The RGB Slider is a compact midi-ATX case with a sleek look. While the PC case focuses on the essentials, it still has
some advantages to oer which set it apart from other cases in its class. Thanks to the black finish and its simple
form, it is pleasantly discreet and unassuming. However, the case also has highlights such as the side panel made of
tempered glass, the I/O panel with two USB 3.0 ports, and the RGB LED strip integrated in the front panel. If the
manual color control is used, the strip can be lit in 14 dierent lighting modes. Additional lighting elements can also
be added and customized via the built-in RGB controller. When it comes to internal installation options, the RGB
Slider also oers more than meets the eye.
Page 3
SIMPLE YET STYLISH
FRONT PANEL
The matte black front panel of the case is decorated
with an RGB LED strip which complements the minimalist look with flowing, luminescent colors. The strip
appears to be gently sliding across its middle, which is
where the case gets its name, and can be illuminated in
14 preset modes via the integrated RGB controller.
Alternatively, it can be customized through compatible
mainboards, using Asus Aura Sync, MSI Mystic Light
Sync, Gigabyte Fusion and ASRock Polychrome SYNC.
The built-in RGB controller also makes it possible
to use additional RGB components which have a
5V-D-coded-G or 5V-D-G pinout.
The RGB Slider case, along with all other Sharkoon
products marked with the "ADDRESSABLE RGB" logo,
are certified for Asus Aura Sync, MSI Mystic Light
Sync, Gigabyte Fusion and ASRock Polychrome SYNC.
These products are thus easy to incorporate into
existing systems.
Sharkoon products marked with the "ADDRESSABLE RGB" logo are compatible with mainboards which have headers for addressable RGB LED fans and strips. The headers should
have the pin configuration 5V-D-coded-G or 5V-D-G. Examples of these RGB connections
from the most important mainboard manufacturers are shown below. The RGB pin configuration is independent of manufacturer. However, the naming and marking of these connections may vary between manufacturers. For further information concerning compatibility,
refer to the manual of your mainboard, or visit the manufacturer's website.
MSIASUSASROCKASUSGIGABYTE
Page 4
2-PORT ADDRESSABLE
RESET SW
RGB CONTROLLER
The RGB Slider comes with a
preinstalled addressable RGB
controller. With compatible mainboards, this will function as a hub
for controlling and synchronizing
SATA
Addressable RGB LED
Fans / Strips
up to two addressable LED components, which will illuminate in up to
16.8 million colors. The controller is
connected to the power supply via a
SATA connector and to a mainboard
via a 4-pin or 3-pin header for
addressable LEDs with the pinout:
5V-D-coded-G or V-D-G.
V D G
IN
V D G
or
+5V DG
Mainboard Addressable
RGB Pin Header
MANUAL COLOR CONTROL
The RGB Slider also has a manual color control function for mainboards which
do not have headers for addressable LED components. With this, the RGB
controller is not connected to the mainboard, but rather connected to the
power supply and the reset switch of the PC case. The switch’s reset function
is then replaced with a new function which allows up to fourteen lighting
modes to be cycled through and selected, or, if desired, the lighting can be
turned o.
RESET SW
RedGreenBlueWhiteYellowCyan
RGB
Mode 7
RGB
Mode 6
RGB
Mode 5
RGB
Mode 4
RGB
Mode 3
RGB
Mode 2
Pink
RGB
Mode 1
SATA
V D G
IN
Addressable RGB LED
Fans / Strips
Page 5
A CRYSTAL-CLEAR
PRESENTATION FOR HARDWARE
An unobstructed view of the installed hardware is possible through the left side. This is ensured by the side panel of the case, which
is made entirely of tempered glass. Your own build can thus be properly showcased inside the minimalist case. So that nothing
obscures the view, and the built-in components come into their own, there are no visible screws on the side panel. The attachment
is at the rear of the case and therefore out of the field of view.
Page 6
SUITABLE FOR LARGER
HARDWARE COMPONENTS
40.0 cm
15.7 cm
Max. Length
45.6 cm
Graphics Card: 31.0 / 33.5 cm*
SSD
With its compact size, the RGB Slider
can be easily integrated into smaller
setups or ones that are kept intentionally minimalist. Nevertheless, larger
hardware components can also be
easily installed in the case. The CPU
cooler can be up to 15.7 cm in size,
which leaves enough space for
graphics cards up to 33.5 cm long.
SSD
SSD
* Without front fan
2-Port Addressable
RGB Controller
HDD/SSD
HDD/SSD
Max. Length
Power Supply: 17.5 cm
Removable HDD/SSD Cage
Page 7
OPTIMAL AIR
INTAKE POSSIBILITIES
1x
120 mm Fan
(Pre-Installed)
3x
120 mm Fans
(Optional)
2x 120 mm Fans (Optional) or
2x 140 mm Fans (Optional)
Magnetic, Easy-to-Clean
Dust Filter on Top Panel
Removable Dust Filter
on the Bottom Panel
Easily Accessible Top I/O
Tempered Glass
The RGB Slider is designed to oer sucient installation possibilities to ensure optimal airflow. A 120 mm fan is pre-installed at the back of the case, ready to discharge warm air outside. If desired, more fans can be installed within the
case: There is room behind the front panel for up to three optional 120 mm fans. Two 120 mm fans or two larger 140 mm
fans can also be installed under the top panel. A 120 mm fan can also be installed on the tunnel to further cool the
storage drives.