Page 1
14U-FM1
CU14FM1
SERVICE MANUAL
S32G614U-FM1/
COLOR TELEVISION
Chassis No. GA-2
14U-FM1
MODELS
In the interests of user-safety (Required by saf ety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
CU14FM1
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS .........................................................................................................1
» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................2
» LOCATION OF USER'S CONTROL .....................................................................................................6
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................7
» SERVICE MODE...................................................................................................................................8
» ADJUSTMENT METHOD ...................................................................................................................13
» CHASSIS LAYOUT .............................................................................................................................26
» BLOCK DIAGRAM ..............................................................................................................................27
» SCHEMATIC DIAGRAMS ...................................................................................................................32
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................38
» REPLACEMENT PARTS LIST ............................................................................................................41
» PACKING OF THE SET ......................................................................................................................47
ELECTRICAL SPECIFICATIONS
POWER INPUT.....................................................AC 120 V, 60 Hz
POWER RATING ....................................................................70 W
PICTURE SIZE ............................................... 607 cm2 (94sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ..................................................... 3 W (RMS)
SPEAKER
SIZE .............................................................................. 5 x 9 cm
VOICE COIL IMPEDANCE............................. 16 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF.....................................................75 ohm Unbalanced
TUNING RANGES
VHF-Channels...............................................................2 thru 13
UHF-Channels ............................................................14 thru 69
CATV Channels...........................................................1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
Page 2
14U-FM1
CU14FM1
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC pow er before servicing.
3. Semiconductor heat sinks are potential shock hazards
when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
4A 125V
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral implosion
protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
X-RADIATION AND HIGH VOLTA GE LIMITS
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However , the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that ser vicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be k ept at the rated v alue
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessiv e high voltage, a void being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
2
Page 3
2
2
2
IMPORTANT SERVICE SAFETY PRECAUTION
1.5k ohm
10W
0.15 F
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
(Continued)
14U-FM1
CU14FM1
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the A C voltage drop
across the resistor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessar y, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp .
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
3
Page 4
14U-FM1
CU14FM1
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ë
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur av ant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur a deux systèmes de mise
à la terre qui sont séparés par un matériau isolant.
Le système de mise à la terre non-isolée (chaud) est
pour le circuit du régulateur de tension B+ et le circuit
de sortie horizontale. Le système de mise à la terre
isolé est pour les basses tensions C. C . B+ et le circuit
secondaire du transformateur de haute tension.
PRECAUTION:POUR LA
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
4A 125V
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V .
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 k en série a vec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le cor den d'alimentation doit être
retiré de la prise murale.)
1. Il est à noter que le tube-image de ce récepteur est
intégralement protégé contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesur ables si la haute tension est mainten ue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est excessive
que les rayons X peuv ent entrer dans l'en v eloppe du
tube-image y compris le conducteur de verre. Il est
important de maintenir la haute tension en-dessous
du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
voltmètre à haute tension qui doit être périodiquement
étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime-et pas plus haute. L'opération à des
tensions plus élevées peut entraîner une panne du
tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation X.
Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive, éviter de s'approcher inutilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
4
Page 5
14U-FM1
2
2
CU14FM1
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
» Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
» A l'aide de deux fils à pinces, brancher une résistance
de 1,5 k 10 w atts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
» Utiliser un voltmètre CA d'une sensibilité d'au moins
5000 /V pour mesurer la chute de tension en tr avers
de la résistance.
» Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance.
Toutes les vérifications doivent être refaites après
avoir inversé la fiche du cordon d'alimentation. (Si
nécessaire, une prise d'adpatation non polarisée peut
être utilisée dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
Voltmètre CA
1.5k ohm
10W
0.15 F
SONDE D’ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
BRANCHER A UNE
TERRE CONNUE
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
identifiées par la marque "
å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
5
Page 6
14U-FM1
CU14FM1
LOCATION OF USER'S CONTROL
Front Panel
SENSOR AREA FOR
REMOTE CONTROL
POWER
Press → On.
Press again → Off.
MENU.
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
Basic Remote Control Functions
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
VOLUME UP/DOWN
(+) Increases sound.
(—) Decreases sound.
¥ In menu mode, changes or selects
the TV adjustments.
MUTE
Press → Mutes sound.
Press again → Restores sound.
¥ CLOSED CAPTION appears when
sound is muted.
VOLUME UP/DOWN
(+) Increases sound.
(—) Decreases sound.
VIDEO IN AUDIO
TERMINALS
CHANNEL UP/DOWN
(
') Selects next higher channel.
) Selects next lower channel.
(
"
Infrared Transmitter Window
INPUT
Press → Switch to e xternal video input
mode.
Press again → Switch to TV mode.
CHANNEL UP/DOWN
(
') Selects next higher channel.
) Selects next lower channel.
(
"
¥ Moves the • mark of the MENU
screens.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
DISPLAY
Press → Displa ys receiving channel for
four seconds.
Press again → Removes display.
¥ Temporarily displays receiving
channel when in Closed Caption
mode.
TV
6
Page 7
14U-FM1
CU14FM1
INSTALLATION AND SERVICE INSTRUCTIONS
Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2)Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for accur ate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 21.0 ±1.3V.
5. Apply external 27.0V DC at TP653 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and mak e
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
HIGH VOLT A GE CHECK
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 26.5kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the v oltage test,
make Y-mute off to the normal mode.
7
Page 8
14U-FM1
CU14FM1
SERVICE MODE
Service Mode Overview
1. Service mode is entered by SERVICE key input or CH-UP +VOL-DOWN input during reset.
2. Service mode is cleared by entering SERVICE key or CH-UP +VOL-DOWN key command during service mode.
3. If key input port (SERVICE) input is LOW, then it is in service mode.
4. During key input port (SERVICE) input is LOW, clearing service mode by key input SERVICE or CH-UP + VOLDOWN is disabled.
5. Service mode can be switched to 4 modes as follows by key input MENU;
Option mode
Adjustment mode
Setting mode
Check mode
6. AFT processing is disabled during service mode. PLL setting data is set to fo data.
7. All user data are set to default during service mode. FAO and SPEAKER user settings are off and on respectively
in service mode. Energy Save is off.
8. Sleep timer, View timer and Off timer are inactivated in Service mode.
9. Sound is muting in service mode except at Adjustment Items V20, M01, M02, M03, M04, M05, and M06.
First mode of service mode when SERVICE key is
pressed.
First mode of service mode when local key
CH-UP + VOL-DOWN is pressed after MCU reset.
8
Page 9
Adjustment Mode Items
No. Item Name IC Register Range Default
V01 SUB-PICTURE 1 Chip CONTRAST 0~127 127
V02 SUB-TINT 1 Chip TINT 0~127 64
V03 SUB-COLOR 1 Chip COLOR 0~127 64
V04 SUB-BRIGHT 1 Chip BRIGHT 0~255 128
V05 SUB-SHARP 1 Chip VIDEO-TONE 0~63 32
V06 V-SHIFT 1 Chip V-SHIFT 0~7 4
V07 H-SHIFT 1 Chip H-PHASE 0~31 16
V08 RF-AGC 1 Chip RF-Delay 0~127 127
V09 V-SIZE 1 Chip V-SIZE 0~63 32
V10 PIF-VCO 1 Chip VIF-VCO 0~63 32
V11 R-CUTOFF 1 Chip R-CUTOFF 0~255 127
V12 G-CUTOFF 1 Chip G-CUTOFF 0~255 127
V13 B-CUTOFF 1 Chip B-CUTOFF 0~255 127
V14 R-DRIVE 1 Chip R-DRIVE 0~127 64
V15 B-DRIVE 1 Chip B-DRIVE 0~127 64
V16 SUB-COLOR(YUV) 1 Chip COLOR 0~127 64
V17 SUB-TINT(YUV) 1 Chip BASEBAND-TINT 0~127 64
V18 CC-POS Micron 0~255 32
V19 (Vertical mode) 1 Chip V-MUTE,SERVICE 0, 1, 2 0
V20 SUB-VOL 1 Chip A-ATT 0~127 127
V21 H-VCO 1 Chip H-VCO 0~7 4
M01 MTS-ATT MTS ATT 0~15 10
M02 MTS-VCO MTS VCO 0~63 32
M03 MTS-FILTER MTS FILTER 0~63 28
M04 MTS-WIDEBAND MTS WIDEBAND 0~63 27
M05 MTS-SPECTRAL MTS SPECTRAL 0~63 32
M06 SUB-VOL MTS VOL 0~63 63
14U-FM1
CU14FM1
9
Page 10
14U-FM1
CU14FM1
Ë
SELF ADJUSTMENT
H-VCO
1. When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
2. H-FREE(1chip) is set to 1.
3. H-OUT is set by intelligent monitor output.
4. IM input is set as TIM input.
5. H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
6. When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
7. H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC
1. When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
2. AGC-OUT is set by intelligent monitor output.
3. IM input is set as AD input.
4. By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO
1. When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
2. VIF-DEF(1chip) is set to 1.
3. AFC is set by intelligent monitor output.
4. IM input is set as AD input.
5. VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
6. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
7. VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
MTS-FILTER
Adjustment is performed in the center of the range when FILTER status is OK.
1. If data is changed from 0 to 63, point where NG → OK is A and point where OK → NG is B.
2. If data is changed from 63 to 0, point where NG → OK is C and point where OK → NG is D.
3. (A+B+C+D)/4 is the adjustment point.
10
Page 11
Setting Mode Items
No. Item Name IC Register Range Default
F01 VideoTone-Gain (TV) 1chip V-TONE 0 / 1 0
F02 VideoTone-Gain (AV) 1chip V-TONE 0 / 1 0
F03 VideoTone-Gain(YUV) 1chip V-TONE 0 / 1 0
F04 ABCL 1chip ABCL 0 / 1 0
F05 BS 1chip BS-OFF 0 / 1 0
F06 ABCL-G 1chip ABCL-G 0 / 1 0
F07 SHP-AV OFFSET VIDEO-TONE(OFFSET) -16~+16 0
F08 SHP-YUV OFFSET VIDEO-TONE(OFFSET) -16~+16 0
F09 RGB-CLIP 1chip ExtRGB-Clip 0 / 1 0
F10 E-SAVE OFFSET CONTRAST(OFFSET) 0~63 30
F11 FAO-VOL 1chip A-ATT 0~127 120
F12 PIF-G 1chip VIF-GAIN 0~7 4
F13 Y-DELAY(TV) 1chip Y-Delay 0~7 0
F14 Y-DELAY(AV) 1chip Y-Delay 0~7 0
F15 Y-DELAY(YUV) 1chip Y-Delay 0~7 0
F16 TINT-AV OFFSET TINT(OFFSET) -32~+32 0
F17 COL-AV OFFSET COLOR(OFFSET) -32~+32 0
F18 R-DRI(R2) OFFSET R-DRI(OFFSET) -32~+32 0
F19 R-DRI(R) OFFSET R-DRI(OFFSET) -32~+32 0
F20 R-DRI(B) OFFSET R-DRI(OFFSET) -32 ~+32 0
F21 B-DRI(R2) OFFSET B-DRI(OFFSET) -32~+32 0
F22 B-DRI(R) OFFSET B-DRI(OFFSET) -32~+32 0
F23 B-DRI(B) OFFSET B-DRI(OFFSET) -32~+32 0
F24 V-FREE 1chip V-FREE 0 / 1 0
F25 GAMMA 1chip GAMMA 0~3 0
F26 TRAP(TV) 1chip TRAP-FINE 0~3 2
F27 TRAP(AV) 1chip TRAP-FINE 0~3 2
F28 H-FREE 1chip H-FREE 0 / 1 0
F29 1W(TV) 1chip V.Window 0 / 1 0
F30 1W(AV) 1chip V.Window 0 / 1 0
F31 YLPF 1chip YSW-LPF 0 / 1 1
F32 BS-D 1chip BS-DISCHARGE 0~3 0
F33 BS-C 1chip BS-CHARGE 0~3 0
F34 SL(TV) 1chip S-SLICE DOWN 0~3 0
F35 SL(AV) 1chip S-SLICE DOWN 0~3 0
F36 SL(YUV) 1chip S-SLICE DOWN 0~3 0
F37 AFC2 1chip AFC2-G 0 / 1 0
F38 VD(TV) 1chip Vsync-Det 0 / 1 0
F39 VD(AV) 1chip Vsync-Det 0 / 1 0
F40 AS(TV) 1chip Auto-Slice 0 / 1 0
F41 AS(AV) 1chip Auto-Slice 0 / 1 0
F42 AS(YUV) 1chip Auto-Slice 0 / 1 0
F43 FBP(TV) 1chip FBP Vth 0 / 1 0
F44 FBP(AV) 1chip FBP Vth 0 / 1 0
F45 FBP(YUV) 1chip FBP Vth 0 / 1 0
F46 C.Clip Level 1chip C.Clip Level 0 / 1 0
F47 PSW MTS PSW 0 / 1 0
F48 FAO-VOL MTS VOL 0~63 60
F49 CP PLL CP 0 / 1 0
F50 CC LEVEL MICRON 0
F51 OSD POS MICRON 0
F52 OFFSET-ADJ-COL 1 chip COLOR -32~32 0
F53 OFFSET-ADJ-TINT 1 chip TINT -32~32 0
F54 OFFSET-ADJ-TINT-YUV 1 chip BASEBAND-TINT -32~32 0
14U-FM1
CU14FM1
11
Page 12
14U-FM1
CU14FM1
Option Mode Items
No ITEM 0 1 DEFAULT
O01 DEM0 Without DEMO With DEMO 1
O02 DOWNLOAD Without V-CHIP OP With V-CHIP OP 1
O03 V -CHIP Without V-CHIP With V-CHIP 1
O04 SPEAKER Without SPEAKER With SPEAKER 1
O05 FAO Without FAO With FAO 1
O06 P.PREF Without P.PREF With P.PREF 1
O07 UNIV+ Without UNIV+ With INIV+ 1
O08 VIEW TIMER Without VIEW TIMER With VIEW TIMER 1
O09 EZ-SETUP EZ-SETUP AUTO PRESET 1
O10 PON-CH Without POWER-ON With POWER-ON 1
O11 FAV-COL FAV-COL COL-TEMP 1
O12 COMPONENT Without COMPONENT With COMPONENT 1
O13 AV Without AV With AV 1
O14 AV2 AV1 system AV2 system 1
O15 MTS Without MTS With MTS 1
O16 TONE-CTRL Without S-ADJ With S-ADJ 1
O17 AUTO-OFF Without AUTO-OFF With AUTO-OFF 1
O18 INIT-LANG ENGLISH SPANISH 0
O19 SETUP-FLAG NO SETUP AUTO SETUP 1
3: Display "FRONT A/V INPUTS" and
"REAR A/V INPUTS" in DEMO mode.
O20 FR.AV (Front, 2
Rear AV)
2: Display "FRONT A/V INPUTS" only in
DEMO mode.
1: Display "REAR A/V INPUTS" only in
DEMO mode.
0: No display of above lines in DEMO mode.
Check Mode
Micron mask version, software version and ROM correction function status are displayed in check mode.
12
Page 13
14U-FM1
CU14FM1
ADJUSTMENT METHOD
Caution: to get into the service mode, one of the ways is press direct key for service items. the other ways
is short the main chassis JA309 and JA402
There is three stage of Service Mode data
First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F51
to go into third stage of service mode data, press MENU key
Third stage data from 001 ~ 020
Below is the contents of these data
First Stage
Data Service Mode Function Range Default Data
V01 SUB-PICTURE CONTRAST 0~127 127
V02 SUB-TINT TINT 0~127 64
V03 SUB-COLOR COLOR 0~127 64
V04 SUB-BRIGHT BRIGHT 0~255 128
V05 SUB-SHARP VIDEO-TONE 0~63 32
V06 V-SHIFT V-SHIFT 0~7 7
V07 H-SHIFT H-PHASE 0~31 16
V08 RF-AGC RF-DELAY 0~127 127
V09 V-SIZE V-SIZE 0~63 32
V10 PIF-VCO VIF-VCO 0~63 32
V11 R-CUTOFF R-CUTOFF 0~255 64
V12 G-CUTOFF G-CUTOFF 0~255 64
V13 B-CUTOFF B-CUTOFF 0~255 64
V14 R-DRIVE R-DRIVE 0~127 64
V15 B-DRIVE B-DRIVE 0~127 64
V16 SUB-COLOR(YUV) COLOR 0~127 64
V17 SUB-TINT(YUV) BASEBAND-TINT 0~127 64
V18 CC-POS 0~255
V19 CUT OFF
V20 SUB-VOL A-ATT 0~127 127
V21 H-VCO H-VCO 0~7
M01 MTS-ATT ATT (MTS) 0~15 10
M02 MTS-VCO VCO (MTS) 0~63 32
M03 MTS-FILTER FILTER (MTS) 0~63 28
M04 MTS-WIDEBAND WIDEBAND (MTS) 0~63 27
M05 MTS-SPECTRAL SPECTRAL (MTS) 0~63 32
M06 SUB-VOL VOL (MTS) 0~63 63
Auto Adjustment Item
1. H-VCO (Currently need manual adj)
2. RF-AGC
3. PIF-VCO
4. MTS-FILTER
13
Page 14
14U-FM1
CU14FM1
Second Stage
Data Service Mode Function Range Default Data
F01 VIDEO TONE -GAIN (TV) V-TONE 0/1 0
F02 VIDEO TONE -GAIN (AV V-TONE 0/1 0
F03 VIDEO TONE -GAIN(YUV) V -T ONE 0/1 0
F04 ABCL ABCL 0/1 0
F05 BS BS-OFF 0/1 0
F06 ABCL-G ABCL-G 0/1 0
F07 SHP-AV VIDEO-TONE
F08 SHP-YUV VIDEO-TONE
F09 SHP-CLIP EXTRGB-CLIP 0/1 0
F10 E-SAVE CONTRAST(OFFSET) 0~63 30
F11 FAO-VOL A-ATT 0~127 120
F12 PIF-G VIF-GAIN 0~7 0
F13 Y-DELAY(TV) Y-DELAY 0~7 0
F14 Y-DELAY(AV) Y-DELAY 0~7 0
F15 Y-DELAY(YUV) Y-DELAY 0~7 0
F16 TINT-AV TINT(OFFSET) -32~+32 0
F17 COL-AV COLOR(OFFSET) -32~+32 0
F18 R-DRI(R2) R-DRI(OFFSET) -32~+32 0
F19 R-DRI( R) R-DRI(OFFSET) -32~+32 0
F20 R-DRI(B) R-DRI(OFFSET) -32~+32 0
F21 B-DRI(R2) B-DRI(OFFSET) -32~+32 0
F22 B-DRI( R) B-DRI(OFFSET) -32~+32 0
F23 B-DRI(B) B-DRI(OFFSET) -32~+32 0
F24 V-FREE V-FREE 0/1 0
F25 GAMMA GAMMA 0~3 0
F26 TRAP(TV) TRAP-FINE 0~3 2
F27 TRAP(AV) TRAP-FINE 0~3 2
F28 H-FREE H-FREE 0/1 0
F29 1W(TV) V.WINDOW 0/1 0
F30 1W(AV) V.WINDOW 0/1 0
F31 YLPF YSW-LPF 0/1 1
F32 BS-D BS-DISCHARGE 0~3 0
F33 BS-C BS-CHARGE 0~3 0
F34 SL(TV) S-SLICE DOWN 0~3 0
F35 SL(AV) S-SLICE DOWN 0~3 0
F36 SL(YUV) S-SLICE DOWN 0~3 0
F37 AFC2 AFC2-G 0/1 0
F38 VD(TV) VSYNC-DET 0/1 0
F39 VD(AV) VSYNC-DET 0/1 0
F40 AS(TV) AUTO-SLICE 0/1 0
F41 AS(AV) AUTO-SLICE 0/1 0
F42 AS(YUV) AUTO-SLICE 0/1 0
F43 FBP(TV) FBP VTH 0/1 0
F44 FBP(AV) FBP VTH 0/1 0
F45 FBP(YUV) FBP VTH 0/1 0
F46 C.CLIP LEVEL C.CLIP LEVEL 0/1 0
F47 PSW PSW 0/1 0
F48 FAO-VOL VOL 0~63 60
F49 CP CHARGE PUMP 0/1 0
F50 CC LEVEL
F51 OSD POS
F52 COL OFFSET (SUR → NOR) 0
F53 TINT OFFSET (SUR → NOR) 0
F54 TING-YUV TINT-YUV(OFFSET) 0
(OFFSET)
(OFFSET)
-16~+16 0
-16~+16 0
14
Page 15
Third Stage
Data Service Mode DATA="0" DATA="1" Default Data
001 DEMO DEMO OFF ON 1
002 DOWNLOAD V-CHIP OP OFF ON 1
003 V-CHIP V-CHIP OFF ON 1
004 SPEAKER SPEAKER OFF ON 1
005 FAO FAO OFF ON 1
006 P.PREF P.REF OFF ON 1
007 UNIV+ UNIV+ OFF ON 1
008 VIEW TIMER VIEW TIMER OFF ON 1
009 EZ-SETUP EZ-SETUP AUTO PRESET 1
010 PON-CH POWER-ON OFF 0N 1
011 FAV-COL FAV-COL COL-TEMP 1
012 COMPONENT COMPONENT OFF ON 1
013 AV AV OFF ON 1
014 AV2 AV2 OFF ON 1
015 MTS MTS OFF ON 1
016 TONE-CTRL S-ADJ OFF ON 1
017 AUTO-OFF AUTO-OFF OFF ON 1
018 INIT-LANG ENGLISH SPANISH 1
019 SETUP-FLAG NO SET UP AUTO SET UP 1
020 AV-FR
"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
3
14U-FM1
CU14FM1
15
Page 16
14U-FM1
CU14FM1
OPTION SET UP
REFER AS BELOW STEP RANGE REFER AS BELOW
–
ADJUSTMENT
ITEM
CONTROL
ADJUSTMENT
POSITION
–
–
PRE-ADJUST
CONTENT
REQUIREMENT
14UFM1
OSD CHECKING
INPUT
CONDITION
OUTPUT
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
V05 F13 F14 F16 F17 F30 F34 F38 F40 F49
SHARP Y-DL(TV) Y-DL(AV) TINT-AV COL-AV 1W(AV) SL(TV) VD(TV) AS(TV) CP
FUNCTION
14UFM1 50 5 2 8 4 1 1 1 1 1
16-2
F18 F19 F20 F21 F22 F23 F52 F53 F35 F41 F48
R-D(R2) R-D(R) R-D(B) B-D(R2) B-D(R) B-D(B) C-OF TI-OF SL(AV) AS(AV) FAO-VOL
DEF
CU14FM1 50 5 2 8 4 1 1 1 1 1
20U-FS1 50 5 2 8 4 1 1 1 1 1
CU20FS1 50 5 2 8 4 1 1 1 1 1
ADJUSTMENT
PROCEDURE
DATA SETUP FOR FIRST AND SECOND STAGE SERVICE DATA
FUNCTION
14UFM1 +8 +3 -2 -18 -8 +6 0 +8 1 1 60
CU14FM1 +8 +3 -2 -18 -8 +6 0 +8 1 1 60
20U-FS1 +8 +3 -2 -18 -8 +6 0 +8 1 1 58
CU20FS1 +8 +3 -2 -18 -8 +6 0 +8 1 1 58
DEF
OPTION SET UP
REFER AS BELOW STEP RANGE REFER AS BELOW
–
ADJUSTMENT
ITEM
CONTROL
ADJUSTMENT
POSITION
–
–
PRE-ADJUST
CONTENT
REQUIREMENT
14UFM1
OSD CHECKING
INPUT
CONDITION
OUTPUT
BUS OPTION FOR THIRD STAGE SERVICE DATA
001 002 003 004 005 006 007 008 009 010
DEMO DOWNLOAD V-CHIP SP FAO P.PREF UNIV+ VIEW EZ PON-CH
FUNCTION
14UFM1 1 1 1 0 0 0 0 1 0 0
16-1
011 012 013 014 015 016 017 018 019 020
BUS OPTION FOR THIRD STAGE SERVICE DATA
FAV-COL COMP AV AV2 MTS TONE AUTO LAN SETUP AV-FR
FUNCTION
14UFM1 1 0 1 0 0 0 0 0 1 3
CU14FM1 1 0 1 0 0 0 0 0 1 3
20U-FS1 1 1 1 1 1 1 0 0 1 3
CU20FS1 1 1 1 1 1 1 0 0 1 3
009 → “0”=EZ-SETUP “1”=AUTO PRESET
DEF “0”=DISABLE “1”=ENABLE
CU14FM1 1 0 0 0 0 0 0 1 0 0
20U-FS1 1 1 1 1 1 1 1 1 0 0
CU20FS1 1 0 0 1 1 1 1 1 0 0
ADJUSTMENT
PROCEDURE
018 → “0”=ENGLISH “1”=SPANISH
019 → “0”=NO SET UP “1”=AUTO SETUP
DEF 011 → ”0”=FAV-COL “1”=COL-TEMP
16
Page 17
H-POSITION
AB
V07 STEP RANGE 0-31
14U-FM1
CU14FM1
17-2
C BUS CONTROL
2
I
ADJUSTMENT
ITEM
+B ADJUSTMENT
CONTROL
ADJUSTMENT
POSITION
OPTION SET UP, BUS SET UP, CRT-PURITY
US 4 CH LION HEAD (MONOSCOPE)
AC 120V, US MAGNETIC FIELD
PRE-ADJUST
CONTENT
REQUIREMENT
INPUT
CONDITION
1. ADJUST THE V07 BUS DAT A T O HA VE A BALANCE POSITION TO SPEC
CONFIRMATION BY CRT SCREEN
OUTPUT
OF A=B.
B SLIDELY SMALLER THAN A
2. IF CANNOT MAKE IT T O A=B, ADJ FROM THE BEST POINT SO THAT
ADJUSTMENT
PROCEDURE
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
17-1
– STEP RANGE –
–
AFTER ALL ADJUSTMENT FINISHED.
US 4 CH LION HEAD (MONOSCOPE PATTERN)
AC 120V, RF INPUT
CONNECT THE DIGITAL VOLTMETER AND MEASURE
+B LINE
ADJUSTMENT
ITEM
CONTROL
ADJUSTMENT
POSITION
PRE-ADJUST
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
ADJUST R737 SO THAT THE +B VOLTAGE IN VOLTMETER READING IS
AS BELOW.
17
ADJUSTMENT
PROCEDURE
[VOLTAGE COMFIRMATION]
130 ± 0.5VDC (CHECKING SPEC : 130V ± 0.8 VDC)
Page 18
14U-FM1
CU14FM1
V-PHASE
18-2
V06 STEP RANGE 0-7
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
V-SIZE
C CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP, CRT-PURITY
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
REQUIREMENT
120V, RF INPUT, ZERO MAGNETIC FIELD
CONFIRMATION ON CRT SCREEN
INPUT
CONDITION
OUTPUT
ADJUST V06 BUS DATA TO HAVE MOST ACCEPTABLE VERTICAL PO-
SITION.
THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL
POSITION
NOTE: THE DATA FOR V06 LIMIT AT <= 04, EVEN POSITION GOOD
ENOUGH
ADJUSTMENT
PROCEDURE
[CHECKING CONFIRMATION]
18-1
V09 STEP RANGE 0~63
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
C CONTROL
2
OPTION SET UP, BUS SET UP, CRT PURITY, V-PHASE, +B ADJUST
I
CONTROL
PRE-ADJUST
REQUIREMENT
US 4 CH LION HEAD
AC 120V
CONFIRMATION BY CRT SCREEN
ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS
CONTENT
INPUT
CONDITION
OUTPUT
SPECIFIED BELOW.
CAUTION: - PLEASE AGING TV MORE THAN 10 MINUTES BEFORE
ADJUSTMENT.
18
ADJUSTMENT
PROCEDURE
[CHECKING SPEC]
OVERSCAN 10 ± 2.5%
Page 19
H-VCO
A
B
TEXT BOX BLK
14U-FM1
CU14FM1
19-2
V21 STEP RANGE 0-7
C CONTROL
2
I
OPTION SET UP, BUS SET UP
ADJUSTMENT
ITEM
CONTROL
ADJUSTMENT
POSITION
PRE-ADJUST
REQUIREMENT
CLOSED CAPTION SET UP
1) GO TO SERVICE MODE,
NO SIGNAL (RASTER) CONDITION
AC 120
IC 801 PIN 11
CONTENT
INPUT
CONDITION
OUTPUT
2) GO TO SERVICE DATA V21, ADJ UNTIL FREQ AS BELOW
ADJUSTMENT
PROCEDURE
[CHECKING SPEC]
FREQ = 15.735 ± 0.2 KHz
19-1
V18 STEP RANGE 0~255
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
C CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP
US 4 CH LION HEAD
AC 120V
CONTENT
REQUIREMENT
INPUT
CONFIRMATION ON CRT DISPLAY.
CONDITION
OUTPUT
SPEC OF A=B.
1) BY SELECTING THE V18, BOX BLK TEXT WILL BE APPEARED.
2) ADJUST THE V18 BUS DATA TO HAVE A BALANCE POSITION TO
ADJUSTMENT
PROCEDURE
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
19
Page 20
14U-FM1
CU14FM1
RF-AGC
20-2
V08 STEP RANGE 0-127
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
PIF-VCO
C CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP
US10CH HALF COLOR BAR
RF INPUT
FIELD STRENGTH 56dBµV (FIX)
TUNER AGC TERMINAL (TP 201) OR CRT DISPLAY CONFIRMATION
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
KEY AND CONFIRM THE OK DISPLAY ON THE SCREEN.
(AT SELF ADJUSTMENT MODE)
1. GO TO SERVICE MODE
2. GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC
3. IF APPEAR NG PLS REPEAT STEP 2 AGAIN.
COME MAXIMUM, THEN DROP 0.1V BELOW MAXIMUM VOLTAGE.
(AT MANUAL ADJUSTMENT MODE)
1. ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BE-
SURE THERE IS NO NOISE
THAT THERE IS NO CROSS MODULATION BEAT.
2. CHANGE THE ANTENNA INPUT SIGNAL T O 63-67 dBµV, AND MAKE
3. CHANGE THE ANTENNA INPUT SIGNAL T O 90-95 dBµV T O BE SURE
ADJUSTMENT
PROCEDURE
[CHECKING SPEC]
MAX - 0.1V dc
20-1
V10 STEP RANGE 0~63
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
C CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP
NO SIGNAL (RASTER) CONDITION
AC 120V
CONFIRMATION ON CRT DISPLAY (AUTO), IC801 PIN 2 VOLTAGE (MANUAL).
(AT SELF ADJUSTMENT MODE)
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
SCREEN
2) PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR “OK” AT
AS SPECIFIED BELOW
3) IF APPEAR “NG” PLS REPEAT STEP2
(AT MANUAL ADJUSTMENT MODE)
1) GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V10
2) ADJUST THE DAT A UP/DO WN UNTIL IC801 PIN 2 V OLT AGE BECOME
20
ADJUSTMENT
PROCEDURE
[CHECKING SPEC]
2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5V)
Page 21
14U-FM1
BLACK
US14
WHITE
CU14FM1
WHITE BALANCE
V14,V15,V11,V12,V13 STEP RANGE 0-127, 0~255
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
C BUS CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP, SCREEN
23CH 501RE WINDOW PATTERN
CONTENT
REQUIREMENT
120V
CRT SCREEN DISPLAY.
INPUT
CONDITION
OUTPUT
ATTACH), ADJ V04 UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN
LET THE GUN POINT AT WHITE POSITION (AS DRAWING ATTACH),
ADJUST V01 UNTIL BRIGHTNESS Y BECOME 150 cd/m2, ADJUST
FIRST LET THE GUM POINT AT BLACK POSITION (AS DRAWING
THE BUS DATA OF V14 (R DRIVE), V15(B DRIVE) UNTIL THE AXIS
1) WHITE (HIGH BEAM)
OF COLOR TEMPERATURE BECOME X=0.273, Y=0.280
2) BLACK (LOW BEAM)
AW AY FROM THE D AT A ADJUSTED IN STEP 1), ADJUST A GAIN THE
TWO SERVICE DATA WHICH HAVE CHOSEN AT SCREEN ADJUST
LET THE GUN POINT AT BLACK POSITION, IF THE V ALUE SHIFTED
SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE.
ADJUSTMENT
PROCEDURE
THIS ADJUSTMENT.
*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING
**REPEAT STEP 1), 2) TO GET A REGULATED POSITION.
°K + 1 MPCD)
[CHECKING CONFIRMATION]
X=0.273, Y=0.280 (11,600
21-2
SCREEN
ADJUSTMENT
V11,V12,V13 STEP RANGE 0-255
ITEM
ADJUSTMENT
POSITION
C CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP
WINDOW PATTERN OR US4CH LION HEAD
120V
CONFIRMATION ON CRT DISPLAY
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
64, GET IN Y-MUTE BY R/C AND SET V19 TO “1”, PICTURE APPEAR
IN CUT-OFF CONDITION
BRIGHT , THEN JUDGE THAT WHETHER THE CUT-OFF LINE APPEAR
1) IN SERVICE MODE, SET V04&V11&V12&V13 TO 127; V14&V15 TO
2) ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW
IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION V11=R-
CUTOFF, V12=G-CUTOFF, V13=B-CUTOFF, FIX THE DATA OF THE
21
COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE
OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE COLOR BE-
COME WHITE.
APPEAR AND USE R/C TO SET V19 TO “0”, NEXT DISABLE THE Y-
MUTE SO THAT PICTURE APPEAR IN NORMAL MODE.
3) TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DIS-
ADJUSTMENT
PROCEDURE
21-1
[VOLTAGE CONFIRMATION]
Page 22
14U-FM1
BLACK
US14
US14
WHITE
CU14FM1
SUB-PICTURE
V01 STEP RANGE 0-127
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
C BUS CONTROL
2
I
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS
WINDOW PATTERN
120V
CRT SCREEN DISPLAY.
CONTROL
PRE-ADJUST
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
ADJUST V01 BUS DATA UNTIL BRIGHTNESS Y=180 cd/m2.
1) LET THE GUN POINT AT WHITE POSITION (AS ATT ACH DRAWING),
NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN’T MATCH
THE SPEC
ADJUSTMENT
PROCEDURE
[VOLTAGER CONFIRMATION]
BRIGHTNESS Y=180 cd/m2
22-2
SUB-BRIGHT
V04 STEP RANGE 0-255
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
C CONTROL
2
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
I
CONTROL
PRE-ADJUST
REQUIREMENT
WINDOW PATTERN
120V
CONTENT
INPUT
CONDITION
CRT SCREEN DISPLAY.
1) LET THE GUN POINT AT BLACK POSITION (AS A TTACH DRAWING),
OUTPUT
ADJUST V04 BUS DATA UNTIL BRIGHTNESS Y=0.5 cd/m2, THEN
STEP DOWN MORE 4 STEP
22
ADJUSTMENT
PROCEDURE
[VOLTAGE CONFIRMATION]
BRIGHTNESS Y=0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
22-1
Page 23
SUB-COLOR
100% WHITE
WY RBMg
Cy G
V03 STEP RANGE 0-127
14U-FM1
CU14FM1
23-2
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
SUB-TINT
C BUS CONTROL
2
I
CONTROL
PRE-ADJUST
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TINT
US 10 CH HALF COLOR BAR PATTERN
CONTENT
REQUIREMENT
120V
R-AMP TR BASE (TP854)
CONFIRRM WITH OSCILLOSCOPE
INPUT
CONDITION
OUTPUT
OF COLOR BAR BEAT AT THE SAME LEVEL
1) SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW
2) THIS W AVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS
3) AFTER THAT PLS STEP UP 10 STEP DT AT V03.
ADJUSTMENT
PROCEDURE
B-AMP BASE (TP851)
MUST BE IN STEPPING
LEVEL
[CHECKING CONFIRMATION]
23-1
V02 STEP RANGE 0-127
C CONTROL
2
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
I
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
US 10 CH HALF COLOR BAR PATTERN
PRE-ADJUST
CONTENT
REQUIREMENT
120V
B-AMP TR BASE (TP851)
CONFIRRM WITH OSCILLOSCOPE
INPUT
CONDITION
OUTPUT
1) GET IN Y-MUTE FUNCTION BY R/C.
2) ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.
3) DISABLE THE Y -MUTE
**PLS TAKE NOTE THAT SERVICE MODE DATA F53 NEED TO SET +8
ADJUSTMENT
PROCEDURE
[CONFIRMATION]
23
Page 24
14U-FM1
CU14FM1
HIGH VOL T A GE
– STEP RANGE –
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
–
CONTROL
PRE-ADJUST
AFTER ALL ADJUSTMENT FINISHED.
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
REQUIREMENT
AC 130V, RF INPUT
R-AMP TR BASE (TP854)
CONFIRRM WITH OSCILLOSCOPE
INPUT
CONDITION
OUTPUT
SET THE USER CONTROL TO SHIPMENT SETTING POSITION. PUSH
ON Y-MUTE BY R/C CONFIRM THE V OLTAGE OF CRT ANODE BY HIGH
VOLTAGE METER AND MAKE SURE THE READING IS AS BELOW.
HIGH VOL T A GE
BELOW 28kV
ADJUSTMENT
PROCEDURE
[CAUTION POINT]
USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL/
DHHS STANDARD TO MAKE CORRECTION AND CONTROL.
24-2
X-RAY PROTECTION OPERATING CONFIRMATION
– STEP RANGE –
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
–
PRE-ADJUST
CONTROL
AFTER ALL ADJUSTMENT FINISHED.
US 4 CH LION HEAD (MONOSCOPE PATTERN)
CONTENT
REQUIREMENT
AC 120V, RF INPUT
CONFIRMATION BY THE CRT
INPUT
CONDITION
OUTPUT
SET THE USER CONTROL TO SHIPMENT POSITION.
[VOLTAGE CONFIRMATION]
CHECK THE VOLTAGE OF P603 PIN 3 AS SPECIFIED BELOW.
[OPERATION CONFIRMATION]
SUPPLY THE DC VOLTAGE TO P603 PIN 3 AND MAKE SURE THE PRO-
TECTOR IS FUNCTIONED.
HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.
[RECOVER INFORMATION]
PULL OUT THE AC CORD.
[CAUTION]
FROM THE RECOVER CONFIRMATION MENTIONED ABOVE, THE AC
ADJUSTMENT
PROCEDURE
24
TP VOLTA GE OPERATION VOL TAGE
21.0 ± 1.3V DC 27.0V
CODE MUST BE PULLED OUT AT LEAST 4 SECOND BEFORE PLUG-
GING IN AGAIN.(IN ORDER TO MAKE SURE THE µ-COM HAS BEEN
RESET.)
[VOLTAGE CONFIRMATION]
24-1
Page 25
TRI-VISION
– STEP RANGE –
14U-FM1
CU14FM1
25-2
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
V-CHIP
–
CONTROL
PRE-ADJUST
RATIING AND NAME.
(DOWNLOADING CONFIRMATION)
1) RECEIVE THE DOWNLOAD A SIGNAL.
2) SELECT V-CHIP CONTROL MENU THEN ON THE DOWNLOAD.
3) UNPLUG THE AC THEN PLUG AGAIN.
AFTER ALL ADJUSTMENT FINISHED.
RATING SYS. DOWNLOAD SIGNAL A/B (PRCC SIG) INCLUDED SIGNAL.
AC 120V, RF INPUT
CONFIRMATION BY CRT SCREEN
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
4) BACK TO V-CHIP CONTROL MENU, CHECK THE DOWNLOADED
(DOWNLOADING CONFIRMATION)
1) RECEIVE THE DOWNLOAD B SIGNAL.
2) UNPLUG THE AC CORD AND PLUG IT AGAIN.
RATING AND NAME.
3) BACK TO V-CHIP CONTROL MENU, CHECK THE DOWNLOADED
ADJUSTMENT
PROCEDURE
group sample.
~ Do check one sample that been picked up for presenting the specified
[COMFIRMATION]
25-1
– STEP RANGE –
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
–
CONTROL
PRE-ADJUST
AFTER ALL ADJUSTMENT FINISHED.
UHF 15 CH (V-CHIP TRANSMISION SIGNAL CH)
AC 120V, RF INPUT
CONFIRMATION BY THE CRT
CONTENT
REQUIREMENT
INPUT
CONDITION
OUTPUT
1) RECEIVE THE UHF 15 CH.
2) PUSH THE DISPLAY KEY (R/C), MAKE SURE THA T THE OSD
V-CHIP RATING DISPLAY IS EQUAVALENCE TO TRANSMISSION
RATING.
25
ADJUSTMENT
PROCEDURE
[VOLTAGE CONFIRMATION]
Page 26
14U-FM1
CU14FM1
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
654321
26
Page 27
BLOCK DIAGRAM-1
H
G
F
14U-FM1
CU14FM1
E
D
C
B
A
654321
27
Page 28
14U-FM1
CU14FM1
MODEL 14U-FM1 BLOCK DIAGRAM-2
H
G
F
E
D
C
B
A
87109654321
28
Page 29
14U-FM1
CU14FM1
29
1716 1918151413121110
Page 30
14U-FM1
CU14FM1
MODEL CU14FM1 BLOCK DIAGRAM-2
H
G
F
E
D
C
B
A
87109654321
30
Page 31
14U-FM1
CU14FM1
31
1716 1918151413121110
Page 32
14U-FM1
CU14FM1
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5. indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set f or normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
WAVEFORMS
1.024 Vp-p
1
2
5.69 Vp-p
3
5.69 Vp-p
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, g reen and b lue cathodes of
the picture tube depend on the tint, color level and
picture control.
2. indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
å
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
ç
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES åET HACHRES ( ):
PIECES RELATIVES A LA SECURITE.
MARQUE ç : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
4
5.84 Vp-p
5
2.00 Vp-p
6
2.08 Vp-p
Horiz.Rate
6.56 Vp-p
7
Horiz.Rate
3.8 Vp-p
e
Vert.Rate
94.4 Vp-p
o
Horiz.Rate
6.40 Vp-p
8
Horiz.Rate
118 Vp-p
r
Horiz.Rate
109.6 Vp-p
p
Horiz.Rate
4.88 Vp-p
9
Horiz.Rate
440 Vp-p
t
Horiz.Rate
Horiz.Rate
158 Vp-p
0
Horiz.Rate
5.04 Vp-p
y
Horiz.Rate
Vert.Rate
1140 Vp-p
q
Horiz.Rate
5.12 Vp-p
u
Vert.Rate
Vert.Rate
48 Vp-p
w
Vert.Rate
112.8 Vp-p
i
Horiz.Rate
Horiz.Rate
Horiz.Rate
32
Page 33
SCHEMATIC DIAGRAM: CRT Unit
H
G
F
14U-FM1
CU14FM1
E
D
C
B
A
654321
33
Page 34
14U-FM1
CU14FM1
MODEL 14U-FM1 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
87109654321
34
Page 35
14U-FM1
CU14FM1
35
1716 1918151413121110
Page 36
14U-FM1
CU14FM1
MODEL CU14FM1 SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
E
D
C
B
A
87109654321
36
Page 37
14U-FM1
CU14FM1
37
1716 1918151413121110
Page 38
14U-FM1
CU14FM1
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
654321
38
Page 39
14U-FM1
CU14FM1
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Chip Parts Side)
A
654321
39
Page 40
14U-FM1
CU14FM1
H
G
F
PWB-B: CRT Unit (Wiring Side)
E
D
C
B
A
654321
40
PWB-B: CRT Unit (Chip Parts Side)
Page 41
14U-FM1
CU14FM1
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are
identified by å and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create
shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER 2. REF. NO.
3. PART NO. 4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free; 1800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
' MARK: X-RAY RELATED PARTS
Ref. No. Part No. ★ Description Code
PICTURE TUBE
'åV101 VB36QDT351X~S J Picture Tube CC
'åDY601 RCiLHA019WJZZ R Deflection Yok e BD
or
RCiLHA033WJZZ
å L706 RCiLG0089PEZZ R Degaussing Coil AM
LHLDW0003PEKZ R Wire Holder, x4 AB
LHLDW0016PEKZ R Holder, x3 AB
PMAGF3046CEZZ J Purity Magnet AF
PSPAG0003PEZZ R Spacer, x3 AD
QEARCA011WJZZ R Grounding Starp AF
LISTE DES PIECES
CHANGE DES PIECES
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp
éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces
élelectriques qui pr élesentent ces particular it éles, sont rep éler élee
par la marque å et sont hachur élees dans les listes de pi`eces et dans
les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente
pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece
recommand élee parl'usine et dans ce manuel de service, peut provoquer
une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE 2. NO. DE REF
3. NO. DE PIECE 4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
★ MARQUE: SECTION LIVRAISON DES PIECES DERECHANGE
' MARQUE: PIECES RELATIVE AUX RAYONS X
Ref. No. Part No. ★ Description Code
PWB-A: DUNTKB177WEA0(14U-FM1)
PWB-A: DUNTKA177WEA1(CU14FM1)
MAIN UNIT
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU201 RTUNQA003WJZZ R Tuner AY
INTEGRATED CIRCUITS
IC301 VHiAN7523++-1 J AN7523 AH
å IC501 VHiTDA9302H-1 J TDA9302H AH
IC601 VHiKA7809AP-1 J KA7809API AE
å IC701 VHiTEA1507/-1 J TEA1507P/N1 AL
å IC702 RH-FX0008GEZZ J PC123FY8 AE
IC801 VHiM61250AF1EQ R I.C. AU
IC1001 RH-iXA155WJZZ R I.C. AV
IC1005 VHiM24C04W/-1 J M24C04-WBN6 (CU14FM1) AG
IC1005 VHiM24C16B/-1 J M24C16-BN6 (14U-FM1) AG
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
14U-FM1
PWB-A DUNTKB177WEA0 – MAIN Unit —
PWB-B DUNTKB178WEA0 – CRT Unit —
CU14FM1
PWB-A DUNTKB177WEA1 – MAIN Unit —
PWB-B DUNTKB178WEA1 – CRT Unit —
Q201 VS2SC2735//1E J 2SC2735 AC
TRANSISTORS
Q302 VS2PD601AR/-1 J 2PD601AR AB
or
VS2SC3928AR-1
Q601 VS2SC2482//-1 J 2SC2482 AD
Q602 VS2SD2586//1E J 2SD2586 AM
Q603 VS2PC1815G+-1 2PC1815G
or
VS2SC3198-G1E
Q604 VS2PD601AR/-1 J 2PD601AR AB
or
VS2SC3928AR-1
å Q701 VSSPA04N60C-1 R SPA04N60C AK
or
VS2ST4NC60FP
Q702 VS2PC1815Y+-1+ R 2PC1815Y AC
or
VS2SC3198-Y1E
Q703 VS2PC1815Y+-1+ R 2PC1815Y AC
or
VS2SC3198-Y1E
Q751 VS2SC2236Y/-1 J 2SC2236Y AD
Q752 VS2SC2236Y/-1 J 2SC2236Y AD
Q753 VS2PC1815G+-1+ R 2PC1815G AC
41
Page 42
14U-FM1
CU14FM1
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A: DUNTKB177WEA0(14U-FM1)
PWB-A: DUNTKB177WEA1(CU14FM1)
MAIN UNIT (Continued)
or
VS2SC319S-G1E
Q755 VS2PD601AR/-1 J 2PD601AR AB
or
VS2SC3928AQ-1
Q804 VS2PB709AR/-1 J 2PB709AR AB
or
VS2SA1530AQ-1
DIODES
D201 RH-EX0676GEZZ J Zener Diode, 33V AA
D203 RH-DX0048GEZZ J Diode AA
D391 RH-DX0302CEZZ J Diode AC
D501 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D502 RH-EX0652GEZZ J Zener Diode, 18V AB
D503 RH-EX0612GEZZ J Zener Diode, 5.1V AA
D505 RH-DX0441CEZZ J Diode AC
D510 RH-DX0131CEZZ J Diode AC
D511 RH-DX0048GEZZ J Diode AA
D512 RH-DX0048GEZZ J Diode AA
D601 RH-DX0048GEZZ J Diode AA
D602 VHD1SS244//-1 J Diode AB
D603 RH-EX0666GEZZ J Zener Diode, 24V AB
å D606 RH-DX0131CEZZ J Diode AC
D608 RH-DX0131CEZZ J Diode AC
or
RH-DX0302CEZZ
å D701 RH-DX0111PEZZ R Diode AG
D708 RH-DX0048GEZZ J Diode AA
or
VHD1SS244//-1
D710 RH-DX0048GEZZ J Diode AA
D717 RH-EX0616GEZZ J Zener Diode, 5.6V AA
D751 RH-DX0229CEZZ J Diode AF
D752 RH-DX0131CEZZ J Diode AC
D755 RH-DX0048GEZZ J Diode AA
D756 RH-DX0441CEZZ J Diode AC
D801 RH-EX0613GEZZ J Zener Diode, 5.1V AA
D806 RH-DX0048GEZZ J Diode AA
D807 RH-EX0625GEZZ J Zener Diode, 8V AA
D808 RH-DX0048GEZZ J Diode AA
D810 RH-EX0867CEZZ J Zener Diode, 8.1V AC
D811 RH-EX0867CEZZ J Zener Diode, 8.1V AC
D812 RH-EX0867CEZZ J Zener Diode, 8.1V AC
D813 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D815 RH-EX0263TAZZ J Zener Diode AB
D1004 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D1081 RH-DX0048GEZZ J Diode AA
D1085 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D1086 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D1087 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D1088 RH-EX1393CEZZ J Zener Diode, 5.1V AB
D1089 RH-EX0613GEZZ J Zener Diode, 5.1V AA
D1090 RH-EX1393CEZZ J Zener Diode, 5.1V AB
VA701 RH-VX0019CEZZ J Varistor AC
or
RH-VX0074CEZZ
or
RH-VX0026CEZZ
or
RH-VX0048CEZZ
or
RH-VX0035CEZZ
PACKAGED CIRCUITS
å PR702 RMPTP0026CEZZ J Packaged Circuit AF
or
RMPTP0092CEZZ
or
RMPTP0072CEZZ
X801 RCRSAA009WJZZ R Crystal AF
CF201 RFiLC0447CEZZ J Ceramic Filter AD
FILTERS AND COILS
CF802 RFiLC0446CEZZ J Ceramic Filter AD
SF201 RFiLC0405CEZZ J SAW Filter AH
L202 VP-CF270K0000 J Peaking 27µH AB
L203 VP-DF270K0000 J Peaking 27µH AB
L204 VP-XF1R2K0000 J Peaking 1.2µH AB
L602 RCiLP0223CEZZ J Coil AE
å L603 RCiLZA006WJZZ R Coil AH
å L701 RCiLF0078PEZZ R Coil AF
å L703 RCiLF0078PEZZ R Coil (CU14FM1) AF
L751 RCiLP0225CEZZ J Coil AF
L801 VP-DF100K0000 J Peaking 10µH AB
L802 VP-DF100K0000 J Peaking 10µH AB
L803 VP-DF100K0000 J Peaking 10µH AB
L804 VP-XF150K0000 J Peaking 15µH AB
L806 VP-DF100K0000 J Peaking 10µH AB
L807 VP-XF1R2K0000 J Peaking 1.2µH AB
TRANSFORMERS
'åT602 RTRNF A011WJZZ R H-Volt Transf ormer AN
å T603 RTRNZ0144PEZZ R Transformer AE
å T701 RTRNWA018WJZZ R Transformer AK
CONTROL
R737 RVR-M4588CEZZ+ R 22k(B) 130V Adj. AC
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
C201 VCEA0A1CW476M J 47 16V EL. AB
C202 VCEA0A0JW477M J 470 6.3V EL. AC
C203 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C204 VCEA0A0JW477M J 470 6.3V EL. AC
C205 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C206 VCEA0A1HW106M J 10 50V EL. AB
C207 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C208 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C209 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C210 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C211 VRS-CY1JF000J J 0 1/16W M-Ox. AA
C213 VCKYCY1HB102K J 1000p 50V Ceramic AA
C301 VCEA0A1CW477M J 470 16V EL. AC
C304 VCEA0A1CW106M J 10 16V EL. AB
C310 VCEA0A1HW225M J 2.2 50V EL. AB
C311 VCEA0A1HW474M J 0.47 50V EL. AB
C312 VCEA0A1HW474M J 0.47 50V EL. AB
C313 VCKYCY1CB333K J 0.033 16V Ceramic AA
C322 VCEA0A1HW105M J 1.0 50V EL. AB
C392 VCQYTA1HM103J J 0.01 50V Mylar AA
C393 VCEA0A1CW108M J 1000 16V EL. AD
C505 VCEA0A1HW107M J 100 50V EL. AB
C508 VCEA0A2AW105M J 1.0 100V EL. AB
C511 VCEA0A1VW477M J 470 35V EL. AB
C512 VCKYPA2HB102K J 1000p 500V Ceramic AA
C513 VCEA0A1VW108M J 1000 35V EL. AD
C514 VCFYSA1JB563J+ R 0.056 63V Mylar AD
C515 VCEACA1HC335J J 3.3 50V EL. AC
C516 VCEA0A2AW105M J 1.0 100V EL. AB
C518 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C519 VCKYCY1HB102K J 1000p 50V Ceramic AA
C601 VCQYTA1HM563J J 0.056 50V Mylar AB
C602 VCEA0A1HW475M J 4.7 50V EL. AB
C603 VCEA0A1HW105M J 1.0 50V EL. AB
C604 VCEA0A2EW106M J 10 250V EL. AD
C605 VCKYPA2HB102K J 1000p 500V Ceramic AA
C606 VCKYPA2HB102K J 1000p 500V Ceramic AA
'åC607 VCFPVC3ZA702H R 7000p 1.8kV M-Poly. AD
or (14U-FM1)
VCFPVC3CA702H
C608 VCKYPA2HB561K J 560p 500V Ceramic AA
C610 VCFYSB2EB823J J 0.082 250V Mylar AD
C611 VCFPVC2DB224J J 0.22 200V M-Poly. AE
C641 VCEA0A1EW108M J 1000 25V EL. AD
C642 VCEA0A1EW476M J 47 25V EL. AB
C643 VCEA0A1CW477M J 470 16V EL. AC
42
Page 43
14U-FM1
CU14FM1
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A: DUNTKB177WEA0(14U-FM1)
PWB-A: DUNTKB177WEA1(CU14FM1)
MAIN UNIT (Continued)
å C701 RC-FZ037SCEZZ J 0.22
or
RC-FZ012SGEZZ
or
RC-FZ017SCEZZ
or
RC-FZ029SCEZZ
C702 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
C703 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
å C705 RC-EZ1022CEZZ J 470 200V EL. AK
C706 VCQYTA1HM103J J 0.01 50V Mylar AA
å C711 VCFYFA1HA334J J 0.33 50V Mylar AB
C718 VCKYPA2HB472K J 4700p 500V Ceramic AB
C735 VCKYCY1HB681K J 680p 50V Ceramic AA
C737 VCEA0A1EW226M J 22 25V EL. AB
C738 RC-KZ0040CEZZ J 820p 2kV Ceramic AD
or
RC-KZ0340CEZZ
C739 VCEA0A1HW104M J 0.1 50V EL. AB
C743 VCKYPH3DB561K J 560p 2kV Ceramic AC
C751 RC-KZ0106GEZZ J 3300p
or
RC-KZ0092GEZZ
or
RC-KZ021SCEZZ
C752 VCKYPH3DB561K J 560p 2kV Ceramic AC
C753 RC-EZ0724CEZZ J 100 160V EL. AG
C754 RC-EZ0638CEZZ J 33 160V EL. AG
C755 VCQYTA1HM103J J 0.01 50V Mylar AA
C756 VCEA0A1EW108M J 1000 25V EL. AD
C758 VCEA0A1HW225M J 2.2 50V EL. AB
C759 VCKYPA1HB102K J 1000p 50V Ceramic AA
C784 VCKYCY1HB103K J 0.01 50V Ceramic AA
C801 VCFYFA1HA105J J 1.0 50V Mylar AE
C802 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C803 VCEA0A1AW476M J 47 10V EL. AB
C804 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C805 VCEA0A1HW105M J 1.0 50V EL. AB
C806 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C807 VCEA0A1CW337M J 330 16V EL. AC
C808 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C809 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C810 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C811 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C812 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C813 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C814 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C815 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C816 VCKYCY1EF104Z J 0.1 25V Ceramic AA
C817 VCEA0A1AW107M J 100 10V EL. AB
C818 VCEA0A1HW475M J 4.7 50V EL. AB
C819 VCCCCY1HH121J J 120p 50V Ceramic AA
C820 VCEA0A1HW474M J 0.47 50V EL. AB
C821 VCKYCY1HF153Z J 0.015 50V Ceramic AB
C822 VCEA0A1HW105M J 1.0 50V EL. AB
C823 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C824 VCEA0A1AW476M J 47 10V EL. AB
C825 VCEA9M1HW105M J 1.0 50V EL. AB
C826 VCKYPA1HF103Z J 0.01 50V Ceramic AA
C827 VCEA9M1CW476M J 47 16V EL. AB
C828 VCKYPA1HB103K J 0.01 50V Ceramic AA
C829 VCEA0A1CW476M J 47 16V EL. AB
C830 VCKYCY1CF224Z J 0.22 16V Ceramic AA
C832 VCKYCY1CF224Z J 0.22 16V Ceramic AA
C834 VCEA0A1CW107M J 100 16V EL. AC
C835 VCEA0A1CW106M J 10 16V EL. AB
C836 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C837 VCEA0A1HW105M J 1.0 50V EL. AB
C838 VCEA0A1CW106M J 10 16V EL. AB
C839 VCKYCY1HB332K J 3300p 50V Ceramic AA
C840 VCKYCY1EF104Z J 0.1 25V Ceramic AA
AC250V
Plastic AD
AC250V
Ceramic AG
C841 VCCCCY1HH101J J 100p 50V Ceramic AA
C842 VCEA9M1HW474M J 0.47 50V EL. AB
C843 VCEA9M1HW105M J 1.0 50V EL. AB
C845 VCKYCY1CF224Z J 0.22 16V Ceramic AA
C846 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C847 VCCCCY1HH220J J 22p 50V Ceramic AA
C848 VCEA0A1HW105M J 1.0 50V EL. AB
C849 VCFYFA1HA223J J 0.022 50V Mylar AB
C855 VCKYCY1HB561K J 560p 50V Ceramic AA
C856 VCKYPA1HB102K J 1000p 50V Ceramic AA
C1001 VCEA0A0JW107M J 100 6.3V EL. AB
C1003 VCEA0A1CW106M J 10 16V EL. AB
C1004 VCKYCY1CF474Z J 0.47 16V Ceramic AB
C1007 VCEA0A1CW107M J 100 16V EL. AC
C1008 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C1009 VCKYCY1HF103Z J 0.01 50V Ceramic AA
C1011 VCKYCY1HB221K J 220p 50V Ceramic AA
C1012 VCEA0A1HW105M J 1.0 50V EL. AB
C1013 VCKYCY1HB102K J 1000p 50V Ceramic AA
C1014 VCEA0A1HW475M J 4.7 50V EL. AB
C1015 VCCCCY1HH101J J 100p 50V Ceramic AA
C1081 VCEA0A1HW104M J 0.1 50V EL. AB
RESISTORS
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
RJ1 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ6 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ7 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ9 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ11 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ17 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ19 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ22 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ23 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ27 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ28 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ29 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ33 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ35 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ37 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ39 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ41 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ42 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ43 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ44 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ48 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ50 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ51 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ52 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ61 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ62 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ63 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ64 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ65 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ67 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ68 VRS-CY1JF000J J 0 1/16W M-Ox. AA
RJ69 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R201 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R202 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R205 VRS-CY1JF680J J 68 1/16W M-Ox. AA
R206 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA
R207 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R208 VRS-CY1JF331J J 330 1/16W M-Ox. AA
R209 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA
R216 VRS-VV3LB333J J 33k 3W M-Ox. AB
R220 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R301 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R302 VRN-VV3DBR22J J 0.22 2W M-Film AB
R303 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R304 VRD-RA2BE683J J 68k 1/8W Carbon AA
R305 VRS-CY1JF274J J 270k 1/16W M-Ox. AA
R310 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
R311 VRD-RA2BE272J J 2.7k 1/8W Carbon AA
R313 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R314 VRS-CY1JF000J J 0 1/16W M-Ox. AA
43
Page 44
14U-FM1
CU14FM1
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A: DUNTKB177WEA0(14U-FM1)
PWB-A: DUNTKB177WEA1(CU14FM1)
MAIN UNIT (Continued)
R315 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R364 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R383 VRS-CY1JF564J J 560k 1/16W M-Ox. AA
R384 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R431 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R432 VRS-CY1JF750J J 75 1/16W M-Ox. AA
R502 VRS-VV3AB561J J 560 1W M-Ox. AA
R503 VRN-VV3DB1R5J J 1.5 2W M-Film AB
R504 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R506 VRS-VV3AB331J J 330 1W M-Ox. AA
R507 VRN-VV3AB1R0J J 1.0 1W M-Film AA
R513 VRD-RM2HD273J J 27k 1/2W Carbon AA
R514 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R517 VRS-CY1JF123J J 12k 1/16W M-Ox. AA
R518 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R520 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R522 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R523 VRD-RA2BE101J J 100 1/8W Carbon AB
R524 VRD-RA2BE103J J 10k 1/8W Carbon AA
R525 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R526 VRD-RA2BE101J J 100 1/8W Carbon AB
å R601 VRS-SV2HC102J J 1.0k 1/2W M-Ox. AA
R602 VRD-RA2BE393J J 39k 1/8W Carbon AA
R603 VRD-RA2BE273J J 27k 1/8W Carbon AA
R604 VRD-RA2BE473J J 47k 1/8W Carbon AA
R605 VRD-RM2HD104J J 100k 1/2W Carbon AA
R606 VRN-VV3DBR27J J 0.27 2W M-Film AB
å R611 VRN-VV3AB1R8J J 1.8 1W M-Film AA
å R612 VRD-RM2HD270J J 27 1/2W Carbon AA
R613 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R614 VRD-RA2BE154J J 150k 1/8W Carbon AA
R615 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R616 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R617 VRS-CY1JF123J J 12k 1/16W M-Ox. AA
R618 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
å R621 VRN-SV2HC2R2J J 2.2 1/2W M-Film AB
R622 VRS-VV3DB682J J 6.8k 2W M-Ox. AA
R623 VRN-VV3ABR47J J 0.47 1W M-Film AA
R625 VRN-VV3ABR47J J 0.47 1W M-Film AA
R631 VRS-VV3LB391J J 390 3W M-Ox. AB
R632 VRS-VV3LB122J J 1.2k 3W M-Ox. AB
å R633 VRS-KA3HG3R3K J 3.3 5W M-Ox. AD
R635 VRS-VV3LB123J J 12k 3W M-Ox. AB
R636 VRS-VV3LB123J J 12k 3W M-Ox. AB
R637 VRD-RA2BE331J J 330 1/8W Carbon AA
R638 VRD-RA2BE331J J 330 1/8W Carbon AA
R639 VRS-VV3AB562J J 5.6k 1W M-Ox. AA
R661 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R662 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R701 VRW-KQ3HC1R5K J 1.5 5W Cement AE
R702 VRD-RM2HD100J J 10 1/2W Carbon AA
R705 VRN-VV3DBR39J J 0.39 2W M-Film AA
R706 VRN-VV3DBR39J J 0.39 2W M-Film AA
R707 VRS-SV2HC270J J 27 1/2W M-Ox. AA
R708 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R710 VRS-SV2HC103J J 10k 1/2W M-Ox. AA
R711 VRD-RA2BE274J J 270k 1/8W Carbon AA
R713 VRS-SV2HC122J J 1.2k 1/2W M-Ox. AA
R715 VRD-RA2BE150J J 15 1/8W Carbon AA
R716 VRD-RA2BE223J J 22k 1/8W Carbon AA
å R717 RR-DZ0049CEZZ J 3.9M 1/2W Solid AB
or
RR-HZ0048CEZZ
or
VRD-UA2HG395K
R725 VRS-SV2HC821J J 820 1/2W M-Ox. AA
R733 VRD-RA2EE394J J 390k 1/4W Carbon AA
R736 VRD-RM2HD184J J 180k 1/2W Carbon AA
R739 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R740 VRD-RM2HD470J J 47 1/2W Carbon AA
R741 VRN-RA2BK682F J 6.8k 1/8W M-Film AA
R753 VRD-RM2HD124J J 120k 1/2W Carbon AA
R754 VRN-VV3DB8R2J J 8.2 2W M-Film AB
R755 VRS-VV3DB150J J 15 2W M-Ox. AA
R756 VRS-VV3DB121J J 120 2W M-Ox. AA
R759 VRS-VV3DB101J J 100 2W M-Ox. AA
R766 VRS-CY1JF333J J 33k 1/16W M-Ox. AA
R767 VRD-RA2BE103J J 10k 1/8W Carbon AA
R768 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R801 VRS-CY1JF243J J 24k 1/16W M-Ox. AA
R802 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA
R803 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R804 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R805 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R806 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R807 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA
R810 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R812 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R814 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
R815 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
R816 VRS-CY1JF223J J 22k 1/16W M-Ox. AA
R817 VRS-CY1JF473J J 47k 1/16W M-Ox. AA
R818 VRS-VV3AB151J J 150 1W M-Ox. AA
R823 VRD-RA2BE101J J 100 1/8W Carbon AB
R824 VRD-RA2BE101J J 100 1/8W Carbon AB
R825 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R828 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R829 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA
R830 VRS-CY1JF393J J 39k 1/16W M-Ox. AA
R831 VRS-CY1JF271J J 270 1/16W M-Ox. AA
R832 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
R833 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R835 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA
R836 VRD-RA2BE470J J 47 1/8W Carbon AA
R838 VRS-CY1JF105J J 1.0M 1/16W M-Ox. AA
R839 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R840 VRS-CY1JF124J J 120k 1/16W M-Ox. AA
R841 VRD-RA2BE821J J 820 1/8W Carbon AA
R842 VRS-CY1JF471J J 470 1/16W M-Ox. AA
R843 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R850 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA
R851 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R852 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R853 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R854 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R855 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
R1002 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R1003 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
R1006 VRS-CY1JF822J J 8.2k 1/16W M-Ox. AA
R1007 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1008 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R1009 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1021 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1022 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1023 VRD-RA2BE271J J 270 1/8W Carbon AA
R1024 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1026 VRS-CY1JF000J J 0 1/16W M-Ox. AA
R1027 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R1031 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1032 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1034 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1036 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1040 VRD-RA2BE273J J 27k 1/8W Carbon AA
R1041 VRD-RA2BE103J J 10k 1/8W Carbon AA
R1042 VRD-RA2BE101J J 100 1/8W Carbon AB
R1043 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R1045 VRD-RA2BE101J J 100 1/8W Carbon AB
R1046 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1047 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R1048 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1049 VRS-CY1JF183J J 18k 1/16W M-Ox. AA
R1051 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1052 VRS-CY1JF104J J 100k 1/16W M-Ox. AA
R1059 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1061 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R1062 VRS-CY1JF105J J 1.0M 1/16W M-Ox. AA
44
Page 45
14U-FM1
CU14FM1
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PWB-A: DUNTKB177WEA0(14U-FM1)
PWB-A: DUNTKB177WEA1(CU14FM1)
MAIN UNIT (Continued)
R1063 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1064 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1065 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1066 VRS-CY1JF561J J 560 1/16W M-Ox. AA
R1067 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R1068 VRS-CY1JF331J J 330 1/16W M-Ox. AA
R1069 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R1070 VRS-CY1JF331J J 330 1/16W M-Ox. AA
R1071 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R1072 VRS-CY1JF221J J 220 1/16W M-Ox. AA
R1073 VRS-CY1JF101J J 100 1/16W M-Ox. AA
R1074 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
R1075 VRS-CY1JF331J J 330 1/16W M-Ox. AA
R1076 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA
R1081 VRS-CY1JF103J J 10k 1/16W M-Ox. AA
S1001 QSW-K0077GEZZ J CH-Up AB
S1002 QSW-K0077GEZZ J CH-Down AB
S1003 QSW-K0077GEZZ J VOL-Up AB
S1004 QSW-K0077GEZZ J VOL-Down AB
S1005 QSW-K0077GEZZ J MENU AB
S1006 QSW-K0114CEZZ J POWER AE
MISCELLANEOUS PARTS
å RY701 RRLYJ0093CEZZ J Relay AG
å F701 QFS-B4023CEZZ J Fuse, 4A-125V AC
FH701 QFSHD1013CEZZ J Fuse Holder AC
FH702 QFSHD1014CEZZ J Fuse Holder AC
FB701 RBLN-0020CEZZ J Ferrite Bead AB
J402 QJAKE0108CEZZ J Jack, Audio-IN AC
J403 QJAKE0183CEZZ J Jack, Video-IN AE
J405 QJAKF0074CEZZ R Jack, AV-IN AF
P301 QPLGN0241CEZZ J Plug, 2-pin(S) AA
P601 QPLGN0660CEZZ J Plug, 6-pin(K) AC
P602 LHLDW1104PEZZ R Holder, 4-pin(H) AB
P603 QPLGN0361CEZZ J Plug, 3-pin(TP651-3) AB
P701 QPLGN0260CEZZ J Plug, 2-pin(M) AC
P705 QTiPM0083CEZZ J Tip(SG) AB
P1001 LHLDW1105PEZZ R Holder, 5-pin(K) AB
P1002 QPLGN0561CEZZ J Plug, 5-pin(BC) AB
RMC1001
RRMCU0222CEZZ J R/C Receiver AL
TP201 QLUGP0102PEZZ R Lug AA
RDA301
PRDAR0119GJFW R Heat Sink, for IC301 AD
RDA501
PRDAR0118GJFW R Heat Sink, for IC501 AD
RDA602
PRDAR0224PEFW R Heat Sink, for Q602 AF
RDA701
PRDAR0118GJFW R Heat Sink, for Q701 AD
LHLDW1047PEZZ R Holder AB
LHLDW1064PEKZ R Holder AC
LHLDW1104PEZZ R Holder AB
LHLDW1105PEZZ R Holder AB
LX-BZ3049GEFD J Screw AA
LX-BZ3100CEFD J Screw AA
LX-TZ3004CEFD J Screw AA
QCNW-A228WJZZ R Connecting Cord AD
QCNW-A291WJZZ J Connecting Cord AD
QCNW-A292WJZZ J Connecting Cord AD
QCNW-A482WJZZ R Connecting Cord AG
QCNW-A483WJZZ R Connecting Cord AH
QCNW-A484WJZZ R Connecting Cord AE
SWITCHES
PWB-B: DUNTKB178WEA0(14U-FM1)
PWB-B: DUNTKB178WEA1(CU14FM1)
CRT UNIT
TRANSISTORS
Q852 RH-TX0110BMZZ+ R TX0110BM AC
Q854 RH-TX0110BMZZ+ R TX0110BM AC
Q856 RH-TX0110BMZZ+ R TX0110BM AC
Q881 VS2PA1015Y+-1+ R 2PA1015Y+ AC
DIODES
D882 VHD1SS119//-1 J Diode AB
D885 VHD1SS119//-1 J Diode AB
COIL
L852 VP-MK820K0000 J Peaking 82µH AB
CAPACITORS
[EL.··· Electrolytic]
C851 VCCCCY1HH151J J 150p 50V Ceramic AA
C852 VCCCCY1HH151J J 150p 50V Ceramic AA
C853 VCCSPA1HL151J J 150p 50V Ceramic AA
C854 RC-KZ0153CEZZ J 1000p 3kV Ceramic AB
C883 VCEA0A1CW336M J 33 16V EL. AB
RESISTORS
[M-Ox.··· Metal Oxide]
R870 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R871 VRD-RA2BE331J J 330 1/8W Carbon AA
R872 VRS-CY1JF121J J 120 1/16W M-Ox. AA
å R873 VRS-VV3AB123J J 12k 1W M-Ox. AA
R874 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
R875 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R876 VRD-RA2BE331J J 330 1/8W Carbon AA
R877 VRS-CY1JF121J J 120 1/16W M-Ox. AA
R878 VRS-CY1JF271J J 270 1/16W M-Ox. AA
R879 VRS-CY1JF121J J 120 1/16W M-Ox. AA
R880 VRS-CY1JF470J J 47 1/16W M-Ox. AA
R881 VRS-CY1JF561J J 560 1/16W M-Ox. AA
R882 VRS-CY1JF391J J 390 1/16W M-Ox. AA
R883 VRD-RA2BE561J J 560 1/8W Carbon AA
R884 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA
R886 VRS-CY1JF821J J 820 1/16W M-Ox. AA
R887 VRD-RA2BE470J J 47 1/8W Carbon AA
R892 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
å R893 VRS-VV3AB123J J 12k 1W M-Ox. AA
R894 VRD-RM2HD332J J 3.3k 1/2W Carbon AA
å R895 VRS-VV3AB123J J 12k 1W M-Ox. AA
MISCELLANEOUS PARTS
P851 LHLDW1105PEZZ R Holder, 5-pin(K) AB
P852 LHLDW1104PEZZ R Holder, 4-pin(H) AB
SC851 QSOCV0016PEZZ R CRT Socket AF
or
QSOCV0933CEZZ
or
QSOCV0931CEZZ
45
Page 46
14U-FM1
CU14FM1
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
MISCELLANEOUS PARTS
å
ACC701
QACCD3090CESA J AC Cord AC120V 60Hz AK
SP301 VSP9050PB33WA J Speaker AK
LHLDK0025PEZZ R AC Cord Holder AB
LHLDW1003PEZZ R Wire Holder, x3 AA
LHLDW1060PEZZ R Wire Holder, x2 AA
LHLDW1075PEKZ R Wire Holder, x2 AC
LHLDZ0063PEZZ R Anode Clamp Holder AD
LHLDZ0133PEZZ R Wire Holder, x1 AC
LX-NZ3043CEFD J CRT Nut, x5 AA
LX-TZ3004CEFD J Screw, x5 AA
PSPAG0001PE00 R Spacer, x4 AB
QCNW-2206PEZZ R Connecting Cord(SP) AD
TLABM1829PEZZ R Model Label(14U-FM1) AB
TLABM1906PEZZ R Model Label(CU14FM1) AB
TLABRA001WJZZ R Bar Code Label(CU14FM1) AB
XTASD40P20000 J Screw, x4 AA
LANGB0018PEFD R CRT Bracket AF
LHLDZ0015PEZZ R Holder AD
LHLDZ0147PEZZ R Holder AC
MSPRC0005PEFW R Spring AB
PSPAH0073PE00 R Spacer AB
TCAUH0055PEZZ R Caution Card(14U-FM1) AC
TCAUS0004PEZZ R Caution Card(CU14FM1) AD
TCAUS0013PEZZ R Caution Card(CU14FM1) AB
XEBSD30P12000 J Screw AA
XTASD40P20000 J Screw AA
CABINET PARTS
1 CCABA2708WEV0 R Front Cabinet Ass’y BG
1 CCABA2708WEV1 R Front Cabinet Ass’y BG
1-1
1-2 GCOVA0148PESA R Cover for R/C AD
1-3 HDECAA001WJSA R Decoration Plate AG
1-4 JBTN-0402PEKA R Button(Power) AG
1-5 JBTN-0403PEKA R Button(Vol-up/down, AF
1-6 GBFL-0014PEKA R Speaker Baffle AF
2 GCABB2475PEKA R Rear Cabinet AZ
Not Available
(14U-FM1)
(CU14FM1)
– Front Cabinet —
CH-up/down, Menu)
SUPPLIED ACCESSORIES
RRMCG1324CESC J Infrared R/C Unit AR
TGAN-0018PEZZ R Guarantee Card(14U-FM1) AD
TiNS-7638PEZZ R
TiNS-A102WJZZ R
Operation Manual(14U-FM1)
Operation Manual(CU14FM1)
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKCA040WJZZ – Packing Case(CU14FM1) —
SPAKC6799PEZZ – Packing Case(14U-FM1) —
SPAKP0095PEZZ – Wrapping Paper —
SPAKP0110PEZZ – Wrapping Paper —
SPAKX2793PEZZ – Buffer Material —
SSAKA0001PEZZ – Polyethylene Bag —
TLABN0001PEZZ – Serial No. Label —
TLABK0002PEZZ – Label —
AF
AH
CABINET PARTS LOCATION
1
1-4
1-1
1-2
1-5
1-3
1-6
2
46
Page 47
REAR
Use 22 staples
fix the packing case.
★ Packing Case
★ MARK : Not replacement items.
FRONT
★Buffer Material
★ Wrapping Paper
★ Polyethylene Bag
Operation Manual
Guarantee Card(14U-FM1)
Batteries
★ Serial No. Label
★
Infrared R/C Unit
PACKING OF THE SET
14U-FM1
CU14FM1
47
Page 48
14U-FM1
CU14FM1
COPYRIGHT © 2002 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
D SEM P SREC TQ1302-S
Apr. 2002 Printed in Japan
MI. KG
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
Loading...