Page 1
SV769UK
OWNER’S GUIDE
www.sharkclean.eu
Page 2
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK® CORDLESS HAND
VACUUM, BASIC SAFETY PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING YOUR
SHARK® CORDLESS HAND VACUUM.
WARNING:
This appliance is not intended for use by
persons with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for their
safety.
Children shall not use or play with this appliance.
Close supervision is necessary to keep appliance
out of reach of children during use.
This appliance complies with the WEEE-Directive
2012/19/EU on the disposal of electrical and
electronic equipment (WEEE).
This marking indicates that this product should
not be disposed with other household wastes
throughout the EU. To prevent possible
harm to the environment or human
health from uncontrolled waste
disposal (especially the battery),
recycle it responsibly to promote the
sustainable reuse of material sources.
To return your used device, please use the return
and collection systems or contact the retailer where
this product was purchased. They can take this
product for environmental safe recycling.
This appliance complies with the European directives
for electromagnetic compatibility (EMC) 2004/108/
EC and its revisions, as well as Low Voltage Directive
(LVD) 2006/95/EC and its revisions.
GENERAL ELECTRICAL SAFETY:
W
ARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY
DO NOT USE OUTDOORS OR ON WET SURFACES.
1 DO NOT use or charge the unit outdoors.
2 DO NOT use or charge the unit on wet surfaces.
3 DO NOT immerse vacuum cleaner or charging
adapter in water or other liquids.
4 DO NOT handle vacuum or charging adapter with
wet hands.
5 DO NOT use charging adapter if power cord has
been damaged.
6 DO NOT abuse the charging adapter cord.
NEVER carry the charging adapter by the cord.
7 DO NOT unplug the charging adapter by pulling on
cord; to unplug, grasp the plug, not the cord.
8 DO NOT use charging adapter with an extension
cord. Plug adapter directly and only in a standard
(220-240V~, 50/60Hz) electrical outlet.
9 DO NOT run the vacuum over the charging
adapter cord.
10 Keep charging adapter cord away from
heatedsurfaces.
11 DO NOT attempt to use the charging adapter
with any other product nor attempt to charge this
product with another charging adapter.
12 Only use charging adapter model number
XB769N provided.
13 Always turn the vacuum off before connecting or
disconnecting the motorized floor brush or crevice tool.
GENERAL USE:
14 Use only on dry, indoor surfaces.
15 Store the cordless vacuum indoors. Put the cordless
vacuum away after use to prevent accidents.
16 Use only as described in this manual. DO NOT use for
any purpose other than described in this user’s guide.
2 0800 862 0453
Page 3
17 Use only cleaning attachments supplied with this unit.
18 Keep your work area well lit.
19 Keep the vacuum moving over the carpet surface
at all times to avoid damaging the carpet fibers.
20 DO NOT put any objects into openings.
21 DO NOT use with any opening blocked; keep free of
dust, lint, hair and anything that may reduce airflow.
22 DO NOT use the vacuum cleaner without dust cup
and filter in place.
23 DO NOT vacuum up any liquids.
24 DO NOT pick up anything that is burning or
smoking such as cigarettes, matches or hot ashes.
25 DO NOT use to pick up flammable or combustible
liquids such as gasoline or use vacuum in areas
where their fumes may be present.
26 DO NOT pick up toxic solutions such as chlorine
bleach, ammonia or drain cleaner.
27 DO NOT use in an enclosed space where vapors
are present from paint, paint thinner, mothproofing substances, flammable dust or other
explosive or toxic materials.
28 DO NOT pick up hard or sharp objects such as
glass, nails, screws or coins that could damage
the vacuum cleaner.
29 DO NOT allow the vacuum to be used as a toy.
30 Close attention is necessary when used by or
nearchildren.
31 DO NOT use cordless vacuum cleaner or charging
adapter if it has been dropped, damaged, left outdoors
or submerged in water. To avoid the risk of electric
shock, do not disassemble or attempt to repair the
appliance on your own. If the supply cord is damaged,
it must be replaced by a qualified electrician in order
to avoid a hazard. Incorrect re-assembly or repair can
cause a risk of electrical shock or injury to persons
when the appliance is used.
32 Keep hair, face, loose clothing, fingers and all
body parts away from openings and moving parts.
33 This product is powered by Ni-Mh batteries, which
must be recycled when the replaceable battery
or leaking battery or battery pack is at the end
of its life. The battery must be removed from the
appliance before it is recycled. The appliance must
be disconnected from the supply when removing
the battery. Do not incinerate batteries or expose
to high temperatures, as they may explode.
Please ensure you deliver the battery for recycling
to the battery collection system in your country.
34 Leaks from battery cells can occur under extreme
conditions. If the liquid gets on the skin - wash
immediately with soap. If the liquid gets into the
eyes, flush them immediately with clean water for a
minimum of 10 minutes and seek medical attention.
35 The battery must be removed from the appliance
before it is discarded.
36 Batteries are to be recycled or disposed of safely.
37 Use extra care when cleaning on stairs.
38 Before turning on the vacuum:
•Makesurethatthedustcupandlterare
securely in place after routine maintenance.
•Makesurethatallcomponentsandltersare
thoroughly dry after routine cleaning.
•Onlyuseltersandaccessoriesprovidedby
EURO-PRO Operating LLC. [Failure to do so
will void the warranty.]
SAVE THESE
INSTRUCTIONS
DUST CUP/FILTER:
3www.sharkclean.eu
Page 4
MAXIMIZING THE LIFE OF YOUR BATTERY
WARNING: Never use ordinary batteries for
replacement as these may leak and damage
your vacuum cleaner. Use only the battery
pack XB769N provided by EURO-PRO Operating
LLC for replacement. Call customer service
at 0800 862 0453 or visit our web site at
www.sharkclean.eu to order replacement
batteries.
CAUTION:
• UseONLYwithbatterypacksupplied.DONOT
attempt to use non-rechargeable batteries.
• Donotattempttoremovethebatterypackfrom
the unit tocharge.
• Neverthrowthebatterypackortheappliance
into a fire or incinerate it.
• Donotremoveordamagethebatterycasing.
• Donotplacethebatteriesonmetalsurfaces.
• Donottouchmetalpartsofthebatteries
together as the batteries will overheat.
Technical Specifications
Battery
Voltage 16.8 VDC
Type Ni-MH
Weight 0.345 kg
Charger
Model Number ZD6W210024**1
Input Voltage 100-240 VAC
Output Voltage 21 VDC
Current 240 mA
Approximate Charge Time 8 hours
Weight 0.08 kg
BATTERY PACK DISPOSAL AND REPLACEMENT
The cordless hand vacuum is powered by Ni-MH
batteries, which must be recycled or disposed of properly
in accordance with state, federal and local laws. If
uncertain as to how to remove the battery pack, we
suggest that you take your hand vacuum to a reputable
small appliance service technician to have this service
performed. Do not attempt to replace the batteries used
in this product with any other type of battery. Follow these
steps when replacement of the battery pack is required:
1 Using a #1 Phillips head screwdriver, remove the
single screw securing the battery compartment cover
located underneath the unit.
2 Use a flathead screwdriver to remove the battery
compartment cover. Never open the battery
compartment except to replace the battery pack. Set
the cover and the screw aside.
3 Slide the battery strap over and lift it out.
4 Carefully lift out the battery pack and disconnect the
terminals.
5 Before inserting the new battery, connect the
terminals to the battery pack taking care to connect
the black lead (-) to the negative connector first and
the red lead (+) to the positive connector second.
6 Insert the new battery inside the battery
compartment.
7 Take care to tuck the wiring completely in so
that the wiring does not interfere with the battery
compartment cover when it is replaced.
8 Replace the battery strap by pushing it in all the way.
The battery strap only goes in one way.
9 Replace the battery compartment cover. The holes
for the screw from the battery strap and battery
compartment cover must be aligned.
10 Replace the screw, making sure not to over-tighten it.
Call customer service at 0800 862 0453 or visit our web site at
www.sharkclean.eu to order replacement battery packs.
4 0800 862 0453
Page 5
AS S E M B LY
a
b
c
e
g
f
d
h
j
i
VACUUM COMPONENTS
a On/Off Switch
b Charging Indicator Light
c Dust Cup Release Button
d Motor Housing
e Dust Cup Container
f Motorized Brush
g Crevice Tool
h Dusting Brush
i Charging Stand
j Charging Adapter- UK
5www.sharkclean.eu
Page 6
AS S E M B LY
Fig. 1 Fig. 2
Fig. 3 Fig. 4
ASSEMBLY
IMPORTANT: The dust cup filter must always be
in place when operating the hand vacuum.
1 Push the dust cup release button and remove the
dust cup. (fig. 1)
2 Verify that the dust cup filter is inside, then
reattach the dust cup to the hand vacuum. (fig. 2)
3 The motorized brush can be used to vacuum
short pile carpets or rugs. To attach the motorized
brush, make sure the On/Off switch is in the Off
position. Then firmly insert the motorized brush
into the air-intake nozzle, ensuring that the
contact pins are engaged in the connector slots of
the unit. (fig. 3)
WARNING: Do not touch the motorized brush
while it is in motion.
4 The crevice tool can be used to clean narrow, hard
to reach places. The dusting brush is used for the
furniture, venetian blinds, books, lamp shades and
shelves. Attach the desired attachment by pushing
it into the air-intake nozzle. (fig. 4)
Fig. 5
Fig. 6
ASSEMBLING THE CHARGING BASE
1 Insert the charge adapter plug through the hole in
the underside of the charging base / wall mounting
bracket. (fig. 5)
2 Turn the charge adapter plug one quarter turn to
secure it into place. (fig. 5)
CHARGING BASE / WALL MOUNTING BRACKET
1 If you wish to mount the charging base onto a
wall, make sure that the intended wall area that
is to be drilled is free from any hidden electrical
wires, water pipes and gas lines.
2 Select an appropriate place that is close to an
electrical outlet. Do not mount near direct sunlight,
near a heat source or outdoors.
3 Select an appropriate drill type for the material to
be drilled.
4 Carefully measure and mark the location of all
bracket holes and then drill holes and screw the
charging base / wall mounting bracket onto the
wall. (Screws not included.) (fig. 6)
6 0800 862 0453
Page 7
CHARGING
Fig. 7 Fig. 8
USAGE
ON
OFF
Fig. 9
CHARGING YOUR HAND VACUUM
1 Plug the charger into the wall outlet. Place the unit
in the charging base. The charging indicator light
will illuminate to show that the vacuum is being
charged. (fig. 7, fig. 8)
2 Before first using the hand vacuum, make sure
that the On/Off switch is in the “Off” position and
charge it for 20 hours.
3 After the initial charge, the charge time is 16 hours.
4 Always unplug the unit when the charge time is
complete.
USING THE CORDLESS VACUUM
CAUTION: The air-intake nozzle and
attachments must be free of obstructions at
all times, otherwise the motor will overheat
and could become damaged.
1 To start the vacuum, push the “On/Off” switch to
the “On” position. (fig. 9)
2 To turn the vacuum “Off”, push the “On/Off”
switch to the “Off” position. (fig. 9)
7www.sharkclean.eu
Page 8
CARE AND MAINTENANCE
REPLACEMENT PARTS
Fig. 10
Fi g. 11
CHANGING & CLEANING THE DUST CUP FILTER
NOTE: It is recommended that the dust cup filter
be replaced every three (3) months to ensure peak
performance of the vacuum. See PARTS section for
information on ordering replacement filters.
1 Press the dust cup release button and pull out the
dust cup.
2 Carefully remove the dust cup filter and empty the
dust from the dust cup. (fig. 10)
3 Rinse the dust cup filter in cold water and let it
dry completely before replacing back into the dust
cup. Do not wash it in a washing machine or use a
hair dryer to dry it. Air dry only! (fig. 11)
8 0800 862 0453
REPLACEMENT PARTS
XF769 Dust Cup Filter
XB769N Battery pack
®
To order additional parts for your Shark
VACUUM model SV769UK go to www.sharkclean.eu
or call 0800 862 0453.
CORDLESS HAND
Page 9
TROUBLESHOOTING GUIDE & GUARANTEE
PROBLEM SUGGESTED SOLUTION
The hand vacuum will not
operate
Motorized brush will not
work
Hand vacuum will not pick up
or suction is weak
Dust is escaping from the
hand vacuum
• Batteries need to be recharged.
• Batteries are dead and need to be replaced.
• There is no power in the electrical outlet being used while charging. Try
to charge using a different electrical outlet.
• The metal contact pins on the motorized brush are not in contact with
the connector slots on the vacuum. Remove the motorized brush and
re-insert firmly into the air-intake nozzle.
• The motorized brush is blocked. Carefully remove all the lint, hair, etc.
from the motorized brush.
• Dust cup is full. Empty the dust cup.
• Dust cup filter needs cleaning or replacement. Clean or replace the dust
cup filter.
• Vacuum needs to be recharged.
• Empty the dust cup container.
• The dust cup filter is not installed correctly. Remove it and re-insert it.
• The dust cup filter has a hole or a puncture in it. Replace it with a new one.
GUARANTEE
This product is unconditionally guaranteed for one year against all defects of workmanship and materials. This guarantee
does not affect your statutory rights. If this product proves unsatisfactory please contact our customer service department
on freephone 0800 862 0453 or by e-mail ukservice@euro-pro.com.
9www.sharkclean.eu
Page 10
NOTES
10 0800 862 0453
Page 11
NOTES
11www.sharkclean.eu
Page 12
Euro-Pro Europe Limited
15 Mariner Court
Calder Park
Wakefield
WF4 3FL
Freephone 0800 862 0453
www.sharkclean.eu
Copyright © 2015 Euro-Pro Operating LLC
Shark and Euro-Pro are registered trademarks of Euro Pro
Operating LLC.
Printed in China
Illustrations may differ from actual product. We are constantly
striving to improve our products, therefore the specifications
contained herein are subject to change without notice.
Printed in China
SV769UK_150513_1
Loading...