R 0770 VRD-RA2HD181J RES 180 OHM 5% 1/2W S AA R 0771 VRD-RA2HD181J RES 180 OHM 5% 1/2W S AA R 0772 VRS-CY1JF333J S. CHIP RES. 33K-OHM TAPED S AA R 0773 VRS-CY1JF153J S CHIP RES. 15K-OHM TAPED S AA R 0774 VRS-CY1JF332J S. CHIP RES. 3.3K-OHM TAPED S AA R 0801 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0802 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0803 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0804 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0805 VRS-CY1JF223J S.CHOP REG 22K-OHM T S AA R 0806 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0807 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0808 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 0809 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1001 VRS-CY1JF181J S CHIP RES. 180-OHM TAPED S AA

Page 40

15JF-25H

REF No. PARTS DESCRIPTION * CODE

R 1002 VRS-CY1JF221J S. CHIP RES. 220-OHM TAPED S AA R 1003 VRS-CY1JF331J S CHIP RES TAPE 330 OHM S AA R 1004 VRS-CY1JF681J S. CHIP RES. 680-OHM TAPED S AA R 1005 VRS-CY1JF472J S. RES. 4.7K OHM TAPED S AA R 1006 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1008 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 1009 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 1014 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 1015 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 1016 VRD-RA2BE332J RES 3,3KOHM 5% 1/8W S AA R 1017 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 1018 VRD-RA2BE332J RES 3,3KOHM 5% 1/8W S AA R 1019 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1020 VRS-CY1JF153J S CHIP RES. 15K-OHM TAPED S AA R 1022 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1023 VRD-RA2BE153J RES 15KOHM 5% 1/8W S AA R 1024 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1025 VRS-CY1JF122J S. RESISTOR 1.2K OHM S AA R 1026 VRS-CY1JF224J S. CHIP RES. 220K-OHM TAPED S AA R 1027 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1028 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 1029 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1033 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1034 VRD-RA2BE332J RES 3,3KOHM 5% 1/8W S AA R 1035 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1036 VRD-RA2BE332J RES 3,3KOHM 5% 1/8W S AA R 1037 VRD-RA2BE101J RES 100 OHM 5% 1/8W S AA R 1038 VRS-CY1JF223J S.CHOP REG 22K-OHM T S AA R 1040 VRS-CY1JF152J S. CHIP RES. 1.5K-OHM S AA R 1041 VRS-CY1JF152J S. CHIP RES. 1.5K-OHM S AA R 1043 VRS-CY1JF562J S. CHIP RES. 5.6K-OHM TAPED S AA R 1044 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 1047 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 1048 VRS-CY1JF391J SURFACE MOUNT CHIP RESISTOR 390 OHM S AA R 1052 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 1053 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA R 1054 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA R 1056 VRS-CY1JF103J S.C. RESISTOR 10K OHM S AA R 1057 VRS-CY1JF472J S. RES. 4.7K OHM TAPED S AA R 1058 VRS-CY1JF101J S. CHIP RES. 100-OHM TAPED S AA

MISCELLANEOUS PARTS

LHLDP1066PE00 LED HOLDER S AB F 0701 QFS-C3229CEZZ FUSE S506-3.15A-A1 TOKYO COMPONENTS S AC F 0751 QFS-J2521CEZZ FUSE 2,5A 125V LITTELFUSE (KURODA9 S AD FB 0451 RBLN-0037CEZZ BALUN FBA04HA90088-00 T/Y S AB FB 0452 RBLN-0037CEZZ BALUN FBA04HA90088-00 T/Y S AB FB 0601 RBLN-0037CEZZ BALUN FBA04HA90088-00 T/Y S AB FB 0701 RBLN-0037CEZZ BALUN FBA04HA90088-00 T/Y S AB FH 0701 QFSHD1001BMZZ FUSE HOLD.EYF52BC=PANASON S AA FH 0702 QFSHD1002BMZZ FUSE HOLD.EYF52BC=PANASON S AA JK 3001 QJAKJ0047CEZZ EARPHONE JACK HSJ0998-72 S AG P 0301 QPLGN0241CEZZ PLUG S AA P 0601 QPLGN0441CEZZ PLUG 4PIN S AA P 0602 QPLGN0560CEZZ CONNECTOR 5 PIN TV-50P-05-V2 A TAIKO S AB P 0701 QPLGN0360CEZZ CONNECTOR 3 PIN TV-50P-03-V2 A TAIKO S AA P 0702 QPLGN0260CEZZ CONNECTOR 2 PIN TV-50P-02-V2 A TAIKO S AA P 0801 QPLGN0541CEZZ PLUG S AA P 1001 QPLGN0641CEZZ PLUG S AA RJ 0001 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0004 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0007 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0008 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0009 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0010 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0019 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0020 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0024 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0026 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0027 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0029 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0031 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0033 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0035 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA

REF No. PARTS DESCRIPTION * CODE

RJ 0036 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0044 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0046 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0047 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0048 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0055 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0056 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0057 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0058 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0059 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0061 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0062 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0064 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0065 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0067 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0068 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0070 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0071 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0072 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0074 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0080 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0084 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RJ 0085 VRS-CY1JF000J S. CHIP RES. 0-OHM TAPED S AA RMC1001 RRMCU0255CEZZ R/C RECEIVER TSOP1838UH1 ELEKTRA VISHAY S AG S 0701 QSW-P0591CEZZ SWITCH SDDFC3-A ALPS S AL S 1001 QSW-K0003AJZZ SWITCH S AA S 1002 QSW-K0003AJZZ SWITCH S AA S 1003 QSW-K0003AJZZ SWITCH S AA S 1004 QSW-K0003AJZZ SWITCH S AA S 1005 QSW-K0003AJZZ SWITCH S AA SC 0451 QSOCZ2107BMZZ SOCKET S AE SF 0201 RFILC0282BMZZ SAW FILTER J1952M 38.90MHZ S AM VA 0701 RH-VX0047CEZZ VARISTOR SIOV-S14K420M4 MATSUSHITA S AC

PWB-B CRT UNIT

TRANSISTORS

Q 0870 VSBF422////-1 TRT BF422 PHILIPS S AA Q 0871 VSBF422////-1 TRT BF422 PHILIPS S AA Q 0872 VSBF422////-1 TRT BF422 PHILIPS S AA Q 0883 VSBF421////-1 TRT BF421 PHILIPS S AA Q 0885 VSBF421////-1 TRT BF421 PHILIPS S AA Q 0887 VSBF421////-1 TRT BF421 PHILIPS S AA

DIODES

D 0811 RH-DX0045BMZZ DIODE 1N4148 S AA D 0812 RH-DX0045BMZZ DIODE 1N4148 S AA D 0880 VHD1SS82///1A DIODE 1SS82-A HITACHI S AB D 0881 VHD1SS82///1A DIODE 1SS82-A HITACHI S AB D 0882 VHD1SS82///1A DIODE 1SS82-A HITACHI S AB

CAPACITORS

C 0871 VCKYPA1HB471K CERAM C 470PF 10% 50V S AA C 0872 VCKYPA1HB471K CERAM C 470PF 10% 50V S AA C 0873 VCKYPA1HB471K CERAM C 470PF 10% 50V S AA C 0875 VCKYPA2HB102K CERAM C 1NF 10% 500V S AA C 0876 RC-KZ0150CEZZ CERAM C DE0707-726E102Z3K-A MURATA S AB C 0878 VCEAGA2EW336M ELEC C 33UF 20% 250V S AD C 0880 VCKYPA1HB471K CERAM C 470PF 10% 50V S AA C 0881 VCKYPA1HB471K CERAM C 470PF 10% 50V S AA C 0882 VCKYPA1HB471K CERAM C 470PF 10% 50V S AA

RESISTORS

R 0870 VRD-RA2BE563J RES 56KOHM 5% 1/8W S AA R 0879 VRD-RA2BE471J RES 470 OHM 5% 1/8W S AA R 0880 VRD-RA2BE471J RES 470 OHM 5% 1/8W S AA R 0881 VRD-RA2BE471J RES 470 OHM 5% 1/8W S AA R 0882 VRS-VV3DB153J MET OX RES 15KOHM 5% 2W S AA R 0883 VRD-RA2HD272J RES 2,7KOHM 5% 1/2W S AA R 0884 VRS-VV3DB153J MET OX RES 15KOHM 5% 2W S AA R 0885 VRD-RA2HD272J RES 2,7KOHM 5% 1/2W S AA R 0886 VRS-VV3DB153J MET OX RES 15KOHM 5% 2W S AA R 0887 VRD-RA2HD272J RES 2,7KOHM 5% 1/2W S AA R 0888 VRD-RA2BE471J RES 470 OHM 5% 1/8W S AA R 0892 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA

Page 41

REF No. PARTS DESCRIPTION * CODE

R 0893 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA R 0894 VRD-RA2BE102J RES 1KOHM 5% 1/8W S AA R 0898 VRD-RA2BE471J RES 470 OHM 5% 1/8W S AA R 0899 VRD-RA2BE471J RES 470 OHM 5% 1/8W S AA

MISCELLANEOUS PARTS

P 0851 QPLGN0441CEZZ PLUG 4PIN S AA P 0882 QPLGN0541CEZZ PLUG S AA P 0883 QTIPM0017CEFM TIP S AA SC 0881 QSOCV0017PEZZ CRT SOCKET ISMM04S INCHANG S AE

MISCELLANEOUS PARTS

CACCB5008BMV0 A.C CORD S AT LHLDKA001WJZZ AC CORD HOLDER S AA LHLDW1009CEZZ HOLDER S AA LHLDW1060CEZZ HOLDER S AA LHLDZ1714BMZZ HOLDER ANODE CAP S AA QCNW-5971CEZZ WIRE (SP) S AC RRMCG1060BMSA R/C 37DT25S S AU SPAKPA060WJZZ CEL-AIR WRAPPER S AA SPAKR500A1650 WRAPPER BOBINE 15" JF S -UBATU0013TAZZ BATTERY R6(X2) TOSHIBA S AC LHLDW1033CE00 HOLDER S AA QACCB5008BMZZ AC CORD S AQ QSOCN0302CEZZ SOCKET SMK W-A5303-1N S AB LHLDZ0015PEZZ HOLDER S -LHLDZ0147PEZZ HOLDER S -SPAKAA024WJZZ CENTER BOARD S -SPAKAA026WJZZ SIDE BOARD S -SPAKAA027WJZZ TOP-BTM BOARD S -SPAKAA028WJZZ REAR BOARD S -SPAKKA014WJZZ CASE S -SPAKPA024WJZZ MIRROR MAT S -GBFL-0014PEKA SPEAKER SUPPORT S AD

SP 0301 VSP9050PB33WA SPEAKER 509SF32C001MA MISAWA S AK

SPAKAA025WJZZ FRONT BOARD S -SPAKAA029WJZZ CENTER BOARD S -SPAKAA030WJZZ SIDE BOARD S -SPAKAA031WJZZ TOP-BTM BOARD S -SPAKAA032WJZZ FRONT-REAR BOARD S -SPAKKA015WJZZ CASE S -SPAKPA025WJZZ MIRROR MAT S -LHLDZA030WJZZ FBT HOLDER S AE TGAN-3170UMZZ UK GUARANTEE S AA TINS-7242BMN0 QUICK GUIDE 15JF25H S AC TINS-7246BMN0 OWNERS MANUAL 15JF25H S AK SPAKCA108WJZZ PACKING CASE S AV SPAKXA042WJZZ PACKING-AD S AQ LHLDW1033CE00 HOLDER S AA QCNW-A510WJZZ (H) WIRE S AC QCNW-A511WJZZ (K) WIRE S AC XTASD30P12000 SCREW S AA GCOVHA009WJSA BATTERY COVER R/C HTR0222-720010 HOSIDEN S --

15JF-25H

1.2 1.3 1.4

1.1

*Do not retrieve to remove the Rear Cabinet.

CABINET PARTS

1 CCABAA082BMV1 CABINET SET + ELEC ASS 15JF25H S BK

1.1 JBTN-A025WJSA POWER BUTTON S AC

1.2 GCOVAA074WJSA R/C LED COVER S AD

1.3 HDECAA001WJSB SP DECORATION S AF

1.4 JBTN-0403PESA CONTROL BUTTON S AD 2 GCABBA023WJKA REAR CABINET S -3 XTASB40P20000 SCREW S AA 4 XTASD40P12000 SCREW S AA

Page 42

15JF-25H

ACCESSORIES

R/C Battery Cover

GCOVHA009WJSA

Remote Control

RRMCG1060BMSA

1. TDA93XX, Philips Data Sheet: TDA935X/6X/8X PS/N2 series, TV signal processor-Teletext decoder with embedded µ-Controller.

Tentative Device Specification, 2001 Aug 29, Version: 1.8.

2. TEA1507, Philips Data Sheet: TEA1507 GreenChipII SMPS controlIC. Preliminary specification, 2000Dec05.

Batteries R6(x2)

Operation Manual Set

UBATU0013TAZZ

COLOUR TELEVISION

MODEL

15JF-25H

OPERATION MANUAL

Please read this operation manual carefully before using the colour television.

PRINTED ON ENVIRONMENTALLY FRIENDLY PAPER

SOURCE OF DOCUMENTATION

TINS-7246BMN0, Operation Manual

TGAN-3170UMZZ, Guarantee Card

TINS-7242BMN0, Quick start Guide

3. AN7523, Matsushita Electronics Corporation Specifications: AN7523 Product Specifications. Doc No. SDSC-PSE-AN7503, Eff. Date 23-FEB-01.

4. AN5522, Matsushita Electronics Corporation Specifications: AN5522 Product Specifications. Doc No. SDSC-PSE-AN5522, Eff. Date 21-NOV-2000.

Page 43

Notes:

15JF-25H

Page 44

15JF-25H

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

SHARP ELECTRONICA ESPAÑA S.A. TV Division Engineering Dept. Polígono Industrial Can Sant Joan Sant Cugat del Vallès Barcelona Spain

PRINTED BY: ON:

Think Ecology, please use

RECYCLED PAPER