SHARP 13N-M100B, 13N-M150B, CN13M10B Service Manual

Page 1
13N-M100B/150B CN13M10B
SERVICE MANUAL
SX0K513N-M100
COLOR TELEVISION
Chassis No. SN-010
13N-M100B/150B
MODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
CN13M10B
CONTENTS
Page
» IMPORTANT SERVICE SAFETY PRECAUTION .................................................................................2
» LOCA TION OF USER'S CONTROL .....................................................................................................6
» INST ALLATION AND SER VICE INSTRUCTIONS ................................................................................7
» CHASSIS LAYOUT .............................................................................................................................13
» BLOCK DIAGRAM ..............................................................................................................................14
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................21
» REPLACEMENT PARTS LIST............................................................................................................24
» PACKING OF THE SET ......................................................................................................................31
ELECTRICAL SPECIFICATIONS
POWER INPUT.................................................... 120 V AC 60 Hz
POWER RATING ................................................................... 53 W
PICTURE SIZE ............................................. 580cm2 (89.8sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
Sound IF Carrier Frequency...................................... 41.25 MHz
Color Sub-Carrier Frequency .................................... 42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING ................................ 0.9W (at 10% distortion)
SPEAKER
SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE............................. 32 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF.....................................................75 ohm Unbalanced
TUNING RANGES
VHF-Channels...............................................................2 thru 13
UHF-Channels ............................................................14 thru 69
CATV Channels ...........................................................1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without prior notice.
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
1
Page 2
13N-M100B/150B CN13M10B
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems which are separated by insulating material. The non­isolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE, REPLACE
4A 125V
ONLY WITH SAME TYPE 4A­125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE
When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the pic­ture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)
1. Picture tube in this receiver employs integral implosion protection.
2. Replace with tube of the same type number for continued safety .
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that X­radiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified.
2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically.
3. High voltage should always be kept at the rated value
no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly.
5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry.
6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.
2
Page 3
2 2
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
13N-M100B/150B CN13M10B
BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)
Before returning the receiver to the user, perform the following safety checks.
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators and etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner.
Plug the AC cord directly into a 120 volt AC outlet, (Do not use an isolation transformer for this test).
Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground.
Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor.
Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC line cord plug connection reversed. (If necessary, a non­polarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.
1.5k ohm 10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
CONNECT TO KNOWN EARTH GROUND
SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams.
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.
3
Page 4
13N-M100B/150B CN13M10B
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
1. N'entreprendre aucune modification de tout circuit. C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs peuvent présenter un danger de choc électrique lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur possède deux systèmes de masse qui sont séparées par du matériel d'isolation. Le système de masse non-isolée (sous tension) est pour le circuit du régulateur de tension B+ et le circuit de sortie horizontale. Le système de masse isolée est pour les tensions DC B+ basses et le circuit secondaire du transformateur haute tension. Pour éviter tout risque d'électrocution lors de l'entretien de ce châssis, utiliser un transformateur d'isolation entre le cordon de ligne et la prise de courant.
PRECAUTION: POUR LA PROTECTION CONTINUE CONTRE LES RISQUES
4A 125V
D'INCENDIE, REMPLACER LE FUSIBLE P AR UN FUSIBLE DE MEME TYPE 4A-125V .
REP ARA TION DU SYSTEME A HAUTE TEN­SION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme, supprimer la charge statique en branchant une résistance de 10 k en série avec un fil isolé (comme une sonde d'essai) entre la mise à la terre du tube-image et le fil d'anodel. (Le corden d'alimentation doit être retiré de la prise murale.)
1. Le tube image dans ce récepteur emploie une protection intégrée contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes incassables et qu'après avoir déchargé totalement la haute tension.
LIMITES DES RADIATIONS X ET DE LA HAUTE TENSION
1. Tout le personnel réparateur doit être instruit des instructions et procédés relatifs aux radiations X. Le tube-image, seule source de rayons X dons les téleviseurs transistorisés, n'émet pourtant pas de rayons mesurables si la haute tension est maintenue à un niveau préconisé dans la section "Vérification de la haute tension". C'est seulement quand la haute tension est excessive que les rayons X peuvent entrer dans l'enveloppe du tube-image y compris le conducteur de verre. Il est important de maintenir la haute tension en-dessous du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un voltmètre à haute tension qui doit être périodiquement étalonné.
3. La haute tension doit toujours être maintenue à la valeur de régime -et pas plus haute. L'opération à des tensions plus élevées peut entraîner une panne du tube-image ou du circuit à haute tension et, dans certaines conditions, peut entraîner une radiation dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne correctement, il n'y a aucun problème de radiation X. Chaque fois qu'un châssis couleurs est réparé, la luminosité doit être examinée bout en contrôlant la haute tension à l'aide d'un voltmètre pour s'assurer que la haute tension ne dépasse pas la valeur spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié et ne pas effectuer de modifications déconseillées du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures d'essai sur un récepteur qui présente une haute tension excessive, éviter de s'approcher inutilement du récepteur. Ne pas faire fonctionner le récepteur plus longtemps que nécessaire pour localiser la cause de la tension excessive.
4
Page 5
13N-M100B/150B
2 2
CN13M10B
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
VERIFICATIONS CONTRE L'INCEN-DIE ET LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur , effectuer les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer que les fils ne soient pas pincés ou qu'un outil ne soit pas placé entre le châssis et les autres pièces métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme les boutons de commande non-métalliques, les isolants, le dos du coffret, les couvercles ou blindages de réglage et de compartiment, les réseaux de résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en vérifiant la fuite de courant, de la facon suivante:
Brancher le cordon d'alimentation directem-ent à une prise de courant de 120V. (Ne pas utiliser de transformateur d'isolation pour cet essai).
A l'aide de deux fils à pinces, brancher une résistance de 1,5 k 10 watts en parallèle avec un condensateur de 0,15µF en série avec toutes les pièces métalliques exposées du coffret et une terre connue comme une conduite électrique ou une prise de terre branchée à la terre.
Utiliser un voltmètre CA d'une sensibilité d'au moins 5000/V pour mesurer la chute de tension en travers de la résistance.
T oucher avec la sonde d'essai les pièces métalliques exposées qui présentent une voie de retour au châssis (antenne, coffret métallique, tête des vis, arbres de commande et des boutons, écusson, etc.) et mesurer la chute de tension CA en-travers de la résistance. Toutes les vérifications doivent être refaites après avoir inversé la fiche du cordon d'alimentation. (Si nécessaire, une prise d'adpatation non polarisée peut être utilisée dans le but de terminer ces vérifications.) Tous les courants mesurés ne doivent pas dépasser 0,5 mA. Dans le cas contraire, il y a une possibilité de choc électrique qui doit être supprimée avant de rendre le récepteur au client.
Voltmètre CA
1.5k ohm 10W
0.15µF
SONDE D'ESSAI
AUX PIECES METALLIQUES EXPOSEES
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
BRANCHER A UNE TERRE CONNUE
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans les téléviseurs présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont
234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121
identifiées par la marque " å " et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d'origine. L'utilisation de pièces qui n'ont pas les mêmes caractéristiques que les pièces recommandées par l'usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies, radiations X ou autres accidents.
5
Page 6
13N-M100B/150B CN13M10B
Front Panel
SENSOR AREA FOR REMOTE CONTROL
POWER
Press On. Press again Off.
LOCATION OF USER'S CONTROL
CH
VOL
+
POWER
POWER
VOLUME UP/DOWN
(+) Increases sound. (–) Decreases sound.
VIDEO IN AUDIO
MENU
VIDEO/AUDIO IN TERMINALS
VOL
CH
+
MENU
CHANNEL UP/DOWN – MENU
(
'
) Selects next higher channel.
(
) Selects next lower channel.
"
• Press both at the same time to access the MAIN MENU screen.
Basic Remote Control Functions
POWER
Press On. Press again Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
VOLUME UP/DOWN
(+) Increases sound. (–) Decreases sound.
• In menu mode, changes or selects
MUTE
Press Mutes sound. Press again Restores sound.
• CLOSED CAPTION appears when
adjustments.
the TV
sound is muted.
Infrared Transmitter Window
INPUT
Press Switch to e xternal video input mode. Press again Switch to TV mode.
CHANNEL UP/DOWN
'
( ) Selects next higher channel. ( ) Selects next lower channel.
"
• Moves the “
” mark of the MENU
screen.
MENU
Press Accesses MAIN MENU. Press again Exits MAIN MENU.
DISPLAY
Press Displa ys receiving channel for four seconds. Press again Removes display.
• Temporarily displays receiving channel when in Closed Caption mode.
6
TV
Page 7
13N-M100B/150B CN13M10B
INSTALLATION AND SERVICE INSTRUCTIONS
Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2)Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.
X-RADIA TION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate input voltage.
2. Allow for warm up and adjust all customer controls for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 21.1 ±1.5V.
5. Apply external 27.9V DC at TP653 by using an external DC supply , TV must be shut of f.
6. To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652. Now make sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.
HIGH VOL T AGE CHECK
High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:
1. Connect an accurate high voltage meter between ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC line voltage, with a strong air signal or a properly tuned in test signal.
3. Enter the service mode and select the service adjustment "S03" and Bus data "01" (Y-mute on).
4. The voltage should be approximately, 24.0kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode.
7
Page 8
13N-M100B/150B CN13M10B
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage. Follow
the steps below whenever the service adjusment is required.
To enter the service mode and exit service mode.
While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket. Now, the TV set is switched on and enters the service mode. To exit the service mode, turn the television off by pressing the power button.
1. Service mode.
Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset function in the video adjustment menu to ensure customer control are in their proper (reset) position.
2. Service number selection.
In the service mode, you will see the window screen as window 1. There are 3 adjustment categories 2DEF, 3SIGNAL, 4FIX VALUE as show in Figure A.
Window 2: DEF
D01 D03 D05
RETURN
RETURN
Window 4: FIX VALUE
D02 D04 D06
Window 1: ADJUSTMENT CATEGORIES
RETURN
F01 F02
F13 F14
RETURN NEXT
DEF
SERVICE MODE
DEF SIGNAL FIX V ALUE EEPROM
NEXT
PREVIOUS
SIGNAL
FIX V ALUE
Window 3: SIGNAL
S01
S13 RETURN
F15 F16
F25 F26
RETURNPREVIOUS
S02 S12
RETURN
Figure A: ADJUSTMENT CATEGORIES
Press CH UP/DOWN button for selection and enter by VOL UP or VOL DOWN. Press CH UP/DOWN button to select the adjustment item and VOL UP/DOWN to adjust the data number for each categories.
(OSD disturbance can be erased by R/C display key) (Note: EEPROM-factory used only)
8
Page 9
Below are the adjustments ranges and initial values for FIX VALUE category.
FIX V ALUE
SERVICE
POSITION
F01 OPTION 1 00-FF B0 F02 OPTION 2 00-FF 04 04 F03 E-SAVE 00-3F 23 2A F04 TUNER SETUP 00, 01 00 00 F05 R-TONE RD 00-7F 19 03 F06 R-TONE BD 00-7F 00 7C F07 B-TONE RD 00-7F 00 00 F08 B-TONE BD 00-7F 12 04 F09 FM LEVEL 00-1F 0C 0C F10 AFC GAIN 00, 01 00 00 F11 G DRIVE 00, 0F 00 0F F12 FBT BLK SW 00,01 01 01 F13 V COMP 00-07 07 07 F14 OSD CONT 00-03 02 01 F15 SHARPNESS 00-3F 19 19 F16 FLT SYS 00-07 00 00 F17 KILLER OP 00-07 04 02 F18 PRE SHOOT 00-03 03 00 F19 CORING 00-03 04 04 F20 DC REST 00-03 02 02 F21 BS START 00-03 01 01 F22 BS GAIN 00-03 01 01 F23 ABL START 00-07 00 00 F24 R/B ANGLE 00-0F 08 08 F25 H BLK R 00-0F 04 03 F26 H BLK L 00-0F 04 06
ADJUST ITEM
RANGE
* Must be "B0" for 13N-M100B/150B, "A0" for CN13M10B
Table - A
DATA
INITIAL VALUE
13N-M100B/150B CN13M10B
(Hex)
*
Below are the ranges and initial values for each adjustment and in each categories.
DEF
SERVICE
POSITION
D01 H-PHASE 00-1F 0C D02 V-SIZE 00-7F 40 D03 V-POSITION 00-3F 20 Must be "20" D04 CC-POSITION 00-FF 1A D05 V-LINEARITY 00-1F 10 Must be "12" D06 V-S-CORRECTION 00-1F 10 Must be "0F"
ADJUST ITEM
RANGE
DATA
T able - B
INITIAL VALUE
ADJUSTMENT CONTENTS
SIGNAL
SERVICE
POSITION
S01 RF AGC 00-3F 14 S02 VIDEO LEVEL 00-07 03
S03 Y-MUTE 00-03 00 S04 SUB BIAS 00-FF 40 Must be "60"
S05 R-BIAS 00-FF 00 S06 G-BIAS 00-FF 00 S07 B-BIAS 00-7F 00 S08 R-DRIVE 00-7F 40 S09 B-DRIVE 00-7F 40 S10 CONTRAST 00-7F 5A S11 TINT 00-7F 40 S12 COLOR 00-7F 40 S13 BRIGHTNESS 00-7F 40
ADJUST ITEM
RANGE
Note: Refer to the SERVICE ADJUSTMENT for each corresponding values.
Table - C
DATA
INITIAL VALUE
ADJUSTMENT CONTENTS
"01": Y-MUTE, "02": V-STOP & Y-MUTE
Activate color killer circuit.
"03":
9
Page 10
13N-M100B/150B CN13M10B
Holding down both the Vol-up/Ch-down buttons on the TV set at service mode for more than 2 seconds will automatically write the above initial values into IC2101.
PAR T REPLACED
IC2001
IC201
IC2101
CRT
ADJUSTMENT
NECESSARY
X
X
X
UNNECESSARY
X
Table - D
NOTES
Data is stored in IC2101. The adjustment is needed to compensate for characteristics
of parts including IC201.
Holding down both the Vol-up/Ch-down buttons on the TV set in the service mode for more than 2 seconds will automatically write the above initial values into IC2101.
Adjust items related to picture tube only .
10
Page 11
Ë
SERVICE ADJUSTMENT
Note: Before making the service adjustment, make the
bus data settings.
+B Adjustment
1. Receive a good local channel.
2. Select VIDEO ADJUSTMENT RESET on the menu to get the video reset.
3. Connect a DC voltmeter between the +B line (at SW transformer) of R611 and the ground terminal.
4. Adjust R738 so that the voltmeter should read 130±0.5V.
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select the service adjustment "S01".
3. Set the data value to point where no noise or beat appears.
4. Select another channel to confirm that no noise or beat appears.
Note: You have to exit the service mode first to
select another channel.
13N-M100B/150B CN13M10B
6. Adjust the master screen control untill the raster darkens to the point where raster is barely seen.
7. Adjust the service adjustment "S05" red, "S06" green, "S07" blue to obtain a good grey scale with normal white at low brightness level.
8. Select the service a adjustment "S03" and reset data to "00". Select the service adjustment "S12" and reset data to obtain normal color level.
9. Remove probe and reset the master screen control to obtain normal brightness range.
White Balance Adjustment.
1. Receive a good local channel.
2. Select the service adjustment "S12" and set the data value to "00" to set the color level to the minimun. Y ou may skip this step, if you selected a B/W picture or monoscope.
3. Alternately adjust the service adjustment data of "S08" and "S09" untill a good grey scale with normal white is obtained.
4. Select the service adjustment "S12" and reset data to obtain normal color level.
Video Level (TV Det Video Level) Adjustment
1. Receive a good local channel.
2. Enter the service mode signal category and select the service adjustment "S02".
3. Set the data value to "02" first, then adjust the data in ranges 02 ±2 step to obtain a normal contrast level.
Screen adjustment
1. Connect to oscilloscope probe between TP855 and ground of the CRT unit.
2. Receive a good local channel.
3. Enter the service mode Signal category and set the service adjustment "S04" to step 60. Then select the service adjustment "S12" and set the data value to "00" to set the color level to the minimum level. (record the original data first). You may skip this step, if you selected a B/W picture or monoscope pattern. Set also the "S05/S06/S07" data to minimum level.
4. Select the service adjustment "S03" and set the data value to "01" to turn off the luminance signal (Y -mute).
5. Select the service adjustment "S13" and adjust the data value to obtain 2.40 volts as shown in Figure B.
Sub-Picture Adjustment
1. Receive a good local channel.
2. Make sure the customer picture control is set to maximum.
3. Enter the service mode and select the service adjustment "S10".
4. Adjust the data value to achieve normal contrast range.
Sub-Tint Adjustment
1. Receive a good local channel.
2. Set the customer tint control to the center of it’s range.
3. Enter the service mode and select the service adjustment "S11".
4. Adjust "S1 1" data value to obtain normal fresh tones.
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center position.
3. Enter the service mode and select the service adjustment "S12".
4. Adjust "S12" data value to obtain normal color level.
2.40 Vdc
GND
Figure B: WAVEFORM FOR SCREEN ADJUSTMENT
Sub-Brightness Adjustment
1. Receive a good local channel.
2. Make sure the customer brightness control is set to center position.
3. Enter the service mode and select the service adjustment "S13".
4. Adjust "S13" data value to obtain normal brightness level.
11
Page 12
13N-M100B/150B CN13M10B
Vertical-Size, V-Linearity, V-S Correction Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the adjustment "D02" for Vertical Size, "D05" for V­Linearity and "D06" for V-S Correction Adjustment.
3. Set in order "D05" for V-Linearity, "D06" for V-S Correction and set the data to get the best linearity.
4. Then adjust "D02" data unitll it become a proper vertical size.
Horizontal Position Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the adjustment "D01".
3. Adjust "D01" data value to center the picture.
Vertical-Phase Adjustment
1. Receive a good local channel.
2. Enter the service mode DEF category and select the adjustment "D03".
3. Adjust "D03" bus data to get the most acceptable vertical position.
Note: The step range is 20 ±10.
Caption Position Adjustment (Horizontal)
1. Receive a good local channel.
2. Enter the service mode DEF category and select the adjustment "D04".
3. A black text box will appear on the screen. (see Figure C. below)
4. Adjust "D04" data value to balance the text box position in the center. (A=B).
A B
Figure C.
12
Page 13
CHASSIS LAYOUT
13N-M100B/150B CN13M10B
H
G
F
PWB-A
E
PWB-B
D
C
B
A
13
654321
Page 14
13N-M100B/150B CN13M10B
BLOCK DIAGRAM
H
G
F
E
D
C
B
A
654321
14
Page 15
DESCRIPTION OF SCHEMATIC DIAGRAM
13N-M100B/150B CN13M10B
NOTES:
1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/10 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted. (P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5. indicates line isolated ground.
VOL T AGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color signal.
WAVEFORMS
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control.
2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)
å
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
'
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES å ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE ' : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.
15
Page 16
MODELS 13N-M100B/150B SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
13N-M100B/150B CN13M10B
E
D
C
B
A
121110987654321
16
17
Page 17
MODEL CN13M10B SCHEMATIC DIAGRAM: MAIN Unit
H
G
F
13N-M100B/150B CN13M10B
E
D
C
B
A
121110987654321
18
19
Page 18
13N-M100B/150B CN13M10B
SCHEMA TIC DIAGRAM: CRT Unit
H
G
F
E
D
C
B
A
654321
20
Page 19
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
13N-M100B/150B CN13M10B
PWB-B: CRT Unit (Wiring Side)
E
D
C
B
PWB-B: CRT Unit (Chip Parts Side)
A
654321
21
Page 20
13N-M100B/150B CN13M10B
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Wiring Side)
A
654321
22
Page 21
13N-M100B/150B CN13M10B
H
G
F
E
D
C
B
PWB-A: MAIN Unit (Chip Parts Side)
A
654321
23
Page 22
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PARTS LIST
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT P ARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER 2. REF. NO.
3. PAR T NO. 4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor, Please call Toll­Free; 1-800-BE-SHARP
MARK: SP ARE PARTS-DELIVERY SECTION
MARK: X- RAY RELATED PARTS
Ref. No. Part No. Description Code
LISTE DES PIECES
CHANGE DES PIECES
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep éler élee par la marque å et sont hachur élees dans les listes de pi`eces et dans les diagrammes sch élematiques. La substitution d'une pi`ece de rechange par une autre qui ne pr éLesente pas les m éoemes caract éLeristiques de s élecurit éle que la pi`ece recommand élee parl'usine et dans ce manuel de service, peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie, veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE 2. NO. DE REF
3. NO. DE PIECE 4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
MARQUE: PIECES RELATIVE AUX RAYONS X
Ref. No. Part No. Description Code
PICTURE TUBE
V101 VB37GDA86X/1E R CRT (DY601: H0142PE) CB
or VB34KPU02X/*S CRT (DY601: H0141PE) or VB34JFQ90X/*S CRT (DY601: H0143PE) or VB34LRQ90X/*S CRT (DY601: H0143PE) or VB370BVBK1S-S CRT (DY601: H0143PE) or VB34JLL90X/*S CRT (DY601: H0144PE) or VB34EJM34X/1E CRT (I.T.C.)
DY601 RCiLH0142PEZZ R DY (CRT: 37GDA86X) AZ
or RCiLH0141PEZZ DY (CRT: A34KPU02XX) or RCiLH0143PEZZ DY (CRT: CPJ370BVBK1S or or A34JFQ90X
or A34LRQ90X)
RCiLH0144PEZZ DY (CRT: A34JLL90X)
å L703 RCiLG0092PEZZ R Degaussing Coil AK
or RCiLG0077PEZZ or RCiLG0386PEZZ PMAGF3045CEZZ R Purity Magnet AG QEARC1436PEZZ R Grounding Strap AE
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
PWB-A DUNTKA358WEV0 – PWB-A DUNTKA358WEV3 – MAIN Unit (CN13M10B) — PWB-B DUNTKA359WEV0 – PWB-B DUNTKA359WEV3 – CRT Unit (CN13M10B)
PWB-A: DUNTKA358WEV0 (13N-M100B/150B) PWB-A: DUNTKA358WEV3 (CN13M10B)
MAIN UNIT
NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
å TU51 VTUVTST5UF770 J Tuner AZ
or VTUVTST5UF78S or VTUENV56D82-1
INTEGRATED CIRCUITS
IC201 RH-iX3354CEZZ J LX3354CE AT
IC351 VHiAN7511//-1 J AN7511 AK
å IC501 VHiLA7840//-1 J LA7840 AR å IC701 VHiTEA1507/-1 J TEA1507P/N1 AL å IC702 RH-FX0034CEZZ J PC817 AE
or RH-FX0002GEZZ or RH-FX0029CEZZ
MAIN Unit (13N-M100B/150B) CRT Unit (13N-M100B/150B)
TUNER
— —
24
Page 23
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA358WEV0 (13N-M100B/150B) PWB-A: DUNTKA358WEV3 (CN13M10B)
MAIN UNIT (Continued)
å IC771 VHiKA7805AP-1 J KIA7805API AE
å Q602 VS2SD2586//1E J 2SD2586 AM
å Q701 VS2SK2645++-1 J K2645++ (CN13M10B) AN
å Q701 VSSPP04N60C-1 J
å Q702 VS2SC945AQ/-1 J 2SC945AQ AB
or
VHiTA7805S/-1 IC2001 RH-iX3492CEZZQ J IX3492CE AU IC2040 VHiPST994C/-1 J PST994C AD IC2101 VHiBR24C02/-1 J I.C. (CN13M10B) AL
or
VHiM24C02B/-1 IC2101 VHiM24C16B/-1 J M24C16-BN6 AG
or (13N-M100B/150B)
VHiBR24C16/-1
TRANSISTORS
Q101 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198-Y-1
or
VS2SC1815Y/-1 Q201 VS2SC2735//1E J 2SC2735 AC Q451 VS2SA1530R/-1 J 2SA1530R AB Q452 VS2SA1266-Y-1 J 2SA1266(Y) AA Q601 VS2SC2482//-1 J 2SC2482 AD
Q631 VS2SC945AQ/-1 J 2SC945AQ AB
or
VS2SC3198-Y-1
or
VS2SC1815Y/-1
or
VS2SK2708//1E
or
VSSTP6NC60F-1
SPP04N60 (13N-M100B/150B)
AH or VSSPP07N60C-1 or VS2SK2708//1E or VS2SK2645++-1 or VSSTP6NC60+-1 or VSSTP6NC60F-1
or VS2SC3198-Y-1 or VS2SC1815Y/-1
Q751 VS2SC945AQ/-1 J 2SC945AQ AB
or VS2SC3198-Y-1 or VS2SC1815Y/-1
Q752 VS2SC945AQ/-1 J 2SC945AQ AB
or VS2SC3198-Y-1 or VS2SC1815Y/-1
Q2201 VS2SC3928R/-1 J 2SC3928R AB
or VS2PD601AR/-1
Q2211 VS2SC3928R/-1 J 2SC3928R AB
DIODES
D52 RH-EX0676GEZZ J Zener Diode, 32V AA D101 RH-EX0616GEZZ J Zener Diode, 5.6V AA D352 RH-DX0475CEZZ J Diode AB
or VHD1SS119//-1
D353 RH-EX0644GEZZ J Zener Diode, 13V AB
D453 RH-EX0616GEZZ J Zener Diode, 5.6V AA D455 RH-DX0475CEZZ J Diode AB
D502 RH-DX0131CEZZ J Diode AC
D510 RH-EX0654CEZZ J Zener Diode, 75V AD D511 RH-DX0441CEZZ J Diode AC D610 RH-DX0131CEZZ J Diode AC D632 RH-EX0630GEZZ J Zener Diode, 9.1V AA D641 RH-EX0630GEZZ J Zener Diode, 9.1V AA
D651 VHD1SS244//-1 J Diode ABD653 RH-EX0667GEZZ J Zener Diode, 27V AA
å D661 RH-DX0468CEZZ J Diode AE
or RH-DX0229CEZZ
å D701 RH-DX0490CEZZ J Diode AC
or RH-DX0154CEZZ
å D702 RH-DX0490CEZZ J Diode AC
or RH-DX0154CEZZ
å D703 RH-DX0490CEZZ J Diode AC
or RH-DX0154CEZZ
å D704 RH-DX0490CEZZ J Diode AC
or RH-DX0154CEZZ
D707 RH-DX0475CEZZ J Diode AB
or VHD1SS244//-1
D708 RH-DX0475CEZZ J Diode AB
or VHD1SS244//-1
å D709 RH-DX0229CEZZ J Diode AF å D712 RH-DX0487CEZZ J Diode AC
or RH-DX0302CEZZ or RH-DX0468CEZZ or VHDD1NS4///-1 or RH-DX0513CEZZ
D717 RH-EX0616GEZZ J Zener Diode, 5.6V AA
å D725 RH-DX0131CEZZ J Diode AC
D726 RH-DX0475CEZZ J Diode AB
or
VHD1SS119//-1 D751 RH-EX0611GEZZ J Zener Diode, 5.1V AA D753 RH-DX0441CEZZ J Diode AC
or
RH-DX0110CEZZ
å D758 RH-DX0131CEZZ J Diode AC
D2001 RH-DX0475CEZZ J Diode AB
or
VHD1SS119//-1
å VA701 RH-VX0048CEZZ J Varistor (13N-M100B/150B) AE
or
RH-VX0035CEZZ
PACKAGED CIRCUITS
å PR701 RMPTP0026CEZZ J Packaged Circuit AF
X801 RCRSB0001PEZZ R Crystal AL
or
RCRSB0205CEZZ
FILTERS
CF2040
RFiLA0099CEZZ J Ceramic Filter AE
or
RFiLC0121GEZZ SF201 RFiLC0441CEZZ J SAW Filter AH
COILS
L201 VP-XF1R2K0000 J Peaking 1.2µH AB L202 VP-XF1R2K0000 J Peaking 1.2µH AB L203 VP-XF220K0000 J Peaking 22µH AB L204 RCiLi0632CEZZ J IF Coil AE
25
Page 24
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA358WEV0 (13N-M100B/150B) PWB-A: DUNTKA358WEV3 (CN13M10B)
MAIN UNIT (Continued)
L301 VP-XF150K0000 J Peaking 15µH AB
å L701 RCiLF0078PEZZ R Coil AF
or RCiLF0069PEZZ or RCiLF0037PEZZ or RCiLF0029PEZZ
å L702 RCiLF0090CEZZ R Coil (CN13M10B) AL å L705 RCiLP0179CEZZ J Coil AD
L2040 RCiLB0131CEZZ J Oscillation Coil AE
TRANSFORMERS
å T601 RTRNZ0731CEZZ J Transformer AG
or RTRNZ0026PEZZ
T602 RTRNF0212PEZZ R H-Volt Transformer AY
å T702 RTRNW0004PEZZ R Transformer AL
or RTRNW0008PEZZ
CONTROL
R738 RVR-M4628GEZZ J 22k AB
or RVR-M4336CEZZ
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
C51 VCEA0A1CW337M J 330 16V EL. AC C53 VCEA0A1HW105M J 1.0 50V EL. AB C54 VCEA0A1HW475M J 4.7 50V EL. AB C101 VCEA0A1CW476M J 47 16V EL. AB C201 VCKYCY1HF103Z J 0.01 50V Ceramic AA C202 VCKYCY1HF103Z J 0.01 50V Ceramic AA C203 VCKYCY1HF103Z J 0.01 50V Ceramic AA C204 VCQYTA1HM223K J 0.022 50V Mylar AB C205 VCKYPA1HB103K J 0.01 50V Ceramic AA C206 VCKYCY1HB102K J 1000p 50V Ceramic AA C207 VCEA0A1CW476M J 47 16V EL. AB C208 VCKYCY1HF103Z J 0.01 50V Ceramic AA C209 VCEA0A1HW105M J 1.0 50V EL. AB C210 VCEA0A1HW474M J 0.47 50V EL. AB C211 VCKYCY1HB102K J 1000p 50V Ceramic AA C212 VCEA0A1HW474M J 0.47 50V EL. AB C220 VCKYCY1CB104K J 0.1 16V Ceramic AB C301 VCCCCY1HH470J J 47p 50V Ceramic AA C302 VCKYCY1HB102K J 1000p 50V Ceramic AA C304 VCCCCY1HH470J J 47p 50V Ceramic AA C305 VCKYCY1HB103K J 0.01 50V Ceramic AA C306 VCQYTA1HM103K J 0.01 50V Mylar AB C354 VCEA0A1HW225M J 2.2 50V EL. AB C356 VCKYCY1HB332K J 3300p 50V Ceramic AA C357 VCEA0A1HW106M J 10 50V EL. AB C358 VCEA0A1HW106M J 10 50V EL. AB C361 VCEA0A1CW227M J 220 16V EL. AC C401 VCCCCY1HH470J J 47p 50V Ceramic AA C411 VCEA0A1AW108M J 1000 10V EL. AC C412 VCKYCY1HB103K J 0.01 50V Ceramic AA C414 VCEA0A1HW225M J 2.2 50V EL. AB C416 VCEA0A1HW105M J 1.0 50V EL. AB C418 VCKYCY1HB103K J 0.01 50V Ceramic AA C421 VCEA0A1HW106M J 10 50V EL. AB C451 VCQYTA1HM563K J 0.056 50V Mylar AB C454 VCEA0A1HW475M J 4.7 50V EL. AB C456 VCEA0A1HW475M J 4.7 50V EL. AB C509 VCKYPA2HB102K J 1000p 500V Ceramic AA C510 VCEA0A1VW477M J 470 35V EL. AB C512 VCFYSA1JB224J J 0.22 63V Mylar AD C513 VCFYSA1JB473J J 0.047 63V Mylar AC C514 VCEA0A1EW477M J 470 25V EL. AD C515 VCEA0A1HW475M J 4.7 50V EL. AB
C516 VCKYCY1HB222K J 2200p 50V Ceramic AA C517 VCEA0A1CW226M J 22 16V EL. AB C520 VCEA0A1HW107M J 100 50V EL. AB C530 VCFYFA1HA334J J 0.33 50V Mylar AB C531 VCFYFA1HA564J J 0.56 50V Mylar AB C606 VCKYPA2HB561K J 560p 500V Ceramic AA C607 VCKYPA1HB472K J 4700p 50V Ceramic AA
C610 VCFPVC3CA522H J 5200p 1.6kV M-Poly. AD
C612 VCFPPB2EB334J J 0.33 250V M-Poly. AF C633 VCEA0A1AW337M J 330 10V EL. AC C634 VCKYCY1HF103Z J 0.01 50V Ceramic AA C635 VCEA0A1HW105M J 1.0 50V EL. AB C636 VCQYTA1HM153K J 0.015 50V Mylar AA C637 VCEA0A1CW476M J 47 16V EL. AB C638 VCEA0A1AW477M J 470 10V EL. AC C652 VCEA0A1HW475M J 4.7 50V EL. AB C653 VCEA0A1HW105M J 1.0 50V EL. AB C661 VCKYPA2HB152K J 1500p 500V Ceramic AA C662 VCEA0A1CW477M J 470 16V EL. AC
å C701 RC-FZ035SCEZZ J 0.047
AC250V
Plastic AC or (13N-M100B/150B) RC-FZ004SGEZZ or RC-FZ015SCEZZ or RC-FZ027SCEZZ
C702 RC-KZ0029CEZZ J 0.01 C703 RC-KZ0029CEZZ J 0.01
å C705 RC-EZ1022CEZZ J 470 200V EL. AK å C706 RC-KZ0092GEZZ J
0.0033
AC250V
Ceramic AC
AC250V
Ceramic AC
AC250V
Ceramic AC or RC-KZ021SCEZZ or RC-KZ009SCEZZ or RC-KZ0106GEZZ or RC-KZ0156CEZZ
å C708 RC-FZ037SCEZZ J 0.22
AC250V
Plastic AD or (CN13M10B) RC-FZ012SGEZZ or RC-FZ017SCEZZ or RC-FZ029SCEZZ
C717 VCKYPA2HB472K J 4700p 500V Ceramic AB
å C723 RC-EZ0638CEZZ J 33 160V EL. AG å C725 RC-EZ0724CEZZ J 100 160V EL. AG
C726 RC-KZ0338CEZZ J 560p 2kV Ceramic AD C727 VCKYPA2HB472K J 4700p 500V Ceramic AB
å C730 VCEA0A1CW108M J 1000 16V EL. AD å C731 VCEA0A1EW107M J 100 25V EL. AC
C732 VCKYPA1HF103Z J 0.01 50V Ceramic AA C735 VCCCPA1HH680J J 68p 50V Ceramic AA C737 VCEA0A1EW226M J 22 25V EL. AB C738 RC-KZ0340CEZZ J 820p 2kV Ceramic AD C739 VCEA0A1HW104M J 0.1 50V EL. AB C740 VCEA0A1EW476M J 47 25V EL. AB C743 RC-KZ0338CEZZ J 560p 2kV Ceramic AD C750 VCKYPA1HF103Z J 0.01 50V Ceramic AA C752 VCEA0A1CW476M J 47 16V EL. AB C753 RC-KZ0338CEZZ J 560p 2kV Ceramic AD
(13N-M100B/150B) C754 VCEA0A1CW476M J 47 16V EL. AB C758 VCEA0A2EW106M J 10 250V EL. AD C759 VCKYPA2HB102K J 1000p 500V Ceramic AA C760 VCEA0A1CW108M J 1000 16V EL. AD C771 VCEA0A1CW476M J 47 16V EL. AB C772 VCEA0A1CW476M J 47 16V EL. AB C783 VCQYTA1HM103K J 0.01 50V Mylar AB C801 VCCCCY1HH180J J 18p 50V Ceramic AA C807 VCKYCY1EF104Z J 0.1 25V Ceramic AA C808 VCEA0A1CW106M J 10 16V EL. AB C811 VCKYCY1CB473K J 0.047 16V Ceramic AA C812 VCEA0A1HW474M J 0.47 50V EL. AB
26
Page 25
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA358WEV0 (13N-M100B/150B) PWB-A: DUNTKA358WEV3 (CN13M10B)
MAIN UNIT (Continued)
C901 VCEA0A1HW105M J 1.0 50V EL. AB C905 VCEA0A1HW106M J 10 50V EL. AB C2001 VCCCCY1HH101J J 100p 50V Ceramic AA C2002 VCCCCY1HH101J J 100p 50V Ceramic AA C2040 VCEA0A1AW107M J 100 10V EL. AB C2041 VCEA0A1HW105M J 1.0 50V EL. AB C2060 VCKYCY1CB104K J 0.1 16V Ceramic AB C2061 VCKYCY1HB222K J 2200p 50V Ceramic AA C2062 VCEA0A1AW107M J 100 10V EL. AB C2201 VCKYCY1HB682K J 6800p 50V Ceramic AA C2601 VCEA0A1HW475M J 4.7 50V EL. AB C2602 VCCCCY1HH101J J 100p 50V Ceramic AA
RESISTORS
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
RJ2 VRN-MD2AL000J J 0 1/10W M-Film AA RJ7 VRN-MD2AL000J J 0 1/10W M-Film AA RJ8 VRN-MD2AL000J J 0 1/10W M-Film AA RJ9 VRN-MD2AL000J J 0 1/10W M-Film AA RJ10 VRN-MD2AL000J J 0 1/10W M-Film AA RJ12 VRN-MD2AL000J J 0 1/10W M-Film AA RJ18 VRN-MD2AL000J J 0 1/10W M-Film AA RJ19 VRN-MD2AL000J J 0 1/10W M-Film AA RJ20 VRN-MD2AL000J J 0 1/10W M-Film AA RJ21 VRN-MD2AL000J J 0 1/10W M-Film AA RJ26 VRN-MD2AL000J J 0 1/10W M-Film AA
å R53 VRS-VU3LE223J J 22k 3W M-Ox. AC
R54 VRN-MD2AL101J J 100 1/10W M-Film AA R55 VRN-MD2AL101J J 100 1/10W M-Film AA R56 VRN-MD2AL823J J 82k 1/10W M-Film AA R57 VRD-RA2BE563J J 56k 1/8W Carbon AA
or
VRD-RA2BE392J R101 VRD-RA2BE152J J 1.5k 1/8W Carbon AA R201 VRN-MD2AL221J J 220 1/10W M-Film AA R202 VRN-MD2AL122J J 1.2k 1/10W M-Film AA R203 VRN-MD2AL682J J 6.8k 1/10W M-Film AA R204 VRN-MD2AL270J J 27 1/10W M-Film AA R205 VRD-RA2BE680J J 68 1/8W Carbon AA R206 VRD-RA2EE151J J 150 1/4W Carbon AA R207 VRD-RA2BE123J J 12k 1/8W Carbon AA R208 VRN-MD2AL332J J 3.3k 1/10W M-Film AA R209 VRN-MD2AL123J J 12k 1/10W M-Film AA R210 VRN-MD2AL104J J 100k 1/10W M-Film AA R211 VRN-MD2AL104J J 100k 1/10W M-Film AA R212 VRN-MD2AL000J J 0 1/10W M-Film AA R215 VRN-MD2AL000J J 0 1/10W M-Film AA R220 VRN-MD2AL331J J 330 1/10W M-Film AA R301 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R302 VRN-MD2AL332J J 3.3k 1/10W M-Film AA R353 VRD-RA2BE683J J 68k 1/8W Carbon AA R354 VRN-MD2AL103J J 10k 1/10W M-Film AA R355 VRD-RA2BE223J J 22k 1/8W Carbon AA R357 VRN-MD2AL822J J 8.2k 1/10W M-Film AA R401 VRN-MD2AL101J J 100 1/10W M-Film AA R402 VRN-MD2AL101J J 100 1/10W M-Film AA R403 VRN-MD2AL101J J 100 1/10W M-Film AA R404 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R411 VRN-MD2AL684J J 680k 1/10W M-Film AA R412 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R413 VRN-MD2AL152J J 1.5k 1/10W M-Film AA R414 VRN-MD2AL000J J 0 1/10W M-Film AA R421 VRN-MD2AL223J J 22k 1/10W M-Film AA
å R451 VRS-SV2HC103J J 10k 1/2W M-Ox. AA
R453 VRD-RA2BE152J J 1.5k 1/8W Carbon AA R454 VRD-RA2EE224J J 220k 1/4W Carbon AA R455 VRD-RA2BE392J J 3.9k 1/8W Carbon AA R456 VRN-MD2AL103J J 10k 1/10W M-Film AA R457 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R461 VRN-MD2AL184J J 180k 1/10W M-Film AA R462 VRN-MD2AL273J J 27k 1/10W M-Film AA R512 VRD-RM2HD102J J 1.0k 1/2W Carbon AA
R513 VRD-RM2HD102J J 1.0k 1/2W Carbon AA R514 VRD-RM2HD1R0J J 1.0 1/2W Carbon AA R515 VRS-VU3AE391J J 390 1W M-Ox. AB R516 VRN-MD2AL153J J 15k 1/10W M-Film AA R517 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R518 VRN-MD2AL333J J 33k 1/10W M-Film AA R519 VRN-MD2AL103J J 10k 1/10W M-Film AA R520 VRD-RM2HD1R2J J 1.2 1/2W Carbon AA R522 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R523 VRD-RA2BE562J J 5.6k 1/8W Carbon AA R525 VRD-RA2BE272J J 2.7k 1/8W Carbon AA R527 VRD-RA2BE223J J 22k 1/8W Carbon AA R528 VRD-RA2BE272J J 2.7k 1/8W Carbon AA R529 VRD-RA2BE472J J 4.7k 1/8W Carbon AA
å R604 VRS-VU3LE562J J 5.6k 3W M-Ox. AC
R605 VRD-RA2BE121J J 120 1/8W Carbon AA R606 VRD-RA2BE102J J 1.0k 1/8W Carbon AA
å R608 VRS-VU3DE391J J 390 2W M-Ox. AB å R609 VRS-VU3AE562J J 5.6k 1W M-Ox. AK
R610 VRD-RM2HD220J J 22 1/2W Carbon AA
å R611 VRS-KA3HG3R3K J 3.3 5W M-Ox. AD
R622 VRN-MD2AL222J J 2.2k 1/10W M-Film AA R623 VRN-MD2AL103J J 10k 1/10W M-Film AA R624 VRN-RA2BK472F J 4.7k 1/8W M-Film AA R634 VRD-RM2HD121J J 120 1/2W Carbon AA R635 VRN-MD2AL332J J 3.3k 1/10W M-Film AA R636 VRD-RA2EE221J J 220 1/4W Carbon AA
å R641 VRS-VU3AE682J J 6.8k 1W M-Ox. AB
R651 VRD-RM2HD270J J 27 1/2W Carbon AA
å R653 VRN-MD2AL000J J 0 1/10W M-Film AAR654 VRD-RA2BE154J J 150k 1/8W Carbon AAR655 VRN-MD2AL103J J 10k 1/10W M-Film AA
å R659 VRN-VV3AB1R5J J 1.5 1W M-Film AA
å R661 VRN-VV3ABR47J J 0.47 1W M-Film AAR662 VRD-RA2BE102G J 1.0k 1/8W Carbon AB
å R702 RR-DZ0049CEZZ J 3.9M 1/2W Carbon AB
or RR-HZ0048CEZZ
å R703 VRW-KP3HC1R8K J 1.8 5W Cement AC
å R705 VRN-VV3ABR47J J 0.47 1W M-Film AA
å R706 VRN-VV3ABR47J J 0.47 1W M-Film AA
R707 VRD-RM2HD270J J 27 1/2W Carbon AA R708 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R710 VRS-SV2HC102J J 1.0k 1/2W M-Ox. AA R711 VRN-MD2AL334J J 330k 1/10W M-Film AC R712 VRD-RA2BE100J J 10 1/8W Carbon AA R713 VRS-SV2HC122J J 1.2k 1/2W M-Ox. AA R715 VRD-RA2BE150J J 15 1/8W Carbon AA R716 VRS-VU3AE121J J 120 1W M-Ox. AB R721 VRD-RM2HD124J J 120k 1/2W Carbon AA R723 VRN-MD2AL000J J 0 1/10W M-Film AA R725 VRS-SV2HC821J J 820 1/2W M-Ox. AA
R733 VRD-RA2EE394J J 390k 1/4W Carbon AAR736 VRD-RM2HD184J J 180k 1/2W Carbon AA
R739 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R740 VRD-RM2HD470J J 47 1/2W Carbon AA
R741 VRD-RM2HD682J J 6.8k 1/2W Carbon AA
R751 VRD-RA2BE821J J 820 1/8W Carbon AA R752 VRD-RA2BE562J J 5.6k 1/8W Carbon AA R755 VRD-RM2HD151J J 150 1/2W Carbon AA
å R758 VRS-SV2HC150J J 15 1/2W M-Ox. AA
å R773 VRS-VU3LE270J J 27 3W M-Ox. AC
å R774 VRS-VU3LE680J J 68 3W M-Ox. AC
R801 VRD-RM2HD470J J 47 1/2W Carbon AA R807 VRN-MD2AL272J J 2.7k 1/10W M-Film AA R808 VRN-MD2AL272J J 2.7k 1/10W M-Film AA R809 VRN-MD2AL223J J 22k 1/10W M-Film AA R810 VRN-MD2AL223J J 22k 1/10W M-Film AA R901 VRD-RA2BE101J J 100 1/8W Carbon AB R902 VRN-MD2AL750J J 75 1/10W M-Film AA R906 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R925 VRN-MD2AL104J J 100k 1/10W M-Film AA R961 VRN-MD2AL101J J 100 1/10W M-Film AA R962 VRN-MD2AL101J J 100 1/10W M-Film AA R2001 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R2002 VRN-MD2AL103J J 10k 1/10W M-Film AA
27
Page 26
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-A: DUNTKA358WEV0 (13N-M100B/150B) PWB-A: DUNTKA358WEV3 (CN13M10B)
MAIN UNIT (Continued)
R2006 VRN-MD2AL103J J 10k 1/10W M-Film AA R2008 VRN-MD2AL333J J 33k 1/10W M-Film AA R2009 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R2010 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R2012 VRN-MD2AL103J J 10k 1/10W M-Film AA R2014 VRN-MD2AL103J J 10k 1/10W M-Film AA
(CN13M10B) R2016 VRN-MD2AL223J J 22k 1/10W M-Film AA R2018 VRN-MD2AL103J J 10k 1/10W M-Film AA
(13N-M100B/150B) R2020 VRN-MD2AL223J J 22k 1/10W M-Film AA R2022 VRN-MD2AL333J J 33k 1/10W M-Film AA R2023 VRD-RA2BE223J J 22k 1/8W Carbon AA R2024 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2025 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2026 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2027 VRD-RA2BE682J J 6.8k 1/8W Carbon AA R2028 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R2029 VRN-MD2AL103J J 10k 1/10W M-Film AA R2032 VRD-RA2BE471J J 470 1/8W Carbon AA R2033 VRN-MD2AL684J J 680k 1/10W M-Film AA R2034 VRN-MD2AL684J J 680k 1/10W M-Film AA R2040 VRN-MD2AL102J J 1.0k 1/10W M-Film AA R2041 VRN-MD2AL333J J 33k 1/10W M-Film AA R2042 VRD-RA2BE101J J 100 1/8W Carbon AB R2043 VRD-RA2BE101J J 100 1/8W Carbon AB R2044 VRN-MD2AL683J J 68k 1/10W M-Film AA R2045 VRN-MD2AL101J J 100 1/10W M-Film AA R2047 VRN-MD2AL221J J 220 1/10W M-Film AA R2048 VRN-MD2AL562J J 5.6k 1/10W M-Film AA R2049 VRN-MD2AL333J J 33k 1/10W M-Film AA R2060 VRN-MD2AL221J J 220 1/10W M-Film AA R2061 VRN-MD2AL562J J 5.6k 1/10W M-Film AA R2062 VRN-MD2AL183J J 18k 1/10W M-Film AA R2063 VRN-MD2AL222J J 2.2k 1/10W M-Film AA R2065 VRN-MD2AL000J J 0 1/10W M-Film AA R2066 VRN-MD2AL103J J 10k 1/10W M-Film AA R2067 VRN-MD2AL103J J 10k 1/10W M-Film AA R2068 VRN-MD2AL103J J 10k 1/10W M-Film AA R2070 VRN-MD2AL103J J 10k 1/10W M-Film AA R2072 VRN-MD2AL103J J 10k 1/10W M-Film AA R2101 VRN-MD2AL101J J 100 1/10W M-Film AA R2102 VRN-MD2AL101J J 100 1/10W M-Film AA R2201 VRD-RA2BE103J J 10k 1/8W Carbon AA R2202 VRD-RA2BE473J J 47k 1/8W Carbon AA R2203 VRN-MD2AL332J J 3.3k 1/10W M-Film AA R2211 VRD-RA2BE222J J 2.2k 1/8W Carbon AA R2212 VRN-MD2AL682J J 6.8k 1/10W M-Film AA R2213 VRD-RA2BE223J J 22k 1/8W Carbon AA R2401 VRN-MD2AL101J J 100 1/10W M-Film AA R2402 VRN-MD2AL101J J 100 1/10W M-Film AA R2403 VRN-MD2AL101J J 100 1/10W M-Film AA R2404 VRN-MD2AL101J J 100 1/10W M-Film AA R2501 VRN-MD2AL123J J 12k 1/10W M-Film AA R2503 VRN-MD2AL273J J 27k 1/10W M-Film AA R2504 VRN-MD2AL123J J 12k 1/10W M-Film AA R2505 VRN-MD2AL563J J 56k 1/10W M-Film AA R2506 VRN-MD2AL563J J 56k 1/10W M-Film AA R2507 VRN-MD2AL823J J 82k 1/10W M-Film AA R2508 VRN-MD2AL153J J 15k 1/10W M-Film AA R2509 VRN-MD2AL272J J 2.7k 1/10W M-Film AA R2601 VRD-RA2BE331J J 330 1/8W Carbon AA
or QSW-K0079GEZZ
S2504 QSW-K0202PEZZ R CH-Down AC
or QSW-K0079GEZZ
S2505 QSW-K0202PEZZ R CH-Up AC
or QSW-K0079GEZZ
MISCELLANEOUS PARTS
å F701 QFS-B4023CEZZ J Fuse 4A (125V) AC
or
QFS-B4021GEZZ FH701 QFSHD1013CEZZ J Fuse Holder AC FH702 QFSHD1014CEZZ J Fuse Holder AC FB351 RBLN-0047CEZZ J Ferrite Bead AB FB601 RBLN-0047CEZZ J Ferrite Bead AB FB2002RBLN-0037CEZZ J Ferrite Bead AB J903 QJAKE0205CE09 J Jack, Audio IN AD
or
QJAKE0159CEZZ J905 QJAKE0205CE04 J Jack, Video IN AD
or
QJAKE0158CEZZ P302 QPLGN0261CEZZ J Plug, 2-pin (S) AB P401 QPLGN0561CEZZ J Plug, 5-pin (GBN) AB P601 QPLGN0660CEZZ J Plug, 6-pin (K) AC P651 QPLGN0361CEZZ J Plug, 3-pin (TP651-3) AB P701 QPLGN0260CEZZ J Plug, 2-pin (M) AC P751 QPLGN0461CEZZ J Plug, 4-pin (YBN) AB P2001 QPLGN0561CEZZ J Plug, 5-pin (TP2001-5) AB
RMC2601
RRMCU0232CEZZ J R/C Receiver AG
or
RRMCU0252CEZZ RDA501
PRDAR0297PEFW R Heat Sink, for IC501 AD RDA701
PRDAR0026PEFW R Heat Sink, for Q701 AD
LX-BZ3100CEFD J Screw AA
S2501 QSW-K0202PEZZ R Power AC
SWITCHES
or QSW-K0079GEZZ
S2502 QSW-K0202PEZZ R VOL-Down AC
or QSW-K0079GEZZ
S2503 QSW-K0202PEZZ R VOL-Up AC
28
Page 27
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PWB-B: DUNTKA359WEV0 (13N-M100B/150B) PWB-B: DUNTKA359WEV3 (CN13M10B)
MISCELLANEOUS PARTS
CRT UNIT
å
ACC701
Q852 VSBF422////-1 J BF422 AC
TRANSISTORS
or VS2SC2229O/1E
Q854 VSBF422////-1 J BF422 AC
or VS2SC2229O/1E
Q856 VSBF422////-1 J BF422 AC
or VS2SC2229O/1E
Q881 VS2SA1266-Y-1 J A1266(Y) AA
or VS2SA1015-Y-1
å
QACCD3090CESA J AC Cord AK or (13N-M100B, CN13M10B) QACCD3064CESA or QACCD3060CESA
ACC701
QACCD3060CESB J AC Cord (13N-M150B) AR
SP1 VSP0080PBP8YA R Speaker, 32ohm AK
or VSP0080PBQ3YA QCNW-2105PEZZ R Connecting Cord AF QCNW-2106PEZZ R Connecting Cord AE QCNW-2107PEZZ R Connecting Cord AE
D882 RH-DX0475CEZZ J Diode AB
DIODES
D885 RH-DX0475CEZZ J Diode AB
COIL
L852 VP-MK820K0000 J Peaking 82µH AB
CAPACITORS
[EL.··· Electrolytic]
C851 VCCCCY1HH151J J 150p 50V Ceramic AA C852 VCCCCY1HH151J J 150p 50V Ceramic AA C853 VCCSPA1HL151J J 150p 50V Ceramic AA C854 RC-KZ0029CEZZ J 0.01 250V Ceramic AC
or
RC-KZ0160GEZZ C881 VCEA0A1CW106M J 10 16V EL. AB C883 VCEA0A1CW336M J 33 16V EL. AB
RESISTORS
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
R852 VRD-RA2BE221J J 220 1/8W Carbon AA R853 VRN-MD2AL121J J 120 1/10W M-Film AA
å R857 VRS-VU3AE123J J 12k 1W M-Ox. AB
R858 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R860 VRD-RA2BE221J J 220 1/8W Carbon AA R861 VRN-MD2AL121J J 120 1/10W M-Film AA
å R865 VRS-VU3AE123J J 12k 1W M-Ox. AB
R866 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R867 VRN-MD2AL470J J 47 1/10W M-Film AA R868 VRN-MD2AL221J J 220 1/10W M-Film AA R869 VRN-MD2AL121J J 120 1/10W M-Film AA
å R873 VRS-VU3AE123J J 12k 1W M-Ox. AB
R874 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R881 VRN-MD2AL561J J 560 1/10W M-Film AA R882 VRN-MD2AL391J J 390 1/10W M-Film AA R883 VRD-RA2BE561J J 560 1/8W Carbon AA R884 VRN-MD2AL152J J 1.5k 1/10W M-Film AA R886 VRN-MD2AL821J J 820 1/10W M-Film AA R887 VRD-RA2BE470J J 47 1/8W Carbon AA R890 VRN-MD2AL470J J 47 1/10W M-Film AA R891 VRN-MD2AL470J J 47 1/10W M-Film AA
SUPPLIED ACCESSORIES
RRMCG1324CESA J Infrared R/C Unit AT
(13N-M100B, CN13M10B)
RRMCG1324CESB J Infrared R/C Unit AT
(13N-M150B)
TiNS-7209PEZZ R Operation Manual AE
(13N-M100B/150B)
TiNS-7238PEZZ R Operation Manual
(CN13M10B)
P851 QPLGN0561CEZZ J Plug, 5-pin (GBN) AB
MISCELLANEOUS PARTS
P852 QPLGN0461CEZZ J Plug, 4-pin (YBN) AB SC852 QSOCV0839CEZZ J CRT Socket AK
or
QSOCV0842CEZZ
29
Page 28
13N-M100B/150B CN13M10B
Ref. No. Part No. Description Code Ref. No. Part No. Description Code
PACKING PARTS
(NOT REPLACEMENT ITEM)
SPAKC6619PEZZ – Packing Case (13N-M100B) — SPAKC6620PEZZ – Packing Case (13N-M150B) — SPAKC6633PEZZ – Packing Case (CN13M10B) — SPAKP0031PEZZ – Wrapping Paper — SPAKP0110PEZZ – Wrapping Paper — SPAKX2630PEZZ – Buffer Material — SSAKA0001PEZZ – Polyethylene Bag
CABINET PARTS
1 CCABA2552WEV0 R Front Cabinet Ass’y AX 1 CCABA2552WEV2 R Front Cabinet Ass’y AX 1 CCABA2566WEV0 R Front Cabinet Ass’y AZ 1-1
1-2 GCOVA0078PEKA R R/C Cover AD 1-3 JBTN-0306PESA R Button AD
1-3 JBTN-0306PESB R Button (13N-M150B) AD 2 CCABB2309WEV0 R Rear Cabinet (13N-M100B) AW 2 CCABB2309WEV1 R Rear Cabinet (13N-M150B) AW 2 CCABB2325WEV0 R Rear Cabinet (CN13M10B) AW
Not Available
(13N-M100B) (13N-M150B) (CN13M10B)
– Front Cabinet
(13N-M100B, CN13M10B)
1-1
1
2
1-2
1-3
30
Page 29
Wrapping Paper
13N-M100B/150B CN13M10B
PACKING OF THE SET
Polyethylene Bag
Operation Manual Batteries
FRONT
Buffer Material
Packing Case
Use 22 staples to fix the packing case.
REAR
MARK : Not replacement items.
31
Page 30
13N-M100B/150B CN13M10B
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
D SEM (13N-M150B) D JAP AN P SREC TQ1017-S
Nov. 2000 Printed in Japan
MI. KG
SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
32
Loading...