Shark Transformer Vac EP602 Owner's Manual

OWNER’S MANUAL
Model EP602

120V., 60Hz., 10 Amps

EURO-PRO Operating LLC

Boston, MA, 02465
Tel.:

1 [phone]

www.sharkvac.com

COPYRIGHT© EURO-PRO OPERATING LLC 2008

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

1

For Household Use Only

Rev. 10/07C

To reduce the risk of fire, electric shock, or
injury:

• Do not leave the Transformer Vac plugged
in when unattended. Unplug the electrical
cord when not in use and before servicing.

• Do not allow the vacuum to be used as a
toy. Close attention is necessary when
used by or near children, pets or plants.

• Use only as described in this manual. Use
only manufacturer’s recommended
accessories.

• Do not pull cord, use cord as a handle,
close a door on cord, or pull cord around
sharp edges or corners. Keep cord away
from heated surfaces.

•Use only extension cords UL-rated or cUL
at 15 amperes. Extension cords rated for
less amperage may overheat. Care should
be taken to arrange the cord so that the cord
cannot be pulled or tripped over.

• Turn off all controls as applicable before
unplugging from electrical outlet.

• Do not handle plug or vacuum with wet
hands or operate without shoes.

• Do not put any objects into openings. Do
not use with any opening blocked. Keep
free of dust, lint, hair and anything else that
may reduce air flow.

• Store your appliance indoors in a cool, dry
area.

• Keep your work area well lit.

• Keep end of hose, wands and other
openings away from your face and body.

• Use only on dry surfaces.

• Using improper voltage may result in
damage to the motor and possible injury to
the user. Correct voltage is listed on rating
label.

When using your Transformer Vac basic safety precautions should always be observed, including
the following:

1. Read all instructions before using your
Transformer Vac.

2. Use the system only for its intended use.

3. To protect ag ain st a risk of electric shock,
do not immerse any part of the system in
water or other liquids.

4. Never yank cord to disconnect from
outlet; instead, grasp plug and pull to
disconnect.

5. Do not allow cord to touch hot surfaces.

6. Do not run appliance over cord.

7. Do not operate the system with a
damaged cord or plug, or if the appliance
or any other part of the system has been
dropped or damaged. To avoid the risk of
electric shock, do not disassemble or
attempt to repair the Transformer Vac.
Return the system to EURO-PRO
Operating LLC (see warranty) for
examination and repair. Incorrect
re-assembly or repair can cause a risk of
electrical shock or injury to persons when
the Transformer Vac is used.

8. Close supervision is necessary for any
appliance being used by or near children.
Do not leave the system unattended while
connected.

9. Keep hair, loose clothing, fingers and all
parts of body away from opening and
moving parts.

10. Do not use to pick up flammable or
combustible liquids such as gasoline or
use in areas where they may be present.

11. Do not pick up anything that is burning or
smoking such as cigarettes, matches or
hot ashes.

12. Use extra care when cleaning on stairs.

13. Do not use the vacuum without ALL the
filters in place.

14. This appliance is intended only for
household use. Follow all user
instructions in this manual.

WARNING: To reduce the risk of electric shock, this appliance has a polarized
plug (one blade is wider than the other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet.
Do not modify the plug in any way.

2

GETTING TO KNOW YOUR TRANSFORMER VAC

Technical Specifications

Voltage: 120V., 60Hz.
Power: 10 Amps

1. Hand Grip

2. Telescopic Tube

3. Locking Button

4. Flexible Hose

5. Dust Cup Release Button 1

6. Dust Cup Handle

7. Dust Cup (Container)

8. Main Unit

9. Intelli-Sense

TM

Filter

Monitor

10. Exhaust Filter Cover

11. On/Off Switch

12. Power Cord

13. Floor Brush Release Button

14. Floor Brush

15. Crevice Tool

16. Dusting Brush

17. Telescopic Tube Release
Button

18. Dust Cup Release Button 2

19. Cord Hook Release

20. Hose Connector

21. Shoulder Strap (not shown)

22. Air Driven Turbo Brush

22

Note: Illustrations may differ from actual unit.

PRECAUTIONARY MEASURES

IMPORTANT: If the suction opening in the unit or the hose is BLOCKED, switch off

the vacuum cleaner and remove the blocking substance before you
start the unit again.

1. Do not operate the vacuum cleaner
too close to heaters, radiators or
cigarette butts.

2. Before inserting the power plug into
the wall outlet, make sure that your
hands are dry.

4. When pulling out the power plug
from the wall outlet, pull the plug not
the power cord.

3. Before you start vacuuming, make
sure to remove large or sharp objects
that might damage the dust cup
debris screen.

5. Do not pick up anything that is
burning or smoking such as
cigarettes, matches or hot ashes.

6. Do not use without ALL filters in
place.

3

OPERATING INSTRUCTIONS

WARNING: Always remove the power

plug from the wall outlet before
assembling or removing accessories.

INSERTING THE TELESCOPIC
TUBE INTO THE MAIN UNIT

• Insert the telescopic tube into the hole
next to the dust cup handle. Make
sure that the slot in the handle fits
correctly into the opening. (Fig. 2)

• To remove the telescopic tube, press
the telescopic tube release button and
pull the tube up.

EXTENDING THE TELESCOPIC
TUBE

Push the plastic button and pull out the
smaller tube. (Fig. 1)

ATTACHING THE FLOOR BRUSH
TO THE MAIN UNIT

• Insert the floor brush into its location,
in the direction of the arrow. (Fig. 3)

• To remove the floor brush from the
main unit, press on the floor brush
release button and pull the floor brush
out.

ATTACHING THE HOSE TO THE
MAIN UNIT

• Hold the end of the hose.

• Insert the hose into the hose
connector. (Fig.4)

4

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 7

OPERATING INSTRUCTIONS

WINDING & UNWINDING THE
POWER CORD

This vacuum cleaner is
equipped with a convenient
cord storage feature. The
power cord winds around
the two cord holders at
the back of the unit. The
bottom one has a quick
cord release feature.
Turn the cord hook to
the left or the right to
remove the power cord.
(Fig. 5)

ON/OFF SWITCH

• The On/Off switch has two different
positions.

• Push on the "I" side to turn the
vacuum ON.

• Push on the "O" side to turn the
vacuum OFF.

USING THE UNIT AS A HAND
VACUUM

• Press the telescopic tube release
button to remove the telescopic tube.
(See Fig. 2 page 4)

• Press the floor brush release button to
remove the floor brush. (See Fig 3
page 4)

• Attach the shoulder strap to the
shoulder strap attachment point.
(Fig. 6)

• Attach the crevice tool or the dusting
brush to the end of the hose.

Crevice Tool

For radiators, crevices, corners,
baseboards and
between cushions.

Dusting Brush

The dusting brush is
used for the furniture,
venetian blinds,
books, lamp shades
and shelves.

5

= OFF

= ON

USING THE UNIT AS AN UPRIGHT

• Unwind the power cord
and plug into the
120V outlet.

• Push down on the
locking button to adjust
the height of the
telescopic handle.

NOTE: When vacuuming

deep pile carpets or
hard to vacuum
carpets, lower the angle
of the telescopic
handle (see
illustration at
right) for
easier
maneuverability.

L

o

w

e

r

WARNING

After extended use, the body of the
vacuum cleaner may become hot.
When using the unit with the shoulder
strap, the unit will touch the body of
the user. Therefore, make sure that
the unit body is cool before you use
with the shoulder strap. If during use,
the vacuum gets too warm, allow it to
cool before continuing to use.

When the Intelli-Sense

TM

Filter
Monitor lights up, it means that the
dust cup is full or the HEPA filter,
non-woven pre-filter or debris
screen needs cleaning. You must
empty the dust from the dust cup
and clean the HEPA filter, non­woven pre-filter and debris screen
right away.

Intelli-SenseTMFilter Monitor

OPERATING INSTRUCTIONS

6

Turbine

Tilt
Upwards

Locking Latch

From time to time, the turbine of your
turbo brush will require cleaning. To do
this:

1. Remove the turbo brush from the
hose or telescopic extension tube.

2. Slide locking latch forward then tilt the
top housing of the brush upwards.
The top housing is hinged and will tilt
up approximately 45° only.

3. There may be some dust, lint, hair,
etc on the turbine wheel. Remove as
much of this as possible.

4. You may also use the unit’s hose with
crevice tool attached and use the
vacuum to remove any additional
debris from the turbine.

5. Ensure that the turbine wheel moves
freely by rotating it with your finger. If
the turbine does not rotate, call
Customer Service for help.

6. Once clean, close the top cover of the
turbo brush and slide the locking latch
toward the rear of the brush to lock.

Attaching the Air Driven Turbo
Brush to the Flexible Hose

To use the air driven turbo brush to
clean upholstery:

1. Remove the flexible hose from the
hose connector. (Fig. 7)

2. Push the air driven turbo brush onto
the end of the flexible hose as far as
it will go.

Cleaning Air Driven Turbo Brush

Using The Unit With Air Driven
Turbo Brush

The efficiency of your air driven turbo
brush depends on the bristle brush
rotating at high speed. Strong air suction
is needed to accomplish this. In order to
ensure that maximum air suction is
maintained, please read the following
instructions:

1. Empty the dust cup frequently.

2. Always shake out the HEPA filter and
clean the non-woven pre-filter and the
debris screen when emptying the dust
cup container.

3. Ensure that the rotating brush is kept
free of hair and string which may
accumulate and decrease brush
performance.

4. Keep air driven turbo brush turbine
free of dirt and foreign matter. (See
illustration for cleaning instructions.)

Air Driven Turbo Brush

Important: In order to ensure that

maximum air suction is maintained,
empty the dust cup frequently and shake
out the HEPA filter and clean the non­woven pre-filter and debris screen at the
same time. Ensure that the rotating
brush is kept free of hair and string which
may accumulate and decrease brush
performance.

Fig. 5

Fig. 6

Fig. 13

7

OPERATING INSTRUCTIONS

Emptying the Dust Cup Container
and Cleaning / Changing the Non­Woven Pre-Filter, HEPA Filter &
Debris Screen

Important: Do NOT use the vacuum

without the HEPA filter in place.

IMPORTANT

, Please Note: The

“TapClean” HEPA filter will stop most of
the microscopic dust particles and
airborne allergens from re-entering the
air you breathe. Because of this
incredible filtration performance, the
HEPA filter will quickly accumulate,
inside the white filter folds, many fine
dust particles that are difficult to see but
which will eventually block or reduce your
suction power - if not cleaned properly.

1.To remove the dust cup container,
first press on the dust cup release
button (1) that is located on the dust
cup handle and at the same time
press on the dust cup release button
(2) that is on the side of the upper
housing. (Fig. 8) Then pull the dust
cup container out.

4.Hold the HEPA filter
by the edges and vigorously
“TapClean” the HEPA Filter
dirty side down on a hard,
flat surface until no more
dust is observed falling out
from between the pleats of
the filter. (Fig. 12) We
recommend washing the HEPA filter
once a month or when suction
appears to be reduced. Let the HEPA
filter air dry completely for 24 hours.

5.Rinse the non-woven pre-filter and let
it air dry completely for 24 hours.

6.Insert the non-woven pre-filter.

7.Reinstall the HEPA filter in the
vacuum.

8.To separate the debris screen from
the dust cup, hold the dust cup in one
hand and turn the
dust cup cover counter
clockwise and pull apart.
To clean the
debris screen, we
recommend that
you rinse it under
lukewarm running
water to remove the dirt that
accumulates on it, but always allow it
to completely air dry before inserting
back into the vacuum. (Fig. 13)

Warning: Always unplug the

unit from electrical outlet before
opening the Dust Cup (container).

Warning: After each Use -

Always remove filter assembly
and the dust cup cover with the
debris screen, then vigorously
“TapClean” HEPA filter and clean
debris screen and non-woven
pre-filter until no more dust can
be removed.

Fig. 9

Fig. 10

Fig. 12

Dust Cup

Release
Button 2

Dust

Cup
Release
Button 1

Fig. 8

HEPA
Filter

Non-Woven
Pre-Filter

Fig. 11

2. To empty the dust cup
container, press on the
trap door release button
that is on the back side
of the dust cup
container. (Fig. 9)

3. The HEPA filter is
located underneath the
dust cup container.
(Fig.10) Remove the non-woven pre­filter. (Fig. 11) Remove the HEPA
filter, hold the edges and pull it out
slowly.

Wash
once a
month or
when
suction
appears
reduced

Fig. A

8

Pre-Motor
Filter

Warning: Allow 24

hours for drying before
replacing in unit.

Never over fill the dust cup container ­remove dirt and clean the HEPA filter, non­woven pre-filter and debris screen when dirt
in dust cup is at or below the "MAX" level
during prolonged usage or risk motor
damage.

If you wash the HEPA filter or the non­woven pre-filter, make sure that they
have completely air dried before
inserting back in the vacuum.
Please Note:

The HEPA Filter is washable.
It should, however, be replaced every three
(3) to six (6) months to ensure peak
performance of your vacuum.
The non-woven pre-filter, pre-motor and
post motor filters are washable.

Important: Make sure that ALL filters

have completely air dried before re­installing back in the vacuum.

Warning: Always empty the dust cup

container and clean the HEPA filter,
non-woven pre-filter and debris screen
before each use and during prolonged
usage.

CAUTION: The suction hole must be

open, free of any obstructions at all
times. Otherwise, the motor will
overheat and could become damaged.

Fig. 14

Fig. 15

Changing & Cleaning the Post
Motor Filter

The post motor filter is a washable filter.

• Remove the filter cover from the front
of the unit and remove the filter.
(Fig. 15)

• Rinse the post motor filter in lukewarm
water and air dry the filter completely
for 24 hours. Do not use a washing
machine to rinse the filter. Do not
use a hair dryer to dry it. Air dry only.
Never operate the vacuum without the
post motor filter in place.

• When the filter is dry,
replace into the filter
cover and replace the
filter cover to the unit.

• A severely soiled or
clogged filter should
be thoroughly
washed with
lukewarm water.
A mild detergent can be
used if required.

OPERATING INSTRUCTIONS

Changing & Cleaning the Pre­Motor Filter

The pre-motor filter is a washable filter.

• Remove the dust cup container, the
non-woven pre- filter and the HEPA
filter to remove the pre-motor filter.
(Fig 14)

• Rinse the pre-motor filter in lukewarm
water and air dry the filter completely
for 24 hours. Do not use a washing
machine to rinse the filter. Do not use
a hair dryer to dry it. Air dry only.
Never operate the vacuum without the
pre-motor filter in place.

• When the filter is dry, replace into the
unit and replace the HEPA filter and
dust cup container.

• A severely soiled or clogged filter
should be thoroughly washed with
lukewarm water. A mild detergent can
be used if required.

PLEASE NOTE

: The white pleated filter
material in the HEPA filter will discolor over
time -This is NORMAL and will NOT affect
the performance of the filter. If the HEPA
filter is properly
"TapCleaned”
after each use
and suction
does not return
to 100%, then
we suggest that
the HEPA filter
be “TapCleaned”
vigorously until
no more dust
can be removed,
then rinsed under the faucet and allowed to
dry for 24 hours before refitting into the
vacuum. (Fig. A) This should be done

once a month or when suction appears
to be reduced.

TROUBLE SHOOTING GUIDE

OPERATING INSTRUCTIONS

IMPORTANT: This unit is equipped

with a motor protective thermostat. If
for some reason the vacuum cleaner
should overheat, the thermostat will
automatically turn the unit off. Should
this occur:

• Push the On/Off button once.

• Disconnect the plug from the
power source.

• Check the source of overheating
problem. (i.e. clogged hose or
filter)

Motor Thermostat

• If clogged hose or filter is found,
unclog the hose and replace the
filters.

• Wait at least 45 minutes before
attempting to reuse the vacuum.

• After unit has cooled down for
45 minutes, plug in the cleaner
and push the On/Off button. The
vacuum should start again.

• If the vacuum still does not start,
contact customer service at
1 [phone].

9

PROBLEM POSSIBLE REASON POSSIBLE SOLUTION

VACUUM WILL
NOT OPERATE

1. Power cord not firmly plugged into
outlet.

2. No power in wall outlet.

3. Needs servicing.

4. Thermostat has tripped.

1. Plug unit in firmly.

2. Check fuse or breaker. Replace
fuse/reset breaker.

3. Call 1 [phone].

4. Turn the unit off and unplug from
outlet. Allow unit to cool down,
then restart.

VACUUM WILL
NOT PICK-UP OR
SUCTION POWER
IS WEAK

1. Dust cup is full.

2. Unit clogged.

3. HEPA Filter needs cleaning or
replacing.

4. Debris screen needs cleaning.

5. Filters need cleaning

1. Empty and clean dust cup.

2. Turn unit off and unplug from wall
outlet. Remove Dust Cup Filter
and check for object(s) in air duct
and remove.

3. Clean or replace HEPA Filter.

4. Clean debris screen.

5. Clean Filters

TURBO BRUSH
DOES NOT
ROTATE OR
ROTATES
SLOWLY

1. Dust cup is full.

2. Rotating brush or elbow is
obstructed.

3. Belt is broken.

4. Hose obstructed.

5. Debris screen is clogged.

6. Filters need cleaning.

1. Empty dust cup.

2. Clear obstructions.

3. Call 1 [phone].

4. Clear obstruction.

5. Clean debris screen.

6. Clean All filters.

DUST ESCAPING
FROM VACUUM

1. Dust cup is full.

2. Dust cup is not installed correctly.

1. Empty and clean dust cup.

2. Review Dust cup instructions.

VACUUM, HOSE
OR BRUSHES
WILL NOT PICK-UP

1. Hose clogged.

2. Dust cup is full.

1. Remove hose and/or brushes.
Remove obstruction from hose
and/or brush.

2. Empty and clean dust cup.

Please Note:

The HEPA Filter is washable. It should, however, be replaced every three (3)
to six (6) months to ensure peak performance of your vacuum.

The Pre-Motor, the Non-Woven Pre-Filter and Post Motor Filters are
washable.

Important:

Make sure that ALL filters have been completely air dried for 24 hours before
re-installing back in the vacuum.

ORDERING REPLACEMENT DUST CUP FILTERS

TO ORDER REPLACEMENT HEPA FILTERS

Item # XSH602

for Model EP602

Call: 1 [phone]

Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

or

visit our website: www.sharkvac.com

FOR TECHNICAL SUPPORT

for Model EP602

Call: 1 [phone]

Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time

10

ONE (1) YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from defects in material and
workmanship for a period of one (1) year from the date of the original purchase, when utilized for
normal household use, subject to the following conditions, exclusions and exceptions.

If your appliance fails to operate properly while in use under normal household conditions within the
warranty period, return the complete appliance and accessories, freight prepaid. For Customer
Service support, call 1 [phone] or visit our website at www.sharkvac.com.

If the appliance is found by EURO-PRO Operating LLC to be defective in material or workmanship,
EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and $ 9.95
to cover the cost of return shipping and handling must be included. * Non-durable parts including,
without limitation, filters, brushes and electrical parts which normally require replacement are
specifically excluded from warranty.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of
the unit at our option. This warranty does not cover normal wear of parts and does not apply to any
unit that has been tampered with or used for commercial purposes. This limited warranty does not
cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or
mishandling in transit. This warranty does not cover damage or defects caused by or resulting from
damages from shipping or repairs, service or alterations to the product or any of its parts, which have
been performed by a repair person not authorized by EURO-PRO Operating LLC.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or
conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the
specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever.
Some states do not permit the exclusion or limitation of incidental or consequential damages, so the
above may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state or province to province.

*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of
purchase date and to attach tag to item before packing with your name, complete address and
phone number with a note giving purchase information, model number and what you believe is
the problem with item. We recommend you insure the package (as damage in shipping is not
covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefor e the specifications
contained herein are subject to ch ang e w i thout notic e .

OWNERSHIP REGISTRATION CARD

FOR CANADIAN CONSUMERS ONLY

Please fill out and mail the product registration card within ten (10) days of purchase. The registration
will enable us to contact you in the unlikely event of a product safety notification. By returning this
card you acknowledge to have read and understood the instructions for use, and warnings set forth in
the accompanying instructions.

RETURN TO: EURO-PRO Operating LLC, 4400 Bois Franc, St. Laurent, Quebec, H4S 1A7

______________________________________________________________________

Appliance model

______________________________________________________________________

Date purchased Name of store

______________________________________________________________________

Owner’s name

______________________________________________________________________

Address City Prov. Postal code

Printed in China

Model EP602

11

Model EP602